-#define AUTOSENSE
#define PSEUDO_DMA
-#define FOO
#define UNSAFE /* Not unsafe for PAS16 -- use it */
#define PDEBUG 0
* Media Vision
* (510) 770-8600
* (800) 348-7116
- *
- * and
- *
- * NCR 5380 Family
- * SCSI Protocol Controller
- * Databook
- *
- * NCR Microelectronics
- * 1635 Aeroplaza Drive
- * Colorado Springs, CO 80916
- * 1+ (719) 578-3400
- * 1+ (800) 334-5454
*/
/*
- * Options :
- * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
- * for commands that return with a CHECK CONDITION status.
- *
- * LIMIT_TRANSFERSIZE - if defined, limit the pseudo-dma transfers to 512
- * bytes at a time. Since interrupts are disabled by default during
- * these transfers, we might need this to give reasonable interrupt
- * service time if the transfer size gets too large.
- *
- * PSEUDO_DMA - enables PSEUDO-DMA hardware, should give a 3-4X performance
- * increase compared to polled I/O.
- *
- * PARITY - enable parity checking. Not supported.
- *
- * SCSI2 - enable support for SCSI-II tagged queueing. Untested.
- *
- * UNSAFE - leave interrupts enabled during pseudo-DMA transfers. This
- * parameter comes from the NCR5380 code. It is NOT unsafe with
- * the PAS16 and you should use it. If you don't you will have
- * a problem with dropped characters during high speed
- * communications during SCSI transfers. If you really don't
- * want to use UNSAFE you can try defining LIMIT_TRANSFERSIZE or
- * twiddle with the transfer size in the high level code.
- *
- * USLEEP - enable support for devices that don't disconnect. Untested.
- *
* The card is detected and initialized in one of several ways :
* 1. Autoprobe (default) - There are many different models of
* the Pro Audio Spectrum/Studio 16, and I only have one of
* If you have problems with your card not being recognized, use
* the LILO command line override. Try to get it recognized without
* interrupts. Ie, for a board at the default 0x388 base port,
- * boot: linux pas16=0x388,255
+ * boot: linux pas16=0x388,0
*
- * SCSI_IRQ_NONE (255) should be specified for no interrupt,
+ * NO_IRQ (0) should be specified for no interrupt,
* IRQ_AUTO (254) to autoprobe for an IRQ line if overridden
* on the command line.
- *
- * (IRQ_AUTO == 254, SCSI_IRQ_NONE == 255 in NCR5380.h)
*/
#include <linux/module.h>
#include <linux/stat.h>
#include <linux/init.h>
-#include "scsi.h"
#include <scsi/scsi_host.h>
#include "pas16.h"
#define AUTOPROBE_IRQ
#include "NCR5380.h"
-static int pas_maxi = 0;
-static int pas_wmaxi = 0;
static unsigned short pas16_addr = 0;
static int pas16_irq = 0;
}
+#ifndef MODULE
/*
* Function : pas16_setup(char *str, int *ints)
*
*
*/
-void __init pas16_setup(char *str, int *ints)
+static int __init pas16_setup(char *str)
{
static int commandline_current = 0;
int i;
+ int ints[10];
+
+ get_options(str, ARRAY_SIZE(ints), ints);
if (ints[0] != 2)
printk("pas16_setup : usage pas16=io_port,irq\n");
else
}
++commandline_current;
}
+ return 1;
}
+__setup("pas16=", pas16_setup);
+#endif
+
/*
* Function : int pas16_detect(struct scsi_host_template * tpnt)
*
*
*/
-int __init pas16_detect(struct scsi_host_template * tpnt)
+static int __init pas16_detect(struct scsi_host_template *tpnt)
{
static int current_override = 0;
static unsigned short current_base = 0;
unsigned short io_port;
int count;
- tpnt->proc_name = "pas16";
- tpnt->show_info = pas16_show_info;
- tpnt->write_info = pas16_write_info;
-
if (pas16_addr != 0) {
overrides[0].io_port = pas16_addr;
/*
else
instance->irq = NCR5380_probe_irq(instance, PAS16_IRQS);
- if (instance->irq != SCSI_IRQ_NONE)
+ /* Compatibility with documented NCR5380 kernel parameters */
+ if (instance->irq == 255)
+ instance->irq = NO_IRQ;
+
+ if (instance->irq != NO_IRQ)
if (request_irq(instance->irq, pas16_intr, 0,
"pas16", instance)) {
printk("scsi%d : IRQ%d not free, interrupts disabled\n",
instance->host_no, instance->irq);
- instance->irq = SCSI_IRQ_NONE;
+ instance->irq = NO_IRQ;
}
- if (instance->irq == SCSI_IRQ_NONE) {
+ if (instance->irq == NO_IRQ) {
printk("scsi%d : interrupts not enabled. for better interactive performance,\n", instance->host_no);
printk("scsi%d : please jumper the board for a free IRQ.\n", instance->host_no);
/* Disable 5380 interrupts, leave drive params the same */
printk("scsi%d : irq = %d\n", instance->host_no, instance->irq);
#endif
- printk("scsi%d : at 0x%04x", instance->host_no, (int)
- instance->io_port);
- if (instance->irq == SCSI_IRQ_NONE)
- printk (" interrupts disabled");
- else
- printk (" irq %d", instance->irq);
- printk(" options CAN_QUEUE=%d CMD_PER_LUN=%d release=%d",
- CAN_QUEUE, CMD_PER_LUN, PAS16_PUBLIC_RELEASE);
- NCR5380_print_options(instance);
- printk("\n");
-
++current_override;
++count;
}
* and matching the H_C_S coordinates to what DOS uses.
*/
-int pas16_biosparam(struct scsi_device *sdev, struct block_device *dev,
- sector_t capacity, int * ip)
+static int pas16_biosparam(struct scsi_device *sdev, struct block_device *dev,
+ sector_t capacity, int *ip)
{
int size = capacity;
ip[0] = 64;
P_DATA_REG_OFFSET);
register int i = len;
int ii = 0;
+ struct NCR5380_hostdata *hostdata = shost_priv(instance);
while ( !(inb(instance->io_port + P_STATUS_REG_OFFSET) & P_ST_RDY) )
++ii;
instance->host_no);
return -1;
}
- if (ii > pas_maxi)
- pas_maxi = ii;
+ if (ii > hostdata->spin_max_r)
+ hostdata->spin_max_r = ii;
return 0;
}
register unsigned short reg = (instance->io_port + P_DATA_REG_OFFSET);
register int i = len;
int ii = 0;
+ struct NCR5380_hostdata *hostdata = shost_priv(instance);
while ( !((inb(instance->io_port + P_STATUS_REG_OFFSET)) & P_ST_RDY) )
++ii;
instance->host_no);
return -1;
}
- if (ii > pas_maxi)
- pas_wmaxi = ii;
+ if (ii > hostdata->spin_max_w)
+ hostdata->spin_max_w = ii;
return 0;
}
static int pas16_release(struct Scsi_Host *shost)
{
- if (shost->irq)
+ if (shost->irq != NO_IRQ)
free_irq(shost->irq, shost);
NCR5380_exit(shost);
if (shost->io_port && shost->n_io_port)
.name = "Pro Audio Spectrum-16 SCSI",
.detect = pas16_detect,
.release = pas16_release,
+ .proc_name = "pas16",
+ .show_info = pas16_show_info,
+ .write_info = pas16_write_info,
+ .info = pas16_info,
.queuecommand = pas16_queue_command,
.eh_abort_handler = pas16_abort,
.eh_bus_reset_handler = pas16_bus_reset,
projects / cascardo / linux.git / blobdiff