1 /*******************************************************************************
3 Intel(R) Gigabit Ethernet Linux driver
4 Copyright(c) 2007-2014 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, see <http://www.gnu.org/licenses/>.
18 The full GNU General Public License is included in this distribution in
19 the file called "COPYING".
22 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
23 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
25 *******************************************************************************/
27 #ifndef _E1000_DEFINES_H_
28 #define _E1000_DEFINES_H_
30 /* Number of Transmit and Receive Descriptors must be a multiple of 8 */
31 #define REQ_TX_DESCRIPTOR_MULTIPLE 8
32 #define REQ_RX_DESCRIPTOR_MULTIPLE 8
34 /* Definitions for power management and wakeup registers */
36 #define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
38 /* Wake Up Filter Control */
39 #define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
40 #define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
41 #define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
42 #define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
43 #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
45 /* Extended Device Control */
46 #define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Defineable Pin 3 */
47 /* Physical Func Reset Done Indication */
48 #define E1000_CTRL_EXT_PFRSTD 0x00004000
49 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
50 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
51 #define E1000_CTRL_EXT_LINK_MODE_1000BASE_KX 0x00400000
52 #define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
53 #define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000
54 #define E1000_CTRL_EXT_EIAME 0x01000000
55 #define E1000_CTRL_EXT_IRCA 0x00000001
56 /* Interrupt delay cancellation */
57 /* Driver loaded bit for FW */
58 #define E1000_CTRL_EXT_DRV_LOAD 0x10000000
59 /* Interrupt acknowledge Auto-mask */
60 /* Clear Interrupt timers after IMS clear */
61 /* packet buffer parity error detection enabled */
62 /* descriptor FIFO parity error detection enable */
63 #define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
64 #define E1000_I2CCMD_REG_ADDR_SHIFT 16
65 #define E1000_I2CCMD_PHY_ADDR_SHIFT 24
66 #define E1000_I2CCMD_OPCODE_READ 0x08000000
67 #define E1000_I2CCMD_OPCODE_WRITE 0x00000000
68 #define E1000_I2CCMD_READY 0x20000000
69 #define E1000_I2CCMD_ERROR 0x80000000
70 #define E1000_I2CCMD_SFP_DATA_ADDR(a) (0x0000 + (a))
71 #define E1000_I2CCMD_SFP_DIAG_ADDR(a) (0x0100 + (a))
72 #define E1000_MAX_SGMII_PHY_REG_ADDR 255
73 #define E1000_I2CCMD_PHY_TIMEOUT 200
74 #define E1000_IVAR_VALID 0x80
75 #define E1000_GPIE_NSICR 0x00000001
76 #define E1000_GPIE_MSIX_MODE 0x00000010
77 #define E1000_GPIE_EIAME 0x40000000
78 #define E1000_GPIE_PBA 0x80000000
80 /* Receive Descriptor bit definitions */
81 #define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
82 #define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
83 #define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
84 #define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
85 #define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
86 #define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
87 #define E1000_RXD_STAT_TS 0x10000 /* Pkt was time stamped */
89 #define E1000_RXDEXT_STATERR_LB 0x00040000
90 #define E1000_RXDEXT_STATERR_CE 0x01000000
91 #define E1000_RXDEXT_STATERR_SE 0x02000000
92 #define E1000_RXDEXT_STATERR_SEQ 0x04000000
93 #define E1000_RXDEXT_STATERR_CXE 0x10000000
94 #define E1000_RXDEXT_STATERR_TCPE 0x20000000
95 #define E1000_RXDEXT_STATERR_IPE 0x40000000
96 #define E1000_RXDEXT_STATERR_RXE 0x80000000
98 /* Same mask, but for extended and packet split descriptors */
99 #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
100 E1000_RXDEXT_STATERR_CE | \
101 E1000_RXDEXT_STATERR_SE | \
102 E1000_RXDEXT_STATERR_SEQ | \
103 E1000_RXDEXT_STATERR_CXE | \
104 E1000_RXDEXT_STATERR_RXE)
106 #define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
107 #define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
108 #define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
109 #define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
110 #define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
113 /* Management Control */
114 #define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
115 #define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
116 #define E1000_MANC_EN_BMC2OS 0x10000000 /* OSBMC is Enabled or not */
117 /* Enable Neighbor Discovery Filtering */
118 #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
119 #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
120 /* Enable MAC address filtering */
121 #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
123 /* Receive Control */
124 #define E1000_RCTL_EN 0x00000002 /* enable */
125 #define E1000_RCTL_SBP 0x00000004 /* store bad packet */
126 #define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
127 #define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
128 #define E1000_RCTL_LPE 0x00000020 /* long packet enable */
129 #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
130 #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
131 #define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
132 #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
133 #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
134 #define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
135 #define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
136 #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
137 #define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
138 #define E1000_RCTL_DPF 0x00400000 /* Discard Pause Frames */
139 #define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
140 #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
142 /* Use byte values for the following shift parameters
144 * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
145 * E1000_PSRCTL_BSIZE0_MASK) |
146 * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
147 * E1000_PSRCTL_BSIZE1_MASK) |
148 * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
149 * E1000_PSRCTL_BSIZE2_MASK) |
150 * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
151 * E1000_PSRCTL_BSIZE3_MASK))
152 * where value0 = [128..16256], default=256
153 * value1 = [1024..64512], default=4096
154 * value2 = [0..64512], default=4096
155 * value3 = [0..64512], default=0
158 #define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
159 #define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
160 #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
161 #define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
163 #define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
164 #define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
165 #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
166 #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
168 /* SWFW_SYNC Definitions */
169 #define E1000_SWFW_EEP_SM 0x1
170 #define E1000_SWFW_PHY0_SM 0x2
171 #define E1000_SWFW_PHY1_SM 0x4
172 #define E1000_SWFW_PHY2_SM 0x20
173 #define E1000_SWFW_PHY3_SM 0x40
175 /* FACTPS Definitions */
177 #define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
178 #define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
179 #define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
180 #define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
181 #define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
182 #define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
183 #define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
184 #define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
185 #define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
186 #define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
187 #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
188 /* Defined polarity of Dock/Undock indication in SDP[0] */
189 /* Reset both PHY ports, through PHYRST_N pin */
190 /* enable link status from external LINK_0 and LINK_1 pins */
191 #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
192 #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
193 #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
194 #define E1000_CTRL_RST 0x04000000 /* Global reset */
195 #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
196 #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
197 #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
198 #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
199 /* Initiate an interrupt to manageability engine */
200 #define E1000_CTRL_I2C_ENA 0x02000000 /* I2C enable */
202 /* Bit definitions for the Management Data IO (MDIO) and Management Data
203 * Clock (MDC) pins in the Device Control Register.
