arch/arm/mach-shmobile/board-bonito.c

   1 /*
   2  * bonito board support
   3  *
   4  * Copyright (C) 2011 Renesas Solutions Corp.
   5  * Copyright (C) 2011 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
   6  *
   7  * This program is free software; you can redistribute it and/or modify
   8  * it under the terms of the GNU General Public License as published by
   9  * the Free Software Foundation; version 2 of the License.
  10  *
  11  * This program is distributed in the hope that it will be useful,
  12  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  13  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  14  * GNU General Public License for more details.
  15  *
  16  * You should have received a copy of the GNU General Public License
  17  * along with this program; if not, write to the Free Software
  18  * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  19  *
  20  */
  21
  22 #include <linux/kernel.h>
  23 #include <linux/i2c.h>
  24 #include <linux/init.h>
  25 #include <linux/interrupt.h>
  26 #include <linux/irq.h>
  27 #include <linux/platform_device.h>
  28 #include <linux/gpio.h>
  29 #include <linux/smsc911x.h>
  30 #include <mach/common.h>
  31 #include <asm/mach-types.h>
  32 #include <asm/mach/arch.h>
  33 #include <asm/mach/map.h>
  34 #include <asm/mach/time.h>
  35 #include <asm/hardware/cache-l2x0.h>
  36 #include <mach/r8a7740.h>
  37 #include <video/sh_mobile_lcdc.h>
  38
  39 /*
  40  * CS   Address         device                  note
  41  *----------------------------------------------------------------
  42  * 0    0x0000_0000     NOR Flash (64MB)        SW12 : bit3 = OFF
  43  * 2    0x0800_0000     ExtNOR (64MB)           SW12 : bit3 = OFF
  44  * 4                    -
  45  * 5A                   -
  46  * 5B   0x1600_0000     SRAM (8MB)
  47  * 6    0x1800_0000     FPGA (64K)
  48  *      0x1801_0000     Ether (4KB)
  49  *      0x1801_1000     USB (4KB)
  50  */
  51
  52 /*
  53  * SW12
  54  *
  55  *      bit1                    bit2                    bit3
  56  *----------------------------------------------------------------------------
  57  * ON   NOR WriteProtect        NAND WriteProtect       CS0 ExtNOR / CS2 NOR
  58  * OFF  NOR Not WriteProtect    NAND Not WriteProtect   CS0 NOR    / CS2 ExtNOR
  59  */
  60
  61 /*
  62  * SCIFA5 (CN42)
  63  *
  64  * S38.3 = ON
  65  * S39.6 = ON
  66  * S43.1 = ON
  67  */
  68
  69 /*
  70  * LCDC0 (CN3/CN4/CN7)
  71  *
  72  * S38.1 = OFF
  73  * S38.2 = OFF
  74  */
  75
  76 /*
  77  * FPGA
  78  */
  79 #define IRQSR0          0x0020
  80 #define IRQSR1          0x0022
  81 #define IRQMR0          0x0030
  82 #define IRQMR1          0x0032
  83 #define BUSSWMR1        0x0070
  84 #define BUSSWMR2        0x0072
  85 #define BUSSWMR3        0x0074
  86 #define BUSSWMR4        0x0076
  87
  88 #define LCDCR           0x10B4
  89 #define DEVRSTCR1       0x10D0
  90 #define DEVRSTCR2       0x10D2
  91 #define A1MDSR          0x10E0
  92 #define BVERR           0x1100
  93
  94 /* FPGA IRQ */
  95 #define FPGA_IRQ_BASE           (512)
  96 #define FPGA_IRQ0               (FPGA_IRQ_BASE)
  97 #define FPGA_IRQ1               (FPGA_IRQ_BASE + 16)
  98 #define FPGA_ETH_IRQ            (FPGA_IRQ0 + 15)
  99 static u16 bonito_fpga_read(u32 offset)
 100 {
 101         return __raw_readw(0xf0003000 + offset);
 102 }
 103
 104 static void bonito_fpga_write(u32 offset, u16 val)
 105 {
 106         __raw_writew(val, 0xf0003000 + offset);
 107 }
 108
 109 static void bonito_fpga_irq_disable(struct irq_data *data)
 110 {
 111         unsigned int irq = data->irq;
 112         u32 addr = (irq < 1016) ? IRQMR0 : IRQMR1;
