* 'next/deletion' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: mach-loki: delete
ARM: mach-s3c2400: delete
ARM: mach-s3c24a0: delete
The Samsung S3C24XX range of ARM9 System-on-Chip CPUs are supported
by the 's3c2410' architecture of ARM Linux. Currently the S3C2410,
- S3C2412, S3C2413, S3C2416 S3C2440, S3C2442, S3C2443 and S3C2450 devices
+ S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443 and S3C2450 devices
are supported.
- Support for the S3C2400 and S3C24A0 series are in progress.
+ Support for the S3C2400 and S3C24A0 series was never completed and the
+ corresponding code has been removed after a while. If someone wishes to
+ revive this effort, partial support can be retrieved from earlier Linux
+ versions.
The S3C2416 and S3C2450 devices are very similar and S3C2450 support is
included under the arch/arm/mach-s3c2416 directory. Note, whilst core
Support for the following Marvell Kirkwood series SoCs:
88F6180, 88F6192 and 88F6281.
-config ARCH_LOKI
- bool "Marvell Loki (88RC8480)"
- select CPU_FEROCEON
- select GENERIC_CLOCKEVENTS
- select PLAT_ORION
- help
- Support for the Marvell Loki (88RC8480) SoC.
-
config ARCH_LPC32XX
bool "NXP LPC32XX"
select CLKSRC_MMIO
source "arch/arm/mach-ks8695/Kconfig"
-source "arch/arm/mach-loki/Kconfig"
-
source "arch/arm/mach-lpc32xx/Kconfig"
source "arch/arm/mach-msm/Kconfig"
source "arch/arm/plat-tcc/Kconfig"
if ARCH_S3C2410
-source "arch/arm/mach-s3c2400/Kconfig"
source "arch/arm/mach-s3c2410/Kconfig"
source "arch/arm/mach-s3c2412/Kconfig"
source "arch/arm/mach-s3c2416/Kconfig"
machine-$(CONFIG_ARCH_IXP4XX) := ixp4xx
machine-$(CONFIG_ARCH_KIRKWOOD) := kirkwood
machine-$(CONFIG_ARCH_KS8695) := ks8695
-machine-$(CONFIG_ARCH_LOKI) := loki
machine-$(CONFIG_ARCH_LPC32XX) := lpc32xx
machine-$(CONFIG_ARCH_MMP) := mmp
machine-$(CONFIG_ARCH_MSM) := msm
machine-$(CONFIG_ARCH_PXA) := pxa
machine-$(CONFIG_ARCH_REALVIEW) := realview
machine-$(CONFIG_ARCH_RPC) := rpc
-machine-$(CONFIG_ARCH_S3C2410) := s3c2410 s3c2400 s3c2412 s3c2416 s3c2440 s3c2443
-machine-$(CONFIG_ARCH_S3C24A0) := s3c24a0
+machine-$(CONFIG_ARCH_S3C2410) := s3c2410 s3c2412 s3c2416 s3c2440 s3c2443
machine-$(CONFIG_ARCH_S3C64XX) := s3c64xx
machine-$(CONFIG_ARCH_S5P64X0) := s5p64x0
machine-$(CONFIG_ARCH_S5PC100) := s5pc100
+++ /dev/null
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_EXPERT=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_LOKI=y
-CONFIG_MACH_LB88RC8480=y
-# CONFIG_CPU_FEROCEON_OLD_ID is not set
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IPV6 is not set
-CONFIG_NET_PKTGEN=m
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_MTD=y
-CONFIG_MTD_PARTITIONS=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_CHAR=y
-CONFIG_MTD_BLOCK=y
-CONFIG_FTL=y
-CONFIG_NFTL=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_GEOMETRY=y
-CONFIG_MTD_CFI_I4=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_CFI_STAA=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_M25P80=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_VERIFY_WRITE=y
-CONFIG_MTD_NAND_ORION=y
-CONFIG_BLK_DEV_LOOP=y
-# CONFIG_MISC_DEVICES is not set
-# CONFIG_SCSI_PROC_FS is not set
-CONFIG_BLK_DEV_SD=y
-CONFIG_BLK_DEV_SR=m
-CONFIG_CHR_DEV_SG=m
-CONFIG_ATA=y
-CONFIG_SATA_MV=y
-CONFIG_NETDEVICES=y
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
-CONFIG_MV643XX_ETH=y
-# CONFIG_NETDEV_10000 is not set
-# CONFIG_INPUT_KEYBOARD is not set
-# CONFIG_INPUT_MOUSE is not set
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_RUNTIME_UARTS=2
-CONFIG_LEGACY_PTY_COUNT=16
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_MV64XXX=y
-CONFIG_SPI=y
-# CONFIG_HWMON is not set
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_USB=y
-CONFIG_USB_DEVICEFS=y
-CONFIG_USB_PRINTER=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_STORAGE_DATAFAB=y
-CONFIG_USB_STORAGE_FREECOM=y
-CONFIG_USB_STORAGE_SDDR09=y
-CONFIG_USB_STORAGE_SDDR55=y
-CONFIG_USB_STORAGE_JUMPSHOT=y
-CONFIG_NEW_LEDS=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=y
-# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_XFS_FS=y
-CONFIG_INOTIFY=y
-CONFIG_ISO9660_FS=y
-CONFIG_UDF_FS=m
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_CRAMFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_BSD_DISKLABEL=y
-CONFIG_MINIX_SUBPARTITION=y
-CONFIG_SOLARIS_X86_PARTITION=y
-CONFIG_UNIXWARE_DISKLABEL=y
-CONFIG_LDM_PARTITION=y
-CONFIG_LDM_DEBUG=y
-CONFIG_SUN_PARTITION=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_CODEPAGE_850=y
-CONFIG_NLS_ISO8859_1=y
-CONFIG_NLS_ISO8859_2=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_SYSCTL_SYSCALL_CHECK=y
-CONFIG_DEBUG_USER=y
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_PCBC=m
-CONFIG_CRC_CCITT=y
-CONFIG_CRC16=y
-CONFIG_LIBCRC32C=y
+++ /dev/null
-if ARCH_LOKI
-
-menu "Marvell Loki (88RC8480) Implementations"
-
-config MACH_LB88RC8480
- bool "Marvell LB88RC8480 Development Board"
- help
- Say 'Y' here if you want your kernel to support the
- Marvell LB88RC8480 Development Board.
-
-endmenu
-
-endif
+++ /dev/null
-obj-y += common.o addr-map.o irq.o
-
-obj-$(CONFIG_MACH_LB88RC8480) += lb88rc8480-setup.o
+++ /dev/null
- zreladdr-y := 0x00008000
-params_phys-y := 0x00000100
-initrd_phys-y := 0x00800000
+++ /dev/null
-/*
- * arch/arm/mach-loki/addr-map.c
- *
- * Address map functions for Marvell Loki (88RC8480) SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/mbus.h>
-#include <linux/io.h>
-#include <mach/hardware.h>
-#include "common.h"
-
-/*
- * Generic Address Decode Windows bit settings
- */
-#define TARGET_DDR 0
-#define TARGET_DEV_BUS 1
-#define TARGET_PCIE0 3
-#define TARGET_PCIE1 4
-#define ATTR_DEV_BOOT 0x0f
-#define ATTR_DEV_CS2 0x1b
-#define ATTR_DEV_CS1 0x1d
-#define ATTR_DEV_CS0 0x1e
-#define ATTR_PCIE_IO 0x51
-#define ATTR_PCIE_MEM 0x59
-
-/*
- * Helpers to get DDR bank info
- */
-#define DDR_SIZE_CS(n) DDR_REG(0x1500 + ((n) << 3))
-#define DDR_BASE_CS(n) DDR_REG(0x1504 + ((n) << 3))
-
-/*
- * CPU Address Decode Windows registers
- */
-#define BRIDGE_REG(x) (BRIDGE_VIRT_BASE | (x))
-#define CPU_WIN_CTRL(n) BRIDGE_REG(0x000 | ((n) << 4))
-#define CPU_WIN_BASE(n) BRIDGE_REG(0x004 | ((n) << 4))
-#define CPU_WIN_REMAP_LO(n) BRIDGE_REG(0x008 | ((n) << 4))
-#define CPU_WIN_REMAP_HI(n) BRIDGE_REG(0x00c | ((n) << 4))
-
-
-struct mbus_dram_target_info loki_mbus_dram_info;
-
-static void __init setup_cpu_win(int win, u32 base, u32 size,
- u8 target, u8 attr, int remap)
-{
- u32 ctrl;
-
- base &= 0xffff0000;
- ctrl = ((size - 1) & 0xffff0000) | (attr << 8) | (1 << 5) | target;
-
- writel(base, CPU_WIN_BASE(win));
- writel(ctrl, CPU_WIN_CTRL(win));
- if (win < 2) {
- if (remap < 0)
- remap = base;
-
- writel(remap & 0xffff0000, CPU_WIN_REMAP_LO(win));
- writel(0, CPU_WIN_REMAP_HI(win));
- }
-}
-
-void __init loki_setup_cpu_mbus(void)
-{
- int i;
- int cs;
-
- /*
- * First, disable and clear windows.
- */
- for (i = 0; i < 8; i++) {
- writel(0, CPU_WIN_BASE(i));
- writel(0, CPU_WIN_CTRL(i));
- if (i < 2) {
- writel(0, CPU_WIN_REMAP_LO(i));
- writel(0, CPU_WIN_REMAP_HI(i));
- }
- }
-
- /*
- * Setup windows for PCIe IO+MEM space.
- */
- setup_cpu_win(2, LOKI_PCIE0_MEM_PHYS_BASE, LOKI_PCIE0_MEM_SIZE,
- TARGET_PCIE0, ATTR_PCIE_MEM, -1);
- setup_cpu_win(3, LOKI_PCIE1_MEM_PHYS_BASE, LOKI_PCIE1_MEM_SIZE,
- TARGET_PCIE1, ATTR_PCIE_MEM, -1);
-
- /*
- * Setup MBUS dram target info.
- */
- loki_mbus_dram_info.mbus_dram_target_id = TARGET_DDR;
-
- for (i = 0, cs = 0; i < 4; i++) {
- u32 base = readl(DDR_BASE_CS(i));
- u32 size = readl(DDR_SIZE_CS(i));
-
- /*
- * Chip select enabled?
