*
*/
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
#include <linux/sched.h>
#include <linux/wait.h>
#include <linux/slab.h>
}
-/* Various firmware commands need the list of supported rates, but with
- the hight-bit set for basic rates */
+/*
+ * Various firmware commands need the list of supported rates, but with
+ * the hight-bit set for basic rates
+ */
static int lbs_add_rates(u8 *rates)
{
size_t i;
return ie_len + 2;
}
-/***************************************************************************
+/*
* Set Channel
*/
-/***************************************************************************
+/*
* Scanning
*/
goto done;
}
- /* Validity check: the TLV holds TSF values with 8 bytes each, so
- * the size in the TLV must match the nr_sets value */
+ /*
+ * Validity check: the TLV holds TSF values with 8 bytes each, so
+ * the size in the TLV must match the nr_sets value
+ */
i = get_unaligned_le16(tsfdesc);
tsfdesc += 2;
if (i / 8 != scanresp->nr_sets) {
/* To find out the channel, we must parse the IEs */
ie = pos;
- /* 6+1+8+2+2: size of BSSID, RSSI, time stamp, beacon
- interval, capabilities */
+ /*
+ * 6+1+8+2+2: size of BSSID, RSSI, time stamp, beacon
+ * interval, capabilities
+ */
ielen = left = len - (6 + 1 + 8 + 2 + 2);
while (left >= 2) {
u8 id, elen;
-/***************************************************************************
+/*
* Events
*/
-/***************************************************************************
+/*
* Connect/disconnect
*/
* Set WPA/WPA key material
*/
-/* like "struct cmd_ds_802_11_key_material", but with cmd_header. Once we
- * get rid of WEXT, this should go into host.h */
+/*
+ * like "struct cmd_ds_802_11_key_material", but with cmd_header. Once we
+ * get rid of WEXT, this should go into host.h
+ */
struct cmd_key_material {
struct cmd_header hdr;
sme->ssid, sme->ssid_len,
WLAN_CAPABILITY_ESS, WLAN_CAPABILITY_ESS);
if (!bss) {
- lbs_pr_err("assoc: bss %pM not in scan results\n",
- sme->bssid);
+ wiphy_err(wiphy, "assoc: bss %pM not in scan results\n",
+ sme->bssid);
ret = -ENOENT;
goto done;
}
* we remove all keys like in the WPA/WPA2 setup,
* we just don't set RSN.
*
- * Therefore: fall-throught
+ * Therefore: fall-through
*/
case WLAN_CIPHER_SUITE_TKIP:
case WLAN_CIPHER_SUITE_CCMP:
lbs_enable_rsn(priv, sme->crypto.cipher_group != 0);
break;
default:
- lbs_pr_err("unsupported cipher group 0x%x\n",
- sme->crypto.cipher_group);
+ wiphy_err(wiphy, "unsupported cipher group 0x%x\n",
+ sme->crypto.cipher_group);
ret = -ENOTSUPP;
goto done;
}
params->key, params->key_len);
break;
default:
- lbs_pr_err("unhandled cipher 0x%x\n", params->cipher);
+ wiphy_err(wiphy, "unhandled cipher 0x%x\n", params->cipher);
ret = -ENOTSUPP;
break;
}
}
-/***************************************************************************
+/*
* Get station
*/
-/***************************************************************************
+/*
* "Site survey", here just current channel and noise level
*/
-/***************************************************************************
+/*
* Change interface
*/
-/***************************************************************************
+/*
* IBSS (Ad-Hoc)
*/
-/* The firmware needs the following bits masked out of the beacon-derived
+/*
+ * The firmware needs the following bits masked out of the beacon-derived
* capability field when associating/joining to a BSS:
* 9 (QoS), 11 (APSD), 12 (unused), 14 (unused), 15 (unused)
*/
-/***************************************************************************
+/*
* Initialization
*/
ret = wiphy_register(wdev->wiphy);
if (ret < 0)
- lbs_pr_err("cannot register wiphy device\n");
+ pr_err("cannot register wiphy device\n");
priv->wiphy_registered = true;
ret = register_netdev(priv->dev);
if (ret)
- lbs_pr_err("cannot register network device\n");
+ pr_err("cannot register network device\n");
INIT_DELAYED_WORK(&priv->scan_work, lbs_scan_worker);