dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
integratorcp.dtb
dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
-dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-cloudbox.dtb \
+dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-b3.dtb \
+ kirkwood-cloudbox.dtb \
kirkwood-db-88f6281.dtb \
kirkwood-db-88f6282.dtb \
kirkwood-dns320.dtb \
kirkwood-sheevaplug-esata.dtb \
kirkwood-topkick.dtb \
kirkwood-ts219-6281.dtb \
- kirkwood-ts219-6282.dtb
+ kirkwood-ts219-6282.dtb \
+ kirkwood-ts419-6281.dtb \
+ kirkwood-ts419-6282.dtb
dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb
dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
dtb-$(CONFIG_ARCH_MSM) += qcom-msm8660-surf.dtb \
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
#include "armada-370.dtsi"
/ {
green_pwr_led {
label = "mirabox:green:pwr";
- gpios = <&gpio1 31 1>;
+ gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
blue_stat_led {
label = "mirabox:blue:stat";
- gpios = <&gpio2 0 1>;
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
default-state = "off";
};
green_stat_led {
label = "mirabox:green:stat";
- gpios = <&gpio2 1 1>;
+ gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
default-state = "off";
};
};
*/
/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
#include "armada-370.dtsi"
/ {
#size-cells = <0>;
button@1 {
label = "Software Button";
- linux,code = <116>;
- gpios = <&gpio0 6 1>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
};
};
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "armada-xp-mv78230.dtsi"
/ {
button@1 {
label = "Factory Reset Button";
- linux,code = <141>; /* KEY_SETUP */
- gpios = <&gpio1 1 1>;
+ linux,code = <KEY_SETUP>;
+ gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
};
};
};
*/
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
#include "armada-xp-mv78260.dtsi"
/ {
red_led {
label = "red_led";
- gpios = <&gpio1 17 1>;
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
default-state = "off";
};
yellow_led {
label = "yellow_led";
- gpios = <&gpio1 19 1>;
+ gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
default-state = "off";
};
green_led {
label = "green_led";
- gpios = <&gpio1 21 1>;
+ gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
default-state = "keep";
};
};
button@1 {
label = "Init Button";
- linux,code = <116>;
- gpios = <&gpio1 28 0>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
};
};
--- /dev/null
+/*
+ * Device Tree file for Excito Bubba B3
+ *
+ * Copyright (C) 2013, Andrew Lunn <andrew@lunn.ch>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ *
+ * Note: This requires a new'ish version of u-boot, which disables the
+ * L2 cache. If your B3 silently fails to boot, u-boot is probably too
+ * old. Either upgrade, or consider the following email:
+ *
+ * http://lists.debian.org/debian-arm/2012/08/msg00128.html
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Excito B3";
+ compatible = "excito,b3", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ memory { /* 512 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ };
+
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ /* Wifi model has Atheros chipset on pcie port */
+ pcie@1,0 {
+ status = "okay";
+ };
+ };
+ };
+
+ ocp@f1000000 {
+ pinctrl: pinctrl@10000 {
+ pmx_button_power: pmx-button-power {
+ marvell,pins = "mpp39";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led-green {
+ marvell,pins = "mpp38";
+ marvell,function = "gpio";
+ };
+ pmx_led_red: pmx-led-red {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ pmx_led_blue: pmx-led-blue {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+ pmx_beeper: pmx-beeper {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ };
+
+ spi@10600 {
+ status = "okay";
+ pinctrl-0 = <&pmx_spi>;
+ pinctrl-names = "default";
+
+ m25p16@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p16";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ mode = <0>;
+
+ partition@0 {
+ reg = <0x0 0xc0000>;
+ label = "u-boot";
+ };
+
+ partition@c0000 {
+ reg = <0xc0000 0x20000>;
+ label = "u-boot env";
+ };
+
+ partition@e0000 {
+ reg = <0xe0000 0x120000>;
+ label = "data";
+ };
+ };
+ };
+
+ i2c@11000 {
+ status = "okay";
+ /*
+ * There is something on the bus at address 0x64.