 113         int shift = irq % 16;
 114
 115         bonito_fpga_write(addr, bonito_fpga_read(addr) | (1 << shift));
 116 }
 117
 118 static void bonito_fpga_irq_enable(struct irq_data *data)
 119 {
 120         unsigned int irq = data->irq;
 121         u32 addr = (irq < 1016) ? IRQMR0 : IRQMR1;
 122         int shift = irq % 16;
 123
 124         bonito_fpga_write(addr, bonito_fpga_read(addr) & ~(1 << shift));
 125 }
 126
 127 static struct irq_chip bonito_fpga_irq_chip __read_mostly = {
 128         .name           = "bonito FPGA",
 129         .irq_mask       = bonito_fpga_irq_disable,
 130         .irq_unmask     = bonito_fpga_irq_enable,
 131 };
 132
 133 static void bonito_fpga_irq_demux(unsigned int irq, struct irq_desc *desc)
 134 {
 135         u32 val =  bonito_fpga_read(IRQSR1) << 16 |
 136                    bonito_fpga_read(IRQSR0);
 137         u32 mask = bonito_fpga_read(IRQMR1) << 16 |
 138                    bonito_fpga_read(IRQMR0);
 139
 140         int i;
 141
 142         val &= ~mask;
 143
 144         for (i = 0; i < 32; i++) {
 145                 if (!(val & (1 << i)))
 146                         continue;
 147
 148                 generic_handle_irq(FPGA_IRQ_BASE + i);
 149         }
 150 }
 151
 152 static void bonito_fpga_init(void)
 153 {
 154         int i;
 155
 156         bonito_fpga_write(IRQMR0, 0xffff); /* mask all */
 157         bonito_fpga_write(IRQMR1, 0xffff); /* mask all */
 158
 159         /* Device reset */
 160         bonito_fpga_write(DEVRSTCR1,
 161                    (1 << 2));   /* Eth */
 162
 163         /* FPGA irq require special handling */
 164         for (i = FPGA_IRQ_BASE; i < FPGA_IRQ_BASE + 32; i++) {
 165                 irq_set_chip_and_handler_name(i, &bonito_fpga_irq_chip,
 166                                               handle_level_irq, "level");
 167                 set_irq_flags(i, IRQF_VALID); /* yuck */
 168         }
 169
 170         irq_set_chained_handler(evt2irq(0x0340), bonito_fpga_irq_demux);
 171         irq_set_irq_type(evt2irq(0x0340), IRQ_TYPE_LEVEL_LOW);
 172 }
 173
 174 /*
 175 * PMIC settings
 176 *
 177 * FIXME
 178 *
 179 * bonito board needs some settings by pmic which use i2c access.
 180 * pmic settings use device_initcall() here for use it.
 181 */
 182 static __u8 *pmic_settings = NULL;
 183 static __u8 pmic_do_2A[] = {
 184         0x1C, 0x09,
 185         0x1A, 0x80,
 186         0xff, 0xff,
 187 };
 188
 189 static int __init pmic_init(void)
 190 {
 191         struct i2c_adapter *a = i2c_get_adapter(0);
 192         struct i2c_msg msg;
 193         __u8 buf[2];
 194         int i, ret;
 195
 196         if (!pmic_settings)
 197                 return 0;
 198         if (!a)
 199                 return 0;
 200
 201         msg.addr        = 0x46;
 202         msg.buf         = buf;
 203         msg.len         = 2;
 204         msg.flags       = 0;
 205
 206         for (i = 0; ; i += 2) {
 207                 buf[0] = pmic_settings[i + 0];
 208                 buf[1] = pmic_settings[i + 1];
 209
 210                 if ((0xff == buf[0]) && (0xff == buf[1]))
 211                         break;
 212
 213                 ret = i2c_transfer(a, &msg, 1);
 214                 if (ret < 0) {
 215                         pr_err("i2c transfer fail\n");
 216                         break;
 217                 }
 218         }
 219
 220         return 0;
 221 }
 222 device_initcall(pmic_init);
 223
 224 /*
 225  * LCDC0
 226  */
 227 static const struct fb_videomode lcdc0_mode = {
 228         .name           = "WVGA Panel",
 229         .xres           = 800,
 230         .yres           = 480,
 231         .left_margin    = 88,
 232         .right_margin   = 40,