206 #define E1000_CONNSW_ENRGSRC 0x4
207 #define E1000_CONNSW_PHYSD 0x400
208 #define E1000_CONNSW_PHY_PDN 0x800
209 #define E1000_CONNSW_SERDESD 0x200
210 #define E1000_CONNSW_AUTOSENSE_CONF 0x2
211 #define E1000_CONNSW_AUTOSENSE_EN 0x1
212 #define E1000_PCS_CFG_PCS_EN 8
213 #define E1000_PCS_LCTL_FLV_LINK_UP 1
214 #define E1000_PCS_LCTL_FSV_100 2
215 #define E1000_PCS_LCTL_FSV_1000 4
216 #define E1000_PCS_LCTL_FDV_FULL 8
217 #define E1000_PCS_LCTL_FSD 0x10
218 #define E1000_PCS_LCTL_FORCE_LINK 0x20
219 #define E1000_PCS_LCTL_FORCE_FCTRL 0x80
220 #define E1000_PCS_LCTL_AN_ENABLE 0x10000
221 #define E1000_PCS_LCTL_AN_RESTART 0x20000
222 #define E1000_PCS_LCTL_AN_TIMEOUT 0x40000
223 #define E1000_ENABLE_SERDES_LOOPBACK 0x0410
225 #define E1000_PCS_LSTS_LINK_OK 1
226 #define E1000_PCS_LSTS_SPEED_100 2
227 #define E1000_PCS_LSTS_SPEED_1000 4
228 #define E1000_PCS_LSTS_DUPLEX_FULL 8
229 #define E1000_PCS_LSTS_SYNK_OK 0x10
232 #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
233 #define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
234 #define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
235 #define E1000_STATUS_FUNC_SHIFT 2
236 #define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
237 #define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
238 #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
239 #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
240 /* Change in Dock/Undock state. Clear on write '0'. */
241 /* Status of Master requests. */
242 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000
243 /* BMC external code execution disabled */
245 #define E1000_STATUS_2P5_SKU 0x00001000 /* Val of 2.5GBE SKU strap */
246 #define E1000_STATUS_2P5_SKU_OVER 0x00002000 /* Val of 2.5GBE SKU Over */
247 /* Constants used to intrepret the masked PCI-X bus speed. */
250 #define SPEED_100 100
251 #define SPEED_1000 1000
252 #define SPEED_2500 2500
253 #define HALF_DUPLEX 1
254 #define FULL_DUPLEX 2
257 #define ADVERTISE_10_HALF 0x0001
258 #define ADVERTISE_10_FULL 0x0002
259 #define ADVERTISE_100_HALF 0x0004
260 #define ADVERTISE_100_FULL 0x0008
261 #define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */
262 #define ADVERTISE_1000_FULL 0x0020
264 /* 1000/H is not supported, nor spec-compliant. */
265 #define E1000_ALL_SPEED_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
266 ADVERTISE_100_HALF | ADVERTISE_100_FULL | \
268 #define E1000_ALL_NOT_GIG (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
269 ADVERTISE_100_HALF | ADVERTISE_100_FULL)
270 #define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
271 #define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
272 #define E1000_ALL_FULL_DUPLEX (ADVERTISE_10_FULL | ADVERTISE_100_FULL | \
274 #define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
276 #define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
279 #define E1000_LEDCTL_LED0_MODE_SHIFT 0
280 #define E1000_LEDCTL_LED0_BLINK 0x00000080
281 #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
282 #define E1000_LEDCTL_LED0_IVRT 0x00000040
284 #define E1000_LEDCTL_MODE_LED_ON 0xE
285 #define E1000_LEDCTL_MODE_LED_OFF 0xF
287 /* Transmit Descriptor bit definitions */
288 #define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
289 #define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
290 #define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
291 #define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
292 #define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
293 #define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
294 #define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
295 /* Extended desc bits for Linksec and timesync */
297 /* Transmit Control */
298 #define E1000_TCTL_EN 0x00000002 /* enable tx */
299 #define E1000_TCTL_PSP 0x00000008 /* pad short packets */
300 #define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
301 #define E1000_TCTL_COLD 0x003ff000 /* collision distance */
302 #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
304 /* DMA Coalescing register fields */
305 #define E1000_DMACR_DMACWT_MASK 0x00003FFF /* DMA Coalescing
307 #define E1000_DMACR_DMACTHR_MASK 0x00FF0000 /* DMA Coalescing Receive
309 #define E1000_DMACR_DMACTHR_SHIFT 16
310 #define E1000_DMACR_DMAC_LX_MASK 0x30000000 /* Lx when no PCIe
312 #define E1000_DMACR_DMAC_LX_SHIFT 28
313 #define E1000_DMACR_DMAC_EN 0x80000000 /* Enable DMA Coalescing */
314 /* DMA Coalescing BMC-to-OS Watchdog Enable */
315 #define E1000_DMACR_DC_BMC2OSW_EN 0x00008000
317 #define E1000_DMCTXTH_DMCTTHR_MASK 0x00000FFF /* DMA Coalescing Transmit
320 #define E1000_DMCTLX_TTLX_MASK 0x00000FFF /* Time to LX request */
322 #define E1000_DMCRTRH_UTRESH_MASK 0x0007FFFF /* Receive Traffic Rate
324 #define E1000_DMCRTRH_LRPRCW 0x80000000 /* Rcv packet rate in
327 #define E1000_DMCCNT_CCOUNT_MASK 0x01FFFFFF /* DMA Coal Rcv Traffic
330 #define E1000_FCRTC_RTH_COAL_MASK 0x0003FFF0 /* Flow ctrl Rcv Threshold
