* QoS mapping is relevant for IP packets, it is only valid during an
* association. This is cleared on disassociation and AP restart.
*
+ * @NL80211_CMD_ADD_TX_TS: Ask the kernel to add a traffic stream for the given
+ * %NL80211_ATTR_TSID and %NL80211_ATTR_MAC with %NL80211_ATTR_USER_PRIO
+ * and %NL80211_ATTR_ADMITTED_TIME parameters.
+ * Note that the action frame handshake with the AP shall be handled by
+ * userspace via the normal management RX/TX framework, this only sets
+ * up the TX TS in the driver/device.
+ * If the admitted time attribute is not added then the request just checks
+ * if a subsequent setup could be successful, the intent is to use this to
+ * avoid setting up a session with the AP when local restrictions would
+ * make that impossible. However, the subsequent "real" setup may still
+ * fail even if the check was successful.
+ * @NL80211_CMD_DEL_TX_TS: Remove an existing TS with the %NL80211_ATTR_TSID
+ * and %NL80211_ATTR_MAC parameters. It isn't necessary to call this
+ * before removing a station entry entirely, or before disassociating
+ * or similar, cleanup will happen in the driver/device in this case.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
NL80211_CMD_SET_QOS_MAP,
+ NL80211_CMD_ADD_TX_TS,
+ NL80211_CMD_DEL_TX_TS,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
* creation then the new interface will be owned by the netlink socket
* that created it and will be destroyed when the socket is closed
*
+ * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is
+ * the TDLS link initiator.
+ *
+ * @NL80211_ATTR_USE_RRM: flag for indicating whether the current connection
+ * shall support Radio Resource Measurements (11k). This attribute can be
+ * used with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests.
+ * User space applications are expected to use this flag only if the
+ * underlying device supports these minimal RRM features:
+ * %NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES,
+ * %NL80211_FEATURE_QUIET,
+ * If this flag is used, driver must add the Power Capabilities IE to the
+ * association request. In addition, it must also set the RRM capability
+ * flag in the association request's Capability Info field.
+ *
+ * @NL80211_ATTR_WIPHY_DYN_ACK: flag attribute used to enable ACK timeout
+ * estimation algorithm (dynack). In order to activate dynack
+ * %NL80211_FEATURE_ACKTO_ESTIMATION feature flag must be set by lower
+ * drivers to indicate dynack capability. Dynack is automatically disabled
+ * setting valid value for coverage class.
+ *
+ * @NL80211_ATTR_TSID: a TSID value (u8 attribute)
+ * @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute)
+ * @NL80211_ATTR_ADMITTED_TIME: admitted time in units of 32 microseconds
+ * (per second) (u16 attribute)
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
NL80211_ATTR_CSA_C_OFFSETS_TX,
NL80211_ATTR_MAX_CSA_COUNTERS,
+ NL80211_ATTR_TDLS_INITIATOR,
+
+ NL80211_ATTR_USE_RRM,
+
+ NL80211_ATTR_WIPHY_DYN_ACK,
+
+ NL80211_ATTR_TSID,
+ NL80211_ATTR_USER_PRIO,
+ NL80211_ATTR_ADMITTED_TIME,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
* @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
* @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
* @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
+ * (if @NL80211_BSS_PRESP_DATA is present then this is known to be
+ * from a probe response, otherwise it may be from the same beacon
+ * that the NL80211_BSS_BEACON_TSF will be from)
* @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
* @NL80211_BSS_CAPABILITY: capability field (CPU order, u16)
* @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
* raw information elements from the probe response/beacon (bin);
- * if the %NL80211_BSS_BEACON_IES attribute is present, the IEs here are
- * from a Probe Response frame; otherwise they are from a Beacon frame.
+ * if the %NL80211_BSS_BEACON_IES attribute is present and the data is
+ * different then the IEs here are from a Probe Response frame; otherwise
+ * they are from a Beacon frame.
* However, if the driver does not indicate the source of the IEs, these
* IEs may be from either frame subtype.
+ * If present, the @NL80211_BSS_PRESP_DATA attribute indicates that the
+ * data here is known to be from a probe response, without any heuristics.
* @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon
* in mBm (100 * dBm) (s32)
* @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon
* yet been received
* @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
* (u32, enum nl80211_bss_scan_width)
+ * @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
+ * (not present if no beacon frame has been received yet)
+ * @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
+ * @NL80211_BSS_TSF is known to be from a probe response (flag attribute)
* @__NL80211_BSS_AFTER_LAST: internal
* @NL80211_BSS_MAX: highest BSS attribute
*/
NL80211_BSS_SEEN_MS_AGO,
NL80211_BSS_BEACON_IES,
NL80211_BSS_CHAN_WIDTH,
+ NL80211_BSS_BEACON_TSF,
+ NL80211_BSS_PRESP_DATA,
/* keep last */
__NL80211_BSS_AFTER_LAST,
* @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic
* channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
* lifetime of a BSS.
+ * @NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES: This device adds a DS Parameter
+ * Set IE to probe requests.
+ * @NL80211_FEATURE_WFA_TPC_IE_IN_PROBES: This device adds a WFA TPC Report IE
+ * to probe requests.
+ * @NL80211_FEATURE_QUIET: This device, in client mode, supports Quiet Period
+ * requests sent to it by an AP.
+ * @NL80211_FEATURE_TX_POWER_INSERTION: This device is capable of inserting the
+ * current tx power value into the TPC Report IE in the spectrum
+ * management TPC Report action frame, and in the Radio Measurement Link
+ * Measurement Report action frame.
+ * @NL80211_FEATURE_ACKTO_ESTIMATION: This driver supports dynamic ACK timeout
+ * estimation (dynack). %NL80211_ATTR_WIPHY_DYN_ACK flag attribute is used
+ * to enable dynack.
*/
enum nl80211_feature_flags {
NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
NL80211_FEATURE_USERSPACE_MPM = 1 << 16,
NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17,
NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = 1 << 18,
+ NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES = 1 << 19,
+ NL80211_FEATURE_WFA_TPC_IE_IN_PROBES = 1 << 20,
+ NL80211_FEATURE_QUIET = 1 << 21,
+ NL80211_FEATURE_TX_POWER_INSERTION = 1 << 22,
+ NL80211_FEATURE_ACKTO_ESTIMATION = 1 << 23,
};
/**