- */
- if (size & 1) {
- struct mbus_dram_window *w;
-
- w = &loki_mbus_dram_info.cs[cs++];
- w->cs_index = i;
- w->mbus_attr = 0xf & ~(1 << i);
- w->base = base & 0xffff0000;
- w->size = (size | 0x0000ffff) + 1;
- }
- }
- loki_mbus_dram_info.num_cs = cs;
-}
-
-void __init loki_setup_dev_boot_win(u32 base, u32 size)
-{
- setup_cpu_win(4, base, size, TARGET_DEV_BUS, ATTR_DEV_BOOT, -1);
-}
+++ /dev/null
-/*
- * arch/arm/mach-loki/common.c
- *
- * Core functions for Marvell Loki (88RC8480) SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-#include <linux/mbus.h>
-#include <linux/dma-mapping.h>
-#include <asm/page.h>
-#include <asm/timex.h>
-#include <asm/mach/map.h>
-#include <asm/mach/time.h>
-#include <mach/bridge-regs.h>
-#include <mach/loki.h>
-#include <plat/orion_nand.h>
-#include <plat/time.h>
-#include <plat/common.h>
-#include "common.h"
-
-/*****************************************************************************
- * I/O Address Mapping
- ****************************************************************************/
-static struct map_desc loki_io_desc[] __initdata = {
- {
- .virtual = LOKI_REGS_VIRT_BASE,
- .pfn = __phys_to_pfn(LOKI_REGS_PHYS_BASE),
- .length = LOKI_REGS_SIZE,
- .type = MT_DEVICE,
- },
-};
-
-void __init loki_map_io(void)
-{
- iotable_init(loki_io_desc, ARRAY_SIZE(loki_io_desc));
-}
-
-
-/*****************************************************************************
- * GE00
- ****************************************************************************/
-void __init loki_ge0_init(struct mv643xx_eth_platform_data *eth_data)
-{
- writel(0x00079220, GE0_VIRT_BASE + 0x20b0);
-
- orion_ge00_init(eth_data, &loki_mbus_dram_info,
- GE0_PHYS_BASE, IRQ_LOKI_GBE_A_INT,
- 0, LOKI_TCLK);
-}
-
-
-/*****************************************************************************
- * GE01
- ****************************************************************************/
-void __init loki_ge1_init(struct mv643xx_eth_platform_data *eth_data)
-{
- writel(0x00079220, GE1_VIRT_BASE + 0x20b0);
-
- orion_ge01_init(eth_data, &loki_mbus_dram_info,
- GE1_PHYS_BASE, IRQ_LOKI_GBE_B_INT,
- 0, LOKI_TCLK);
-}
-
-
-/*****************************************************************************
- * SAS/SATA
- ****************************************************************************/
-static struct resource loki_sas_resources[] = {
- {
- .name = "mvsas0 mem",
- .start = SAS0_PHYS_BASE,
- .end = SAS0_PHYS_BASE + 0x01ff,
- .flags = IORESOURCE_MEM,
- }, {
- .name = "mvsas0 irq",
- .start = IRQ_LOKI_SAS_A,
- .end = IRQ_LOKI_SAS_A,
- .flags = IORESOURCE_IRQ,
- }, {
- .name = "mvsas1 mem",
- .start = SAS1_PHYS_BASE,
- .end = SAS1_PHYS_BASE + 0x01ff,
- .flags = IORESOURCE_MEM,
- }, {
- .name = "mvsas1 irq",
- .start = IRQ_LOKI_SAS_B,
- .end = IRQ_LOKI_SAS_B,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device loki_sas = {
- .name = "mvsas",
- .id = 0,
- .dev = {
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .num_resources = ARRAY_SIZE(loki_sas_resources),
- .resource = loki_sas_resources,
-};
-
-void __init loki_sas_init(void)
-{
- writel(0x8300f707, DDR_REG(0x1424));
- platform_device_register(&loki_sas);
-}
-
-
-/*****************************************************************************
- * UART0
- ****************************************************************************/
-void __init loki_uart0_init(void)
-{
- orion_uart0_init(UART0_VIRT_BASE, UART0_PHYS_BASE,
- IRQ_LOKI_UART0, LOKI_TCLK);
-}
-
-/*****************************************************************************
- * UART1
- ****************************************************************************/
-void __init loki_uart1_init(void)
-{
- orion_uart1_init(UART1_VIRT_BASE, UART1_PHYS_BASE,
- IRQ_LOKI_UART1, LOKI_TCLK);
-}
-
-
-/*****************************************************************************
- * Time handling
- ****************************************************************************/
-void __init loki_init_early(void)
-{
- orion_time_set_base(TIMER_VIRT_BASE);
-}
-
-static void loki_timer_init(void)
-{
- orion_time_init(BRIDGE_VIRT_BASE, BRIDGE_INT_TIMER1_CLR,
- IRQ_LOKI_BRIDGE, LOKI_TCLK);
-}
-
-struct sys_timer loki_timer = {
- .init = loki_timer_init,
-};
-
-
-/*****************************************************************************
- * General
- ****************************************************************************/
-void __init loki_init(void)
-{
- printk(KERN_INFO "Loki ID: 88RC8480. TCLK=%d.\n", LOKI_TCLK);
-
- loki_setup_cpu_mbus();
-}
+++ /dev/null
-/*
- * arch/arm/mach-loki/common.h
- *
- * Core functions for Marvell Loki (88RC8480) SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ARCH_LOKI_COMMON_H
-#define __ARCH_LOKI_COMMON_H
-
-struct mv643xx_eth_platform_data;
-
-/*
- * Basic Loki init functions used early by machine-setup.
- */
-void loki_map_io(void);
-void loki_init(void);
-void loki_init_early(void);
-void loki_init_irq(void);
-
-extern struct mbus_dram_target_info loki_mbus_dram_info;
-void loki_setup_cpu_mbus(void);
-void loki_setup_dev_boot_win(u32 base, u32 size);
-
-void loki_ge0_init(struct mv643xx_eth_platform_data *eth_data);
-void loki_ge1_init(struct mv643xx_eth_platform_data *eth_data);
-void loki_sas_init(void);
-void loki_uart0_init(void);
-void loki_uart1_init(void);
-
-extern struct sys_timer loki_timer;
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/bridge-regs.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_BRIDGE_REGS_H
-#define __ASM_ARCH_BRIDGE_REGS_H
-
-#include <mach/loki.h>
-
-#define RSTOUTn_MASK (BRIDGE_VIRT_BASE | 0x0108)
-#define SOFT_RESET_OUT_EN 0x00000004
-
-#define SYSTEM_SOFT_RESET (BRIDGE_VIRT_BASE | 0x010c)
-#define SOFT_RESET 0x00000001
-
-#define BRIDGE_INT_TIMER1_CLR 0x0004
-
-#define IRQ_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0200)
-#define IRQ_CAUSE_OFF 0x0000
-#define IRQ_MASK_OFF 0x0004
-
-#define TIMER_VIRT_BASE (BRIDGE_VIRT_BASE | 0x0300)
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/debug-macro.S
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <mach/loki.h>
-
- .macro addruart, rp, rv
- ldr \rp, =LOKI_REGS_PHYS_BASE
- ldr \rv, =LOKI_REGS_VIRT_BASE
- orr \rp, \rp, #0x00012000
- orr \rv, \rv, #0x00012000
- .endm
-
-#define UART_SHIFT 2
-#include <asm/hardware/debug-8250.S>
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for Marvell Loki (88RC8480) platforms
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <mach/bridge-regs.h>
-
- .macro disable_fiq
- .endm
-
- .macro arch_ret_to_user, tmp1, tmp2
- .endm
-
- .macro get_irqnr_preamble, base, tmp
- ldr \base, =IRQ_VIRT_BASE
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \irqstat, [\base, #IRQ_CAUSE_OFF]
- ldr \tmp, [\base, #IRQ_MASK_OFF]
- mov \irqnr, #0
- ands \irqstat, \irqstat, \tmp
- clzne \irqnr, \irqstat
- rsbne \irqnr, \irqnr, #31
- .endm
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/hardware.h
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#include "loki.h"
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/io.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_IO_H
-#define __ASM_ARCH_IO_H
-
-#include "loki.h"
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-static inline void __iomem *__io(unsigned long addr)
-{
- return (void __iomem *)((addr - LOKI_PCIE0_IO_PHYS_BASE)
- + LOKI_PCIE0_IO_VIRT_BASE);
-}
-
-#define __io(a) __io(a)
-#define __mem_pci(a) (a)
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/irqs.h
- *
- * IRQ definitions for Marvell Loki (88RC8480) SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H
-
-#include "loki.h" /* need GPIO_MAX */
-
-/*
- * Interrupt Controller
- */
-#define IRQ_LOKI_PCIE_A_CPU_DRBL 0
-#define IRQ_LOKI_CPU_PCIE_A_DRBL 1
-#define IRQ_LOKI_PCIE_B_CPU_DRBL 2
-#define IRQ_LOKI_CPU_PCIE_B_DRBL 3
-#define IRQ_LOKI_COM_A_ERR 6
-#define IRQ_LOKI_COM_A_IN 7
-#define IRQ_LOKI_COM_A_OUT 8
-#define IRQ_LOKI_COM_B_ERR 9
-#define IRQ_LOKI_COM_B_IN 10
-#define IRQ_LOKI_COM_B_OUT 11
-#define IRQ_LOKI_DMA_A 12
-#define IRQ_LOKI_DMA_B 13
-#define IRQ_LOKI_SAS_A 14
-#define IRQ_LOKI_SAS_B 15
-#define IRQ_LOKI_DDR 16
-#define IRQ_LOKI_XOR 17
-#define IRQ_LOKI_BRIDGE 18
-#define IRQ_LOKI_PCIE_A_ERR 20
-#define IRQ_LOKI_PCIE_A_INT 21
-#define IRQ_LOKI_PCIE_B_ERR 22
-#define IRQ_LOKI_PCIE_B_INT 23
-#define IRQ_LOKI_GBE_A_INT 24
-#define IRQ_LOKI_GBE_B_INT 25
-#define IRQ_LOKI_DEV_ERR 26
-#define IRQ_LOKI_UART0 27
-#define IRQ_LOKI_UART1 28
-#define IRQ_LOKI_TWSI 29
-#define IRQ_LOKI_GPIO_23_0 30
-#define IRQ_LOKI_GPIO_25_24 31
-
-/*
- * Loki General Purpose Pins
- */
-#define IRQ_LOKI_GPIO_START 32
-#define NR_GPIO_IRQS GPIO_MAX
-
-#define NR_IRQS (IRQ_LOKI_GPIO_START + NR_GPIO_IRQS)
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/loki.h
- *
- * Generic definitions for Marvell Loki (88RC8480) SoC flavors
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_LOKI_H
-#define __ASM_ARCH_LOKI_H
-
-/*
- * Marvell Loki (88RC8480) address maps.
- *
- * phys
- * d0000000 on-chip peripheral registers
- * e0000000 PCIe 0 Memory space
- * e8000000 PCIe 1 Memory space
- * f0000000 PCIe 0 I/O space
- * f0100000 PCIe 1 I/O space
- *
- * virt phys size
- * fed00000 d0000000 1M on-chip peripheral registers
- * fee00000 f0000000 64K PCIe 0 I/O space
- * fef00000 f0100000 64K PCIe 1 I/O space
- */
-
-#define LOKI_REGS_PHYS_BASE 0xd0000000
-#define LOKI_REGS_VIRT_BASE 0xfed00000
-#define LOKI_REGS_SIZE SZ_1M
-
-#define LOKI_PCIE0_IO_PHYS_BASE 0xf0000000
-#define LOKI_PCIE0_IO_VIRT_BASE 0xfee00000
-#define LOKI_PCIE0_IO_BUS_BASE 0x00000000
-#define LOKI_PCIE0_IO_SIZE SZ_64K
-
-#define LOKI_PCIE1_IO_PHYS_BASE 0xf0100000
-#define LOKI_PCIE1_IO_VIRT_BASE 0xfef00000
-#define LOKI_PCIE1_IO_BUS_BASE 0x00000000
-#define LOKI_PCIE1_IO_SIZE SZ_64K
-
-#define LOKI_PCIE0_MEM_PHYS_BASE 0xe0000000
-#define LOKI_PCIE0_MEM_SIZE SZ_128M
-
-#define LOKI_PCIE1_MEM_PHYS_BASE 0xe8000000
-#define LOKI_PCIE1_MEM_SIZE SZ_128M
-
-/*
- * Register Map
- */
-#define DEV_BUS_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x10000)
-#define DEV_BUS_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x10000)
-#define UART0_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2000)
-#define UART0_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2000)
-#define UART1_PHYS_BASE (DEV_BUS_PHYS_BASE | 0x2100)
-#define UART1_VIRT_BASE (DEV_BUS_VIRT_BASE | 0x2100)
-
-#define BRIDGE_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x20000)
-
-#define PCIE0_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x30000)
-
-#define PCIE1_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0x40000)
-
-#define SAS0_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x80000)
-
-#define SAS1_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0x90000)
-
-#define GE0_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0xa0000)
-#define GE0_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xa0000)
-
-#define GE1_PHYS_BASE (LOKI_REGS_PHYS_BASE | 0xb0000)
-#define GE1_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xb0000)
-
-#define DDR_VIRT_BASE (LOKI_REGS_VIRT_BASE | 0xf0000)
-#define DDR_REG(x) (DDR_VIRT_BASE | (x))
-
-
-#define GPIO_MAX 8
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/memory.h
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-#define PLAT_PHYS_OFFSET UL(0x00000000)
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/system.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-#include <mach/bridge-regs.h>
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-static inline void arch_reset(char mode, const char *cmd)
-{
- /*
- * Enable soft reset to assert RSTOUTn.
