W: http://www.polyware.nl/~middelin/hobbies.html
S: Maintained
+ZS DECSTATION Z85C30 SERIAL DRIVER
+P: Maciej W. Rozycki
+M: macro@linux-mips.org
+S: Maintained
+
THE REST
P: Linus Torvalds
S: Buried alive in reporters
To compile this driver as a module, choose M here: the
module will be called istallion.
-config SERIAL_DEC
- bool "DECstation serial support"
- depends on MACH_DECSTATION
- default y
- help
- This selects whether you want to be asked about drivers for
- DECstation serial ports.
-
- Note that the answer to this question won't directly affect the
- kernel: saying N will just cause the configurator to skip all
- the questions about DECstation serial ports.
-
-config SERIAL_DEC_CONSOLE
- bool "Support for console on a DECstation serial port"
- depends on SERIAL_DEC
- default y
- help
- If you say Y here, it will be possible to use a serial port as the
- system console (the system console is the device which receives all
- kernel messages and warnings and which allows logins in single user
- mode). Note that the firmware uses ttyS0 as the serial console on
- the Maxine and ttyS2 on the others.
-
- If unsure, say Y.
-
-config ZS
- bool "Z85C30 Serial Support"
- depends on SERIAL_DEC
- default y
- help
- Documentation on the Zilog 85C350 serial communications controller
- is downloadable at <http://www.zilog.com/pdfs/serial/z85c30.pdf>
-
config A2232
tristate "Commodore A2232 serial support (EXPERIMENTAL)"
depends on EXPERIMENTAL && ZORRO && BROKEN_ON_SMP
+++ /dev/null
-/*
- * sercons.c
- * choose the right serial device at boot time
- *
- * triemer 6-SEP-1998
- * sercons.c is designed to allow the three different kinds
- * of serial devices under the decstation world to co-exist
- * in the same kernel. The idea here is to abstract
- * the pieces of the drivers that are common to this file
- * so that they do not clash at compile time and runtime.
- *
- * HK 16-SEP-1998 v0.002
- * removed the PROM console as this is not a real serial
- * device. Added support for PROM console in drivers/char/tty_io.c
- * instead. Although it may work to enable more than one
- * console device I strongly recommend to use only one.
- */
-
-#include <linux/init.h>
-#include <asm/dec/machtype.h>
-
-#ifdef CONFIG_ZS
-extern int zs_init(void);
-#endif
-
-#ifdef CONFIG_SERIAL_CONSOLE
-
-#ifdef CONFIG_ZS
-extern void zs_serial_console_init(void);
-#endif
-
-#endif
-
-/* rs_init - starts up the serial interface -
- handle normal case of starting up the serial interface */
-
-#ifdef CONFIG_SERIAL
-
-int __init rs_init(void)
-{
-#ifdef CONFIG_ZS
- if (IOASIC)
- return zs_init();
-#endif
- return -ENXIO;
-}
-
-__initcall(rs_init);
-
-#endif
-
-#ifdef CONFIG_SERIAL_CONSOLE
-
-/* serial_console_init handles the special case of starting
- * up the console on the serial port
- */
-static int __init decserial_console_init(void)
-{
-#ifdef CONFIG_ZS
- if (IOASIC)
- zs_serial_console_init();
-#endif
- return 0;
-}
-console_initcall(decserial_console_init);
-
-#endif
If unsure, say Y.
+config SERIAL_ZS
+ tristate "DECstation Z85C30 serial support"
+ depends on MACH_DECSTATION
+ select SERIAL_CORE
+ default y
+ ---help---
+ Support for the Zilog 85C350 serial communications controller used
+ for serial ports in newer DECstation systems. These include the
+ DECsystem 5900 and all models of the DECstation and DECsystem 5000
+ systems except from model 200.
+
+ If unsure, say Y. To compile this driver as a module, choose M here:
+ the module will be called zs.
+
+config SERIAL_ZS_CONSOLE
+ bool "Support for console on a DECstation Z85C30 serial port"
+ depends on SERIAL_ZS=y
+ select SERIAL_CORE_CONSOLE
+ default y
+ ---help---
+ If you say Y here, it will be possible to use a serial port as the
+ system console (the system console is the device which receives all
+ kernel messages and warnings and which allows logins in single user
+ mode).
+
+ Note that the firmware uses ttyS1 as the serial console on the
+ Maxine and ttyS3 on the others using this driver.
+
+ If unsure, say Y.
+
config SERIAL_21285
tristate "DC21285 serial port support"
depends on ARM && FOOTBRIDGE
obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o
obj-$(CONFIG_SERIAL_LH7A40X) += serial_lh7a40x.o
obj-$(CONFIG_SERIAL_DZ) += dz.o
+obj-$(CONFIG_SERIAL_ZS) += zs.o
obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o
obj-$(CONFIG_SERIAL_SGI_L1_CONSOLE) += sn_console.o
obj-$(CONFIG_SERIAL_CPM) += cpm_uart/
--- /dev/null
+/*
+ * zs.c: Serial port driver for IOASIC DECstations.
+ *
+ * Derived from drivers/sbus/char/sunserial.c by Paul Mackerras.
+ * Derived from drivers/macintosh/macserial.c by Harald Koerfgen.
+ *
+ * DECstation changes
+ * Copyright (C) 1998-2000 Harald Koerfgen
+ * Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2007 Maciej W. Rozycki
+ *
+ * For the rest of the code the original Copyright applies:
+ * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ *
+ *
+ * Note: for IOASIC systems the wiring is as follows:
+ *
+ * mouse/keyboard:
+ * DIN-7 MJ-4 signal SCC
+ * 2 1 TxD <- A.TxD
+ * 3 4 RxD -> A.RxD
+ *
+ * EIA-232/EIA-423:
+ * DB-25 MMJ-6 signal SCC
+ * 2 2 TxD <- B.TxD
+ * 3 5 RxD -> B.RxD
+ * 4 RTS <- ~A.RTS
+ * 5 CTS -> ~B.CTS
+ * 6 6 DSR -> ~A.SYNC
+ * 8 CD -> ~B.DCD
+ * 12 DSRS(DCE) -> ~A.CTS (*)
+ * 15 TxC -> B.TxC
+ * 17 RxC -> B.RxC
+ * 20 1 DTR <- ~A.DTR
+ * 22 RI -> ~A.DCD
+ * 23 DSRS(DTE) <- ~B.RTS
+ *
+ * (*) EIA-232 defines the signal at this pin to be SCD, while DSRS(DCE)
+ * is shared with DSRS(DTE) at pin 23.
+ *
+ * As you can immediately notice the wiring of the RTS, DTR and DSR signals
+ * is a bit odd. This makes the handling of port B unnecessarily
+ * complicated and prevents the use of some automatic modes of operation.
+ */
+
+#if defined(CONFIG_SERIAL_ZS_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/bug.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/irqflags.h>
+#include <linux/kernel.h>
+#include <linux/major.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/spinlock.h>
+#include <linux/sysrq.h>
+#include <linux/tty.h>
+#include <linux/types.h>
+
+#include <asm/atomic.h>
+#include <asm/system.h>
+
+#include <asm/dec/interrupts.h>
+#include <asm/dec/ioasic_addrs.h>
+#include <asm/dec/system.h>
+
+#include "zs.h"
+
+
+MODULE_AUTHOR("Maciej W. Rozycki <macro@linux-mips.org>");
+MODULE_DESCRIPTION("DECstation Z85C30 serial driver");
+MODULE_LICENSE("GPL");
+
+
+static char zs_name[] __initdata = "DECstation Z85C30 serial driver version ";
+static char zs_version[] __initdata = "0.10";
+
+/*
+ * It would be nice to dynamically allocate everything that
+ * depends on ZS_NUM_SCCS, so we could support any number of
+ * Z85C30s, but for now...
+ */
+#define ZS_NUM_SCCS 2 /* Max # of ZS chips supported. */
+#define ZS_NUM_CHAN 2 /* 2 channels per chip. */
+#define ZS_CHAN_A 0 /* Index of the channel A. */
+#define ZS_CHAN_B 1 /* Index of the channel B. */
+#define ZS_CHAN_IO_SIZE 8 /* IOMEM space size. */
+#define ZS_CHAN_IO_STRIDE 4 /* Register alignment. */
+#define ZS_CHAN_IO_OFFSET 1 /* The SCC resides on the high byte
+ of the 16-bit IOBUS. */
+#define ZS_CLOCK 7372800 /* Z85C30 PCLK input clock rate. */
+
+#define to_zport(uport) container_of(uport, struct zs_port, port)
+
+struct zs_parms {
+ resource_size_t scc[ZS_NUM_SCCS];
+ int irq[ZS_NUM_SCCS];
+};
+
+static struct zs_scc zs_sccs[ZS_NUM_SCCS];
+
+static u8 zs_init_regs[ZS_NUM_REGS] __initdata = {
+ 0, /* write 0 */
+ PAR_SPEC, /* write 1 */
+ 0, /* write 2 */
+ 0, /* write 3 */
+ X16CLK | SB1, /* write 4 */
+ 0, /* write 5 */
+ 0, 0, 0, /* write 6, 7, 8 */
+ MIE | DLC | NV, /* write 9 */
+ NRZ, /* write 10 */
+ TCBR | RCBR, /* write 11 */
+ 0, 0, /* BRG time constant, write 12 + 13 */
+ BRSRC | BRENABL, /* write 14 */
+ 0, /* write 15 */
+};
+
+/*
+ * Debugging.
+ */
+#undef ZS_DEBUG_REGS
+
+
+/*
+ * Reading and writing Z85C30 registers.
+ */
+static void recovery_delay(void)
+{
+ udelay(2);
+}
+
+static u8 read_zsreg(struct zs_port *zport, int reg)
+{
+ void __iomem *control = zport->port.membase + ZS_CHAN_IO_OFFSET;
+ u8 retval;
+
+ if (reg != 0) {
+ writeb(reg & 0xf, control);
+ fast_iob();
+ recovery_delay();
+ }
+ retval = readb(control);
+ recovery_delay();
+ return retval;
+}
+
+static void write_zsreg(struct zs_port *zport, int reg, u8 value)
+{
+ void __iomem *control = zport->port.membase + ZS_CHAN_IO_OFFSET;
+
+ if (reg != 0) {
+ writeb(reg & 0xf, control);
+ fast_iob(); recovery_delay();
+ }
+ writeb(value, control);
+ fast_iob();
+ recovery_delay();
+ return;
+}
+
+static u8 read_zsdata(struct zs_port *zport)
+{
+ void __iomem *data = zport->port.membase +
+ ZS_CHAN_IO_STRIDE + ZS_CHAN_IO_OFFSET;
+ u8 retval;
+
+ retval = readb(data);
+ recovery_delay();
+ return retval;
+}
+
+static void write_zsdata(struct zs_port *zport, u8 value)
+{
+ void __iomem *data = zport->port.membase +
+ ZS_CHAN_IO_STRIDE + ZS_CHAN_IO_OFFSET;
+
+ writeb(value, data);
+ fast_iob();
+ recovery_delay();
+ return;
+}
+
+#ifdef ZS_DEBUG_REGS
+void zs_dump(void)
+{
+ struct zs_port *zport;
+ int i, j;
+
+ for (i = 0; i < ZS_NUM_SCCS * ZS_NUM_CHAN; i++) {
+ zport = &zs_sccs[i / ZS_NUM_CHAN].zport[i % ZS_NUM_CHAN];
+
+ if (!zport->scc)
+ continue;
+
+ for (j = 0; j < 16; j++)
+ printk("W%-2d = 0x%02x\t", j, zport->regs[j]);
+ printk("\n");
+ for (j = 0; j < 16; j++)
+ printk("R%-2d = 0x%02x\t", j, read_zsreg(zport, j));
+ printk("\n\n");
+ }
+}
+#endif
+
+
+static void zs_spin_lock_cond_irq(spinlock_t *lock, int irq)
+{
+ if (irq)
+ spin_lock_irq(lock);
+ else
+ spin_lock(lock);
+}
+
+static void zs_spin_unlock_cond_irq(spinlock_t *lock, int irq)
+{
+ if (irq)
+ spin_unlock_irq(lock);
+ else
+ spin_unlock(lock);
+}
+
+static int zs_receive_drain(struct zs_port *zport)
+{
+ int loops = 10000;
+
+ while ((read_zsreg(zport, R0) & Rx_CH_AV) && loops--)
+ read_zsdata(zport);
+ return loops;
+}
+
+static int zs_transmit_drain(struct zs_port *zport, int irq)
+{
+ struct zs_scc *scc = zport->scc;
+ int loops = 10000;
+
+ while (!(read_zsreg(zport, R0) & Tx_BUF_EMP) && loops--) {
+ zs_spin_unlock_cond_irq(&scc->zlock, irq);
+ udelay(2);
+ zs_spin_lock_cond_irq(&scc->zlock, irq);
+ }
+ return loops;
+}
+
+static int zs_line_drain(struct zs_port *zport, int irq)
+{
+ struct zs_scc *scc = zport->scc;
+ int loops = 10000;
+
+ while (!(read_zsreg(zport, R1) & ALL_SNT) && loops--) {
+ zs_spin_unlock_cond_irq(&scc->zlock, irq);
+ udelay(2);
+ zs_spin_lock_cond_irq(&scc->zlock, irq);
+ }
+ return loops;
+}
+
+
+static void load_zsregs(struct zs_port *zport, u8 *regs, int irq)
+{
+ /* Let the current transmission finish. */
+ zs_line_drain(zport, irq);
+ /* Load 'em up. */
+ write_zsreg(zport, R3, regs[3] & ~RxENABLE);
+ write_zsreg(zport, R5, regs[5] & ~TxENAB);
+ write_zsreg(zport, R4, regs[4]);
+ write_zsreg(zport, R9, regs[9]);
+ write_zsreg(zport, R1, regs[1]);
+ write_zsreg(zport, R2, regs[2]);
+ write_zsreg(zport, R10, regs[10]);
+ write_zsreg(zport, R14, regs[14] & ~BRENABL);
+ write_zsreg(zport, R11, regs[11]);
+ write_zsreg(zport, R12, regs[12]);
+ write_zsreg(zport, R13, regs[13]);
+ write_zsreg(zport, R14, regs[14]);
+ write_zsreg(zport, R15, regs[15]);
+ if (regs[3] & RxENABLE)
+ write_zsreg(zport, R3, regs[3]);
+ if (regs[5] & TxENAB)
+ write_zsreg(zport, R5, regs[5]);
+ return;
+}
+
+
+/*
+ * Status handling routines.
+ */
+
+/*
+ * zs_tx_empty() -- get the transmitter empty status
+ *
+ * Purpose: Let user call ioctl() to get info when the UART physically
+ * is emptied. On bus types like RS485, the transmitter must
+ * release the bus after transmitting. This must be done when
+ * the transmit shift register is empty, not be done when the
+ * transmit holding register is empty. This functionality
+ * allows an RS485 driver to be written in user space.