332 #define E1000_FCRTC_RTH_COAL_SHIFT 4
333 #define E1000_PCIEMISC_LX_DECISION 0x00000080 /* Lx power decision */
335 /* Timestamp in Rx buffer */
336 #define E1000_RXPBS_CFG_TS_EN 0x80000000
339 #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
341 /* Receive Checksum Control */
342 #define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */
343 #define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
344 #define E1000_RXCSUM_CRCOFL 0x00000800 /* CRC32 offload enable */
345 #define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
347 /* Header split receive */
348 #define E1000_RFCTL_LEF 0x00040000
350 /* Collision related configuration parameters */
351 #define E1000_COLLISION_THRESHOLD 15
352 #define E1000_CT_SHIFT 4
353 #define E1000_COLLISION_DISTANCE 63
354 #define E1000_COLD_SHIFT 12
356 /* Ethertype field values */
357 #define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
359 #define MAX_JUMBO_FRAME_SIZE 0x3F00
362 #define E1000_PBA_34K 0x0022
363 #define E1000_PBA_64K 0x0040 /* 64KB */
365 /* SW Semaphore Register */
366 #define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
367 #define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
369 /* Interrupt Cause Read */
370 #define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
371 #define E1000_ICR_LSC 0x00000004 /* Link Status Change */
372 #define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
373 #define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
374 #define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
375 #define E1000_ICR_VMMB 0x00000100 /* VM MB event */
376 #define E1000_ICR_TS 0x00080000 /* Time Sync Interrupt */
377 #define E1000_ICR_DRSTA 0x40000000 /* Device Reset Asserted */
378 /* If this bit asserted, the driver should claim the interrupt */
379 #define E1000_ICR_INT_ASSERTED 0x80000000
380 /* LAN connected device generates an interrupt */
381 #define E1000_ICR_DOUTSYNC 0x10000000 /* NIC DMA out of sync */
383 /* Extended Interrupt Cause Read */
384 #define E1000_EICR_RX_QUEUE0 0x00000001 /* Rx Queue 0 Interrupt */
385 #define E1000_EICR_RX_QUEUE1 0x00000002 /* Rx Queue 1 Interrupt */
386 #define E1000_EICR_RX_QUEUE2 0x00000004 /* Rx Queue 2 Interrupt */
387 #define E1000_EICR_RX_QUEUE3 0x00000008 /* Rx Queue 3 Interrupt */
388 #define E1000_EICR_TX_QUEUE0 0x00000100 /* Tx Queue 0 Interrupt */
389 #define E1000_EICR_TX_QUEUE1 0x00000200 /* Tx Queue 1 Interrupt */
390 #define E1000_EICR_TX_QUEUE2 0x00000400 /* Tx Queue 2 Interrupt */
391 #define E1000_EICR_TX_QUEUE3 0x00000800 /* Tx Queue 3 Interrupt */
392 #define E1000_EICR_OTHER 0x80000000 /* Interrupt Cause Active */
395 /* This defines the bits that are set in the Interrupt Mask
396 * Set/Read Register. Each bit is documented below:
397 * o RXT0 = Receiver Timer Interrupt (ring 0)
398 * o TXDW = Transmit Descriptor Written Back
399 * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
400 * o RXSEQ = Receive Sequence Error
401 * o LSC = Link Status Change
403 #define IMS_ENABLE_MASK ( \
411 /* Interrupt Mask Set */
412 #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
413 #define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
414 #define E1000_IMS_VMMB E1000_ICR_VMMB /* Mail box activity */
415 #define E1000_IMS_TS E1000_ICR_TS /* Time Sync Interrupt */
416 #define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
417 #define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
418 #define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
419 #define E1000_IMS_DRSTA E1000_ICR_DRSTA /* Device Reset Asserted */
420 #define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */
422 /* Extended Interrupt Mask Set */
423 #define E1000_EIMS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */
425 /* Interrupt Cause Set */
426 #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
427 #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
428 #define E1000_ICS_DRSTA E1000_ICR_DRSTA /* Device Reset Aserted */
430 /* Extended Interrupt Cause Set */
431 /* E1000_EITR_CNT_IGNR is only for 82576 and newer */
432 #define E1000_EITR_CNT_IGNR 0x80000000 /* Don't reset counters on write */
435 /* Transmit Descriptor Control */
436 /* Enable the counting of descriptors still to be processed. */
438 /* Flow Control Constants */
439 #define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
440 #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
441 #define FLOW_CONTROL_TYPE 0x8808
443 /* Transmit Config Word */
444 #define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
445 #define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
447 /* 802.1q VLAN Packet Size */
448 #define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */
449 #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
451 /* Receive Address */
452 /* Number of high/low register pairs in the RAR. The RAR (Receive Address
453 * Registers) holds the directed and multicast addresses that we monitor.
