(c_macaddr)[5] = (((pwmi_mac_addr)->word1) >> 8) & 0xff; \
} while (0)
+struct wmi_cmd_map {
+ u32 init_cmdid;
+ u32 start_scan_cmdid;
+ u32 stop_scan_cmdid;
+ u32 scan_chan_list_cmdid;
+ u32 scan_sch_prio_tbl_cmdid;
+ u32 pdev_set_regdomain_cmdid;
+ u32 pdev_set_channel_cmdid;
+ u32 pdev_set_param_cmdid;
+ u32 pdev_pktlog_enable_cmdid;
+ u32 pdev_pktlog_disable_cmdid;
+ u32 pdev_set_wmm_params_cmdid;
+ u32 pdev_set_ht_cap_ie_cmdid;
+ u32 pdev_set_vht_cap_ie_cmdid;
+ u32 pdev_set_dscp_tid_map_cmdid;
+ u32 pdev_set_quiet_mode_cmdid;
+ u32 pdev_green_ap_ps_enable_cmdid;
+ u32 pdev_get_tpc_config_cmdid;
+ u32 pdev_set_base_macaddr_cmdid;
+ u32 vdev_create_cmdid;
+ u32 vdev_delete_cmdid;
+ u32 vdev_start_request_cmdid;
+ u32 vdev_restart_request_cmdid;
+ u32 vdev_up_cmdid;
+ u32 vdev_stop_cmdid;
+ u32 vdev_down_cmdid;
+ u32 vdev_set_param_cmdid;
+ u32 vdev_install_key_cmdid;
+ u32 peer_create_cmdid;
+ u32 peer_delete_cmdid;
+ u32 peer_flush_tids_cmdid;
+ u32 peer_set_param_cmdid;
+ u32 peer_assoc_cmdid;
+ u32 peer_add_wds_entry_cmdid;
+ u32 peer_remove_wds_entry_cmdid;
+ u32 peer_mcast_group_cmdid;
+ u32 bcn_tx_cmdid;
+ u32 pdev_send_bcn_cmdid;
+ u32 bcn_tmpl_cmdid;
+ u32 bcn_filter_rx_cmdid;
+ u32 prb_req_filter_rx_cmdid;
+ u32 mgmt_tx_cmdid;
+ u32 prb_tmpl_cmdid;
+ u32 addba_clear_resp_cmdid;
+ u32 addba_send_cmdid;
+ u32 addba_status_cmdid;
+ u32 delba_send_cmdid;
+ u32 addba_set_resp_cmdid;
+ u32 send_singleamsdu_cmdid;
+ u32 sta_powersave_mode_cmdid;
+ u32 sta_powersave_param_cmdid;
+ u32 sta_mimo_ps_mode_cmdid;
+ u32 pdev_dfs_enable_cmdid;
+ u32 pdev_dfs_disable_cmdid;
+ u32 roam_scan_mode;
+ u32 roam_scan_rssi_threshold;
+ u32 roam_scan_period;
+ u32 roam_scan_rssi_change_threshold;
+ u32 roam_ap_profile;
+ u32 ofl_scan_add_ap_profile;
+ u32 ofl_scan_remove_ap_profile;
+ u32 ofl_scan_period;
+ u32 p2p_dev_set_device_info;
+ u32 p2p_dev_set_discoverability;
+ u32 p2p_go_set_beacon_ie;
+ u32 p2p_go_set_probe_resp_ie;
+ u32 p2p_set_vendor_ie_data_cmdid;
+ u32 ap_ps_peer_param_cmdid;
+ u32 ap_ps_peer_uapsd_coex_cmdid;
+ u32 peer_rate_retry_sched_cmdid;
+ u32 wlan_profile_trigger_cmdid;
+ u32 wlan_profile_set_hist_intvl_cmdid;
+ u32 wlan_profile_get_profile_data_cmdid;
+ u32 wlan_profile_enable_profile_id_cmdid;
+ u32 wlan_profile_list_profile_id_cmdid;
+ u32 pdev_suspend_cmdid;
+ u32 pdev_resume_cmdid;
+ u32 add_bcn_filter_cmdid;
+ u32 rmv_bcn_filter_cmdid;
+ u32 wow_add_wake_pattern_cmdid;
+ u32 wow_del_wake_pattern_cmdid;
+ u32 wow_enable_disable_wake_event_cmdid;
+ u32 wow_enable_cmdid;
+ u32 wow_hostwakeup_from_sleep_cmdid;
+ u32 rtt_measreq_cmdid;
+ u32 rtt_tsf_cmdid;
+ u32 vdev_spectral_scan_configure_cmdid;
+ u32 vdev_spectral_scan_enable_cmdid;
+ u32 request_stats_cmdid;
+ u32 set_arp_ns_offload_cmdid;
+ u32 network_list_offload_config_cmdid;
+ u32 gtk_offload_cmdid;
+ u32 csa_offload_enable_cmdid;
+ u32 csa_offload_chanswitch_cmdid;
+ u32 chatter_set_mode_cmdid;
+ u32 peer_tid_addba_cmdid;
+ u32 peer_tid_delba_cmdid;
+ u32 sta_dtim_ps_method_cmdid;
+ u32 sta_uapsd_auto_trig_cmdid;
+ u32 sta_keepalive_cmd;
+ u32 echo_cmdid;
+ u32 pdev_utf_cmdid;
+ u32 dbglog_cfg_cmdid;
+ u32 pdev_qvit_cmdid;
+ u32 pdev_ftm_intg_cmdid;
+ u32 vdev_set_keepalive_cmdid;
+ u32 vdev_get_keepalive_cmdid;
+ u32 force_fw_hang_cmdid;
+ u32 gpio_config_cmdid;
+ u32 gpio_output_cmdid;
+};
+
/*
* wmi command groups.
