drivers/net/phy/micrel.c

   1 /*
   2  * drivers/net/phy/micrel.c
   3  *
   4  * Driver for Micrel PHYs
   5  *
   6  * Author: David J. Choi
   7  *
   8  * Copyright (c) 2010 Micrel, Inc.
   9  *
  10  * This program is free software; you can redistribute  it and/or modify it
  11  * under  the terms of  the GNU General  Public License as published by the
  12  * Free Software Foundation;  either version 2 of the  License, or (at your
  13  * option) any later version.
  14  *
  15  * Support : ksz9021 1000/100/10 phy from Micrel
  16  *              ks8001, ks8737, ks8721, ks8041, ks8051 100/10 phy
  17  */
  18
  19 #include <linux/kernel.h>
  20 #include <linux/module.h>
  21 #include <linux/phy.h>
  22 #include <linux/micrel_phy.h>
  23
  24 /* Operation Mode Strap Override */
  25 #define MII_KSZPHY_OMSO                         0x16
  26 #define KSZPHY_OMSO_B_CAST_OFF                  (1 << 9)
  27 #define KSZPHY_OMSO_RMII_OVERRIDE               (1 << 1)
  28 #define KSZPHY_OMSO_MII_OVERRIDE                (1 << 0)
  29
  30 /* general Interrupt control/status reg in vendor specific block. */
  31 #define MII_KSZPHY_INTCS                        0x1B
  32 #define KSZPHY_INTCS_JABBER                     (1 << 15)
  33 #define KSZPHY_INTCS_RECEIVE_ERR                (1 << 14)
  34 #define KSZPHY_INTCS_PAGE_RECEIVE               (1 << 13)
  35 #define KSZPHY_INTCS_PARELLEL                   (1 << 12)
  36 #define KSZPHY_INTCS_LINK_PARTNER_ACK           (1 << 11)
  37 #define KSZPHY_INTCS_LINK_DOWN                  (1 << 10)
  38 #define KSZPHY_INTCS_REMOTE_FAULT               (1 << 9)
  39 #define KSZPHY_INTCS_LINK_UP                    (1 << 8)
  40 #define KSZPHY_INTCS_ALL                        (KSZPHY_INTCS_LINK_UP |\
  41                                                 KSZPHY_INTCS_LINK_DOWN)
  42
  43 /* general PHY control reg in vendor specific block. */
  44 #define MII_KSZPHY_CTRL                 0x1F
  45 /* bitmap of PHY register to set interrupt mode */
  46 #define KSZPHY_CTRL_INT_ACTIVE_HIGH             (1 << 9)
  47 #define KSZ9021_CTRL_INT_ACTIVE_HIGH            (1 << 14)
  48 #define KS8737_CTRL_INT_ACTIVE_HIGH             (1 << 14)
  49 #define KSZ8051_RMII_50MHZ_CLK                  (1 << 7)
  50
  51 static int kszphy_ack_interrupt(struct phy_device *phydev)
  52 {
  53         /* bit[7..0] int status, which is a read and clear register. */
  54         int rc;
  55
  56         rc = phy_read(phydev, MII_KSZPHY_INTCS);
  57
  58         return (rc < 0) ? rc : 0;
  59 }
  60
  61 static int kszphy_set_interrupt(struct phy_device *phydev)
  62 {
  63         int temp;
  64         temp = (PHY_INTERRUPT_ENABLED == phydev->interrupts) ?
  65                 KSZPHY_INTCS_ALL : 0;
  66         return phy_write(phydev, MII_KSZPHY_INTCS, temp);
  67 }
  68
  69 static int kszphy_config_intr(struct phy_device *phydev)
  70 {
  71         int temp, rc;
  72
  73         /* set the interrupt pin active low */
  74         temp = phy_read(phydev, MII_KSZPHY_CTRL);
  75         temp &= ~KSZPHY_CTRL_INT_ACTIVE_HIGH;
  76         phy_write(phydev, MII_KSZPHY_CTRL, temp);
  77         rc = kszphy_set_interrupt(phydev);
  78         return rc < 0 ? rc : 0;
  79 }
  80
  81 static int ksz9021_config_intr(struct phy_device *phydev)
  82 {
  83         int temp, rc;
  84
  85         /* set the interrupt pin active low */
  86         temp = phy_read(phydev, MII_KSZPHY_CTRL);
  87         temp &= ~KSZ9021_CTRL_INT_ACTIVE_HIGH;
  88         phy_write(phydev, MII_KSZPHY_CTRL, temp);
  89         rc = kszphy_set_interrupt(phydev);
  90         return rc < 0 ? rc : 0;
  91 }
  92
  93 static int ks8737_config_intr(struct phy_device *phydev)
  94 {
  95         int temp, rc;
  96
  97         /* set the interrupt pin active low */
  98         temp = phy_read(phydev, MII_KSZPHY_CTRL);
  99         temp &= ~KS8737_CTRL_INT_ACTIVE_HIGH;
 100         phy_write(phydev, MII_KSZPHY_CTRL, temp);
 101         rc = kszphy_set_interrupt(phydev);
 102         return rc < 0 ? rc : 0;
 103 }
 104
 105 static int kszphy_config_init(struct phy_device *phydev)
 106 {
 107         return 0;
 108 }
 109
 110 static int ksz8021_config_init(struct phy_device *phydev)
 111 {
 112         const u16 val = KSZPHY_OMSO_B_CAST_OFF | KSZPHY_OMSO_RMII_OVERRIDE;
 113         phy_write(phydev, MII_KSZPHY_OMSO, val);
 114         return 0;
 115 }
 116
 117 static int ks8051_config_init(struct phy_device *phydev)
 118 {
 119         int regval;
 120
 121         if (phydev->dev_flags & MICREL_PHY_50MHZ_CLK) {
 122                 regval = phy_read(phydev, MII_KSZPHY_CTRL);
 123                 regval |= KSZ8051_RMII_50MHZ_CLK;
 124                 phy_write(phydev, MII_KSZPHY_CTRL, regval);
 125         }
 126
 127         return 0;
 128 }
 129
 130 static struct phy_driver ksphy_driver[] = {
