#define WMI_CMD_GRP(grp_id) (((grp_id) << 12) | 0x1)
#define WMI_EVT_GRP_START_ID(grp_id) (((grp_id) << 12) | 0x1)
-/* Command IDs and commande events. */
+#define WMI_CMD_UNDEFINED 0
+
+/* Command IDs and command events for MAIN FW. */
enum wmi_cmd_id {
WMI_INIT_CMDID = 0x1,
WMI_GPIO_INPUT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_GPIO),
};
+/* Command IDs and command events for 10.X firmware */
+enum wmi_10x_cmd_id {
+ WMI_10X_START_CMDID = 0x9000,
+ WMI_10X_END_CMDID = 0x9FFF,
+
+ /* initialize the wlan sub system */
+ WMI_10X_INIT_CMDID,
+
+ /* Scan specific commands */
+
+ WMI_10X_START_SCAN_CMDID = WMI_10X_START_CMDID,
+ WMI_10X_STOP_SCAN_CMDID,
+ WMI_10X_SCAN_CHAN_LIST_CMDID,
+ WMI_10X_ECHO_CMDID,
+
+ /* PDEV(physical device) specific commands */
+ WMI_10X_PDEV_SET_REGDOMAIN_CMDID,
+ WMI_10X_PDEV_SET_CHANNEL_CMDID,
+ WMI_10X_PDEV_SET_PARAM_CMDID,
+ WMI_10X_PDEV_PKTLOG_ENABLE_CMDID,
+ WMI_10X_PDEV_PKTLOG_DISABLE_CMDID,
+ WMI_10X_PDEV_SET_WMM_PARAMS_CMDID,
+ WMI_10X_PDEV_SET_HT_CAP_IE_CMDID,
+ WMI_10X_PDEV_SET_VHT_CAP_IE_CMDID,
+ WMI_10X_PDEV_SET_BASE_MACADDR_CMDID,
+ WMI_10X_PDEV_SET_DSCP_TID_MAP_CMDID,
+ WMI_10X_PDEV_SET_QUIET_MODE_CMDID,
+ WMI_10X_PDEV_GREEN_AP_PS_ENABLE_CMDID,
+ WMI_10X_PDEV_GET_TPC_CONFIG_CMDID,
+
+ /* VDEV(virtual device) specific commands */
+ WMI_10X_VDEV_CREATE_CMDID,
+ WMI_10X_VDEV_DELETE_CMDID,
+ WMI_10X_VDEV_START_REQUEST_CMDID,
+ WMI_10X_VDEV_RESTART_REQUEST_CMDID,
+ WMI_10X_VDEV_UP_CMDID,
+ WMI_10X_VDEV_STOP_CMDID,
+ WMI_10X_VDEV_DOWN_CMDID,
+ WMI_10X_VDEV_STANDBY_RESPONSE_CMDID,
+ WMI_10X_VDEV_RESUME_RESPONSE_CMDID,
+ WMI_10X_VDEV_SET_PARAM_CMDID,
+ WMI_10X_VDEV_INSTALL_KEY_CMDID,
+
+ /* peer specific commands */
+ WMI_10X_PEER_CREATE_CMDID,
+ WMI_10X_PEER_DELETE_CMDID,
+ WMI_10X_PEER_FLUSH_TIDS_CMDID,
+ WMI_10X_PEER_SET_PARAM_CMDID,
+ WMI_10X_PEER_ASSOC_CMDID,
+ WMI_10X_PEER_ADD_WDS_ENTRY_CMDID,
+ WMI_10X_PEER_REMOVE_WDS_ENTRY_CMDID,
+ WMI_10X_PEER_MCAST_GROUP_CMDID,
+
+ /* beacon/management specific commands */
+
+ WMI_10X_BCN_TX_CMDID,
+ WMI_10X_BCN_PRB_TMPL_CMDID,
+ WMI_10X_BCN_FILTER_RX_CMDID,
+ WMI_10X_PRB_REQ_FILTER_RX_CMDID,
+ WMI_10X_MGMT_TX_CMDID,
+
+ /* commands to directly control ba negotiation directly from host. */
+ WMI_10X_ADDBA_CLEAR_RESP_CMDID,
+ WMI_10X_ADDBA_SEND_CMDID,
+ WMI_10X_ADDBA_STATUS_CMDID,
+ WMI_10X_DELBA_SEND_CMDID,
+ WMI_10X_ADDBA_SET_RESP_CMDID,
+ WMI_10X_SEND_SINGLEAMSDU_CMDID,
+
+ /* Station power save specific config */
+ WMI_10X_STA_POWERSAVE_MODE_CMDID,
+ WMI_10X_STA_POWERSAVE_PARAM_CMDID,
+ WMI_10X_STA_MIMO_PS_MODE_CMDID,
+
+ /* set debug log config */
+ WMI_10X_DBGLOG_CFG_CMDID,
+
+ /* DFS-specific commands */
+ WMI_10X_PDEV_DFS_ENABLE_CMDID,
+ WMI_10X_PDEV_DFS_DISABLE_CMDID,
+
+ /* QVIT specific command id */
+ WMI_10X_PDEV_QVIT_CMDID,
+
+ /* Offload Scan and Roaming related commands */
+ WMI_10X_ROAM_SCAN_MODE,
+ WMI_10X_ROAM_SCAN_RSSI_THRESHOLD,
+ WMI_10X_ROAM_SCAN_PERIOD,
+ WMI_10X_ROAM_SCAN_RSSI_CHANGE_THRESHOLD,
+ WMI_10X_ROAM_AP_PROFILE,
+ WMI_10X_OFL_SCAN_ADD_AP_PROFILE,
+ WMI_10X_OFL_SCAN_REMOVE_AP_PROFILE,
+ WMI_10X_OFL_SCAN_PERIOD,
+
+ /* P2P specific commands */
+ WMI_10X_P2P_DEV_SET_DEVICE_INFO,
+ WMI_10X_P2P_DEV_SET_DISCOVERABILITY,
+ WMI_10X_P2P_GO_SET_BEACON_IE,