*/
#define WMI_CMD_GRP(grp_id) (((grp_id) << 12) | 0x1)
#define WMI_EVT_GRP_START_ID(grp_id) (((grp_id) << 12) | 0x1)
-/* Command IDs and commande events. */
+#define WMI_CMD_UNDEFINED 0
+
+/* Command IDs and command events for MAIN FW. */
enum wmi_cmd_id {
WMI_INIT_CMDID = 0x1,
WMI_GPIO_INPUT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_GPIO),
};
+/* Command IDs and command events for 10.X firmware */
+enum wmi_10x_cmd_id {
+ WMI_10X_START_CMDID = 0x9000,
+ WMI_10X_END_CMDID = 0x9FFF,
+
+ /* initialize the wlan sub system */
+ WMI_10X_INIT_CMDID,
+
+ /* Scan specific commands */
+
+ WMI_10X_START_SCAN_CMDID = WMI_10X_START_CMDID,
+ WMI_10X_STOP_SCAN_CMDID,
+ WMI_10X_SCAN_CHAN_LIST_CMDID,
+ WMI_10X_ECHO_CMDID,
+
+ /* PDEV(physical device) specific commands */
+ WMI_10X_PDEV_SET_REGDOMAIN_CMDID,
+ WMI_10X_PDEV_SET_CHANNEL_CMDID,
+ WMI_10X_PDEV_SET_PARAM_CMDID,
+ WMI_10X_PDEV_PKTLOG_ENABLE_CMDID,
+ WMI_10X_PDEV_PKTLOG_DISABLE_CMDID,
+ WMI_10X_PDEV_SET_WMM_PARAMS_CMDID,
+ WMI_10X_PDEV_SET_HT_CAP_IE_CMDID,
+ WMI_10X_PDEV_SET_VHT_CAP_IE_CMDID,
+ WMI_10X_PDEV_SET_BASE_MACADDR_CMDID,
+ WMI_10X_PDEV_SET_DSCP_TID_MAP_CMDID,
+ WMI_10X_PDEV_SET_QUIET_MODE_CMDID,
+ WMI_10X_PDEV_GREEN_AP_PS_ENABLE_CMDID,
+ WMI_10X_PDEV_GET_TPC_CONFIG_CMDID,
+
+ /* VDEV(virtual device) specific commands */
+ WMI_10X_VDEV_CREATE_CMDID,
+ WMI_10X_VDEV_DELETE_CMDID,
+ WMI_10X_VDEV_START_REQUEST_CMDID,
+ WMI_10X_VDEV_RESTART_REQUEST_CMDID,
+ WMI_10X_VDEV_UP_CMDID,
+ WMI_10X_VDEV_STOP_CMDID,
+ WMI_10X_VDEV_DOWN_CMDID,
+ WMI_10X_VDEV_STANDBY_RESPONSE_CMDID,
+ WMI_10X_VDEV_RESUME_RESPONSE_CMDID,
+ WMI_10X_VDEV_SET_PARAM_CMDID,
+ WMI_10X_VDEV_INSTALL_KEY_CMDID,
+
+ /* peer specific commands */
+ WMI_10X_PEER_CREATE_CMDID,
+ WMI_10X_PEER_DELETE_CMDID,
+ WMI_10X_PEER_FLUSH_TIDS_CMDID,
+ WMI_10X_PEER_SET_PARAM_CMDID,
+ WMI_10X_PEER_ASSOC_CMDID,
+ WMI_10X_PEER_ADD_WDS_ENTRY_CMDID,
+ WMI_10X_PEER_REMOVE_WDS_ENTRY_CMDID,
+ WMI_10X_PEER_MCAST_GROUP_CMDID,
+
+ /* beacon/management specific commands */
+
+ WMI_10X_BCN_TX_CMDID,
+ WMI_10X_BCN_PRB_TMPL_CMDID,
+ WMI_10X_BCN_FILTER_RX_CMDID,
+ WMI_10X_PRB_REQ_FILTER_RX_CMDID,
+ WMI_10X_MGMT_TX_CMDID,
+
+ /* commands to directly control ba negotiation directly from host. */
+ WMI_10X_ADDBA_CLEAR_RESP_CMDID,
+ WMI_10X_ADDBA_SEND_CMDID,
+ WMI_10X_ADDBA_STATUS_CMDID,
+ WMI_10X_DELBA_SEND_CMDID,
+ WMI_10X_ADDBA_SET_RESP_CMDID,
+ WMI_10X_SEND_SINGLEAMSDU_CMDID,
+
+ /* Station power save specific config */
+ WMI_10X_STA_POWERSAVE_MODE_CMDID,
+ WMI_10X_STA_POWERSAVE_PARAM_CMDID,
+ WMI_10X_STA_MIMO_PS_MODE_CMDID,
+
+ /* set debug log config */
+ WMI_10X_DBGLOG_CFG_CMDID,
+
+ /* DFS-specific commands */
+ WMI_10X_PDEV_DFS_ENABLE_CMDID,
+ WMI_10X_PDEV_DFS_DISABLE_CMDID,
+
+ /* QVIT specific command id */
+ WMI_10X_PDEV_QVIT_CMDID,
+
+ /* Offload Scan and Roaming related commands */
+ WMI_10X_ROAM_SCAN_MODE,
+ WMI_10X_ROAM_SCAN_RSSI_THRESHOLD,
+ WMI_10X_ROAM_SCAN_PERIOD,
+ WMI_10X_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
+ WMI_10X_ROAM_AP_PROFILE,
+ WMI_10X_OFL_SCAN_ADD_AP_PROFILE,
+ WMI_10X_OFL_SCAN_REMOVE_AP_PROFILE,
+ WMI_10X_OFL_SCAN_PERIOD,
+
+ /* P2P specific commands */
+ WMI_10X_P2P_DEV_SET_DEVICE_INFO,
+ WMI_10X_P2P_DEV_SET_DISCOVERABILITY,
+ WMI_10X_P2P_GO_SET_BEACON_IE,
+ WMI_10X_P2P_GO_SET_PROBE_RESP_IE,
+
+ /* AP power save specific config */
+ WMI_10X_AP_PS_PEER_PARAM_CMDID,
+ WMI_10X_AP_PS_PEER_UAPSD_COEX_CMDID,
+
+ /* Rate-control specific commands */
+ WMI_10X_PEER_RATE_RETRY_SCHED_CMDID,
+
+ /* WLAN Profiling commands. */
+ WMI_10X_WLAN_PROFILE_TRIGGER_CMDID,
+ WMI_10X_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
+ WMI_10X_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
+ WMI_10X_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
+ WMI_10X_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
+
+ /* Suspend resume command Ids */
+ WMI_10X_PDEV_SUSPEND_CMDID,
+ WMI_10X_PDEV_RESUME_CMDID,
+
+ /* Beacon filter commands */
+ WMI_10X_ADD_BCN_FILTER_CMDID,
+ WMI_10X_RMV_BCN_FILTER_CMDID,
+
+ /* WOW Specific WMI commands*/
+ WMI_10X_WOW_ADD_WAKE_PATTERN_CMDID,
+ WMI_10X_WOW_DEL_WAKE_PATTERN_CMDID,
+ WMI_10X_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
+ WMI_10X_WOW_ENABLE_CMDID,
+ WMI_10X_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
+
+ /* RTT measurement related cmd */
+ WMI_10X_RTT_MEASREQ_CMDID,
