};
-----------------------------------------------------------------------
-Hisilicon HiP05 PCIe-SAS system controller
+Hisilicon HiP05/HiP06 PCIe-SAS sub system controller
Required properties:
- compatible : "hisilicon,pcie-sas-subctrl", "syscon";
- reg : Register address and size
-The HiP05 PCIe-SAS system controller is shared by PCIe and SAS controllers in
-HiP05 Soc to implement some basic configurations.
+The PCIe-SAS sub system controller is shared by PCIe and SAS controllers in
+HiP05 or HiP06 Soc to implement some basic configurations.
Example:
- /* for HiP05 PCIe-SAS system */
- pcie_sas: system_controller@0xb0000000 {
+ /* for HiP05 PCIe-SAS sub system */
+ pcie_sas: system_controller@b0000000 {
compatible = "hisilicon,pcie-sas-subctrl", "syscon";
reg = <0xb0000000 0x10000>;
};
-Hisilicon HiP05 PERISUB system controller
+Hisilicon HiP05/HiP06 PERI sub system controller
Required properties:
-- compatible : "hisilicon,hip05-perisubc", "syscon";
+- compatible : "hisilicon,peri-subctrl", "syscon";
- reg : Register address and size
-The HiP05 PERISUB system controller is shared by peripheral controllers in
-HiP05 Soc to implement some basic configurations. The peripheral
+The PERI sub system controller is shared by peripheral controllers in
+HiP05 or HiP06 Soc to implement some basic configurations. The peripheral
controllers include mdio, ddr, iic, uart, timer and so on.
Example:
- /* for HiP05 perisub-ctrl-c system */
+ /* for HiP05 sub peri system */
peri_c_subctrl: syscon@80000000 {
- compatible = "hisilicon,hip05-perisubc", "syscon";
+ compatible = "hisilicon,peri-subctrl", "syscon";
reg = <0x0 0x80000000 0x0 0x10000>;
};
+
+Hisilicon HiP05/HiP06 DSA sub system controller
+
+Required properties:
+- compatible : "hisilicon,dsa-subctrl", "syscon";
+- reg : Register address and size
+
+The DSA sub system controller is shared by peripheral controllers in
+HiP05 or HiP06 Soc to implement some basic configurations.
+
+Example:
+ /* for HiP05 dsa sub system */
+ pcie_sas: system_controller@a0000000 {
+ compatible = "hisilicon,dsa-subctrl", "syscon";
+ reg = <0xa0000000 0x10000>;
+ };
+
-----------------------------------------------------------------------
Hisilicon CPU controller
- Rockchip RK3399 evb:
Required root node properties:
- compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
+
+- Tronsmart Orion R68 Meta
+ Required root node properties:
+ - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
Bus matrix required properties:
- compatible = "zte,zx-bus-matrix"
+
+
+---------------------------------------
+- ZX296718 SoC:
+ Required root node properties:
+ - compatible = "zte,zx296718"
+
+ZX296718 EVB board:
+ - "zte,zx296718-evb"
+
+System management required properties:
+ - compatible = "zte,zx296718-aon-sysctrl"
+ - compatible = "zte,zx296718-sysctrl"
+
+Example:
+aon_sysctrl: aon-sysctrl@116000 {
+ compatible = "zte,zx296718-aon-sysctrl", "syscon";
+ reg = <0x116000 0x1000>;
+};
+
+sysctrl: sysctrl@1463000 {
+ compatible = "zte,zx296718-sysctrl", "syscon";
+ reg = <0x1463000 0x1000>;
+};
select GENERIC_CLOCKEVENTS
select GPIOLIB
select PINCTRL
+ select PM
+ select PM_GENERIC_DOMAINS
select RESET_CONTROLLER
help
This enables support for the NVIDIA Tegra SoC family.
dts-dirs += sprd
dts-dirs += xilinx
dts-dirs += lg
+dts-dirs += zte
subdir-y := $(dts-dirs)
enable-method = "spin-table";
cpu-release-addr = <0x1 0x0000fff8>;
next-level-cache = <&xgene_L2_0>;
+ #clock-cells = <1>;
+ clocks = <&pmd0clk 0>;
};
cpu@001 {
device_type = "cpu";
enable-method = "spin-table";
cpu-release-addr = <0x1 0x0000fff8>;
next-level-cache = <&xgene_L2_0>;
+ #clock-cells = <1>;
+ clocks = <&pmd0clk 0>;
};
cpu@100 {
device_type = "cpu";
enable-method = "spin-table";
cpu-release-addr = <0x1 0x0000fff8>;
next-level-cache = <&xgene_L2_1>;
+ #clock-cells = <1>;
+ clocks = <&pmd1clk 0>;
};
cpu@101 {
device_type = "cpu";
enable-method = "spin-table";
cpu-release-addr = <0x1 0x0000fff8>;
next-level-cache = <&xgene_L2_1>;
+ #clock-cells = <1>;
+ clocks = <&pmd1clk 0>;
};
cpu@200 {
device_type = "cpu";
enable-method = "spin-table";
cpu-release-addr = <0x1 0x0000fff8>;
next-level-cache = <&xgene_L2_2>;
+ #clock-cells = <1>;
+ clocks = <&pmd2clk 0>;
};
cpu@201 {
device_type = "cpu";
enable-method = "spin-table";
cpu-release-addr = <0x1 0x0000fff8>;
next-level-cache = <&xgene_L2_2>;
+ #clock-cells = <1>;
+ clocks = <&pmd2clk 0>;
};
cpu@300 {
device_type = "cpu";
enable-method = "spin-table";
cpu-release-addr = <0x1 0x0000fff8>;
next-level-cache = <&xgene_L2_3>;
+ #clock-cells = <1>;
+ clocks = <&pmd3clk 0>;
};
cpu@301 {
device_type = "cpu";
enable-method = "spin-table";
cpu-release-addr = <0x1 0x0000fff8>;
next-level-cache = <&xgene_L2_3>;
+ #clock-cells = <1>;
+ clocks = <&pmd3clk 0>;
};
xgene_L2_0: l2-cache-0 {
compatible = "cache";
clock-output-names = "refclk";
};
+ pmdpll: pmdpll@170000f0 {
+ compatible = "apm,xgene-pcppll-v2-clock";
+ #clock-cells = <1>;
+ clocks = <&refclk 0>;
+ reg = <0x0 0x170000f0 0x0 0x10>;
+ clock-output-names = "pmdpll";
+ };
+
+ pmd0clk: pmd0clk@7e200200 {
+ compatible = "apm,xgene-pmd-clock";
+ #clock-cells = <1>;
+ clocks = <&pmdpll 0>;
+ reg = <0x0 0x7e200200 0x0 0x10>;
+ clock-output-names = "pmd0clk";
+ };
+
+ pmd1clk: pmd1clk@7e200210 {
+ compatible = "apm,xgene-pmd-clock";
+ #clock-cells = <1>;
+ clocks = <&pmdpll 0>;
+ reg = <0x0 0x7e200210 0x0 0x10>;
+ clock-output-names = "pmd1clk";
+ };
+
+ pmd2clk: pmd2clk@7e200220 {
+ compatible = "apm,xgene-pmd-clock";
+ #clock-cells = <1>;
+ clocks = <&pmdpll 0>;
+ reg = <0x0 0x7e200220 0x0 0x10>;
+ clock-output-names = "pmd2clk";
+ };
+
+ pmd3clk: pmd3clk@7e200230 {
+ compatible = "apm,xgene-pmd-clock";
+ #clock-cells = <1>;
+ clocks = <&pmdpll 0>;
+ reg = <0x0 0x7e200230 0x0 0x10>;
+ clock-output-names = "pmd3clk";
+ };
+
socpll: socpll@17000120 {
compatible = "apm,xgene-socpll-v2-clock";
#clock-cells = <1>;
};
};
+ pmu: pmu@78810000 {
+ compatible = "apm,xgene-pmu-v2";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ regmap-csw = <&csw>;
+ regmap-mcba = <&mcba>;
+ regmap-mcbb = <&mcbb>;
+ reg = <0x0 0x78810000 0x0 0x1000>;
+ interrupts = <0x0 0x22 0x4>;
+
+ pmul3c@7e610000 {
+ compatible = "apm,xgene-pmu-l3c";
+ reg = <0x0 0x7e610000 0x0 0x1000>;
+ };
+
+ pmuiob@7e940000 {
+ compatible = "apm,xgene-pmu-iob";
+ reg = <0x0 0x7e940000 0x0 0x1000>;
+ };
+
+ pmucmcb@7e710000 {
+ compatible = "apm,xgene-pmu-mcb";
+ reg = <0x0 0x7e710000 0x0 0x1000>;
+ enable-bit-index = <0>;
+ };
+
+ pmucmcb@7e730000 {
+ compatible = "apm,xgene-pmu-mcb";
+ reg = <0x0 0x7e730000 0x0 0x1000>;
+ enable-bit-index = <1>;
+ };
+
+ pmucmc@7e810000 {
+ compatible = "apm,xgene-pmu-mc";
+ reg = <0x0 0x7e810000 0x0 0x1000>;
+ enable-bit-index = <0>;
