ARM: msm: Update the references to DEBUG_MSM_UARTx

The Kconfig options DEBUG_MSM_UART1, DEBUG_MSM_UART2, DEBUG_MSM_UART3,
MSM_DEBUG_UART1, MSM_DEBUG_UART2 and MSM_DEBUG_UART3 are removed, but
they are still referenced in the following files:
	arch/arm/mach-msm/io.c,
	arch/arm/mach-msm/board-trout.c
	arch/arm/mach-msm/board-trout-gpio.c

Fix this by updating the reference to the new Kconfig option.

Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

diff --git a/arch/arm/mach-msm/board-trout-gpio.c b/arch/arm/mach-msm/board-trout-gpio.c
index 2c25050..722ad63 100644 (file)
--- a/arch/arm/mach-msm/board-trout-gpio.c
+++ b/arch/arm/mach-msm/board-trout-gpio.c
@@ -94,7 +94,7 @@ static int trout_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
        }
 
 static struct msm_gpio_chip msm_gpio_banks[] = {
-#if defined(CONFIG_MSM_DEBUG_UART1)
+#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9a00000)
        /* H2W pins <-> UART1 */
        TROUT_GPIO_BANK("MISC2", 0x00,   TROUT_GPIO_MISC2_BASE, 0x40),
 #else

diff --git a/arch/arm/mach-msm/board-trout.c b/arch/arm/mach-msm/board-trout.c
index f72b07d..ba3edd3 100644 (file)
--- a/arch/arm/mach-msm/board-trout.c
+++ b/arch/arm/mach-msm/board-trout.c
@@ -88,7 +88,7 @@ static void __init trout_map_io(void)
        msm_map_common_io();
        iotable_init(trout_io_desc, ARRAY_SIZE(trout_io_desc));
 
-#ifdef CONFIG_MSM_DEBUG_UART3
+#if defined(CONFIG_DEBUG_MSM_UART) && (CONFIG_DEBUG_UART_PHYS == 0xa9c00000)
        /* route UART3 to the "H2W" extended usb connector */
        writeb(0x80, TROUT_CPLD_BASE + 0x00);
 #endif

diff --git a/arch/arm/mach-msm/io.c b/arch/arm/mach-msm/io.c
index 34e0947..b042dca 100644 (file)
--- a/arch/arm/mach-msm/io.c
+++ b/arch/arm/mach-msm/io.c
@@ -57,8 +57,7 @@ static struct map_desc msm_io_desc[] __initdata = {
                .length =   MSM_SHARED_RAM_SIZE,
                .type =     MT_DEVICE,
        },
-#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
-               defined(CONFIG_DEBUG_MSM_UART3)
+#if defined(CONFIG_DEBUG_MSM_UART)
        {
                /* Must be last: virtual and pfn filled in by debug_ll_addr() */
                .length = SZ_4K,
@@ -76,8 +75,7 @@ void __init msm_map_common_io(void)
         * pages are peripheral interface or not.
         */
        asm("mcr p15, 0, %0, c15, c2, 4" : : "r" (0));
-#if defined(CONFIG_DEBUG_MSM_UART1) || defined(CONFIG_DEBUG_MSM_UART2) || \
-               defined(CONFIG_DEBUG_MSM_UART3)
+#if defined(CONFIG_DEBUG_MSM_UART)
 #ifdef CONFIG_MMU
        debug_ll_addr(&msm_io_desc[size - 1].pfn,
                      &msm_io_desc[size - 1].virtual);