+ */
+static unsigned int zs_tx_empty(struct uart_port *uport)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ unsigned long flags;
+ u8 status;
+
+ spin_lock_irqsave(&scc->zlock, flags);
+ status = read_zsreg(zport, R1);
+ spin_unlock_irqrestore(&scc->zlock, flags);
+
+ return status & ALL_SNT ? TIOCSER_TEMT : 0;
+}
+
+static unsigned int zs_raw_get_ab_mctrl(struct zs_port *zport_a,
+ struct zs_port *zport_b)
+{
+ u8 status_a, status_b;
+ unsigned int mctrl;
+
+ status_a = read_zsreg(zport_a, R0);
+ status_b = read_zsreg(zport_b, R0);
+
+ mctrl = ((status_b & CTS) ? TIOCM_CTS : 0) |
+ ((status_b & DCD) ? TIOCM_CAR : 0) |
+ ((status_a & DCD) ? TIOCM_RNG : 0) |
+ ((status_a & SYNC_HUNT) ? TIOCM_DSR : 0);
+
+ return mctrl;
+}
+
+static unsigned int zs_raw_get_mctrl(struct zs_port *zport)
+{
+ struct zs_port *zport_a = &zport->scc->zport[ZS_CHAN_A];
+
+ return zport != zport_a ? zs_raw_get_ab_mctrl(zport_a, zport) : 0;
+}
+
+static unsigned int zs_raw_xor_mctrl(struct zs_port *zport)
+{
+ struct zs_port *zport_a = &zport->scc->zport[ZS_CHAN_A];
+ unsigned int mmask, mctrl, delta;
+ u8 mask_a, mask_b;
+
+ if (zport == zport_a)
+ return 0;
+
+ mask_a = zport_a->regs[15];
+ mask_b = zport->regs[15];
+
+ mmask = ((mask_b & CTSIE) ? TIOCM_CTS : 0) |
+ ((mask_b & DCDIE) ? TIOCM_CAR : 0) |
+ ((mask_a & DCDIE) ? TIOCM_RNG : 0) |
+ ((mask_a & SYNCIE) ? TIOCM_DSR : 0);
+
+ mctrl = zport->mctrl;
+ if (mmask) {
+ mctrl &= ~mmask;
+ mctrl |= zs_raw_get_ab_mctrl(zport_a, zport) & mmask;
+ }
+
+ delta = mctrl ^ zport->mctrl;
+ if (delta)
+ zport->mctrl = mctrl;
+
+ return delta;
+}
+
+static unsigned int zs_get_mctrl(struct uart_port *uport)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ unsigned int mctrl;
+
+ spin_lock(&scc->zlock);
+ mctrl = zs_raw_get_mctrl(zport);
+ spin_unlock(&scc->zlock);
+
+ return mctrl;
+}
+
+static void zs_set_mctrl(struct uart_port *uport, unsigned int mctrl)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
+ u8 oldloop, newloop;
+
+ spin_lock(&scc->zlock);
+ if (zport != zport_a) {
+ if (mctrl & TIOCM_DTR)
+ zport_a->regs[5] |= DTR;
+ else
+ zport_a->regs[5] &= ~DTR;
+ if (mctrl & TIOCM_RTS)
+ zport_a->regs[5] |= RTS;
+ else
+ zport_a->regs[5] &= ~RTS;
+ write_zsreg(zport_a, R5, zport_a->regs[5]);
+ }
+
+ /* Rarely modified, so don't poke at hardware unless necessary. */
+ oldloop = zport->regs[14];
+ newloop = oldloop;
+ if (mctrl & TIOCM_LOOP)
+ newloop |= LOOPBAK;
+ else
+ newloop &= ~LOOPBAK;
+ if (newloop != oldloop) {
+ zport->regs[14] = newloop;
+ write_zsreg(zport, R14, zport->regs[14]);
+ }
+ spin_unlock(&scc->zlock);
+}
+
+static void zs_raw_stop_tx(struct zs_port *zport)
+{
+ write_zsreg(zport, R0, RES_Tx_P);
+ zport->tx_stopped = 1;
+}
+
+static void zs_stop_tx(struct uart_port *uport)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+
+ spin_lock(&scc->zlock);
+ zs_raw_stop_tx(zport);
+ spin_unlock(&scc->zlock);
+}
+
+static void zs_raw_transmit_chars(struct zs_port *);
+
+static void zs_start_tx(struct uart_port *uport)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+
+ spin_lock(&scc->zlock);
+ if (zport->tx_stopped) {
+ zs_transmit_drain(zport, 0);
+ zport->tx_stopped = 0;
+ zs_raw_transmit_chars(zport);
+ }
+ spin_unlock(&scc->zlock);
+}
+
+static void zs_stop_rx(struct uart_port *uport)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
+
+ spin_lock(&scc->zlock);
+ zport->regs[15] &= ~BRKIE;
+ zport->regs[1] &= ~(RxINT_MASK | TxINT_ENAB);
+ zport->regs[1] |= RxINT_DISAB;
+
+ if (zport != zport_a) {
+ /* A-side DCD tracks RI and SYNC tracks DSR. */
+ zport_a->regs[15] &= ~(DCDIE | SYNCIE);
+ write_zsreg(zport_a, R15, zport_a->regs[15]);
+ if (!(zport_a->regs[15] & BRKIE)) {
+ zport_a->regs[1] &= ~EXT_INT_ENAB;
+ write_zsreg(zport_a, R1, zport_a->regs[1]);
+ }
+
+ /* This-side DCD tracks DCD and CTS tracks CTS. */
+ zport->regs[15] &= ~(DCDIE | CTSIE);
+ zport->regs[1] &= ~EXT_INT_ENAB;
+ } else {
+ /* DCD tracks RI and SYNC tracks DSR for the B side. */
+ if (!(zport->regs[15] & (DCDIE | SYNCIE)))
+ zport->regs[1] &= ~EXT_INT_ENAB;
+ }
+
+ write_zsreg(zport, R15, zport->regs[15]);
+ write_zsreg(zport, R1, zport->regs[1]);
+ spin_unlock(&scc->zlock);
+}
+
+static void zs_enable_ms(struct uart_port *uport)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
+
+ if (zport == zport_a)
+ return;
+
+ spin_lock(&scc->zlock);
+
+ /* Clear Ext interrupts if not being handled already. */
+ if (!(zport_a->regs[1] & EXT_INT_ENAB))
+ write_zsreg(zport_a, R0, RES_EXT_INT);
+
+ /* A-side DCD tracks RI and SYNC tracks DSR. */
+ zport_a->regs[1] |= EXT_INT_ENAB;
+ zport_a->regs[15] |= DCDIE | SYNCIE;
+
+ /* This-side DCD tracks DCD and CTS tracks CTS. */
+ zport->regs[15] |= DCDIE | CTSIE;
+
+ zs_raw_xor_mctrl(zport);
+
+ write_zsreg(zport_a, R1, zport_a->regs[1]);
+ write_zsreg(zport_a, R15, zport_a->regs[15]);
+ write_zsreg(zport, R15, zport->regs[15]);
+ spin_unlock(&scc->zlock);
+}
+
+static void zs_break_ctl(struct uart_port *uport, int break_state)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ unsigned long flags;
+
+ spin_lock_irqsave(&scc->zlock, flags);
+ if (break_state == -1)
+ zport->regs[5] |= SND_BRK;
+ else
+ zport->regs[5] &= ~SND_BRK;
+ write_zsreg(zport, R5, zport->regs[5]);
+ spin_unlock_irqrestore(&scc->zlock, flags);
+}
+
+
+/*
+ * Interrupt handling routines.
+ */
+#define Rx_BRK 0x0100 /* BREAK event software flag. */
+#define Rx_SYS 0x0200 /* SysRq event software flag. */
+
+static void zs_receive_chars(struct zs_port *zport)
+{
+ struct uart_port *uport = &zport->port;
+ struct zs_scc *scc = zport->scc;
+ struct uart_icount *icount;
+ unsigned int avail, status, ch, flag;
+ int count;
+
+ for (count = 16; count; count--) {
+ spin_lock(&scc->zlock);
+ avail = read_zsreg(zport, R0) & Rx_CH_AV;
+ spin_unlock(&scc->zlock);
+ if (!avail)
+ break;
+
+ spin_lock(&scc->zlock);
+ status = read_zsreg(zport, R1) & (Rx_OVR | FRM_ERR | PAR_ERR);
+ ch = read_zsdata(zport);
+ spin_unlock(&scc->zlock);
+
+ flag = TTY_NORMAL;
+
+ icount = &uport->icount;
+ icount->rx++;
+
+ /* Handle the null char got when BREAK is removed. */
+ if (!ch)
+ status |= zport->tty_break;
+ if (unlikely(status &
+ (Rx_OVR | FRM_ERR | PAR_ERR | Rx_SYS | Rx_BRK))) {
+ zport->tty_break = 0;
+
+ /* Reset the error indication. */
+ if (status & (Rx_OVR | FRM_ERR | PAR_ERR)) {
+ spin_lock(&scc->zlock);
+ write_zsreg(zport, R0, ERR_RES);
+ spin_unlock(&scc->zlock);
+ }
+
+ if (status & (Rx_SYS | Rx_BRK)) {
+ icount->brk++;
+ /* SysRq discards the null char. */
+ if (status & Rx_SYS)
+ continue;
+ } else if (status & FRM_ERR)
+ icount->frame++;
+ else if (status & PAR_ERR)
+ icount->parity++;
+ if (status & Rx_OVR)
+ icount->overrun++;
+
+ status &= uport->read_status_mask;
+ if (status & Rx_BRK)
+ flag = TTY_BREAK;
+ else if (status & FRM_ERR)
+ flag = TTY_FRAME;
+ else if (status & PAR_ERR)
+ flag = TTY_PARITY;
+ }
+
+ if (uart_handle_sysrq_char(uport, ch))
+ continue;
+
+ uart_insert_char(uport, status, Rx_OVR, ch, flag);
+ }
+
+ tty_flip_buffer_push(uport->info->tty);
+}
+
+static void zs_raw_transmit_chars(struct zs_port *zport)
+{
+ struct circ_buf *xmit = &zport->port.info->xmit;
+
+ /* XON/XOFF chars. */
+ if (zport->port.x_char) {
+ write_zsdata(zport, zport->port.x_char);
+ zport->port.icount.tx++;
+ zport->port.x_char = 0;
+ return;
+ }
+
+ /* If nothing to do or stopped or hardware stopped. */
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&zport->port)) {
+ zs_raw_stop_tx(zport);
+ return;
+ }
+
+ /* Send char. */
+ write_zsdata(zport, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ zport->port.icount.tx++;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&zport->port);
+
+ /* Are we are done? */
+ if (uart_circ_empty(xmit))
+ zs_raw_stop_tx(zport);
+}
+
+static void zs_transmit_chars(struct zs_port *zport)
+{
+ struct zs_scc *scc = zport->scc;
+
+ spin_lock(&scc->zlock);
+ zs_raw_transmit_chars(zport);
+ spin_unlock(&scc->zlock);
+}
+
+static void zs_status_handle(struct zs_port *zport, struct zs_port *zport_a)
+{
+ struct uart_port *uport = &zport->port;
+ struct zs_scc *scc = zport->scc;
+ unsigned int delta;
+ u8 status, brk;
+
+ spin_lock(&scc->zlock);
+
+ /* Get status from Read Register 0. */
+ status = read_zsreg(zport, R0);
+
+ if (zport->regs[15] & BRKIE) {
+ brk = status & BRK_ABRT;
+ if (brk && !zport->brk) {
+ spin_unlock(&scc->zlock);
+ if (uart_handle_break(uport))
+ zport->tty_break = Rx_SYS;
+ else
+ zport->tty_break = Rx_BRK;
+ spin_lock(&scc->zlock);
+ }
+ zport->brk = brk;
+ }
+
+ if (zport != zport_a) {
+ delta = zs_raw_xor_mctrl(zport);
+ spin_unlock(&scc->zlock);
+
+ if (delta & TIOCM_CTS)
+ uart_handle_cts_change(uport,
+ zport->mctrl & TIOCM_CTS);
+ if (delta & TIOCM_CAR)
+ uart_handle_dcd_change(uport,
+ zport->mctrl & TIOCM_CAR);
+ if (delta & TIOCM_RNG)
+ uport->icount.dsr++;
+ if (delta & TIOCM_DSR)
+ uport->icount.rng++;
+
+ if (delta)
+ wake_up_interruptible(&uport->info->delta_msr_wait);
+
+ spin_lock(&scc->zlock);
+ }
+
+ /* Clear the status condition... */
+ write_zsreg(zport, R0, RES_EXT_INT);
+
+ spin_unlock(&scc->zlock);
+}
+
+/*
+ * This is the Z85C30 driver's generic interrupt routine.
+ */
+static irqreturn_t zs_interrupt(int irq, void *dev_id)
+{
+ struct zs_scc *scc = dev_id;
+ struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
+ struct zs_port *zport_b = &scc->zport[ZS_CHAN_B];
+ irqreturn_t status = IRQ_NONE;
+ u8 zs_intreg;
+ int count;
+
+ /*
+ * NOTE: The read register 3, which holds the irq status,
+ * does so for both channels on each chip. Although
+ * the status value itself must be read from the A
+ * channel and is only valid when read from channel A.
+ * Yes... broken hardware...
+ */
+ for (count = 16; count; count--) {
+ spin_lock(&scc->zlock);
+ zs_intreg = read_zsreg(zport_a, R3);
+ spin_unlock(&scc->zlock);
+ if (!zs_intreg)
+ break;
+
+ /*
+ * We do not like losing characters, so we prioritise
+ * interrupt sources a little bit differently than
+ * the SCC would, was it allowed to.
+ */
+ if (zs_intreg & CHBRxIP)
+ zs_receive_chars(zport_b);
+ if (zs_intreg & CHARxIP)
+ zs_receive_chars(zport_a);
+ if (zs_intreg & CHBEXT)
+ zs_status_handle(zport_b, zport_a);
+ if (zs_intreg & CHAEXT)
+ zs_status_handle(zport_a, zport_a);
+ if (zs_intreg & CHBTxIP)
+ zs_transmit_chars(zport_b);
+ if (zs_intreg & CHATxIP)
+ zs_transmit_chars(zport_a);
+
+ status = IRQ_HANDLED;
+ }
+
+ return status;
+}
+
+
+/*
+ * Finally, routines used to initialize the serial port.
+ */
+static int zs_startup(struct uart_port *uport)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ unsigned long flags;
+ int irq_guard;
+ int ret;
+
+ irq_guard = atomic_add_return(1, &scc->irq_guard);
+ if (irq_guard == 1) {
+ ret = request_irq(zport->port.irq, zs_interrupt,
+ IRQF_SHARED, "scc", scc);
+ if (ret) {
+ atomic_add(-1, &scc->irq_guard);
+ printk(KERN_ERR "zs: can't get irq %d\n",
+ zport->port.irq);
+ return ret;
+ }
+ }
+
+ spin_lock_irqsave(&scc->zlock, flags);
+
+ /* Clear the receive FIFO. */
+ zs_receive_drain(zport);
+
+ /* Clear the interrupt registers. */
+ write_zsreg(zport, R0, ERR_RES);
+ write_zsreg(zport, R0, RES_Tx_P);
+ /* But Ext only if not being handled already. */
+ if (!(zport->regs[1] & EXT_INT_ENAB))
+ write_zsreg(zport, R0, RES_EXT_INT);
+
+ /* Finally, enable sequencing and interrupts. */
+ zport->regs[1] &= ~RxINT_MASK;
+ zport->regs[1] |= RxINT_ALL | TxINT_ENAB | EXT_INT_ENAB;
+ zport->regs[3] |= RxENABLE;
+ zport->regs[5] |= TxENAB;
+ zport->regs[15] |= BRKIE;
+ write_zsreg(zport, R1, zport->regs[1]);
+ write_zsreg(zport, R3, zport->regs[3]);
+ write_zsreg(zport, R5, zport->regs[5]);
+ write_zsreg(zport, R15, zport->regs[15]);
+
+ /* Record the current state of RR0. */
+ zport->mctrl = zs_raw_get_mctrl(zport);
+ zport->brk = read_zsreg(zport, R0) & BRK_ABRT;
+
+ zport->tx_stopped = 1;
+
+ spin_unlock_irqrestore(&scc->zlock, flags);
+
+ return 0;
+}
+
+static void zs_shutdown(struct uart_port *uport)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ unsigned long flags;
+ int irq_guard;
+
+ spin_lock_irqsave(&scc->zlock, flags);
+
+ zport->regs[5] &= ~TxENAB;
+ zport->regs[3] &= ~RxENABLE;
+ write_zsreg(zport, R5, zport->regs[5]);
+ write_zsreg(zport, R3, zport->regs[3]);
+
+ spin_unlock_irqrestore(&scc->zlock, flags);
+
+ irq_guard = atomic_add_return(-1, &scc->irq_guard);
+ if (!irq_guard)
+ free_irq(zport->port.irq, scc);
+}
+
+
+static void zs_reset(struct zs_port *zport)
+{
+ struct zs_scc *scc = zport->scc;
+ int irq;
+ unsigned long flags;
+
+ spin_lock_irqsave(&scc->zlock, flags);
+ irq = !irqs_disabled_flags(flags);
+ if (!scc->initialised) {
+ /* Reset the pointer first, just in case... */
+ read_zsreg(zport, R0);
+ /* And let the current transmission finish. */
+ zs_line_drain(zport, irq);
+ write_zsreg(zport, R9, FHWRES);
+ udelay(10);
+ write_zsreg(zport, R9, 0);
+ scc->initialised = 1;
+ }
+ load_zsregs(zport, zport->regs, irq);
+ spin_unlock_irqrestore(&scc->zlock, flags);
+}
+
+static void zs_set_termios(struct uart_port *uport, struct ktermios *termios,
+ struct ktermios *old_termios)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ struct zs_port *zport_a = &scc->zport[ZS_CHAN_A];
+ int irq;
+ unsigned int baud, brg;
+ unsigned long flags;
+
+ spin_lock_irqsave(&scc->zlock, flags);
+ irq = !irqs_disabled_flags(flags);
+
+ /* Byte size. */
+ zport->regs[3] &= ~RxNBITS_MASK;
+ zport->regs[5] &= ~TxNBITS_MASK;
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ zport->regs[3] |= Rx5;
+ zport->regs[5] |= Tx5;
+ break;
+ case CS6:
+ zport->regs[3] |= Rx6;
+ zport->regs[5] |= Tx6;
+ break;
+ case CS7:
+ zport->regs[3] |= Rx7;
+ zport->regs[5] |= Tx7;
+ break;
+ case CS8:
+ default:
+ zport->regs[3] |= Rx8;
+ zport->regs[5] |= Tx8;
+ break;
+ }
+
+ /* Parity and stop bits. */
+ zport->regs[4] &= ~(XCLK_MASK | SB_MASK | PAR_ENA | PAR_EVEN);
+ if (termios->c_cflag & CSTOPB)
+ zport->regs[4] |= SB2;
+ else
+ zport->regs[4] |= SB1;
+ if (termios->c_cflag & PARENB)
+ zport->regs[4] |= PAR_ENA;
+ if (!(termios->c_cflag & PARODD))
+ zport->regs[4] |= PAR_EVEN;
+ switch (zport->clk_mode) {
+ case 64:
+ zport->regs[4] |= X64CLK;
+ break;
+ case 32:
+ zport->regs[4] |= X32CLK;
+ break;
+ case 16:
+ zport->regs[4] |= X16CLK;
+ break;
+ case 1:
+ zport->regs[4] |= X1CLK;
+ break;
+ default:
+ BUG();
+ }
+
+ baud = uart_get_baud_rate(uport, termios, old_termios, 0,
+ uport->uartclk / zport->clk_mode / 4);
+
+ brg = ZS_BPS_TO_BRG(baud, uport->uartclk / zport->clk_mode);
+ zport->regs[12] = brg & 0xff;
+ zport->regs[13] = (brg >> 8) & 0xff;
+
+ uart_update_timeout(uport, termios->c_cflag, baud);
+
+ uport->read_status_mask = Rx_OVR;
+ if (termios->c_iflag & INPCK)
+ uport->read_status_mask |= FRM_ERR | PAR_ERR;
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ uport->read_status_mask |= Rx_BRK;
+
+ uport->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ uport->ignore_status_mask |= FRM_ERR | PAR_ERR;
+ if (termios->c_iflag & IGNBRK) {
+ uport->ignore_status_mask |= Rx_BRK;
+ if (termios->c_iflag & IGNPAR)
+ uport->ignore_status_mask |= Rx_OVR;
+ }
+
+ if (termios->c_cflag & CREAD)
+ zport->regs[3] |= RxENABLE;
+ else
+ zport->regs[3] &= ~RxENABLE;
+
+ if (zport != zport_a) {
+ if (!(termios->c_cflag & CLOCAL)) {
+ zport->regs[15] |= DCDIE;
+ } else
+ zport->regs[15] &= ~DCDIE;
+ if (termios->c_cflag & CRTSCTS) {
+ zport->regs[15] |= CTSIE;
+ } else
+ zport->regs[15] &= ~CTSIE;
+ zs_raw_xor_mctrl(zport);
+ }
+
+ /* Load up the new values. */
+ load_zsregs(zport, zport->regs, irq);
+
+ spin_unlock_irqrestore(&scc->zlock, flags);
+}
+
+
+static const char *zs_type(struct uart_port *uport)
+{
+ return "Z85C30 SCC";
+}
+
+static void zs_release_port(struct uart_port *uport)
+{
+ iounmap(uport->membase);
+ uport->membase = 0;
+ release_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE);
+}
+
+static int zs_map_port(struct uart_port *uport)
+{
+ if (!uport->membase)
+ uport->membase = ioremap_nocache(uport->mapbase,
+ ZS_CHAN_IO_SIZE);
+ if (!uport->membase) {
+ printk(KERN_ERR "zs: Cannot map MMIO\n");
+ return -ENOMEM;
+ }
+ return 0;
+}
+
+static int zs_request_port(struct uart_port *uport)
+{
+ int ret;
+
+ if (!request_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE, "scc")) {
+ printk(KERN_ERR "zs: Unable to reserve MMIO resource\n");
+ return -EBUSY;
+ }
+ ret = zs_map_port(uport);
+ if (ret) {
+ release_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE);
+ return ret;
+ }
+ return 0;
+}
+
+static void zs_config_port(struct uart_port *uport, int flags)
+{
+ struct zs_port *zport = to_zport(uport);
+
+ if (flags & UART_CONFIG_TYPE) {
+ if (zs_request_port(uport))
+ return;
+
+ uport->type = PORT_ZS;
+
+ zs_reset(zport);
+ }
+}
+
+static int zs_verify_port(struct uart_port *uport, struct serial_struct *ser)
+{
+ struct zs_port *zport = to_zport(uport);
+ int ret = 0;
+
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_ZS)
+ ret = -EINVAL;
+ if (ser->irq != uport->irq)
+ ret = -EINVAL;
+ if (ser->baud_base != uport->uartclk / zport->clk_mode / 4)
+ ret = -EINVAL;
+ return ret;
+}
+
+
+static struct uart_ops zs_ops = {
+ .tx_empty = zs_tx_empty,
+ .set_mctrl = zs_set_mctrl,
+ .get_mctrl = zs_get_mctrl,
+ .stop_tx = zs_stop_tx,
+ .start_tx = zs_start_tx,
+ .stop_rx = zs_stop_rx,
+ .enable_ms = zs_enable_ms,
+ .break_ctl = zs_break_ctl,
+ .startup = zs_startup,
+ .shutdown = zs_shutdown,
+ .set_termios = zs_set_termios,
+ .type = zs_type,
+ .release_port = zs_release_port,
+ .request_port = zs_request_port,
+ .config_port = zs_config_port,
+ .verify_port = zs_verify_port,
+};
+
+/*
+ * Initialize Z85C30 port structures.