+ };
+
+ pmucmc@7e850000 {
+ compatible = "apm,xgene-pmu-mc";
+ reg = <0x0 0x7e850000 0x0 0x1000>;
+ enable-bit-index = <1>;
+ };
+
+ pmucmc@7e890000 {
+ compatible = "apm,xgene-pmu-mc";
+ reg = <0x0 0x7e890000 0x0 0x1000>;
+ enable-bit-index = <2>;
+ };
+
+ pmucmc@7e8d0000 {
+ compatible = "apm,xgene-pmu-mc";
+ reg = <0x0 0x7e8d0000 0x0 0x1000>;
+ enable-bit-index = <3>;
+ };
+ };
+
mailbox: mailbox@10540000 {
compatible = "apm,xgene-slimpro-mbox";
reg = <0x0 0x10540000 0x0 0x8000>;
mboxes = <&mailbox 0>;
};
+ hwmonslimpro {
+ compatible = "apm,xgene-slimpro-hwmon";
+ mboxes = <&mailbox 7>;
+ };
+
serial0: serial@10600000 {
device_type = "serial";
compatible = "ns16550";
dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
- interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x10 0x1
- 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x11 0x1
- 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x12 0x1
- 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x13 0x1>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x10 0x4
+ 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x11 0x4
+ 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x12 0x4
+ 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x13 0x4>;
dma-coherent;
clocks = <&pcie0clk 0>;
msi-parent = <&v2m0>;
dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
- interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x16 0x1
- 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x17 0x1
- 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x18 0x1
- 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x19 0x1>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 0x16 0x4
+ 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 0x17 0x4
+ 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 0x18 0x4
+ 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 0x19 0x4>;
dma-coherent;
clocks = <&pcie1clk 0>;
msi-parent = <&v2m0>;
};
};
+ pmu: pmu@78810000 {
+ compatible = "apm,xgene-pmu-v2";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ regmap-csw = <&csw>;
+ regmap-mcba = <&mcba>;
+ regmap-mcbb = <&mcbb>;
+ reg = <0x0 0x78810000 0x0 0x1000>;
+ interrupts = <0x0 0x22 0x4>;
+
+ pmul3c@7e610000 {
+ compatible = "apm,xgene-pmu-l3c";
+ reg = <0x0 0x7e610000 0x0 0x1000>;
+ };
+
+ pmuiob@7e940000 {
+ compatible = "apm,xgene-pmu-iob";
+ reg = <0x0 0x7e940000 0x0 0x1000>;
+ };
+
+ pmucmcb@7e710000 {
+ compatible = "apm,xgene-pmu-mcb";
+ reg = <0x0 0x7e710000 0x0 0x1000>;
+ enable-bit-index = <0>;
+ };
+
+ pmucmcb@7e730000 {
+ compatible = "apm,xgene-pmu-mcb";
+ reg = <0x0 0x7e730000 0x0 0x1000>;
+ enable-bit-index = <1>;
+ };
+
+ pmucmc@7e810000 {
+ compatible = "apm,xgene-pmu-mc";
+ reg = <0x0 0x7e810000 0x0 0x1000>;
+ enable-bit-index = <0>;
+ };
+
+ pmucmc@7e850000 {
+ compatible = "apm,xgene-pmu-mc";
+ reg = <0x0 0x7e850000 0x0 0x1000>;
+ enable-bit-index = <1>;
+ };
+
+ pmucmc@7e890000 {
+ compatible = "apm,xgene-pmu-mc";
+ reg = <0x0 0x7e890000 0x0 0x1000>;
+ enable-bit-index = <2>;
+ };
+
+ pmucmc@7e8d0000 {
+ compatible = "apm,xgene-pmu-mc";
+ reg = <0x0 0x7e8d0000 0x0 0x1000>;
+ enable-bit-index = <3>;
+ };
+ };
+
pcie0: pcie@1f2b0000 {
status = "disabled";
device_type = "pci";
dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
- interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1
- 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1
- 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1
- 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x4
+ 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x4
+ 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x4
+ 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x4>;
dma-coherent;
clocks = <&pcie0clk 0>;
msi-parent = <&msi>;
dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
- interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc8 0x1
- 0x0 0x0 0x0 0x2 &gic 0x0 0xc9 0x1
- 0x0 0x0 0x0 0x3 &gic 0x0 0xca 0x1
- 0x0 0x0 0x0 0x4 &gic 0x0 0xcb 0x1>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc8 0x4
+ 0x0 0x0 0x0 0x2 &gic 0x0 0xc9 0x4
+ 0x0 0x0 0x0 0x3 &gic 0x0 0xca 0x4
+ 0x0 0x0 0x0 0x4 &gic 0x0 0xcb 0x4>;
dma-coherent;
clocks = <&pcie1clk 0>;
msi-parent = <&msi>;
dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
- interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xce 0x1
- 0x0 0x0 0x0 0x2 &gic 0x0 0xcf 0x1
- 0x0 0x0 0x0 0x3 &gic 0x0 0xd0 0x1
- 0x0 0x0 0x0 0x4 &gic 0x0 0xd1 0x1>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xce 0x4
+ 0x0 0x0 0x0 0x2 &gic 0x0 0xcf 0x4
+ 0x0 0x0 0x0 0x3 &gic 0x0 0xd0 0x4
+ 0x0 0x0 0x0 0x4 &gic 0x0 0xd1 0x4>;
dma-coherent;
clocks = <&pcie2clk 0>;
msi-parent = <&msi>;
dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
- interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xd4 0x1
- 0x0 0x0 0x0 0x2 &gic 0x0 0xd5 0x1
- 0x0 0x0 0x0 0x3 &gic 0x0 0xd6 0x1
- 0x0 0x0 0x0 0x4 &gic 0x0 0xd7 0x1>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xd4 0x4
+ 0x0 0x0 0x0 0x2 &gic 0x0 0xd5 0x4
+ 0x0 0x0 0x0 0x3 &gic 0x0 0xd6 0x4
+ 0x0 0x0 0x0 0x4 &gic 0x0 0xd7 0x4>;
dma-coherent;
clocks = <&pcie3clk 0>;
msi-parent = <&msi>;
dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000
0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>;
interrupt-map-mask = <0x0 0x0 0x0 0x7>;
- interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xda 0x1
- 0x0 0x0 0x0 0x2 &gic 0x0 0xdb 0x1
- 0x0 0x0 0x0 0x3 &gic 0x0 0xdc 0x1
- 0x0 0x0 0x0 0x4 &gic 0x0 0xdd 0x1>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xda 0x4
+ 0x0 0x0 0x0 0x2 &gic 0x0 0xdb 0x4
+ 0x0 0x0 0x0 0x3 &gic 0x0 0xdc 0x4
+ 0x0 0x0 0x0 0x4 &gic 0x0 0xdd 0x4>;
dma-coherent;
clocks = <&pcie4clk 0>;
msi-parent = <&msi>;
mboxes = <&mailbox 0>;
};
+ hwmonslimpro {
+ compatible = "apm,xgene-slimpro-hwmon";
+ mboxes = <&mailbox 7>;
+ };
+
serial0: serial@1c020000 {
status = "disabled";
device_type = "serial";
};
};
+ pwm: pwm@66010000 {
+ compatible = "brcm,iproc-pwm";
+ reg = <0x66010000 0x28>;
+ clocks = <&osc>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
mdio_mux_iproc: mdio-mux@6602023c {
compatible = "brcm,mdio-mux-iproc";
reg = <0x6602023c 0x14>;
*/
#include <dt-bindings/clock/exynos7-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
compatible = "samsung,exynos7";
timer {
compatible = "arm,armv8-timer";
- interrupts = <1 13 0xff08>,
- <1 14 0xff08>,
- <1 11 0xff08>,
- <1 10 0xff08>;
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
};
pmu_system_controller: system-controller@105c0000 {
gpio1 = &gpio2;
gpio2 = &gpio3;
gpio3 = &gpio4;
- serial0 = &lpuart0;
- serial1 = &lpuart1;
- serial2 = &lpuart2;
- serial3 = &lpuart3;
- serial4 = &lpuart4;
- serial5 = &lpuart5;
+ serial0 = &duart0;
+ serial1 = &duart1;