- */
- writel(SOFT_RESET_OUT_EN, RSTOUTn_MASK);
-
- /*
- * Assert soft reset.
- */
- writel(SOFT_RESET, SYSTEM_SOFT_RESET);
-
- while (1)
- ;
-}
-
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/timex.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#define CLOCK_TICK_RATE (100 * HZ)
-
-#define LOKI_TCLK 180000000
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/uncompress.h
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/serial_reg.h>
-#include <mach/loki.h>
-
-#define SERIAL_BASE ((unsigned char *)UART0_PHYS_BASE)
-
-static void putc(const char c)
-{
- unsigned char *base = SERIAL_BASE;
- int i;
-
- for (i = 0; i < 0x1000; i++) {
- if (base[UART_LSR << 2] & UART_LSR_THRE)
- break;
- barrier();
- }
-
- base[UART_TX << 2] = c;
-}
-
-static void flush(void)
-{
- unsigned char *base = SERIAL_BASE;
- unsigned char mask;
- int i;
-
- mask = UART_LSR_TEMT | UART_LSR_THRE;
-
- for (i = 0; i < 0x1000; i++) {
- if ((base[UART_LSR << 2] & mask) == mask)
- break;
- barrier();
- }
-}
-
-/*
- * nothing to do
- */
-#define arch_decomp_setup()
-#define arch_decomp_wdog()
+++ /dev/null
-/*
- * arch/arm/mach-loki/include/mach/vmalloc.h
- */
-
-#define VMALLOC_END 0xfe800000UL
+++ /dev/null
-/*
- * arch/arm/mach-loki/irq.c
- *
- * Marvell Loki (88RC8480) IRQ handling.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-#include <mach/bridge-regs.h>
-#include <plat/irq.h>
-#include "common.h"
-
-void __init loki_init_irq(void)
-{
- orion_irq_init(0, (void __iomem *)(IRQ_VIRT_BASE + IRQ_MASK_OFF));
-}
+++ /dev/null
-/*
- * arch/arm/mach-loki/lb88rc8480-setup.c
- *
- * Marvell LB88RC8480 Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mtd/nand.h>
-#include <linux/timer.h>
-#include <linux/ata_platform.h>
-#include <linux/mv643xx_eth.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <mach/loki.h>
-#include "common.h"
-
-#define LB88RC8480_FLASH_BOOT_CS_BASE 0xf8000000
-#define LB88RC8480_FLASH_BOOT_CS_SIZE SZ_128M
-
-#define LB88RC8480_NOR_BOOT_BASE 0xff000000
-#define LB88RC8480_NOR_BOOT_SIZE SZ_16M
-
-static struct mtd_partition lb88rc8480_boot_flash_parts[] = {
- {
- .name = "kernel",
- .offset = 0,
- .size = SZ_2M,
- }, {
- .name = "root-fs",
- .offset = SZ_2M,
- .size = (SZ_8M + SZ_4M + SZ_1M),
- }, {
- .name = "u-boot",
- .offset = (SZ_8M + SZ_4M + SZ_2M + SZ_1M),
- .size = SZ_1M,
- },
-};
-
-static struct physmap_flash_data lb88rc8480_boot_flash_data = {
- .parts = lb88rc8480_boot_flash_parts,
- .nr_parts = ARRAY_SIZE(lb88rc8480_boot_flash_parts),
- .width = 1, /* 8 bit bus width */
-};
-
-static struct resource lb88rc8480_boot_flash_resource = {
- .flags = IORESOURCE_MEM,
- .start = LB88RC8480_NOR_BOOT_BASE,
- .end = LB88RC8480_NOR_BOOT_BASE + LB88RC8480_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device lb88rc8480_boot_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &lb88rc8480_boot_flash_data,
- },
- .num_resources = 1,
- .resource = &lb88rc8480_boot_flash_resource,
-};
-
-static struct mv643xx_eth_platform_data lb88rc8480_ge0_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(1),
- .mac_addr = { 0x00, 0x50, 0x43, 0x11, 0x22, 0x33 },
-};
-
-static void __init lb88rc8480_init(void)
-{
- /*
- * Basic setup. Needs to be called early.
- */
- loki_init();
-
- loki_ge0_init(&lb88rc8480_ge0_data);
- loki_sas_init();
- loki_uart0_init();
- loki_uart1_init();
-
- loki_setup_dev_boot_win(LB88RC8480_FLASH_BOOT_CS_BASE,
- LB88RC8480_FLASH_BOOT_CS_SIZE);
- platform_device_register(&lb88rc8480_boot_flash);
-}
-
-MACHINE_START(LB88RC8480, "Marvell LB88RC8480 Development Board")
- /* Maintainer: Ke Wei <kewei@marvell.com> */
- .boot_params = 0x00000100,
- .init_machine = lb88rc8480_init,
- .map_io = loki_map_io,
- .init_early = loki_init_early,
- .init_irq = loki_init_irq,
- .timer = &loki_timer,
-MACHINE_END
+++ /dev/null
-# Copyright 2007 Simtec Electronics
-#
-# Licensed under GPLv2
-
-menu "S3C2400 Machines"
-
-endmenu
+++ /dev/null
-# arch/arm/mach-s3c2400/Makefile
-#
-# Copyright 2007 Simtec Electronics
-#
-# Licensed under GPLv2
-
-obj-y :=
-obj-m :=
-obj-n :=
-obj- :=
-
-obj-$(CONFIG_CPU_S3C2400) += gpio.o
-
-# Machine support
-
+++ /dev/null
-/* linux/arch/arm/mach-s3c2400/gpio.c
- *
- * Copyright (c) 2006 Lucas Correia Villa Real <lucasvr@gobolinux.org>
- *
- * S3C2400 GPIO support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-*/
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <asm/irq.h>
-
-#include <mach/regs-gpio.h>
-
-int s3c2400_gpio_getirq(unsigned int pin)
-{
- if (pin < S3C2410_GPE(0) || pin > S3C2400_GPE(7))
- return -EINVAL; /* not valid interrupts */
-
- return (pin - S3C2410_GPE(0)) + IRQ_EINT0;
-}
-
-EXPORT_SYMBOL(s3c2400_gpio_getirq);
+++ /dev/null
-/* arch/arm/mach-s3c2400/include/mach/map.h
- *
- * Copyright 2003-2007 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- * Ben Dooks <ben@simtec.co.uk>
- *
- * Copyright 2003, Lucas Correia Villa Real
- *
- * S3C2400 - Memory map definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#define S3C2400_PA_MEMCTRL (0x14000000)
-#define S3C2400_PA_USBHOST (0x14200000)
-#define S3C2400_PA_IRQ (0x14400000)
-#define S3C2400_PA_DMA (0x14600000)
-#define S3C2400_PA_CLKPWR (0x14800000)
-#define S3C2400_PA_LCD (0x14A00000)
-#define S3C2400_PA_UART (0x15000000)
-#define S3C2400_PA_TIMER (0x15100000)
-#define S3C2400_PA_USBDEV (0x15200140)
-#define S3C2400_PA_WATCHDOG (0x15300000)
-#define S3C2400_PA_IIC (0x15400000)
-#define S3C2400_PA_IIS (0x15508000)
-#define S3C2400_PA_GPIO (0x15600000)
-#define S3C2400_PA_RTC (0x15700040)
-#define S3C2400_PA_ADC (0x15800000)
-#define S3C2400_PA_SPI (0x15900000)
-
-#define S3C2400_PA_MMC (0x15A00000)
-#define S3C2400_SZ_MMC SZ_1M
-
-/* physical addresses of all the chip-select areas */
-
-#define S3C2400_CS0 (0x00000000)
-#define S3C2400_CS1 (0x02000000)
-#define S3C2400_CS2 (0x04000000)
-#define S3C2400_CS3 (0x06000000)
-#define S3C2400_CS4 (0x08000000)
-#define S3C2400_CS5 (0x0A000000)
-#define S3C2400_CS6 (0x0C000000)
-#define S3C2400_CS7 (0x0E000000)
-
-#define S3C2400_SDRAM_PA (S3C2400_CS6)
-
-/* Use a single interface for common resources between S3C24XX cpus */
-
-#define S3C24XX_PA_IRQ S3C2400_PA_IRQ
-#define S3C24XX_PA_MEMCTRL S3C2400_PA_MEMCTRL
-#define S3C24XX_PA_USBHOST S3C2400_PA_USBHOST
-#define S3C24XX_PA_DMA S3C2400_PA_DMA
-#define S3C24XX_PA_CLKPWR S3C2400_PA_CLKPWR
-#define S3C24XX_PA_LCD S3C2400_PA_LCD
-#define S3C24XX_PA_UART S3C2400_PA_UART
-#define S3C24XX_PA_TIMER S3C2400_PA_TIMER
-#define S3C24XX_PA_USBDEV S3C2400_PA_USBDEV
-#define S3C24XX_PA_WATCHDOG S3C2400_PA_WATCHDOG
-#define S3C24XX_PA_IIC S3C2400_PA_IIC
-#define S3C24XX_PA_IIS S3C2400_PA_IIS
-#define S3C24XX_PA_GPIO S3C2400_PA_GPIO
-#define S3C24XX_PA_RTC S3C2400_PA_RTC
-#define S3C24XX_PA_ADC S3C2400_PA_ADC
-#define S3C24XX_PA_SPI S3C2400_PA_SPI
extern int s3c2410_gpio_getirq(unsigned int pin);
-#ifdef CONFIG_CPU_S3C2400
-
-extern int s3c2400_gpio_getirq(unsigned int pin);
-
-#endif /* CONFIG_CPU_S3C2400 */
-
/* s3c2410_gpio_irqfilter
*
* set the irq filtering on the given pin
#include <mach/gpio-nrs.h>
-#ifdef CONFIG_CPU_S3C2400
-#define S3C24XX_MISCCR S3C2400_MISCCR
-#else
#define S3C24XX_MISCCR S3C24XX_GPIOREG2(0x80)
-#endif /* CONFIG_CPU_S3C2400 */
/* general configuration options */
/* configure GPIO ports A..G */
/* port A - S3C2410: 22bits, zero in bit X makes pin X output
- * S3C2400: 18bits, zero in bit X makes pin X output
* 1 makes port special function, this is default
*/
#define S3C2410_GPACON S3C2410_GPIOREG(0x00)
#define S3C2410_GPADAT S3C2410_GPIOREG(0x04)
-#define S3C2400_GPACON S3C2410_GPIOREG(0x00)
-#define S3C2400_GPADAT S3C2410_GPIOREG(0x04)
-
#define S3C2410_GPA0_ADDR0 (1<<0)
-
#define S3C2410_GPA1_ADDR16 (1<<1)
-
#define S3C2410_GPA2_ADDR17 (1<<2)
-
#define S3C2410_GPA3_ADDR18 (1<<3)
-
#define S3C2410_GPA4_ADDR19 (1<<4)
-
#define S3C2410_GPA5_ADDR20 (1<<5)
-
#define S3C2410_GPA6_ADDR21 (1<<6)
-
#define S3C2410_GPA7_ADDR22 (1<<7)
-
#define S3C2410_GPA8_ADDR23 (1<<8)
-
#define S3C2410_GPA9_ADDR24 (1<<9)
-
#define S3C2410_GPA10_ADDR25 (1<<10)
-#define S3C2400_GPA10_SCKE (1<<10)
-
#define S3C2410_GPA11_ADDR26 (1<<11)
-#define S3C2400_GPA11_nCAS0 (1<<11)
-
#define S3C2410_GPA12_nGCS1 (1<<12)
-#define S3C2400_GPA12_nCAS1 (1<<12)
-
#define S3C2410_GPA13_nGCS2 (1<<13)
-#define S3C2400_GPA13_nGCS1 (1<<13)
-
#define S3C2410_GPA14_nGCS3 (1<<14)
-#define S3C2400_GPA14_nGCS2 (1<<14)
-
#define S3C2410_GPA15_nGCS4 (1<<15)
-#define S3C2400_GPA15_nGCS3 (1<<15)
-
#define S3C2410_GPA16_nGCS5 (1<<16)
-#define S3C2400_GPA16_nGCS4 (1<<16)
-
#define S3C2410_GPA17_CLE (1<<17)
-#define S3C2400_GPA17_nGCS5 (1<<17)
-
#define S3C2410_GPA18_ALE (1<<18)
-
#define S3C2410_GPA19_nFWE (1<<19)
-
#define S3C2410_GPA20_nFRE (1<<20)
-
#define S3C2410_GPA21_nRSTOUT (1<<21)
-
#define S3C2410_GPA22_nFCE (1<<22)
/* 0x08 and 0x0c are reserved on S3C2410 */
* GPB is 10 IO pins, each configured by 2 bits each in GPBCON.