+ WMI_10X_P2P_GO_SET_PROBE_RESP_IE,
+
+ /* AP power save specific config */
+ WMI_10X_AP_PS_PEER_PARAM_CMDID,
+ WMI_10X_AP_PS_PEER_UAPSD_COEX_CMDID,
+
+ /* Rate-control specific commands */
+ WMI_10X_PEER_RATE_RETRY_SCHED_CMDID,
+
+ /* WLAN Profiling commands. */
+ WMI_10X_WLAN_PROFILE_TRIGGER_CMDID,
+ WMI_10X_WLAN_PROFILE_SET_HIST_INTVL_CMDID,
+ WMI_10X_WLAN_PROFILE_GET_PROFILE_DATA_CMDID,
+ WMI_10X_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID,
+ WMI_10X_WLAN_PROFILE_LIST_PROFILE_ID_CMDID,
+
+ /* Suspend resume command Ids */
+ WMI_10X_PDEV_SUSPEND_CMDID,
+ WMI_10X_PDEV_RESUME_CMDID,
+
+ /* Beacon filter commands */
+ WMI_10X_ADD_BCN_FILTER_CMDID,
+ WMI_10X_RMV_BCN_FILTER_CMDID,
+
+ /* WOW Specific WMI commands*/
+ WMI_10X_WOW_ADD_WAKE_PATTERN_CMDID,
+ WMI_10X_WOW_DEL_WAKE_PATTERN_CMDID,
+ WMI_10X_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID,
+ WMI_10X_WOW_ENABLE_CMDID,
+ WMI_10X_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID,
+
+ /* RTT measurement related cmd */
+ WMI_10X_RTT_MEASREQ_CMDID,
+ WMI_10X_RTT_TSF_CMDID,
+
+ /* transmit beacon by value */
+ WMI_10X_PDEV_SEND_BCN_CMDID,
+
+ /* F/W stats */
+ WMI_10X_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID,
+ WMI_10X_VDEV_SPECTRAL_SCAN_ENABLE_CMDID,
+ WMI_10X_REQUEST_STATS_CMDID,
+
+ /* GPIO Configuration */
+ WMI_10X_GPIO_CONFIG_CMDID,
+ WMI_10X_GPIO_OUTPUT_CMDID,
+
+ WMI_10X_PDEV_UTF_CMDID = WMI_10X_END_CMDID - 1,
+};
+
+enum wmi_10x_event_id {
+ WMI_10X_SERVICE_READY_EVENTID = 0x8000,
+ WMI_10X_READY_EVENTID,
+ WMI_10X_START_EVENTID = 0x9000,
+ WMI_10X_END_EVENTID = 0x9FFF,
+
+ /* Scan specific events */
+ WMI_10X_SCAN_EVENTID = WMI_10X_START_EVENTID,
+ WMI_10X_ECHO_EVENTID,
+ WMI_10X_DEBUG_MESG_EVENTID,
+ WMI_10X_UPDATE_STATS_EVENTID,
+
+ /* Instantaneous RSSI event */
+ WMI_10X_INST_RSSI_STATS_EVENTID,
+
+ /* VDEV specific events */
+ WMI_10X_VDEV_START_RESP_EVENTID,
+ WMI_10X_VDEV_STANDBY_REQ_EVENTID,
+ WMI_10X_VDEV_RESUME_REQ_EVENTID,
+ WMI_10X_VDEV_STOPPED_EVENTID,
+
+ /* peer specific events */
+ WMI_10X_PEER_STA_KICKOUT_EVENTID,
+
+ /* beacon/mgmt specific events */
+ WMI_10X_HOST_SWBA_EVENTID,
+ WMI_10X_TBTTOFFSET_UPDATE_EVENTID,
+ WMI_10X_MGMT_RX_EVENTID,
+
+ /* Channel stats event */
+ WMI_10X_CHAN_INFO_EVENTID,
+
+ /* PHY Error specific WMI event */
+ WMI_10X_PHYERR_EVENTID,
+
+ /* Roam event to trigger roaming on host */
+ WMI_10X_ROAM_EVENTID,
+
+ /* matching AP found from list of profiles */
+ WMI_10X_PROFILE_MATCH,
+
+ /* debug print message used for tracing FW code while debugging */
+ WMI_10X_DEBUG_PRINT_EVENTID,
+ /* VI spoecific event */
+ WMI_10X_PDEV_QVIT_EVENTID,
+ /* FW code profile data in response to profile request */
+ WMI_10X_WLAN_PROFILE_DATA_EVENTID,
+
+ /*RTT related event ID*/
+ WMI_10X_RTT_MEASUREMENT_REPORT_EVENTID,
+ WMI_10X_TSF_MEASUREMENT_REPORT_EVENTID,
+ WMI_10X_RTT_ERROR_REPORT_EVENTID,
+
+ WMI_10X_WOW_WAKEUP_HOST_EVENTID,
+ WMI_10X_DCS_INTERFERENCE_EVENTID,
+
+ /* TPC config for the current operating channel */
+ WMI_10X_PDEV_TPC_CONFIG_EVENTID,
+
+ WMI_10X_GPIO_INPUT_EVENTID,
+ WMI_10X_PDEV_UTF_EVENTID = WMI_10X_END_EVENTID-1,
+};
+
enum wmi_phy_mode {
MODE_11A = 0, /* 11a Mode */
MODE_11G = 1, /* 11b/g Mode */
projects / cascardo / linux.git / blobdiff