#include <drm/drm_panel.h>
#include <linux/clk.h>
+#include <linux/gpio/consumer.h>
#include <linux/irq.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
#include <linux/phy/phy.h>
#include <linux/regulator/consumer.h>
#include <linux/component.h>
#include <video/mipi_display.h>
#include <video/videomode.h>
+#include "exynos_drm_crtc.h"
#include "exynos_drm_drv.h"
/* returns true iff both arguments logically differs */
/* FIFO memory AC characteristic register */
#define DSIM_PLLCTRL_REG 0x4c /* PLL control register */
-#define DSIM_PLLTMR_REG 0x50 /* PLL timer register */
#define DSIM_PHYACCHR_REG 0x54 /* D-PHY AC characteristic register */
#define DSIM_PHYACCHR1_REG 0x58 /* D-PHY AC characteristic register1 */
+#define DSIM_PHYCTRL_REG 0x5c
+#define DSIM_PHYTIMING_REG 0x64
+#define DSIM_PHYTIMING1_REG 0x68
+#define DSIM_PHYTIMING2_REG 0x6c
/* DSIM_STATUS */
#define DSIM_STOP_STATE_DAT(x) (((x) & 0xf) << 0)
#define DSIM_PLL_M(x) ((x) << 4)
#define DSIM_PLL_S(x) ((x) << 1)
+/* DSIM_PHYCTRL */
+#define DSIM_PHYCTRL_ULPS_EXIT(x) (((x) & 0x1ff) << 0)
+
+/* DSIM_PHYTIMING */
+#define DSIM_PHYTIMING_LPX(x) ((x) << 8)
+#define DSIM_PHYTIMING_HS_EXIT(x) ((x) << 0)
+
+/* DSIM_PHYTIMING1 */
+#define DSIM_PHYTIMING1_CLK_PREPARE(x) ((x) << 24)
+#define DSIM_PHYTIMING1_CLK_ZERO(x) ((x) << 16)
+#define DSIM_PHYTIMING1_CLK_POST(x) ((x) << 8)
+#define DSIM_PHYTIMING1_CLK_TRAIL(x) ((x) << 0)
+
+/* DSIM_PHYTIMING2 */
+#define DSIM_PHYTIMING2_HS_PREPARE(x) ((x) << 16)
+#define DSIM_PHYTIMING2_HS_ZERO(x) ((x) << 8)
+#define DSIM_PHYTIMING2_HS_TRAIL(x) ((x) << 0)
+
#define DSI_MAX_BUS_WIDTH 4
#define DSI_NUM_VIRTUAL_CHANNELS 4
#define DSI_TX_FIFO_SIZE 2048
#define DSIM_STATE_INITIALIZED BIT(1)
#define DSIM_STATE_CMD_LPM BIT(2)
+struct exynos_dsi_driver_data {
+ unsigned int plltmr_reg;
+
+ unsigned int has_freqband:1;
+};
+
struct exynos_dsi {
struct mipi_dsi_host dsi_host;
struct drm_connector connector;
struct clk *bus_clk;
struct regulator_bulk_data supplies[2];
int irq;
+ int te_gpio;
u32 pll_clk_rate;
u32 burst_clk_rate;
spinlock_t transfer_lock; /* protects transfer_list */
struct list_head transfer_list;
+
+ struct exynos_dsi_driver_data *driver_data;
};
#define host_to_dsi(host) container_of(host, struct exynos_dsi, dsi_host)
#define connector_to_dsi(c) container_of(c, struct exynos_dsi, connector)
+static struct exynos_dsi_driver_data exynos4_dsi_driver_data = {
+ .plltmr_reg = 0x50,
+ .has_freqband = 1,
+};
+
+static struct exynos_dsi_driver_data exynos5_dsi_driver_data = {
+ .plltmr_reg = 0x58,
+};
+
+static struct of_device_id exynos_dsi_of_match[] = {
+ { .compatible = "samsung,exynos4210-mipi-dsi",
+ .data = &exynos4_dsi_driver_data },
+ { .compatible = "samsung,exynos5410-mipi-dsi",
+ .data = &exynos5_dsi_driver_data },
+ { }
+};
+