+ serial2 = &duart2;
+ serial3 = &duart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
};
};
aliases {
crypto = &crypto;
+ serial0 = &duart0;
+ serial1 = &duart1;
+ serial2 = &duart2;
+ serial3 = &duart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
};
};
bus-width = <4>;
};
+ ddr: memory-controller@1080000 {
+ compatible = "fsl,qoriq-memory-controller";
+ reg = <0x0 0x1080000 0x0 0x1000>;
+ interrupts = <0 144 0x4>;
+ big-endian;
+ };
+
dspi0: dspi@2100000 {
compatible = "fsl,ls1043a-dspi", "fsl,ls1021a-v1.0-dspi";
#address-cells = <1>;
serial1 = &serial1;
};
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
};
&esdhc {
serial0 = &serial0;
serial1 = &serial1;
};
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
};
&esdhc {
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ dma-coherent;
num-lanes = <4>;
bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x10 0x00010000 0x0 0x00010000 /* downstream I/O */
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ dma-coherent;
num-lanes = <4>;
bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x12 0x00010000 0x0 0x00010000 /* downstream I/O */
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ dma-coherent;
num-lanes = <8>;
bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x14 0x00010000 0x0 0x00010000 /* downstream I/O */
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
+ dma-coherent;
num-lanes = <4>;
bus-range = <0x0 0xff>;
ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000 /* downstream I/O */
interrupts = <0 12 4>;
};
};
+
+ ddr1: memory-controller@1080000 {
+ compatible = "fsl,qoriq-memory-controller";
+ reg = <0x0 0x1080000 0x0 0x1000>;
+ interrupts = <0 17 0x4>;
+ little-endian;
+ };
+
+ ddr2: memory-controller@1090000 {
+ compatible = "fsl,qoriq-memory-controller";
+ reg = <0x0 0x1090000 0x0 0x1000>;
+ interrupts = <0 18 0x4>;
+ little-endian;
+ };
};
* Reserve below regions from memory node:
*
* 0x05e0,0000 - 0x05ef,ffff: MCU firmware runtime using
+ * 0x05f0,1000 - 0x05f0,1fff: Reboot reason
* 0x06df,f000 - 0x06df,ffff: Mailbox message data
* 0x0740,f000 - 0x0740,ffff: MCU firmware section
+ * 0x21f0,0000 - 0x21ff,ffff: pstore/ramoops buffer
* 0x3e00,0000 - 0x3fff,ffff: OP-TEE
*/
memory@0 {
device_type = "memory";
reg = <0x00000000 0x00000000 0x00000000 0x05e00000>,
- <0x00000000 0x05f00000 0x00000000 0x00eff000>,
+ <0x00000000 0x05f00000 0x00000000 0x00001000>,
+ <0x00000000 0x05f02000 0x00000000 0x00efd000>,
<0x00000000 0x06e00000 0x00000000 0x0060f000>,
- <0x00000000 0x07410000 0x00000000 0x36bf0000>;
+ <0x00000000 0x07410000 0x00000000 0x1aaf0000>,
+ <0x00000000 0x22000000 0x00000000 0x1c000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ramoops@0x21f00000 {
+ compatible = "ramoops";
+ reg = <0x0 0x21f00000 0x0 0x00100000>;
+ record-size = <0x00020000>;
+ console-size = <0x00020000>;
+ ftrace-size = <0x00020000>;
+ };
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ size = <0x00000000 0x08000000>;
+ linux,cma-default;
+ };
+ };
+
+ reboot-mode-syscon@5f01000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x0 0x05f01000 0x0 0x00001000>;
+
+ reboot-mode {
+ compatible = "syscon-reboot-mode";
+ offset = <0x0>;
+
+ mode-normal = <0x77665501>;
+ mode-bootloader = <0x77665500>;
+ mode-recovery = <0x77665502>;
+ };
};
soc {
};
uart1: uart@f7111000 {
+ assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
+ assigned-clock-rates = <150000000>;
status = "ok";
};
&uart3 {
label = "LS-UART1";
};
+
+&ade {
+ status = "ok";
+};
+
+&dsi {
+ status = "ok";
+
+ ports {
+ /* 1 for output port */
+ port@1 {
+ reg = <1>;
+
+ dsi_out0: endpoint@0 {
+ remote-endpoint = <&adv7533_in>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "ok";
+
+ adv7533: adv7533@39 {
+ compatible = "adi,adv7533";
+ reg = <0x39>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <1 2>;
+ pd-gpio = <&gpio0 4 0>;
+ adi,dsi-lanes = <4>;
+
+ port {
+ adv7533_in: endpoint {
+ remote-endpoint = <&dsi_out0>;
+ };
+ };
+ };
+};
#clock-cells = <1>;
};
+ medianoc_ade: medianoc_ade@f4520000 {
+ compatible = "syscon";
+ reg = <0x0 0xf4520000 0x0 0x4000>;
+ };
+
stub_clock: stub_clock {
compatible = "hisilicon,hi6220-stub-clk";
hisilicon,hi6220-clk-sram = <&sram>;
interrupts = <0x0 0x48 0x4>;
clocks = <&sys_ctrl 2>, <&sys_ctrl 1>;
clock-names = "ciu", "biu";
+ resets = <&sys_ctrl PERIPH_RSTDIS0_MMC0>;
bus-width = <0x8>;
vmmc-supply = <&ldo19>;
pinctrl-names = "default";
card-detect-delay = <200>;
hisilicon,peripheral-syscon = <&ao_ctrl>;
cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
reg = <0x0 0xf723e000 0x0 0x1000>;
interrupts = <0x0 0x49 0x4>;
#address-cells = <0x1>;
#size-cells = <0x0>;
clocks = <&sys_ctrl 4>, <&sys_ctrl 3>;
clock-names = "ciu", "biu";
+ resets = <&sys_ctrl PERIPH_RSTDIS0_MMC1>;
vqmmc-supply = <&ldo7>;
vmmc-supply = <&ldo10>;
bus-width = <0x4>;
interrupts = <0x0 0x4a 0x4>;
clocks = <&sys_ctrl HI6220_MMC2_CIUCLK>, <&sys_ctrl HI6220_MMC2_CLK>;
clock-names = "ciu", "biu";
+ resets = <&sys_ctrl PERIPH_RSTDIS0_MMC2>;
bus-width = <0x4>;
broken-cd;
pinctrl-names = "default", "idle";
};
};
};
+
+ ade: ade@f4100000 {
+ compatible = "hisilicon,hi6220-ade";
+ reg = <0x0 0xf4100000 0x0 0x7800>;
+ reg-names = "ade_base";
+ hisilicon,noc-syscon = <&medianoc_ade>;
+ resets = <&media_ctrl MEDIA_ADE>;
+ interrupts = <0 115 4>; /* ldi interrupt */
+
+ clocks = <&media_ctrl HI6220_ADE_CORE>,
+ <&media_ctrl HI6220_CODEC_JPEG>,
+ <&media_ctrl HI6220_ADE_PIX_SRC>;
+ /*clock name*/
+ clock-names = "clk_ade_core",
+ "clk_codec_jpeg",
+ "clk_ade_pix";
+
+ assigned-clocks = <&media_ctrl HI6220_ADE_CORE>,
+ <&media_ctrl HI6220_CODEC_JPEG>;
+ assigned-clock-rates = <360000000>, <288000000>;
+ dma-coherent;
+ status = "disabled";
+
+ port {
+ ade_out: endpoint {
+ remote-endpoint = <&dsi_in>;
+ };
+ };
+ };
+
+ dsi: dsi@f4107800 {
+ compatible = "hisilicon,hi6220-dsi";
+ reg = <0x0 0xf4107800 0x0 0x100>;
+ clocks = <&media_ctrl HI6220_DSI_PCLK>;
+ clock-names = "pclk";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 0 for input port */
+ port@0 {
+ reg = <0>;
+ dsi_in: endpoint {
+ remote-endpoint = <&ade_out>;
+ };
+ };
+ };
+ };
};
};
clock-frequency = <200000000>;
};
- peri_c_subctrl: syscon@80000000 {
- compatible = "hisilicon,hip05-perisubc", "syscon";
- reg = < 0x0 0x80000000 0x0 0x10000>;
- };
-
uart0: uart@80300000 {
compatible = "snps,dw-apb-uart";
reg = <0x0 0x80300000 0x0 0x10000>;
+++ /dev/null
-soc0: soc@000000000 {
- #address-cells = <2>;
- #size-cells = <2>;
- device_type = "soc";
- compatible = "simple-bus";
- ranges = <0x0 0x0 0x0 0x0 0x1 0x0>;
- chip-id = <0>;
-
- soc0_mdio0: mdio@803c0000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "hisilicon,hns-mdio";
- reg = <0x0 0x803c0000 0x0 0x10000>;
