CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MPC=y
CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_GE_FPGA=y
CONFIG_SENSORS_LM90=y
CONFIG_SENSORS_LM92=y
CONFIG_WATCHDOG=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MPC=y
CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_GE_FPGA=y
CONFIG_SENSORS_LM90=y
CONFIG_SENSORS_LM92=y
CONFIG_WATCHDOG=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MPC=y
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_GE_FPGA=y
CONFIG_SENSORS_LM90=y
CONFIG_SENSORS_LM92=y
CONFIG_WATCHDOG=y
obj-$(CONFIG_MPC8641_HPCN) += mpc86xx_hpcn.o
obj-$(CONFIG_SBC8641D) += sbc8641d.o
obj-$(CONFIG_MPC8610_HPCD) += mpc8610_hpcd.o
-gef-gpio-$(CONFIG_GPIOLIB) += gef_gpio.o
-obj-$(CONFIG_GE_FPGA) += gef_pic.o $(gef-gpio-y)
+obj-$(CONFIG_GE_FPGA) += gef_pic.o
obj-$(CONFIG_GEF_SBC610) += gef_sbc610.o
obj-$(CONFIG_GEF_SBC310) += gef_sbc310.o
obj-$(CONFIG_GEF_PPC9A) += gef_ppc9a.o
+++ /dev/null
-/*
- * Driver for GE FPGA based GPIO
- *
- * Author: Martyn Welch <martyn.welch@ge.com>
- *
- * 2008 (c) GE Intelligent Platforms Embedded Systems, Inc.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-/* TODO
- *
- * Configuration of output modes (totem-pole/open-drain)
- * Interrupt configuration - interrupts are always generated the FPGA relies on
- * the I/O interrupt controllers mask to stop them propergating
- */
-
-#include <linux/kernel.h>
-#include <linux/compiler.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/of_platform.h>
-#include <linux/of_gpio.h>
-#include <linux/gpio.h>
-#include <linux/slab.h>
-#include <linux/module.h>
-
-#define GEF_GPIO_DIRECT 0x00
-#define GEF_GPIO_IN 0x04
-#define GEF_GPIO_OUT 0x08
-#define GEF_GPIO_TRIG 0x0C
-#define GEF_GPIO_POLAR_A 0x10
-#define GEF_GPIO_POLAR_B 0x14
-#define GEF_GPIO_INT_STAT 0x18
-#define GEF_GPIO_OVERRUN 0x1C
-#define GEF_GPIO_MODE 0x20
-
-static void _gef_gpio_set(void __iomem *reg, unsigned int offset, int value)
-{
- unsigned int data;
-
- data = ioread32be(reg);
- /* value: 0=low; 1=high */
- if (value & 0x1)
- data = data | (0x1 << offset);
- else
- data = data & ~(0x1 << offset);
-
- iowrite32be(data, reg);
-}
-
-
-static int gef_gpio_dir_in(struct gpio_chip *chip, unsigned offset)
-{
- unsigned int data;
- struct of_mm_gpio_chip *mmchip = to_of_mm_gpio_chip(chip);
-
- data = ioread32be(mmchip->regs + GEF_GPIO_DIRECT);
- data = data | (0x1 << offset);
- iowrite32be(data, mmchip->regs + GEF_GPIO_DIRECT);
-
- return 0;
-}
-
-static int gef_gpio_dir_out(struct gpio_chip *chip, unsigned offset, int value)
-{
- unsigned int data;
- struct of_mm_gpio_chip *mmchip = to_of_mm_gpio_chip(chip);
-
- /* Set direction before switching to input */
- _gef_gpio_set(mmchip->regs + GEF_GPIO_OUT, offset, value);
-
- data = ioread32be(mmchip->regs + GEF_GPIO_DIRECT);
- data = data & ~(0x1 << offset);
- iowrite32be(data, mmchip->regs + GEF_GPIO_DIRECT);
-
- return 0;
-}
-
-static int gef_gpio_get(struct gpio_chip *chip, unsigned offset)
-{
- unsigned int data;
- int state = 0;
- struct of_mm_gpio_chip *mmchip = to_of_mm_gpio_chip(chip);
-
- data = ioread32be(mmchip->regs + GEF_GPIO_IN);
- state = (int)((data >> offset) & 0x1);
-
- return state;
-}
-
-static void gef_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
-{
- struct of_mm_gpio_chip *mmchip = to_of_mm_gpio_chip(chip);
-
- _gef_gpio_set(mmchip->regs + GEF_GPIO_OUT, offset, value);
-}
-
-static int __init gef_gpio_init(void)
-{
- struct device_node *np;
- int retval;
- struct of_mm_gpio_chip *gef_gpio_chip;
-