+ * Not yet identified what it is, maybe the eeprom
+ * for the Atheros WiFi chip?
+ */
+ };
+
+
+ serial@12000 {
+ /* Internal on test pins, 3.3v TTL
+ * UART0_RX = Testpoint 65
+ * UART0_TX = Testpoint 66
+ * See the Excito Wiki for more details.
+ */
+ pinctrl-0 = <&pmx_uart0>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ sata@80000 {
+ /* One internal, the second as eSATA */
+ status = "okay";
+ nr-ports = <2>;
+ };
+ };
+
+ gpio-leds {
+ /*
+ * There is one LED "port" on the front and the colours
+ * mix together giving some interesting combinations.
+ */
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_green &pmx_led_red
+ &pmx_led_blue >;
+ pinctrl-names = "default";
+
+ programming_led {
+ label = "bubba3:green:programming";
+ gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ error_led {
+ label = "bubba3:red:error";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ active_led {
+ label = "bubba3:blue:active";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_button_power>;
+ pinctrl-names = "default";
+
+ power-button {
+ /* On the back */
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ beeper: beeper {
+ /* 4KHz Piezoelectric buzzer */
+ compatible = "gpio-beeper";
+ pinctrl-0 = <&pmx_beeper>;
+ pinctrl-names = "default";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@8 {
+ device_type = "ethernet-phy";
+ reg = <8>;
+ };
+
+ ethphy1: ethernet-phy@24 {
+ device_type = "ethernet-phy";
+ reg = <24>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
+
+ð1 {
+ status = "okay";
+ ethernet1-port@0 {
+ phy-handle = <ðphy1>;
+ };
+};
+
--- /dev/null
+/*
+ * Device Tree file for QNAP TS41X with 6281 SoC
+ *
+ * Copyright (C) 2013, Andrew Lunn <andrew@lunn.ch>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include "kirkwood-ts219.dtsi"
+#include "kirkwood-ts419.dtsi"
+
+ðphy0 { reg = <8>; };
+ðphy1 { reg = <0>; };
--- /dev/null
+/*
+ * Device Tree file for QNAP TS41X with 6282 SoC
+ *
+ * Copyright (C) 2013, Andrew Lunn <andrew@lunn.ch>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+#include "kirkwood-ts219.dtsi"
+#include "kirkwood-ts419.dtsi"
+
+/ {
+ mbus {
+ pcie-controller {
+ status = "okay";
+
+ pcie@2,0 {
+ status = "okay";
+ };
+ };
+ };
+};
+
+ðphy0 { reg = <0>; };
+ðphy1 { reg = <1>; };
--- /dev/null
+/*
+ * Device Tree include file for QNAP TS41X
+ *
+ * Copyright (C) 2013, Andrew Lunn <andrew@lunn.ch>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+/ {
+ model = "QNAP TS419 family";
+ compatible = "qnap,ts419", "marvell,kirkwood";
+
+ ocp@f1000000 {
+ pinctrl: pinctrl@10000 {
+ pinctrl-names = "default";
+
+ pmx_USB_copy_button: pmx-USB-copy-button {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ pmx_reset_button: pmx-reset-button {
+ marvell,pins = "mpp37";
+ marvell,function = "gpio";
+ };
+ /*
+ * JP1 indicates if an LCD module is installed
+ * on the serial port (0), or if the port is used
+ * as a console (1).
+ */
+ pmx_jumper_jp1: pmx-jumper_jp1 {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_reset_button &pmx_USB_copy_button>;
+ pinctrl-names = "default";
+
+ button@1 {
+ label = "USB Copy";
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+ };
+ button@2 {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy1: ethernet-phy@1 {
+ device_type = "ethernet-phy";
+ /* overwrite reg property in board file */
+ };
+};
+
+ð1 {
+ status = "okay";
+ ethernet1-port@0 {
+ phy-handle = <ðphy1>;
+ };
+};
projects / cascardo / linux.git / commitdiff