- subctrl-vbase = <&peri_c_subctrl>;
-
- soc0_phy0: ethernet-phy@0 {
- reg = <0x0>;
- compatible = "ethernet-phy-ieee802.3-c22";
- };
- soc0_phy1: ethernet-phy@1 {
- reg = <0x1>;
- compatible = "ethernet-phy-ieee802.3-c22";
- };
- };
-
- dsaf0: dsa@c7000000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "hisilicon,hns-dsaf-v1";
- mode = "6port-16rss";
- interrupt-parent = <&mbigen_dsa>;
-
- reg = <0x0 0xc5000000 0x0 0x890000
- 0x0 0xc7000000 0x0 0x60000
- >;
-
- reg-names = "ppe-base","dsaf-base";
- subctrl-syscon = <&dsaf_subctrl>;
- reset-field-offset = <0>;
- interrupts = <
- /* [14] ge fifo err 8 / xge 6**/
- 149 0x4 150 0x4 151 0x4 152 0x4
- 153 0x4 154 0x4 26 0x4 27 0x4
- 155 0x4 156 0x4 157 0x4 158 0x4 159 0x4 160 0x4
- /* [12] rcb com 4*3**/
- 0x6 0x4 0x7 0x4 0x8 0x4 0x9 0x4
- 16 0x4 17 0x4 18 0x4 19 0x4
- 22 0x4 23 0x4 24 0x4 25 0x4
- /* [8] ppe tnl 0-7***/
- 0x0 0x4 0x1 0x4 0x2 0x4 0x3 0x4
- 0x4 0x4 0x5 0x4 12 0x4 13 0x4
- /* [21] dsaf event int 3+18**/
- 128 0x4 129 0x4 130 0x4
- 0x83 0x4 0x84 0x4 0x85 0x4 0x86 0x4 0x87 0x4 0x88 0x4
- 0x89 0x4 0x8a 0x4 0x8b 0x4 0x8c 0x4 0x8d 0x4 0x8e 0x4
- 0x8f 0x4 0x90 0x4 0x91 0x4 0x92 0x4 0x93 0x4 0x94 0x4
- /* [4] debug rcb 2*2*/
- 0xe 0x1 0xf 0x1 0x14 0x1 0x15 0x1
- /* [256] sevice rcb 2*128*/
- 0x180 0x1 0x181 0x1 0x182 0x1 0x183 0x1
- 0x184 0x1 0x185 0x1 0x186 0x1 0x187 0x1
- 0x188 0x1 0x189 0x1 0x18a 0x1 0x18b 0x1
- 0x18c 0x1 0x18d 0x1 0x18e 0x1 0x18f 0x1
- 0x190 0x1 0x191 0x1 0x192 0x1 0x193 0x1
- 0x194 0x1 0x195 0x1 0x196 0x1 0x197 0x1
- 0x198 0x1 0x199 0x1 0x19a 0x1 0x19b 0x1
- 0x19c 0x1 0x19d 0x1 0x19e 0x1 0x19f 0x1
- 0x1a0 0x1 0x1a1 0x1 0x1a2 0x1 0x1a3 0x1
- 0x1a4 0x1 0x1a5 0x1 0x1a6 0x1 0x1a7 0x1
- 0x1a8 0x1 0x1a9 0x1 0x1aa 0x1 0x1ab 0x1
- 0x1ac 0x1 0x1ad 0x1 0x1ae 0x1 0x1af 0x1
- 0x1b0 0x1 0x1b1 0x1 0x1b2 0x1 0x1b3 0x1
- 0x1b4 0x1 0x1b5 0x1 0x1b6 0x1 0x1b7 0x1
- 0x1b8 0x1 0x1b9 0x1 0x1ba 0x1 0x1bb 0x1
- 0x1bc 0x1 0x1bd 0x1 0x1be 0x1 0x1bf 0x1
- 0x1c0 0x1 0x1c1 0x1 0x1c2 0x1 0x1c3 0x1
- 0x1c4 0x1 0x1c5 0x1 0x1c6 0x1 0x1c7 0x1
- 0x1c8 0x1 0x1c9 0x1 0x1ca 0x1 0x1cb 0x1
- 0x1cc 0x1 0x1cd 0x1 0x1ce 0x1 0x1cf 0x1
- 0x1d0 0x1 0x1d1 0x1 0x1d2 0x1 0x1d3 0x1
- 0x1d4 0x1 0x1d5 0x1 0x1d6 0x1 0x1d7 0x1
- 0x1d8 0x1 0x1d9 0x1 0x1da 0x1 0x1db 0x1
- 0x1dc 0x1 0x1dd 0x1 0x1de 0x1 0x1df 0x1
- 0x1e0 0x1 0x1e1 0x1 0x1e2 0x1 0x1e3 0x1
- 0x1e4 0x1 0x1e5 0x1 0x1e6 0x1 0x1e7 0x1
- 0x1e8 0x1 0x1e9 0x1 0x1ea 0x1 0x1eb 0x1
- 0x1ec 0x1 0x1ed 0x1 0x1ee 0x1 0x1ef 0x1
- 0x1f0 0x1 0x1f1 0x1 0x1f2 0x1 0x1f3 0x1
- 0x1f4 0x1 0x1f5 0x1 0x1f6 0x1 0x1f7 0x1
- 0x1f8 0x1 0x1f9 0x1 0x1fa 0x1 0x1fb 0x1
- 0x1fc 0x1 0x1fd 0x1 0x1fe 0x1 0x1ff 0x1
- 0x200 0x1 0x201 0x1 0x202 0x1 0x203 0x1
- 0x204 0x1 0x205 0x1 0x206 0x1 0x207 0x1
- 0x208 0x1 0x209 0x1 0x20a 0x1 0x20b 0x1
- 0x20c 0x1 0x20d 0x1 0x20e 0x1 0x20f 0x1
- 0x210 0x1 0x211 0x1 0x212 0x1 0x213 0x1
- 0x214 0x1 0x215 0x1 0x216 0x1 0x217 0x1
- 0x218 0x1 0x219 0x1 0x21a 0x1 0x21b 0x1
- 0x21c 0x1 0x21d 0x1 0x21e 0x1 0x21f 0x1
- 0x220 0x1 0x221 0x1 0x222 0x1 0x223 0x1
- 0x224 0x1 0x225 0x1 0x226 0x1 0x227 0x1
- 0x228 0x1 0x229 0x1 0x22a 0x1 0x22b 0x1
- 0x22c 0x1 0x22d 0x1 0x22e 0x1 0x22f 0x1
- 0x230 0x1 0x231 0x1 0x232 0x1 0x233 0x1
- 0x234 0x1 0x235 0x1 0x236 0x1 0x237 0x1
- 0x238 0x1 0x239 0x1 0x23a 0x1 0x23b 0x1
- 0x23c 0x1 0x23d 0x1 0x23e 0x1 0x23f 0x1
- 0x240 0x1 0x241 0x1 0x242 0x1 0x243 0x1
- 0x244 0x1 0x245 0x1 0x246 0x1 0x247 0x1
- 0x248 0x1 0x249 0x1 0x24a 0x1 0x24b 0x1
- 0x24c 0x1 0x24d 0x1 0x24e 0x1 0x24f 0x1
- 0x250 0x1 0x251 0x1 0x252 0x1 0x253 0x1
- 0x254 0x1 0x255 0x1 0x256 0x1 0x257 0x1
- 0x258 0x1 0x259 0x1 0x25a 0x1 0x25b 0x1
- 0x25c 0x1 0x25d 0x1 0x25e 0x1 0x25f 0x1
- 0x260 0x1 0x261 0x1 0x262 0x1 0x263 0x1
- 0x264 0x1 0x265 0x1 0x266 0x1 0x267 0x1
- 0x268 0x1 0x269 0x1 0x26a 0x1 0x26b 0x1
- 0x26c 0x1 0x26d 0x1 0x26e 0x1 0x26f 0x1
- 0x270 0x1 0x271 0x1 0x272 0x1 0x273 0x1
- 0x274 0x1 0x275 0x1 0x276 0x1 0x277 0x1
- 0x278 0x1 0x279 0x1 0x27a 0x1 0x27b 0x1
- 0x27c 0x1 0x27d 0x1 0x27e 0x1 0x27f 0x1>;
- buf-size = <4096>;
- desc-num = <1024>;
- dma-coherent;
-
- port@0 {
- reg = <0>;
- serdes-syscon = <&serdes_ctrl0>;
- };
- port@1 {
- reg = <1>;
- serdes-syscon = <&serdes_ctrl0>;
- };
- port@4 {
- reg = <4>;
- phy-handle = <&soc0_phy0>;
- serdes-syscon = <&serdes_ctrl1>;
- };
- port@5 {
- reg = <5>;
- phy-handle = <&soc0_phy1>;
- serdes-syscon = <&serdes_ctrl1>;
- };
- };
-
- eth0: ethernet@0{
- compatible = "hisilicon,hns-nic-v1";
- ae-handle = <&dsaf0>;
- port-idx-in-ae = <0>;
- local-mac-address = [00 00 00 01 00 58];
- status = "disabled";
- dma-coherent;
- };
- eth1: ethernet@1{
- compatible = "hisilicon,hns-nic-v1";
- ae-handle = <&dsaf0>;
- port-idx-in-ae = <1>;
- local-mac-address = [00 00 00 01 00 59];
- status = "disabled";
- dma-coherent;
- };
- eth2: ethernet@4{
- compatible = "hisilicon,hns-nic-v1";
- ae-handle = <&dsaf0>;
- port-idx-in-ae = <4>;
- local-mac-address = [00 00 00 01 00 5a];
- status = "disabled";
- dma-coherent;
- };
- eth3: ethernet@5{
- compatible = "hisilicon,hns-nic-v1";
- ae-handle = <&dsaf0>;
- port-idx-in-ae = <5>;
- local-mac-address = [00 00 00 01 00 5b];
- status = "disabled";
- dma-coherent;
- };
-};
chosen { };
};
+ð0 {
+ status = "ok";
+};
+
+ð1 {
+ status = "ok";
+};
+
+ð2 {
+ status = "ok";
+};
+
+ð3 {
+ status = "ok";
+};
+
+&sas0 {
+ status = "ok";
+};
+
+&sas1 {
+ status = "ok";
+};
+
+&sas2 {
+ status = "ok";
+};
+
&usb_ohci {
status = "ok";
};
#interrupt-cells = <2>;
num-pins = <2>;
};
+
+ mbigen_sas1: intc_sas1 {
+ msi-parent = <&its_dsa 0x40000>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ num-pins = <128>;
+ };
+
+ mbigen_sas2: intc_sas2 {
+ msi-parent = <&its_dsa 0x40040>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ num-pins = <128>;
+ };
+ };
+
+ mbigen_dsa@c0080000 {
+ compatible = "hisilicon,mbigen-v2";
+ reg = <0x0 0xc0080000 0x0 0x10000>;
+
+ mbigen_dsaf0: intc_dsaf0 {
+ msi-parent = <&its_dsa 0x40800>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ num-pins = <409>;
+ };
+
+ mbigen_sas0: intc-sas0 {
+ msi-parent = <&its_dsa 0x40900>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ num-pins = <128>;
+ };
};
soc {
dma-coherent;
status = "disabled";
};
+
+ peri_c_subctrl: sub_ctrl_c@60000000 {
+ compatible = "hisilicon,peri-subctrl","syscon";
+ reg = <0 0x60000000 0x0 0x10000>;
+ };
+
+ dsa_subctrl: dsa_subctrl@c0000000 {
+ compatible = "hisilicon,dsa-subctrl", "syscon";
+ reg = <0x0 0xc0000000 0x0 0x10000>;
+ };
+
+ pcie_subctl: pcie_subctl@a0000000 {
+ compatible = "hisilicon,pcie-sas-subctrl", "syscon";
+ reg = <0x0 0xa0000000 0x0 0x10000>;
+ };
+
+ serdes_ctrl: sds_ctrl@c2200000 {
+ compatible = "syscon";
+ reg = <0 0xc2200000 0x0 0x80000>;
+ };
+
+ mdio@603c0000 {
+ compatible = "hisilicon,hns-mdio";
+ reg = <0x0 0x603c0000 0x0 0x1000>;