- for_each_compatible_node(np, NULL, "gef,sbc610-gpio") {
-
- pr_debug("%s: Initialising GEF GPIO\n", np->full_name);
-
- /* Allocate chip structure */
- gef_gpio_chip = kzalloc(sizeof(*gef_gpio_chip), GFP_KERNEL);
- if (!gef_gpio_chip) {
- pr_err("%s: Unable to allocate structure\n",
- np->full_name);
- continue;
- }
-
- /* Setup pointers to chip functions */
- gef_gpio_chip->gc.of_gpio_n_cells = 2;
- gef_gpio_chip->gc.ngpio = 19;
- gef_gpio_chip->gc.direction_input = gef_gpio_dir_in;
- gef_gpio_chip->gc.direction_output = gef_gpio_dir_out;
- gef_gpio_chip->gc.get = gef_gpio_get;
- gef_gpio_chip->gc.set = gef_gpio_set;
-
- /* This function adds a memory mapped GPIO chip */
- retval = of_mm_gpiochip_add(np, gef_gpio_chip);
- if (retval) {
- kfree(gef_gpio_chip);
- pr_err("%s: Unable to add GPIO\n", np->full_name);
- }
- }
-
- for_each_compatible_node(np, NULL, "gef,sbc310-gpio") {
-
- pr_debug("%s: Initialising GEF GPIO\n", np->full_name);
-
- /* Allocate chip structure */
- gef_gpio_chip = kzalloc(sizeof(*gef_gpio_chip), GFP_KERNEL);
- if (!gef_gpio_chip) {
- pr_err("%s: Unable to allocate structure\n",
- np->full_name);
- continue;
- }
-
- /* Setup pointers to chip functions */
- gef_gpio_chip->gc.of_gpio_n_cells = 2;
- gef_gpio_chip->gc.ngpio = 6;
- gef_gpio_chip->gc.direction_input = gef_gpio_dir_in;
- gef_gpio_chip->gc.direction_output = gef_gpio_dir_out;
- gef_gpio_chip->gc.get = gef_gpio_get;
- gef_gpio_chip->gc.set = gef_gpio_set;
-
- /* This function adds a memory mapped GPIO chip */
- retval = of_mm_gpiochip_add(np, gef_gpio_chip);
- if (retval) {
- kfree(gef_gpio_chip);
- pr_err("%s: Unable to add GPIO\n", np->full_name);
- }
- }
-
- return 0;
-};
-arch_initcall(gef_gpio_init);
-
-MODULE_DESCRIPTION("GE I/O FPGA GPIO driver");
-MODULE_AUTHOR("Martyn Welch <martyn.welch@ge.com");
-MODULE_LICENSE("GPL");
additional drivers must be enabled in order to use the
functionality of the device.
+config GPIO_GE_FPGA
+ bool "GE FPGA based GPIO"
+ depends on GE_FPGA
+ help
+ Support for common GPIO functionality provided on some GE Single Board
+ Computers.
+
+ This driver provides basic support (configure as input or output, read
+ and write pin state) for GPIO implemented in a number of GE single
+ board computers.
+
comment "I2C GPIO expanders:"
config GPIO_MAX7300
obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
obj-$(CONFIG_ARCH_DAVINCI) += gpio-davinci.o
obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o
+obj-$(CONFIG_GPIO_GE_FPGA) += gpio-ge.o
obj-$(CONFIG_GPIO_IT8761E) += gpio-it8761e.o
obj-$(CONFIG_GPIO_JANZ_TTL) += gpio-janz-ttl.o
obj-$(CONFIG_ARCH_KS8695) += gpio-ks8695.o
--- /dev/null
+/*
+ * Driver for GE FPGA based GPIO
+ *
+ * Author: Martyn Welch <martyn.welch@ge.com>
+ *
+ * 2008 (c) GE Intelligent Platforms Embedded Systems, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/* TODO
+ *
+ * Configuration of output modes (totem-pole/open-drain)
+ * Interrupt configuration - interrupts are always generated the FPGA relies on
+ * the I/O interrupt controllers mask to stop them propergating
+ */
+
+#include <linux/kernel.h>
+#include <linux/compiler.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/of_gpio.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+
+#define GEF_GPIO_DIRECT 0x00
+#define GEF_GPIO_IN 0x04
+#define GEF_GPIO_OUT 0x08
+#define GEF_GPIO_TRIG 0x0C
+#define GEF_GPIO_POLAR_A 0x10
+#define GEF_GPIO_POLAR_B 0x14
+#define GEF_GPIO_INT_STAT 0x18
+#define GEF_GPIO_OVERRUN 0x1C
+#define GEF_GPIO_MODE 0x20
+
