arch/arm/boot/dts/omap3-evm-common.dtsi

   1 /*
   2  * Common support for omap3 EVM boards
   3  */
   4
   5 #include "omap-gpmc-smsc911x.dtsi"
   6
   7 / {
   8         cpus {
   9                 cpu@0 {
  10                         cpu0-supply = <&vcc>;
  11                 };
  12         };
  13
  14         leds {
  15                 compatible = "gpio-leds";
  16                 ledb {
  17                         label = "omap3evm::ledb";
  18                         gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
  19                         linux,default-trigger = "default-on";
  20                 };
  21         };
  22
  23         wl12xx_vmmc: wl12xx_vmmc {
  24                 compatible = "regulator-fixed";
  25                 regulator-name = "vwl1271";
  26                 regulator-min-microvolt = <1800000>;
  27                 regulator-max-microvolt = <1800000>;
  28                 gpio = <&gpio5 22 0>;   /* gpio150 */
  29                 startup-delay-us = <70000>;
  30                 enable-active-high;
  31                 vin-supply = <&vmmc2>;
  32         };
  33 };
  34
  35 &i2c1 {
  36         clock-frequency = <2600000>;
  37
  38         twl: twl@48 {
  39                 reg = <0x48>;
  40                 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
  41                 interrupt-parent = <&intc>;
  42         };
  43 };
  44
  45 #include "twl4030.dtsi"
  46 #include "twl4030_omap3.dtsi"
  47 #include "omap3-panel-sharp-ls037v7dw01.dtsi"
  48
  49 &backlight0 {
  50         gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>;
  51 };
  52
  53 &i2c2 {
  54         clock-frequency = <400000>;
  55 };
  56
  57 &i2c3 {
  58         clock-frequency = <400000>;
  59
  60         /*
  61          * TVP5146 Video decoder-in for analog input support.
  62          */
  63         tvp5146@5c {
  64                 compatible = "ti,tvp5146m2";
  65                 reg = <0x5c>;
  66         };
  67 };
  68
  69 &lcd_3v3 {
  70         gpio = <&gpio5 25 GPIO_ACTIVE_LOW>;     /* gpio153 */
  71         enable-active-low;
  72 };
  73
  74 &lcd0 {
  75         enable-gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>;    /* gpio152, lcd INI */
  76         reset-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;     /* gpio155, lcd RESB */
  77         mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH        /* gpio154, lcd MO */
  78                       &gpio1 2 GPIO_ACTIVE_HIGH         /* gpio2, lcd LR */
  79                       &gpio1 3 GPIO_ACTIVE_HIGH>;       /* gpio3, lcd UD */
  80 };
  81
  82 &mcspi1 {
  83         tsc2046@0 {
  84                 interrupt-parent = <&gpio6>;
  85                 interrupts = <15 0>;            /* gpio175 */
  86                 pendown-gpio = <&gpio6 15 0>;
  87         };
  88 };
  89
  90 &mmc1 {
  91         vmmc-supply = <&vmmc1>;
  92         vmmc_aux-supply = <&vsim>;
  93         bus-width = <8>;
  94 };
  95
  96 &mmc2 {
  97         vmmc-supply = <&wl12xx_vmmc>;
  98         non-removable;
  99         bus-width = <4>;
 100         cap-power-off-card;
 101 };
 102
 103 &twl_gpio {
 104         ti,use-leds;
 105 };
 106
 107 &usb_otg_hs {
 108         interface-type = <0>;
 109         usb-phy = <&usb2_phy>;
 110         phys = <&usb2_phy>;
 111         phy-names = "usb2-phy";
 112         mode = <3>;
 113         power = <50>;
 114 };
 115
 116 &gpmc {
 117         ethernet@gpmc {
 118                 interrupt-parent = <&gpio6>;
 119                 interrupts = <16 8>;
 120                 reg = <5 0 0xff>;
 121         };
 122 };