* 00 = input, 01 = output, 10=special function, 11=reserved
- * S3C2400:
- * GPB is 16 IO pins, each configured by 2 bits each in GPBCON.
- * 00 = input, 01 = output, 10=data, 11=special function
-
* bit 0,1 = pin 0, 2,3= pin 1...
*
* CPBUP = pull up resistor control, 1=disabled, 0=enabled
#define S3C2410_GPBDAT S3C2410_GPIOREG(0x14)
#define S3C2410_GPBUP S3C2410_GPIOREG(0x18)
-#define S3C2400_GPBCON S3C2410_GPIOREG(0x08)
-#define S3C2400_GPBDAT S3C2410_GPIOREG(0x0C)
-#define S3C2400_GPBUP S3C2410_GPIOREG(0x10)
-
/* no i/o pin in port b can have value 3 (unless it is a s3c2443) ! */
#define S3C2410_GPB0_TOUT0 (0x02 << 0)
-#define S3C2400_GPB0_DATA16 (0x02 << 0)
#define S3C2410_GPB1_TOUT1 (0x02 << 2)
-#define S3C2400_GPB1_DATA17 (0x02 << 2)
#define S3C2410_GPB2_TOUT2 (0x02 << 4)
-#define S3C2400_GPB2_DATA18 (0x02 << 4)
-#define S3C2400_GPB2_TCLK1 (0x03 << 4)
#define S3C2410_GPB3_TOUT3 (0x02 << 6)
-#define S3C2400_GPB3_DATA19 (0x02 << 6)
-#define S3C2400_GPB3_TXD1 (0x03 << 6)
#define S3C2410_GPB4_TCLK0 (0x02 << 8)
-#define S3C2400_GPB4_DATA20 (0x02 << 8)
#define S3C2410_GPB4_MASK (0x03 << 8)
-#define S3C2400_GPB4_RXD1 (0x03 << 8)
-#define S3C2400_GPB4_MASK (0x03 << 8)
#define S3C2410_GPB5_nXBACK (0x02 << 10)
#define S3C2443_GPB5_XBACK (0x03 << 10)
-#define S3C2400_GPB5_DATA21 (0x02 << 10)
-#define S3C2400_GPB5_nCTS1 (0x03 << 10)
#define S3C2410_GPB6_nXBREQ (0x02 << 12)
#define S3C2443_GPB6_XBREQ (0x03 << 12)
-#define S3C2400_GPB6_DATA22 (0x02 << 12)
-#define S3C2400_GPB6_nRTS1 (0x03 << 12)
#define S3C2410_GPB7_nXDACK1 (0x02 << 14)
#define S3C2443_GPB7_XDACK1 (0x03 << 14)
-#define S3C2400_GPB7_DATA23 (0x02 << 14)
#define S3C2410_GPB8_nXDREQ1 (0x02 << 16)
-#define S3C2400_GPB8_DATA24 (0x02 << 16)
#define S3C2410_GPB9_nXDACK0 (0x02 << 18)
#define S3C2443_GPB9_XDACK0 (0x03 << 18)
-#define S3C2400_GPB9_DATA25 (0x02 << 18)
-#define S3C2400_GPB9_I2SSDI (0x03 << 18)
#define S3C2410_GPB10_nXDRE0 (0x02 << 20)
#define S3C2443_GPB10_XDREQ0 (0x03 << 20)
-#define S3C2400_GPB10_DATA26 (0x02 << 20)
-#define S3C2400_GPB10_nSS (0x03 << 20)
-
-#define S3C2400_GPB11_INP (0x00 << 22)
-#define S3C2400_GPB11_OUTP (0x01 << 22)
-#define S3C2400_GPB11_DATA27 (0x02 << 22)
-
-#define S3C2400_GPB12_INP (0x00 << 24)
-#define S3C2400_GPB12_OUTP (0x01 << 24)
-#define S3C2400_GPB12_DATA28 (0x02 << 24)
-
-#define S3C2400_GPB13_INP (0x00 << 26)
-#define S3C2400_GPB13_OUTP (0x01 << 26)
-#define S3C2400_GPB13_DATA29 (0x02 << 26)
-
-#define S3C2400_GPB14_INP (0x00 << 28)
-#define S3C2400_GPB14_OUTP (0x01 << 28)
-#define S3C2400_GPB14_DATA30 (0x02 << 28)
-
-#define S3C2400_GPB15_INP (0x00 << 30)
-#define S3C2400_GPB15_OUTP (0x01 << 30)
-#define S3C2400_GPB15_DATA31 (0x02 << 30)
#define S3C2410_GPB_PUPDIS(x) (1<<(x))
#define S3C2410_GPCCON S3C2410_GPIOREG(0x20)
#define S3C2410_GPCDAT S3C2410_GPIOREG(0x24)
#define S3C2410_GPCUP S3C2410_GPIOREG(0x28)
-
-#define S3C2400_GPCCON S3C2410_GPIOREG(0x14)
-#define S3C2400_GPCDAT S3C2410_GPIOREG(0x18)
-#define S3C2400_GPCUP S3C2410_GPIOREG(0x1C)
-
#define S3C2410_GPC0_LEND (0x02 << 0)
-#define S3C2400_GPC0_VD0 (0x02 << 0)
-
#define S3C2410_GPC1_VCLK (0x02 << 2)
-#define S3C2400_GPC1_VD1 (0x02 << 2)
-
#define S3C2410_GPC2_VLINE (0x02 << 4)
-#define S3C2400_GPC2_VD2 (0x02 << 4)
-
#define S3C2410_GPC3_VFRAME (0x02 << 6)
-#define S3C2400_GPC3_VD3 (0x02 << 6)
-
#define S3C2410_GPC4_VM (0x02 << 8)
-#define S3C2400_GPC4_VD4 (0x02 << 8)
-
#define S3C2410_GPC5_LCDVF0 (0x02 << 10)
-#define S3C2400_GPC5_VD5 (0x02 << 10)
-
#define S3C2410_GPC6_LCDVF1 (0x02 << 12)
-#define S3C2400_GPC6_VD6 (0x02 << 12)
-
#define S3C2410_GPC7_LCDVF2 (0x02 << 14)
-#define S3C2400_GPC7_VD7 (0x02 << 14)
-
#define S3C2410_GPC8_VD0 (0x02 << 16)
-#define S3C2400_GPC8_VD8 (0x02 << 16)
-
#define S3C2410_GPC9_VD1 (0x02 << 18)
-#define S3C2400_GPC9_VD9 (0x02 << 18)
-
#define S3C2410_GPC10_VD2 (0x02 << 20)
-#define S3C2400_GPC10_VD10 (0x02 << 20)
-
#define S3C2410_GPC11_VD3 (0x02 << 22)
-#define S3C2400_GPC11_VD11 (0x02 << 22)
-
#define S3C2410_GPC12_VD4 (0x02 << 24)
-#define S3C2400_GPC12_VD12 (0x02 << 24)
-
#define S3C2410_GPC13_VD5 (0x02 << 26)
-#define S3C2400_GPC13_VD13 (0x02 << 26)
-
#define S3C2410_GPC14_VD6 (0x02 << 28)
-#define S3C2400_GPC14_VD14 (0x02 << 28)
-
#define S3C2410_GPC15_VD7 (0x02 << 30)
-#define S3C2400_GPC15_VD15 (0x02 << 30)
-
#define S3C2410_GPC_PUPDIS(x) (1<<(x))
/*
* almost identical setup to port b, but the special functions are mostly
* to do with the video system's data.