 233         .hsync_len      = 128,
 234         .upper_margin   = 20,
 235         .lower_margin   = 5,
 236         .vsync_len      = 5,
 237         .sync           = 0,
 238 };
 239
 240 static struct sh_mobile_lcdc_info lcdc0_info = {
 241         .clock_source   = LCDC_CLK_BUS,
 242         .ch[0] = {
 243                 .chan                   = LCDC_CHAN_MAINLCD,
 244                 .bpp                    = 16,
 245                 .interface_type         = RGB24,
 246                 .clock_divider          = 5,
 247                 .flags                  = 0,
 248                 .lcd_cfg                = &lcdc0_mode,
 249                 .num_cfg                = 1,
 250                 .lcd_size_cfg = {
 251                         .width  = 152,
 252                         .height = 91,
 253                 },
 254         },
 255 };
 256
 257 static struct resource lcdc0_resources[] = {
 258         [0] = {
 259                 .name   = "LCDC0",
 260                 .start  = 0xfe940000,
 261                 .end    = 0xfe943fff,
 262                 .flags  = IORESOURCE_MEM,
 263         },
 264         [1] = {
 265                 .start  = intcs_evt2irq(0x0580),
 266                 .flags  = IORESOURCE_IRQ,
 267         },
 268 };
 269
 270 static struct platform_device lcdc0_device = {
 271         .name           = "sh_mobile_lcdc_fb",
 272         .id             = 0,
 273         .resource       = lcdc0_resources,
 274         .num_resources  = ARRAY_SIZE(lcdc0_resources),
 275         .dev    = {
 276                 .platform_data  = &lcdc0_info,
 277                 .coherent_dma_mask = ~0,
 278         },
 279 };
 280
 281 /*
 282  * SMSC 9221
 283  */
 284 static struct resource smsc_resources[] = {
 285         [0] = {
 286                 .start          = 0x18010000,
 287                 .end            = 0x18011000 - 1,
 288                 .flags          = IORESOURCE_MEM,
 289         },
 290         [1] = {
 291                 .start          = FPGA_ETH_IRQ,
 292                 .flags          = IORESOURCE_IRQ,
 293         },
 294 };
 295
 296 static struct smsc911x_platform_config smsc_platdata = {
 297         .flags          = SMSC911X_USE_16BIT,
 298         .phy_interface  = PHY_INTERFACE_MODE_MII,
 299         .irq_polarity   = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
 300         .irq_type       = SMSC911X_IRQ_TYPE_PUSH_PULL,
 301 };
 302
 303 static struct platform_device smsc_device = {
 304         .name           = "smsc911x",
 305         .dev  = {
 306                 .platform_data = &smsc_platdata,
 307         },
 308         .resource       = smsc_resources,
 309         .num_resources  = ARRAY_SIZE(smsc_resources),
 310 };
 311
 312 /*
 313  * core board devices
 314  */
 315 static struct platform_device *bonito_core_devices[] __initdata = {
 316 };
 317
 318 /*
 319  * base board devices
 320  */
 321 static struct platform_device *bonito_base_devices[] __initdata = {
 322         &lcdc0_device,
 323         &smsc_device,
 324 };
 325
 326 /*
 327  * map I/O
 328  */
 329 static struct map_desc bonito_io_desc[] __initdata = {
 330          /*
 331           * for CPGA/INTC/PFC
 332           * 0xe6000000-0xefffffff -> 0xe6000000-0xefffffff
 333           */
 334         {
 335                 .virtual        = 0xe6000000,
 336                 .pfn            = __phys_to_pfn(0xe6000000),
 337                 .length         = 160 << 20,
 338                 .type           = MT_DEVICE_NONSHARED
 339         },
 340 #ifdef CONFIG_CACHE_L2X0
 341         /*
 342          * for l2x0_init()
 343          * 0xf0100000-0xf0101000 -> 0xf0002000-0xf0003000
