#define DRIVER_AUTHOR "Sarah Sharp"
#define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
+#define PORT_WAKE_BITS (PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E)
+
/* Some 0.95 hardware can't handle the chain bit on a Link TRB being cleared */
static int link_quirk;
module_param(link_quirk, int, S_IRUGO | S_IWUSR);
xhci_set_cmd_ring_deq(xhci);
}
+static void xhci_disable_port_wake_on_bits(struct xhci_hcd *xhci)
+{
+ int port_index;
+ __le32 __iomem **port_array;
+ unsigned long flags;
+ u32 t1, t2;
+
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ /* disble usb3 ports Wake bits*/
+ port_index = xhci->num_usb3_ports;
+ port_array = xhci->usb3_ports;
+ while (port_index--) {
+ t1 = readl(port_array[port_index]);
+ t1 = xhci_port_state_to_neutral(t1);
+ t2 = t1 & ~PORT_WAKE_BITS;
+ if (t1 != t2)
+ writel(t2, port_array[port_index]);
+ }
+
+ /* disble usb2 ports Wake bits*/
+ port_index = xhci->num_usb2_ports;
+ port_array = xhci->usb2_ports;
+ while (port_index--) {
+ t1 = readl(port_array[port_index]);
+ t1 = xhci_port_state_to_neutral(t1);
+ t2 = t1 & ~PORT_WAKE_BITS;
+ if (t1 != t2)
+ writel(t2, port_array[port_index]);
+ }
+
+ spin_unlock_irqrestore(&xhci->lock, flags);
+}
+
/*
* Stop HC (not bus-specific)
*
* This is called when the machine transition into S3/S4 mode.
*
*/
-int xhci_suspend(struct xhci_hcd *xhci)
+int xhci_suspend(struct xhci_hcd *xhci, bool do_wakeup)
{
int rc = 0;
unsigned int delay = XHCI_MAX_HALT_USEC;
xhci->shared_hcd->state != HC_STATE_SUSPENDED)
return -EINVAL;
+ /* Clear root port wake on bits if wakeup not allowed. */
+ if (!do_wakeup)
+ xhci_disable_port_wake_on_bits(xhci);
+
/* Don't poll the roothubs on bus suspend. */
xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
}
}
-/* Deal with stalled endpoints. The core should have sent the control message
- * to clear the halt condition. However, we need to make the xHCI hardware
- * reset its sequence number, since a device will expect a sequence number of
- * zero after the halt condition is cleared.
+/* Called when clearing halted device. The core should have sent the control
+ * message to clear the device halt condition. The host side of the halt should
+ * already be cleared with a reset endpoint command issued when the STALL tx
+ * event was received.
+ *
* Context: in_interrupt
*/
+
void xhci_endpoint_reset(struct usb_hcd *hcd,
struct usb_host_endpoint *ep)
{
struct xhci_hcd *xhci;
- struct usb_device *udev;
- unsigned int ep_index;
- unsigned long flags;
- int ret;
- struct xhci_virt_ep *virt_ep;
- struct xhci_command *command;
xhci = hcd_to_xhci(hcd);
- udev = (struct usb_device *) ep->hcpriv;
- /* Called with a root hub endpoint (or an endpoint that wasn't added
- * with xhci_add_endpoint()
- */
- if (!ep->hcpriv)
- return;
- ep_index = xhci_get_endpoint_index(&ep->desc);
- virt_ep = &xhci->devs[udev->slot_id]->eps[ep_index];
- if (!virt_ep->stopped_td) {
- xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep,
- "Endpoint 0x%x not halted, refusing to reset.",
- ep->desc.bEndpointAddress);
- return;
- }
- if (usb_endpoint_xfer_control(&ep->desc)) {
- xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep,
- "Control endpoint stall already handled.");
- return;
- }
- command = xhci_alloc_command(xhci, false, false, GFP_ATOMIC);
- if (!command)
- return;
-
- xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep,
- "Queueing reset endpoint command");
- spin_lock_irqsave(&xhci->lock, flags);
- ret = xhci_queue_reset_ep(xhci, command, udev->slot_id, ep_index);
/*
- * Can't change the ring dequeue pointer until it's transitioned to the
- * stopped state, which is only upon a successful reset endpoint
- * command. Better hope that last command worked!
+ * We might need to implement the config ep cmd in xhci 4.8.1 note:
+ * The Reset Endpoint Command may only be issued to endpoints in the
+ * Halted state. If software wishes reset the Data Toggle or Sequence
+ * Number of an endpoint that isn't in the Halted state, then software
+ * may issue a Configure Endpoint Command with the Drop and Add bits set
+ * for the target endpoint. that is in the Stopped state.
*/
- if (!ret) {
- xhci_cleanup_stalled_ring(xhci, udev, ep_index);
- kfree(virt_ep->stopped_td);
- xhci_ring_cmd_db(xhci);
- }
- virt_ep->stopped_td = NULL;
- virt_ep->stopped_stream = 0;
- spin_unlock_irqrestore(&xhci->lock, flags);
- if (ret)
- xhci_warn(xhci, "FIXME allocate a new ring segment\n");
+ /* For now just print debug to follow the situation */
+ xhci_dbg(xhci, "Endpoint 0x%x ep reset callback called\n",
+ ep->desc.bEndpointAddress);
}
static int xhci_check_streams_endpoint(struct xhci_hcd *xhci,
projects / cascardo / linux.git / blobdiff