#include <linux/platform_device.h>
#include <linux/pci.h>
#include <linux/irq.h>
+#include <linux/delay.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/nand.h>
#include <linux/mv643xx_eth.h>
#include <linux/i2c.h>
+#include <linux/serial_reg.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
#include <asm/gpio.h>
/*
* PCI isn't used on the Kuro
*/
- printk(KERN_ERR "kurobox_pro_pci_map_irq failed, unknown bus\n");
-
return -1;
}
static struct mv643xx_eth_platform_data kurobox_pro_eth_data = {
.phy_addr = 8,
- .force_phy_addr = 1,
};
/*****************************************************************************
.n_ports = 2,
};
+/*****************************************************************************
+ * Kurobox Pro specific power off method via UART1-attached microcontroller
+ ****************************************************************************/
+
+#define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2))
+
+static int kurobox_pro_miconread(unsigned char *buf, int count)
+{
+ int i;
+ int timeout;
+
+ for (i = 0; i < count; i++) {
+ timeout = 10;
+
+ while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) {
+ if (--timeout == 0)
+ break;
+ udelay(1000);
+ }
+
+ if (timeout == 0)
+ break;
+ buf[i] = readl(UART1_REG(RX));
+ }
+
+ /* return read bytes */
+ return i;
+}
+
+static int kurobox_pro_miconwrite(const unsigned char *buf, int count)
+{
+ int i = 0;
+
+ while (count--) {
+ while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE))
+ barrier();
+ writel(buf[i++], UART1_REG(TX));
+ }
+
+ return 0;
+}
+
+static int kurobox_pro_miconsend(const unsigned char *data, int count)
+{
+ int i;
+ unsigned char checksum = 0;
+ unsigned char recv_buf[40];
+ unsigned char send_buf[40];
+ unsigned char correct_ack[3];
+ int retry = 2;
+
+ /* Generate checksum */
+ for (i = 0; i < count; i++)
+ checksum -= data[i];
+
+ do {
+ /* Send data */
+ kurobox_pro_miconwrite(data, count);
+
+ /* send checksum */
+ kurobox_pro_miconwrite(&checksum, 1);
+
+ if (kurobox_pro_miconread(recv_buf, sizeof(recv_buf)) <= 3) {
+ printk(KERN_ERR ">%s: receive failed.\n", __func__);
+
+ /* send preamble to clear the receive buffer */
+ memset(&send_buf, 0xff, sizeof(send_buf));
+ kurobox_pro_miconwrite(send_buf, sizeof(send_buf));
+
+ /* make dummy reads */
+ mdelay(100);
+ kurobox_pro_miconread(recv_buf, sizeof(recv_buf));
+ } else {
+ /* Generate expected ack */
+ correct_ack[0] = 0x01;
+ correct_ack[1] = data[1];
+ correct_ack[2] = 0x00;
+
+ /* checksum Check */
+ if ((recv_buf[0] + recv_buf[1] + recv_buf[2] +
+ recv_buf[3]) & 0xFF) {
+ printk(KERN_ERR ">%s: Checksum Error : "
+ "Received data[%02x, %02x, %02x, %02x]"
+ "\n", __func__, recv_buf[0],
+ recv_buf[1], recv_buf[2], recv_buf[3]);
+ } else {
+ /* Check Received Data */
+ if (correct_ack[0] == recv_buf[0] &&
+ correct_ack[1] == recv_buf[1] &&
+ correct_ack[2] == recv_buf[2]) {
+ /* Interval for next command */
+ mdelay(10);
+
+ /* Receive ACK */
+ return 0;
+ }
+ }
+ /* Received NAK or illegal Data */
+ printk(KERN_ERR ">%s: Error : NAK or Illegal Data "
+ "Received\n", __func__);
+ }
+ } while (retry--);
+
+ /* Interval for next command */
+ mdelay(10);
+
+ return -1;
+}
+
+static void kurobox_pro_power_off(void)
+{
+ const unsigned char watchdogkill[] = {0x01, 0x35, 0x00};
+ const unsigned char shutdownwait[] = {0x00, 0x0c};
+ const unsigned char poweroff[] = {0x00, 0x06};
+ /* 38400 baud divisor */
+ const unsigned divisor = ((ORION5X_TCLK + (8 * 38400)) / (16 * 38400));
+
+ pr_info("%s: triggering power-off...\n", __func__);
+
+ /* hijack uart1 and reset into sane state (38400,8n1,even parity) */
+ writel(0x83, UART1_REG(LCR));
+ writel(divisor & 0xff, UART1_REG(DLL));
+ writel((divisor >> 8) & 0xff, UART1_REG(DLM));
+ writel(0x1b, UART1_REG(LCR));
+ writel(0x00, UART1_REG(IER));
+ writel(0x07, UART1_REG(FCR));
+ writel(0x00, UART1_REG(MCR));
+
+ /* Send the commands to shutdown the Kurobox Pro */
+ kurobox_pro_miconsend(watchdogkill, sizeof(watchdogkill)) ;
+ kurobox_pro_miconsend(shutdownwait, sizeof(shutdownwait)) ;
+ kurobox_pro_miconsend(poweroff, sizeof(poweroff));
+}
+
/*****************************************************************************
* General Setup
****************************************************************************/
{ 13, MPP_SATA_LED }, /* SATA 1 presence */
{ 14, MPP_SATA_LED }, /* SATA 0 active */
{ 15, MPP_SATA_LED }, /* SATA 1 active */
- { 16, MPP_UNUSED },
- { 17, MPP_UNUSED },
- { 18, MPP_UNUSED },
- { 19, MPP_UNUSED },
+ { 16, MPP_UART }, /* UART1 RXD */
+ { 17, MPP_UART }, /* UART1 TXD */
+ { 18, MPP_UART }, /* UART1 CTSn */
+ { 19, MPP_UART }, /* UART1 RTSn */
{ -1 },
};
orion5x_i2c_init();
orion5x_sata_init(&kurobox_pro_sata_data);
orion5x_uart0_init();
+ orion5x_uart1_init();
orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE,
KUROBOX_PRO_NOR_BOOT_SIZE);
}
i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1);
+
+ /* register Kurobox Pro specific power-off method */
+ pm_power_off = kurobox_pro_power_off;
}
#ifdef CONFIG_MACH_KUROBOX_PRO
projects / cascardo / linux.git / blobdiff