+ subctrl-vbase = <&peri_c_subctrl 0x338 0xa38 0x531c 0x5a1c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+
+ dsaf0: dsa@c7000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "hisilicon,hns-dsaf-v2";
+ mode = "6port-16rss";
+ reg = <0x0 0xc5000000 0x0 0x890000
+ 0x0 0xc7000000 0x0 0x600000>;
+ reg-names = "ppe-base", "dsaf-base";
+ interrupt-parent = <&mbigen_dsaf0>;
+ subctrl-syscon = <&dsa_subctrl>;
+ reset-field-offset = <0>;
+ interrupts =
+ <576 1>, <577 1>, <578 1>, <579 1>, <580 1>,
+ <581 1>, <582 1>, <583 1>, <584 1>, <585 1>,
+ <586 1>, <587 1>, <588 1>, <589 1>, <590 1>,
+ <591 1>, <592 1>, <593 1>, <594 1>, <595 1>,
+ <596 1>, <597 1>, <598 1>, <599 1>, <600 1>,
+ <960 1>, <961 1>, <962 1>, <963 1>, <964 1>,
+ <965 1>, <966 1>, <967 1>, <968 1>, <969 1>,
+ <970 1>, <971 1>, <972 1>, <973 1>, <974 1>,
+ <975 1>, <976 1>, <977 1>, <978 1>, <979 1>,
+ <980 1>, <981 1>, <982 1>, <983 1>, <984 1>,
+ <985 1>, <986 1>, <987 1>, <988 1>, <989 1>,
+ <990 1>, <991 1>, <992 1>, <993 1>, <994 1>,
+ <995 1>, <996 1>, <997 1>, <998 1>, <999 1>,
+ <1000 1>, <1001 1>, <1002 1>, <1003 1>, <1004 1>,
+ <1005 1>, <1006 1>, <1007 1>, <1008 1>, <1009 1>,
+ <1010 1>, <1011 1>, <1012 1>, <1013 1>, <1014 1>,
+ <1015 1>, <1016 1>, <1017 1>, <1018 1>, <1019 1>,
+ <1020 1>, <1021 1>, <1022 1>, <1023 1>, <1024 1>,
+ <1025 1>, <1026 1>, <1027 1>, <1028 1>, <1029 1>,
+ <1030 1>, <1031 1>, <1032 1>, <1033 1>, <1034 1>,
+ <1035 1>, <1036 1>, <1037 1>, <1038 1>, <1039 1>,
+ <1040 1>, <1041 1>, <1042 1>, <1043 1>, <1044 1>,
+ <1045 1>, <1046 1>, <1047 1>, <1048 1>, <1049 1>,
+ <1050 1>, <1051 1>, <1052 1>, <1053 1>, <1054 1>,
+ <1055 1>, <1056 1>, <1057 1>, <1058 1>, <1059 1>,
+ <1060 1>, <1061 1>, <1062 1>, <1063 1>, <1064 1>,
+ <1065 1>, <1066 1>, <1067 1>, <1068 1>, <1069 1>,
+ <1070 1>, <1071 1>, <1072 1>, <1073 1>, <1074 1>,
+ <1075 1>, <1076 1>, <1077 1>, <1078 1>, <1079 1>,
+ <1080 1>, <1081 1>, <1082 1>, <1083 1>, <1084 1>,
+ <1085 1>, <1086 1>, <1087 1>, <1088 1>, <1089 1>,
+ <1090 1>, <1091 1>, <1092 1>, <1093 1>, <1094 1>,
+ <1095 1>, <1096 1>, <1097 1>, <1098 1>, <1099 1>,
+ <1100 1>, <1101 1>, <1102 1>, <1103 1>, <1104 1>,
+ <1105 1>, <1106 1>, <1107 1>, <1108 1>, <1109 1>,
+ <1110 1>, <1111 1>, <1112 1>, <1113 1>, <1114 1>,
+ <1115 1>, <1116 1>, <1117 1>, <1118 1>, <1119 1>,
+ <1120 1>, <1121 1>, <1122 1>, <1123 1>, <1124 1>,
+ <1125 1>, <1126 1>, <1127 1>, <1128 1>, <1129 1>,
+ <1130 1>, <1131 1>, <1132 1>, <1133 1>, <1134 1>,
+ <1135 1>, <1136 1>, <1137 1>, <1138 1>, <1139 1>,
+ <1140 1>, <1141 1>, <1142 1>, <1143 1>, <1144 1>,
+ <1145 1>, <1146 1>, <1147 1>, <1148 1>, <1149 1>,
+ <1150 1>, <1151 1>, <1152 1>, <1153 1>, <1154 1>,
+ <1155 1>, <1156 1>, <1157 1>, <1158 1>, <1159 1>,
+ <1160 1>, <1161 1>, <1162 1>, <1163 1>, <1164 1>,
+ <1165 1>, <1166 1>, <1167 1>, <1168 1>, <1169 1>,
+ <1170 1>, <1171 1>, <1172 1>, <1173 1>, <1174 1>,
+ <1175 1>, <1176 1>, <1177 1>, <1178 1>, <1179 1>,
+ <1180 1>, <1181 1>, <1182 1>, <1183 1>, <1184 1>,
+ <1185 1>, <1186 1>, <1187 1>, <1188 1>, <1189 1>,
+ <1190 1>, <1191 1>, <1192 1>, <1193 1>, <1194 1>,
+ <1195 1>, <1196 1>, <1197 1>, <1198 1>, <1199 1>,
+ <1200 1>, <1201 1>, <1202 1>, <1203 1>, <1204 1>,
+ <1205 1>, <1206 1>, <1207 1>, <1208 1>, <1209 1>,
+ <1210 1>, <1211 1>, <1212 1>, <1213 1>, <1214 1>,
+ <1215 1>, <1216 1>, <1217 1>, <1218 1>, <1219 1>,
+ <1220 1>, <1221 1>, <1222 1>, <1223 1>, <1224 1>,
+ <1225 1>, <1226 1>, <1227 1>, <1228 1>, <1229 1>,
+ <1230 1>, <1231 1>, <1232 1>, <1233 1>, <1234 1>,
+ <1235 1>, <1236 1>, <1237 1>, <1238 1>, <1239 1>,
+ <1240 1>, <1241 1>, <1242 1>, <1243 1>, <1244 1>,
+ <1245 1>, <1246 1>, <1247 1>, <1248 1>, <1249 1>,
+ <1250 1>, <1251 1>, <1252 1>, <1253 1>, <1254 1>,
+ <1255 1>, <1256 1>, <1257 1>, <1258 1>, <1259 1>,
+ <1260 1>, <1261 1>, <1262 1>, <1263 1>, <1264 1>,
+ <1265 1>, <1266 1>, <1267 1>, <1268 1>, <1269 1>,
+ <1270 1>, <1271 1>, <1272 1>, <1273 1>, <1274 1>,
+ <1275 1>, <1276 1>, <1277 1>, <1278 1>, <1279 1>,
+ <1280 1>, <1281 1>, <1282 1>, <1283 1>, <1284 1>,
+ <1285 1>, <1286 1>, <1287 1>, <1288 1>, <1289 1>,
+ <1290 1>, <1291 1>, <1292 1>, <1293 1>, <1294 1>,
+ <1295 1>, <1296 1>, <1297 1>, <1298 1>, <1299 1>,
+ <1300 1>, <1301 1>, <1302 1>, <1303 1>, <1304 1>,
+ <1305 1>, <1306 1>, <1307 1>, <1308 1>, <1309 1>,
+ <1310 1>, <1311 1>, <1312 1>, <1313 1>, <1314 1>,
+ <1315 1>, <1316 1>, <1317 1>, <1318 1>, <1319 1>,
+ <1320 1>, <1321 1>, <1322 1>, <1323 1>, <1324 1>,
+ <1325 1>, <1326 1>, <1327 1>, <1328 1>, <1329 1>,
+ <1330 1>, <1331 1>, <1332 1>, <1333 1>, <1334 1>,
+ <1335 1>, <1336 1>, <1337 1>, <1338 1>, <1339 1>,
+ <1340 1>, <1341 1>, <1342 1>, <1343 1>;
+
+ desc-num = <0x400>;
+ buf-size = <0x1000>;
+ dma-coherent;
+
+ port@0 {
+ reg = <0>;
+ serdes-syscon = <&serdes_ctrl>;
+ port-rst-offset = <0>;
+ port-mode-offset = <0>;
+ media-type = "fiber";
+ };
+
+ port@1 {
+ reg = <1>;
+ serdes-syscon= <&serdes_ctrl>;
+ port-rst-offset = <1>;
+ port-mode-offset = <1>;
+ media-type = "fiber";
+ };
+
+ port@4 {
+ reg = <4>;
+ phy-handle = <&phy0>;
+ serdes-syscon= <&serdes_ctrl>;
+ port-rst-offset = <4>;
+ port-mode-offset = <2>;
+ media-type = "copper";
+ };
+
+ port@5 {
+ reg = <5>;
+ phy-handle = <&phy1>;
+ serdes-syscon= <&serdes_ctrl>;
+ port-rst-offset = <5>;
+ port-mode-offset = <3>;
+ media-type = "copper";
+ };
+ };
+
+ eth0: ethernet@4{
+ compatible = "hisilicon,hns-nic-v2";
+ ae-handle = <&dsaf0>;
+ port-idx-in-ae = <4>;
+ local-mac-address = [00 00 00 00 00 00];
+ status = "disabled";
+ dma-coherent;
+ };
+
+ eth1: ethernet@5{
+ compatible = "hisilicon,hns-nic-v2";
+ ae-handle = <&dsaf0>;
+ port-idx-in-ae = <5>;
+ local-mac-address = [00 00 00 00 00 00];
+ status = "disabled";
+ dma-coherent;
+ };
+
+ eth2: ethernet@0{
+ compatible = "hisilicon,hns-nic-v2";
+ ae-handle = <&dsaf0>;
+ port-idx-in-ae = <0>;
+ local-mac-address = [00 00 00 00 00 00];
+ status = "disabled";
+ dma-coherent;
+ };
+
+ eth3: ethernet@1{
+ compatible = "hisilicon,hns-nic-v2";
+ ae-handle = <&dsaf0>;
+ port-idx-in-ae = <1>;
+ local-mac-address = [00 00 00 00 00 00];
+ status = "disabled";
+ dma-coherent;
+ };
+
+ sas0: sas@c3000000 {
+ compatible = "hisilicon,hip06-sas-v2";
+ reg = <0 0xc3000000 0 0x10000>;
+ sas-addr = [50 01 88 20 16 00 00 00];
+ hisilicon,sas-syscon = <&dsa_subctrl>;
+ ctrl-reset-reg = <0xa60>;
+ ctrl-reset-sts-reg = <0x5a30>;
+ ctrl-clock-ena-reg = <0x338>;
+ queue-count = <16>;
+ phy-count = <8>;
+ dma-coherent;
+ interrupt-parent = <&mbigen_sas0>;
+ interrupts = <64 4>,<65 4>,<66 4>,<67 4>,<68 4>,
+ <69 4>,<70 4>,<71 4>,<72 4>,<73 4>,
+ <75 4>,<76 4>,<77 4>,<78 4>,<79 4>,
+ <80 4>,<81 4>,<82 4>,<83 4>,<84 4>,
+ <85 4>,<86 4>,<87 4>,<88 4>,<89 4>,
+ <90 4>,<91 4>,<92 4>,<93 4>,<94 4>,