 344          */
 345         {
 346                 .virtual        = 0xf0002000,
 347                 .pfn            = __phys_to_pfn(0xf0100000),
 348                 .length         = PAGE_SIZE,
 349                 .type           = MT_DEVICE_NONSHARED
 350         },
 351 #endif
 352         /*
 353          * for FPGA (0x1800000-0x19ffffff)
 354          * 0x18000000-0x18002000 -> 0xf0003000-0xf0005000
 355          */
 356         {
 357                 .virtual        = 0xf0003000,
 358                 .pfn            = __phys_to_pfn(0x18000000),
 359                 .length         = PAGE_SIZE * 2,
 360                 .type           = MT_DEVICE_NONSHARED
 361         }
 362 };
 363
 364 static void __init bonito_map_io(void)
 365 {
 366         iotable_init(bonito_io_desc, ARRAY_SIZE(bonito_io_desc));
 367
 368         /* setup early devices and console here as well */
 369         r8a7740_add_early_devices();
 370         shmobile_setup_console();
 371 }
 372
 373 /*
 374  * board init
 375  */
 376 #define BIT_ON(sw, bit)         (sw & (1 << bit))
 377 #define BIT_OFF(sw, bit)        (!(sw & (1 << bit)))
 378
 379 #define VCCQ1CR         0xE6058140
 380 #define VCCQ1LCDCR      0xE6058186
 381
 382 static void __init bonito_init(void)
 383 {
 384         u16 val;
 385
 386         r8a7740_pinmux_init();
 387         bonito_fpga_init();
 388
 389         pmic_settings = pmic_do_2A;
 390
 391         /*
 392          * core board settings
 393          */
 394
 395 #ifdef CONFIG_CACHE_L2X0
 396         /* Early BRESP enable, Shared attribute override enable, 32K*8way */
 397         l2x0_init(__io(0xf0002000), 0x40440000, 0x82000fff);
 398 #endif
 399
 400         r8a7740_add_standard_devices();
 401
 402         platform_add_devices(bonito_core_devices,
 403                              ARRAY_SIZE(bonito_core_devices));
 404
 405         /*
 406          * base board settings
 407          */
 408         gpio_request(GPIO_PORT176, NULL);
 409         gpio_direction_input(GPIO_PORT176);
 410         if (!gpio_get_value(GPIO_PORT176)) {
 411                 u16 bsw2;
 412                 u16 bsw3;
 413                 u16 bsw4;
 414
 415                 /*
 416                  * FPGA
 417                  */
 418                 gpio_request(GPIO_FN_CS5B,              NULL);
 419                 gpio_request(GPIO_FN_CS6A,              NULL);
 420                 gpio_request(GPIO_FN_CS5A_PORT105,      NULL);
 421                 gpio_request(GPIO_FN_IRQ10,             NULL);
 422
 423                 val = bonito_fpga_read(BVERR);
 424                 pr_info("bonito version: cpu %02x, base %02x\n",
 425                         ((val >> 8) & 0xFF),
 426                         ((val >> 0) & 0xFF));
 427
 428                 bsw2 = bonito_fpga_read(BUSSWMR2);
 429                 bsw3 = bonito_fpga_read(BUSSWMR3);
 430                 bsw4 = bonito_fpga_read(BUSSWMR4);
 431
 432                 /*
 433                  * SCIFA5 (CN42)
 434                  */
 435                 if (BIT_OFF(bsw2, 1) && /* S38.3 = ON */
 436                     BIT_OFF(bsw3, 9) && /* S39.6 = ON */
 437                     BIT_OFF(bsw4, 4)) { /* S43.1 = ON */
 438                         gpio_request(GPIO_FN_SCIFA5_TXD_PORT91, NULL);
 439                         gpio_request(GPIO_FN_SCIFA5_RXD_PORT92, NULL);
 440                 }
 441
 442                 /*
 443                  * LCDC0 (CN3)
 444                  */
 445                 if (BIT_ON(bsw2, 3) &&  /* S38.1 = OFF */
 446                     BIT_ON(bsw2, 2)) {  /* S38.2 = OFF */
 447                         gpio_request(GPIO_FN_LCDC0_SELECT,      NULL);