+ WMI_10X_RTT_TSF_CMDID,
+
+ /* transmit beacon by value */
+ WMI_10X_PDEV_SEND_BCN_CMDID,
+
+ /* F/W stats */
+ WMI_10X_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
+ WMI_10X_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
+ WMI_10X_REQUEST_STATS_CMDID,
+
+ /* GPIO Configuration */
+ WMI_10X_GPIO_CONFIG_CMDID,
+ WMI_10X_GPIO_OUTPUT_CMDID,
+
+ WMI_10X_PDEV_UTF_CMDID = WMI_10X_END_CMDID - 1,
+};
+
+enum wmi_10x_event_id {
+ WMI_10X_SERVICE_READY_EVENTID = 0x8000,
+ WMI_10X_READY_EVENTID,
+ WMI_10X_START_EVENTID = 0x9000,
+ WMI_10X_END_EVENTID = 0x9FFF,
+
+ /* Scan specific events */
+ WMI_10X_SCAN_EVENTID = WMI_10X_START_EVENTID,
+ WMI_10X_ECHO_EVENTID,
+ WMI_10X_DEBUG_MESG_EVENTID,
+ WMI_10X_UPDATE_STATS_EVENTID,
+
+ /* Instantaneous RSSI event */
+ WMI_10X_INST_RSSI_STATS_EVENTID,
+
+ /* VDEV specific events */
+ WMI_10X_VDEV_START_RESP_EVENTID,
+ WMI_10X_VDEV_STANDBY_REQ_EVENTID,
+ WMI_10X_VDEV_RESUME_REQ_EVENTID,
+ WMI_10X_VDEV_STOPPED_EVENTID,
+
+ /* peer specific events */
+ WMI_10X_PEER_STA_KICKOUT_EVENTID,
+
+ /* beacon/mgmt specific events */
+ WMI_10X_HOST_SWBA_EVENTID,
+ WMI_10X_TBTTOFFSET_UPDATE_EVENTID,
+ WMI_10X_MGMT_RX_EVENTID,
+
+ /* Channel stats event */
+ WMI_10X_CHAN_INFO_EVENTID,
+
+ /* PHY Error specific WMI event */
+ WMI_10X_PHYERR_EVENTID,
+
+ /* Roam event to trigger roaming on host */
+ WMI_10X_ROAM_EVENTID,
+
+ /* matching AP found from list of profiles */
+ WMI_10X_PROFILE_MATCH,
+
+ /* debug print message used for tracing FW code while debugging */
+ WMI_10X_DEBUG_PRINT_EVENTID,
+ /* VI spoecific event */
+ WMI_10X_PDEV_QVIT_EVENTID,
+ /* FW code profile data in response to profile request */
+ WMI_10X_WLAN_PROFILE_DATA_EVENTID,
+
+ /*RTT related event ID*/
+ WMI_10X_RTT_MEASUREMENT_REPORT_EVENTID,
+ WMI_10X_TSF_MEASUREMENT_REPORT_EVENTID,
+ WMI_10X_RTT_ERROR_REPORT_EVENTID,
+
+ WMI_10X_WOW_WAKEUP_HOST_EVENTID,
+ WMI_10X_DCS_INTERFERENCE_EVENTID,
+
+ /* TPC config for the current operating channel */
+ WMI_10X_PDEV_TPC_CONFIG_EVENTID,
+
+ WMI_10X_GPIO_INPUT_EVENTID,
+ WMI_10X_PDEV_UTF_EVENTID = WMI_10X_END_EVENTID-1,
+};
+
enum wmi_phy_mode {
MODE_11A = 0, /* 11a Mode */
MODE_11G = 1, /* 11b/g Mode */
MODE_MAX = 14
};
+static inline const char *ath10k_wmi_phymode_str(enum wmi_phy_mode mode)
+{
+ switch (mode) {
+ case MODE_11A:
+ return "11a";
+ case MODE_11G:
+ return "11g";
+ case MODE_11B:
+ return "11b";
+ case MODE_11GONLY:
+ return "11gonly";
+ case MODE_11NA_HT20:
+ return "11na-ht20";
+ case MODE_11NG_HT20:
+ return "11ng-ht20";
+ case MODE_11NA_HT40:
+ return "11na-ht40";
+ case MODE_11NG_HT40:
+ return "11ng-ht40";
+ case MODE_11AC_VHT20:
+ return "11ac-vht20";
+ case MODE_11AC_VHT40:
+ return "11ac-vht40";
+ case MODE_11AC_VHT80:
+ return "11ac-vht80";
+ case MODE_11AC_VHT20_2G:
+ return "11ac-vht20-2g";
+ case MODE_11AC_VHT40_2G:
+ return "11ac-vht40-2g";
+ case MODE_11AC_VHT80_2G:
+ return "11ac-vht80-2g";
+ case MODE_UNKNOWN:
+ /* skip */
+ break;
+
+ /* no default handler to allow compiler to check that the
+ * enum is fully handled */
+ };
+
+ return "<unknown>";
+}
+
#define WMI_CHAN_LIST_TAG 0x1
#define WMI_SSID_LIST_TAG 0x2
#define WMI_BSSID_LIST_TAG 0x3
struct wlan_host_mem_req mem_reqs[1];
} __packed;
+/* This is the definition from 10.X firmware branch */
+struct wmi_service_ready_event_10x {
+ __le32 sw_version;
+ __le32 abi_version;
+
+ /* WMI_PHY_CAPABILITY */
+ __le32 phy_capability;
+
+ /* Maximum number of frag table entries that SW will populate less 1 */
+ __le32 max_frag_entry;
+ __le32 wmi_service_bitmap[WMI_SERVICE_BM_SIZE];
+ __le32 num_rf_chains;
+
+ /*
+ * The following field is only valid for service type
+ * WMI_SERVICE_11AC
+ */
+ __le32 ht_cap_info; /* WMI HT Capability */
+ __le32 vht_cap_info; /* VHT capability info field of 802.11ac */
+ __le32 vht_supp_mcs; /* VHT Supported MCS Set field Rx/Tx same */
+ __le32 hw_min_tx_power;
+ __le32 hw_max_tx_power;
+
+ struct hal_reg_capabilities hal_reg_capabilities;
+
+ __le32 sys_cap_info;
+ __le32 min_pkt_size_enable; /* Enterprise mode short pkt enable */
+
+ /*
+ * request to host to allocate a chuck of memory and pss it down to FW
+ * via WM_INIT. FW uses this as FW extesnsion memory for saving its
+ * data structures. Only valid for low latency interfaces like PCIE
+ * where FW can access this memory directly (or) by DMA.