+ <95 4>,<96 4>,<97 4>,<98 4>,<99 4>,
+ <100 4>,<101 4>,<102 4>,<103 4>,<104 4>,
+ <105 4>,<106 4>,<107 4>,<108 4>,<109 4>,
+ <110 4>,<111 4>,<112 4>,<113 4>,<114 4>,
+ <115 4>,<116 4>,<117 4>,<118 4>,<119 4>,
+ <120 4>,<121 4>,<122 4>,<123 4>,<124 4>,
+ <125 4>,<126 4>,<127 4>,<128 4>,<129 4>,
+ <130 4>,<131 4>,<132 4>,<133 4>,<134 4>,
+ <135 4>,<136 4>,<137 4>,<138 4>,<139 4>,
+ <140 4>,<141 4>,<142 4>,<143 4>,<144 4>,
+ <145 4>,<146 4>,<147 4>,<148 4>,<149 4>,
+ <150 4>,<151 4>,<152 4>,<153 4>,<154 4>,
+ <155 4>,<156 4>,<157 4>,<158 4>,<159 4>,
+ <160 4>,<601 1>,<602 1>,<603 1>,<604 1>,
+ <605 1>,<606 1>,<607 1>,<608 1>,<609 1>,
+ <610 1>,<611 1>,<612 1>,<613 1>,<614 1>,
+ <615 1>,<616 1>,<617 1>,<618 1>,<619 1>,
+ <620 1>,<621 1>,<622 1>,<623 1>,<624 1>,
+ <625 1>,<626 1>,<627 1>,<628 1>,<629 1>,
+ <630 1>,<631 1>,<632 1>;
+ status = "disabled";
+ };
+
+ sas1: sas@a2000000 {
+ compatible = "hisilicon,hip06-sas-v2";
+ reg = <0 0xa2000000 0 0x10000>;
+ sas-addr = [50 01 88 20 16 00 00 00];
+ hisilicon,sas-syscon = <&pcie_subctl>;
+ am-max-trans;
+ ctrl-reset-reg = <0xa18>;
+ ctrl-reset-sts-reg = <0x5a0c>;
+ ctrl-clock-ena-reg = <0x318>;
+ queue-count = <16>;
+ phy-count = <8>;
+ dma-coherent;
+ interrupt-parent = <&mbigen_sas1>;
+ interrupts = <64 4>,<65 4>,<66 4>,<67 4>,<68 4>,
+ <69 4>,<70 4>,<71 4>,<72 4>,<73 4>,
+ <74 4>,<75 4>,<76 4>,<77 4>,<78 4>,
+ <79 4>,<80 4>,<81 4>,<82 4>,<83 4>,
+ <84 4>,<85 4>,<86 4>,<87 4>,<88 4>,
+ <89 4>,<90 4>,<91 4>,<92 4>,<93 4>,
+ <94 4>,<95 4>,<96 4>,<97 4>,<98 4>,
+ <99 4>,<100 4>,<101 4>,<102 4>,<103 4>,
+ <104 4>,<105 4>,<106 4>,<107 4>,<108 4>,
+ <109 4>,<110 4>,<111 4>,<112 4>,<113 4>,
+ <114 4>,<115 4>,<116 4>,<117 4>,<118 4>,
+ <119 4>,<120 4>,<121 4>,<122 4>,<123 4>,
+ <124 4>,<125 4>,<126 4>,<127 4>,<128 4>,
+ <129 4>,<130 4>,<131 4>,<132 4>,<133 4>,
+ <134 4>,<135 4>,<136 4>,<137 4>,<138 4>,
+ <139 4>,<140 4>,<141 4>,<142 4>,<143 4>,
+ <144 4>,<145 4>,<146 4>,<147 4>,<148 4>,
+ <149 4>,<150 4>,<151 4>,<152 4>,<153 4>,
+ <154 4>,<155 4>,<156 4>,<157 4>,<158 4>,
+ <159 4>,<576 1>,<577 1>,<578 1>,<579 1>,
+ <580 1>,<581 1>,<582 1>,<583 1>,<584 1>,
+ <585 1>,<586 1>,<587 1>,<588 1>,<589 1>,
+ <590 1>,<591 1>,<592 1>,<593 1>,<594 1>,
+ <595 1>,<596 1>,<597 1>,<598 1>,<599 1>,
+ <600 1>,<601 1>,<602 1>,<603 1>,<604 1>,
+ <605 1>,<606 1>,<607 1>;
+ status = "disabled";
+ };
+
+ sas2: sas@a3000000 {
+ compatible = "hisilicon,hip06-sas-v2";
+ reg = <0 0xa3000000 0 0x10000>;
+ sas-addr = [50 01 88 20 16 00 00 00];
+ hisilicon,sas-syscon = <&pcie_subctl>;
+ ctrl-reset-reg = <0xae0>;
+ ctrl-reset-sts-reg = <0x5a70>;
+ ctrl-clock-ena-reg = <0x3a8>;
+ queue-count = <16>;
+ phy-count = <9>;
+ dma-coherent;
+ interrupt-parent = <&mbigen_sas2>;
+ interrupts = <192 4>,<193 4>,<194 4>,<195 4>,<196 4>,
+ <197 4>,<198 4>,<199 4>,<200 4>,<201 4>,
+ <202 4>,<203 4>,<204 4>,<205 4>,<206 4>,
+ <207 4>,<208 4>,<209 4>,<210 4>,<211 4>,
+ <212 4>,<213 4>,<214 4>,<215 4>,<216 4>,
+ <217 4>,<218 4>,<219 4>,<220 4>,<221 4>,
+ <222 4>,<223 4>,<224 4>,<225 4>,<226 4>,
+ <227 4>,<228 4>,<229 4>,<230 4>,<231 4>,
+ <232 4>,<233 4>,<234 4>,<235 4>,<236 4>,
+ <237 4>,<238 4>,<239 4>,<240 4>,<241 4>,
+ <242 4>,<243 4>,<244 4>,<245 4>,<246 4>,
+ <247 4>,<248 4>,<249 4>,<250 4>,<251 4>,
+ <252 4>,<253 4>,<254 4>,<255 4>,<256 4>,
+ <257 4>,<258 4>,<259 4>,<260 4>,<261 4>,
+ <262 4>,<263 4>,<264 4>,<265 4>,<266 4>,
+ <267 4>,<268 4>,<269 4>,<270 4>,<271 4>,
+ <272 4>,<273 4>,<274 4>,<275 4>,<276 4>,
+ <277 4>,<278 4>,<279 4>,<280 4>,<281 4>,
+ <282 4>,<283 4>,<284 4>,<285 4>,<286 4>,
+ <287 4>,<608 1>,<609 1>,<610 1>,<611 1>,
+ <612 1>,<613 1>,<614 1>,<615 1>,<616 1>,
+ <617 1>,<618 1>,<619 1>,<620 1>,<621 1>,
+ <622 1>,<623 1>,<624 1>,<625 1>,<626 1>,
+ <627 1>,<628 1>,<629 1>,<630 1>,<631 1>,
+ <632 1>,<633 1>,<634 1>,<635 1>,<636 1>,
+ <637 1>,<638 1>,<639 1>;
+ status = "disabled";
+ };
};
};
# Mvebu SoC Family
dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
#include "armada-ap806-dual.dtsi"
#include "armada-cp110-master.dtsi"
+#include "armada-cp110-slave.dtsi"
/ {
model = "Marvell Armada 8020";
--- /dev/null
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * Device Tree file for Marvell Armada 8040 Development board platform
+ */
+
+#include "armada-8040.dtsi"
+
+/ {
+ model = "Marvell Armada 8040 DB board";
+ compatible = "marvell,armada8040-db", "marvell,armada8040",
+ "marvell,armada-ap806-quad", "marvell,armada-ap806";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@00000000 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x200000>;
+ };
+ partition@400000 {
+ label = "Filesystem";
+ reg = <0x200000 0xce0000>;
+ };
+ };
+ };
+};
+
+/* Accessible over the mini-USB CON9 connector on the main board */
+&uart0 {
+ status = "okay";
+};
+
+
+/* CON5 on CP0 expansion */
+&cpm_pcie2 {
+ status = "okay";
+};
+
+&cpm_i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+/* CON4 on CP0 expansion */
+&cpm_sata0 {
+ status = "okay";
+};
+
+/* CON9 on CP0 expansion */
+&cpm_usb3_0 {
+ status = "okay";
+};
+
+/* CON10 on CP0 expansion */
+&cpm_usb3_1 {
+ status = "okay";
+};
+
+/* CON5 on CP1 expansion */
+&cps_pcie2 {
+ status = "okay";
+};
+
+&cps_i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+};
+
+/* CON4 on CP1 expansion */
+&cps_sata0 {
+ status = "okay";
+};
+
+/* CON9 on CP1 expansion */
+&cps_usb3_0 {
+ status = "okay";
+};
+
+/* CON10 on CP1 expansion */
+&cps_usb3_1 {
+ status = "okay";
+};
#include "armada-ap806-quad.dtsi"
#include "armada-cp110-master.dtsi"
+#include "armada-cp110-slave.dtsi"
/ {
model = "Marvell Armada 8040";
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
+ pmu {
+ compatible = "arm,cortex-a72-pmu";
+ interrupt-parent = <&pic>;
+ interrupts = <17>;
+ };
+
odmi: odmi@300000 {
compatible = "marvell,odmi-controller";
interrupt-controller;
marvell,spi-base = <128>, <136>, <144>, <152>;
};
+ pic: interrupt-controller@3f0100 {
+ compatible = "marvell,armada-8k-pic";
+ reg = <0x3f0100 0x10>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
xor@400000 {
compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
reg = <0x400000 0x1000>,
#interrupt-cells = <1>;
device_type = "pci";
dma-coherent;
+ msi-parent = <&gic_v2m0>;
bus-range = <0 0xff>;
ranges =
#interrupt-cells = <1>;
device_type = "pci";
dma-coherent;
+ msi-parent = <&gic_v2m0>;
bus-range = <0 0xff>;
ranges =
#interrupt-cells = <1>;
device_type = "pci";
dma-coherent;
+ msi-parent = <&gic_v2m0>;
bus-range = <0 0xff>;
ranges =
--- /dev/null
+/*
+ * Copyright (C) 2016 Marvell Technology Group Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPLv2 or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * Device Tree file for Marvell Armada CP110 Slave.
