#include <linux/delay.h>
#include "pci-sh4.h"
-#define INTC_BASE 0xffd00000
-#define INTC_ICR0 (INTC_BASE+0x0)
-#define INTC_ICR1 (INTC_BASE+0x1c)
-#define INTC_INTPRI (INTC_BASE+0x10)
-#define INTC_INTREQ (INTC_BASE+0x24)
-#define INTC_INTMSK0 (INTC_BASE+0x44)
-#define INTC_INTMSK1 (INTC_BASE+0x48)
-#define INTC_INTMSK2 (INTC_BASE+0x40080)
-#define INTC_INTMSKCLR0 (INTC_BASE+0x64)
-#define INTC_INTMSKCLR1 (INTC_BASE+0x68)
-#define INTC_INTMSKCLR2 (INTC_BASE+0x40084)
-#define INTC_INT2MSKR (INTC_BASE+0x40038)
-#define INTC_INT2MSKCR (INTC_BASE+0x4003c)
-
/*
* Initialization. Try all known PCI access methods. Note that we support
* using both PCI BIOS and direct access: in such cases, we use I/O ports
* space mapping) will be called via the platform defined function
* pcibios_init_platform().
*/
-static int __init sh7780_pci_init(void)
+int __init sh7780_pci_init(struct pci_channel *chan)
{
unsigned int id;
- int ret, match = 0;
-
- pr_debug("PCI: Starting intialization.\n");
-
- ctrl_outl(0x00000001, SH7780_PCI_VCR2); /* Enable PCIC */
-
- /* check for SH7780/SH7780R hardware */
- id = pci_read_reg(SH7780_PCIVID);
- if ((id & 0xffff) == SH7780_VENDOR_ID) {
- switch ((id >> 16) & 0xffff) {
- case SH7763_DEVICE_ID:
- case SH7780_DEVICE_ID:
- case SH7781_DEVICE_ID:
- case SH7785_DEVICE_ID:
- match = 1;
- break;
- }
- }
+ const char *type = NULL;
+ int ret;
+
+ printk(KERN_NOTICE "PCI: Starting intialization.\n");
+
+ chan->reg_base = 0xfe040000;
+ chan->io_base = 0xfe200000;
- if (unlikely(!match)) {
- printk(KERN_ERR "PCI: This is not an SH7780 (%x)\n", id);
+ /* Enable CPU access to the PCIC registers. */
+ __raw_writel(PCIECR_ENBL, PCIECR);
+
+ id = __raw_readw(chan->reg_base + SH7780_PCIVID);
+ if (id != SH7780_VENDOR_ID) {
+ printk(KERN_ERR "PCI: Unknown vendor ID 0x%04x.\n", id);
return -ENODEV;
}
- /* Setup the INTC */
- if (mach_is_7780se()) {
- /* ICR0: IRL=use separately */
- ctrl_outl(0x00C00020, INTC_ICR0);
- /* ICR1: detect low level(for 2ndcut) */
- ctrl_outl(0xAAAA0000, INTC_ICR1);
- /* INTPRI: priority=3(all) */
- ctrl_outl(0x33333333, INTC_INTPRI);
+ id = __raw_readw(chan->reg_base + SH7780_PCIDID);
+ type = (id == SH7763_DEVICE_ID) ? "SH7763" :
+ (id == SH7780_DEVICE_ID) ? "SH7780" :
+ (id == SH7781_DEVICE_ID) ? "SH7781" :
+ (id == SH7785_DEVICE_ID) ? "SH7785" :
+ NULL;
+ if (unlikely(!type)) {
+ printk(KERN_ERR "PCI: Found an unsupported Renesas host "
+ "controller, device id 0x%04x.\n", id);
+ return -EINVAL;
}
- if ((ret = sh4_pci_check_direct()) != 0)
+ printk(KERN_NOTICE "PCI: Found a Renesas %s host "
+ "controller, revision %d.\n", type,
+ __raw_readb(chan->reg_base + SH7780_PCIRID));
+
+ if ((ret = sh4_pci_check_direct(chan)) != 0)
return ret;
return pcibios_init_platform();
}
-core_initcall(sh7780_pci_init);
-int __init sh7780_pcic_init(struct sh4_pci_address_map *map)
+int __init sh7780_pcic_init(struct pci_channel *chan,
+ struct sh4_pci_address_map *map)
{
u32 word;
- /*
- * This code is unused for some boards as it is done in the
- * bootloader and doing it here means the MAC addresses loaded
- * by the bootloader get lost.