+ */
+ __le32 num_mem_reqs;
+
+ struct wlan_host_mem_req mem_reqs[1];
+} __packed;
+
+
#define WMI_SERVICE_READY_TIMEOUT_HZ (5*HZ)
#define WMI_UNIFIED_READY_TIMEOUT_HZ (5*HZ)
__le32 max_frag_entries;
} __packed;
+struct wmi_resource_config_10x {
+ /* number of virtual devices (VAPs) to support */
+ __le32 num_vdevs;
+
+ /* number of peer nodes to support */
+ __le32 num_peers;
+
+ /* number of keys per peer */
+ __le32 num_peer_keys;
+
+ /* total number of TX/RX data TIDs */
+ __le32 num_tids;
+
+ /*
+ * max skid for resolving hash collisions
+ *
+ * The address search table is sparse, so that if two MAC addresses
+ * result in the same hash value, the second of these conflicting
+ * entries can slide to the next index in the address search table,
+ * and use it, if it is unoccupied. This ast_skid_limit parameter
+ * specifies the upper bound on how many subsequent indices to search
+ * over to find an unoccupied space.
+ */
+ __le32 ast_skid_limit;
+
+ /*
+ * the nominal chain mask for transmit
+ *
+ * The chain mask may be modified dynamically, e.g. to operate AP
+ * tx with a reduced number of chains if no clients are associated.
+ * This configuration parameter specifies the nominal chain-mask that
+ * should be used when not operating with a reduced set of tx chains.
+ */
+ __le32 tx_chain_mask;
+
+ /*
+ * the nominal chain mask for receive
+ *
+ * The chain mask may be modified dynamically, e.g. for a client
+ * to use a reduced number of chains for receive if the traffic to
+ * the client is low enough that it doesn't require downlink MIMO
+ * or antenna diversity.
+ * This configuration parameter specifies the nominal chain-mask that
+ * should be used when not operating with a reduced set of rx chains.
+ */
+ __le32 rx_chain_mask;
+
+ /*
+ * what rx reorder timeout (ms) to use for the AC
+ *
+ * Each WMM access class (voice, video, best-effort, background) will
+ * have its own timeout value to dictate how long to wait for missing
+ * rx MPDUs to arrive before flushing subsequent MPDUs that have
+ * already been received.
+ * This parameter specifies the timeout in milliseconds for each
+ * class.
+ */
+ __le32 rx_timeout_pri_vi;
+ __le32 rx_timeout_pri_vo;
+ __le32 rx_timeout_pri_be;
+ __le32 rx_timeout_pri_bk;
+
+ /*
+ * what mode the rx should decap packets to
+ *
+ * MAC can decap to RAW (no decap), native wifi or Ethernet types
+ * THis setting also determines the default TX behavior, however TX
+ * behavior can be modified on a per VAP basis during VAP init
+ */
+ __le32 rx_decap_mode;
+
+ /* what is the maximum scan requests than can be queued */
+ __le32 scan_max_pending_reqs;
+
+ /* maximum VDEV that could use BMISS offload */
+ __le32 bmiss_offload_max_vdev;
+
+ /* maximum VDEV that could use offload roaming */
+ __le32 roam_offload_max_vdev;
+
+ /* maximum AP profiles that would push to offload roaming */
+ __le32 roam_offload_max_ap_profiles;
+
+ /*
+ * how many groups to use for mcast->ucast conversion
+ *
+ * The target's WAL maintains a table to hold information regarding
+ * which peers belong to a given multicast group, so that if
+ * multicast->unicast conversion is enabled, the target can convert
+ * multicast tx frames to a series of unicast tx frames, to each
+ * peer within the multicast group.
+ This num_mcast_groups configuration parameter tells the target how
+ * many multicast groups to provide storage for within its multicast
+ * group membership table.
+ */
+ __le32 num_mcast_groups;
+
+ /*
+ * size to alloc for the mcast membership table
+ *
+ * This num_mcast_table_elems configuration parameter tells the
+ * target how many peer elements it needs to provide storage for in
+ * its multicast group membership table.
+ * These multicast group membership table elements are shared by the
+ * multicast groups stored within the table.
+ */
+ __le32 num_mcast_table_elems;
+
+ /*
+ * whether/how to do multicast->unicast conversion
+ *
+ * This configuration parameter specifies whether the target should
+ * perform multicast --> unicast conversion on transmit, and if so,
+ * what to do if it finds no entries in its multicast group
+ * membership table for the multicast IP address in the tx frame.
+ * Configuration value:
+ * 0 -> Do not perform multicast to unicast conversion.
