#define KVM_IRQ_ROUTING_HV_SINT 4
flags:
-- KVM_MSI_VALID_DEVID: used along with KVM_IRQ_ROUTING_MSI
- routing entry type, specifies that the devid field contains
- a valid value.
+- KVM_MSI_VALID_DEVID: used along with KVM_IRQ_ROUTING_MSI routing entry
+ type, specifies that the devid field contains a valid value. The per-VM
+ KVM_CAP_MSI_DEVID capability advertises the requirement to provide
+ the device ID. If this capability is not available, userspace should
+ never set the KVM_MSI_VALID_DEVID flag as the ioctl might fail.
- zero otherwise
struct kvm_irq_routing_irqchip {
};
};
-devid: If KVM_MSI_VALID_DEVID is set, contains a unique device identifier
- for the device that wrote the MSI message.
- For PCI, this is usually a BFD identifier in the lower 16 bits.
+If KVM_MSI_VALID_DEVID is set, devid contains a unique device identifier
+for the device that wrote the MSI message. For PCI, this is usually a
+BFD identifier in the lower 16 bits.
-The per-VM KVM_CAP_MSI_DEVID capability advertises the requirement to
-provide the device ID. If this capability is not set, userland cannot
-rely on the kernel to allow the KVM_MSI_VALID_DEVID flag being set.
+On x86, address_hi is ignored unless the KVM_X2APIC_API_USE_32BIT_IDS
+feature of KVM_CAP_X2APIC_API capability is enabled. If it is enabled,
+address_hi bits 31-8 provide bits 31-8 of the destination id. Bits 7-0 of
+address_hi must be zero.
struct kvm_irq_routing_s390_adapter {
__u64 ind_addr;
Reads the Local APIC registers and copies them into the input argument. The
data format and layout are the same as documented in the architecture manual.
+If KVM_X2APIC_API_USE_32BIT_IDS feature of KVM_CAP_X2APIC_API is
+enabled, then the format of APIC_ID register depends on the APIC mode
+(reported by MSR_IA32_APICBASE) of its VCPU. x2APIC stores APIC ID in
+the APIC_ID register (bytes 32-35). xAPIC only allows an 8-bit APIC ID
+which is stored in bits 31-24 of the APIC register, or equivalently in
+byte 35 of struct kvm_lapic_state's regs field. KVM_GET_LAPIC must then
+be called after MSR_IA32_APICBASE has been set with KVM_SET_MSR.
+
+If KVM_X2APIC_API_USE_32BIT_IDS feature is disabled, struct kvm_lapic_state
+always uses xAPIC format.
+
4.58 KVM_SET_LAPIC
Copies the input argument into the Local APIC registers. The data format
and layout are the same as documented in the architecture manual.
+The format of the APIC ID register (bytes 32-35 of struct kvm_lapic_state's
+regs field) depends on the state of the KVM_CAP_X2APIC_API capability.
+See the note in KVM_GET_LAPIC.
+
4.59 KVM_IOEVENTFD
__u8 pad[12];
};
-flags: KVM_MSI_VALID_DEVID: devid contains a valid value
-devid: If KVM_MSI_VALID_DEVID is set, contains a unique device identifier
- for the device that wrote the MSI message.
- For PCI, this is usually a BFD identifier in the lower 16 bits.
+flags: KVM_MSI_VALID_DEVID: devid contains a valid value. The per-VM
+ KVM_CAP_MSI_DEVID capability advertises the requirement to provide
+ the device ID. If this capability is not available, userspace
+ should never set the KVM_MSI_VALID_DEVID flag as the ioctl might fail.
-The per-VM KVM_CAP_MSI_DEVID capability advertises the need to provide
-the device ID. If this capability is not set, userland cannot rely on
-the kernel to allow the KVM_MSI_VALID_DEVID flag being set.
+If KVM_MSI_VALID_DEVID is set, devid contains a unique device identifier
+for the device that wrote the MSI message. For PCI, this is usually a
+BFD identifier in the lower 16 bits.
+
+On x86, address_hi is ignored unless the KVM_CAP_X2APIC_API capability is
+enabled. If it is enabled, address_hi bits 31-8 provide bits 31-8 of the
+destination id. Bits 7-0 of address_hi must be zero.
4.71 KVM_CREATE_PIT2
Will return -EINVAL if the machine does not support runtime-instrumentation.
Will return -EBUSY if a VCPU has already been created.
+7.7 KVM_CAP_X2APIC_API
+
+Architectures: x86
+Parameters: args[0] - features that should be enabled
+Returns: 0 on success, -EINVAL when args[0] contains invalid features
+
+Valid feature flags in args[0] are
+
+#define KVM_X2APIC_API_USE_32BIT_IDS (1ULL << 0)
+#define KVM_X2APIC_API_DISABLE_BROADCAST_QUIRK (1ULL << 1)
+
+Enabling KVM_X2APIC_API_USE_32BIT_IDS changes the behavior of
+KVM_SET_GSI_ROUTING, KVM_SIGNAL_MSI, KVM_SET_LAPIC, and KVM_GET_LAPIC,
+allowing the use of 32-bit APIC IDs. See KVM_CAP_X2APIC_API in their
+respective sections.
+
+KVM_X2APIC_API_DISABLE_BROADCAST_QUIRK must be enabled for x2APIC to work
+in logical mode or with more than 255 VCPUs. Otherwise, KVM treats 0xff
+as a broadcast even in x2APIC mode in order to support physical x2APIC
+without interrupt remapping. This is undesirable in logical mode,
+where 0xff represents CPUs 0-7 in cluster 0.
+
+7.8 KVM_CAP_S390_USER_INSTR0
+
+Architectures: s390
+Parameters: none
+
+With this capability enabled, all illegal instructions 0x0000 (2 bytes) will
+be intercepted and forwarded to user space. User space can use this
+mechanism e.g. to realize 2-byte software breakpoints. The kernel will
+not inject an operating exception for these instructions, user space has
+to take care of that.
+
+This capability can be enabled dynamically even if VCPUs were already
+created and are running.
+
8. Other capabilities.
----------------------
projects / cascardo / linux.git / blobdiff