 448                         gpio_request(GPIO_FN_LCD0_D0,           NULL);
 449                         gpio_request(GPIO_FN_LCD0_D1,           NULL);
 450                         gpio_request(GPIO_FN_LCD0_D2,           NULL);
 451                         gpio_request(GPIO_FN_LCD0_D3,           NULL);
 452                         gpio_request(GPIO_FN_LCD0_D4,           NULL);
 453                         gpio_request(GPIO_FN_LCD0_D5,           NULL);
 454                         gpio_request(GPIO_FN_LCD0_D6,           NULL);
 455                         gpio_request(GPIO_FN_LCD0_D7,           NULL);
 456                         gpio_request(GPIO_FN_LCD0_D8,           NULL);
 457                         gpio_request(GPIO_FN_LCD0_D9,           NULL);
 458                         gpio_request(GPIO_FN_LCD0_D10,          NULL);
 459                         gpio_request(GPIO_FN_LCD0_D11,          NULL);
 460                         gpio_request(GPIO_FN_LCD0_D12,          NULL);
 461                         gpio_request(GPIO_FN_LCD0_D13,          NULL);
 462                         gpio_request(GPIO_FN_LCD0_D14,          NULL);
 463                         gpio_request(GPIO_FN_LCD0_D15,          NULL);
 464                         gpio_request(GPIO_FN_LCD0_D16,          NULL);
 465                         gpio_request(GPIO_FN_LCD0_D17,          NULL);
 466                         gpio_request(GPIO_FN_LCD0_D18_PORT163,  NULL);
 467                         gpio_request(GPIO_FN_LCD0_D19_PORT162,  NULL);
 468                         gpio_request(GPIO_FN_LCD0_D20_PORT161,  NULL);
 469                         gpio_request(GPIO_FN_LCD0_D21_PORT158,  NULL);
 470                         gpio_request(GPIO_FN_LCD0_D22_PORT160,  NULL);
 471                         gpio_request(GPIO_FN_LCD0_D23_PORT159,  NULL);
 472                         gpio_request(GPIO_FN_LCD0_DCK,          NULL);
 473                         gpio_request(GPIO_FN_LCD0_VSYN,         NULL);
 474                         gpio_request(GPIO_FN_LCD0_HSYN,         NULL);
 475                         gpio_request(GPIO_FN_LCD0_DISP,         NULL);
 476                         gpio_request(GPIO_FN_LCD0_LCLK_PORT165, NULL);
 477
 478                         gpio_request(GPIO_PORT61, NULL); /* LCDDON */
 479                         gpio_direction_output(GPIO_PORT61, 1);
 480
 481                         /* backlight on */
 482                         bonito_fpga_write(LCDCR, 1);
 483
 484                         /*  drivability Max */
 485                         __raw_writew(0x00FF , VCCQ1LCDCR);
 486                         __raw_writew(0xFFFF , VCCQ1CR);
 487                 }
 488
 489                 platform_add_devices(bonito_base_devices,
 490                                      ARRAY_SIZE(bonito_base_devices));
 491         }
 492 }
 493
 494 static void __init bonito_timer_init(void)
 495 {
 496         u16 val;
 497         u8 md_ck = 0;
 498
 499         /* read MD_CK value */
 500         val = bonito_fpga_read(A1MDSR);
 501         if (val & (1 << 10))
 502                 md_ck |= MD_CK2;
 503         if (val & (1 << 9))
 504                 md_ck |= MD_CK1;
 505         if (val & (1 << 8))
 506                 md_ck |= MD_CK0;
 507
 508         r8a7740_clock_init(md_ck);
 509         shmobile_timer.init();
 510 }
 511
 512 struct sys_timer bonito_timer = {
 513         .init   = bonito_timer_init,
 514 };
 515
 516 MACHINE_START(BONITO, "bonito")
 517         .map_io         = bonito_map_io,
 518         .init_irq       = r8a7740_init_irq,
 519         .handle_irq     = shmobile_handle_irq_intc,
 520         .init_machine   = bonito_init,
 521         .timer          = &bonito_timer,
 522 MACHINE_END