+ * 1 -> Convert multicast frames to unicast, if the IP multicast
+ * address from the tx frame is found in the multicast group
+ * membership table. If the IP multicast address is not found,
+ * drop the frame.
+ * 2 -> Convert multicast frames to unicast, if the IP multicast
+ * address from the tx frame is found in the multicast group
+ * membership table. If the IP multicast address is not found,
+ * transmit the frame as multicast.
+ */
+ __le32 mcast2ucast_mode;
+
+ /*
+ * how much memory to allocate for a tx PPDU dbg log
+ *
+ * This parameter controls how much memory the target will allocate
+ * to store a log of tx PPDU meta-information (how large the PPDU
+ * was, when it was sent, whether it was successful, etc.)
+ */
+ __le32 tx_dbg_log_size;
+
+ /* how many AST entries to be allocated for WDS */
+ __le32 num_wds_entries;
+
+ /*
+ * MAC DMA burst size, e.g., For target PCI limit can be
+ * 0 -default, 1 256B
+ */
+ __le32 dma_burst_size;
+
+ /*
+ * Fixed delimiters to be inserted after every MPDU to
+ * account for interface latency to avoid underrun.
+ */
+ __le32 mac_aggr_delim;
+
+ /*
+ * determine whether target is responsible for detecting duplicate
+ * non-aggregate MPDU and timing out stale fragments.
+ *
+ * A-MPDU reordering is always performed on the target.
+ *
+ * 0: target responsible for frag timeout and dup checking
+ * 1: host responsible for frag timeout and dup checking
+ */
+ __le32 rx_skip_defrag_timeout_dup_detection_check;
+
+ /*
+ * Configuration for VoW :
+ * No of Video Nodes to be supported
+ * and Max no of descriptors for each Video link (node).
+ */
+ __le32 vow_config;
+
+ /* Number of msdu descriptors target should use */
+ __le32 num_msdu_desc;
+
+ /*
+ * Max. number of Tx fragments per MSDU
+ * This parameter controls the max number of Tx fragments per MSDU.
+ * This is sent by the target as part of the WMI_SERVICE_READY event
+ * and is overriden by the OS shim as required.
+ */
+ __le32 max_frag_entries;
+} __packed;
+
+
+#define NUM_UNITS_IS_NUM_VDEVS 0x1
+#define NUM_UNITS_IS_NUM_PEERS 0x2
+
/* strucutre describing host memory chunk. */
struct host_memory_chunk {
/* id of the request that is passed up in service ready */
struct host_memory_chunk host_mem_chunks[1];
} __packed;
+/* _10x stucture is from 10.X FW API */
+struct wmi_init_cmd_10x {
+ struct wmi_resource_config_10x resource_config;
+ __le32 num_host_mem_chunks;
+
+ /*
+ * variable number of host memory chunks.
+ * This should be the last element in the structure
+ */
+ struct host_memory_chunk host_mem_chunks[1];
+} __packed;
+
/* TLV for channel list */
struct wmi_chan_list {
__le32 tag; /* WMI_CHAN_LIST_TAG */
*/
} __packed;
+/* This is the definition from 10.X firmware branch */
+struct wmi_start_scan_cmd_10x {
+ /* Scan ID */
+ __le32 scan_id;
+
+ /* Scan requestor ID */
+ __le32 scan_req_id;
+
+ /* VDEV id(interface) that is requesting scan */
+ __le32 vdev_id;
+
+ /* Scan Priority, input to scan scheduler */
+ __le32 scan_priority;
+
+ /* Scan events subscription */
+ __le32 notify_scan_events;
+
+ /* dwell time in msec on active channels */
+ __le32 dwell_time_active;
+
+ /* dwell time in msec on passive channels */
+ __le32 dwell_time_passive;
+
+ /*
+ * min time in msec on the BSS channel,only valid if atleast one
+ * VDEV is active
+ */
+ __le32 min_rest_time;
+
+ /*
+ * max rest time in msec on the BSS channel,only valid if at least
+ * one VDEV is active
+ */
+ /*
+ * the scanner will rest on the bss channel at least min_rest_time
+ * after min_rest_time the scanner will start checking for tx/rx
+ * activity on all VDEVs. if there is no activity the scanner will
+ * switch to off channel. if there is activity the scanner will let
+ * the radio on the bss channel until max_rest_time expires.at
+ * max_rest_time scanner will switch to off channel irrespective of
+ * activity. activity is determined by the idle_time parameter.
+ */
+ __le32 max_rest_time;
+
+ /*
+ * time before sending next set of probe requests.
+ * The scanner keeps repeating probe requests transmission with
+ * period specified by repeat_probe_time.
+ * The number of probe requests specified depends on the ssid_list
+ * and bssid_list
+ */
+ __le32 repeat_probe_time;
+
+ /* time in msec between 2 consequetive probe requests with in a set. */
+ __le32 probe_spacing_time;
+
+ /*
+ * data inactivity time in msec on bss channel that will be used by
+ * scanner for measuring the inactivity.
+ */
+ __le32 idle_time;
+
+ /* maximum time in msec allowed for scan */
+ __le32 max_scan_time;
+
+ /*
+ * delay in msec before sending first probe request after switching
+ * to a channel
+ */
+ __le32 probe_delay;
+
+ /* Scan control flags */
+ __le32 scan_ctrl_flags;
+
+ /*
+ * TLV (tag length value ) paramerters follow the scan_cmd structure.
