int next_rate = il3945_get_prev_ieee_rate(rate);
switch (il->band) {
- case IEEE80211_BAND_5GHZ:
+ case NL80211_BAND_5GHZ:
if (rate == RATE_12M_IDX)
next_rate = RATE_9M_IDX;
else if (rate == RATE_6M_IDX)
next_rate = RATE_6M_IDX;
break;
- case IEEE80211_BAND_2GHZ:
+ case NL80211_BAND_2GHZ:
if (!(il->_3945.sta_supp_rates & IL_OFDM_RATES_MASK) &&
il_is_associated(il)) {
if (rate == RATE_11M_IDX)
/* Fill the MRR chain with some info about on-chip retransmissions */
rate_idx = il3945_hwrate_to_plcp_idx(tx_resp->rate);
- if (info->band == IEEE80211_BAND_5GHZ)
+ if (info->band == NL80211_BAND_5GHZ)
rate_idx -= IL_FIRST_OFDM_RATE;
fail = tx_resp->failure_frame;
rx_status.mactime = le64_to_cpu(rx_end->timestamp);
rx_status.band =
(rx_hdr->
- phy_flags & RX_RES_PHY_FLAGS_BAND_24_MSK) ? IEEE80211_BAND_2GHZ :
- IEEE80211_BAND_5GHZ;
+ phy_flags & RX_RES_PHY_FLAGS_BAND_24_MSK) ? NL80211_BAND_2GHZ :
+ NL80211_BAND_5GHZ;
rx_status.freq =
ieee80211_channel_to_frequency(le16_to_cpu(rx_hdr->channel),
rx_status.band);
rx_status.rate_idx = il3945_hwrate_to_plcp_idx(rx_hdr->rate);
- if (rx_status.band == IEEE80211_BAND_5GHZ)
+ if (rx_status.band == NL80211_BAND_5GHZ)
rx_status.rate_idx -= IL_FIRST_OFDM_RATE;
rx_status.antenna =
chan = le16_to_cpu(il->active.channel);
- txpower.band = (il->band == IEEE80211_BAND_5GHZ) ? 0 : 1;
+ txpower.band = (il->band == NL80211_BAND_5GHZ) ? 0 : 1;
ch_info = il_get_channel_info(il, il->band, chan);
if (!ch_info) {
IL_ERR("Failed to get channel info for channel %d [%d]\n", chan,
il3945_sync_sta(il, vif_priv->ibss_bssid_sta_id,
(il->band ==
- IEEE80211_BAND_5GHZ) ? RATE_6M_PLCP :
+ NL80211_BAND_5GHZ) ? RATE_6M_PLCP :
RATE_1M_PLCP);
il3945_rate_scale_init(il->hw, vif_priv->ibss_bssid_sta_id);
}
switch (il->band) {
- case IEEE80211_BAND_5GHZ:
+ case NL80211_BAND_5GHZ:
D_RATE("Select A mode rate scale\n");
/* If one of the following CCK rates is used,
* have it fall back to the 6M OFDM rate */
il3945_rates[IL_FIRST_OFDM_RATE].table_rs_idx;
break;
- case IEEE80211_BAND_2GHZ:
+ case NL80211_BAND_2GHZ:
D_RATE("Select B/G mode rate scale\n");
/* If an OFDM rate is used, have it fall back to the
* 1M CCK rates */