- */
- if (!(map->flags & SH4_PCIC_NO_RESET)) {
- /* toggle PCI reset pin */
- word = SH4_PCICR_PREFIX | SH4_PCICR_PRST;
- pci_write_reg(word, SH4_PCICR);
- /* Wait for a long time... not 1 sec. but long enough */
- mdelay(100);
- word = SH4_PCICR_PREFIX;
- pci_write_reg(word, SH4_PCICR);
- }
+ __raw_writeb(PCI_CLASS_BRIDGE_HOST >> 8,
+ chan->reg_base + SH7780_PCIBCC);
+ __raw_writeb(PCI_CLASS_BRIDGE_HOST & 0xff,
+ chan->reg_base + SH7780_PCISUB);
/* set the command/status bits to:
* Wait Cycle Control + Parity Enable + Bus Master +
* Mem space enable
*/
- pci_write_reg(0x00000046, SH7780_PCICMD);
-
- /* define this host as the host bridge */
- word = PCI_BASE_CLASS_BRIDGE << 24;
- pci_write_reg(word, SH7780_PCIRID);
+ pci_write_reg(chan, 0x00000046, SH7780_PCICMD);
/* Set IO and Mem windows to local address
* Make PCI and local address the same for easy 1 to 1 mapping
*/
- pci_write_reg(map->window0.size - 0xfffff, SH4_PCILSR0);
- pci_write_reg(map->window1.size - 0xfffff, SH4_PCILSR1);
+ pci_write_reg(chan, map->window0.size - 0xfffff, SH4_PCILSR0);
+ pci_write_reg(chan, map->window1.size - 0xfffff, SH4_PCILSR1);
/* Set the values on window 0 PCI config registers */
- pci_write_reg(map->window0.base, SH4_PCILAR0);
- pci_write_reg(map->window0.base, SH7780_PCIMBAR0);
+ pci_write_reg(chan, map->window0.base, SH4_PCILAR0);
+ pci_write_reg(chan, map->window0.base, SH7780_PCIMBAR0);
/* Set the values on window 1 PCI config registers */
- pci_write_reg(map->window1.base, SH4_PCILAR1);
- pci_write_reg(map->window1.base, SH7780_PCIMBAR1);
-
- /* Map IO space into PCI IO window
- * The IO window is 64K-PCIBIOS_MIN_IO in size
- * IO addresses will be translated to the
- * PCI IO window base address
- */
- pr_debug("PCI: Mapping IO address 0x%x - 0x%x to base 0x%x\n",
- PCIBIOS_MIN_IO, (64 << 10),
- SH7780_PCI_IO_BASE + PCIBIOS_MIN_IO);
-
- /* NOTE: I'm ignoring the PCI error IRQs for now..
- * TODO: add support for the internal error interrupts and
- * DMA interrupts...
- */
+ pci_write_reg(chan, map->window1.base, SH4_PCILAR1);
+ pci_write_reg(chan, map->window1.base, SH7780_PCIMBAR1);
/* Apply any last-minute PCIC fixups */
- pci_fixup_pcic();
+ pci_fixup_pcic(chan);
/* SH7780 init done, set central function init complete */
/* use round robin mode to stop a device starving/overruning */
word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_FTO;
- pci_write_reg(word, SH4_PCICR);
+ pci_write_reg(chan, word, SH4_PCICR);
- return 1;
+ return 0;
}
projects / cascardo / linux.git / blobdiff