+static inline struct exynos_dsi_driver_data *exynos_dsi_get_driver_data(
+ struct platform_device *pdev)
+{
+ const struct of_device_id *of_id =
+ of_match_device(exynos_dsi_of_match, &pdev->dev);
+
+ return (struct exynos_dsi_driver_data *)of_id->data;
+}
+
static void exynos_dsi_wait_for_reset(struct exynos_dsi *dsi)
{
if (wait_for_completion_timeout(&dsi->completed, msecs_to_jiffies(300)))
static unsigned long exynos_dsi_set_pll(struct exynos_dsi *dsi,
unsigned long freq)
{
- static const unsigned long freq_bands[] = {
- 100 * MHZ, 120 * MHZ, 160 * MHZ, 200 * MHZ,
- 270 * MHZ, 320 * MHZ, 390 * MHZ, 450 * MHZ,
- 510 * MHZ, 560 * MHZ, 640 * MHZ, 690 * MHZ,
- 770 * MHZ, 870 * MHZ, 950 * MHZ,
- };
+ struct exynos_dsi_driver_data *driver_data = dsi->driver_data;
unsigned long fin, fout;
- int timeout, band;
+ int timeout;
u8 p, s;
u16 m;
u32 reg;
"failed to find PLL PMS for requested frequency\n");
return -EFAULT;
}
+ dev_dbg(dsi->dev, "PLL freq %lu, (p %d, m %d, s %d)\n", fout, p, m, s);
- for (band = 0; band < ARRAY_SIZE(freq_bands); ++band)
- if (fout < freq_bands[band])
- break;
+ writel(500, dsi->reg_base + driver_data->plltmr_reg);
+
+ reg = DSIM_PLL_EN | DSIM_PLL_P(p) | DSIM_PLL_M(m) | DSIM_PLL_S(s);
+
+ if (driver_data->has_freqband) {
+ static const unsigned long freq_bands[] = {
+ 100 * MHZ, 120 * MHZ, 160 * MHZ, 200 * MHZ,
+ 270 * MHZ, 320 * MHZ, 390 * MHZ, 450 * MHZ,
+ 510 * MHZ, 560 * MHZ, 640 * MHZ, 690 * MHZ,
+ 770 * MHZ, 870 * MHZ, 950 * MHZ,
+ };
+ int band;
- dev_dbg(dsi->dev, "PLL freq %lu, (p %d, m %d, s %d), band %d\n", fout,
- p, m, s, band);
+ for (band = 0; band < ARRAY_SIZE(freq_bands); ++band)
+ if (fout < freq_bands[band])
+ break;
- writel(500, dsi->reg_base + DSIM_PLLTMR_REG);
+ dev_dbg(dsi->dev, "band %d\n", band);
+
+ reg |= DSIM_FREQ_BAND(band);
+ }
- reg = DSIM_FREQ_BAND(band) | DSIM_PLL_EN
- | DSIM_PLL_P(p) | DSIM_PLL_M(m) | DSIM_PLL_S(s);
writel(reg, dsi->reg_base + DSIM_PLLCTRL_REG);
timeout = 1000;
return 0;
}
+static void exynos_dsi_set_phy_ctrl(struct exynos_dsi *dsi)
+{
+ struct exynos_dsi_driver_data *driver_data = dsi->driver_data;
+ u32 reg;
+
+ if (driver_data->has_freqband)
+ return;
+
+ /* B D-PHY: D-PHY Master & Slave Analog Block control */
+ reg = DSIM_PHYCTRL_ULPS_EXIT(0x0af);
+ writel(reg, dsi->reg_base + DSIM_PHYCTRL_REG);
+
+ /*
+ * T LPX: Transmitted length of any Low-Power state period
+ * T HS-EXIT: Time that the transmitter drives LP-11 following a HS
+ * burst
+ */
+ reg = DSIM_PHYTIMING_LPX(0x06) | DSIM_PHYTIMING_HS_EXIT(0x0b);
+ writel(reg, dsi->reg_base + DSIM_PHYTIMING_REG);
+
+ /*
+ * T CLK-PREPARE: Time that the transmitter drives the Clock Lane LP-00
+ * Line state immediately before the HS-0 Line state starting the
+ * HS transmission
+ * T CLK-ZERO: Time that the transmitter drives the HS-0 state prior to
+ * transmitting the Clock.