*
- * S3C2400: Port D consists of 11 GPIO/Special function
- *
* almost identical setup to port c
*/
#define S3C2410_GPDDAT S3C2410_GPIOREG(0x34)
#define S3C2410_GPDUP S3C2410_GPIOREG(0x38)
-#define S3C2400_GPDCON S3C2410_GPIOREG(0x20)
-#define S3C2400_GPDDAT S3C2410_GPIOREG(0x24)
-#define S3C2400_GPDUP S3C2410_GPIOREG(0x28)
-
#define S3C2410_GPD0_VD8 (0x02 << 0)
-#define S3C2400_GPD0_VFRAME (0x02 << 0)
#define S3C2442_GPD0_nSPICS1 (0x03 << 0)
#define S3C2410_GPD1_VD9 (0x02 << 2)
-#define S3C2400_GPD1_VM (0x02 << 2)
#define S3C2442_GPD1_SPICLK1 (0x03 << 2)
#define S3C2410_GPD2_VD10 (0x02 << 4)
-#define S3C2400_GPD2_VLINE (0x02 << 4)
#define S3C2410_GPD3_VD11 (0x02 << 6)
-#define S3C2400_GPD3_VCLK (0x02 << 6)
#define S3C2410_GPD4_VD12 (0x02 << 8)
-#define S3C2400_GPD4_LEND (0x02 << 8)
#define S3C2410_GPD5_VD13 (0x02 << 10)
-#define S3C2400_GPD5_TOUT0 (0x02 << 10)
#define S3C2410_GPD6_VD14 (0x02 << 12)
-#define S3C2400_GPD6_TOUT1 (0x02 << 12)
#define S3C2410_GPD7_VD15 (0x02 << 14)
-#define S3C2400_GPD7_TOUT2 (0x02 << 14)
#define S3C2410_GPD8_VD16 (0x02 << 16)
-#define S3C2400_GPD8_TOUT3 (0x02 << 16)
#define S3C2440_GPD8_SPIMISO1 (0x03 << 16)
#define S3C2410_GPD9_VD17 (0x02 << 18)
-#define S3C2400_GPD9_TCLK0 (0x02 << 18)
#define S3C2440_GPD9_SPIMOSI1 (0x03 << 18)
#define S3C2410_GPD10_VD18 (0x02 << 20)
-#define S3C2400_GPD10_nWAIT (0x02 << 20)
#define S3C2440_GPD10_SPICLK1 (0x03 << 20)
#define S3C2410_GPD11_VD19 (0x02 << 22)
* again, the same as port B, but dealing with I2S, SDI, and
* more miscellaneous functions
*
- * S3C2400:
- * Port E consists of 12 GPIO/Special function
- *
* GPIO / interrupt inputs
*/
#define S3C2410_GPEDAT S3C2410_GPIOREG(0x44)
#define S3C2410_GPEUP S3C2410_GPIOREG(0x48)
-#define S3C2400_GPECON S3C2410_GPIOREG(0x2C)
-#define S3C2400_GPEDAT S3C2410_GPIOREG(0x30)
-#define S3C2400_GPEUP S3C2410_GPIOREG(0x34)
-
#define S3C2410_GPE0_I2SLRCK (0x02 << 0)
#define S3C2443_GPE0_AC_nRESET (0x03 << 0)
-#define S3C2400_GPE0_EINT0 (0x02 << 0)
#define S3C2410_GPE0_MASK (0x03 << 0)
#define S3C2410_GPE1_I2SSCLK (0x02 << 2)
#define S3C2443_GPE1_AC_SYNC (0x03 << 2)
-#define S3C2400_GPE1_EINT1 (0x02 << 2)
-#define S3C2400_GPE1_nSS (0x03 << 2)
#define S3C2410_GPE1_MASK (0x03 << 2)
#define S3C2410_GPE2_CDCLK (0x02 << 4)
#define S3C2443_GPE2_AC_BITCLK (0x03 << 4)
-#define S3C2400_GPE2_EINT2 (0x02 << 4)
-#define S3C2400_GPE2_I2SSDI (0x03 << 4)
#define S3C2410_GPE3_I2SSDI (0x02 << 6)
#define S3C2443_GPE3_AC_SDI (0x03 << 6)
-#define S3C2400_GPE3_EINT3 (0x02 << 6)
-#define S3C2400_GPE3_nCTS1 (0x03 << 6)
#define S3C2410_GPE3_nSS0 (0x03 << 6)
#define S3C2410_GPE3_MASK (0x03 << 6)
#define S3C2410_GPE4_I2SSDO (0x02 << 8)
#define S3C2443_GPE4_AC_SDO (0x03 << 8)
-#define S3C2400_GPE4_EINT4 (0x02 << 8)
-#define S3C2400_GPE4_nRTS1 (0x03 << 8)
#define S3C2410_GPE4_I2SSDI (0x03 << 8)
#define S3C2410_GPE4_MASK (0x03 << 8)
#define S3C2410_GPE5_SDCLK (0x02 << 10)
#define S3C2443_GPE5_SD1_CLK (0x02 << 10)
-#define S3C2400_GPE5_EINT5 (0x02 << 10)
-#define S3C2400_GPE5_TCLK1 (0x03 << 10)
#define S3C2443_GPE5_AC_BITCLK (0x03 << 10)
#define S3C2410_GPE6_SDCMD (0x02 << 12)
#define S3C2443_GPE6_SD1_CMD (0x02 << 12)
#define S3C2443_GPE6_AC_SDI (0x03 << 12)
-#define S3C2400_GPE6_EINT6 (0x02 << 12)
#define S3C2410_GPE7_SDDAT0 (0x02 << 14)
#define S3C2443_GPE5_SD1_DAT0 (0x02 << 14)
#define S3C2443_GPE7_AC_SDO (0x03 << 14)
-#define S3C2400_GPE7_EINT7 (0x02 << 14)
#define S3C2410_GPE8_SDDAT1 (0x02 << 16)
#define S3C2443_GPE8_SD1_DAT1 (0x02 << 16)
#define S3C2443_GPE8_AC_SYNC (0x03 << 16)
-#define S3C2400_GPE8_nXDACK0 (0x02 << 16)
#define S3C2410_GPE9_SDDAT2 (0x02 << 18)
#define S3C2443_GPE9_SD1_DAT2 (0x02 << 18)
#define S3C2443_GPE9_AC_nRESET (0x03 << 18)
-#define S3C2400_GPE9_nXDACK1 (0x02 << 18)
-#define S3C2400_GPE9_nXBACK (0x03 << 18)
#define S3C2410_GPE10_SDDAT3 (0x02 << 20)
#define S3C2443_GPE10_SD1_DAT3 (0x02 << 20)
-#define S3C2400_GPE10_nXDREQ0 (0x02 << 20)
#define S3C2410_GPE11_SPIMISO0 (0x02 << 22)
-#define S3C2400_GPE11_nXDREQ1 (0x02 << 22)
-#define S3C2400_GPE11_nXBREQ (0x03 << 22)
#define S3C2410_GPE12_SPIMOSI0 (0x02 << 24)
*
* pull up works like all other ports.
*
- * S3C2400:
- * Port F consists of 7 GPIO/Special function
- *
* GPIO/serial/misc pins
*/
#define S3C2410_GPFDAT S3C2410_GPIOREG(0x54)
#define S3C2410_GPFUP S3C2410_GPIOREG(0x58)
-#define S3C2400_GPFCON S3C2410_GPIOREG(0x38)
-#define S3C2400_GPFDAT S3C2410_GPIOREG(0x3C)
-#define S3C2400_GPFUP S3C2410_GPIOREG(0x40)
-
#define S3C2410_GPF0_EINT0 (0x02 << 0)
-#define S3C2400_GPF0_RXD0 (0x02 << 0)
-
#define S3C2410_GPF1_EINT1 (0x02 << 2)
-#define S3C2400_GPF1_RXD1 (0x02 << 2)
-#define S3C2400_GPF1_IICSDA (0x03 << 2)
-
#define S3C2410_GPF2_EINT2 (0x02 << 4)
-#define S3C2400_GPF2_TXD0 (0x02 << 4)
-
#define S3C2410_GPF3_EINT3 (0x02 << 6)
-#define S3C2400_GPF3_TXD1 (0x02 << 6)
-#define S3C2400_GPF3_IICSCL (0x03 << 6)
-
#define S3C2410_GPF4_EINT4 (0x02 << 8)
-#define S3C2400_GPF4_nRTS0 (0x02 << 8)
-#define S3C2400_GPF4_nXBACK (0x03 << 8)
-
#define S3C2410_GPF5_EINT5 (0x02 << 10)
-#define S3C2400_GPF5_nCTS0 (0x02 << 10)
-#define S3C2400_GPF5_nXBREQ (0x03 << 10)
-
#define S3C2410_GPF6_EINT6 (0x02 << 12)
-#define S3C2400_GPF6_CLKOUT (0x02 << 12)
-
#define S3C2410_GPF7_EINT7 (0x02 << 14)
-
#define S3C2410_GPF_PUPDIS(x) (1<<(x))
/* S3C2410:
* 00 = 0 input, 1 output, 2 interrupt (EINT0..7), 3 special func
*
* pull up works like all other ports.
- *
- * S3C2400:
- * Port G consists of 10 GPIO/Special function
*/
#define S3C2410_GPGCON S3C2410_GPIOREG(0x60)
#define S3C2410_GPGDAT S3C2410_GPIOREG(0x64)
#define S3C2410_GPGUP S3C2410_GPIOREG(0x68)
-#define S3C2400_GPGCON S3C2410_GPIOREG(0x44)
-#define S3C2400_GPGDAT S3C2410_GPIOREG(0x48)
-#define S3C2400_GPGUP S3C2410_GPIOREG(0x4C)
-
#define S3C2410_GPG0_EINT8 (0x02 << 0)
-#define S3C2400_GPG0_I2SLRCK (0x02 << 0)
#define S3C2410_GPG1_EINT9 (0x02 << 2)
-#define S3C2400_GPG1_I2SSCLK (0x02 << 2)
#define S3C2410_GPG2_EINT10 (0x02 << 4)
#define S3C2410_GPG2_nSS0 (0x03 << 4)
-#define S3C2400_GPG2_CDCLK (0x02 << 4)
#define S3C2410_GPG3_EINT11 (0x02 << 6)
#define S3C2410_GPG3_nSS1 (0x03 << 6)
-#define S3C2400_GPG3_I2SSDO (0x02 << 6)
-#define S3C2400_GPG3_I2SSDI (0x03 << 6)
#define S3C2410_GPG4_EINT12 (0x02 << 8)
-#define S3C2400_GPG4_MMCCLK (0x02 << 8)
-#define S3C2400_GPG4_I2SSDI (0x03 << 8)
#define S3C2410_GPG4_LCDPWREN (0x03 << 8)
#define S3C2443_GPG4_LCDPWRDN (0x03 << 8)
#define S3C2410_GPG5_EINT13 (0x02 << 10)
-#define S3C2400_GPG5_MMCCMD (0x02 << 10)
-#define S3C2400_GPG5_IICSDA (0x03 << 10)
#define S3C2410_GPG5_SPIMISO1 (0x03 << 10) /* not s3c2443 */
#define S3C2410_GPG6_EINT14 (0x02 << 12)
-#define S3C2400_GPG6_MMCDAT (0x02 << 12)
-#define S3C2400_GPG6_IICSCL (0x03 << 12)
#define S3C2410_GPG6_SPIMOSI1 (0x03 << 12)
#define S3C2410_GPG7_EINT15 (0x02 << 14)
#define S3C2410_GPG7_SPICLK1 (0x03 << 14)
-#define S3C2400_GPG7_SPIMISO (0x02 << 14)
-#define S3C2400_GPG7_IICSDA (0x03 << 14)
#define S3C2410_GPG8_EINT16 (0x02 << 16)
-#define S3C2400_GPG8_SPIMOSI (0x02 << 16)
-#define S3C2400_GPG8_IICSCL (0x03 << 16)
#define S3C2410_GPG9_EINT17 (0x02 << 18)
-#define S3C2400_GPG9_SPICLK (0x02 << 18)
-#define S3C2400_GPG9_MMCCLK (0x03 << 18)
#define S3C2410_GPG10_EINT18 (0x02 << 20)
#define S3C2443_GPMUP S3C2410_GPIOREG(0x108)
/* miscellaneous control */
-#define S3C2400_MISCCR S3C2410_GPIOREG(0x54)
#define S3C2410_MISCCR S3C2410_GPIOREG(0x80)
#define S3C2410_DCLKCON S3C2410_GPIOREG(0x84)
#define S3C2410_MISCCR_SPUCR_LEN (0<<1)
#define S3C2410_MISCCR_SPUCR_LDIS (1<<1)
-#define S3C2400_MISCCR_SPUCR_LEN (0<<0)
-#define S3C2400_MISCCR_SPUCR_LDIS (1<<0)
-#define S3C2400_MISCCR_SPUCR_HEN (0<<1)
-#define S3C2400_MISCCR_SPUCR_HDIS (1<<1)
-
-#define S3C2400_MISCCR_HZ_STOPEN (0<<2)
-#define S3C2400_MISCCR_HZ_STOPPREV (1<<2)
-
#define S3C2410_MISCCR_USBDEV (0<<3)
#define S3C2410_MISCCR_USBHOST (1<<3)
*
* Samsung datasheet p9-25
*/
-#define S3C2400_EXTINT0 S3C2410_GPIOREG(0x58)
#define S3C2410_EXTINT0 S3C2410_GPIOREG(0x88)
#define S3C2410_EXTINT1 S3C2410_GPIOREG(0x8C)
#define S3C2410_EXTINT2 S3C2410_GPIOREG(0x90)
#define S3C2410_GSTATUS2_OFFRESET (1<<1)
#define S3C2410_GSTATUS2_PONRESET (1<<0)
-/* open drain control register */
-#define S3C2400_OPENCR S3C2410_GPIOREG(0x50)
-
-#define S3C2400_OPENCR_OPC_RXD1DIS (0<<0)
-#define S3C2400_OPENCR_OPC_RXD1EN (1<<0)
-#define S3C2400_OPENCR_OPC_TXD1DIS (0<<1)
-#define S3C2400_OPENCR_OPC_TXD1EN (1<<1)
-#define S3C2400_OPENCR_OPC_CMDDIS (0<<2)
-#define S3C2400_OPENCR_OPC_CMDEN (1<<2)
-#define S3C2400_OPENCR_OPC_DATDIS (0<<3)
-#define S3C2400_OPENCR_OPC_DATEN (1<<3)
-#define S3C2400_OPENCR_OPC_MISODIS (0<<4)
-#define S3C2400_OPENCR_OPC_MISOEN (1<<4)
-#define S3C2400_OPENCR_OPC_MOSIDIS (0<<5)
-#define S3C2400_OPENCR_OPC_MOSIEN (1<<5)
-
/* 2412/2413 sleep configuration registers */
