#include <linux/mmc/sh_mmcif.h>
#include <linux/mmc/sh_mobile_sdhi.h>
#include <linux/i2c-gpio.h>
+#include <linux/reboot.h>
#include <mach/common.h>
#include <mach/irqs.h>
#include <mach/r8a7740.h>
static struct fixed_voltage_config vcc_sdhi0_info = {
.supply_name = "SDHI0 Vcc",
.microvolts = 3300000,
- .gpio = GPIO_PORT75,
+ .gpio = 75,
.enable_high = 1,
.init_data = &vcc_sdhi0_init_data,
};
};
static struct gpio vccq_sdhi0_gpios[] = {
- {GPIO_PORT17, GPIOF_OUT_INIT_LOW, "vccq-sdhi0" },
+ {17, GPIOF_OUT_INIT_LOW, "vccq-sdhi0" },
};
static struct gpio_regulator_state vccq_sdhi0_states[] = {
static struct gpio_regulator_config vccq_sdhi0_info = {
.supply_name = "vqmmc",
- .enable_gpio = GPIO_PORT74,
+ .enable_gpio = 74,
.enable_high = 1,
.enabled_at_boot = 0,
static struct fixed_voltage_config vcc_sdhi1_info = {
.supply_name = "SDHI1 Vcc",
.microvolts = 3300000,
- .gpio = GPIO_PORT16,
+ .gpio = 16,
.enable_high = 1,
.init_data = &vcc_sdhi1_init_data,
};
.tmio_caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |
MMC_CAP_POWER_OFF_CARD,
.tmio_flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
- .cd_gpio = GPIO_PORT167,
+ .cd_gpio = 167,
};
static struct resource sdhi0_resources[] = {
MMC_CAP_POWER_OFF_CARD,
.tmio_flags = TMIO_MMC_HAS_IDLE_WAIT | TMIO_MMC_USE_GPIO_CD,
/* Port72 cannot generate IRQs, will be used in polling mode. */
- .cd_gpio = GPIO_PORT72,
+ .cd_gpio = 72,
};
static struct resource sdhi1_resources[] = {
};
static const struct pinctrl_map eva_pinctrl_map[] = {
+ /* CEU0 */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
+ "ceu0_data_0_7", "ceu0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
+ "ceu0_clk_0", "ceu0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
+ "ceu0_sync", "ceu0"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_ceu.0", "pfc-r8a7740",
+ "ceu0_field", "ceu0"),
+ /* FSIA */
+ PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
+ "fsia_sclk_in", "fsia"),
+ PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
+ "fsia_mclk_out", "fsia"),
+ PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
+ "fsia_data_in_1", "fsia"),
+ PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.0", "pfc-r8a7740",
+ "fsia_data_out_0", "fsia"),
+ /* FSIB */
+ PIN_MAP_MUX_GROUP_DEFAULT("asoc-simple-card.1", "pfc-r8a7740",
+ "fsib_mclk_in", "fsib"),
+ /* GETHER */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh-eth", "pfc-r8a7740",
+ "gether_mii", "gether"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh-eth", "pfc-r8a7740",
+ "gether_int", "gether"),
+ /* HDMI */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh-mobile-hdmi", "pfc-r8a7740",
+ "hdmi", "hdmi"),
/* LCD0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_lcdc_fb.0", "pfc-r8a7740",
"lcd0_data24_0", "lcd0"),
"mmc0_data8_1", "mmc0"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif.0", "pfc-r8a7740",
"mmc0_ctrl_1", "mmc0"),
+ /* SCIFA1 */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.1", "pfc-r8a7740",
+ "scifa1_data", "scifa1"),
/* SDHI0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
"sdhi0_data4", "sdhi0"),
"sdhi0_ctrl", "sdhi0"),
PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7740",
"sdhi0_wp", "sdhi0"),
+ /* ST1232 */
+ PIN_MAP_MUX_GROUP_DEFAULT("0-0055", "pfc-r8a7740",
+ "intc_irq10", "intc"),
+ /* USBHS */
+ PIN_MAP_MUX_GROUP_DEFAULT("renesas_usbhs", "pfc-r8a7740",
+ "intc_irq7_1", "intc"),
};
static void __init eva_clock_init(void)
r8a7740_pinmux_init();
r8a7740_meram_workaround();
- /* SCIFA1 */