+ * T CLK_POST: Time that the transmitter continues to send HS clock
+ * after the last associated Data Lane has transitioned to LP Mode
+ * Interval is defined as the period from the end of T HS-TRAIL to
+ * the beginning of T CLK-TRAIL
+ * T CLK-TRAIL: Time that the transmitter drives the HS-0 state after
+ * the last payload clock bit of a HS transmission burst
+ */
+ reg = DSIM_PHYTIMING1_CLK_PREPARE(0x07) |
+ DSIM_PHYTIMING1_CLK_ZERO(0x27) |
+ DSIM_PHYTIMING1_CLK_POST(0x0d) |
+ DSIM_PHYTIMING1_CLK_TRAIL(0x08);
+ writel(reg, dsi->reg_base + DSIM_PHYTIMING1_REG);
+
+ /*
+ * T HS-PREPARE: Time that the transmitter drives the Data Lane LP-00
+ * Line state immediately before the HS-0 Line state starting the
+ * HS transmission
+ * T HS-ZERO: Time that the transmitter drives the HS-0 state prior to
+ * transmitting the Sync sequence.
+ * T HS-TRAIL: Time that the transmitter drives the flipped differential
+ * state after last payload data bit of a HS transmission burst
+ */
+ reg = DSIM_PHYTIMING2_HS_PREPARE(0x09) | DSIM_PHYTIMING2_HS_ZERO(0x0d) |
+ DSIM_PHYTIMING2_HS_TRAIL(0x0b);
+ writel(reg, dsi->reg_base + DSIM_PHYTIMING2_REG);
+}
+
static void exynos_dsi_disable_clock(struct exynos_dsi *dsi)
{
u32 reg;
/* DSI configuration */
reg = 0;
+ /*
+ * The first bit of mode_flags specifies display configuration.
+ * If this bit is set[= MIPI_DSI_MODE_VIDEO], dsi will support video
+ * mode, otherwise it will support command mode.
+ */
if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
reg |= DSIM_VIDEO_MODE;
+ /*
+ * The user manual describes that following bits are ignored in
+ * command mode.
+ */
if (!(dsi->mode_flags & MIPI_DSI_MODE_VSYNC_FLUSH))
reg |= DSIM_MFLUSH_VS;
- if (!(dsi->mode_flags & MIPI_DSI_MODE_EOT_PACKET))
- reg |= DSIM_EOT_DISABLE;
if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_SYNC_PULSE)
reg |= DSIM_SYNC_INFORM;
if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO_BURST)
reg |= DSIM_HSA_MODE;
}
+ if (!(dsi->mode_flags & MIPI_DSI_MODE_EOT_PACKET))
+ reg |= DSIM_EOT_DISABLE;
+
switch (dsi->format) {
case MIPI_DSI_FMT_RGB888:
reg |= DSIM_MAIN_PIX_FORMAT_RGB888;
return IRQ_HANDLED;
}
+static irqreturn_t exynos_dsi_te_irq_handler(int irq, void *dev_id)
+{
+ struct exynos_dsi *dsi = (struct exynos_dsi *)dev_id;
+ struct drm_encoder *encoder = dsi->encoder;
+
+ if (dsi->state & DSIM_STATE_ENABLED)
+ exynos_drm_crtc_te_handler(encoder->crtc);
+
+ return IRQ_HANDLED;
+}
+
+static void exynos_dsi_enable_irq(struct exynos_dsi *dsi)
+{
+ enable_irq(dsi->irq);
+
+ if (gpio_is_valid(dsi->te_gpio))
+ enable_irq(gpio_to_irq(dsi->te_gpio));
+}
+
+static void exynos_dsi_disable_irq(struct exynos_dsi *dsi)
+{
+ if (gpio_is_valid(dsi->te_gpio))
+ disable_irq(gpio_to_irq(dsi->te_gpio));
+
+ disable_irq(dsi->irq);
+}
+
static int exynos_dsi_init(struct exynos_dsi *dsi)
{
- exynos_dsi_enable_clock(dsi);
exynos_dsi_reset(dsi);
- enable_irq(dsi->irq);
+ exynos_dsi_enable_irq(dsi);
+ exynos_dsi_enable_clock(dsi);
exynos_dsi_wait_for_reset(dsi);
+ exynos_dsi_set_phy_ctrl(dsi);
exynos_dsi_init_link(dsi);
return 0;
}
+static int exynos_dsi_register_te_irq(struct exynos_dsi *dsi)
+{
+ int ret;
+
+ dsi->te_gpio = of_get_named_gpio(dsi->panel_node, "te-gpios", 0);
+ if (!gpio_is_valid(dsi->te_gpio)) {
+ dev_err(dsi->dev, "no te-gpios specified\n");
+ ret = dsi->te_gpio;
+ goto out;
+ }
+
+ ret = gpio_request_one(dsi->te_gpio, GPIOF_IN, "te_gpio");
+ if (ret) {
+ dev_err(dsi->dev, "gpio request failed with %d\n", ret);
+ goto out;
+ }
+
+ /*
+ * This TE GPIO IRQ should not be set to IRQ_NOAUTOEN, because panel
+ * calls drm_panel_init() first then calls mipi_dsi_attach() in probe().
