Double-quotes can be used to protect spaces in values, e.g.:
param="spaces in here"
+cpu lists:
+----------
+
+Some kernel parameters take a list of CPUs as a value, e.g. isolcpus,
+nohz_full, irqaffinity, rcu_nocbs. The format of this list is:
+
+ <cpu number>,...,<cpu number>
+
+or
+
+ <cpu number>-<cpu number>
+ (must be a positive range in ascending order)
+
+or a mixture
+
+<cpu number>,...,<cpu number>-<cpu number>
+
+Note that for the special case of a range one can split the range into equal
+sized groups and for each group use some amount from the beginning of that
+group:
+
+ <cpu number>-cpu number>:<used size>/<group size>
+
+For example one can add to the command line following parameter:
+
+ isolcpus=1,2,10-20,100-2000:2/25
+
+where the final item represents CPUs 100,101,125,126,150,151,...
+
+
+
This document may not be entirely up to date and comprehensive. The command
"modinfo -p ${modulename}" shows a current list of all parameters of a loadable
module. Loadable modules, after being loaded into the running kernel, also
driver will print ACPI tables for AMD IOMMU during
IOMMU initialization.
+ amd_iommu_intr= [HW,X86-64]
+ Specifies one of the following AMD IOMMU interrupt
+ remapping modes:
+ legacy - Use legacy interrupt remapping mode.
+ vapic - Use virtual APIC mode, which allows IOMMU
+ to inject interrupts directly into guest.
+ This mode requires kvm-amd.avic=1.
+ (Default when IOMMU HW support is present.)
+
amijoy.map= [HW,JOY] Amiga joystick support
Map of devices attached to JOY0DAT and JOY1DAT
Format: <a>,<b>
loops can be debugged more effectively on production
systems.
+ clocksource.arm_arch_timer.fsl-a008585=
+ [ARM64]
+ Format: <bool>
+ Enable/disable the workaround of Freescale/NXP
+ erratum A-008585. This can be useful for KVM
+ guests, if the guest device tree doesn't show the
+ erratum. If unspecified, the workaround is
+ enabled based on the device tree.
+
clearcpuid=BITNUM [X86]
Disable CPUID feature X for the kernel. See
arch/x86/include/asm/cpufeatures.h for the valid bit
determined by the stdout-path property in device
tree's chosen node.
- cdns,<addr>
- Start an early, polled-mode console on a cadence serial
- port at the specified address. The cadence serial port
- must already be setup and configured. Options are not
- yet supported.
+ cdns,<addr>[,options]
+ Start an early, polled-mode console on a Cadence
+ (xuartps) serial port at the specified address. Only
+ supported option is baud rate. If baud rate is not
+ specified, the serial port must already be setup and
+ configured.
uart[8250],io,<addr>[,options]
uart[8250],mmio,<addr>[,options]
Format: <unsigned int> such that (rxsize & ~0x1fffc0) == 0.
Default: 1024
+ gpio-mockup.gpio_mockup_ranges
+ [HW] Sets the ranges of gpiochip of for this device.
+ Format: <start1>,<end1>,<start2>,<end2>...
+
hardlockup_all_cpu_backtrace=
[KNL] Should the hard-lockup detector generate
backtraces on all cpus.
initrd= [BOOT] Specify the location of the initial ramdisk
+ init_pkru= [x86] Specify the default memory protection keys rights
+ register contents for all processes. 0x55555554 by
+ default (disallow access to all but pkey 0). Can
+ override in debugfs after boot.
+
inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
Format: <irq>
intel_idle.max_cstate= [KNL,HW,ACPI,X86]
0 disables intel_idle and fall back on acpi_idle.
- 1 to 6 specify maximum depth of C-state.
+ 1 to 9 specify maximum depth of C-state.
intel_pstate= [X86]
disable
See Documentation/filesystems/nfs/nfsroot.txt.
irqaffinity= [SMP] Set the default irq affinity mask
- Format:
- <cpu number>,...,<cpu number>
- or
- <cpu number>-<cpu number>
- (must be a positive range in ascending order)
- or a mixture
- <cpu number>,...,<cpu number>-<cpu number>
+ The argument is a cpu list, as described above.
irqfixup [HW]
When an interrupt is not handled search all handlers
Format: <RDP>,<reset>,<pci_scan>,<verbosity>
isolcpus= [KNL,SMP] Isolate CPUs from the general scheduler.
- Format:
- <cpu number>,...,<cpu number>
- or
- <cpu number>-<cpu number>
- (must be a positive range in ascending order)
- or a mixture
- <cpu number>,...,<cpu number>-<cpu number>
+ The argument is a cpu list, as described above.
This option can be used to specify one or more CPUs
to isolate from the general SMP balancing and scheduling
than or equal to this physical address is ignored.
maxcpus= [SMP] Maximum number of processors that an SMP kernel
- should make use of. maxcpus=n : n >= 0 limits the
- kernel to using 'n' processors. n=0 is a special case,
- it is equivalent to "nosmp", which also disables
- the IO APIC.
+ will bring up during bootup. maxcpus=n : n >= 0 limits
+ the kernel to bring up 'n' processors. Surely after
+ bootup you can bring up the other plugged cpu by executing
+ "echo 1 > /sys/devices/system/cpu/cpuX/online". So maxcpus
+ only takes effect during system bootup.
+ While n=0 is a special case, it is equivalent to "nosmp",
+ which also disables the IO APIC.
max_loop= [LOOP] The number of loop block devices that get
(loop.max_loop) unconditionally pre-created at init time. The default
nodelayacct [KNL] Disable per-task delay accounting
- nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects.
-
nodsp [SH] Disable hardware DSP at boot time.
noefi Disable EFI runtime services support.
Default: on
nohz_full= [KNL,BOOT]
+ The argument is a cpu list, as described above.
In kernels built with CONFIG_NO_HZ_FULL=y, set
the specified list of CPUs whose tick will be stopped
whenever possible. The boot CPU will be forced outside
nr_cpus= [SMP] Maximum number of processors that an SMP kernel
could support. nr_cpus=n : n >= 1 limits the kernel to
- supporting 'n' processors. Later in runtime you can not
- use hotplug cpu feature to put more cpu back to online.
- just like you compile the kernel NR_CPUS=n
+ support 'n' processors. It could be larger than the
+ number of already plugged CPU during bootup, later in
+ runtime you can physically add extra cpu until it reaches
+ n. So during boot up some boot time memory for per-cpu
+ variables need be pre-allocated for later physical cpu
+ hot plugging.
nr_uarts= [SERIAL] maximum number of UARTs to be registered.
See Documentation/blockdev/ramdisk.txt.
rcu_nocbs= [KNL]
+ The argument is a cpu list, as described above.
+
In kernels built with CONFIG_RCU_NOCB_CPU=y, set
the specified list of CPUs to be no-callback CPUs.
Invocation of these CPUs' RCU callbacks will
u = IGNORE_UAS (don't bind to the uas driver);
w = NO_WP_DETECT (don't test whether the
medium is write-protected).
+ y = ALWAYS_SYNC (issue a SYNCHRONIZE_CACHE
+ even if the device claims no cache)
Example: quirks=0419:aaf5:rl,0421:0433:rc
user_debug= [KNL,ARM]
projects / cascardo / linux.git / blobdiff