+ */
+
+/ {
+ cp110-slave {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges;
+
+ config-space {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gic>;
+ ranges = <0x0 0x0 0xf4000000 0x2000000>;
+
+ cps_syscon0: system-controller@440000 {
+ compatible = "marvell,cp110-system-controller0",
+ "syscon";
+ reg = <0x440000 0x1000>;
+ #clock-cells = <2>;
+ core-clock-output-names =
+ "cps-apll", "cps-ppv2-core", "cps-eip",
+ "cps-core", "cps-nand-core";
+ gate-clock-output-names =
+ "cps-audio", "cps-communit", "cps-nand",
+ "cps-ppv2", "cps-sdio", "cps-mg-domain",
+ "cps-mg-core", "cps-xor1", "cps-xor0",
+ "cps-gop-dp", "none", "cps-pcie_x10",
+ "cps-pcie_x11", "cps-pcie_x4", "cps-pcie-xor",
+ "cps-sata", "cps-sata-usb", "cps-main",
+ "cps-sd-mmc", "none", "none",
+ "cps-slow-io", "cps-usb3h0", "cps-usb3h1",
+ "cps-usb3dev", "cps-eip150", "cps-eip197";
+ };
+
+ cps_sata0: sata@540000 {
+ compatible = "marvell,armada-8k-ahci";
+ reg = <0x540000 0x30000>;
+ interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cps_syscon0 1 15>;
+ status = "disabled";
+ };
+
+ cps_usb3_0: usb3@500000 {
+ compatible = "marvell,armada-8k-xhci",
+ "generic-xhci";
+ reg = <0x500000 0x4000>;
+ dma-coherent;
+ interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cps_syscon0 1 22>;
+ status = "disabled";
+ };
+
+ cps_usb3_1: usb3@510000 {
+ compatible = "marvell,armada-8k-xhci",
+ "generic-xhci";
+ reg = <0x510000 0x4000>;
+ dma-coherent;
+ interrupts = <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cps_syscon0 1 23>;
+ status = "disabled";
+ };
+
+ cps_xor0: xor@6a0000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x6a0000 0x1000>,
+ <0x6b0000 0x1000>;
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+ clocks = <&cps_syscon0 1 8>;
+ };
+
+ cps_xor1: xor@6c0000 {
+ compatible = "marvell,armada-7k-xor", "marvell,xor-v2";
+ reg = <0x6c0000 0x1000>,
+ <0x6d0000 0x1000>;
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+ clocks = <&cps_syscon0 1 7>;
+ };
+
+ cps_spi0: spi@700600 {
+ compatible = "marvell,armada-380-spi";
+ reg = <0x700600 0x50>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ cell-index = <1>;
+ clocks = <&cps_syscon0 0 3>;
+ status = "disabled";
+ };
+
+ cps_spi1: spi@700680 {
+ compatible = "marvell,armada-380-spi";
+ reg = <0x700680 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <2>;
+ clocks = <&cps_syscon0 1 21>;
+ status = "disabled";
+ };
+
+ cps_i2c0: i2c@701000 {
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x701000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cps_syscon0 1 21>;
+ status = "disabled";
+ };
+
+ cps_i2c1: i2c@701100 {
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x701100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cps_syscon0 1 21>;
+ status = "disabled";
+ };
+ };
+
+ cps_pcie0: pcie@f4600000 {
+ compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+ reg = <0 0xf4600000 0 0x10000>,
+ <0 0xfaf00000 0 0x80000>;
+ reg-names = "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+
+ bus-range = <0 0xff>;
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 0xfd000000 0 0xfd000000 0 0x10000
+ /* non-prefetchable memory */
+ 0x82000000 0 0xfa000000 0 0xfa000000 0 0xf00000>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
+ num-lanes = <1>;
+ clocks = <&cps_syscon0 1 13>;
+ status = "disabled";
+ };
+
+ cps_pcie1: pcie@f4620000 {
+ compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+ reg = <0 0xf4620000 0 0x10000>,
+ <0 0xfbf00000 0 0x80000>;
+ reg-names = "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+
+ bus-range = <0 0xff>;
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 0xfd010000 0 0xfd010000 0 0x10000
+ /* non-prefetchable memory */
+ 0x82000000 0 0xfb000000 0 0xfb000000 0 0xf00000>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>;
+
+ num-lanes = <1>;
+ clocks = <&cps_syscon0 1 11>;
+ status = "disabled";
+ };
+
+ cps_pcie2: pcie@f4640000 {
+ compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+ reg = <0 0xf4640000 0 0x10000>,
+ <0 0xfcf00000 0 0x80000>;
+ reg-names = "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ dma-coherent;
+ msi-parent = <&gic_v2m0>;
+
+ bus-range = <0 0xff>;
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 0xfd020000 0 0xfd020000 0 0x10000
+ /* non-prefetchable memory */
+ 0x82000000 0 0xfc000000 0 0xfc000000 0 0xf00000>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>;
+
+ num-lanes = <1>;
+ clocks = <&cps_syscon0 1 12>;
+ status = "disabled";
+ };
+ };
+};
device_type = "cpu";
reg = <0x0>;
enable-method = "psci";
+ next-level-cache = <&l2>;
cpu-idle-states = <&CPU_SLEEP_0>;
};
device_type = "cpu";
reg = <0x1>;
enable-method = "psci";
+ next-level-cache = <&l2>;
cpu-idle-states = <&CPU_SLEEP_0>;
};
device_type = "cpu";
reg = <0x2>;
enable-method = "psci";
+ next-level-cache = <&l2>;
cpu-idle-states = <&CPU_SLEEP_0>;
};
device_type = "cpu";
reg = <0x3>;
enable-method = "psci";
+ next-level-cache = <&l2>;
cpu-idle-states = <&CPU_SLEEP_0>;
};
+ l2: cache {
+ compatible = "cache";
+ };
+
idle-states {
entry-method = "psci";
CPU_SLEEP_0: cpu-sleep-0 {
};
pmu {
- compatible = "arm,armv8-pmuv3";
+ compatible = "arm,cortex-a53-pmu", "arm,armv8-pmuv3";
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
reg = <0x4000 0x100>;
clocks = <&osc>;
interrupts = <1>;
- status = "disabled";
};
wdt2: watchdog@5000 {
reg = <0x5000 0x100>;
clocks = <&osc>;
interrupts = <2>;
- status = "disabled";
};
sm_gpio0: gpio@8000 {
gpio = <&pio 130 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ connector {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+ type = "d";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi0_out>;
+ };
+ };
+ };
+};
+
+&cec {
+ status = "okay";
+};
+
+&dpi0 {
+ status = "okay";
+};
+
+&hdmi_phy {
+ status = "okay";
+};
+
+&hdmi0 {
+ status = "okay";
+
+ ports {
+ port@1 {
+ reg = <1>;
+
+ hdmi0_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
};
&i2c1 {
<GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+ hdmi_pin: xxx {
+
+ /*hdmi htplg pin*/
+ pins1 {
+ pinmux = <MT8173_PIN_21_HTPLG__FUNC_HTPLG>;
+ input-enable;
+ bias-pull-down;
+ };
+ };
+
i2c0_pins_a: i2c0 {
pins1 {
pinmux = <MT8173_PIN_45_SDA0__FUNC_SDA0>,
clock-names = "spi", "wrap";
};
+ cec: cec@10013000 {
+ compatible = "mediatek,mt8173-cec";
+ reg = <0 0x10013000 0 0xbc>;
+ interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_CEC>;
+ status = "disabled";
+ };
+
vpu: vpu@10020000 {
compatible = "mediatek,mt8173-vpu";
reg = <0 0x10020000 0 0x30000>,
#clock-cells = <1>;
};
+ hdmi_phy: hdmi-phy@10209100 {
+ compatible = "mediatek,mt8173-hdmi-phy";
+ reg = <0 0x10209100 0 0x24>;
+ clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
+ clock-names = "pll_ref";
+ clock-output-names = "hdmitx_dig_cts";
+ mediatek,ibias = <0xa>;
+ mediatek,ibias_up = <0x1c>;
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
mipi_tx0: mipi-dphy@10215000 {
compatible = "mediatek,mt8173-mipi-tx";
reg = <0 0x10215000 0 0x1000>;
status = "disabled";
};
+ hdmiddc0: i2c@11012000 {
+ compatible = "mediatek,mt8173-hdmi-ddc";
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
+ reg = <0 0x11012000 0 0x1C>;
+ clocks = <&pericfg CLK_PERI_I2C5>;
+ clock-names = "ddc-i2c";
+ };
+
i2c6: i2c@11013000 {
compatible = "mediatek,mt8173-i2c";
reg = <0 0x11013000 0 0x70>,
<&apmixedsys CLK_APMIXED_TVDPLL>;
clock-names = "pixel", "engine", "pll";
status = "disabled";
+
+ port {
+ dpi0_out: endpoint {
+ remote-endpoint = <&hdmi0_in>;
+ };
+ };
};
pwm0: pwm@1401e000 {
clocks = <&mmsys CLK_MM_DISP_OD>;
};
+ hdmi0: hdmi@14025000 {
+ compatible = "mediatek,mt8173-hdmi";
+ reg = <0 0x14025000 0 0x400>;
+ interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
+ <&mmsys CLK_MM_HDMI_PLLCK>,
+ <&mmsys CLK_MM_HDMI_AUDIO>,
+ <&mmsys CLK_MM_HDMI_SPDIF>;
+ clock-names = "pixel", "pll", "bclk", "spdif";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_pin>;
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi";
+ mediatek,syscon-hdmi = <&mmsys 0x900>;
+ assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
+ assigned-clock-parents = <&hdmi_phy>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi0_in: endpoint {