+ * It means that te_gpio is invalid when exynos_dsi_enable_irq() is
+ * called by drm_panel_init() before panel is attached.
+ */
+ ret = request_threaded_irq(gpio_to_irq(dsi->te_gpio),
+ exynos_dsi_te_irq_handler, NULL,
+ IRQF_TRIGGER_RISING, "TE", dsi);
+ if (ret) {
+ dev_err(dsi->dev, "request interrupt failed with %d\n", ret);
+ gpio_free(dsi->te_gpio);
+ goto out;
+ }
+
+out:
+ return ret;
+}
+
+static void exynos_dsi_unregister_te_irq(struct exynos_dsi *dsi)
+{
+ if (gpio_is_valid(dsi->te_gpio)) {
+ free_irq(gpio_to_irq(dsi->te_gpio), dsi);
+ gpio_free(dsi->te_gpio);
+ dsi->te_gpio = -ENOENT;
+ }
+}
+
static int exynos_dsi_host_attach(struct mipi_dsi_host *host,
struct mipi_dsi_device *device)
{
if (dsi->connector.dev)
drm_helper_hpd_irq_event(dsi->connector.dev);
+ /*
+ * This is a temporary solution and should be made by more generic way.
+ *
+ * If attached panel device is for command mode one, dsi should register
+ * TE interrupt handler.
+ */
+ if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) {
+ int ret = exynos_dsi_register_te_irq(dsi);
+
+ if (ret)
+ return ret;
+ }
+
return 0;
}
{
struct exynos_dsi *dsi = host_to_dsi(host);
+ exynos_dsi_unregister_te_irq(dsi);
+
dsi->panel_node = NULL;
if (dsi->connector.dev)
exynos_dsi_disable_clock(dsi);
- disable_irq(dsi->irq);
+ exynos_dsi_disable_irq(dsi);
}
dsi->state &= ~DSIM_STATE_CMD_LPM;
}
drm_connector_helper_add(connector, &exynos_dsi_connector_helper_funcs);
- drm_sysfs_connector_add(connector);
+ drm_connector_register(connector);
drm_mode_connector_attach_encoder(connector, encoder);
return 0;
.type = EXYNOS_DISPLAY_TYPE_LCD,
.ops = &exynos_dsi_display_ops,
};
+MODULE_DEVICE_TABLE(of, exynos_dsi_of_match);
/* of_* functions will be removed after merge of of_graph patches */
static struct device_node *
goto err_del_component;
}
+ /* To be checked as invalid one */
+ dsi->te_gpio = -ENOENT;
+
init_completion(&dsi->completed);
spin_lock_init(&dsi->transfer_lock);
INIT_LIST_HEAD(&dsi->transfer_list);
dsi->dsi_host.dev = &pdev->dev;
dsi->dev = &pdev->dev;
+ dsi->driver_data = exynos_dsi_get_driver_data(pdev);
ret = exynos_dsi_parse_dt(dsi);
if (ret)
return 0;
}
-static struct of_device_id exynos_dsi_of_match[] = {
- { .compatible = "samsung,exynos4210-mipi-dsi" },
- { }
-};
-
struct platform_driver dsi_driver = {
.probe = exynos_dsi_probe,
.remove = exynos_dsi_remove,
projects / cascardo / linux.git / blobdiff