+ */
+static int __init zs_probe_sccs(void)
+{
+ static int probed;
+ struct zs_parms zs_parms;
+ int chip, side, irq;
+ int n_chips = 0;
+ int i;
+
+ if (probed)
+ return 0;
+
+ irq = dec_interrupt[DEC_IRQ_SCC0];
+ if (irq >= 0) {
+ zs_parms.scc[n_chips] = IOASIC_SCC0;
+ zs_parms.irq[n_chips] = dec_interrupt[DEC_IRQ_SCC0];
+ n_chips++;
+ }
+ irq = dec_interrupt[DEC_IRQ_SCC1];
+ if (irq >= 0) {
+ zs_parms.scc[n_chips] = IOASIC_SCC1;
+ zs_parms.irq[n_chips] = dec_interrupt[DEC_IRQ_SCC1];
+ n_chips++;
+ }
+ if (!n_chips)
+ return -ENXIO;
+
+ probed = 1;
+
+ for (chip = 0; chip < n_chips; chip++) {
+ spin_lock_init(&zs_sccs[chip].zlock);
+ for (side = 0; side < ZS_NUM_CHAN; side++) {
+ struct zs_port *zport = &zs_sccs[chip].zport[side];
+ struct uart_port *uport = &zport->port;
+
+ zport->scc = &zs_sccs[chip];
+ zport->clk_mode = 16;
+
+ uport->irq = zs_parms.irq[chip];
+ uport->uartclk = ZS_CLOCK;
+ uport->fifosize = 1;
+ uport->iotype = UPIO_MEM;
+ uport->flags = UPF_BOOT_AUTOCONF;
+ uport->ops = &zs_ops;
+ uport->line = chip * ZS_NUM_CHAN + side;
+ uport->mapbase = dec_kn_slot_base +
+ zs_parms.scc[chip] +
+ (side ^ ZS_CHAN_B) * ZS_CHAN_IO_SIZE;
+
+ for (i = 0; i < ZS_NUM_REGS; i++)
+ zport->regs[i] = zs_init_regs[i];
+ }
+ }
+
+ return 0;
+}
+
+
+#ifdef CONFIG_SERIAL_ZS_CONSOLE
+static void zs_console_putchar(struct uart_port *uport, int ch)
+{
+ struct zs_port *zport = to_zport(uport);
+ struct zs_scc *scc = zport->scc;
+ int irq;
+ unsigned long flags;
+
+ spin_lock_irqsave(&scc->zlock, flags);
+ irq = !irqs_disabled_flags(flags);
+ if (zs_transmit_drain(zport, irq))
+ write_zsdata(zport, ch);
+ spin_unlock_irqrestore(&scc->zlock, flags);
+}
+
+/*
+ * Print a string to the serial port trying not to disturb
+ * any possible real use of the port...
+ */
+static void zs_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ int chip = co->index / ZS_NUM_CHAN, side = co->index % ZS_NUM_CHAN;
+ struct zs_port *zport = &zs_sccs[chip].zport[side];
+ struct zs_scc *scc = zport->scc;
+ unsigned long flags;
+ u8 txint, txenb;
+ int irq;
+
+ /* Disable transmit interrupts and enable the transmitter. */
+ spin_lock_irqsave(&scc->zlock, flags);
+ txint = zport->regs[1];
+ txenb = zport->regs[5];
+ if (txint & TxINT_ENAB) {
+ zport->regs[1] = txint & ~TxINT_ENAB;
+ write_zsreg(zport, R1, zport->regs[1]);
+ }
+ if (!(txenb & TxENAB)) {
+ zport->regs[5] = txenb | TxENAB;
+ write_zsreg(zport, R5, zport->regs[5]);
+ }
+ spin_unlock_irqrestore(&scc->zlock, flags);
+
+ uart_console_write(&zport->port, s, count, zs_console_putchar);
+
+ /* Restore transmit interrupts and the transmitter enable. */
+ spin_lock_irqsave(&scc->zlock, flags);
+ irq = !irqs_disabled_flags(flags);
+ zs_line_drain(zport, irq);
+ if (!(txenb & TxENAB)) {
+ zport->regs[5] &= ~TxENAB;
+ write_zsreg(zport, R5, zport->regs[5]);
+ }
+ if (txint & TxINT_ENAB) {
+ zport->regs[1] |= TxINT_ENAB;
+ write_zsreg(zport, R1, zport->regs[1]);
+ }
+ spin_unlock_irqrestore(&scc->zlock, flags);
+}
+
+/*
+ * Setup serial console baud/bits/parity. We do two things here:
+ * - construct a cflag setting for the first uart_open()
+ * - initialise the serial port
+ * Return non-zero if we didn't find a serial port.
+ */
+static int __init zs_console_setup(struct console *co, char *options)
+{
+ int chip = co->index / ZS_NUM_CHAN, side = co->index % ZS_NUM_CHAN;
+ struct zs_port *zport = &zs_sccs[chip].zport[side];
+ struct uart_port *uport = &zport->port;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+ int ret;
+
+ ret = zs_map_port(uport);
+ if (ret)
+ return ret;
+
+ zs_reset(zport);
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+ return uart_set_options(uport, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver zs_reg;
+static struct console zs_console = {
+ .name = "ttyS",
+ .write = zs_console_write,
+ .device = uart_console_device,
+ .setup = zs_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &zs_reg,
+};
+
+/*
+ * Register console.
+ */
+static int __init zs_serial_console_init(void)
+{
+ int ret;
+
+ ret = zs_probe_sccs();
+ if (ret)
+ return ret;
+ register_console(&zs_console);
+
+ return 0;
+}
+
+console_initcall(zs_serial_console_init);
+
+#define SERIAL_ZS_CONSOLE &zs_console
+#else
+#define SERIAL_ZS_CONSOLE NULL
+#endif /* CONFIG_SERIAL_ZS_CONSOLE */
+
+static struct uart_driver zs_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "serial",
+ .dev_name = "ttyS",
+ .major = TTY_MAJOR,
+ .minor = 64,
+ .nr = ZS_NUM_SCCS * ZS_NUM_CHAN,
+ .cons = SERIAL_ZS_CONSOLE,
+};
+
+/* zs_init inits the driver. */
+static int __init zs_init(void)
+{
+ int i, ret;
+
+ pr_info("%s%s\n", zs_name, zs_version);
+
+ /* Find out how many Z85C30 SCCs we have. */
+ ret = zs_probe_sccs();
+ if (ret)
+ return ret;
+
+ ret = uart_register_driver(&zs_reg);
+ if (ret)
+ return ret;
+
+ for (i = 0; i < ZS_NUM_SCCS * ZS_NUM_CHAN; i++) {
+ struct zs_scc *scc = &zs_sccs[i / ZS_NUM_CHAN];
+ struct zs_port *zport = &scc->zport[i % ZS_NUM_CHAN];
+ struct uart_port *uport = &zport->port;
+
+ if (zport->scc)
+ uart_add_one_port(&zs_reg, uport);
+ }
+
+ return 0;
+}
+
+static void __exit zs_exit(void)
+{
+ int i;
+
+ for (i = ZS_NUM_SCCS * ZS_NUM_CHAN - 1; i >= 0; i--) {
+ struct zs_scc *scc = &zs_sccs[i / ZS_NUM_CHAN];
+ struct zs_port *zport = &scc->zport[i % ZS_NUM_CHAN];
+ struct uart_port *uport = &zport->port;
+
+ if (zport->scc)
+ uart_remove_one_port(&zs_reg, uport);
+ }
+
+ uart_unregister_driver(&zs_reg);
+}
+
+module_init(zs_init);
+module_exit(zs_exit);
--- /dev/null
+/*
+ * zs.h: Definitions for the DECstation Z85C30 serial driver.
+ *
+ * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
+ * Adapted from drivers/macintosh/macserial.h by Harald Koerfgen.
+ *
+ * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ * Copyright (C) 2004, 2005, 2007 Maciej W. Rozycki
+ */
+#ifndef _SERIAL_ZS_H
+#define _SERIAL_ZS_H
+
+#ifdef __KERNEL__
+
+#define ZS_NUM_REGS 16
+
+/*
+ * This is our internal structure for each serial port's state.
+ */
+struct zs_port {
+ struct zs_scc *scc; /* Containing SCC. */
+ struct uart_port port; /* Underlying UART. */
+
+ int clk_mode; /* May be 1, 16, 32, or 64. */
+
+ unsigned int tty_break; /* Set on BREAK condition. */
+ int tx_stopped; /* Output is suspended. */
+
+ unsigned int mctrl; /* State of modem lines. */
+ u8 brk; /* BREAK state from RR0. */
+
+ u8 regs[ZS_NUM_REGS]; /* Channel write registers. */
+};
+
+/*
+ * Per-SCC state for locking and the interrupt handler.
+ */
+struct zs_scc {
+ struct zs_port zport[2];
+ spinlock_t zlock;
+ atomic_t irq_guard;
+ int initialised;
+};
+
+#endif /* __KERNEL__ */
+
+/*
+ * Conversion routines to/from brg time constants from/to bits per second.
+ */
+#define ZS_BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
+#define ZS_BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
+
+/*
+ * The Zilog register set.