454 * Technically, we have 16 spots. However, we reserve one of these spots
455 * (RAR[15]) for our directed address used by controllers with
456 * manageability enabled, allowing us room for 15 multicast addresses.
458 #define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
459 #define E1000_RAL_MAC_ADDR_LEN 4
460 #define E1000_RAH_MAC_ADDR_LEN 2
461 #define E1000_RAH_POOL_MASK 0x03FC0000
462 #define E1000_RAH_POOL_1 0x00040000
465 #define E1000_SUCCESS 0
466 #define E1000_ERR_NVM 1
467 #define E1000_ERR_PHY 2
468 #define E1000_ERR_CONFIG 3
469 #define E1000_ERR_PARAM 4
470 #define E1000_ERR_MAC_INIT 5
471 #define E1000_ERR_RESET 9
472 #define E1000_ERR_MASTER_REQUESTS_PENDING 10
473 #define E1000_BLK_PHY_RESET 12
474 #define E1000_ERR_SWFW_SYNC 13
475 #define E1000_NOT_IMPLEMENTED 14
476 #define E1000_ERR_MBX 15
477 #define E1000_ERR_INVALID_ARGUMENT 16
478 #define E1000_ERR_NO_SPACE 17
479 #define E1000_ERR_NVM_PBA_SECTION 18
480 #define E1000_ERR_INVM_VALUE_NOT_FOUND 19
481 #define E1000_ERR_I2C 20
483 /* Loop limit on how long we wait for auto-negotiation to complete */
484 #define COPPER_LINK_UP_LIMIT 10
485 #define PHY_AUTO_NEG_LIMIT 45
486 #define PHY_FORCE_LIMIT 20
487 /* Number of 100 microseconds we wait for PCI Express master disable */
488 #define MASTER_DISABLE_TIMEOUT 800
489 /* Number of milliseconds we wait for PHY configuration done after MAC reset */
490 #define PHY_CFG_TIMEOUT 100
491 /* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
492 /* Number of milliseconds for NVM auto read done after MAC reset. */
493 #define AUTO_READ_DONE_TIMEOUT 10
496 #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
498 #define E1000_TSYNCTXCTL_VALID 0x00000001 /* tx timestamp valid */
499 #define E1000_TSYNCTXCTL_ENABLED 0x00000010 /* enable tx timestampping */
501 #define E1000_TSYNCRXCTL_VALID 0x00000001 /* rx timestamp valid */
502 #define E1000_TSYNCRXCTL_TYPE_MASK 0x0000000E /* rx type mask */
503 #define E1000_TSYNCRXCTL_TYPE_L2_V2 0x00
504 #define E1000_TSYNCRXCTL_TYPE_L4_V1 0x02
505 #define E1000_TSYNCRXCTL_TYPE_L2_L4_V2 0x04
506 #define E1000_TSYNCRXCTL_TYPE_ALL 0x08
507 #define E1000_TSYNCRXCTL_TYPE_EVENT_V2 0x0A
508 #define E1000_TSYNCRXCTL_ENABLED 0x00000010 /* enable rx timestampping */
510 #define E1000_TSYNCRXCFG_PTP_V1_CTRLT_MASK 0x000000FF
511 #define E1000_TSYNCRXCFG_PTP_V1_SYNC_MESSAGE 0x00
512 #define E1000_TSYNCRXCFG_PTP_V1_DELAY_REQ_MESSAGE 0x01
513 #define E1000_TSYNCRXCFG_PTP_V1_FOLLOWUP_MESSAGE 0x02
514 #define E1000_TSYNCRXCFG_PTP_V1_DELAY_RESP_MESSAGE 0x03
515 #define E1000_TSYNCRXCFG_PTP_V1_MANAGEMENT_MESSAGE 0x04
517 #define E1000_TSYNCRXCFG_PTP_V2_MSGID_MASK 0x00000F00
518 #define E1000_TSYNCRXCFG_PTP_V2_SYNC_MESSAGE 0x0000
519 #define E1000_TSYNCRXCFG_PTP_V2_DELAY_REQ_MESSAGE 0x0100
520 #define E1000_TSYNCRXCFG_PTP_V2_PATH_DELAY_REQ_MESSAGE 0x0200
521 #define E1000_TSYNCRXCFG_PTP_V2_PATH_DELAY_RESP_MESSAGE 0x0300
522 #define E1000_TSYNCRXCFG_PTP_V2_FOLLOWUP_MESSAGE 0x0800
523 #define E1000_TSYNCRXCFG_PTP_V2_DELAY_RESP_MESSAGE 0x0900
524 #define E1000_TSYNCRXCFG_PTP_V2_PATH_DELAY_FOLLOWUP_MESSAGE 0x0A00
525 #define E1000_TSYNCRXCFG_PTP_V2_ANNOUNCE_MESSAGE 0x0B00
526 #define E1000_TSYNCRXCFG_PTP_V2_SIGNALLING_MESSAGE 0x0C00
527 #define E1000_TSYNCRXCFG_PTP_V2_MANAGEMENT_MESSAGE 0x0D00
529 #define E1000_TIMINCA_16NS_SHIFT 24
531 #define E1000_TSICR_TXTS 0x00000002
532 #define E1000_TSIM_TXTS 0x00000002
534 #define E1000_MDICNFG_EXT_MDIO 0x80000000 /* MDI ext/int destination */
535 #define E1000_MDICNFG_COM_MDIO 0x40000000 /* MDI shared w/ lan 0 */
536 #define E1000_MDICNFG_PHY_MASK 0x03E00000
537 #define E1000_MDICNFG_PHY_SHIFT 21
539 #define E1000_MEDIA_PORT_COPPER 1
540 #define E1000_MEDIA_PORT_OTHER 2
541 #define E1000_M88E1112_AUTO_COPPER_SGMII 0x2
542 #define E1000_M88E1112_AUTO_COPPER_BASEX 0x3
543 #define E1000_M88E1112_STATUS_LINK 0x0004 /* Interface Link Bit */
544 #define E1000_M88E1112_MAC_CTRL_1 0x10
545 #define E1000_M88E1112_MAC_CTRL_1_MODE_MASK 0x0380 /* Mode Select */
546 #define E1000_M88E1112_MAC_CTRL_1_MODE_SHIFT 7
547 #define E1000_M88E1112_PAGE_ADDR 0x16