 131 {
 132         .phy_id         = PHY_ID_KS8737,
 133         .phy_id_mask    = 0x00fffff0,
 134         .name           = "Micrel KS8737",
 135         .features       = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
 136         .flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 137         .config_init    = kszphy_config_init,
 138         .config_aneg    = genphy_config_aneg,
 139         .read_status    = genphy_read_status,
 140         .ack_interrupt  = kszphy_ack_interrupt,
 141         .config_intr    = ks8737_config_intr,
 142         .driver         = { .owner = THIS_MODULE,},
 143 }, {
 144         .phy_id         = PHY_ID_KSZ8021,
 145         .phy_id_mask    = 0x00ffffff,
 146         .name           = "Micrel KSZ8021",
 147         .features       = (PHY_BASIC_FEATURES | SUPPORTED_Pause |
 148                            SUPPORTED_Asym_Pause),
 149         .flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 150         .config_init    = ksz8021_config_init,
 151         .config_aneg    = genphy_config_aneg,
 152         .read_status    = genphy_read_status,
 153         .ack_interrupt  = kszphy_ack_interrupt,
 154         .config_intr    = kszphy_config_intr,
 155         .driver         = { .owner = THIS_MODULE,},
 156 }, {
 157         .phy_id         = PHY_ID_KSZ8041,
 158         .phy_id_mask    = 0x00fffff0,
 159         .name           = "Micrel KSZ8041",
 160         .features       = (PHY_BASIC_FEATURES | SUPPORTED_Pause
 161                                 | SUPPORTED_Asym_Pause),
 162         .flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 163         .config_init    = kszphy_config_init,
 164         .config_aneg    = genphy_config_aneg,
 165         .read_status    = genphy_read_status,
 166         .ack_interrupt  = kszphy_ack_interrupt,
 167         .config_intr    = kszphy_config_intr,
 168         .driver         = { .owner = THIS_MODULE,},
 169 }, {
 170         .phy_id         = PHY_ID_KSZ8051,
 171         .phy_id_mask    = 0x00fffff0,
 172         .name           = "Micrel KSZ8051",
 173         .features       = (PHY_BASIC_FEATURES | SUPPORTED_Pause
 174                                 | SUPPORTED_Asym_Pause),
 175         .flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 176         .config_init    = ks8051_config_init,
 177         .config_aneg    = genphy_config_aneg,
 178         .read_status    = genphy_read_status,
 179         .ack_interrupt  = kszphy_ack_interrupt,
 180         .config_intr    = kszphy_config_intr,
 181         .driver         = { .owner = THIS_MODULE,},
 182 }, {
 183         .phy_id         = PHY_ID_KSZ8001,
 184         .name           = "Micrel KSZ8001 or KS8721",
 185         .phy_id_mask    = 0x00ffffff,
 186         .features       = (PHY_BASIC_FEATURES | SUPPORTED_Pause),
 187         .flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 188         .config_init    = kszphy_config_init,
 189         .config_aneg    = genphy_config_aneg,
 190         .read_status    = genphy_read_status,
 191         .ack_interrupt  = kszphy_ack_interrupt,
 192         .config_intr    = kszphy_config_intr,
 193         .driver         = { .owner = THIS_MODULE,},
 194 }, {
 195         .phy_id         = PHY_ID_KSZ9021,
 196         .phy_id_mask    = 0x000ffffe,
 197         .name           = "Micrel KSZ9021 Gigabit PHY",
 198         .features       = (PHY_GBIT_FEATURES | SUPPORTED_Pause
 199                                 | SUPPORTED_Asym_Pause),
 200         .flags          = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
 201         .config_init    = kszphy_config_init,
 202         .config_aneg    = genphy_config_aneg,
 203         .read_status    = genphy_read_status,
 204         .ack_interrupt  = kszphy_ack_interrupt,
 205         .config_intr    = ksz9021_config_intr,
 206         .driver         = { .owner = THIS_MODULE, },
 207 } };
 208
 209 static int __init ksphy_init(void)
 210 {
 211         return phy_drivers_register(ksphy_driver,
 212                 ARRAY_SIZE(ksphy_driver));
 213 }
 214
 215 static void __exit ksphy_exit(void)
 216 {
 217         phy_drivers_unregister(ksphy_driver,
 218                 ARRAY_SIZE(ksphy_driver));
 219 }
 220
 221 module_init(ksphy_init);
 222 module_exit(ksphy_exit);
 223
 224 MODULE_DESCRIPTION("Micrel PHY driver");
 225 MODULE_AUTHOR("David J. Choi");
 226 MODULE_LICENSE("GPL");
 227
 228 static struct mdio_device_id __maybe_unused micrel_tbl[] = {
 229         { PHY_ID_KSZ9021, 0x000ffffe },
 230         { PHY_ID_KSZ8001, 0x00ffffff },
 231         { PHY_ID_KS8737, 0x00fffff0 },
 232         { PHY_ID_KSZ8021, 0x00ffffff },
 233         { PHY_ID_KSZ8041, 0x00fffff0 },
 234         { PHY_ID_KSZ8051, 0x00fffff0 },
 235         { }
 236 };
 237
 238 MODULE_DEVICE_TABLE(mdio, micrel_tbl);