+ * TLV can contain channel list, bssid list, ssid list and
+ * ie. the TLV tags are defined above;
+ */
+} __packed;
+
+
struct wmi_ssid_arg {
int len;
const u8 *ssid;
#define VDEV_DEFAULT_STATS_UPDATE_PERIOD 500
#define PEER_DEFAULT_STATS_UPDATE_PERIOD 500
+struct wmi_pdev_param_map {
+ u32 tx_chain_mask;
+ u32 rx_chain_mask;
+ u32 txpower_limit2g;
+ u32 txpower_limit5g;
+ u32 txpower_scale;
+ u32 beacon_gen_mode;
+ u32 beacon_tx_mode;
+ u32 resmgr_offchan_mode;
+ u32 protection_mode;
+ u32 dynamic_bw;
+ u32 non_agg_sw_retry_th;
+ u32 agg_sw_retry_th;
+ u32 sta_kickout_th;
+ u32 ac_aggrsize_scaling;
+ u32 ltr_enable;
+ u32 ltr_ac_latency_be;
+ u32 ltr_ac_latency_bk;
+ u32 ltr_ac_latency_vi;
+ u32 ltr_ac_latency_vo;
+ u32 ltr_ac_latency_timeout;
+ u32 ltr_sleep_override;
+ u32 ltr_rx_override;
+ u32 ltr_tx_activity_timeout;
+ u32 l1ss_enable;
+ u32 dsleep_enable;
+ u32 pcielp_txbuf_flush;
+ u32 pcielp_txbuf_watermark;
+ u32 pcielp_txbuf_tmo_en;
+ u32 pcielp_txbuf_tmo_value;
+ u32 pdev_stats_update_period;
+ u32 vdev_stats_update_period;
+ u32 peer_stats_update_period;
+ u32 bcnflt_stats_update_period;
+ u32 pmf_qos;
+ u32 arp_ac_override;
+ u32 arpdhcp_ac_override;
+ u32 dcs;
+ u32 ani_enable;
+ u32 ani_poll_period;
+ u32 ani_listen_period;
+ u32 ani_ofdm_level;
+ u32 ani_cck_level;
+ u32 dyntxchain;
+ u32 proxy_sta;
+ u32 idle_ps_config;
+ u32 power_gating_sleep;
+ u32 fast_channel_reset;
+ u32 burst_dur;
+ u32 burst_enable;
+};
+
+#define WMI_PDEV_PARAM_UNSUPPORTED 0
+
enum wmi_pdev_param {
/* TX chian mask */
WMI_PDEV_PARAM_TX_CHAIN_MASK = 0x1,
WMI_PDEV_PARAM_POWER_GATING_SLEEP,
};
+enum wmi_10x_pdev_param {
+ /* TX chian mask */
+ WMI_10X_PDEV_PARAM_TX_CHAIN_MASK = 0x1,
+ /* RX chian mask */
+ WMI_10X_PDEV_PARAM_RX_CHAIN_MASK,
+ /* TX power limit for 2G Radio */
+ WMI_10X_PDEV_PARAM_TXPOWER_LIMIT2G,
+ /* TX power limit for 5G Radio */
+ WMI_10X_PDEV_PARAM_TXPOWER_LIMIT5G,
+ /* TX power scale */
+ WMI_10X_PDEV_PARAM_TXPOWER_SCALE,
+ /* Beacon generation mode . 0: host, 1: target */
+ WMI_10X_PDEV_PARAM_BEACON_GEN_MODE,
+ /* Beacon generation mode . 0: staggered 1: bursted */
+ WMI_10X_PDEV_PARAM_BEACON_TX_MODE,
+ /*
+ * Resource manager off chan mode .
+ * 0: turn off off chan mode. 1: turn on offchan mode
+ */
+ WMI_10X_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
+ /*
+ * Protection mode:
+ * 0: no protection 1:use CTS-to-self 2: use RTS/CTS
+ */
+ WMI_10X_PDEV_PARAM_PROTECTION_MODE,
+ /* Dynamic bandwidth 0: disable 1: enable */
+ WMI_10X_PDEV_PARAM_DYNAMIC_BW,
+ /* Non aggregrate/ 11g sw retry threshold.0-disable */
+ WMI_10X_PDEV_PARAM_NON_AGG_SW_RETRY_TH,
+ /* aggregrate sw retry threshold. 0-disable*/
+ WMI_10X_PDEV_PARAM_AGG_SW_RETRY_TH,
+ /* Station kickout threshold (non of consecutive failures).0-disable */
+ WMI_10X_PDEV_PARAM_STA_KICKOUT_TH,
+ /* Aggerate size scaling configuration per AC */
+ WMI_10X_PDEV_PARAM_AC_AGGRSIZE_SCALING,
+ /* LTR enable */
+ WMI_10X_PDEV_PARAM_LTR_ENABLE,
+ /* LTR latency for BE, in us */
+ WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BE,
+ /* LTR latency for BK, in us */
+ WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BK,
+ /* LTR latency for VI, in us */
+ WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VI,
+ /* LTR latency for VO, in us */
+ WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VO,
+ /* LTR AC latency timeout, in ms */
+ WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT,
+ /* LTR platform latency override, in us */
+ WMI_10X_PDEV_PARAM_LTR_SLEEP_OVERRIDE,
+ /* LTR-RX override, in us */
+ WMI_10X_PDEV_PARAM_LTR_RX_OVERRIDE,
+ /* Tx activity timeout for LTR, in us */
+ WMI_10X_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT,
+ /* L1SS state machine enable */
+ WMI_10X_PDEV_PARAM_L1SS_ENABLE,
+ /* Deep sleep state machine enable */
+ WMI_10X_PDEV_PARAM_DSLEEP_ENABLE,
+ /* pdev level stats update period in ms */
+ WMI_10X_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD,