548 #define E1000_M88E1112_STATUS 0x01
550 /* PCI Express Control */
551 #define E1000_GCR_CMPL_TMOUT_MASK 0x0000F000
552 #define E1000_GCR_CMPL_TMOUT_10ms 0x00001000
553 #define E1000_GCR_CMPL_TMOUT_RESEND 0x00010000
554 #define E1000_GCR_CAP_VER2 0x00040000
556 /* mPHY Address Control and Data Registers */
557 #define E1000_MPHY_ADDR_CTL 0x0024 /* mPHY Address Control Register */
558 #define E1000_MPHY_ADDR_CTL_OFFSET_MASK 0xFFFF0000
559 #define E1000_MPHY_DATA 0x0E10 /* mPHY Data Register */
561 /* mPHY PCS CLK Register */
562 #define E1000_MPHY_PCS_CLK_REG_OFFSET 0x0004 /* mPHY PCS CLK AFE CSR Offset */
563 /* mPHY Near End Digital Loopback Override Bit */
564 #define E1000_MPHY_PCS_CLK_REG_DIGINELBEN 0x10
566 #define E1000_PCS_LCTL_FORCE_FCTRL 0x80
567 #define E1000_PCS_LSTS_AN_COMPLETE 0x10000
569 /* PHY Control Register */
570 #define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
571 #define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
572 #define MII_CR_POWER_DOWN 0x0800 /* Power down */
573 #define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
574 #define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
575 #define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
576 #define MII_CR_SPEED_1000 0x0040
577 #define MII_CR_SPEED_100 0x2000
578 #define MII_CR_SPEED_10 0x0000
580 /* PHY Status Register */
581 #define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
582 #define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
584 /* Autoneg Advertisement Register */
585 #define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
586 #define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
587 #define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
588 #define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
589 #define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
590 #define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
592 /* Link Partner Ability Register (Base Page) */
593 #define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
594 #define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
596 /* Autoneg Expansion Register */
598 /* 1000BASE-T Control Register */
599 #define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
600 #define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
601 #define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
602 /* 0=Configure PHY as Slave */
603 #define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
604 /* 0=Automatic Master/Slave config */
606 /* 1000BASE-T Status Register */
607 #define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
608 #define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
611 /* PHY 1000 MII Register/Bit Definitions */
612 /* PHY Registers defined by IEEE */
613 #define PHY_CONTROL 0x00 /* Control Register */
614 #define PHY_STATUS 0x01 /* Status Register */
615 #define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
616 #define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
617 #define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
618 #define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
619 #define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
620 #define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
623 #define E1000_EECD_SK 0x00000001 /* NVM Clock */
624 #define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
625 #define E1000_EECD_DI 0x00000004 /* NVM Data In */
626 #define E1000_EECD_DO 0x00000008 /* NVM Data Out */
627 #define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
628 #define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
629 #define E1000_EECD_PRES 0x00000100 /* NVM Present */
630 /* NVM Addressing bits based on type 0=small, 1=large */
631 #define E1000_EECD_ADDR_BITS 0x00000400
632 #define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */
633 #define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */
634 #define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */
635 #define E1000_EECD_SIZE_EX_SHIFT 11
636 #define E1000_EECD_FLUPD_I210 0x00800000 /* Update FLASH */
