+/**
+ * tps65090_reg_set_overcurrent_wait - Setup overcurrent wait
+ *
+ * This will set the overcurrent wait time based on what's in the regulator
+ * info.
+ *
+ * @ri: Overall regulator data
+ * @rdev: Regulator device
+ *
+ * Return: 0 if no error, non-zero if there was an error writing the register.
+ */
+static int tps65090_reg_set_overcurrent_wait(struct tps65090_regulator *ri,
+ struct regulator_dev *rdev)
+{
+ int ret;
+
+ ret = regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+ MAX_OVERCURRENT_WAIT << CTRL_WT_BIT,
+ ri->overcurrent_wait << CTRL_WT_BIT);
+ if (ret) {
+ dev_err(&rdev->dev, "Error updating overcurrent wait %#x\n",
+ rdev->desc->enable_reg);
+ }
+
+ return ret;
+}
+
+/**
+ * tps65090_try_enable_fet - Try to enable a FET
+ *
+ * @rdev: Regulator device
+ *
+ * Return: 0 if ok, -ENOTRECOVERABLE if the FET power good bit did not get
+ * set, or some other -ve value if another error occurred (e.g. i2c error)
+ */
+static int tps65090_try_enable_fet(struct regulator_dev *rdev)
+{
+ unsigned int control;
+ int ret, i;
+
+ ret = regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+ rdev->desc->enable_mask,
+ rdev->desc->enable_mask);
+ if (ret < 0) {
+ dev_err(&rdev->dev, "Error in updating reg %#x\n",
+ rdev->desc->enable_reg);
+ return ret;
+ }
+
+ for (i = 0; i < MAX_CTRL_READ_TRIES; i++) {
+ ret = regmap_read(rdev->regmap, rdev->desc->enable_reg,
+ &control);
+ if (ret < 0)
+ return ret;
+
+ if (!(control & BIT(CTRL_TO_BIT)))
+ break;
+
+ usleep_range(1000, 1500);
+ }
+ if (!(control & BIT(CTRL_PG_BIT)))
+ return -ENOTRECOVERABLE;
+
+ return 0;
+}
+
+/**
+ * tps65090_fet_enable - Enable a FET, trying a few times if it fails
+ *
+ * Some versions of the tps65090 have issues when turning on the FETs.
+ * This function goes through several steps to ensure the best chance of the
+ * FET going on. Specifically:
+ * - We'll make sure that we bump the "overcurrent wait" to the maximum, which
+ * increases the chances that we'll turn on properly.
+ * - We'll retry turning the FET on multiple times (turning off in between).
+ *
+ * @rdev: Regulator device
+ *
+ * Return: 0 if ok, non-zero if it fails.
+ */
+static int tps65090_fet_enable(struct regulator_dev *rdev)
+{
+ int ret, tries;
+
+ /*
+ * Try enabling multiple times until we succeed since sometimes the
+ * first try times out.
+ */
+ tries = 0;
+ while (true) {
+ ret = tps65090_try_enable_fet(rdev);
+ if (!ret)
+ break;
+ if (ret != -ENOTRECOVERABLE || tries == MAX_FET_ENABLE_TRIES)
+ goto err;
+
+ /* Try turning the FET off (and then on again) */
+ ret = regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+ rdev->desc->enable_mask, 0);
+ if (ret)
+ goto err;
+
+ tries++;
+ }
+
+ if (tries)
+ dev_warn(&rdev->dev, "reg %#x enable ok after %d tries\n",
+ rdev->desc->enable_reg, tries);
+
+ return 0;
+err:
+ dev_warn(&rdev->dev, "reg %#x enable failed\n", rdev->desc->enable_reg);
+ WARN_ON(1);
+
+ return ret;
+}
+
+static struct regulator_ops tps65090_reg_control_ops = {