+ */
+
+/* Write Register 0 (Command) */
+#define R0 0 /* Register selects */
+#define R1 1
+#define R2 2
+#define R3 3
+#define R4 4
+#define R5 5
+#define R6 6
+#define R7 7
+#define R8 8
+#define R9 9
+#define R10 10
+#define R11 11
+#define R12 12
+#define R13 13
+#define R14 14
+#define R15 15
+
+#define NULLCODE 0 /* Null Code */
+#define POINT_HIGH 0x8 /* Select upper half of registers */
+#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
+#define SEND_ABORT 0x18 /* HDLC Abort */
+#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
+#define RES_Tx_P 0x28 /* Reset TxINT Pending */
+#define ERR_RES 0x30 /* Error Reset */
+#define RES_H_IUS 0x38 /* Reset highest IUS */
+
+#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
+#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
+#define RES_EOM_L 0xC0 /* Reset EOM latch */
+
+/* Write Register 1 (Tx/Rx/Ext Int Enable and WAIT/DMA Commands) */
+#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
+#define TxINT_ENAB 0x2 /* Tx Int Enable */
+#define PAR_SPEC 0x4 /* Parity is special condition */
+
+#define RxINT_DISAB 0 /* Rx Int Disable */
+#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
+#define RxINT_ALL 0x10 /* Int on all Rx Characters or error */
+#define RxINT_ERR 0x18 /* Int on error only */
+#define RxINT_MASK 0x18
+
+#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
+#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
+#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
+
+/* Write Register 2 (Interrupt Vector) */
+
+/* Write Register 3 (Receive Parameters and Control) */
+#define RxENABLE 0x1 /* Rx Enable */
+#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
+#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
+#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
+#define ENT_HM 0x10 /* Enter Hunt Mode */
+#define AUTO_ENAB 0x20 /* Auto Enables */
+#define Rx5 0x0 /* Rx 5 Bits/Character */
+#define Rx7 0x40 /* Rx 7 Bits/Character */
+#define Rx6 0x80 /* Rx 6 Bits/Character */
+#define Rx8 0xc0 /* Rx 8 Bits/Character */
+#define RxNBITS_MASK 0xc0
+
+/* Write Register 4 (Transmit/Receive Miscellaneous Parameters and Modes) */
+#define PAR_ENA 0x1 /* Parity Enable */
+#define PAR_EVEN 0x2 /* Parity Even/Odd* */
+
+#define SYNC_ENAB 0 /* Sync Modes Enable */
+#define SB1 0x4 /* 1 stop bit/char */
+#define SB15 0x8 /* 1.5 stop bits/char */
+#define SB2 0xc /* 2 stop bits/char */
+#define SB_MASK 0xc
+
+#define MONSYNC 0 /* 8 Bit Sync character */
+#define BISYNC 0x10 /* 16 bit sync character */
+#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
+#define EXTSYNC 0x30 /* External Sync Mode */
+
+#define X1CLK 0x0 /* x1 clock mode */
+#define X16CLK 0x40 /* x16 clock mode */
+#define X32CLK 0x80 /* x32 clock mode */
+#define X64CLK 0xc0 /* x64 clock mode */
+#define XCLK_MASK 0xc0
+
+/* Write Register 5 (Transmit Parameters and Controls) */
+#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
+#define RTS 0x2 /* RTS */
+#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
+#define TxENAB 0x8 /* Tx Enable */
+#define SND_BRK 0x10 /* Send Break */
+#define Tx5 0x0 /* Tx 5 bits (or less)/character */
+#define Tx7 0x20 /* Tx 7 bits/character */
+#define Tx6 0x40 /* Tx 6 bits/character */
+#define Tx8 0x60 /* Tx 8 bits/character */
+#define TxNBITS_MASK 0x60
+#define DTR 0x80 /* DTR */
+
+/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
+
+/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
+
+/* Write Register 8 (Transmit Buffer) */
+
+/* Write Register 9 (Master Interrupt Control) */
+#define VIS 1 /* Vector Includes Status */
+#define NV 2 /* No Vector */
+#define DLC 4 /* Disable Lower Chain */
+#define MIE 8 /* Master Interrupt Enable */
+#define STATHI 0x10 /* Status high */
+#define SOFTACK 0x20 /* Software Interrupt Acknowledge */
+#define NORESET 0 /* No reset on write to R9 */
+#define CHRB 0x40 /* Reset channel B */
+#define CHRA 0x80 /* Reset channel A */
+#define FHWRES 0xc0 /* Force hardware reset */
+
+/* Write Register 10 (Miscellaneous Transmitter/Receiver Control Bits) */
+#define BIT6 1 /* 6 bit/8bit sync */
+#define LOOPMODE 2 /* SDLC Loop mode */
+#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
+#define MARKIDLE 8 /* Mark/flag on idle */
+#define GAOP 0x10 /* Go active on poll */
+#define NRZ 0 /* NRZ mode */
+#define NRZI 0x20 /* NRZI mode */
+#define FM1 0x40 /* FM1 (transition = 1) */
+#define FM0 0x60 /* FM0 (transition = 0) */
+#define CRCPS 0x80 /* CRC Preset I/O */
+
+/* Write Register 11 (Clock Mode Control) */
+#define TRxCXT 0 /* TRxC = Xtal output */
+#define TRxCTC 1 /* TRxC = Transmit clock */
+#define TRxCBR 2 /* TRxC = BR Generator Output */
+#define TRxCDP 3 /* TRxC = DPLL output */
+#define TRxCOI 4 /* TRxC O/I */
+#define TCRTxCP 0 /* Transmit clock = RTxC pin */
+#define TCTRxCP 8 /* Transmit clock = TRxC pin */
+#define TCBR 0x10 /* Transmit clock = BR Generator output */
+#define TCDPLL 0x18 /* Transmit clock = DPLL output */
+#define RCRTxCP 0 /* Receive clock = RTxC pin */
+#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
+#define RCBR 0x40 /* Receive clock = BR Generator output */
+#define RCDPLL 0x60 /* Receive clock = DPLL output */
+#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
+
+/* Write Register 12 (Lower Byte of Baud Rate Generator Time Constant) */
+
+/* Write Register 13 (Upper Byte of Baud Rate Generator Time Constant) */
+
+/* Write Register 14 (Miscellaneous Control Bits) */
+#define BRENABL 1 /* Baud rate generator enable */
+#define BRSRC 2 /* Baud rate generator source */
+#define DTRREQ 4 /* DTR/Request function */
+#define AUTOECHO 8 /* Auto Echo */
+#define LOOPBAK 0x10 /* Local loopback */
+#define SEARCH 0x20 /* Enter search mode */
+#define RMC 0x40 /* Reset missing clock */
+#define DISDPLL 0x60 /* Disable DPLL */
+#define SSBR 0x80 /* Set DPLL source = BR generator */
+#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
+#define SFMM 0xc0 /* Set FM mode */
+#define SNRZI 0xe0 /* Set NRZI mode */
+
+/* Write Register 15 (External/Status Interrupt Control) */
+#define WR7P_EN 1 /* WR7 Prime SDLC Feature Enable */
+#define ZCIE 2 /* Zero count IE */
+#define DCDIE 8 /* DCD IE */
+#define SYNCIE 0x10 /* Sync/hunt IE */
+#define CTSIE 0x20 /* CTS IE */
+#define TxUIE 0x40 /* Tx Underrun/EOM IE */
+#define BRKIE 0x80 /* Break/Abort IE */
+
+
+/* Read Register 0 (Transmit/Receive Buffer Status and External Status) */
+#define Rx_CH_AV 0x1 /* Rx Character Available */
+#define ZCOUNT 0x2 /* Zero count */
+#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
+#define DCD 0x8 /* DCD */
+#define SYNC_HUNT 0x10 /* Sync/hunt */
+#define CTS 0x20 /* CTS */
+#define TxEOM 0x40 /* Tx underrun */
+#define BRK_ABRT 0x80 /* Break/Abort */
+
+/* Read Register 1 (Special Receive Condition Status) */
+#define ALL_SNT 0x1 /* All sent */
+/* Residue Data for 8 Rx bits/char programmed */
+#define RES3 0x8 /* 0/3 */
+#define RES4 0x4 /* 0/4 */
+#define RES5 0xc /* 0/5 */
+#define RES6 0x2 /* 0/6 */
+#define RES7 0xa /* 0/7 */
+#define RES8 0x6 /* 0/8 */
+#define RES18 0xe /* 1/8 */
+#define RES28 0x0 /* 2/8 */
+/* Special Rx Condition Interrupts */
+#define PAR_ERR 0x10 /* Parity Error */
+#define Rx_OVR 0x20 /* Rx Overrun Error */
+#define FRM_ERR 0x40 /* CRC/Framing Error */
+#define END_FR 0x80 /* End of Frame (SDLC) */
+
+/* Read Register 2 (Interrupt Vector (WR2) -- channel A). */
+
+/* Read Register 2 (Modified Interrupt Vector -- channel B). */
+
+/* Read Register 3 (Interrupt Pending Bits -- channel A only). */
+#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
+#define CHBTxIP 0x2 /* Channel B Tx IP */
+#define CHBRxIP 0x4 /* Channel B Rx IP */
+#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
+#define CHATxIP 0x10 /* Channel A Tx IP */
+#define CHARxIP 0x20 /* Channel A Rx IP */
+
+/* Read Register 6 (SDLC FIFO Status and Byte Count LSB) */
+
+/* Read Register 7 (SDLC FIFO Status and Byte Count MSB) */
+
+/* Read Register 8 (Receive Data) */
+
+/* Read Register 10 (Miscellaneous Status Bits) */
+#define ONLOOP 2 /* On loop */
+#define LOOPSEND 0x10 /* Loop sending */
+#define CLK2MIS 0x40 /* Two clocks missing */
+#define CLK1MIS 0x80 /* One clock missing */
+
+/* Read Register 12 (Lower Byte of Baud Rate Generator Constant (WR12)) */
+
+/* Read Register 13 (Upper Byte of Baud Rate Generator Constant (WR13) */
+
+/* Read Register 15 (External/Status Interrupt Control (WR15)) */
+
+#endif /* _SERIAL_ZS_H */
# Object file lists.
obj-$(CONFIG_TC) += tc.o tc-driver.o
-obj-$(CONFIG_ZS) += zs.o
obj-$(CONFIG_VT) += lk201.o lk201-map.o lk201-remap.o
$(obj)/lk201-map.o: $(obj)/lk201-map.c
+++ /dev/null
-/*
- * decserial.c: Serial port driver for IOASIC DECstations.
- *
- * Derived from drivers/sbus/char/sunserial.c by Paul Mackerras.
- * Derived from drivers/macintosh/macserial.c by Harald Koerfgen.
- *
- * DECstation changes
- * Copyright (C) 1998-2000 Harald Koerfgen
- * Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005 Maciej W. Rozycki
- *
- * For the rest of the code the original Copyright applies:
- * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- *
- *
- * Note: for IOASIC systems the wiring is as follows:
- *
- * mouse/keyboard:
- * DIN-7 MJ-4 signal SCC
- * 2 1 TxD <- A.TxD
- * 3 4 RxD -> A.RxD
- *
- * EIA-232/EIA-423:
- * DB-25 MMJ-6 signal SCC
- * 2 2 TxD <- B.TxD
- * 3 5 RxD -> B.RxD
- * 4 RTS <- ~A.RTS
- * 5 CTS -> ~B.CTS
- * 6 6 DSR -> ~A.SYNC
- * 8 CD -> ~B.DCD
- * 12 DSRS(DCE) -> ~A.CTS (*)
- * 15 TxC -> B.TxC
- * 17 RxC -> B.RxC
- * 20 1 DTR <- ~A.DTR
- * 22 RI -> ~A.DCD
- * 23 DSRS(DTE) <- ~B.RTS
- *
- * (*) EIA-232 defines the signal at this pin to be SCD, while DSRS(DCE)
- * is shared with DSRS(DTE) at pin 23.
- */
-
-#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/sched.h>
-#include <linux/timer.h>
-#include <linux/interrupt.h>
-#include <linux/tty.h>
-#include <linux/tty_flip.h>
-#include <linux/major.h>
-#include <linux/string.h>
-#include <linux/fcntl.h>
-#include <linux/mm.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/spinlock.h>
-#ifdef CONFIG_SERIAL_DEC_CONSOLE
-#include <linux/console.h>
-#endif
-
-#include <asm/io.h>
-#include <asm/pgtable.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-#include <asm/bootinfo.h>
-
-#include <asm/dec/interrupts.h>
-#include <asm/dec/ioasic_addrs.h>
-#include <asm/dec/machtype.h>
-#include <asm/dec/serial.h>
-#include <asm/dec/system.h>
-
-#ifdef CONFIG_KGDB
-#include <asm/kgdb.h>
-#endif
-#ifdef CONFIG_MAGIC_SYSRQ
-#include <linux/sysrq.h>
-#endif
-
-#include "zs.h"
-
-/*
- * It would be nice to dynamically allocate everything that
- * depends on NUM_SERIAL, so we could support any number of
- * Z8530s, but for now...
- */
-#define NUM_SERIAL 2 /* Max number of ZS chips supported */
-#define NUM_CHANNELS (NUM_SERIAL * 2) /* 2 channels per chip */
-#define CHANNEL_A_NR (zs_parms->channel_a_offset > zs_parms->channel_b_offset)
- /* Number of channel A in the chip */
-#define ZS_CHAN_IO_SIZE 8
-#define ZS_CLOCK 7372800 /* Z8530 RTxC input clock rate */
-
-#define RECOVERY_DELAY udelay(2)
-
-struct zs_parms {
- unsigned long scc0;
- unsigned long scc1;
- int channel_a_offset;
- int channel_b_offset;
- int irq0;
- int irq1;
- int clock;
-};
-
-static struct zs_parms *zs_parms;
-
-#ifdef CONFIG_MACH_DECSTATION
-static struct zs_parms ds_parms = {
- scc0 : IOASIC_SCC0,
- scc1 : IOASIC_SCC1,
- channel_a_offset : 1,
- channel_b_offset : 9,
- irq0 : -1,
- irq1 : -1,
- clock : ZS_CLOCK
-};
-#endif
-
-#ifdef CONFIG_MACH_DECSTATION
-#define DS_BUS_PRESENT (IOASIC)
-#else
-#define DS_BUS_PRESENT 0
-#endif
-
-#define BUS_PRESENT (DS_BUS_PRESENT)
-
-DEFINE_SPINLOCK(zs_lock);
-
-struct dec_zschannel zs_channels[NUM_CHANNELS];
-struct dec_serial zs_soft[NUM_CHANNELS];
-int zs_channels_found;
-struct dec_serial *zs_chain; /* list of all channels */
-
-struct tty_struct zs_ttys[NUM_CHANNELS];
-
-#ifdef CONFIG_SERIAL_DEC_CONSOLE
-static struct console zs_console;
-#endif
-#if defined(CONFIG_SERIAL_DEC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) && \
- !defined(MODULE)
-static unsigned long break_pressed; /* break, really ... */
-#endif
-
-static unsigned char zs_init_regs[16] __initdata = {
- 0, /* write 0 */
- 0, /* write 1 */
- 0, /* write 2 */
- 0, /* write 3 */
- (X16CLK), /* write 4 */
- 0, /* write 5 */
- 0, 0, 0, /* write 6, 7, 8 */
- (MIE | DLC | NV), /* write 9 */
- (NRZ), /* write 10 */
- (TCBR | RCBR), /* write 11 */
- 0, 0, /* BRG time constant, write 12 + 13 */
- (BRSRC | BRENABL), /* write 14 */
- 0 /* write 15 */
-};
-
-static struct tty_driver *serial_driver;
-
-/* serial subtype definitions */
-#define SERIAL_TYPE_NORMAL 1
-
-/* number of characters left in xmit buffer before we ask for more */
-#define WAKEUP_CHARS 256
-
-/*
- * Debugging.
- */
-#undef SERIAL_DEBUG_OPEN
-#undef SERIAL_DEBUG_FLOW
-#undef SERIAL_DEBUG_THROTTLE
-#undef SERIAL_PARANOIA_CHECK
-
-#undef ZS_DEBUG_REGS
-
-#ifdef SERIAL_DEBUG_THROTTLE
-#define _tty_name(tty,buf) tty_name(tty,buf)
-#endif
-
-#define RS_STROBE_TIME 10
-#define RS_ISR_PASS_LIMIT 256
-
-static void probe_sccs(void);
-static void change_speed(struct dec_serial *info);
-static void rs_wait_until_sent(struct tty_struct *tty, int timeout);
-
-static inline int serial_paranoia_check(struct dec_serial *info,
- char *name, const char *routine)
-{
-#ifdef SERIAL_PARANOIA_CHECK
- static const char *badmagic =
- "Warning: bad magic number for serial struct %s in %s\n";
- static const char *badinfo =
- "Warning: null mac_serial for %s in %s\n";
-
- if (!info) {
- printk(badinfo, name, routine);
- return 1;
- }
- if (info->magic != SERIAL_MAGIC) {
- printk(badmagic, name, routine);
- return 1;
- }
-#endif
- return 0;
-}
-
-/*
- * This is used to figure out the divisor speeds and the timeouts
- */
-static int baud_table[] = {
- 0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
- 9600, 19200, 38400, 57600, 115200, 0 };
-
-/*
- * Reading and writing Z8530 registers.
- */
-static inline unsigned char read_zsreg(struct dec_zschannel *channel,
- unsigned char reg)
-{
- unsigned char retval;
-
- if (reg != 0) {
- *channel->control = reg & 0xf;
- fast_iob(); RECOVERY_DELAY;
- }
- retval = *channel->control;
- RECOVERY_DELAY;
- return retval;
-}
-
-static inline void write_zsreg(struct dec_zschannel *channel,
- unsigned char reg, unsigned char value)
-{
- if (reg != 0) {
- *channel->control = reg & 0xf;
- fast_iob(); RECOVERY_DELAY;
- }
- *channel->control = value;
- fast_iob(); RECOVERY_DELAY;
- return;
-}
-
-static inline unsigned char read_zsdata(struct dec_zschannel *channel)
-{
- unsigned char retval;
-
- retval = *channel->data;
- RECOVERY_DELAY;
- return retval;
-}
-
-static inline void write_zsdata(struct dec_zschannel *channel,
- unsigned char value)
-{
- *channel->data = value;
- fast_iob(); RECOVERY_DELAY;
- return;
-}
-
-static inline void load_zsregs(struct dec_zschannel *channel,
- unsigned char *regs)
-{
-/* ZS_CLEARERR(channel);
- ZS_CLEARFIFO(channel); */
- /* Load 'em up */
- write_zsreg(channel, R3, regs[R3] & ~RxENABLE);
- write_zsreg(channel, R5, regs[R5] & ~TxENAB);
- write_zsreg(channel, R4, regs[R4]);
- write_zsreg(channel, R9, regs[R9]);
- write_zsreg(channel, R1, regs[R1]);
- write_zsreg(channel, R2, regs[R2]);
- write_zsreg(channel, R10, regs[R10]);
- write_zsreg(channel, R11, regs[R11]);
- write_zsreg(channel, R12, regs[R12]);
- write_zsreg(channel, R13, regs[R13]);
- write_zsreg(channel, R14, regs[R14]);
- write_zsreg(channel, R15, regs[R15]);
- write_zsreg(channel, R3, regs[R3]);
- write_zsreg(channel, R5, regs[R5]);
- return;
-}
-
-/* Sets or clears DTR/RTS on the requested line */
-static inline void zs_rtsdtr(struct dec_serial *info, int which, int set)
-{
- unsigned long flags;
-
- spin_lock_irqsave(&zs_lock, flags);
- if (info->zs_channel != info->zs_chan_a) {
- if (set) {
- info->zs_chan_a->curregs[5] |= (which & (RTS | DTR));
- } else {
- info->zs_chan_a->curregs[5] &= ~(which & (RTS | DTR));
- }
- write_zsreg(info->zs_chan_a, 5, info->zs_chan_a->curregs[5]);
- }
- spin_unlock_irqrestore(&zs_lock, flags);
-}
-
-/* Utility routines for the Zilog */
-static inline int get_zsbaud(struct dec_serial *ss)
-{
- struct dec_zschannel *channel = ss->zs_channel;
- int brg;
-
- /* The baud rate is split up between two 8-bit registers in
- * what is termed 'BRG time constant' format in my docs for
- * the chip, it is a function of the clk rate the chip is
- * receiving which happens to be constant.
- */
- brg = (read_zsreg(channel, 13) << 8);
- brg |= read_zsreg(channel, 12);
- return BRG_TO_BPS(brg, (zs_parms->clock/(ss->clk_divisor)));
-}
-
-/* On receive, this clears errors and the receiver interrupts */
-static inline void rs_recv_clear(struct dec_zschannel *zsc)
-{
- write_zsreg(zsc, 0, ERR_RES);
- write_zsreg(zsc, 0, RES_H_IUS); /* XXX this is unnecessary */
-}
-
-/*
- * ----------------------------------------------------------------------
- *
- * Here starts the interrupt handling routines. All of the following
- * subroutines are declared as inline and are folded into
- * rs_interrupt(). They were separated out for readability's sake.
- *
- * - Ted Ts'o (tytso@mit.edu), 7-Mar-93
- * -----------------------------------------------------------------------
- */
-
-/*
- * This routine is used by the interrupt handler to schedule
- * processing in the software interrupt portion of the driver.