#define S3C2412_GPBSLPCON S3C2410_GPIOREG(0x1C)
#define S3C2410_BANKCON_Tacs_SHIFT (13)
#define S3C2410_BANKCON_SRAM (0x0 << 15)
-#define S3C2400_BANKCON_EDODRAM (0x2 << 15)
#define S3C2410_BANKCON_SDRAM (0x3 << 15)
-/* next bits only for EDO DRAM in 6,7 */
-#define S3C2400_BANKCON_EDO_Trcd1 (0x00 << 4)
-#define S3C2400_BANKCON_EDO_Trcd2 (0x01 << 4)
-#define S3C2400_BANKCON_EDO_Trcd3 (0x02 << 4)
-#define S3C2400_BANKCON_EDO_Trcd4 (0x03 << 4)
-
-/* CAS pulse width */
-#define S3C2400_BANKCON_EDO_PULSE1 (0x00 << 3)
-#define S3C2400_BANKCON_EDO_PULSE2 (0x01 << 3)
-
-/* CAS pre-charge */
-#define S3C2400_BANKCON_EDO_TCP1 (0x00 << 2)
-#define S3C2400_BANKCON_EDO_TCP2 (0x01 << 2)
-
-/* control column address select */
-#define S3C2400_BANKCON_EDO_SCANb8 (0x00 << 0)
-#define S3C2400_BANKCON_EDO_SCANb9 (0x01 << 0)
-#define S3C2400_BANKCON_EDO_SCANb10 (0x02 << 0)
-#define S3C2400_BANKCON_EDO_SCANb11 (0x03 << 0)
-
/* next bits only for SDRAM in 6,7 */
#define S3C2410_BANKCON_Trcd2 (0x00 << 2)
#define S3C2410_BANKCON_Trcd3 (0x01 << 2)
#define S3C2410_REFRESH_TRP_3clk (1<<20)
#define S3C2410_REFRESH_TRP_4clk (2<<20)
-#define S3C2400_REFRESH_DRAM_TRP_MASK (3<<20)
-#define S3C2400_REFRESH_DRAM_TRP_1_5clk (0<<20)
-#define S3C2400_REFRESH_DRAM_TRP_2_5clk (1<<20)
-#define S3C2400_REFRESH_DRAM_TRP_3_5clk (2<<20)
-#define S3C2400_REFRESH_DRAM_TRP_4_5clk (3<<20)
-
#define S3C2410_REFRESH_TSRC_MASK (3<<18)
#define S3C2410_REFRESH_TSRC_4clk (0<<18)
#define S3C2410_REFRESH_TSRC_5clk (1<<18)
#define S3C2410_BANKSIZE_4M (0x5 << 0)
#define S3C2410_BANKSIZE_2M (0x4 << 0)
#define S3C2410_BANKSIZE_MASK (0x7 << 0)
-#define S3C2400_BANKSIZE_MASK (0x4 << 0)
#define S3C2410_BANKSIZE_SCLK_EN (1<<4)
#define S3C2410_BANKSIZE_SCKE_EN (1<<5)
#define S3C2410_BANKSIZE_BURST (1<<7)
config CPU_S3C2412_ONLY
bool
- depends on ARCH_S3C2410 && !CPU_S3C2400 && !CPU_S3C2410 && \
+ depends on ARCH_S3C2410 && !CPU_S3C2410 && \
!CPU_S3C2416 && !CPU_S3C2440 && !CPU_S3C2442 && \
!CPU_S3C2443 && CPU_S3C2412
default y if CPU_S3C2412
+++ /dev/null
-/* arch/arm/mach-s3c2410/include/mach/debug-macro.S
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/* pull in the relevant register and map files. */
-
-#include <mach/map.h>
-#include <plat/regs-serial.h>
-
- .macro addruart, rp, rv
- ldr \rp, = S3C24XX_PA_UART
- ldr \rv, = S3C24XX_VA_UART
-#if CONFIG_DEBUG_S3C_UART != 0
- add \rp, \rp, #(S3C2410_UART1_OFF * CONFIG_DEBUG_S3C_UART)
- add \rv, \rv, #(S3C2410_UART1_OFF * CONFIG_DEBUG_S3C_UART)
-#endif
- .endm
-
-/* include the reset of the code which will do the work, we're only
- * compiling for a single cpu processor type so the default of s3c2440
- * will be fine with us.
- */
-
-#include <plat/debug-macro.S>
+++ /dev/null
-/* arch/arm/mach-s3c24a0/include/mach/io.h
- *
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben-linux@fluff.org>
- *
- * Default IO routines for S3C24A0
- */
-
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-/* No current ISA/PCI bus support. */
-#define __io(a) __typesafe_io(a)
-#define __mem_pci(a) (a)
-
-#define IO_SPACE_LIMIT (0xFFFFFFFF)
-
-#endif
+++ /dev/null
-/* linux/arch/arm/mach-s3c24a0/include/mach/irqs.h
- *
- * Copyright (c) 2003-2005 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-
-#ifndef __ASM_ARCH_24A0_IRQS_H
-#define __ASM_ARCH_24A0_IRQS_H __FILE__
-
-#define IRQ_EINT0t2 S3C2410_IRQ(0) /* 16 */
-/* for generic entry-macro.S */
-#define IRQ_EINT0 IRQ_EINT0t2
-
-#define IRQ_EINT3t6 S3C2410_IRQ(1)
-#define IRQ_EINT7t10 S3C2410_IRQ(2)
-#define IRQ_EINT11t14 S3C2410_IRQ(3)
-#define IRQ_EINT15t18 S3C2410_IRQ(4) /* 20 */
-#define IRQ_TICK S3C2410_IRQ(5)
-#define IRQ_DCTQ S3C2410_IRQ(6)
-#define IRQ_MC S3C2410_IRQ(7)
-#define IRQ_ME S3C2410_IRQ(8) /* 24 */
-#define IRQ_KEYPAD S3C2410_IRQ(9)
-#define IRQ_TIMER0 S3C2410_IRQ(10)
-#define IRQ_TIMER1 S3C2410_IRQ(11)
-#define IRQ_TIMER2 S3C2410_IRQ(12)
-#define IRQ_TIMER3_4 S3C2410_IRQ(13)
-#define IRQ_OS_TIMER IRQ_TIMER3_4
-#define IRQ_LCD S3C2410_IRQ(14)
-#define IRQ_CAM_C S3C2410_IRQ(15)
-#define IRQ_WDT_BATFLT S3C2410_IRQ(16) /* 32 */
-#define IRQ_UART0 S3C2410_IRQ(17)
-#define IRQ_CAM_P S3C2410_IRQ(18)
-#define IRQ_MODEM S3C2410_IRQ(19)
-#define IRQ_DMA S3C2410_IRQ(20)
-#define IRQ_SDI S3C2410_IRQ(21)
-#define IRQ_SPI0 S3C2410_IRQ(22)
-#define IRQ_UART1 S3C2410_IRQ(23)
-#define IRQ_AC97_NFLASH S3C2410_IRQ(24) /* 40 */
-#define IRQ_USBD S3C2410_IRQ(25)
-#define IRQ_USBH S3C2410_IRQ(26)
-#define IRQ_IIC S3C2410_IRQ(27)
-#define IRQ_IRDA_MSTICK S3C2410_IRQ(28) /* 44 */
-#define IRQ_VLX_SPI1 S3C2410_IRQ(29)
-#define IRQ_RTC S3C2410_IRQ(30) /* 46 */
-#define IRQ_ADC_PEN S3C2410_IRQ(31)
-
-/* interrupts generated from the external interrupts sources */
-#define IRQ_EINT00 S3C2410_IRQ(32) /* 48 */
-#define IRQ_EINT1 S3C2410_IRQ(33)
-#define IRQ_EINT2 S3C2410_IRQ(34)
-#define IRQ_EINT3 S3C2410_IRQ(35)
-#define IRQ_EINT4 S3C2410_IRQ(36)
-#define IRQ_EINT5 S3C2410_IRQ(37)
-#define IRQ_EINT6 S3C2410_IRQ(38)
-#define IRQ_EINT7 S3C2410_IRQ(39)
-#define IRQ_EINT8 S3C2410_IRQ(40)
-#define IRQ_EINT9 S3C2410_IRQ(41)
-#define IRQ_EINT10 S3C2410_IRQ(42)
-#define IRQ_EINT11 S3C2410_IRQ(43)
-#define IRQ_EINT12 S3C2410_IRQ(44)
-#define IRQ_EINT13 S3C2410_IRQ(45)
-#define IRQ_EINT14 S3C2410_IRQ(46)
-#define IRQ_EINT15 S3C2410_IRQ(47)
-#define IRQ_EINT16 S3C2410_IRQ(48)
-#define IRQ_EINT17 S3C2410_IRQ(49)
-#define IRQ_EINT18 S3C2410_IRQ(50)
-
-#define IRQ_EINT_BIT(x) ((x) - IRQ_EINT00)
-
-/* SUB IRQS */
-#define IRQ_S3CUART_RX0 S3C2410_IRQ(51) /* 67 */
-#define IRQ_S3CUART_TX0 S3C2410_IRQ(52)
-#define IRQ_S3CUART_ERR0 S3C2410_IRQ(53)
-
-#define IRQ_S3CUART_RX1 S3C2410_IRQ(54)
-#define IRQ_S3CUART_TX1 S3C2410_IRQ(55)
-#define IRQ_S3CUART_ERR1 S3C2410_IRQ(56)
-
-#define IRQ_S3CUART_RX2 (0x0)
-#define IRQ_S3CUART_TX2 (0x0)
-#define IRQ_S3CUART_ERR2 (0x0)
-
-
-#define IRQ_IRDA S3C2410_IRQ(57)
-#define IRQ_MSTICK S3C2410_IRQ(58)
-#define IRQ_RESERVED0 S3C2410_IRQ(59)
-#define IRQ_RESERVED1 S3C2410_IRQ(60)
-#define IRQ_RESERVED2 S3C2410_IRQ(61)
-#define IRQ_TIMER3 S3C2410_IRQ(62)
-#define IRQ_TIMER4 S3C2410_IRQ(63)
-#define IRQ_WDT S3C2410_IRQ(64)
-#define IRQ_BATFLT S3C2410_IRQ(65)
-#define IRQ_POST S3C2410_IRQ(66)
-#define IRQ_DISP_FIFO S3C2410_IRQ(67)
-#define IRQ_PENUP S3C2410_IRQ(68)
-#define IRQ_PENDN S3C2410_IRQ(69)
-#define IRQ_ADC S3C2410_IRQ(70)
-#define IRQ_DISP_FRAME S3C2410_IRQ(71)
-#define IRQ_NFLASH S3C2410_IRQ(72)
-#define IRQ_AC97 S3C2410_IRQ(73)
-#define IRQ_SPI1 S3C2410_IRQ(74)
-#define IRQ_VLX S3C2410_IRQ(75)
-#define IRQ_DMA0 S3C2410_IRQ(76)
-#define IRQ_DMA1 S3C2410_IRQ(77)
-#define IRQ_DMA2 S3C2410_IRQ(78)
-#define IRQ_DMA3 S3C2410_IRQ(79)
-
-#define IRQ_TC (0x0)
-
-#define NR_IRQS (IRQ_DMA3+1)
-
-#endif /* __ASM_ARCH_24A0_IRQS_H */
+++ /dev/null
-/* linux/arch/arm/mach-s3c24a0/include/mach/map.h
- *
- * Copyright 2003-2007 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C24A0 - Memory map definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_24A0_MAP_H
-#define __ASM_ARCH_24A0_MAP_H __FILE__
-
-#include <plat/map-base.h>
-#include <plat/map.h>
-
-#define S3C24A0_PA_IO_BASE (0x40000000)
-#define S3C24A0_PA_CLKPWR (0x40000000)
-#define S3C24A0_PA_IRQ (0x40200000)
-#define S3C24A0_PA_DMA (0x40400000)
-#define S3C24A0_PA_MEMCTRL (0x40C00000)
-#define S3C24A0_PA_NAND (0x40C00000)
-#define S3C24A0_PA_SROM (0x40C20000)
-#define S3C24A0_PA_SDRAM (0x40C40000)
-#define S3C24A0_PA_BUSM (0x40CE0000)
-#define S3C24A0_PA_USBHOST (0x41000000)
-#define S3C24A0_PA_MODEMIF (0x41180000)
-#define S3C24A0_PA_IRDA (0x41800000)
-#define S3C24A0_PA_TIMER (0x44000000)
-#define S3C24A0_PA_WATCHDOG (0x44100000)
-#define S3C24A0_PA_RTC (0x44200000)
-#define S3C24A0_PA_UART (0x44400000)
-#define S3C24A0_PA_UART0 (S3C24A0_PA_UART)
-#define S3C24A0_PA_UART1 (S3C24A0_PA_UART + 0x4000)
-#define S3C24A0_PA_SPI (0x44500000)
-#define S3C24A0_PA_IIC (0x44600000)
-#define S3C24A0_PA_IIS (0x44700000)
-#define S3C24A0_PA_GPIO (0x44800000)
-#define S3C24A0_PA_KEYIF (0x44900000)
-#define S3C24A0_PA_USBDEV (0x44A00000)
-#define S3C24A0_PA_AC97 (0x45000000)
-#define S3C24A0_PA_ADC (0x45800000)
-#define S3C24A0_PA_SDI (0x46000000)
-#define S3C24A0_PA_MS (0x46100000)
-#define S3C24A0_PA_LCD (0x4A000000)
-#define S3C24A0_PA_VPOST (0x4A100000)
-
-/* physical addresses of all the chip-select areas */
-
-#define S3C24A0_CS0 (0x00000000)
-#define S3C24A0_CS1 (0x04000000)
-#define S3C24A0_CS2 (0x08000000)
-#define S3C24A0_CS3 (0x0C000000)
-#define S3C24A0_CS4 (0x10000000)
-#define S3C24A0_CS5 (0x40000000)
-
-#define S3C24A0_SDRAM_PA (S3C24A0_CS4)
-
-/* Use a single interface for common resources between S3C24XX cpus */
-
-#define S3C24XX_PA_IRQ S3C24A0_PA_IRQ
-#define S3C24XX_PA_MEMCTRL S3C24A0_PA_MEMCTRL
-#define S3C24XX_PA_USBHOST S3C24A0_PA_USBHOST
-#define S3C24XX_PA_DMA S3C24A0_PA_DMA
