--- /dev/null
+Device Tree Clock bindings for arch-at91
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be one of the following:
+ "atmel,at91rm9200-pmc" or
+ "atmel,at91sam9g45-pmc" or
+ "atmel,at91sam9n12-pmc" or
+ "atmel,at91sam9x5-pmc" or
+ "atmel,sama5d3-pmc":
+ at91 PMC (Power Management Controller)
+ All at91 specific clocks (clocks defined below) must be child
+ node of the PMC node.
+
+ "atmel,at91rm9200-clk-main":
+ at91 main oscillator
+
+ "atmel,at91rm9200-clk-master" or
+ "atmel,at91sam9x5-clk-master":
+ at91 master clock
+
+ "atmel,at91sam9x5-clk-peripheral" or
+ "atmel,at91rm9200-clk-peripheral":
+ at91 peripheral clocks
+
+ "atmel,at91rm9200-clk-pll" or
+ "atmel,at91sam9g45-clk-pll" or
+ "atmel,at91sam9g20-clk-pllb" or
+ "atmel,sama5d3-clk-pll":
+ at91 pll clocks
+
+ "atmel,at91sam9x5-clk-plldiv":
+ at91 plla divisor
+
+ "atmel,at91rm9200-clk-programmable" or
+ "atmel,at91sam9g45-clk-programmable" or
+ "atmel,at91sam9x5-clk-programmable":
+ at91 programmable clocks
+
+ "atmel,at91sam9x5-clk-smd":
+ at91 SMD (Soft Modem) clock
+
+ "atmel,at91rm9200-clk-system":
+ at91 system clocks
+
+ "atmel,at91rm9200-clk-usb" or
+ "atmel,at91sam9x5-clk-usb" or
+ "atmel,at91sam9n12-clk-usb":
+ at91 usb clock
+
+ "atmel,at91sam9x5-clk-utmi":
+ at91 utmi clock
+
+Required properties for PMC node:
+- reg : defines the IO memory reserved for the PMC.
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- interrupts : shall be set to PMC interrupt line.
+- interrupt-controller : tell that the PMC is an interrupt controller.
+- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
+ and reflect the bit position in the PMC_ER/DR/SR registers.
+ You can use the dt macros defined in dt-bindings/clk/at91.h.
+ 0 (AT91_PMC_MOSCS) -> main oscillator ready
+ 1 (AT91_PMC_LOCKA) -> PLL A ready
+ 2 (AT91_PMC_LOCKB) -> PLL B ready
+ 3 (AT91_PMC_MCKRDY) -> master clock ready
+ 6 (AT91_PMC_LOCKU) -> UTMI PLL clock ready
+ 8 .. 15 (AT91_PMC_PCKRDY(id)) -> programmable clock ready
+ 16 (AT91_PMC_MOSCSELS) -> main oscillator selected
+ 17 (AT91_PMC_MOSCRCS) -> RC main oscillator stabilized
+ 18 (AT91_PMC_CFDEV) -> clock failure detected
+
+For example:
+ pmc: pmc@fffffc00 {
+ compatible = "atmel,sama5d3-pmc";
+ interrupts = <1 4 7>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #size-cells = <0>;
+ #address-cells = <1>;
+
+ /* put at91 clocks here */
+ };
+
+Required properties for main clock:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<0>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks (optional if clock-frequency is provided) : shall be the slow clock
+ phandle. This clock is used to calculate the main clock rate if
+ "clock-frequency" is not provided.
+- clock-frequency : the main oscillator frequency.Prefer the use of
+ "clock-frequency" over automatic clock rate calculation.
+
+For example:
+ main: mainck {
+ compatible = "atmel,at91rm9200-clk-main";
+ interrupt-parent = <&pmc>;
+ interrupts = <0>;
+ #clock-cells = <0>;
+ clocks = <&ck32k>;
+ clock-frequency = <18432000>;
+ };
+
+Required properties for master clock:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<3>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the master clock sources (see atmel datasheet) phandles.
+ e.g. "<&ck32k>, <&main>, <&plla>, <&pllb>".
+- atmel,clk-output-range : minimum and maximum clock frequency (two u32
+ fields).
+ e.g. output = <0 133000000>; <=> 0 to 133MHz.
+- atmel,clk-divisors : master clock divisors table (four u32 fields).
+ 0 <=> reserved value.
+ e.g. divisors = <1 2 4 6>;
+- atmel,master-clk-have-div3-pres : some SoC use the reserved value 7 in the
+ PRES field as CLOCK_DIV3 (e.g sam9x5).
+
+For example:
+ mck: mck {
+ compatible = "atmel,at91rm9200-clk-master";
+ interrupt-parent = <&pmc>;
+ interrupts = <3>;
+ #clock-cells = <0>;
+ atmel,clk-output-range = <0 133000000>;
+ atmel,clk-divisors = <1 2 4 0>;
+ };
+
+Required properties for peripheral clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- clocks : shall be the master clock phandle.
+ e.g. clocks = <&mck>;
+- name: device tree node describing a specific system clock.
+ * #clock-cells : from common clock binding; shall be set to 0.
+ * reg: peripheral id. See Atmel's datasheets to get a full
+ list of peripheral ids.
+ * atmel,clk-output-range : minimum and maximum clock frequency
+ (two u32 fields). Only valid on at91sam9x5-clk-peripheral
+ compatible IPs.
