};
};
+/**
+ * ieee80211_sched_scan_ies - scheduled scan IEs
+ *
+ * This structure is used to pass the appropriate IEs to be used in scheduled
+ * scans for all bands. It contains both the IEs passed from the userspace
+ * and the ones generated by mac80211.
+ *
+ * @ie: array with the IEs for each supported band
+ * @len: array with the total length of the IEs for each band
+ */
+struct ieee80211_sched_scan_ies {
+ u8 *ie[IEEE80211_NUM_BANDS];
+ size_t len[IEEE80211_NUM_BANDS];
+};
+
static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb)
{
return (struct ieee80211_tx_info *)skb->cb;
* acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key
* handler.
* The update_tkip_key() call updates the driver with the new phase 1 key.
- * This happens everytime the iv16 wraps around (every 65536 packets). The
+ * This happens every time the iv16 wraps around (every 65536 packets). The
* set_key() call will happen only once for each key (unless the AP did
* rekeying), it will not include a valid phase 1 key. The valid phase 1 key is
* provided by update_tkip_key only. The trigger that makes mac80211 call this
* you should ensure to cancel it on this callback.
* Must be implemented and can sleep.
*
+ * @suspend: Suspend the device; mac80211 itself will quiesce before and
+ * stop transmitting and doing any other configuration, and then
+ * ask the device to suspend. This is only invoked when WoWLAN is
+ * configured, otherwise the device is deconfigured completely and
+ * reconfigured at resume time.
+ *
+ * @resume: If WoWLAN was configured, this indicates that mac80211 is
+ * now resuming its operation, after this the device must be fully
+ * functional again. If this returns an error, the only way out is
+ * to also unregister the device. If it returns 1, then mac80211
+ * will also go through the regular complete restart on resume.
+ *
* @add_interface: Called when a netdevice attached to the hardware is
* enabled. Because it is not called for monitor mode devices, @start
* and @stop must be implemented.
* any error unless this callback returned a negative error code.
* The callback can sleep.
*
+ * @sched_scan_start: Ask the hardware to start scanning repeatedly at
+ * specific intervals. The driver must call the
+ * ieee80211_sched_scan_results() function whenever it finds results.
+ * This process will continue until sched_scan_stop is called.
+ *
+ * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan.
+ *
* @sw_scan_start: Notifier function that is called just before a software scan
* is started. Can be NULL, if the driver doesn't need this notification.
* The callback can sleep.
* that TX/RX_STOP can pass NULL for this parameter.
* The @buf_size parameter is only valid when the action is set to
* %IEEE80211_AMPDU_TX_OPERATIONAL and indicates the peer's reorder
- * buffer size (number of subframes) for this session -- aggregates
- * containing more subframes than this may not be transmitted to the peer.
+ * buffer size (number of subframes) for this session -- the driver
+ * may neither send aggregates containing more subframes than this
+ * nor send aggregates in a way that lost frames would exceed the
+ * buffer size. If just limiting the aggregate size, this would be
+ * possible with a buf_size of 8:
+ * - TX: 1.....7
+ * - RX: 2....7 (lost frame #1)
+ * - TX: 8..1...
+ * which is invalid since #1 was now re-transmitted well past the
+ * buffer size of 8. Correct ways to retransmit #1 would be:
+ * - TX: 1 or 18 or 81
+ * Even "189" would be wrong since 1 could be lost again.
+ *
* Returns a negative error code on failure.
* The callback can sleep.
*
* @set_ringparam: Set tx and rx ring sizes.
*
* @get_ringparam: Get tx and rx ring current and maximum sizes.
+ *
+ * @tx_frames_pending: Check if there is any pending frame in the hardware
+ * queues before entering power save.
+ *
+ * @set_bitrate_mask: Set a mask of rates to be used for rate control selection
+ * when transmitting a frame. Currently only legacy rates are handled.
+ * The callback can sleep.
*/
struct ieee80211_ops {
void (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb);
int (*start)(struct ieee80211_hw *hw);
void (*stop)(struct ieee80211_hw *hw);
+#ifdef CONFIG_PM
+ int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan);
+ int (*resume)(struct ieee80211_hw *hw);
+#endif
int (*add_interface)(struct ieee80211_hw *hw,
struct ieee80211_vif *vif);
int (*change_interface)(struct ieee80211_hw *hw,
u32 iv32, u16 *phase1key);
int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
struct cfg80211_scan_request *req);
+ int (*sched_scan_start)(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct cfg80211_sched_scan_request *req,
+ struct ieee80211_sched_scan_ies *ies);
+ void (*sched_scan_stop)(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif);
void (*sw_scan_start)(struct ieee80211_hw *hw);
void (*sw_scan_complete)(struct ieee80211_hw *hw);
int (*get_stats)(struct ieee80211_hw *hw,
int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx);
void (*get_ringparam)(struct ieee80211_hw *hw,
u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max);
+ bool (*tx_frames_pending)(struct ieee80211_hw *hw);
+ int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+ const struct cfg80211_bitrate_mask *mask);
};
/**
*/
#define IEEE80211_TX_STATUS_HEADROOM 13
+/**
+ * ieee80211_sta_set_tim - set the TIM bit for a sleeping station
+ *
+ * If a driver buffers frames for a powersave station instead of passing
+ * them back to mac80211 for retransmission, the station needs to be told
+ * to wake up using the TIM bitmap in the beacon.
+ *
+ * This function sets the station's TIM bit - it will be cleared when the
+ * station wakes up.
+ */
+void ieee80211_sta_set_tim(struct ieee80211_sta *sta);
+
/**
* ieee80211_tx_status - transmit status callback
*
void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw,
struct sk_buff *skb);
+/**
+ * ieee80211_report_low_ack - report non-responding station
+ *
+ * When operating in AP-mode, call this function to report a non-responding
+ * connected STA.
+ *
+ * @sta: the non-responding connected sta
+ * @num_packets: number of packets sent to @sta without a response
+ */
+void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets);
+
/**
* ieee80211_beacon_get_tim - beacon generation function
* @hw: pointer obtained from ieee80211_alloc_hw().
*/
void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted);
+/**
+ * ieee80211_sched_scan_results - got results from scheduled scan
+ *
+ * When a scheduled scan is running, this function needs to be called by the
+ * driver whenever there are new scan results available.
+ *
+ * @hw: the hardware that is performing scheduled scans
+ */
+void ieee80211_sched_scan_results(struct ieee80211_hw *hw);
+
+/**
+ * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped
+ *
+ * When a scheduled scan is running, this function can be called by
+ * the driver if it needs to stop the scan to perform another task.
+ * Usual scenarios are drivers that cannot continue the scheduled scan
+ * while associating, for instance.
+ *
+ * @hw: the hardware that is performing scheduled scans
+ */
+void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw);
+
/**
* ieee80211_iterate_active_interfaces - iterate active interfaces
*
projects / cascardo / linux.git / blobdiff