-#define S3C24XX_PA_CLKPWR S3C24A0_PA_CLKPWR
-#define S3C24XX_PA_LCD S3C24A0_PA_LCD
-#define S3C24XX_PA_UART S3C24A0_PA_UART
-#define S3C24XX_PA_TIMER S3C24A0_PA_TIMER
-#define S3C24XX_PA_USBDEV S3C24A0_PA_USBDEV
-#define S3C24XX_PA_WATCHDOG S3C24A0_PA_WATCHDOG
-#define S3C24XX_PA_IIS S3C24A0_PA_IIS
-#define S3C24XX_PA_GPIO S3C24A0_PA_GPIO
-#define S3C24XX_PA_RTC S3C24A0_PA_RTC
-#define S3C24XX_PA_ADC S3C24A0_PA_ADC
-#define S3C24XX_PA_SPI S3C24A0_PA_SPI
-#define S3C24XX_PA_SDI S3C24A0_PA_SDI
-#define S3C24XX_PA_NAND S3C24A0_PA_NAND
-
-#define S3C_PA_UART S3C24A0_PA_UART
-#define S3C_PA_IIC S3C24A0_PA_IIC
-#define S3C_PA_NAND S3C24XX_PA_NAND
-
-#endif /* __ASM_ARCH_24A0_MAP_H */
+++ /dev/null
-/* linux/arch/arm/mach-s3c24a0/include/mach/memory.h
- * from linux/include/asm-arm/arch-rpc/memory.h
- *
- * Copyright (C) 1996,1997,1998 Russell King.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_24A0_MEMORY_H
-#define __ASM_ARCH_24A0_MEMORY_H __FILE__
-
-#define PLAT_PHYS_OFFSET UL(0x10000000)
-
-#define __virt_to_bus(x) __virt_to_phys(x)
-#define __bus_to_virt(x) __phys_to_virt(x)
-#define __pfn_to_bus(x) __pfn_to_phys(x)
-#define __bus_to_pfn(x) __phys_to_pfn(x)
-
-#endif
+++ /dev/null
-/* linux/arch/arm/mach-s3c24a0/include/mach/regs-clock.h
- *
- * Copyright (c) 2003-2006 Simtec Electronics <linux@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * S3C24A0 clock register definitions
-*/
-
-#ifndef __ASM_ARCH_24A0_REGS_CLOCK_H
-#define __ASM_ARCH_24A0_REGS_CLOCK_H __FILE__
-
-#define S3C24A0_MPLLCON S3C2410_CLKREG(0x10)
-#define S3C24A0_UPLLCON S3C2410_CLKREG(0x14)
-#define S3C24A0_CLKCON S3C2410_CLKREG(0x20)
-#define S3C24A0_CLKSRC S3C2410_CLKREG(0x24)
-#define S3C24A0_CLKDIVN S3C2410_CLKREG(0x28)
-
-/* CLKCON register bits */
-
-#define S3C24A0_CLKCON_VLX (1<<29)
-#define S3C24A0_CLKCON_VPOST (1<<28)
-#define S3C24A0_CLKCON_WDT (1<<27) /* reserved */
-#define S3C24A0_CLKCON_MPEGDCTQ (1<<26)
-#define S3C24A0_CLKCON_VPOSTIF (1<<25)
-#define S3C24A0_CLKCON_MPEG4IF (1<<24)
-#define S3C24A0_CLKCON_CAM_UPLL (1<<23)
-#define S3C24A0_CLKCON_LCDC (1<<22)
-#define S3C24A0_CLKCON_CAM_HCLK (1<<21)
-#define S3C24A0_CLKCON_MPEG4 (1<<20)
-#define S3C24A0_CLKCON_KEYPAD (1<<19)
-#define S3C24A0_CLKCON_ADC (1<<18)
-#define S3C24A0_CLKCON_SDI (1<<17)
-#define S3C24A0_CLKCON_MS (1<<16) /* memory stick */
-#define S3C24A0_CLKCON_USBD (1<<15)
-#define S3C24A0_CLKCON_GPIO (1<<14)
-#define S3C24A0_CLKCON_IIS (1<<13)
-#define S3C24A0_CLKCON_IIC (1<<12)
-#define S3C24A0_CLKCON_SPI (1<<11)
-#define S3C24A0_CLKCON_UART1 (1<<10)
-#define S3C24A0_CLKCON_UART0 (1<<9)
-#define S3C24A0_CLKCON_PWMT (1<<8)
-#define S3C24A0_CLKCON_USBH (1<<7)
-#define S3C24A0_CLKCON_AC97 (1<<6)
-#define S3C24A0_CLKCON_IrDA (1<<4)
-#define S3C24A0_CLKCON_IDLE (1<<2)
-#define S3C24A0_CLKCON_MON (1<<1)
-#define S3C24A0_CLKCON_STOP (1<<0)
-
-/* CLKSRC register bits */
-
-#define S3C24A0_CLKSRC_OSC (1<<8) /* CLKSRC */
-#define S3C24A0_CLKSRC_UPLL (1<<7)
-#define S3C24A0_CLKSRC_MPLL (1<<5)
-#define S3C24A0_CLKSRC_EXT (1<<4)
-
-/* Use a single interface with the common code, for s3c24xx */
-
-#define S3C2410_MPLLCON S3C24A0_MPLLCON
-#define S3C2410_UPLLCON S3C24A0_UPLLCON
-#define S3C2410_CLKCON S3C24A0_CLKCON
-#define S3C2410_CLKSLOW S3C24A0_CLKSRC
-#define S3C2410_CLKDIVN S3C24A0_CLKDIVN
-
-#define S3C2410_CLKCON_IDLE S3C24A0_CLKCON_IDLE
-#define S3C2410_CLKCON_POWER S3C24A0_CLKCON_STOP
-#define S3C2410_CLKCON_LCDC S3C24A0_CLKCON_LCDC
-#define S3C2410_CLKCON_USBH S3C24A0_CLKCON_USBH
-#define S3C2410_CLKCON_USBD S3C24A0_CLKCON_USBD
-#define S3C2410_CLKCON_PWMT S3C24A0_CLKCON_PWMT
-#define S3C2410_CLKCON_SDI S3C24A0_CLKCON_SDI
-#define S3C2410_CLKCON_UART0 S3C24A0_CLKCON_UART0
-#define S3C2410_CLKCON_UART1 S3C24A0_CLKCON_UART1
-#define S3C2410_CLKCON_GPIO S3C24A0_CLKCON_GPIO
-#define S3C2410_CLKCON_ADC S3C24A0_CLKCON_ADC
-#define S3C2410_CLKCON_IIC S3C24A0_CLKCON_IIC
-#define S3C2410_CLKCON_IIS S3C24A0_CLKCON_IIS
-#define S3C2410_CLKCON_SPI S3C24A0_CLKCON_SPI
-
-#define S3C2410_CLKSLOW_UCLK_OFF S3C24A0_CLKSRC_UPLL
-#define S3C2410_CLKSLOW_MPLL_OFF S3C24A0_CLKSRC_MPLL
-#define S3C2410_CLKSLOW_SLOW (0xFF)
-#define S3C2410_CLKSLOW_GET_SLOWVAL(x) (0x1)
-
-#endif /* __ASM_ARCH_24A0_REGS_CLOCK_H */
+++ /dev/null
-/* linux/arch/arm/mach-s3c24a0/include/mach/regs-irq.h
- *
- * Copyright (c) 2003 Simtec Electronics <linux@simtec.co.uk>
- * http://www.simtec.co.uk/products/SWLINUX/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-
-#ifndef ___ASM_ARCH_24A0_REGS_IRQ_H
-#define ___ASM_ARCH_24A0_REGS_IRQ_H __FILE__
-
-
-#define S3C2410_EINTMASK S3C2410_EINTREG(0x034)
-#define S3C2410_EINTPEND S3C2410_EINTREG(0X038)
-
-#define S3C24XX_EINTMASK S3C24XX_EINTREG(0x034)
-#define S3C24XX_EINTPEND S3C24XX_EINTREG(0X038)
-
-#endif /* __ASM_ARCH_24A0_REGS_IRQ_H */
-
-
-
+++ /dev/null
-/* linux/arch/arm/mach-s3c24a0/include/mach/system.h
- *
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C24A0 - System function defines and includes
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <mach/hardware.h>
-#include <asm/io.h>
-
-#include <mach/map.h>
-
-static void arch_idle(void)
-{
- /* currently no specific idle support. */
-}
-
-void (*s3c24xx_reset_hook)(void);
-
-#include <asm/plat-s3c24xx/system-reset.h>
+++ /dev/null
-/* linux/arch/arm/mach-s3c24a0/include/mach/tick.h
- *
- * Copyright 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- * http://armlinux.simtec.co.uk/
- *
- * S3C24A0 - timer tick support
- */
-
-#define SUBSRC_TIMER4 (1 << (IRQ_TIMER4 - IRQ_S3CUART_RX0))
-
-static inline int s3c24xx_ostimer_pending(void)
-{
- return __raw_readl(S3C2410_SUBSRCPND) & SUBSRC_TIMER4;
-}
+++ /dev/null
-/* linux/arch/arm/mach-s3c24a0/include/mach/timex.h
- *
- * Copyright (c) 2008 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * S3C2410 - time parameters
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-#define CLOCK_TICK_RATE 12000000
-
-#endif /* __ASM_ARCH_TIMEX_H */
+++ /dev/null
-/* linux/include/asm-arm/arch-s3c24ao/vmalloc.h
- *
- * Copyright 2008 Simtec Electronics <linux@simtec.co.uk>
-
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * S3C24A0 vmalloc definition
-*/
-
-#ifndef __ASM_ARCH_VMALLOC_H
-#define __ASM_ARCH_VMALLOC_H
-
-#define VMALLOC_END 0xF6000000UL
-
-#endif /* __ASM_ARCH_VMALLOC_H */
config PLAT_S3C24XX
bool
- depends on ARCH_S3C2410 || ARCH_S3C24A0
+ depends on ARCH_S3C2410
default y
select NO_IOPORT
select ARCH_REQUIRE_GPIOLIB
#include <plat/cpu.h>
#include <plat/devs.h>
#include <plat/clock.h>
-#include <plat/s3c2400.h>
#include <plat/s3c2410.h>
#include <plat/s3c2412.h>
#include <plat/s3c2416.h>
/* table of supported CPUs */
-static const char name_s3c2400[] = "S3C2400";
static const char name_s3c2410[] = "S3C2410";
static const char name_s3c2412[] = "S3C2412";
static const char name_s3c2416[] = "S3C2416/S3C2450";
.init = s3c2443_init,
.name = name_s3c2443,
},
- {
- .idcode = 0x0, /* S3C2400 doesn't have an idcode */
- .idmask = 0xffffffff,
- .map_io = s3c2400_map_io,
- .init_clocks = s3c2400_init_clocks,
- .init_uarts = s3c2400_init_uarts,
- .init = s3c2400_init,
- .name = name_s3c2400
- },
};
/* minimal IO mapping */
static unsigned long s3c24xx_read_idcode_v4(void)
{
-#ifndef CONFIG_CPU_S3C2400
return __raw_readl(S3C2410_GSTATUS1);
-#else
- return 0UL;
-#endif
}
/* Hook for arm_pm_restart to ensure we execute the reset code
#define S3C2410_IISFCON_RXMASK (0x3f)
#define S3C2410_IISFCON_RXSHIFT (0)
-#define S3C2400_IISFCON_TXDMA (1<<11)
-#define S3C2400_IISFCON_RXDMA (1<<10)
-#define S3C2400_IISFCON_TXENABLE (1<<9)
-#define S3C2400_IISFCON_RXENABLE (1<<8)
-#define S3C2400_IISFCON_TXMASK (0x07 << 4)
-#define S3C2400_IISFCON_TXSHIFT (4)
-#define S3C2400_IISFCON_RXMASK (0x07)
-#define S3C2400_IISFCON_RXSHIFT (0)
-
#define S3C2410_IISFIFO (0x10)
#endif /* __ASM_ARCH_REGS_IIS_H */
#define S3C2410_SPPIN_ENMUL (1<<2) /* Multi Master Error detect */
#define S3C2410_SPPIN_RESERVED (1<<1)
-#define S3C2400_SPPIN_nCS (1<<1) /* SPI Card Select */
#define S3C2410_SPPIN_KEEP (1<<0) /* Master Out keep */
#define S3C2410_SPPRE (0x0C)
+++ /dev/null
-/* linux/include/asm-arm/plat-s3c24xx/s3c2400.h
- *
- * Copyright (c) 2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
- *
- * Header file for S3C2400 cpu support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * Modifications:
- * 09-Fev-2006 LCVR First version, based on s3c2410.h
-*/
-
-#ifdef CONFIG_CPU_S3C2400
-
-extern int s3c2400_init(void);
-
-extern void s3c2400_map_io(void);
-
-extern void s3c2400_init_uarts(struct s3c2410_uartcfg *cfg, int no);
-
-extern void s3c2400_init_clocks(int xtal);
-
-#else
-#define s3c2400_init_clocks NULL
-#define s3c2400_init_uarts NULL
-#define s3c2400_map_io NULL
-#define s3c2400_init NULL
-#endif
/* Pull-{up,down} resistor controls.
