Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4

[cascardo/linux.git] / drivers / ieee1394 / Kconfig

diff --git a/drivers/ieee1394/Kconfig b/drivers/ieee1394/Kconfig
index f102fcc..e02096c 100644 (file)
--- a/drivers/ieee1394/Kconfig
+++ b/drivers/ieee1394/Kconfig
@@ -1,8 +1,3 @@
-menu "IEEE 1394 (FireWire) support"
-       depends on PCI || BROKEN
-
-source "drivers/firewire/Kconfig"
-
 config IEEE1394
        tristate "Legacy alternative FireWire driver stack"
        depends on PCI || BROKEN
@@ -16,8 +11,13 @@ config IEEE1394
          is the core support only, you will also need to select a driver for
          your IEEE 1394 adapter.
 
-         To compile this driver as a module, say M here: the
-         module will be called ieee1394.
+         To compile this driver as a module, say M here: the module will be
+         called ieee1394.
+
+         NOTE:
+         ieee1394 is superseded by the newer firewire-core driver.  See
+         http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+         further information on how to switch to the new FireWire drivers.
 
 config IEEE1394_OHCI1394
        tristate "OHCI-1394 controllers"
@@ -29,19 +29,23 @@ config IEEE1394_OHCI1394
          use one of these chipsets.  It should work with any OHCI-1394
          compliant card, however.
 
-         To compile this driver as a module, say M here: the
-         module will be called ohci1394.
+         To compile this driver as a module, say M here: the module will be
+         called ohci1394.
 
          NOTE:
+         ohci1394 is superseded by the newer firewire-ohci driver.  See
+         http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+         further information on how to switch to the new FireWire drivers.
+
          If you want to install firewire-ohci and ohci1394 together, you
          should configure them only as modules and blacklist the driver(s)
          which you don't want to have auto-loaded.  Add either
 
-             blacklist firewire-ohci
-         or
              blacklist ohci1394
              blacklist video1394
              blacklist dv1394
+         or
+             blacklist firewire-ohci
 
          to /etc/modprobe.conf or /etc/modprobe.d/* and update modprobe.conf
          depending on your distribution.
@@ -58,8 +62,8 @@ config IEEE1394_PCILYNX
          Instruments PCILynx chip.  Note: this driver is written for revision
          2 of this chip and may not work with revision 0.
 
-         To compile this driver as a module, say M here: the
-         module will be called pcilynx.
+         To compile this driver as a module, say M here: the module will be
+         called pcilynx.
 
          Only some old and now very rare PCI and CardBus cards and
          PowerMacs G3 B&W contain the PCILynx controller.  Therefore
@@ -79,6 +83,14 @@ config IEEE1394_SBP2
          You should also enable support for disks, CD-ROMs, etc. in the SCSI
          configuration section.
 
+         To compile this driver as a module, say M here: the module will be
+         called sbp2.
+
+         NOTE:
+         sbp2 is superseded by the newer firewire-sbp2 driver. See
+         http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+         further information on how to switch to the new FireWire drivers.
+
 config IEEE1394_SBP2_PHYS_DMA
        bool "Enable replacement for physical DMA in SBP2"
        depends on IEEE1394_SBP2 && VIRT_TO_BUS && EXPERIMENTAL
@@ -111,6 +123,11 @@ config IEEE1394_ETH1394
 
          The module is called eth1394 although it does not emulate Ethernet.
 
+         NOTE:
+         eth1394 is superseded by the newer firewire-net driver. See
+         http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+         further information on how to switch to the new FireWire drivers.
+
 config IEEE1394_RAWIO
        tristate "raw1394 userspace interface"
        depends on IEEE1394
@@ -123,6 +140,11 @@ config IEEE1394_RAWIO
          To compile this driver as a module, say M here: the module will be
          called raw1394.
 
+         NOTE:
+         raw1394 is superseded by the newer firewire-core driver. See
+         http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+         further information on how to switch to the new FireWire drivers.
+
 config IEEE1394_VIDEO1394
        tristate "video1394 userspace interface"
        depends on IEEE1394 && IEEE1394_OHCI1394
@@ -136,13 +158,18 @@ config IEEE1394_VIDEO1394
          To compile this driver as a module, say M here: the module will be
          called video1394.
 
+         NOTE:
+         video1394 is superseded by the newer firewire-core driver. See
+         http://ieee1394.wiki.kernel.org/index.php/Juju_Migration for
+         further information on how to switch to the new FireWire drivers.
+
 config IEEE1394_DV1394
        tristate "dv1394 userspace interface (deprecated)"
        depends on IEEE1394 && IEEE1394_OHCI1394
        help
          The dv1394 driver is unsupported and may be removed from Linux in a
-         future release.  Its functionality is now provided by raw1394 together
-         with libraries such as libiec61883.
+         future release.  Its functionality is now provided by either
+         raw1394 or firewire-core together with libraries such as libiec61883.
 
 config IEEE1394_VERBOSEDEBUG
        bool "Excessive debugging output"
@@ -153,5 +180,3 @@ config IEEE1394_VERBOSEDEBUG
          will quickly result in large amounts of data sent to the system log.
 
          Say Y if you really need the debugging output.  Everyone else says N.
-
-endmenu