- gpio_request(GPIO_FN_SCIFA1_RXD, NULL);
- gpio_request(GPIO_FN_SCIFA1_TXD, NULL);
-
/* LCDC0 */
- gpio_request(GPIO_FN_LCDC0_SELECT, NULL);
-
gpio_request_one(61, GPIOF_OUT_INIT_HIGH, NULL); /* LCDDON */
gpio_request_one(202, GPIOF_OUT_INIT_LOW, NULL); /* LCD0_LED_CONT */
/* Touchscreen */
- gpio_request(GPIO_FN_IRQ10, NULL); /* TP_INT */
+ gpio_request_one(166, GPIOF_OUT_INIT_HIGH, NULL); /* TP_RST_B */
/* GETHER */
- gpio_request(GPIO_FN_ET_CRS, NULL);
- gpio_request(GPIO_FN_ET_MDC, NULL);
- gpio_request(GPIO_FN_ET_MDIO, NULL);
- gpio_request(GPIO_FN_ET_TX_ER, NULL);
- gpio_request(GPIO_FN_ET_RX_ER, NULL);
- gpio_request(GPIO_FN_ET_ERXD0, NULL);
- gpio_request(GPIO_FN_ET_ERXD1, NULL);
- gpio_request(GPIO_FN_ET_ERXD2, NULL);
- gpio_request(GPIO_FN_ET_ERXD3, NULL);
- gpio_request(GPIO_FN_ET_TX_CLK, NULL);
- gpio_request(GPIO_FN_ET_TX_EN, NULL);
- gpio_request(GPIO_FN_ET_ETXD0, NULL);
- gpio_request(GPIO_FN_ET_ETXD1, NULL);
- gpio_request(GPIO_FN_ET_ETXD2, NULL);
- gpio_request(GPIO_FN_ET_ETXD3, NULL);
- gpio_request(GPIO_FN_ET_PHY_INT, NULL);
- gpio_request(GPIO_FN_ET_COL, NULL);
- gpio_request(GPIO_FN_ET_RX_DV, NULL);
- gpio_request(GPIO_FN_ET_RX_CLK, NULL);
-
gpio_request_one(18, GPIOF_OUT_INIT_HIGH, NULL); /* PHY_RST */
/* USB */
} else {
/* USB Func */
/*
- * A1 chip has 2 IRQ7 pin and it was controled by MSEL register.
- * OTOH, usbhs interrupt needs its value (HI/LOW) to decide
- * USB connection/disconnection (usbhsf_get_vbus()).
- * This means we needs to select GPIO_FN_IRQ7_PORT209 first,
- * and select GPIO 209 here
+ * The USBHS interrupt handlers needs to read the IRQ pin value
+ * (HI/LOW) to diffentiate USB connection and disconnection
+ * events (usbhsf_get_vbus()). We thus need to select both the
+ * intc_irq7_1 pin group and GPIO 209 here.
*/
- gpio_request(GPIO_FN_IRQ7_PORT209, NULL);
gpio_request_one(209, GPIOF_IN, NULL);
platform_device_register(&usbhsf_device);
usb = &usbhsf_device;
}
- /* CEU0 */
- gpio_request(GPIO_FN_VIO0_D7, NULL);
- gpio_request(GPIO_FN_VIO0_D6, NULL);
- gpio_request(GPIO_FN_VIO0_D5, NULL);
- gpio_request(GPIO_FN_VIO0_D4, NULL);
- gpio_request(GPIO_FN_VIO0_D3, NULL);
- gpio_request(GPIO_FN_VIO0_D2, NULL);
- gpio_request(GPIO_FN_VIO0_D1, NULL);
- gpio_request(GPIO_FN_VIO0_D0, NULL);
- gpio_request(GPIO_FN_VIO0_CLK, NULL);
- gpio_request(GPIO_FN_VIO0_HD, NULL);
- gpio_request(GPIO_FN_VIO0_VD, NULL);
- gpio_request(GPIO_FN_VIO0_FIELD, NULL);
- gpio_request(GPIO_FN_VIO_CKO, NULL);
-
/* CON1/CON15 Camera */
gpio_request_one(173, GPIOF_OUT_INIT_LOW, NULL); /* STANDBY */
gpio_request_one(172, GPIOF_OUT_INIT_HIGH, NULL); /* RST */
gpio_request_one(158, GPIOF_OUT_INIT_LOW, NULL); /* CAM_PON */
/* FSI-WM8978 */
- gpio_request(GPIO_FN_FSIAIBT, NULL);
- gpio_request(GPIO_FN_FSIAILR, NULL);
- gpio_request(GPIO_FN_FSIAOMC, NULL);
- gpio_request(GPIO_FN_FSIAOSLD, NULL);
- gpio_request(GPIO_FN_FSIAISLD_PORT5, NULL);
-
gpio_request(7, NULL);
gpio_request(8, NULL);
gpio_direction_none(GPIO_PORT7CR); /* FSIAOBT needs no direction */
gpio_direction_none(GPIO_PORT8CR); /* FSIAOLR needs no direction */
- /* FSI-HDMI */
- gpio_request(GPIO_FN_FSIBCK, NULL);
-
- /* HDMI */
- gpio_request(GPIO_FN_HDMI_HPD, NULL);
- gpio_request(GPIO_FN_HDMI_CEC, NULL);
-
/*
* CAUTION
*
}
#define RESCNT2 IOMEM(0xe6188020)
-static void eva_restart(char mode, const char *cmd)
+static void eva_restart(enum reboot_mode mode, const char *cmd)
{
/* Do soft power on reset */
writel((1 << 31), RESCNT2);
projects / cascardo / linux.git / blobdiff