637 #define E1000_EECD_FLUDONE_I210 0x04000000 /* Update FLASH done*/
638 #define E1000_EECD_FLASH_DETECTED_I210 0x00080000 /* FLASH detected */
639 #define E1000_FLUDONE_ATTEMPTS 20000
640 #define E1000_EERD_EEWR_MAX_COUNT 512 /* buffered EEPROM words rw */
641 #define E1000_I210_FIFO_SEL_RX 0x00
642 #define E1000_I210_FIFO_SEL_TX_QAV(_i) (0x02 + (_i))
643 #define E1000_I210_FIFO_SEL_TX_LEGACY E1000_I210_FIFO_SEL_TX_QAV(0)
644 #define E1000_I210_FIFO_SEL_BMC2OS_TX 0x06
645 #define E1000_I210_FIFO_SEL_BMC2OS_RX 0x01
646 #define E1000_I210_FLASH_SECTOR_SIZE 0x1000 /* 4KB FLASH sector unit size */
647 /* Secure FLASH mode requires removing MSb */
648 #define E1000_I210_FW_PTR_MASK 0x7FFF
649 /* Firmware code revision field word offset*/
650 #define E1000_I210_FW_VER_OFFSET 328
651 #define E1000_EECD_FLUPD_I210 0x00800000 /* Update FLASH */
652 #define E1000_EECD_FLUDONE_I210 0x04000000 /* Update FLASH done*/
653 #define E1000_FLUDONE_ATTEMPTS 20000
654 #define E1000_EERD_EEWR_MAX_COUNT 512 /* buffered EEPROM words rw */
655 #define E1000_I210_FIFO_SEL_RX 0x00
656 #define E1000_I210_FIFO_SEL_TX_QAV(_i) (0x02 + (_i))
657 #define E1000_I210_FIFO_SEL_TX_LEGACY E1000_I210_FIFO_SEL_TX_QAV(0)
658 #define E1000_I210_FIFO_SEL_BMC2OS_TX 0x06
659 #define E1000_I210_FIFO_SEL_BMC2OS_RX 0x01
662 /* Offset to data in NVM read/write registers */
663 #define E1000_NVM_RW_REG_DATA 16
664 #define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
665 #define E1000_NVM_RW_REG_START 1 /* Start operation */
666 #define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
667 #define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */
669 /* NVM Word Offsets */
670 #define NVM_COMPAT 0x0003
671 #define NVM_ID_LED_SETTINGS 0x0004 /* SERDES output amplitude */
672 #define NVM_VERSION 0x0005
673 #define NVM_INIT_CONTROL2_REG 0x000F
674 #define NVM_INIT_CONTROL3_PORT_B 0x0014
675 #define NVM_INIT_CONTROL3_PORT_A 0x0024
676 #define NVM_ALT_MAC_ADDR_PTR 0x0037
677 #define NVM_CHECKSUM_REG 0x003F
678 #define NVM_COMPATIBILITY_REG_3 0x0003
679 #define NVM_COMPATIBILITY_BIT_MASK 0x8000
680 #define NVM_MAC_ADDR 0x0000
681 #define NVM_SUB_DEV_ID 0x000B
682 #define NVM_SUB_VEN_ID 0x000C
683 #define NVM_DEV_ID 0x000D
684 #define NVM_VEN_ID 0x000E
685 #define NVM_INIT_CTRL_2 0x000F
686 #define NVM_INIT_CTRL_4 0x0013
687 #define NVM_LED_1_CFG 0x001C
688 #define NVM_LED_0_2_CFG 0x001F
689 #define NVM_ETRACK_WORD 0x0042
690 #define NVM_ETRACK_HIWORD 0x0043
691 #define NVM_COMB_VER_OFF 0x0083
692 #define NVM_COMB_VER_PTR 0x003d
694 /* NVM version defines */
695 #define NVM_MAJOR_MASK 0xF000
696 #define NVM_MINOR_MASK 0x0FF0
697 #define NVM_IMAGE_ID_MASK 0x000F
698 #define NVM_COMB_VER_MASK 0x00FF
699 #define NVM_MAJOR_SHIFT 12
700 #define NVM_MINOR_SHIFT 4
701 #define NVM_COMB_VER_SHFT 8
702 #define NVM_VER_INVALID 0xFFFF
703 #define NVM_ETRACK_SHIFT 16
704 #define NVM_ETRACK_VALID 0x8000
705 #define NVM_NEW_DEC_MASK 0x0F00
706 #define NVM_HEX_CONV 16
707 #define NVM_HEX_TENS 10
709 #define NVM_ETS_CFG 0x003E
710 #define NVM_ETS_LTHRES_DELTA_MASK 0x07C0
711 #define NVM_ETS_LTHRES_DELTA_SHIFT 6
712 #define NVM_ETS_TYPE_MASK 0x0038
713 #define NVM_ETS_TYPE_SHIFT 3
714 #define NVM_ETS_TYPE_EMC 0x000
715 #define NVM_ETS_NUM_SENSORS_MASK 0x0007
716 #define NVM_ETS_DATA_LOC_MASK 0x3C00
717 #define NVM_ETS_DATA_LOC_SHIFT 10
718 #define NVM_ETS_DATA_INDEX_MASK 0x0300
719 #define NVM_ETS_DATA_INDEX_SHIFT 8
720 #define NVM_ETS_DATA_HTHRESH_MASK 0x00FF
722 #define E1000_NVM_CFG_DONE_PORT_0 0x040000 /* MNG config cycle done */
723 #define E1000_NVM_CFG_DONE_PORT_1 0x080000 /* ...for second port */
724 #define E1000_NVM_CFG_DONE_PORT_2 0x100000 /* ...for third port */
725 #define E1000_NVM_CFG_DONE_PORT_3 0x200000 /* ...for fourth port */
727 #define NVM_82580_LAN_FUNC_OFFSET(a) (a ? (0x40 + (0x40 * a)) : 0)
729 /* Mask bits for fields in Word 0x24 of the NVM */
730 #define NVM_WORD24_COM_MDIO 0x0008 /* MDIO interface shared */
731 #define NVM_WORD24_EXT_MDIO 0x0004 /* MDIO accesses routed external */