*
- * S3C2410,S3C2440,S3C24A0 = Pull-UP,
+ * S3C2410,S3C2440 = Pull-UP,
* S3C2412,S3C2413 = Pull-Down
* S3C6400,S3C6410 = Pull-Both [None,Down,Up,Undef]
* S3C2443 = Pull-Both [not same as S3C6400]
#define S3C2410_UFSTAT_RXMASK (15<<0)
#define S3C2410_UFSTAT_RXSHIFT (0)
-/* UFSTAT S3C24A0 */
-#define S3C24A0_UFSTAT_TXFULL (1 << 14)
-#define S3C24A0_UFSTAT_RXFULL (1 << 6)
-#define S3C24A0_UFSTAT_TXMASK (63 << 8)
-#define S3C24A0_UFSTAT_TXSHIFT (8)
-#define S3C24A0_UFSTAT_RXMASK (63)
-#define S3C24A0_UFSTAT_RXSHIFT (0)
-
/* UFSTAT S3C2443 same as S3C2440 */
#define S3C2440_UFSTAT_TXFULL (1<<14)
#define S3C2440_UFSTAT_RXFULL (1<<6)
config SERIAL_SAMSUNG_UARTS
int
depends on ARM && PLAT_SAMSUNG
- default 2 if ARCH_S3C2400
default 6 if ARCH_S5P6450
default 4 if SERIAL_SAMSUNG_UARTS_4
default 3
your boot loader about how to pass options to the kernel at
boot time.)
-config SERIAL_S3C2400
- tristate "Samsung S3C2410 Serial port support"
- depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400
- default y if CPU_S3C2400
- help
- Serial port support for the Samsung S3C2400 SoC
-
config SERIAL_S3C2410
tristate "Samsung S3C2410 Serial port support"
depends on SERIAL_SAMSUNG && CPU_S3C2410
help
Serial port support for the Samsung S3C2440, S3C2416 and S3C2442 SoC
-config SERIAL_S3C24A0
- tristate "Samsung S3C24A0 Serial port support"
- depends on SERIAL_SAMSUNG && CPU_S3C24A0
- default y if CPU_S3C24A0
- help
- Serial port support for the Samsung S3C24A0 SoC
-
config SERIAL_S3C6400
tristate "Samsung S3C6400/S3C6410/S5P6440/S5P6450/S5PC100 Serial port support"
depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410 || CPU_S5P6440 || CPU_S5P6450 || CPU_S5PC100)
obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
-obj-$(CONFIG_SERIAL_S3C2400) += s3c2400.o
obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o
obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o
-obj-$(CONFIG_SERIAL_S3C24A0) += s3c24a0.o
obj-$(CONFIG_SERIAL_S3C6400) += s3c6400.o
obj-$(CONFIG_SERIAL_S5PV210) += s5pv210.o
obj-$(CONFIG_SERIAL_MAX3100) += max3100.o
+++ /dev/null
-/*
- * Driver for Samsung SoC onboard UARTs.
- *
- * Ben Dooks, Copyright (c) 2003-2005 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-
-#include <asm/irq.h>
-
-#include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
-#include <mach/regs-gpio.h>
-
-#include "samsung.h"
-
-static int s3c2400_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- clk->divisor = 1;
- clk->name = "pclk";
-
- return 0;
-}
-
-static int s3c2400_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- return 0;
-}
-
-static int s3c2400_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- dbg("s3c2400_serial_resetport: port=%p (%08lx), cfg=%p\n",
- port, port->mapbase, cfg);
-
- wr_regl(port, S3C2410_UCON, cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c2400_uart_inf = {
- .name = "Samsung S3C2400 UART",
- .type = PORT_S3C2400,
- .fifosize = 16,
- .rx_fifomask = S3C2410_UFSTAT_RXMASK,
- .rx_fifoshift = S3C2410_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C2410_UFSTAT_RXFULL,
- .tx_fifofull = S3C2410_UFSTAT_TXFULL,
- .tx_fifomask = S3C2410_UFSTAT_TXMASK,
- .tx_fifoshift = S3C2410_UFSTAT_TXSHIFT,
- .get_clksrc = s3c2400_serial_getsource,
- .set_clksrc = s3c2400_serial_setsource,
- .reset_port = s3c2400_serial_resetport,
-};
-
-static int s3c2400_serial_probe(struct platform_device *dev)
-{
- return s3c24xx_serial_probe(dev, &s3c2400_uart_inf);
-}
-
-static struct platform_driver s3c2400_serial_driver = {
- .probe = s3c2400_serial_probe,
- .remove = __devexit_p(s3c24xx_serial_remove),
- .driver = {
- .name = "s3c2400-uart",
- .owner = THIS_MODULE,
- },
-};
-
-s3c24xx_console_init(&s3c2400_serial_driver, &s3c2400_uart_inf);
-
-static inline int s3c2400_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c2400_serial_driver, &s3c2400_uart_inf);
-}
-
-static inline void s3c2400_serial_exit(void)
-{
- platform_driver_unregister(&s3c2400_serial_driver);
-}
-
-module_init(s3c2400_serial_init);
-module_exit(s3c2400_serial_exit);
-
-MODULE_LICENSE("GPL v2");
-MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_DESCRIPTION("Samsung S3C2400 SoC Serial port driver");
-MODULE_ALIAS("platform:s3c2400-uart");
+++ /dev/null
-/*
- * Driver for Samsung S3C24A0 SoC onboard UARTs.
- *
- * Based on drivers/serial/s3c2410.c
- *
- * Author: Sandeep Patil <sandeep.patil@azingo.com>
- *
- * Ben Dooks, Copyright (c) 2003-2008 Simtec Electronics
- * http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-
-#include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
-#include <mach/regs-gpio.h>
-
-#include "samsung.h"
-
-static int s3c24a0_serial_setsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- if (strcmp(clk->name, "uclk") == 0)
- ucon |= S3C2410_UCON_UCLK;
- else
- ucon &= ~S3C2410_UCON_UCLK;
-
- wr_regl(port, S3C2410_UCON, ucon);
- return 0;
-}
-
-static int s3c24a0_serial_getsource(struct uart_port *port,
- struct s3c24xx_uart_clksrc *clk)
-{
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
- clk->divisor = 1;
- clk->name = (ucon & S3C2410_UCON_UCLK) ? "uclk" : "pclk";
-
- return 0;
-}
-
-static int s3c24a0_serial_resetport(struct uart_port *port,
- struct s3c2410_uartcfg *cfg)
-{
- dbg("s3c24a0_serial_resetport: port=%p (%08lx), cfg=%p\n",
- port, port->mapbase, cfg);
-
- wr_regl(port, S3C2410_UCON, cfg->ucon);
- wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
- /* reset both fifos */
-
- wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
- wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
- return 0;
-}
-
-static struct s3c24xx_uart_info s3c24a0_uart_inf = {
- .name = "Samsung S3C24A0 UART",
- .type = PORT_S3C2410,
- .fifosize = 16,
- .rx_fifomask = S3C24A0_UFSTAT_RXMASK,
- .rx_fifoshift = S3C24A0_UFSTAT_RXSHIFT,
- .rx_fifofull = S3C24A0_UFSTAT_RXFULL,
- .tx_fifofull = S3C24A0_UFSTAT_TXFULL,
- .tx_fifomask = S3C24A0_UFSTAT_TXMASK,
- .tx_fifoshift = S3C24A0_UFSTAT_TXSHIFT,
- .get_clksrc = s3c24a0_serial_getsource,
- .set_clksrc = s3c24a0_serial_setsource,
- .reset_port = s3c24a0_serial_resetport,
-};
-
-static int s3c24a0_serial_probe(struct platform_device *dev)
-{
- return s3c24xx_serial_probe(dev, &s3c24a0_uart_inf);
-}
-
-static struct platform_driver s3c24a0_serial_driver = {
- .probe = s3c24a0_serial_probe,
- .remove = __devexit_p(s3c24xx_serial_remove),
- .driver = {
- .name = "s3c24a0-uart",
- .owner = THIS_MODULE,
- },
-};
-
-s3c24xx_console_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf);
-
-static int __init s3c24a0_serial_init(void)
-{
- return s3c24xx_serial_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf);
-}
-
-static void __exit s3c24a0_serial_exit(void)
-{
- platform_driver_unregister(&s3c24a0_serial_driver);
-}
-
-module_init(s3c24a0_serial_init);
-module_exit(s3c24a0_serial_exit);
-
projects / cascardo / linux.git / commitdiff