From: Felipe Balbi <balbi@ti.com>
Date: Fri, 27 Feb 2015 19:19:39 +0000 (-0600)
Subject: usb: musb: cppi41: decrease indentation level
X-Git-Tag: v4.1-rc1~154^2~4^2~88
X-Git-Url: http://git.cascardo.info/?a=commitdiff_plain;h=1b61625f8b5d87caf9633d7dbfbaf1ea8270036d;p=cascardo%2Flinux.git

usb: musb: cppi41: decrease indentation level

no functional changes, clean up only.

Signed-off-by: Felipe Balbi <balbi@ti.com>
---

diff --git a/drivers/usb/musb/musb_cppi41.c b/drivers/usb/musb/musb_cppi41.c
index be84562d021b..73ac9835485d 100644
--- a/drivers/usb/musb/musb_cppi41.c
+++ b/drivers/usb/musb/musb_cppi41.c
@@ -225,10 +225,12 @@ static void cppi41_dma_callback(void *private_data)
 	struct dma_channel *channel = private_data;
 	struct cppi41_dma_channel *cppi41_channel = channel->private_data;
 	struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep;
+	struct cppi41_dma_controller *controller;
 	struct musb *musb = hw_ep->musb;
 	unsigned long flags;
 	struct dma_tx_state txstate;
 	u32 transferred;
+	int is_hs = 0;
 	bool empty;
 
 	spin_lock_irqsave(&musb->lock, flags);
@@ -251,58 +253,58 @@ static void cppi41_dma_callback(void *private_data)
 	empty = musb_is_tx_fifo_empty(hw_ep);
 	if (empty) {
 		cppi41_trans_done(cppi41_channel);
-	} else {
-		struct cppi41_dma_controller *controller;
-		int is_hs = 0;
-		/*
-		 * On AM335x it has been observed that the TX interrupt fires
-		 * too early that means the TXFIFO is not yet empty but the DMA
-		 * engine says that it is done with the transfer. We don't
-		 * receive a FIFO empty interrupt so the only thing we can do is
-		 * to poll for the bit. On HS it usually takes 2us, on FS around
-		 * 110us - 150us depending on the transfer size.
-		 * We spin on HS (no longer than than 25us and setup a timer on
-		 * FS to check for the bit and complete the transfer.
-		 */
-		controller = cppi41_channel->controller;
+		goto out;
+	}
 
-		if (is_host_active(musb)) {
-			if (musb->port1_status & USB_PORT_STAT_HIGH_SPEED)
-				is_hs = 1;
-		} else {
-			if (musb->g.speed == USB_SPEED_HIGH)
-				is_hs = 1;
-		}
-		if (is_hs) {
-			unsigned wait = 25;
-
-			do {
-				empty = musb_is_tx_fifo_empty(hw_ep);
-				if (empty)
-					break;
-				wait--;
-				if (!wait)
-					break;
-				udelay(1);
-			} while (1);
+	/*
+	 * On AM335x it has been observed that the TX interrupt fires
+	 * too early that means the TXFIFO is not yet empty but the DMA
+	 * engine says that it is done with the transfer. We don't
+	 * receive a FIFO empty interrupt so the only thing we can do is
+	 * to poll for the bit. On HS it usually takes 2us, on FS around
+	 * 110us - 150us depending on the transfer size.
+	 * We spin on HS (no longer than than 25us and setup a timer on
+	 * FS to check for the bit and complete the transfer.
+	 */
+	controller = cppi41_channel->controller;
+
+	if (is_host_active(musb)) {
+		if (musb->port1_status & USB_PORT_STAT_HIGH_SPEED)
+			is_hs = 1;
+	} else {
+		if (musb->g.speed == USB_SPEED_HIGH)
+			is_hs = 1;
+	}
+	if (is_hs) {
+		unsigned wait = 25;
 
+		do {
 			empty = musb_is_tx_fifo_empty(hw_ep);
-			if (empty) {
-				cppi41_trans_done(cppi41_channel);
-				goto out;
-			}
+			if (empty)
+				break;
+			wait--;
+			if (!wait)
+				break;
+			udelay(1);
+		} while (1);
+
+		empty = musb_is_tx_fifo_empty(hw_ep);
+		if (empty) {
+			cppi41_trans_done(cppi41_channel);
+			goto out;
 		}
-		list_add_tail(&cppi41_channel->tx_check,
-				&controller->early_tx_list);
-		if (!hrtimer_is_queued(&controller->early_tx)) {
-			unsigned long usecs = cppi41_channel->total_len / 10;
+	}
+	list_add_tail(&cppi41_channel->tx_check,
+			&controller->early_tx_list);
+	if (!hrtimer_is_queued(&controller->early_tx)) {
+		unsigned long usecs = cppi41_channel->total_len / 10;
 
-			hrtimer_start_range_ns(&controller->early_tx,
+		hrtimer_start_range_ns(&controller->early_tx,
 				ktime_set(0, usecs * NSEC_PER_USEC),
 				20 * NSEC_PER_USEC,
 				HRTIMER_MODE_REL);
-		}
 	}
+
 out:
 	spin_unlock_irqrestore(&musb->lock, flags);
 }