* struct mipi_dsi_msg - read/write DSI buffer
* @channel: virtual channel id
* @type: payload data type
+ * @flags: flags controlling this message transmission
* @tx_len: length of @tx_buf
* @tx_buf: data to be written
* @rx_len: length of @rx_buf
void *rx_buf;
};
+bool mipi_dsi_packet_format_is_short(u8 type);
+bool mipi_dsi_packet_format_is_long(u8 type);
+
+/**
+ * struct mipi_dsi_packet - represents a MIPI DSI packet in protocol format
+ * @size: size (in bytes) of the packet
+ * @header: the four bytes that make up the header (Data ID, Word Count or
+ * Packet Data, and ECC)
+ * @payload_length: number of bytes in the payload
+ * @payload: a pointer to a buffer containing the payload, if any
+ */
+struct mipi_dsi_packet {
+ size_t size;
+ u8 header[4];
+ size_t payload_length;
+ const u8 *payload;
+};
+
+int mipi_dsi_create_packet(struct mipi_dsi_packet *packet,
+ const struct mipi_dsi_msg *msg);
+
/**
* struct mipi_dsi_host_ops - DSI bus operations
* @attach: attach DSI device to DSI host
* @detach: detach DSI device from DSI host
- * @transfer: send and/or receive DSI packet, return number of received bytes,
- * or error
+ * @transfer: transmit a DSI packet
+ *
+ * DSI packets transmitted by .transfer() are passed in as mipi_dsi_msg
+ * structures. This structure contains information about the type of packet
+ * being transmitted as well as the transmit and receive buffers. When an
+ * error is encountered during transmission, this function will return a
+ * negative error code. On success it shall return the number of bytes
+ * transmitted for write packets or the number of bytes received for read
+ * packets.
+ *
+ * Note that typically DSI packet transmission is atomic, so the .transfer()
+ * function will seldomly return anything other than the number of bytes
+ * contained in the transmit buffer on success.
*/
struct mipi_dsi_host_ops {
int (*attach)(struct mipi_dsi_host *host,
int (*detach)(struct mipi_dsi_host *host,
struct mipi_dsi_device *dsi);
ssize_t (*transfer)(struct mipi_dsi_host *host,
- struct mipi_dsi_msg *msg);
+ const struct mipi_dsi_msg *msg);
};
/**
#define MIPI_DSI_MODE_EOT_PACKET BIT(9)
/* device supports non-continuous clock behavior (DSI spec 5.6.1) */
#define MIPI_DSI_CLOCK_NON_CONTINUOUS BIT(10)
+/* transmit data in low power */
+#define MIPI_DSI_MODE_LPM BIT(11)
enum mipi_dsi_pixel_format {
MIPI_DSI_FMT_RGB888,
int mipi_dsi_attach(struct mipi_dsi_device *dsi);
int mipi_dsi_detach(struct mipi_dsi_device *dsi);
-ssize_t mipi_dsi_dcs_write(struct mipi_dsi_device *dsi, const void *data,
- size_t len);
+int mipi_dsi_set_maximum_return_packet_size(struct mipi_dsi_device *dsi,
+ u16 value);
+
+ssize_t mipi_dsi_generic_write(struct mipi_dsi_device *dsi, const void *payload,
+ size_t size);
+ssize_t mipi_dsi_generic_read(struct mipi_dsi_device *dsi, const void *params,
+ size_t num_params, void *data, size_t size);
+
+/**
+ * enum mipi_dsi_dcs_tear_mode - Tearing Effect Output Line mode
+ * @MIPI_DSI_DCS_TEAR_MODE_VBLANK: the TE output line consists of V-Blanking
+ * information only
+ * @MIPI_DSI_DCS_TEAR_MODE_VHBLANK : the TE output line consists of both
+ * V-Blanking and H-Blanking information
+ */
+enum mipi_dsi_dcs_tear_mode {
+ MIPI_DSI_DCS_TEAR_MODE_VBLANK,
+ MIPI_DSI_DCS_TEAR_MODE_VHBLANK,
+};
+
+ssize_t mipi_dsi_dcs_write_buffer(struct mipi_dsi_device *dsi,
+ const void *data, size_t len);
+ssize_t mipi_dsi_dcs_write(struct mipi_dsi_device *dsi, u8 cmd,
+ const void *data, size_t len);
ssize_t mipi_dsi_dcs_read(struct mipi_dsi_device *dsi, u8 cmd, void *data,
size_t len);
+int mipi_dsi_dcs_enter_sleep_mode(struct mipi_dsi_device *dsi);
+int mipi_dsi_dcs_exit_sleep_mode(struct mipi_dsi_device *dsi);
+int mipi_dsi_dcs_set_display_off(struct mipi_dsi_device *dsi);
+int mipi_dsi_dcs_set_display_on(struct mipi_dsi_device *dsi);
+int mipi_dsi_dcs_set_tear_off(struct mipi_dsi_device *dsi);
+int mipi_dsi_dcs_set_tear_on(struct mipi_dsi_device *dsi,
+ enum mipi_dsi_dcs_tear_mode mode);
/**
* struct mipi_dsi_driver - DSI driver