- */
-static void rs_sched_event(struct dec_serial *info, int event)
-{
- info->event |= 1 << event;
- tasklet_schedule(&info->tlet);
-}
-
-static void receive_chars(struct dec_serial *info)
-{
- struct tty_struct *tty = info->tty;
- unsigned char ch, stat, flag;
-
- while ((read_zsreg(info->zs_channel, R0) & Rx_CH_AV) != 0) {
-
- stat = read_zsreg(info->zs_channel, R1);
- ch = read_zsdata(info->zs_channel);
-
- if (!tty && (!info->hook || !info->hook->rx_char))
- continue;
-
- flag = TTY_NORMAL;
- if (info->tty_break) {
- info->tty_break = 0;
- flag = TTY_BREAK;
- if (info->flags & ZILOG_SAK)
- do_SAK(tty);
- /* Ignore the null char got when BREAK is removed. */
- if (ch == 0)
- continue;
- } else {
- if (stat & Rx_OVR) {
- flag = TTY_OVERRUN;
- } else if (stat & FRM_ERR) {
- flag = TTY_FRAME;
- } else if (stat & PAR_ERR) {
- flag = TTY_PARITY;
- }
- if (flag != TTY_NORMAL)
- /* reset the error indication */
- write_zsreg(info->zs_channel, R0, ERR_RES);
- }
-
-#if defined(CONFIG_SERIAL_DEC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) && \
- !defined(MODULE)
- if (break_pressed && info->line == zs_console.index) {
- /* Ignore the null char got when BREAK is removed. */
- if (ch == 0)
- continue;
- if (time_before(jiffies, break_pressed + HZ * 5)) {
- handle_sysrq(ch, NULL);
- break_pressed = 0;
- continue;
- }
- break_pressed = 0;
- }
-#endif
-
- if (info->hook && info->hook->rx_char) {
- (*info->hook->rx_char)(ch, flag);
- return;
- }
-
- tty_insert_flip_char(tty, ch, flag);
- }
- if (tty)
- tty_flip_buffer_push(tty);
-}
-
-static void transmit_chars(struct dec_serial *info)
-{
- if ((read_zsreg(info->zs_channel, R0) & Tx_BUF_EMP) == 0)
- return;
- info->tx_active = 0;
-
- if (info->x_char) {
- /* Send next char */
- write_zsdata(info->zs_channel, info->x_char);
- info->x_char = 0;
- info->tx_active = 1;
- return;
- }
-
- if ((info->xmit_cnt <= 0) || (info->tty && info->tty->stopped)
- || info->tx_stopped) {
- write_zsreg(info->zs_channel, R0, RES_Tx_P);
- return;
- }
- /* Send char */
- write_zsdata(info->zs_channel, info->xmit_buf[info->xmit_tail++]);
- info->xmit_tail = info->xmit_tail & (SERIAL_XMIT_SIZE-1);
- info->xmit_cnt--;
- info->tx_active = 1;
-
- if (info->xmit_cnt < WAKEUP_CHARS)
- rs_sched_event(info, RS_EVENT_WRITE_WAKEUP);
-}
-
-static void status_handle(struct dec_serial *info)
-{
- unsigned char stat;
-
- /* Get status from Read Register 0 */
- stat = read_zsreg(info->zs_channel, R0);
-
- if ((stat & BRK_ABRT) && !(info->read_reg_zero & BRK_ABRT)) {
-#if defined(CONFIG_SERIAL_DEC_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) && \
- !defined(MODULE)
- if (info->line == zs_console.index) {
- if (!break_pressed)
- break_pressed = jiffies;
- } else
-#endif
- info->tty_break = 1;
- }
-
- if (info->zs_channel != info->zs_chan_a) {
-
- /* Check for DCD transitions */
- if (info->tty && !C_CLOCAL(info->tty) &&
- ((stat ^ info->read_reg_zero) & DCD) != 0 ) {
- if (stat & DCD) {
- wake_up_interruptible(&info->open_wait);
- } else {
- tty_hangup(info->tty);
- }
- }
-
- /* Check for CTS transitions */
- if (info->tty && C_CRTSCTS(info->tty)) {
- if ((stat & CTS) != 0) {
- if (info->tx_stopped) {
- info->tx_stopped = 0;
- if (!info->tx_active)
- transmit_chars(info);
- }
- } else {
- info->tx_stopped = 1;
- }
- }
-
- }
-
- /* Clear status condition... */
- write_zsreg(info->zs_channel, R0, RES_EXT_INT);
- info->read_reg_zero = stat;
-}
-
-/*
- * This is the serial driver's generic interrupt routine
- */
-static irqreturn_t rs_interrupt(int irq, void *dev_id)
-{
- struct dec_serial *info = (struct dec_serial *) dev_id;
- irqreturn_t status = IRQ_NONE;
- unsigned char zs_intreg;
- int shift;
-
- /* NOTE: The read register 3, which holds the irq status,
- * does so for both channels on each chip. Although
- * the status value itself must be read from the A
- * channel and is only valid when read from channel A.
- * Yes... broken hardware...
- */
-#define CHAN_IRQMASK (CHBRxIP | CHBTxIP | CHBEXT)
-
- if (info->zs_chan_a == info->zs_channel)
- shift = 3; /* Channel A */
- else
- shift = 0; /* Channel B */
-
- for (;;) {
- zs_intreg = read_zsreg(info->zs_chan_a, R3) >> shift;
- if ((zs_intreg & CHAN_IRQMASK) == 0)
- break;
-
- status = IRQ_HANDLED;
-
- if (zs_intreg & CHBRxIP) {
- receive_chars(info);
- }
- if (zs_intreg & CHBTxIP) {
- transmit_chars(info);
- }
- if (zs_intreg & CHBEXT) {
- status_handle(info);
- }
- }
-
- /* Why do we need this ? */
- write_zsreg(info->zs_channel, 0, RES_H_IUS);
-
- return status;
-}
-
-#ifdef ZS_DEBUG_REGS
-void zs_dump (void) {
- int i, j;
- for (i = 0; i < zs_channels_found; i++) {
- struct dec_zschannel *ch = &zs_channels[i];
- if ((long)ch->control == UNI_IO_BASE+UNI_SCC1A_CTRL) {
- for (j = 0; j < 15; j++) {
- printk("W%d = 0x%x\t",
- j, (int)ch->curregs[j]);
- }
- for (j = 0; j < 15; j++) {
- printk("R%d = 0x%x\t",
- j, (int)read_zsreg(ch,j));
- }
- printk("\n\n");
- }
- }
-}
-#endif
-
-/*
- * -------------------------------------------------------------------
- * Here ends the serial interrupt routines.
- * -------------------------------------------------------------------
- */
-
-/*
- * ------------------------------------------------------------
- * rs_stop() and rs_start()
- *
- * This routines are called before setting or resetting tty->stopped.
- * ------------------------------------------------------------
- */
-static void rs_stop(struct tty_struct *tty)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
- unsigned long flags;
-
- if (serial_paranoia_check(info, tty->name, "rs_stop"))
- return;
-
-#if 1
- spin_lock_irqsave(&zs_lock, flags);
- if (info->zs_channel->curregs[5] & TxENAB) {
- info->zs_channel->curregs[5] &= ~TxENAB;
- write_zsreg(info->zs_channel, 5, info->zs_channel->curregs[5]);
- }
- spin_unlock_irqrestore(&zs_lock, flags);
-#endif
-}
-
-static void rs_start(struct tty_struct *tty)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
- unsigned long flags;
-
- if (serial_paranoia_check(info, tty->name, "rs_start"))
- return;
-
- spin_lock_irqsave(&zs_lock, flags);
-#if 1
- if (info->xmit_cnt && info->xmit_buf && !(info->zs_channel->curregs[5] & TxENAB)) {
- info->zs_channel->curregs[5] |= TxENAB;
- write_zsreg(info->zs_channel, 5, info->zs_channel->curregs[5]);
- }
-#else
- if (info->xmit_cnt && info->xmit_buf && !info->tx_active) {
- transmit_chars(info);
- }
-#endif
- spin_unlock_irqrestore(&zs_lock, flags);
-}
-
-/*
- * This routine is used to handle the "bottom half" processing for the
- * serial driver, known also the "software interrupt" processing.
- * This processing is done at the kernel interrupt level, after the
- * rs_interrupt() has returned, BUT WITH INTERRUPTS TURNED ON. This
- * is where time-consuming activities which can not be done in the
- * interrupt driver proper are done; the interrupt driver schedules
- * them using rs_sched_event(), and they get done here.
- */
-
-static void do_softint(unsigned long private_)
-{
- struct dec_serial *info = (struct dec_serial *) private_;
- struct tty_struct *tty;
-
- tty = info->tty;
- if (!tty)
- return;
-
- if (test_and_clear_bit(RS_EVENT_WRITE_WAKEUP, &info->event))
- tty_wakeup(tty);
-}
-
-static int zs_startup(struct dec_serial * info)
-{
- unsigned long flags;
-
- if (info->flags & ZILOG_INITIALIZED)
- return 0;
-
- if (!info->xmit_buf) {
- info->xmit_buf = (unsigned char *) get_zeroed_page(GFP_KERNEL);
- if (!info->xmit_buf)
- return -ENOMEM;
- }
-
- spin_lock_irqsave(&zs_lock, flags);
-
-#ifdef SERIAL_DEBUG_OPEN
- printk("starting up ttyS%d (irq %d)...", info->line, info->irq);
-#endif
-
- /*
- * Clear the receive FIFO.
- */
- ZS_CLEARFIFO(info->zs_channel);
- info->xmit_fifo_size = 1;
-
- /*
- * Clear the interrupt registers.
- */
- write_zsreg(info->zs_channel, R0, ERR_RES);
- write_zsreg(info->zs_channel, R0, RES_H_IUS);
-
- /*
- * Set the speed of the serial port
- */
- change_speed(info);
-
- /*
- * Turn on RTS and DTR.
- */
- zs_rtsdtr(info, RTS | DTR, 1);
-
- /*
- * Finally, enable sequencing and interrupts
- */
- info->zs_channel->curregs[R1] &= ~RxINT_MASK;
- info->zs_channel->curregs[R1] |= (RxINT_ALL | TxINT_ENAB |
- EXT_INT_ENAB);
- info->zs_channel->curregs[R3] |= RxENABLE;
- info->zs_channel->curregs[R5] |= TxENAB;
- info->zs_channel->curregs[R15] |= (DCDIE | CTSIE | TxUIE | BRKIE);
- write_zsreg(info->zs_channel, R1, info->zs_channel->curregs[R1]);
- write_zsreg(info->zs_channel, R3, info->zs_channel->curregs[R3]);
- write_zsreg(info->zs_channel, R5, info->zs_channel->curregs[R5]);
- write_zsreg(info->zs_channel, R15, info->zs_channel->curregs[R15]);
-
- /*
- * And clear the interrupt registers again for luck.
- */
- write_zsreg(info->zs_channel, R0, ERR_RES);
- write_zsreg(info->zs_channel, R0, RES_H_IUS);
-
- /* Save the current value of RR0 */
- info->read_reg_zero = read_zsreg(info->zs_channel, R0);
-
- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
- info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
-
- info->flags |= ZILOG_INITIALIZED;
- spin_unlock_irqrestore(&zs_lock, flags);
- return 0;
-}
-
-/*
- * This routine will shutdown a serial port; interrupts are disabled, and
- * DTR is dropped if the hangup on close termio flag is on.
- */
-static void shutdown(struct dec_serial * info)
-{
- unsigned long flags;
-
- if (!(info->flags & ZILOG_INITIALIZED))
- return;
-
-#ifdef SERIAL_DEBUG_OPEN
- printk("Shutting down serial port %d (irq %d)....", info->line,
- info->irq);
-#endif
-
- spin_lock_irqsave(&zs_lock, flags);
-
- if (info->xmit_buf) {
- free_page((unsigned long) info->xmit_buf);
- info->xmit_buf = 0;
- }
-
- info->zs_channel->curregs[1] = 0;
- write_zsreg(info->zs_channel, 1, info->zs_channel->curregs[1]); /* no interrupts */
-
- info->zs_channel->curregs[3] &= ~RxENABLE;
- write_zsreg(info->zs_channel, 3, info->zs_channel->curregs[3]);
-
- info->zs_channel->curregs[5] &= ~TxENAB;
- write_zsreg(info->zs_channel, 5, info->zs_channel->curregs[5]);
- if (!info->tty || C_HUPCL(info->tty)) {
- zs_rtsdtr(info, RTS | DTR, 0);
- }
-
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
-
- info->flags &= ~ZILOG_INITIALIZED;
- spin_unlock_irqrestore(&zs_lock, flags);
-}
-
-/*
- * This routine is called to set the UART divisor registers to match
- * the specified baud rate for a serial port.
- */
-static void change_speed(struct dec_serial *info)
-{
- unsigned cflag;
- int i;
- int brg, bits;
- unsigned long flags;
-
- if (!info->hook) {
- if (!info->tty || !info->tty->termios)
- return;
- cflag = info->tty->termios->c_cflag;
- if (!info->port)
- return;
- } else {
- cflag = info->hook->cflags;
- }
-
- i = cflag & CBAUD;
- if (i & CBAUDEX) {
- i &= ~CBAUDEX;
- if (i < 1 || i > 2) {
- if (!info->hook)
- info->tty->termios->c_cflag &= ~CBAUDEX;
- else
- info->hook->cflags &= ~CBAUDEX;
- } else
- i += 15;
- }
-
- spin_lock_irqsave(&zs_lock, flags);
- info->zs_baud = baud_table[i];
- if (info->zs_baud) {
- brg = BPS_TO_BRG(info->zs_baud, zs_parms->clock/info->clk_divisor);
- info->zs_channel->curregs[12] = (brg & 255);
- info->zs_channel->curregs[13] = ((brg >> 8) & 255);
- zs_rtsdtr(info, DTR, 1);
- } else {
- zs_rtsdtr(info, RTS | DTR, 0);
- return;
- }
-
- /* byte size and parity */
- info->zs_channel->curregs[3] &= ~RxNBITS_MASK;
- info->zs_channel->curregs[5] &= ~TxNBITS_MASK;
- switch (cflag & CSIZE) {
- case CS5:
- bits = 7;
- info->zs_channel->curregs[3] |= Rx5;
- info->zs_channel->curregs[5] |= Tx5;
- break;
- case CS6:
- bits = 8;
- info->zs_channel->curregs[3] |= Rx6;
- info->zs_channel->curregs[5] |= Tx6;
- break;
- case CS7:
- bits = 9;
- info->zs_channel->curregs[3] |= Rx7;
- info->zs_channel->curregs[5] |= Tx7;
- break;
- case CS8:
- default: /* defaults to 8 bits */
- bits = 10;
- info->zs_channel->curregs[3] |= Rx8;
- info->zs_channel->curregs[5] |= Tx8;
- break;
- }
-
- info->timeout = ((info->xmit_fifo_size*HZ*bits) / info->zs_baud);
- info->timeout += HZ/50; /* Add .02 seconds of slop */
-
- info->zs_channel->curregs[4] &= ~(SB_MASK | PAR_ENA | PAR_EVEN);
- if (cflag & CSTOPB) {
- info->zs_channel->curregs[4] |= SB2;
- } else {
- info->zs_channel->curregs[4] |= SB1;
- }
- if (cflag & PARENB) {
- info->zs_channel->curregs[4] |= PAR_ENA;
- }
- if (!(cflag & PARODD)) {
- info->zs_channel->curregs[4] |= PAR_EVEN;
- }
-
- if (!(cflag & CLOCAL)) {
- if (!(info->zs_channel->curregs[15] & DCDIE))
- info->read_reg_zero = read_zsreg(info->zs_channel, 0);
- info->zs_channel->curregs[15] |= DCDIE;
- } else
- info->zs_channel->curregs[15] &= ~DCDIE;
- if (cflag & CRTSCTS) {
- info->zs_channel->curregs[15] |= CTSIE;
- if ((read_zsreg(info->zs_channel, 0) & CTS) == 0)
- info->tx_stopped = 1;
- } else {
- info->zs_channel->curregs[15] &= ~CTSIE;
- info->tx_stopped = 0;
- }
-
- /* Load up the new values */
- load_zsregs(info->zs_channel, info->zs_channel->curregs);
-
- spin_unlock_irqrestore(&zs_lock, flags);
-}
-
-static void rs_flush_chars(struct tty_struct *tty)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
- unsigned long flags;
-
- if (serial_paranoia_check(info, tty->name, "rs_flush_chars"))
- return;
-
- if (info->xmit_cnt <= 0 || tty->stopped || info->tx_stopped ||
- !info->xmit_buf)
- return;
-
- /* Enable transmitter */
- spin_lock_irqsave(&zs_lock, flags);
- transmit_chars(info);
- spin_unlock_irqrestore(&zs_lock, flags);
-}
-
-static int rs_write(struct tty_struct * tty,
- const unsigned char *buf, int count)
-{
- int c, total = 0;
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
- unsigned long flags;
-
- if (serial_paranoia_check(info, tty->name, "rs_write"))
- return 0;
-
- if (!tty || !info->xmit_buf)
- return 0;
-
- while (1) {
- spin_lock_irqsave(&zs_lock, flags);
- c = min(count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
- SERIAL_XMIT_SIZE - info->xmit_head));
- if (c <= 0)
- break;
-
- memcpy(info->xmit_buf + info->xmit_head, buf, c);
- info->xmit_head = (info->xmit_head + c) & (SERIAL_XMIT_SIZE-1);
- info->xmit_cnt += c;
- spin_unlock_irqrestore(&zs_lock, flags);
- buf += c;
- count -= c;
- total += c;
- }
-
- if (info->xmit_cnt && !tty->stopped && !info->tx_stopped
- && !info->tx_active)
- transmit_chars(info);
- spin_unlock_irqrestore(&zs_lock, flags);
- return total;
-}
-
-static int rs_write_room(struct tty_struct *tty)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
- int ret;
-
- if (serial_paranoia_check(info, tty->name, "rs_write_room"))
- return 0;
- ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
- if (ret < 0)
- ret = 0;
- return ret;
-}
-
-static int rs_chars_in_buffer(struct tty_struct *tty)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
-
- if (serial_paranoia_check(info, tty->name, "rs_chars_in_buffer"))
- return 0;
- return info->xmit_cnt;
-}
-
-static void rs_flush_buffer(struct tty_struct *tty)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
-
- if (serial_paranoia_check(info, tty->name, "rs_flush_buffer"))
- return;
- spin_lock_irq(&zs_lock);
- info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
- spin_unlock_irq(&zs_lock);
- tty_wakeup(tty);
-}
-
-/*
- * ------------------------------------------------------------
- * rs_throttle()
- *
- * This routine is called by the upper-layer tty layer to signal that
- * incoming characters should be throttled.