+static void _gef_gpio_set(void __iomem *reg, unsigned int offset, int value)
+{
+ unsigned int data;
+
+ data = ioread32be(reg);
+ /* value: 0=low; 1=high */
+ if (value & 0x1)
+ data = data | (0x1 << offset);
+ else
+ data = data & ~(0x1 << offset);
+
+ iowrite32be(data, reg);
+}
+
+
+static int gef_gpio_dir_in(struct gpio_chip *chip, unsigned offset)
+{
+ unsigned int data;
+ struct of_mm_gpio_chip *mmchip = to_of_mm_gpio_chip(chip);
+
+ data = ioread32be(mmchip->regs + GEF_GPIO_DIRECT);
+ data = data | (0x1 << offset);
+ iowrite32be(data, mmchip->regs + GEF_GPIO_DIRECT);
+
+ return 0;
+}
+
+static int gef_gpio_dir_out(struct gpio_chip *chip, unsigned offset, int value)
+{
+ unsigned int data;
+ struct of_mm_gpio_chip *mmchip = to_of_mm_gpio_chip(chip);
+
+ /* Set direction before switching to input */
+ _gef_gpio_set(mmchip->regs + GEF_GPIO_OUT, offset, value);
+
+ data = ioread32be(mmchip->regs + GEF_GPIO_DIRECT);
+ data = data & ~(0x1 << offset);
+ iowrite32be(data, mmchip->regs + GEF_GPIO_DIRECT);
+
+ return 0;
+}
+
+static int gef_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ unsigned int data;
+ int state = 0;
+ struct of_mm_gpio_chip *mmchip = to_of_mm_gpio_chip(chip);
+
+ data = ioread32be(mmchip->regs + GEF_GPIO_IN);
+ state = (int)((data >> offset) & 0x1);
+
+ return state;
+}
+
+static void gef_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct of_mm_gpio_chip *mmchip = to_of_mm_gpio_chip(chip);
+
+ _gef_gpio_set(mmchip->regs + GEF_GPIO_OUT, offset, value);
+}
+
+static int __init gef_gpio_init(void)
+{
+ struct device_node *np;
+ int retval;
+ struct of_mm_gpio_chip *gef_gpio_chip;
+
+ for_each_compatible_node(np, NULL, "gef,sbc610-gpio") {
+
+ pr_debug("%s: Initialising GEF GPIO\n", np->full_name);
+
+ /* Allocate chip structure */
+ gef_gpio_chip = kzalloc(sizeof(*gef_gpio_chip), GFP_KERNEL);
+ if (!gef_gpio_chip) {
+ pr_err("%s: Unable to allocate structure\n",
+ np->full_name);
+ continue;
+ }
+
+ /* Setup pointers to chip functions */
+ gef_gpio_chip->gc.of_gpio_n_cells = 2;
+ gef_gpio_chip->gc.ngpio = 19;
+ gef_gpio_chip->gc.direction_input = gef_gpio_dir_in;
+ gef_gpio_chip->gc.direction_output = gef_gpio_dir_out;
+ gef_gpio_chip->gc.get = gef_gpio_get;
+ gef_gpio_chip->gc.set = gef_gpio_set;
+
+ /* This function adds a memory mapped GPIO chip */
+ retval = of_mm_gpiochip_add(np, gef_gpio_chip);
+ if (retval) {
+ kfree(gef_gpio_chip);
+ pr_err("%s: Unable to add GPIO\n", np->full_name);
+ }
+ }
+
+ for_each_compatible_node(np, NULL, "gef,sbc310-gpio") {
+
+ pr_debug("%s: Initialising GEF GPIO\n", np->full_name);
+
+ /* Allocate chip structure */
+ gef_gpio_chip = kzalloc(sizeof(*gef_gpio_chip), GFP_KERNEL);
+ if (!gef_gpio_chip) {
+ pr_err("%s: Unable to allocate structure\n",
+ np->full_name);
+ continue;
+ }
+
+ /* Setup pointers to chip functions */
+ gef_gpio_chip->gc.of_gpio_n_cells = 2;
+ gef_gpio_chip->gc.ngpio = 6;
+ gef_gpio_chip->gc.direction_input = gef_gpio_dir_in;
+ gef_gpio_chip->gc.direction_output = gef_gpio_dir_out;
+ gef_gpio_chip->gc.get = gef_gpio_get;
+ gef_gpio_chip->gc.set = gef_gpio_set;
+
+ /* This function adds a memory mapped GPIO chip */
+ retval = of_mm_gpiochip_add(np, gef_gpio_chip);
+ if (retval) {
+ kfree(gef_gpio_chip);
+ pr_err("%s: Unable to add GPIO\n", np->full_name);
+ }
+ }
+
+ return 0;
+};
+arch_initcall(gef_gpio_init);
+
+MODULE_DESCRIPTION("GE I/O FPGA GPIO driver");
+MODULE_AUTHOR("Martyn Welch <martyn.welch@ge.com");
+MODULE_LICENSE("GPL");
projects / cascardo / linux.git / commitdiff