+static void rt2x00queue_create_tx_descriptor_ht(struct rt2x00_dev *rt2x00dev,
+ struct sk_buff *skb,
+ struct txentry_desc *txdesc,
+ const struct rt2x00_rate *hwrate)
+{
+ struct ieee80211_tx_info *tx_info = IEEE80211_SKB_CB(skb);
+ struct ieee80211_tx_rate *txrate = &tx_info->control.rates[0];
+ struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data;
+
+ if (tx_info->control.sta)
+ txdesc->u.ht.mpdu_density =
+ tx_info->control.sta->ht_cap.ampdu_density;
+
+ txdesc->u.ht.ba_size = 7; /* FIXME: What value is needed? */
+
+ /*
+ * Only one STBC stream is supported for now.
+ */
+ if (tx_info->flags & IEEE80211_TX_CTL_STBC)
+ txdesc->u.ht.stbc = 1;
+
+ /*
+ * If IEEE80211_TX_RC_MCS is set txrate->idx just contains the
+ * mcs rate to be used
+ */
+ if (txrate->flags & IEEE80211_TX_RC_MCS) {
+ txdesc->u.ht.mcs = txrate->idx;
+
+ /*
+ * MIMO PS should be set to 1 for STA's using dynamic SM PS
+ * when using more then one tx stream (>MCS7).
+ */
+ if (tx_info->control.sta && txdesc->u.ht.mcs > 7 &&
+ ((tx_info->control.sta->ht_cap.cap &
+ IEEE80211_HT_CAP_SM_PS) >>
+ IEEE80211_HT_CAP_SM_PS_SHIFT) ==
+ WLAN_HT_CAP_SM_PS_DYNAMIC)
+ __set_bit(ENTRY_TXD_HT_MIMO_PS, &txdesc->flags);
+ } else {
+ txdesc->u.ht.mcs = rt2x00_get_rate_mcs(hwrate->mcs);
+ if (txrate->flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE)
+ txdesc->u.ht.mcs |= 0x08;
+ }
+
+ /*
+ * This frame is eligible for an AMPDU, however, don't aggregate
+ * frames that are intended to probe a specific tx rate.
+ */
+ if (tx_info->flags & IEEE80211_TX_CTL_AMPDU &&
+ !(tx_info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE))
+ __set_bit(ENTRY_TXD_HT_AMPDU, &txdesc->flags);
+
+ /*
+ * Set 40Mhz mode if necessary (for legacy rates this will
+ * duplicate the frame to both channels).
+ */
+ if (txrate->flags & IEEE80211_TX_RC_40_MHZ_WIDTH ||
+ txrate->flags & IEEE80211_TX_RC_DUP_DATA)
+ __set_bit(ENTRY_TXD_HT_BW_40, &txdesc->flags);
+ if (txrate->flags & IEEE80211_TX_RC_SHORT_GI)
+ __set_bit(ENTRY_TXD_HT_SHORT_GI, &txdesc->flags);
+
+ /*
+ * Determine IFS values
+ * - Use TXOP_BACKOFF for management frames except beacons
+ * - Use TXOP_SIFS for fragment bursts
+ * - Use TXOP_HTTXOP for everything else
+ *
+ * Note: rt2800 devices won't use CTS protection (if used)
+ * for frames not transmitted with TXOP_HTTXOP
+ */
+ if (ieee80211_is_mgmt(hdr->frame_control) &&
+ !ieee80211_is_beacon(hdr->frame_control))
+ txdesc->u.ht.txop = TXOP_BACKOFF;
+ else if (!(tx_info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT))
+ txdesc->u.ht.txop = TXOP_SIFS;
+ else
+ txdesc->u.ht.txop = TXOP_HTTXOP;
+}
+
+static void rt2x00queue_create_tx_descriptor(struct rt2x00_dev *rt2x00dev,
+ struct sk_buff *skb,