- * ------------------------------------------------------------
- */
-static void rs_throttle(struct tty_struct * tty)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
- unsigned long flags;
-
-#ifdef SERIAL_DEBUG_THROTTLE
- char buf[64];
-
- printk("throttle %s: %d....\n", _tty_name(tty, buf),
- tty->ldisc.chars_in_buffer(tty));
-#endif
-
- if (serial_paranoia_check(info, tty->name, "rs_throttle"))
- return;
-
- if (I_IXOFF(tty)) {
- spin_lock_irqsave(&zs_lock, flags);
- info->x_char = STOP_CHAR(tty);
- if (!info->tx_active)
- transmit_chars(info);
- spin_unlock_irqrestore(&zs_lock, flags);
- }
-
- if (C_CRTSCTS(tty)) {
- zs_rtsdtr(info, RTS, 0);
- }
-}
-
-static void rs_unthrottle(struct tty_struct * tty)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
- unsigned long flags;
-
-#ifdef SERIAL_DEBUG_THROTTLE
- char buf[64];
-
- printk("unthrottle %s: %d....\n", _tty_name(tty, buf),
- tty->ldisc.chars_in_buffer(tty));
-#endif
-
- if (serial_paranoia_check(info, tty->name, "rs_unthrottle"))
- return;
-
- if (I_IXOFF(tty)) {
- spin_lock_irqsave(&zs_lock, flags);
- if (info->x_char)
- info->x_char = 0;
- else {
- info->x_char = START_CHAR(tty);
- if (!info->tx_active)
- transmit_chars(info);
- }
- spin_unlock_irqrestore(&zs_lock, flags);
- }
-
- if (C_CRTSCTS(tty)) {
- zs_rtsdtr(info, RTS, 1);
- }
-}
-
-/*
- * ------------------------------------------------------------
- * rs_ioctl() and friends
- * ------------------------------------------------------------
- */
-
-static int get_serial_info(struct dec_serial * info,
- struct serial_struct * retinfo)
-{
- struct serial_struct tmp;
-
- if (!retinfo)
- return -EFAULT;
- memset(&tmp, 0, sizeof(tmp));
- tmp.type = info->type;
- tmp.line = info->line;
- tmp.port = info->port;
- tmp.irq = info->irq;
- tmp.flags = info->flags;
- tmp.baud_base = info->baud_base;
- tmp.close_delay = info->close_delay;
- tmp.closing_wait = info->closing_wait;
- tmp.custom_divisor = info->custom_divisor;
- return copy_to_user(retinfo,&tmp,sizeof(*retinfo)) ? -EFAULT : 0;
-}
-
-static int set_serial_info(struct dec_serial * info,
- struct serial_struct * new_info)
-{
- struct serial_struct new_serial;
- struct dec_serial old_info;
- int retval = 0;
-
- if (!new_info)
- return -EFAULT;
- copy_from_user(&new_serial,new_info,sizeof(new_serial));
- old_info = *info;
-
- if (!capable(CAP_SYS_ADMIN)) {
- if ((new_serial.baud_base != info->baud_base) ||
- (new_serial.type != info->type) ||
- (new_serial.close_delay != info->close_delay) ||
- ((new_serial.flags & ~ZILOG_USR_MASK) !=
- (info->flags & ~ZILOG_USR_MASK)))
- return -EPERM;
- info->flags = ((info->flags & ~ZILOG_USR_MASK) |
- (new_serial.flags & ZILOG_USR_MASK));
- info->custom_divisor = new_serial.custom_divisor;
- goto check_and_exit;
- }
-
- if (info->count > 1)
- return -EBUSY;
-
- /*
- * OK, past this point, all the error checking has been done.
- * At this point, we start making changes.....
- */
-
- info->baud_base = new_serial.baud_base;
- info->flags = ((info->flags & ~ZILOG_FLAGS) |
- (new_serial.flags & ZILOG_FLAGS));
- info->type = new_serial.type;
- info->close_delay = new_serial.close_delay;
- info->closing_wait = new_serial.closing_wait;
-
-check_and_exit:
- retval = zs_startup(info);
- return retval;
-}
-
-/*
- * get_lsr_info - get line status register info
- *
- * Purpose: Let user call ioctl() to get info when the UART physically
- * is emptied. On bus types like RS485, the transmitter must
- * release the bus after transmitting. This must be done when
- * the transmit shift register is empty, not be done when the
- * transmit holding register is empty. This functionality
- * allows an RS485 driver to be written in user space.
- */
-static int get_lsr_info(struct dec_serial * info, unsigned int *value)
-{
- unsigned char status;
-
- spin_lock(&zs_lock);
- status = read_zsreg(info->zs_channel, 0);
- spin_unlock_irq(&zs_lock);
- put_user(status,value);
- return 0;
-}
-
-static int rs_tiocmget(struct tty_struct *tty, struct file *file)
-{
- struct dec_serial * info = (struct dec_serial *)tty->driver_data;
- unsigned char control, status_a, status_b;
- unsigned int result;
-
- if (info->hook)
- return -ENODEV;
-
- if (serial_paranoia_check(info, tty->name, __FUNCTION__))
- return -ENODEV;
-
- if (tty->flags & (1 << TTY_IO_ERROR))
- return -EIO;
-
- if (info->zs_channel == info->zs_chan_a)
- result = 0;
- else {
- spin_lock(&zs_lock);
- control = info->zs_chan_a->curregs[5];
- status_a = read_zsreg(info->zs_chan_a, 0);
- status_b = read_zsreg(info->zs_channel, 0);
- spin_unlock_irq(&zs_lock);
- result = ((control & RTS) ? TIOCM_RTS: 0)
- | ((control & DTR) ? TIOCM_DTR: 0)
- | ((status_b & DCD) ? TIOCM_CAR: 0)
- | ((status_a & DCD) ? TIOCM_RNG: 0)
- | ((status_a & SYNC_HUNT) ? TIOCM_DSR: 0)
- | ((status_b & CTS) ? TIOCM_CTS: 0);
- }
- return result;
-}
-
-static int rs_tiocmset(struct tty_struct *tty, struct file *file,
- unsigned int set, unsigned int clear)
-{
- struct dec_serial * info = (struct dec_serial *)tty->driver_data;
-
- if (info->hook)
- return -ENODEV;
-
- if (serial_paranoia_check(info, tty->name, __FUNCTION__))
- return -ENODEV;
-
- if (tty->flags & (1 << TTY_IO_ERROR))
- return -EIO;
-
- if (info->zs_channel == info->zs_chan_a)
- return 0;
-
- spin_lock(&zs_lock);
- if (set & TIOCM_RTS)
- info->zs_chan_a->curregs[5] |= RTS;
- if (set & TIOCM_DTR)
- info->zs_chan_a->curregs[5] |= DTR;
- if (clear & TIOCM_RTS)
- info->zs_chan_a->curregs[5] &= ~RTS;
- if (clear & TIOCM_DTR)
- info->zs_chan_a->curregs[5] &= ~DTR;
- write_zsreg(info->zs_chan_a, 5, info->zs_chan_a->curregs[5]);
- spin_unlock_irq(&zs_lock);
- return 0;
-}
-
-/*
- * rs_break - turn transmit break condition on/off
- */
-static void rs_break(struct tty_struct *tty, int break_state)
-{
- struct dec_serial *info = (struct dec_serial *) tty->driver_data;
- unsigned long flags;
-
- if (serial_paranoia_check(info, tty->name, "rs_break"))
- return;
- if (!info->port)
- return;
-
- spin_lock_irqsave(&zs_lock, flags);
- if (break_state == -1)
- info->zs_channel->curregs[5] |= SND_BRK;
- else
- info->zs_channel->curregs[5] &= ~SND_BRK;
- write_zsreg(info->zs_channel, 5, info->zs_channel->curregs[5]);
- spin_unlock_irqrestore(&zs_lock, flags);
-}
-
-static int rs_ioctl(struct tty_struct *tty, struct file * file,
- unsigned int cmd, unsigned long arg)
-{
- struct dec_serial * info = (struct dec_serial *)tty->driver_data;
-
- if (info->hook)
- return -ENODEV;
-
- if (serial_paranoia_check(info, tty->name, "rs_ioctl"))
- return -ENODEV;
-
- if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
- (cmd != TIOCSERCONFIG) && (cmd != TIOCSERGWILD) &&
- (cmd != TIOCSERSWILD) && (cmd != TIOCSERGSTRUCT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
- return -EIO;
- }
-
- switch (cmd) {
- case TIOCGSERIAL:
- if (!access_ok(VERIFY_WRITE, (void *)arg,
- sizeof(struct serial_struct)))
- return -EFAULT;
- return get_serial_info(info, (struct serial_struct *)arg);
-
- case TIOCSSERIAL:
- return set_serial_info(info, (struct serial_struct *)arg);
-
- case TIOCSERGETLSR: /* Get line status register */
- if (!access_ok(VERIFY_WRITE, (void *)arg,
- sizeof(unsigned int)))
- return -EFAULT;
- return get_lsr_info(info, (unsigned int *)arg);
-
- case TIOCSERGSTRUCT:
- if (!access_ok(VERIFY_WRITE, (void *)arg,
- sizeof(struct dec_serial)))
- return -EFAULT;
- copy_from_user((struct dec_serial *)arg, info,
- sizeof(struct dec_serial));
- return 0;
-
- default:
- return -ENOIOCTLCMD;
- }
- return 0;
-}
-
-static void rs_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
-{
- struct dec_serial *info = (struct dec_serial *)tty->driver_data;
- int was_stopped;
-
- if (tty->termios->c_cflag == old_termios->c_cflag)
- return;
- was_stopped = info->tx_stopped;
-
- change_speed(info);
-
- if (was_stopped && !info->tx_stopped)
- rs_start(tty);
-}
-
-/*
- * ------------------------------------------------------------
- * rs_close()
- *
- * This routine is called when the serial port gets closed.
- * Wait for the last remaining data to be sent.
- * ------------------------------------------------------------
- */
-static void rs_close(struct tty_struct *tty, struct file * filp)
-{
- struct dec_serial * info = (struct dec_serial *)tty->driver_data;
- unsigned long flags;
-
- if (!info || serial_paranoia_check(info, tty->name, "rs_close"))
- return;
-
- spin_lock_irqsave(&zs_lock, flags);
-
- if (tty_hung_up_p(filp)) {
- spin_unlock_irqrestore(&zs_lock, flags);
- return;
- }
-
-#ifdef SERIAL_DEBUG_OPEN
- printk("rs_close ttyS%d, count = %d\n", info->line, info->count);
-#endif
- if ((tty->count == 1) && (info->count != 1)) {
- /*
- * Uh, oh. tty->count is 1, which means that the tty
- * structure will be freed. Info->count should always
- * be one in these conditions. If it's greater than
- * one, we've got real problems, since it means the
- * serial port won't be shutdown.
- */
- printk("rs_close: bad serial port count; tty->count is 1, "
- "info->count is %d\n", info->count);
- info->count = 1;
- }
- if (--info->count < 0) {
- printk("rs_close: bad serial port count for ttyS%d: %d\n",
- info->line, info->count);
- info->count = 0;
- }
- if (info->count) {
- spin_unlock_irqrestore(&zs_lock, flags);
- return;
- }
- info->flags |= ZILOG_CLOSING;
- /*
- * Now we wait for the transmit buffer to clear; and we notify
- * the line discipline to only process XON/XOFF characters.
- */
- tty->closing = 1;
- if (info->closing_wait != ZILOG_CLOSING_WAIT_NONE)
- tty_wait_until_sent(tty, info->closing_wait);
- /*
- * At this point we stop accepting input. To do this, we
- * disable the receiver and receive interrupts.
- */
- info->zs_channel->curregs[3] &= ~RxENABLE;
- write_zsreg(info->zs_channel, 3, info->zs_channel->curregs[3]);
- info->zs_channel->curregs[1] = 0; /* disable any rx ints */
- write_zsreg(info->zs_channel, 1, info->zs_channel->curregs[1]);
- ZS_CLEARFIFO(info->zs_channel);
- if (info->flags & ZILOG_INITIALIZED) {
- /*
- * Before we drop DTR, make sure the SCC transmitter
- * has completely drained.
- */
- rs_wait_until_sent(tty, info->timeout);
- }
-
- shutdown(info);
- if (tty->driver->flush_buffer)
- tty->driver->flush_buffer(tty);
- tty_ldisc_flush(tty);
- tty->closing = 0;
- info->event = 0;
- info->tty = 0;
- if (info->blocked_open) {
- if (info->close_delay) {
- msleep_interruptible(jiffies_to_msecs(info->close_delay));
- }
- wake_up_interruptible(&info->open_wait);
- }
- info->flags &= ~(ZILOG_NORMAL_ACTIVE|ZILOG_CLOSING);
- wake_up_interruptible(&info->close_wait);
- spin_unlock_irqrestore(&zs_lock, flags);
-}
-
-/*
- * rs_wait_until_sent() --- wait until the transmitter is empty
- */
-static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
-{
- struct dec_serial *info = (struct dec_serial *) tty->driver_data;
- unsigned long orig_jiffies;
- int char_time;
-
- if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent"))
- return;
-
- orig_jiffies = jiffies;
- /*
- * Set the check interval to be 1/5 of the estimated time to
- * send a single character, and make it at least 1. The check
- * interval should also be less than the timeout.
- */
- char_time = (info->timeout - HZ/50) / info->xmit_fifo_size;
- char_time = char_time / 5;
- if (char_time == 0)
- char_time = 1;
- if (timeout)
- char_time = min(char_time, timeout);
- while ((read_zsreg(info->zs_channel, 1) & Tx_BUF_EMP) == 0) {
- msleep_interruptible(jiffies_to_msecs(char_time));
- if (signal_pending(current))
- break;
- if (timeout && time_after(jiffies, orig_jiffies + timeout))
- break;
- }
- current->state = TASK_RUNNING;
-}
-
-/*
- * rs_hangup() --- called by tty_hangup() when a hangup is signaled.
- */
-static void rs_hangup(struct tty_struct *tty)
-{
- struct dec_serial * info = (struct dec_serial *)tty->driver_data;
-
- if (serial_paranoia_check(info, tty->name, "rs_hangup"))
- return;
-
- rs_flush_buffer(tty);
- shutdown(info);
- info->event = 0;
- info->count = 0;
- info->flags &= ~ZILOG_NORMAL_ACTIVE;
- info->tty = 0;
- wake_up_interruptible(&info->open_wait);
-}
-
-/*
- * ------------------------------------------------------------
- * rs_open() and friends
- * ------------------------------------------------------------
- */
-static int block_til_ready(struct tty_struct *tty, struct file * filp,
- struct dec_serial *info)
-{
- DECLARE_WAITQUEUE(wait, current);
- int retval;
- int do_clocal = 0;
-
- /*
- * If the device is in the middle of being closed, then block
- * until it's done, and then try again.
- */
- if (info->flags & ZILOG_CLOSING) {
- interruptible_sleep_on(&info->close_wait);
-#ifdef SERIAL_DO_RESTART
- return ((info->flags & ZILOG_HUP_NOTIFY) ?
- -EAGAIN : -ERESTARTSYS);
-#else
- return -EAGAIN;
-#endif
- }
-
- /*
- * If non-blocking mode is set, or the port is not enabled,
- * then make the check up front and then exit.
- */
- if ((filp->f_flags & O_NONBLOCK) ||
- (tty->flags & (1 << TTY_IO_ERROR))) {
- info->flags |= ZILOG_NORMAL_ACTIVE;
- return 0;
- }
-
- if (tty->termios->c_cflag & CLOCAL)
- do_clocal = 1;
-
- /*
- * Block waiting for the carrier detect and the line to become
- * free (i.e., not in use by the callout). While we are in
- * this loop, info->count is dropped by one, so that
- * rs_close() knows when to free things. We restore it upon
- * exit, either normal or abnormal.
- */
- retval = 0;
- add_wait_queue(&info->open_wait, &wait);
-#ifdef SERIAL_DEBUG_OPEN
- printk("block_til_ready before block: ttyS%d, count = %d\n",
- info->line, info->count);
-#endif
- spin_lock(&zs_lock);
- if (!tty_hung_up_p(filp))
- info->count--;
- spin_unlock_irq(&zs_lock);
- info->blocked_open++;
- while (1) {
- spin_lock(&zs_lock);
- if (tty->termios->c_cflag & CBAUD)
- zs_rtsdtr(info, RTS | DTR, 1);
- spin_unlock_irq(&zs_lock);
- set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) ||
- !(info->flags & ZILOG_INITIALIZED)) {
-#ifdef SERIAL_DO_RESTART
- if (info->flags & ZILOG_HUP_NOTIFY)
- retval = -EAGAIN;
- else
- retval = -ERESTARTSYS;
-#else
- retval = -EAGAIN;
-#endif
- break;
- }
- if (!(info->flags & ZILOG_CLOSING) &&
- (do_clocal || (read_zsreg(info->zs_channel, 0) & DCD)))
- break;
- if (signal_pending(current)) {
- retval = -ERESTARTSYS;
- break;
- }
-#ifdef SERIAL_DEBUG_OPEN
- printk("block_til_ready blocking: ttyS%d, count = %d\n",
- info->line, info->count);
-#endif
- schedule();
- }
- current->state = TASK_RUNNING;
- remove_wait_queue(&info->open_wait, &wait);
- if (!tty_hung_up_p(filp))
- info->count++;
- info->blocked_open--;
-#ifdef SERIAL_DEBUG_OPEN
- printk("block_til_ready after blocking: ttyS%d, count = %d\n",
- info->line, info->count);
-#endif
- if (retval)
- return retval;
- info->flags |= ZILOG_NORMAL_ACTIVE;
- return 0;
-}
-
-/*
- * This routine is called whenever a serial port is opened. It
- * enables interrupts for a serial port, linking in its ZILOG structure into
- * the IRQ chain. It also performs the serial-specific
- * initialization for the tty structure.
- */
-static int rs_open(struct tty_struct *tty, struct file * filp)
-{
- struct dec_serial *info;
- int retval, line;
-
- line = tty->index;
- if ((line < 0) || (line >= zs_channels_found))
- return -ENODEV;
- info = zs_soft + line;
-
- if (info->hook)
- return -ENODEV;
-
- if (serial_paranoia_check(info, tty->name, "rs_open"))
- return -ENODEV;
-#ifdef SERIAL_DEBUG_OPEN
- printk("rs_open %s, count = %d\n", tty->name, info->count);
-#endif
-
- info->count++;
- tty->driver_data = info;
- info->tty = tty;
-
- /*
- * If the port is the middle of closing, bail out now
- */
- if (tty_hung_up_p(filp) ||
- (info->flags & ZILOG_CLOSING)) {
- if (info->flags & ZILOG_CLOSING)
- interruptible_sleep_on(&info->close_wait);
-#ifdef SERIAL_DO_RESTART
- return ((info->flags & ZILOG_HUP_NOTIFY) ?