+
+For example:
+ periph: periphck {
+ compatible = "atmel,at91sam9x5-clk-peripheral";
+ #size-cells = <0>;
+ #address-cells = <1>;
+ clocks = <&mck>;
+
+ ssc0_clk {
+ #clock-cells = <0>;
+ reg = <2>;
+ atmel,clk-output-range = <0 133000000>;
+ };
+
+ usart0_clk {
+ #clock-cells = <0>;
+ reg = <3>;
+ atmel,clk-output-range = <0 66000000>;
+ };
+ };
+
+
+Required properties for pll clocks:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<1>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the main clock phandle.
+- reg : pll id.
+ 0 -> PLL A
+ 1 -> PLL B
+- atmel,clk-input-range : minimum and maximum source clock frequency (two u32
+ fields).
+ e.g. input = <1 32000000>; <=> 1 to 32MHz.
+- #atmel,pll-clk-output-range-cells : number of cells reserved for pll output
+ range description. Sould be set to 2, 3
+ or 4.
+ * 1st and 2nd cells represent the frequency range (min-max).
+ * 3rd cell is optional and represents the OUT field value for the given
+ range.
+ * 4th cell is optional and represents the ICPLL field (PLLICPR
+ register)
+- atmel,pll-clk-output-ranges : pll output frequency ranges + optional parameter
+ depending on #atmel,pll-output-range-cells
+ property value.
+
+For example:
+ plla: pllack {
+ compatible = "atmel,at91sam9g45-clk-pll";
+ interrupt-parent = <&pmc>;
+ interrupts = <1>;
+ #clock-cells = <0>;
+ clocks = <&main>;
+ reg = <0>;
+ atmel,clk-input-range = <2000000 32000000>;
+ #atmel,pll-clk-output-range-cells = <4>;
+ atmel,pll-clk-output-ranges = <74500000 800000000 0 0
+ 69500000 750000000 1 0
+ 64500000 700000000 2 0
+ 59500000 650000000 3 0
+ 54500000 600000000 0 1
+ 49500000 550000000 1 1
+ 44500000 500000000 2 1
+ 40000000 450000000 3 1>;
+ };
+
+Required properties for plldiv clocks (plldiv = pll / 2):
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the plla clock phandle.
+
+The pll divisor is equal to 2 and cannot be changed.
+
+For example:
+ plladiv: plladivck {
+ compatible = "atmel,at91sam9x5-clk-plldiv";
+ #clock-cells = <0>;
+ clocks = <&plla>;
+ };
+
+Required properties for programmable clocks:
+- interrupt-parent : must reference the PMC node.
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- clocks : shall be the programmable clock source phandles.
+ e.g. clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
+- name: device tree node describing a specific prog clock.
+ * #clock-cells : from common clock binding; shall be set to 0.
+ * reg : programmable clock id (register offset from PCKx
+ register).
+ * interrupts : shall be set to "<(8 + id)>".
+
+For example:
+ prog: progck {
+ compatible = "atmel,at91sam9g45-clk-programmable";
+ #size-cells = <0>;
+ #address-cells = <1>;
+ interrupt-parent = <&pmc>;
+ clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
+
+ prog0 {
+ #clock-cells = <0>;
+ reg = <0>;
+ interrupts = <8>;
+ };
+
+ prog1 {
+ #clock-cells = <0>;
+ reg = <1>;
+ interrupts = <9>;
+ };
+ };
+
+
+Required properties for smd clock:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the smd clock source phandles.
+ e.g. clocks = <&plladiv>, <&utmi>;
+
+For example:
+ smd: smdck {
+ compatible = "atmel,at91sam9x5-clk-smd";
+ #clock-cells = <0>;
+ clocks = <&plladiv>, <&utmi>;
+ };
+
+Required properties for system clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- name: device tree node describing a specific system clock.
+ * #clock-cells : from common clock binding; shall be set to 0.
+ * reg: system clock id (bit position in SCER/SCDR/SCSR registers).
+ See Atmel's datasheet to get a full list of system clock ids.
+
+For example:
+ system: systemck {
+ compatible = "atmel,at91rm9200-clk-system";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ddrck {
+ #clock-cells = <0>;
+ reg = <2>;
+ clocks = <&mck>;
+ };
+
+ uhpck {
+ #clock-cells = <0>;
+ reg = <6>;
+ clocks = <&usb>;
+ };
+
+ udpck {
+ #clock-cells = <0>;
+ reg = <7>;
+ clocks = <&usb>;
+ };
+ };
+
+
+Required properties for usb clock:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the smd clock source phandles.
+ e.g. clocks = <&pllb>;
+- atmel,clk-divisors (only available for "atmel,at91rm9200-clk-usb"):
+ usb clock divisor table.
+ e.g. divisors = <1 2 4 0>;
+
+For example:
+ usb: usbck {
+ compatible = "atmel,at91sam9x5-clk-usb";
+ #clock-cells = <0>;
+ clocks = <&plladiv>, <&utmi>;
+ };
+
+ usb: usbck {
+ compatible = "atmel,at91rm9200-clk-usb";
+ #clock-cells = <0>;
+ clocks = <&pllb>;
+ atmel,clk-divisors = <1 2 4 0>;
+ };
+
+
+Required properties for utmi clock:
+- interrupt-parent : must reference the PMC node.
+- interrupts : shall be set to "<AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the main clock source phandle.
+
+For example:
+ utmi: utmick {
+ compatible = "atmel,at91sam9x5-clk-utmi";
+ interrupt-parent = <&pmc>;
+ interrupts = <AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>;
+ #clock-cells = <0>;
+ clocks = <&main>;
+ };
projects / cascardo / linux.git / commitdiff