Merge tag 'cris-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper...

[cascardo/linux.git] / arch / arm / boot / dts / sun8i-h3-orangepi-plus.dts

diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
index 79f40c3..bb58591 100644 (file)
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
@@ -40,95 +40,56 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+/* The Orange Pi Plus is an extended version of the Orange Pi 2 */
+#include "sun8i-h3-orangepi-2.dts"
 
 / {
-       model = "Xunlong Orange Pi Plus";
+       model = "Xunlong Orange Pi Plus / Plus 2";
        compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
 
-       aliases {
-               serial0 = &uart0;
-       };
-
-       chosen {
-               stdout-path = "serial0:115200n8";
-       };
-
-       leds {
-               compatible = "gpio-leds";
+       reg_usb3_vbus: usb3-vbus {
+               compatible = "regulator-fixed";
                pinctrl-names = "default";
-               pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
-
-               status_led {
-                       label = "orangepi-plus:red:status";
-                       gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
-               };
-
-               pwr_led {
-                       label = "orangepi-plus:green:pwr";
-                       gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
-                       default-state = "on";
-               };
+               pinctrl-0 = <&usb3_vbus_pin_a>;
+               regulator-name = "usb3-vbus";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               regulator-boot-on;
+               enable-active-high;
+               gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
        };
+};
 
-       r_gpio_keys {
-               compatible = "gpio-keys";
-               input-name = "sw4";
-
-               pinctrl-names = "default";
-               pinctrl-0 = <&sw_r_opc>;
+&ehci3 {
+       status = "okay";
+};
 
-               sw4@0 {
-                       label = "sw4";
-                       linux,code = <BTN_0>;
-                       gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
-               };
-       };
+&mmc2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc2_8bit_pins>;
+       vmmc-supply = <&reg_vcc3v3>;
+       bus-width = <8>;
+       non-removable;
+       cap-mmc-hw-reset;
+       status = "okay";
 };
 
-&pio {
-       leds_opc: led_pins@0 {
-               allwinner,pins = "PA15";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
+&mmc2_8bit_pins {
+       /* Increase drive strength for DDR modes */
+       allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+       /* eMMC is missing pull-ups */
+       allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 };
 
-&r_pio {
-       leds_r_opc: led_pins@0 {
-               allwinner,pins = "PL10";
+&pio {
+       usb3_vbus_pin_a: usb3_vbus_pin@0 {
+               allwinner,pins = "PG11";
                allwinner,function = "gpio_out";
                allwinner,drive = <SUN4I_PINCTRL_10_MA>;
                allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
        };
-
-       sw_r_opc: key_pins@0 {
-               allwinner,pins = "PL03";
-               allwinner,function = "gpio_in";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-};
-
-&mmc0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
-       vmmc-supply = <&reg_vcc3v3>;
-       bus-width = <4>;
-       cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-       cd-inverted;
-       status = "okay";
 };
 
-&uart0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&uart0_pins_a>;
-       status = "okay";
+&usbphy {
+       usb3_vbus-supply = <&reg_usb3_vbus>;
 };