+ /* vdev level stats update period in ms */
+ WMI_10X_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD,
+ /* peer level stats update period in ms */
+ WMI_10X_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD,
+ /* beacon filter status update period */
+ WMI_10X_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD,
+ /* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */
+ WMI_10X_PDEV_PARAM_PMF_QOS,
+ /* Access category on which ARP and DHCP frames are sent */
+ WMI_10X_PDEV_PARAM_ARPDHCP_AC_OVERRIDE,
+ /* DCS configuration */
+ WMI_10X_PDEV_PARAM_DCS,
+ /* Enable/Disable ANI on target */
+ WMI_10X_PDEV_PARAM_ANI_ENABLE,
+ /* configure the ANI polling period */
+ WMI_10X_PDEV_PARAM_ANI_POLL_PERIOD,
+ /* configure the ANI listening period */
+ WMI_10X_PDEV_PARAM_ANI_LISTEN_PERIOD,
+ /* configure OFDM immunity level */
+ WMI_10X_PDEV_PARAM_ANI_OFDM_LEVEL,
+ /* configure CCK immunity level */
+ WMI_10X_PDEV_PARAM_ANI_CCK_LEVEL,
+ /* Enable/Disable CDD for 1x1 STAs in rate control module */
+ WMI_10X_PDEV_PARAM_DYNTXCHAIN,
+ /* Enable/Disable Fast channel reset*/
+ WMI_10X_PDEV_PARAM_FAST_CHANNEL_RESET,
+ /* Set Bursting DUR */
+ WMI_10X_PDEV_PARAM_BURST_DUR,
+ /* Set Bursting Enable*/
+ WMI_10X_PDEV_PARAM_BURST_ENABLE,
+};
+
struct wmi_pdev_set_param_cmd {
__le32 param_id;
__le32 param_value;
/* Value to disable fixed rate setting */
#define WMI_FIXED_RATE_NONE (0xff)
+struct wmi_vdev_param_map {
+ u32 rts_threshold;
+ u32 fragmentation_threshold;
+ u32 beacon_interval;
+ u32 listen_interval;
+ u32 multicast_rate;
+ u32 mgmt_tx_rate;
+ u32 slot_time;
+ u32 preamble;
+ u32 swba_time;
+ u32 wmi_vdev_stats_update_period;
+ u32 wmi_vdev_pwrsave_ageout_time;
+ u32 wmi_vdev_host_swba_interval;
+ u32 dtim_period;
+ u32 wmi_vdev_oc_scheduler_air_time_limit;
+ u32 wds;
+ u32 atim_window;
+ u32 bmiss_count_max;
+ u32 bmiss_first_bcnt;
+ u32 bmiss_final_bcnt;
+ u32 feature_wmm;
+ u32 chwidth;
+ u32 chextoffset;
+ u32 disable_htprotection;
+ u32 sta_quickkickout;
+ u32 mgmt_rate;
+ u32 protection_mode;
+ u32 fixed_rate;
+ u32 sgi;
+ u32 ldpc;
+ u32 tx_stbc;
+ u32 rx_stbc;
+ u32 intra_bss_fwd;
+ u32 def_keyid;
+ u32 nss;
+ u32 bcast_data_rate;
+ u32 mcast_data_rate;
+ u32 mcast_indicate;
+ u32 dhcp_indicate;
+ u32 unknown_dest_indicate;
+ u32 ap_keepalive_min_idle_inactive_time_secs;
+ u32 ap_keepalive_max_idle_inactive_time_secs;
+ u32 ap_keepalive_max_unresponsive_time_secs;
+ u32 ap_enable_nawds;
+ u32 mcast2ucast_set;
+ u32 enable_rtscts;
+ u32 txbf;
+ u32 packet_powersave;
+ u32 drop_unencry;
+ u32 tx_encap_type;
+ u32 ap_detect_out_of_sync_sleeping_sta_time_secs;
+};
+
+#define WMI_VDEV_PARAM_UNSUPPORTED 0
+
/* the definition of different VDEV parameters */
enum wmi_vdev_param {
/* RTS Threshold */
WMI_VDEV_PARAM_TX_ENCAP_TYPE,
};
+/* the definition of different VDEV parameters */
+enum wmi_10x_vdev_param {
+ /* RTS Threshold */
+ WMI_10X_VDEV_PARAM_RTS_THRESHOLD = 0x1,
+ /* Fragmentation threshold */
+ WMI_10X_VDEV_PARAM_FRAGMENTATION_THRESHOLD,
+ /* beacon interval in TUs */
+ WMI_10X_VDEV_PARAM_BEACON_INTERVAL,
+ /* Listen interval in TUs */
+ WMI_10X_VDEV_PARAM_LISTEN_INTERVAL,
+ /* muticast rate in Mbps */
+ WMI_10X_VDEV_PARAM_MULTICAST_RATE,
+ /* management frame rate in Mbps */
+ WMI_10X_VDEV_PARAM_MGMT_TX_RATE,
+ /* slot time (long vs short) */
+ WMI_10X_VDEV_PARAM_SLOT_TIME,
+ /* preamble (long vs short) */
+ WMI_10X_VDEV_PARAM_PREAMBLE,
+ /* SWBA time (time before tbtt in msec) */
+ WMI_10X_VDEV_PARAM_SWBA_TIME,
+ /* time period for updating VDEV stats */
+ WMI_10X_VDEV_STATS_UPDATE_PERIOD,
+ /* age out time in msec for frames queued for station in power save */
+ WMI_10X_VDEV_PWRSAVE_AGEOUT_TIME,
+ /*
+ * Host SWBA interval (time in msec before tbtt for SWBA event
+ * generation).
+ */
+ WMI_10X_VDEV_HOST_SWBA_INTERVAL,
+ /* DTIM period (specified in units of num beacon intervals) */
+ WMI_10X_VDEV_PARAM_DTIM_PERIOD,
+ /*
+ * scheduler air time limit for this VDEV. used by off chan
+ * scheduler.