733 /* Mask bits for fields in Word 0x0f of the NVM */
734 #define NVM_WORD0F_PAUSE_MASK 0x3000
735 #define NVM_WORD0F_ASM_DIR 0x2000
737 /* Mask bits for fields in Word 0x1a of the NVM */
739 /* length of string needed to store part num */
740 #define E1000_PBANUM_LENGTH 11
742 /* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
743 #define NVM_SUM 0xBABA
745 #define NVM_PBA_OFFSET_0 8
746 #define NVM_PBA_OFFSET_1 9
747 #define NVM_RESERVED_WORD 0xFFFF
748 #define NVM_PBA_PTR_GUARD 0xFAFA
749 #define NVM_WORD_SIZE_BASE_SHIFT 6
751 /* NVM Commands - Microwire */
753 /* NVM Commands - SPI */
754 #define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
755 #define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */
756 #define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */
757 #define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
758 #define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */
759 #define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */
761 /* SPI NVM Status Register */
762 #define NVM_STATUS_RDY_SPI 0x01
764 /* Word definitions for ID LED Settings */
765 #define ID_LED_RESERVED_0000 0x0000
766 #define ID_LED_RESERVED_FFFF 0xFFFF
767 #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
768 (ID_LED_OFF1_OFF2 << 8) | \
769 (ID_LED_DEF1_DEF2 << 4) | \
771 #define ID_LED_DEF1_DEF2 0x1
772 #define ID_LED_DEF1_ON2 0x2
773 #define ID_LED_DEF1_OFF2 0x3
774 #define ID_LED_ON1_DEF2 0x4
775 #define ID_LED_ON1_ON2 0x5
776 #define ID_LED_ON1_OFF2 0x6
777 #define ID_LED_OFF1_DEF2 0x7
778 #define ID_LED_OFF1_ON2 0x8
779 #define ID_LED_OFF1_OFF2 0x9
781 #define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
782 #define IGP_ACTIVITY_LED_ENABLE 0x0300
783 #define IGP_LED3_MODE 0x07000000
785 /* PCI/PCI-X/PCI-EX Config space */
786 #define PCIE_DEVICE_CONTROL2 0x28
787 #define PCIE_DEVICE_CONTROL2_16ms 0x0005
789 #define PHY_REVISION_MASK 0xFFFFFFF0
790 #define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
791 #define MAX_PHY_MULTI_PAGE_REG 0xF
793 /* Bit definitions for valid PHY IDs. */
797 #define M88E1111_I_PHY_ID 0x01410CC0
798 #define M88E1112_E_PHY_ID 0x01410C90
799 #define I347AT4_E_PHY_ID 0x01410DC0
800 #define IGP03E1000_E_PHY_ID 0x02A80390
801 #define I82580_I_PHY_ID 0x015403A0
802 #define I350_I_PHY_ID 0x015403B0
803 #define M88_VENDOR 0x0141
804 #define I210_I_PHY_ID 0x01410C00
805 #define M88E1543_E_PHY_ID 0x01410EA0
807 /* M88E1000 Specific Registers */
808 #define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
809 #define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
810 #define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
812 #define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
813 #define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
815 /* M88E1000 PHY Specific Control Register */
816 #define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
817 /* 1=CLK125 low, 0=CLK125 toggling */
818 #define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
819 /* Manual MDI configuration */
820 #define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
821 /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
822 #define M88E1000_PSCR_AUTO_X_1000T 0x0040
823 /* Auto crossover enabled all speeds */
824 #define M88E1000_PSCR_AUTO_X_MODE 0x0060
825 /* 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold
826 * 0=Normal 10BASE-T Rx Threshold
828 /* 1=5-bit interface in 100BASE-TX, 0=MII interface in 100BASE-TX */
829 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
831 /* M88E1000 PHY Specific Status Register */
832 #define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
833 #define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
834 #define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
841 #define M88E1000_PSSR_CABLE_LENGTH 0x0380
842 #define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
843 #define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
845 #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
847 /* M88E1000 Extended PHY Specific Control Register */
848 /* 1 = Lost lock detect enabled.