- -EAGAIN : -ERESTARTSYS);
-#else
- return -EAGAIN;
-#endif
- }
-
- /*
- * Start up serial port
- */
- retval = zs_startup(info);
- if (retval)
- return retval;
-
- retval = block_til_ready(tty, filp, info);
- if (retval) {
-#ifdef SERIAL_DEBUG_OPEN
- printk("rs_open returning after block_til_ready with %d\n",
- retval);
-#endif
- return retval;
- }
-
-#ifdef CONFIG_SERIAL_DEC_CONSOLE
- if (zs_console.cflag && zs_console.index == line) {
- tty->termios->c_cflag = zs_console.cflag;
- zs_console.cflag = 0;
- change_speed(info);
- }
-#endif
-
-#ifdef SERIAL_DEBUG_OPEN
- printk("rs_open %s successful...", tty->name);
-#endif
-/* tty->low_latency = 1; */
- return 0;
-}
-
-/* Finally, routines used to initialize the serial driver. */
-
-static void __init show_serial_version(void)
-{
- printk("DECstation Z8530 serial driver version 0.09\n");
-}
-
-/* Initialize Z8530s zs_channels
- */
-
-static void __init probe_sccs(void)
-{
- struct dec_serial **pp;
- int i, n, n_chips = 0, n_channels, chip, channel;
- unsigned long flags;
-
- /*
- * did we get here by accident?
- */
- if(!BUS_PRESENT) {
- printk("Not on JUNKIO machine, skipping probe_sccs\n");
- return;
- }
-
- switch(mips_machtype) {
-#ifdef CONFIG_MACH_DECSTATION
- case MACH_DS5000_2X0:
- case MACH_DS5900:
- n_chips = 2;
- zs_parms = &ds_parms;
- zs_parms->irq0 = dec_interrupt[DEC_IRQ_SCC0];
- zs_parms->irq1 = dec_interrupt[DEC_IRQ_SCC1];
- break;
- case MACH_DS5000_1XX:
- n_chips = 2;
- zs_parms = &ds_parms;
- zs_parms->irq0 = dec_interrupt[DEC_IRQ_SCC0];
- zs_parms->irq1 = dec_interrupt[DEC_IRQ_SCC1];
- break;
- case MACH_DS5000_XX:
- n_chips = 1;
- zs_parms = &ds_parms;
- zs_parms->irq0 = dec_interrupt[DEC_IRQ_SCC0];
- break;
-#endif
- default:
- panic("zs: unsupported bus");
- }
- if (!zs_parms)
- panic("zs: uninitialized parms");
-
- pp = &zs_chain;
-
- n_channels = 0;
-
- for (chip = 0; chip < n_chips; chip++) {
- for (channel = 0; channel <= 1; channel++) {
- /*
- * The sccs reside on the high byte of the 16 bit IOBUS
- */
- zs_channels[n_channels].control =
- (volatile void *)CKSEG1ADDR(dec_kn_slot_base +
- (0 == chip ? zs_parms->scc0 : zs_parms->scc1) +
- (0 == channel ? zs_parms->channel_a_offset :
- zs_parms->channel_b_offset));
- zs_channels[n_channels].data =
- zs_channels[n_channels].control + 4;
-
-#ifndef CONFIG_SERIAL_DEC_CONSOLE
- /*
- * We're called early and memory managment isn't up, yet.
- * Thus request_region would fail.
- */
- if (!request_region((unsigned long)
- zs_channels[n_channels].control,
- ZS_CHAN_IO_SIZE, "SCC"))
- panic("SCC I/O region is not free");
-#endif
- zs_soft[n_channels].zs_channel = &zs_channels[n_channels];
- /* HACK alert! */
- if (!(chip & 1))
- zs_soft[n_channels].irq = zs_parms->irq0;
- else
- zs_soft[n_channels].irq = zs_parms->irq1;
-
- /*
- * Identification of channel A. Location of channel A
- * inside chip depends on mapping of internal address
- * the chip decodes channels by.
- * CHANNEL_A_NR returns either 0 (in case of
- * DECstations) or 1 (in case of Baget).
- */
- if (CHANNEL_A_NR == channel)
- zs_soft[n_channels].zs_chan_a =
- &zs_channels[n_channels+1-2*CHANNEL_A_NR];
- else
- zs_soft[n_channels].zs_chan_a =
- &zs_channels[n_channels];
-
- *pp = &zs_soft[n_channels];
- pp = &zs_soft[n_channels].zs_next;
- n_channels++;
- }
- }
-
- *pp = 0;
- zs_channels_found = n_channels;
-
- for (n = 0; n < zs_channels_found; n++) {
- for (i = 0; i < 16; i++) {
- zs_soft[n].zs_channel->curregs[i] = zs_init_regs[i];
- }
- }
-
- spin_lock_irqsave(&zs_lock, flags);
- for (n = 0; n < zs_channels_found; n++) {
- if (n % 2 == 0) {
- write_zsreg(zs_soft[n].zs_chan_a, R9, FHWRES);
- udelay(10);
- write_zsreg(zs_soft[n].zs_chan_a, R9, 0);
- }
- load_zsregs(zs_soft[n].zs_channel,
- zs_soft[n].zs_channel->curregs);
- }
- spin_unlock_irqrestore(&zs_lock, flags);
-}
-
-static const struct tty_operations serial_ops = {
- .open = rs_open,
- .close = rs_close,
- .write = rs_write,
- .flush_chars = rs_flush_chars,
- .write_room = rs_write_room,
- .chars_in_buffer = rs_chars_in_buffer,
- .flush_buffer = rs_flush_buffer,
- .ioctl = rs_ioctl,
- .throttle = rs_throttle,
- .unthrottle = rs_unthrottle,
- .set_termios = rs_set_termios,
- .stop = rs_stop,
- .start = rs_start,
- .hangup = rs_hangup,
- .break_ctl = rs_break,
- .wait_until_sent = rs_wait_until_sent,
- .tiocmget = rs_tiocmget,
- .tiocmset = rs_tiocmset,
-};
-
-/* zs_init inits the driver */
-int __init zs_init(void)
-{
- int channel, i;
- struct dec_serial *info;
-
- if(!BUS_PRESENT)
- return -ENODEV;
-
- /* Find out how many Z8530 SCCs we have */
- if (zs_chain == 0)
- probe_sccs();
- serial_driver = alloc_tty_driver(zs_channels_found);
- if (!serial_driver)
- return -ENOMEM;
-
- show_serial_version();
-
- /* Initialize the tty_driver structure */
- /* Not all of this is exactly right for us. */
-
- serial_driver->owner = THIS_MODULE;
- serial_driver->name = "ttyS";
- serial_driver->major = TTY_MAJOR;
- serial_driver->minor_start = 64;
- serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
- serial_driver->subtype = SERIAL_TYPE_NORMAL;
- serial_driver->init_termios = tty_std_termios;
- serial_driver->init_termios.c_cflag =
- B9600 | CS8 | CREAD | HUPCL | CLOCAL;
- serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
- tty_set_operations(serial_driver, &serial_ops);
-
- if (tty_register_driver(serial_driver))
- panic("Couldn't register serial driver");
-
- for (info = zs_chain, i = 0; info; info = info->zs_next, i++) {
-
- /* Needed before interrupts are enabled. */
- info->tty = 0;
- info->x_char = 0;
-
- if (info->hook && info->hook->init_info) {
- (*info->hook->init_info)(info);
- continue;
- }
-
- info->magic = SERIAL_MAGIC;
- info->port = (int) info->zs_channel->control;
- info->line = i;
- info->custom_divisor = 16;
- info->close_delay = 50;
- info->closing_wait = 3000;
- info->event = 0;
- info->count = 0;
- info->blocked_open = 0;
- tasklet_init(&info->tlet, do_softint, (unsigned long)info);
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
- printk("ttyS%02d at 0x%08x (irq = %d) is a Z85C30 SCC\n",
- info->line, info->port, info->irq);
- tty_register_device(serial_driver, info->line, NULL);
-
- }
-
- for (channel = 0; channel < zs_channels_found; ++channel) {
- zs_soft[channel].clk_divisor = 16;
- zs_soft[channel].zs_baud = get_zsbaud(&zs_soft[channel]);
-
- if (request_irq(zs_soft[channel].irq, rs_interrupt, IRQF_SHARED,
- "scc", &zs_soft[channel]))
- printk(KERN_ERR "decserial: can't get irq %d\n",
- zs_soft[channel].irq);
-
- if (zs_soft[channel].hook) {
- zs_startup(&zs_soft[channel]);
- if (zs_soft[channel].hook->init_channel)
- (*zs_soft[channel].hook->init_channel)
- (&zs_soft[channel]);
- }
- }
-
- return 0;
-}
-
-/*
- * polling I/O routines
- */
-static int zs_poll_tx_char(void *handle, unsigned char ch)
-{
- struct dec_serial *info = handle;
- struct dec_zschannel *chan = info->zs_channel;
- int ret;
-
- if(chan) {
- int loops = 10000;
-
- while (loops && !(read_zsreg(chan, 0) & Tx_BUF_EMP))
- loops--;
-
- if (loops) {
- write_zsdata(chan, ch);
- ret = 0;
- } else
- ret = -EAGAIN;
-
- return ret;
- } else
- return -ENODEV;
-}
-
-static int zs_poll_rx_char(void *handle)
-{
- struct dec_serial *info = handle;
- struct dec_zschannel *chan = info->zs_channel;
- int ret;
-
- if(chan) {
- int loops = 10000;
-
- while (loops && !(read_zsreg(chan, 0) & Rx_CH_AV))
- loops--;
-
- if (loops)
- ret = read_zsdata(chan);
- else
- ret = -EAGAIN;
-
- return ret;
- } else
- return -ENODEV;
-}
-
-int register_zs_hook(unsigned int channel, struct dec_serial_hook *hook)
-{
- struct dec_serial *info = &zs_soft[channel];
-
- if (info->hook) {
- printk("%s: line %d has already a hook registered\n",
- __FUNCTION__, channel);
-
- return 0;
- } else {
- hook->poll_rx_char = zs_poll_rx_char;
- hook->poll_tx_char = zs_poll_tx_char;
- info->hook = hook;
-
- return 1;
- }
-}
-
-int unregister_zs_hook(unsigned int channel)
-{
- struct dec_serial *info = &zs_soft[channel];
-
- if (info->hook) {
- info->hook = NULL;
- return 1;
- } else {
- printk("%s: trying to unregister hook on line %d,"
- " but none is registered\n", __FUNCTION__, channel);
- return 0;
- }
-}
-
-/*
- * ------------------------------------------------------------
- * Serial console driver
- * ------------------------------------------------------------
- */
-#ifdef CONFIG_SERIAL_DEC_CONSOLE
-
-
-/*
- * Print a string to the serial port trying not to disturb
- * any possible real use of the port...
- */
-static void serial_console_write(struct console *co, const char *s,
- unsigned count)
-{
- struct dec_serial *info;
- int i;
-
- info = zs_soft + co->index;
-
- for (i = 0; i < count; i++, s++) {
- if(*s == '\n')
- zs_poll_tx_char(info, '\r');
- zs_poll_tx_char(info, *s);
- }
-}
-
-static struct tty_driver *serial_console_device(struct console *c, int *index)
-{
- *index = c->index;
- return serial_driver;
-}
-
-/*
- * Setup initial baud/bits/parity. We do two things here:
- * - construct a cflag setting for the first rs_open()
- * - initialize the serial port
- * Return non-zero if we didn't find a serial port.
- */
-static int __init serial_console_setup(struct console *co, char *options)
-{
- struct dec_serial *info;
- int baud = 9600;
- int bits = 8;
- int parity = 'n';
- int cflag = CREAD | HUPCL | CLOCAL;
- int clk_divisor = 16;
- int brg;
- char *s;
- unsigned long flags;
-
- if(!BUS_PRESENT)
- return -ENODEV;
-
- info = zs_soft + co->index;
-
- if (zs_chain == 0)
- probe_sccs();
-
- info->is_cons = 1;
-
- if (options) {
- baud = simple_strtoul(options, NULL, 10);
- s = options;
- while(*s >= '0' && *s <= '9')
- s++;
- if (*s)
- parity = *s++;
- if (*s)
- bits = *s - '0';
- }
-
- /*
- * Now construct a cflag setting.
- */
- switch(baud) {
- case 1200:
- cflag |= B1200;
- break;
- case 2400:
- cflag |= B2400;
- break;
- case 4800:
- cflag |= B4800;
- break;
- case 19200:
- cflag |= B19200;
- break;
- case 38400:
- cflag |= B38400;
- break;
- case 57600:
- cflag |= B57600;
- break;
- case 115200:
- cflag |= B115200;
- break;
- case 9600:
- default:
- cflag |= B9600;
- /*
- * Set this to a sane value to prevent a divide error.
- */
- baud = 9600;
- break;
- }
- switch(bits) {
- case 7:
- cflag |= CS7;
- break;
- default:
- case 8:
- cflag |= CS8;
- break;
- }
- switch(parity) {
- case 'o': case 'O':
- cflag |= PARODD;
- break;
- case 'e': case 'E':
- cflag |= PARENB;
- break;
- }
- co->cflag = cflag;
-
- spin_lock_irqsave(&zs_lock, flags);
-
- /*
- * Set up the baud rate generator.
- */
- brg = BPS_TO_BRG(baud, zs_parms->clock / clk_divisor);
- info->zs_channel->curregs[R12] = (brg & 255);
- info->zs_channel->curregs[R13] = ((brg >> 8) & 255);
-
- /*
- * Set byte size and parity.
- */
- if (bits == 7) {
- info->zs_channel->curregs[R3] |= Rx7;
- info->zs_channel->curregs[R5] |= Tx7;
- } else {
- info->zs_channel->curregs[R3] |= Rx8;
- info->zs_channel->curregs[R5] |= Tx8;
- }
- if (cflag & PARENB) {
- info->zs_channel->curregs[R4] |= PAR_ENA;
- }
- if (!(cflag & PARODD)) {
- info->zs_channel->curregs[R4] |= PAR_EVEN;
- }
- info->zs_channel->curregs[R4] |= SB1;
-
- /*
- * Turn on RTS and DTR.
- */
- zs_rtsdtr(info, RTS | DTR, 1);
-
- /*
- * Finally, enable sequencing.
- */
- info->zs_channel->curregs[R3] |= RxENABLE;
- info->zs_channel->curregs[R5] |= TxENAB;
-
- /*
- * Clear the interrupt registers.
- */
- write_zsreg(info->zs_channel, R0, ERR_RES);
- write_zsreg(info->zs_channel, R0, RES_H_IUS);
-
- /*
- * Load up the new values.
- */
- load_zsregs(info->zs_channel, info->zs_channel->curregs);
-
- /* Save the current value of RR0 */
- info->read_reg_zero = read_zsreg(info->zs_channel, R0);
-
- zs_soft[co->index].clk_divisor = clk_divisor;
- zs_soft[co->index].zs_baud = get_zsbaud(&zs_soft[co->index]);
-
- spin_unlock_irqrestore(&zs_lock, flags);
-
- return 0;
-}
-
-static struct console zs_console = {
- .name = "ttyS",
- .write = serial_console_write,
- .device = serial_console_device,
- .setup = serial_console_setup,
- .flags = CON_PRINTBUFFER,
- .index = -1,
-};
-
-/*
- * Register console.
- */
-void __init zs_serial_console_init(void)
-{
- register_console(&zs_console);
-}
-#endif /* ifdef CONFIG_SERIAL_DEC_CONSOLE */
-
-#ifdef CONFIG_KGDB
-struct dec_zschannel *zs_kgdbchan;
-static unsigned char scc_inittab[] = {
- 9, 0x80, /* reset A side (CHRA) */
- 13, 0, /* set baud rate divisor */
- 12, 1,
- 14, 1, /* baud rate gen enable, src=rtxc (BRENABL) */
- 11, 0x50, /* clocks = br gen (RCBR | TCBR) */
- 5, 0x6a, /* tx 8 bits, assert RTS (Tx8 | TxENAB | RTS) */
- 4, 0x44, /* x16 clock, 1 stop (SB1 | X16CLK)*/
- 3, 0xc1, /* rx enable, 8 bits (RxENABLE | Rx8)*/
-};
-
-/* These are for receiving and sending characters under the kgdb
- * source level kernel debugger.
- */
-void putDebugChar(char kgdb_char)
-{
- struct dec_zschannel *chan = zs_kgdbchan;
- while ((read_zsreg(chan, 0) & Tx_BUF_EMP) == 0)
- RECOVERY_DELAY;
- write_zsdata(chan, kgdb_char);
-}
-char getDebugChar(void)
-{
- struct dec_zschannel *chan = zs_kgdbchan;
- while((read_zsreg(chan, 0) & Rx_CH_AV) == 0)
- eieio(); /*barrier();*/
- return read_zsdata(chan);
-}
-void kgdb_interruptible(int yes)
-{
- struct dec_zschannel *chan = zs_kgdbchan;
- int one, nine;
- nine = read_zsreg(chan, 9);
- if (yes == 1) {
- one = EXT_INT_ENAB|RxINT_ALL;
- nine |= MIE;
- printk("turning serial ints on\n");
- } else {
- one = RxINT_DISAB;
- nine &= ~MIE;
- printk("turning serial ints off\n");
- }
- write_zsreg(chan, 1, one);
- write_zsreg(chan, 9, nine);
-}
-
-static int kgdbhook_init_channel(void *handle)
-{
- return 0;
-}
-
-static void kgdbhook_init_info(void *handle)
-{
-}
-
-static void kgdbhook_rx_char(void *handle, unsigned char ch, unsigned char fl)
-{
- struct dec_serial *info = handle;
-
- if (fl != TTY_NORMAL)
- return;
- if (ch == 0x03 || ch == '$')
- breakpoint();
-}
-
-/* This sets up the serial port we're using, and turns on
- * interrupts for that channel, so kgdb is usable once we're done.
