mtd: denali: detect the number of banks

Not all configurations of the Denali controller support 4 banks.  The
controller can support between 1 and 16 banks.  Detect this from the
design features register.

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index 5568640..8c5dc89 100644 (file)
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -178,11 +178,11 @@ static uint16_t denali_nand_reset(struct denali_nand_info *denali)
        dev_dbg(denali->dev, "%s, Line %d, Function: %s\n",
                       __FILE__, __LINE__, __func__);
 
-       for (i = 0 ; i < LLD_MAX_FLASH_BANKS; i++)
+       for (i = 0 ; i < denali->max_banks; i++)
                iowrite32(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
                denali->flash_reg + INTR_STATUS(i));
 
-       for (i = 0 ; i < LLD_MAX_FLASH_BANKS; i++) {
+       for (i = 0 ; i < denali->max_banks; i++) {
                iowrite32(1 << i, denali->flash_reg + DEVICE_RESET);
                while (!(ioread32(denali->flash_reg +
                                INTR_STATUS(i)) &
@@ -194,7 +194,7 @@ static uint16_t denali_nand_reset(struct denali_nand_info *denali)
                        "NAND Reset operation timed out on bank %d\n", i);
        }
 
-       for (i = 0; i < LLD_MAX_FLASH_BANKS; i++)
+       for (i = 0; i < denali->max_banks; i++)
                iowrite32(INTR_STATUS__RST_COMP | INTR_STATUS__TIME_OUT,
                        denali->flash_reg + INTR_STATUS(i));
 
@@ -405,11 +405,11 @@ static void get_hynix_nand_para(struct denali_nand_info *denali,
  */
 static void find_valid_banks(struct denali_nand_info *denali)
 {
-       uint32_t id[LLD_MAX_FLASH_BANKS];
+       uint32_t id[denali->max_banks];
        int i;
 
        denali->total_used_banks = 1;
-       for (i = 0; i < LLD_MAX_FLASH_BANKS; i++) {
+       for (i = 0; i < denali->max_banks; i++) {
                index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 0), 0x90);
                index_addr(denali, (uint32_t)(MODE_11 | (i << 24) | 1), 0);
                index_addr_read_data(denali,
@@ -445,6 +445,17 @@ static void find_valid_banks(struct denali_nand_info *denali)
                "denali->total_used_banks: %d\n", denali->total_used_banks);
 }
 
+/*
+ * Use the configuration feature register to determine the maximum number of
+ * banks that the hardware supports.
+ */
+static void detect_max_banks(struct denali_nand_info *denali)
+{
+       uint32_t features = ioread32(denali->flash_reg + FEATURES);
+
+       denali->max_banks = 2 << (features & FEATURES__N_BANKS);
+}
+
 static void detect_partition_feature(struct denali_nand_info *denali)
 {
        /* For MRST platform, denali->fwblks represent the
@@ -562,7 +573,7 @@ static void denali_irq_init(struct denali_nand_info *denali)
        int_mask = DENALI_IRQ_ALL;
 
        /* Clear all status bits */
-       for (i = 0; i < LLD_MAX_FLASH_BANKS; ++i)
+       for (i = 0; i < denali->max_banks; ++i)
                iowrite32(0xFFFF, denali->flash_reg + INTR_STATUS(i));
 
        denali_irq_enable(denali, int_mask);
@@ -579,7 +590,7 @@ static void denali_irq_enable(struct denali_nand_info *denali,
 {
        int i;
 
-       for (i = 0; i < LLD_MAX_FLASH_BANKS; ++i)
+       for (i = 0; i < denali->max_banks; ++i)
                iowrite32(int_mask, denali->flash_reg + INTR_EN(i));
 }
 
@@ -1345,6 +1356,7 @@ static void denali_hw_init(struct denali_nand_info *denali)
        /* Should set value for these registers when init */
        iowrite32(0, denali->flash_reg + TWO_ROW_ADDR_CYCLES);
        iowrite32(1, denali->flash_reg + ECC_ENABLE);
+       detect_max_banks(denali);
        denali_nand_timing_set(denali);
        denali_irq_init(denali);
 }
@@ -1522,7 +1534,7 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
        /* scan for NAND devices attached to the controller
         * this is the first stage in a two step process to register
         * with the nand subsystem */
-       if (nand_scan_ident(&denali->mtd, LLD_MAX_FLASH_BANKS, NULL)) {
+       if (nand_scan_ident(&denali->mtd, denali->max_banks, NULL)) {
                ret = -ENXIO;
                goto failed_req_irq;
        }

diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/denali.h
index 638668c..fabb9d5 100644 (file)
--- a/drivers/mtd/nand/denali.h
+++ b/drivers/mtd/nand/denali.h
@@ -454,7 +454,6 @@
 #define READ_WRITE_ENABLE_HIGH_COUNT    22
 
 #define ECC_SECTOR_SIZE     512
-#define LLD_MAX_FLASH_BANKS     4
 
 #define DENALI_BUF_SIZE                (NAND_MAX_PAGESIZE + NAND_MAX_OOBSIZE)
 
@@ -494,6 +493,7 @@ struct denali_nand_info {
        uint32_t totalblks;
        uint32_t blksperchip;
        uint32_t bbtskipbytes;
+       uint32_t max_banks;
 };
 
 #endif /*_LLD_NAND_*/