849 * Will assert lost lock and bring
850 * link down if idle not seen
851 * within 1ms in 1000BASE-T
853 /* Number of times we will attempt to autonegotiate before downshifting if we
856 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
857 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
858 /* Number of times we will attempt to autonegotiate before downshifting if we
861 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
862 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
863 #define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
865 /* Intel i347-AT4 Registers */
867 #define I347AT4_PCDL 0x10 /* PHY Cable Diagnostics Length */
868 #define I347AT4_PCDC 0x15 /* PHY Cable Diagnostics Control */
869 #define I347AT4_PAGE_SELECT 0x16
871 /* i347-AT4 Extended PHY Specific Control Register */
873 /* Number of times we will attempt to autonegotiate before downshifting if we
876 #define I347AT4_PSCR_DOWNSHIFT_ENABLE 0x0800
877 #define I347AT4_PSCR_DOWNSHIFT_MASK 0x7000
878 #define I347AT4_PSCR_DOWNSHIFT_1X 0x0000
879 #define I347AT4_PSCR_DOWNSHIFT_2X 0x1000
880 #define I347AT4_PSCR_DOWNSHIFT_3X 0x2000
881 #define I347AT4_PSCR_DOWNSHIFT_4X 0x3000
882 #define I347AT4_PSCR_DOWNSHIFT_5X 0x4000
883 #define I347AT4_PSCR_DOWNSHIFT_6X 0x5000
884 #define I347AT4_PSCR_DOWNSHIFT_7X 0x6000
885 #define I347AT4_PSCR_DOWNSHIFT_8X 0x7000
887 /* i347-AT4 PHY Cable Diagnostics Control */
888 #define I347AT4_PCDC_CABLE_LENGTH_UNIT 0x0400 /* 0=cm 1=meters */
890 /* Marvell 1112 only registers */
891 #define M88E1112_VCT_DSP_DISTANCE 0x001A
893 /* M88EC018 Rev 2 specific DownShift settings */
894 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
895 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
898 #define E1000_MDIC_DATA_MASK 0x0000FFFF
899 #define E1000_MDIC_REG_MASK 0x001F0000
900 #define E1000_MDIC_REG_SHIFT 16
901 #define E1000_MDIC_PHY_MASK 0x03E00000
902 #define E1000_MDIC_PHY_SHIFT 21
903 #define E1000_MDIC_OP_WRITE 0x04000000
904 #define E1000_MDIC_OP_READ 0x08000000
905 #define E1000_MDIC_READY 0x10000000
906 #define E1000_MDIC_INT_EN 0x20000000
907 #define E1000_MDIC_ERROR 0x40000000
908 #define E1000_MDIC_DEST 0x80000000
911 #define E1000_THSTAT_PWR_DOWN 0x00000001 /* Power Down Event */
912 #define E1000_THSTAT_LINK_THROTTLE 0x00000002 /* Link Speed Throttle Event */
914 /* Energy Efficient Ethernet */
915 #define E1000_IPCNFG_EEE_1G_AN 0x00000008 /* EEE Enable 1G AN */
916 #define E1000_IPCNFG_EEE_100M_AN 0x00000004 /* EEE Enable 100M AN */
917 #define E1000_EEER_TX_LPI_EN 0x00010000 /* EEE Tx LPI Enable */
918 #define E1000_EEER_RX_LPI_EN 0x00020000 /* EEE Rx LPI Enable */
919 #define E1000_EEER_FRC_AN 0x10000000 /* Enable EEE in loopback */
920 #define E1000_EEER_LPI_FC 0x00040000 /* EEE Enable on FC */
921 #define E1000_EEE_SU_LPI_CLK_STP 0X00800000 /* EEE LPI Clock Stop */
922 #define E1000_EEER_EEE_NEG 0x20000000 /* EEE capability nego */
923 #define E1000_EEE_LP_ADV_ADDR_I350 0x040F /* EEE LP Advertisement */
924 #define E1000_EEE_LP_ADV_DEV_I210 7 /* EEE LP Adv Device */
925 #define E1000_EEE_LP_ADV_ADDR_I210 61 /* EEE LP Adv Register */
926 #define E1000_MMDAC_FUNC_DATA 0x4000 /* Data, no post increment */
927 #define E1000_M88E1543_PAGE_ADDR 0x16 /* Page Offset Register */
928 #define E1000_M88E1543_EEE_CTRL_1 0x0
929 #define E1000_M88E1543_EEE_CTRL_1_MS 0x0001 /* EEE Master/Slave */
930 #define E1000_EEE_ADV_DEV_I354 7
931 #define E1000_EEE_ADV_ADDR_I354 60
932 #define E1000_EEE_ADV_100_SUPPORTED (1 << 1) /* 100BaseTx EEE Supported */
933 #define E1000_EEE_ADV_1000_SUPPORTED (1 << 2) /* 1000BaseT EEE Supported */
934 #define E1000_PCS_STATUS_DEV_I354 3
935 #define E1000_PCS_STATUS_ADDR_I354 1
936 #define E1000_PCS_STATUS_TX_LPI_IND 0x0200 /* Tx in LPI state */
937 #define E1000_PCS_STATUS_RX_LPI_RCVD 0x0400
938 #define E1000_PCS_STATUS_TX_LPI_RCVD 0x0800
941 #define E1000_GEN_CTL_READY 0x80000000
942 #define E1000_GEN_CTL_ADDRESS_SHIFT 8
943 #define E1000_GEN_POLL_TIMEOUT 640
945 #define E1000_VFTA_ENTRY_SHIFT 5
946 #define E1000_VFTA_ENTRY_MASK 0x7F
947 #define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F
949 /* DMA Coalescing register fields */
950 #define E1000_PCIEMISC_LX_DECISION 0x00000080 /* Lx power decision based
953 /* Tx Rate-Scheduler Config fields */
954 #define E1000_RTTBCNRC_RS_ENA 0x80000000
955 #define E1000_RTTBCNRC_RF_DEC_MASK 0x00003FFF
956 #define E1000_RTTBCNRC_RF_INT_SHIFT 14
957 #define E1000_RTTBCNRC_RF_INT_MASK \
958 (E1000_RTTBCNRC_RF_DEC_MASK << E1000_RTTBCNRC_RF_INT_SHIFT)
projects / cascardo / linux.git / blob