- */
-static inline void kgdb_chaninit(struct dec_zschannel *ms, int intson, int bps)
-{
- int brg;
- int i, x;
- volatile char *sccc = ms->control;
- brg = BPS_TO_BRG(bps, zs_parms->clock/16);
- printk("setting bps on kgdb line to %d [brg=%x]\n", bps, brg);
- for (i = 20000; i != 0; --i) {
- x = *sccc; eieio();
- }
- for (i = 0; i < sizeof(scc_inittab); ++i) {
- write_zsreg(ms, scc_inittab[i], scc_inittab[i+1]);
- i++;
- }
-}
-/* This is called at boot time to prime the kgdb serial debugging
- * serial line. The 'tty_num' argument is 0 for /dev/ttya and 1
- * for /dev/ttyb which is determined in setup_arch() from the
- * boot command line flags.
- */
-struct dec_serial_hook zs_kgdbhook = {
- .init_channel = kgdbhook_init_channel,
- .init_info = kgdbhook_init_info,
- .rx_char = kgdbhook_rx_char,
- .cflags = B38400 | CS8 | CLOCAL,
-};
-
-void __init zs_kgdb_hook(int tty_num)
-{
- /* Find out how many Z8530 SCCs we have */
- if (zs_chain == 0)
- probe_sccs();
- zs_soft[tty_num].zs_channel = &zs_channels[tty_num];
- zs_kgdbchan = zs_soft[tty_num].zs_channel;
- zs_soft[tty_num].change_needed = 0;
- zs_soft[tty_num].clk_divisor = 16;
- zs_soft[tty_num].zs_baud = 38400;
- zs_soft[tty_num].hook = &zs_kgdbhook; /* This runs kgdb */
- /* Turn on transmitter/receiver at 8-bits/char */
- kgdb_chaninit(zs_soft[tty_num].zs_channel, 1, 38400);
- printk("KGDB: on channel %d initialized\n", tty_num);
- set_debug_traps(); /* init stub */
-}
-#endif /* ifdef CONFIG_KGDB */
+++ /dev/null
-/*
- * drivers/tc/zs.h: Definitions for the DECstation Z85C30 serial driver.
- *
- * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
- * Adapted from drivers/macintosh/macserial.h by Harald Koerfgen.
- *
- * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- * Copyright (C) 2004, 2005 Maciej W. Rozycki
- */
-#ifndef _DECSERIAL_H
-#define _DECSERIAL_H
-
-#include <asm/dec/serial.h>
-
-#define NUM_ZSREGS 16
-
-struct serial_struct {
- int type;
- int line;
- int port;
- int irq;
- int flags;
- int xmit_fifo_size;
- int custom_divisor;
- int baud_base;
- unsigned short close_delay;
- char reserved_char[2];
- int hub6;
- unsigned short closing_wait; /* time to wait before closing */
- unsigned short closing_wait2; /* no longer used... */
- int reserved[4];
-};
-
-/*
- * For the close wait times, 0 means wait forever for serial port to
- * flush its output. 65535 means don't wait at all.
- */
-#define ZILOG_CLOSING_WAIT_INF 0
-#define ZILOG_CLOSING_WAIT_NONE 65535
-
-/*
- * Definitions for ZILOG_struct (and serial_struct) flags field
- */
-#define ZILOG_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes
- on the callout port */
-#define ZILOG_FOURPORT 0x0002 /* Set OU1, OUT2 per AST Fourport settings */
-#define ZILOG_SAK 0x0004 /* Secure Attention Key (Orange book) */
-#define ZILOG_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */
-
-#define ZILOG_SPD_MASK 0x0030
-#define ZILOG_SPD_HI 0x0010 /* Use 56000 instead of 38400 bps */
-
-#define ZILOG_SPD_VHI 0x0020 /* Use 115200 instead of 38400 bps */
-#define ZILOG_SPD_CUST 0x0030 /* Use user-specified divisor */
-
-#define ZILOG_SKIP_TEST 0x0040 /* Skip UART test during autoconfiguration */
-#define ZILOG_AUTO_IRQ 0x0080 /* Do automatic IRQ during autoconfiguration */
-#define ZILOG_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
-#define ZILOG_PGRP_LOCKOUT 0x0200 /* Lock out cua opens based on pgrp */
-#define ZILOG_CALLOUT_NOHUP 0x0400 /* Don't do hangups for cua device */
-
-#define ZILOG_FLAGS 0x0FFF /* Possible legal ZILOG flags */
-#define ZILOG_USR_MASK 0x0430 /* Legal flags that non-privileged
- * users can set or reset */
-
-/* Internal flags used only by kernel/chr_drv/serial.c */
-#define ZILOG_INITIALIZED 0x80000000 /* Serial port was initialized */
-#define ZILOG_CALLOUT_ACTIVE 0x40000000 /* Call out device is active */
-#define ZILOG_NORMAL_ACTIVE 0x20000000 /* Normal device is active */
-#define ZILOG_BOOT_AUTOCONF 0x10000000 /* Autoconfigure port on bootup */
-#define ZILOG_CLOSING 0x08000000 /* Serial port is closing */
-#define ZILOG_CTS_FLOW 0x04000000 /* Do CTS flow control */
-#define ZILOG_CHECK_CD 0x02000000 /* i.e., CLOCAL */
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-struct dec_zschannel {
- volatile unsigned char *control;
- volatile unsigned char *data;
-
- /* Current write register values */
- unsigned char curregs[NUM_ZSREGS];
-};
-
-struct dec_serial {
- struct dec_serial *zs_next; /* For IRQ servicing chain. */
- struct dec_zschannel *zs_channel; /* Channel registers. */
- struct dec_zschannel *zs_chan_a; /* A side registers. */
- unsigned char read_reg_zero;
-
- struct dec_serial_hook *hook; /* Hook on this channel. */
- int tty_break; /* Set on BREAK condition. */
- int is_cons; /* Is this our console. */
- int tx_active; /* Char is being xmitted. */
- int tx_stopped; /* Output is suspended. */
-
- /*
- * We need to know the current clock divisor
- * to read the bps rate the chip has currently loaded.
- */
- int clk_divisor; /* May be 1, 16, 32, or 64. */
- int zs_baud;
-
- char change_needed;
-
- int magic;
- int baud_base;
- int port;
- int irq;
- int flags; /* Defined in tty.h. */
- int type; /* UART type. */
- struct tty_struct *tty;
- int read_status_mask;
- int ignore_status_mask;
- int timeout;
- int xmit_fifo_size;
- int custom_divisor;
- int x_char; /* XON/XOFF character. */
- int close_delay;
- unsigned short closing_wait;
- unsigned short closing_wait2;
- unsigned long event;
- unsigned long last_active;
- int line;
- int count; /* # of fds on device. */
- int blocked_open; /* # of blocked opens. */
- unsigned char *xmit_buf;
- int xmit_head;
- int xmit_tail;
- int xmit_cnt;
- struct tasklet_struct tlet;
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
-};
-
-
-#define SERIAL_MAGIC 0x5301
-
-/*
- * The size of the serial xmit buffer is 1 page, or 4096 bytes
- */
-#define SERIAL_XMIT_SIZE 4096
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP 0
-
-#endif /* __KERNEL__ */
-
-/* Conversion routines to/from brg time constants from/to bits
- * per second.
- */
-#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
-#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
-
-/* The Zilog register set */
-
-#define FLAG 0x7e
-
-/* Write Register 0 */
-#define R0 0 /* Register selects */
-#define R1 1
-#define R2 2
-#define R3 3
-#define R4 4
-#define R5 5
-#define R6 6
-#define R7 7
-#define R8 8
-#define R9 9
-#define R10 10
-#define R11 11
-#define R12 12
-#define R13 13
-#define R14 14
-#define R15 15
-
-#define NULLCODE 0 /* Null Code */
-#define POINT_HIGH 0x8 /* Select upper half of registers */
-#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
-#define SEND_ABORT 0x18 /* HDLC Abort */
-#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
-#define RES_Tx_P 0x28 /* Reset TxINT Pending */
-#define ERR_RES 0x30 /* Error Reset */
-#define RES_H_IUS 0x38 /* Reset highest IUS */
-
-#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
-#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
-#define RES_EOM_L 0xC0 /* Reset EOM latch */
-
-/* Write Register 1 */
-
-#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
-#define TxINT_ENAB 0x2 /* Tx Int Enable */
-#define PAR_SPEC 0x4 /* Parity is special condition */
-
-#define RxINT_DISAB 0 /* Rx Int Disable */
-#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
-#define RxINT_ALL 0x10 /* Int on all Rx Characters or error */
-#define RxINT_ERR 0x18 /* Int on error only */
-#define RxINT_MASK 0x18
-
-#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
-#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
-#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
-
-/* Write Register #2 (Interrupt Vector) */
-
-/* Write Register 3 */
-
-#define RxENABLE 0x1 /* Rx Enable */
-#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
-#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
-#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
-#define ENT_HM 0x10 /* Enter Hunt Mode */
-#define AUTO_ENAB 0x20 /* Auto Enables */
-#define Rx5 0x0 /* Rx 5 Bits/Character */
-#define Rx7 0x40 /* Rx 7 Bits/Character */
-#define Rx6 0x80 /* Rx 6 Bits/Character */
-#define Rx8 0xc0 /* Rx 8 Bits/Character */
-#define RxNBITS_MASK 0xc0
-
-/* Write Register 4 */
-
-#define PAR_ENA 0x1 /* Parity Enable */
-#define PAR_EVEN 0x2 /* Parity Even/Odd* */
-
-#define SYNC_ENAB 0 /* Sync Modes Enable */
-#define SB1 0x4 /* 1 stop bit/char */
-#define SB15 0x8 /* 1.5 stop bits/char */
-#define SB2 0xc /* 2 stop bits/char */
-#define SB_MASK 0xc
-
-#define MONSYNC 0 /* 8 Bit Sync character */
-#define BISYNC 0x10 /* 16 bit sync character */
-#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
-#define EXTSYNC 0x30 /* External Sync Mode */
-
-#define X1CLK 0x0 /* x1 clock mode */
-#define X16CLK 0x40 /* x16 clock mode */
-#define X32CLK 0x80 /* x32 clock mode */
-#define X64CLK 0xC0 /* x64 clock mode */
-#define XCLK_MASK 0xC0
-
-/* Write Register 5 */
-
-#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
-#define RTS 0x2 /* RTS */
-#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
-#define TxENAB 0x8 /* Tx Enable */
-#define SND_BRK 0x10 /* Send Break */
-#define Tx5 0x0 /* Tx 5 bits (or less)/character */
-#define Tx7 0x20 /* Tx 7 bits/character */
-#define Tx6 0x40 /* Tx 6 bits/character */
-#define Tx8 0x60 /* Tx 8 bits/character */
-#define TxNBITS_MASK 0x60
-#define DTR 0x80 /* DTR */
-
-/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
-
-/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
-
-/* Write Register 8 (transmit buffer) */
-
-/* Write Register 9 (Master interrupt control) */
-#define VIS 1 /* Vector Includes Status */
-#define NV 2 /* No Vector */
-#define DLC 4 /* Disable Lower Chain */
-#define MIE 8 /* Master Interrupt Enable */
-#define STATHI 0x10 /* Status high */
-#define SOFTACK 0x20 /* Software Interrupt Acknowledge */
-#define NORESET 0 /* No reset on write to R9 */
-#define CHRB 0x40 /* Reset channel B */
-#define CHRA 0x80 /* Reset channel A */
-#define FHWRES 0xc0 /* Force hardware reset */
-
-/* Write Register 10 (misc control bits) */
-#define BIT6 1 /* 6 bit/8bit sync */
-#define LOOPMODE 2 /* SDLC Loop mode */
-#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
-#define MARKIDLE 8 /* Mark/flag on idle */
-#define GAOP 0x10 /* Go active on poll */
-#define NRZ 0 /* NRZ mode */
-#define NRZI 0x20 /* NRZI mode */
-#define FM1 0x40 /* FM1 (transition = 1) */
-#define FM0 0x60 /* FM0 (transition = 0) */
-#define CRCPS 0x80 /* CRC Preset I/O */
-
-/* Write Register 11 (Clock Mode control) */
-#define TRxCXT 0 /* TRxC = Xtal output */
-#define TRxCTC 1 /* TRxC = Transmit clock */
-#define TRxCBR 2 /* TRxC = BR Generator Output */
-#define TRxCDP 3 /* TRxC = DPLL output */
-#define TRxCOI 4 /* TRxC O/I */
-#define TCRTxCP 0 /* Transmit clock = RTxC pin */
-#define TCTRxCP 8 /* Transmit clock = TRxC pin */
-#define TCBR 0x10 /* Transmit clock = BR Generator output */
-#define TCDPLL 0x18 /* Transmit clock = DPLL output */
-#define RCRTxCP 0 /* Receive clock = RTxC pin */
-#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
-#define RCBR 0x40 /* Receive clock = BR Generator output */
-#define RCDPLL 0x60 /* Receive clock = DPLL output */
-#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
-
-/* Write Register 12 (lower byte of baud rate generator time constant) */
-
-/* Write Register 13 (upper byte of baud rate generator time constant) */
-
-/* Write Register 14 (Misc control bits) */
-#define BRENABL 1 /* Baud rate generator enable */
-#define BRSRC 2 /* Baud rate generator source */
-#define DTRREQ 4 /* DTR/Request function */
-#define AUTOECHO 8 /* Auto Echo */
-#define LOOPBAK 0x10 /* Local loopback */
-#define SEARCH 0x20 /* Enter search mode */
-#define RMC 0x40 /* Reset missing clock */
-#define DISDPLL 0x60 /* Disable DPLL */
-#define SSBR 0x80 /* Set DPLL source = BR generator */
-#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
-#define SFMM 0xc0 /* Set FM mode */
-#define SNRZI 0xe0 /* Set NRZI mode */
-
-/* Write Register 15 (external/status interrupt control) */
-#define ZCIE 2 /* Zero count IE */
-#define DCDIE 8 /* DCD IE */
-#define SYNCIE 0x10 /* Sync/hunt IE */
-#define CTSIE 0x20 /* CTS IE */
-#define TxUIE 0x40 /* Tx Underrun/EOM IE */
-#define BRKIE 0x80 /* Break/Abort IE */
-
-
-/* Read Register 0 */
-#define Rx_CH_AV 0x1 /* Rx Character Available */
-#define ZCOUNT 0x2 /* Zero count */
-#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
-#define DCD 0x8 /* DCD */
-#define SYNC_HUNT 0x10 /* Sync/hunt */
-#define CTS 0x20 /* CTS */
-#define TxEOM 0x40 /* Tx underrun */
-#define BRK_ABRT 0x80 /* Break/Abort */
-
-/* Read Register 1 */
-#define ALL_SNT 0x1 /* All sent */
-/* Residue Data for 8 Rx bits/char programmed */
-#define RES3 0x8 /* 0/3 */
-#define RES4 0x4 /* 0/4 */
-#define RES5 0xc /* 0/5 */
-#define RES6 0x2 /* 0/6 */
-#define RES7 0xa /* 0/7 */
-#define RES8 0x6 /* 0/8 */
-#define RES18 0xe /* 1/8 */
-#define RES28 0x0 /* 2/8 */
-/* Special Rx Condition Interrupts */
-#define PAR_ERR 0x10 /* Parity error */
-#define Rx_OVR 0x20 /* Rx Overrun Error */
-#define FRM_ERR 0x40 /* CRC/Framing Error */
-#define END_FR 0x80 /* End of Frame (SDLC) */
-
-/* Read Register 2 (channel b only) - Interrupt vector */
-
-/* Read Register 3 (interrupt pending register) ch a only */
-#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
-#define CHBTxIP 0x2 /* Channel B Tx IP */
-#define CHBRxIP 0x4 /* Channel B Rx IP */
-#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
-#define CHATxIP 0x10 /* Channel A Tx IP */
-#define CHARxIP 0x20 /* Channel A Rx IP */
-
-/* Read Register 8 (receive data register) */
-
-/* Read Register 10 (misc status bits) */
-#define ONLOOP 2 /* On loop */
-#define LOOPSEND 0x10 /* Loop sending */
-#define CLK2MIS 0x40 /* Two clocks missing */
-#define CLK1MIS 0x80 /* One clock missing */
-
-/* Read Register 12 (lower byte of baud rate generator constant) */
-
-/* Read Register 13 (upper byte of baud rate generator constant) */
-
-/* Read Register 15 (value of WR 15) */
-
-/* Misc macros */
-#define ZS_CLEARERR(channel) (write_zsreg(channel, 0, ERR_RES))
-#define ZS_CLEARFIFO(channel) do { volatile unsigned char garbage; \
- garbage = read_zsdata(channel); \
- garbage = read_zsdata(channel); \
- garbage = read_zsdata(channel); \
- } while(0)
-
-#endif /* !(_DECSERIAL_H) */
+++ /dev/null
-/*
- * include/asm-mips/dec/serial.h
- *
- * Definitions common to all DECstation serial devices.
- *
- * Copyright (C) 2004 Maciej W. Rozycki
- *
- * Based on bits extracted from drivers/tc/zs.h for which
- * the following copyrights apply:
- *
- * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
- * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
- * Copyright (C) Harald Koerfgen
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-#ifndef __ASM_MIPS_DEC_SERIAL_H
-#define __ASM_MIPS_DEC_SERIAL_H
-
-struct dec_serial_hook {
- int (*init_channel)(void *handle);
- void (*init_info)(void *handle);
- void (*rx_char)(unsigned char ch, unsigned char fl);
- int (*poll_rx_char)(void *handle);
- int (*poll_tx_char)(void *handle, unsigned char ch);
- unsigned int cflags;
-};
-
-extern int register_dec_serial_hook(unsigned int channel,
- struct dec_serial_hook *hook);
-extern int unregister_dec_serial_hook(unsigned int channel);
-
-#endif /* __ASM_MIPS_DEC_SERIAL_H */
/* NEC v850. */
#define PORT_V850E_UART 40
-/* DZ */
-#define PORT_DZ 47
+/* DEC */
+#define PORT_DZ 46
+#define PORT_ZS 47
/* Parisc type numbers. */
#define PORT_MUX 48
projects / cascardo / linux.git / commitdiff