+ */
+ WMI_10X_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT,
+ /* enable/dsiable WDS for this VDEV */
+ WMI_10X_VDEV_PARAM_WDS,
+ /* ATIM Window */
+ WMI_10X_VDEV_PARAM_ATIM_WINDOW,
+ /* BMISS max */
+ WMI_10X_VDEV_PARAM_BMISS_COUNT_MAX,
+ /* WMM enables/disabled */
+ WMI_10X_VDEV_PARAM_FEATURE_WMM,
+ /* Channel width */
+ WMI_10X_VDEV_PARAM_CHWIDTH,
+ /* Channel Offset */
+ WMI_10X_VDEV_PARAM_CHEXTOFFSET,
+ /* Disable HT Protection */
+ WMI_10X_VDEV_PARAM_DISABLE_HTPROTECTION,
+ /* Quick STA Kickout */
+ WMI_10X_VDEV_PARAM_STA_QUICKKICKOUT,
+ /* Rate to be used with Management frames */
+ WMI_10X_VDEV_PARAM_MGMT_RATE,
+ /* Protection Mode */
+ WMI_10X_VDEV_PARAM_PROTECTION_MODE,
+ /* Fixed rate setting */
+ WMI_10X_VDEV_PARAM_FIXED_RATE,
+ /* Short GI Enable/Disable */
+ WMI_10X_VDEV_PARAM_SGI,
+ /* Enable LDPC */
+ WMI_10X_VDEV_PARAM_LDPC,
+ /* Enable Tx STBC */
+ WMI_10X_VDEV_PARAM_TX_STBC,
+ /* Enable Rx STBC */
+ WMI_10X_VDEV_PARAM_RX_STBC,
+ /* Intra BSS forwarding */
+ WMI_10X_VDEV_PARAM_INTRA_BSS_FWD,
+ /* Setting Default xmit key for Vdev */
+ WMI_10X_VDEV_PARAM_DEF_KEYID,
+ /* NSS width */
+ WMI_10X_VDEV_PARAM_NSS,
+ /* Set the custom rate for the broadcast data frames */
+ WMI_10X_VDEV_PARAM_BCAST_DATA_RATE,
+ /* Set the custom rate (rate-code) for multicast data frames */
+ WMI_10X_VDEV_PARAM_MCAST_DATA_RATE,
+ /* Tx multicast packet indicate Enable/Disable */
+ WMI_10X_VDEV_PARAM_MCAST_INDICATE,
+ /* Tx DHCP packet indicate Enable/Disable */
+ WMI_10X_VDEV_PARAM_DHCP_INDICATE,
+ /* Enable host inspection of Tx unicast packet to unknown destination */
+ WMI_10X_VDEV_PARAM_UNKNOWN_DEST_INDICATE,
+
+ /* The minimum amount of time AP begins to consider STA inactive */
+ WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS,
+
+ /*
+ * An associated STA is considered inactive when there is no recent
+ * TX/RX activity and no downlink frames are buffered for it. Once a
+ * STA exceeds the maximum idle inactive time, the AP will send an
+ * 802.11 data-null as a keep alive to verify the STA is still
+ * associated. If the STA does ACK the data-null, or if the data-null
+ * is buffered and the STA does not retrieve it, the STA will be
+ * considered unresponsive
+ * (see WMI_10X_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS).
+ */
+ WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS,
+
+ /*
+ * An associated STA is considered unresponsive if there is no recent
+ * TX/RX activity and downlink frames are buffered for it. Once a STA
+ * exceeds the maximum unresponsive time, the AP will send a
+ * WMI_10X_STA_KICKOUT event to the host so the STA can be deleted. */
+ WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS,
+
+ /* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */
+ WMI_10X_VDEV_PARAM_AP_ENABLE_NAWDS,
+
+ WMI_10X_VDEV_PARAM_MCAST2UCAST_SET,
+ /* Enable/Disable RTS-CTS */
+ WMI_10X_VDEV_PARAM_ENABLE_RTSCTS,
+
+ WMI_10X_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS,
+};
+
/* slot time long */
#define WMI_VDEV_SLOT_TIME_LONG 0x1
/* slot time short */
#define WMI_MAX_EVENT 0x1000
/* Maximum number of pending TXed WMI packets */
-#define WMI_MAX_PENDING_TX_COUNT 128
#define WMI_SKB_HEADROOM sizeof(struct wmi_cmd_hdr)
/* By default disable power save for IBSS */
void ath10k_wmi_detach(struct ath10k *ar);
int ath10k_wmi_wait_for_service_ready(struct ath10k *ar);
int ath10k_wmi_wait_for_unified_ready(struct ath10k *ar);
-void ath10k_wmi_flush_tx(struct ath10k *ar);
int ath10k_wmi_connect_htc_service(struct ath10k *ar);
int ath10k_wmi_pdev_set_channel(struct ath10k *ar,
int ath10k_wmi_pdev_resume_target(struct ath10k *ar);
int ath10k_wmi_pdev_set_regdomain(struct ath10k *ar, u16 rd, u16 rd2g,
u16 rd5g, u16 ctl2g, u16 ctl5g);
-int ath10k_wmi_pdev_set_param(struct ath10k *ar, enum wmi_pdev_param id,
- u32 value);
+int ath10k_wmi_pdev_set_param(struct ath10k *ar, u32 id, u32 value);
int ath10k_wmi_cmd_init(struct ath10k *ar);
int ath10k_wmi_start_scan(struct ath10k *ar, const struct wmi_start_scan_arg *);
void ath10k_wmi_start_scan_init(struct ath10k *ar, struct wmi_start_scan_arg *);
const u8 *bssid);
int ath10k_wmi_vdev_down(struct ath10k *ar, u32 vdev_id);
int ath10k_wmi_vdev_set_param(struct ath10k *ar, u32 vdev_id,
- enum wmi_vdev_param param_id, u32 param_value);
+ u32 param_id, u32 param_value);
int ath10k_wmi_vdev_install_key(struct ath10k *ar,
const struct wmi_vdev_install_key_arg *arg);
int ath10k_wmi_peer_create(struct ath10k *ar, u32 vdev_id,
enum wmi_ap_ps_peer_param param_id, u32 value);
int ath10k_wmi_scan_chan_list(struct ath10k *ar,
const struct wmi_scan_chan_list_arg *arg);
-int ath10k_wmi_beacon_send(struct ath10k *ar, const struct wmi_bcn_tx_arg *arg);
+int ath10k_wmi_beacon_send_nowait(struct ath10k *ar,
+ const struct wmi_bcn_tx_arg *arg);
int ath10k_wmi_pdev_set_wmm_params(struct ath10k *ar,
const struct wmi_pdev_set_wmm_params_arg *arg);
int ath10k_wmi_request_stats(struct ath10k *ar, enum wmi_stats_id stats_id);
int ath10k_wmi_force_fw_hang(struct ath10k *ar,
enum wmi_force_fw_hang_type type, u32 delay_ms);
+int ath10k_wmi_mgmt_tx(struct ath10k *ar, struct sk_buff *skb);
#endif /* _WMI_H_ */
projects / cascardo / linux.git / blobdiff