#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/input.h>
+#include <linux/smc91x.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
-#include <mach/tc.h>
+#include <plat/tc.h>
#include <mach/gpio.h>
-#include <mach/mux.h>
-#include <mach/fpga.h>
-#include <mach/nand.h>
-#include <mach/keypad.h>
-#include <mach/common.h>
-#include <mach/board.h>
+#include <plat/mux.h>
+#include <plat/fpga.h>
+#include <plat/nand.h>
+#include <plat/keypad.h>
+#include <plat/common.h>
+#include <plat/board.h>
/* fsample is pretty close to p2-sample */
0
};
+static struct smc91x_platdata smc91x_info = {
+ .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+ .leda = RPC_LED_100_10,
+ .ledb = RPC_LED_TX_RX,
+};
+
static struct resource smc91x_resources[] = {
[0] = {
.start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
.flags = IORESOURCE_MEM,
},
[1] = {
- .start = INT_730_MPU_EXT_NIRQ,
+ .start = INT_7XX_MPU_EXT_NIRQ,
.end = 0,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
},
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
+ .dev = {
+ .platform_data = &smc91x_info,
+ },
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
static struct resource kp_resources[] = {
[0] = {
- .start = INT_730_MPUIO_KEYPAD,
- .end = INT_730_MPUIO_KEYPAD,
+ .start = INT_7XX_MPUIO_KEYPAD,
+ .end = INT_7XX_MPUIO_KEYPAD,
.flags = IORESOURCE_IRQ,
},
};
/*
* Hold GSM Reset until needed
*/
- omap_writew(omap_readw(OMAP730_DSP_M_CTL) & ~1, OMAP730_DSP_M_CTL);
+ omap_writew(omap_readw(OMAP7XX_DSP_M_CTL) & ~1, OMAP7XX_DSP_M_CTL);
/*
* UARTs -> done automagically by 8250 driver
*/
/* Flash: CS0 timings setup */
- omap_writel(0x0000fff3, OMAP730_FLASH_CFG_0);
- omap_writel(0x00000088, OMAP730_FLASH_ACFG_0);
+ omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_0);
+ omap_writel(0x00000088, OMAP7XX_FLASH_ACFG_0);
/*
* Ethernet support through the debug board
* CS1 timings setup
*/
- omap_writel(0x0000fff3, OMAP730_FLASH_CFG_1);
- omap_writel(0x00000000, OMAP730_FLASH_ACFG_1);
+ omap_writel(0x0000fff3, OMAP7XX_FLASH_CFG_1);
+ omap_writel(0x00000000, OMAP7XX_FLASH_ACFG_1);
/*
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
- omap_writel(omap_readl(OMAP730_IO_CONF_9) & 0x1FFFFFFF, OMAP730_IO_CONF_9);
+ omap_writel(omap_readl(OMAP7XX_IO_CONF_9) & 0x1FFFFFFF, OMAP7XX_IO_CONF_9);
}
MACHINE_START(OMAP_FSAMPLE, "OMAP730 F-Sample")