/*
* Linux ARCnet driver - "raw mode" packet encapsulation (no soft headers)
- *
+ *
* Written 1994-1999 by Avery Pennarun.
* Derived from skeleton.c by Donald Becker.
*
#define VERSION "arcnet: raw mode (`r') encapsulation support loaded.\n"
-
static void rx(struct net_device *dev, int bufnum,
struct archdr *pkthdr, int length);
static int build_header(struct sk_buff *skb, struct net_device *dev,
static int prepare_tx(struct net_device *dev, struct archdr *pkt, int length,
int bufnum);
-static struct ArcProto rawmode_proto =
-{
+static struct ArcProto rawmode_proto = {
.suffix = 'r',
.mtu = XMTU,
.rx = rx,
.ack_tx = NULL
};
-
static int __init arcnet_raw_init(void)
{
int count;
MODULE_LICENSE("GPL");
-
/* packet receiver */
static void rx(struct net_device *dev, int bufnum,
struct archdr *pkthdr, int length)
skb_put(skb, length + ARC_HDR_SIZE);
skb->dev = dev;
- pkt = (struct archdr *) skb->data;
+ pkt = (struct archdr *)skb->data;
skb_reset_mac_header(skb);
skb_pull(skb, ARC_HDR_SIZE);
pkt->soft.raw + sizeof(pkt->soft),
length - sizeof(pkt->soft));
- BUGLVL(D_SKB) arcnet_dump_skb(dev, skb, "rx");
+ if (BUGLVL(D_SKB))
+ arcnet_dump_skb(dev, skb, "rx");
skb->protocol = cpu_to_be16(ETH_P_ARCNET);
netif_rx(skb);
}
-
-/*
- * Create the ARCnet hard/soft headers for raw mode.
+/* Create the ARCnet hard/soft headers for raw mode.
* There aren't any soft headers in raw mode - not even the protocol id.
*/
static int build_header(struct sk_buff *skb, struct net_device *dev,
unsigned short type, uint8_t daddr)
{
int hdr_size = ARC_HDR_SIZE;
- struct archdr *pkt = (struct archdr *) skb_push(skb, hdr_size);
+ struct archdr *pkt = (struct archdr *)skb_push(skb, hdr_size);
- /*
- * Set the source hardware address.
+ /* Set the source hardware address.
*
* This is pretty pointless for most purposes, but it can help in
- * debugging. ARCnet does not allow us to change the source address in
- * the actual packet sent)
+ * debugging. ARCnet does not allow us to change the source address
+ * in the actual packet sent.
*/
pkt->hard.source = *dev->dev_addr;
/* see linux/net/ethernet/eth.c to see where I got the following */
if (dev->flags & (IFF_LOOPBACK | IFF_NOARP)) {
- /*
- * FIXME: fill in the last byte of the dest ipaddr here to better
- * comply with RFC1051 in "noarp" mode.
+ /* FIXME: fill in the last byte of the dest ipaddr here
+ * to better comply with RFC1051 in "noarp" mode.
*/
pkt->hard.dest = 0;
return hdr_size;
return hdr_size; /* success */
}
-
static int prepare_tx(struct net_device *dev, struct archdr *pkt, int length,
int bufnum)
{
} else if (length > MTU) {
hard->offset[0] = 0;
hard->offset[1] = ofs = 512 - length - 3;
- } else
+ } else {
hard->offset[0] = ofs = 256 - length;
+ }
BUGMSG(D_DURING, "prepare_tx: length=%d ofs=%d\n",
- length,ofs);
+ length, ofs);
lp->hw.copy_to_card(dev, bufnum, 0, hard, ARC_HDR_SIZE);
lp->hw.copy_to_card(dev, bufnum, ofs, &pkt->soft, length);