+ remote-endpoint = <&dpi0_out>;
+ };
+ };
+ };
+ };
+
larb4: larb@14027000 {
compatible = "mediatek,mt8173-smi-larb";
reg = <0 0x14027000 0 0x1000>;
reg = <0x0 0x80000000 0x0 0xc0000000>;
};
+ host1x@50000000 {
+ dpaux: dpaux@545c0000 {
+ status = "okay";
+ };
+ };
+
pinmux: pinmux@700008d4 {
pinctrl-names = "boot";
pinctrl-0 = <&state_boot>;
};
};
+ i2c@7000d100 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ nau8825@1a {
+ compatible = "nuvoton,nau8825";
+ reg = <0x1a>;
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(E, 6) IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>;
+ clock-names = "mclk";
+
+ nuvoton,jkdet-enable;
+ nuvoton,jkdet-polarity = <GPIO_ACTIVE_LOW>;
+ nuvoton,vref-impedance = <2>;
+ nuvoton,micbias-voltage = <6>;
+ nuvoton,sar-threshold-num = <4>;
+ nuvoton,sar-threshold = <0xc 0x1e 0x38 0x60>;
+ nuvoton,sar-hysteresis = <1>;
+ nuvoton,sar-voltage = <0>;
+ nuvoton,sar-compare-time = <0>;
+ nuvoton,sar-sampling-time = <0>;
+ nuvoton,short-key-debounce = <2>;
+ nuvoton,jack-insert-debounce = <7>;
+ nuvoton,jack-eject-debounce = <7>;
+ status = "okay";
+ };
+
+ audio-codec@2d {
+ compatible = "realtek,rt5677";
+ reg = <0x2d>;
+ interrupt-parent = <&gpio>;
+ interrupts = <TEGRA_GPIO(X, 0) IRQ_TYPE_LEVEL_HIGH>;
+ realtek,reset-gpio = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_LOW>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "okay";
+ };
+ };
+
pmc@7000e400 {
nvidia,invert-interrupt;
nvidia,suspend-mode = <0>;
status = "okay";
};
+ usb@70090000 {
+ phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>,
+ <&{/padctl@7009f000/pads/pcie/lanes/pcie-6}>;
+ phy-names = "usb2-0", "usb3-0";
+
+ dvddio-pex-supply = <&avddio_1v05>;
+ hvddio-pex-supply = <&pp1800>;
+ avdd-usb-supply = <&pp3300>;
+ avdd-pll-utmip-supply = <&pp1800>;
+ avdd-pll-uerefe-supply = <&pp1050_avdd>;
+ dvdd-pex-pll-supply = <&avddio_1v05>;
+ hvdd-pex-pll-e-supply = <&pp1800>;
+
+ status = "okay";
+ };
+
+ padctl@7009f000 {
+ status = "okay";
+
+ pads {
+ usb2 {
+ status = "okay";
+
+ lanes {
+ usb2-0 {
+ nvidia,function = "xusb";
+ status = "okay";
+ };
+ };
+ };
+
+ pcie {
+ status = "okay";
+
+ lanes {
+ pcie-6 {
+ nvidia,function = "usb3-ss";
+ status = "okay";
+ };
+ };
+ };
+ };
+
+ ports {
+ usb2-0 {
+ status = "okay";
+ vbus-supply = <&usbc_vbus>;
+ mode = "otg";
+ };
+
+ usb3-0 {
+ nvidia,usb2-companion = <0>;
+ status = "okay";
+ };
+ };
+ };
+
sdhci@700b0600 {
bus-width = <8>;
non-removable;
status = "okay";
};
+ aconnect@702c0000 {
+ status = "okay";
+
+ dma@702e2000 {
+ status = "okay";
+ };
+
+ agic@702f9000 {
+ status = "okay";
+ };
+ };
+
clocks {
compatible = "simple-bus";
#address-cells = <1>;
};
};
+ max98357a {
+ compatible = "maxim,max98357a";
+ status = "okay";
+ };
+
psci {
compatible = "arm,psci-1.0";
method = "smc";
clock-names = "dpaux", "parent";
resets = <&tegra_car 207>;
reset-names = "dpaux";
+ power-domains = <&pd_sor>;
status = "disabled";
state_dpaux1_aux: pinmux-aux {
clock-names = "dsi", "lp", "parent";
resets = <&tegra_car 48>;
reset-names = "dsi";
+ power-domains = <&pd_sor>;
nvidia,mipi-calibrate = <&mipi 0x0c0>; /* DSIA & DSIB pads */
status = "disabled";
clock-names = "dsi", "lp", "parent";
resets = <&tegra_car 82>;
reset-names = "dsi";
+ power-domains = <&pd_sor>;
nvidia,mipi-calibrate = <&mipi 0x300>; /* DSIC & DSID pads */
status = "disabled";
pinctrl-1 = <&state_dpaux_i2c>;
pinctrl-2 = <&state_dpaux_off>;
pinctrl-names = "aux", "i2c", "off";
+ power-domains = <&pd_sor>;
status = "disabled";
};
pinctrl-1 = <&state_dpaux1_i2c>;
pinctrl-2 = <&state_dpaux1_off>;
pinctrl-names = "aux", "i2c", "off";
+ power-domains = <&pd_sor>;
status = "disabled";
};
clock-names = "dpaux", "parent";
resets = <&tegra_car 181>;
reset-names = "dpaux";
+ power-domains = <&pd_sor>;
status = "disabled";
state_dpaux_aux: pinmux-aux {
};
gpio: gpio@6000d000 {
- compatible = "nvidia,tegra210-gpio", "nvidia,tegra124-gpio", "nvidia,tegra30-gpio";
+ compatible = "nvidia,tegra210-gpio", "nvidia,tegra30-gpio";
reg = <0x0 0x6000d000 0x0 0x1000>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
#power-domain-cells = <0>;
};
+ pd_sor: sor {
+ clocks = <&tegra_car TEGRA210_CLK_SOR0>,
+ <&tegra_car TEGRA210_CLK_SOR1>,
+ <&tegra_car TEGRA210_CLK_CSI>,
+ <&tegra_car TEGRA210_CLK_DSIA>,
+ <&tegra_car TEGRA210_CLK_DSIB>,
+ <&tegra_car TEGRA210_CLK_DPAUX>,
+ <&tegra_car TEGRA210_CLK_DPAUX1>,
+ <&tegra_car TEGRA210_CLK_MIPI_CAL>;
+ resets = <&tegra_car TEGRA210_CLK_SOR0>,
+ <&tegra_car TEGRA210_CLK_SOR1>,
+ <&tegra_car TEGRA210_CLK_CSI>,
+ <&tegra_car TEGRA210_CLK_DSIA>,
+ <&tegra_car TEGRA210_CLK_DSIB>,
+ <&tegra_car TEGRA210_CLK_DPAUX>,
+ <&tegra_car TEGRA210_CLK_DPAUX1>,
+ <&tegra_car TEGRA210_CLK_MIPI_CAL>;
+ #power-domain-cells = <0>;
+ };
+
pd_xusbss: xusba {
clocks = <&tegra_car TEGRA210_CLK_XUSB_SS>;
- clock-names = "xusb-ss";
resets = <&tegra_car TEGRA210_CLK_XUSB_SS>;
- reset-names = "xusb-ss";
#power-domain-cells = <0>;
};
pd_xusbdev: xusbb {
clocks = <&tegra_car TEGRA210_CLK_XUSB_DEV>;
- clock-names = "xusb-dev";
resets = <&tegra_car 95>;
- reset-names = "xusb-dev";
#power-domain-cells = <0>;
};
pd_xusbhost: xusbc {
clocks = <&tegra_car TEGRA210_CLK_XUSB_HOST>;
- clock-names = "xusb-host";
resets = <&tegra_car TEGRA210_CLK_XUSB_HOST>;
- reset-names = "xusb-host";
#power-domain-cells = <0>;
};
};
reg = <0x0 0x700e3000 0x0 0x100>;
clocks = <&tegra_car TEGRA210_CLK_MIPI_CAL>;
clock-names = "mipi-cal";
+ power-domains = <&pd_sor>;
#nvidia,mipi-calibrate-cells = <1>;
};
#size-cells = <1>;
ranges = <0x702c0000 0x0 0x702c0000 0x00040000>;
status = "disabled";
+
+ adma: dma@702e2000 {
+ compatible = "nvidia,tegra210-adma";
+ reg = <0x702e2000 0x2000>;
+ interrupt-parent = <&agic>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ clocks = <&tegra_car TEGRA210_CLK_D_AUDIO>;
+ clock-names = "d_audio";
+ status = "disabled";
+ };
+
+ agic: agic@702f9000 {
+ compatible = "nvidia,tegra210-agic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x702f9000 0x2000>,
+ <0x702fa000 0x2000>;
+ interrupts = <GIC_SPI 102 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ clocks = <&tegra_car TEGRA210_CLK_APE>;
+ clock-names = "clk";
+ status = "disabled";
+ };
};
spi@70410000 {
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb msm8916-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
bias-pull-up;
};
};
+
+ adv7533_int_active: adv533_int_active {
+ pinmux {
+ function = "gpio";
+ pins = "gpio31";
+ };
+ pinconf {
+ pins = "gpio31";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ adv7533_int_suspend: adv7533_int_suspend {
+ pinmux {
+ function = "gpio";
+ pins = "gpio31";
+ };
+ pinconf {
+ pins = "gpio31";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ adv7533_switch_active: adv7533_switch_active {
+ pinmux {
+ function = "gpio";
+ pins = "gpio32";
+ };
+ pinconf {
+ pins = "gpio32";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ adv7533_switch_suspend: adv7533_switch_suspend {
+ pinmux {
+ function = "gpio";
+ pins = "gpio32";
+ };
+ pinconf {
+ pins = "gpio32";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
};
/* On High speed expansion */
label = "HS-I2C2";
status = "okay";
+
+ adv_bridge: bridge@39 {
+ status = "okay";
+
+ compatible = "adi,adv7533";
+ reg = <0x39>;
+
+ interrupt-parent = <&msmgpio>;
+ interrupts = <31 2>;
+
+ adi,dsi-lanes = <4>;
+
+ pd-gpios = <&msmgpio 32 0>;
+
+ avdd-supply = <&pm8916_l6>;
+ v1p2-supply = <&pm8916_l6>;
+ v3p3-supply = <&pm8916_l17>;
+
+ pinctrl-names = "default","sleep";
+ pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+ pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ adv7533_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ adv7533_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
};
i2c@78ba000 {
lpass@07708000 {
status = "okay";
};
+
+ mdss@1a00000 {
+ status = "okay";
+
+ mdp@1a01000 {
+ status = "okay";
+ };
+
+ dsi@1a98000 {
+ status = "okay";
+
+ vdda-supply = <&pm8916_l2>;
+ vddio-supply = <&pm8916_l6>;
+
+ ports {
+ port@1 {
+ endpoint {
+ remote-endpoint = <&adv7533_in>;
+ data-lanes = <0 1 2 3>;
+ };
+ };
+ };
+ };
+
+ dsi-phy@1a98300 {
+ status = "okay";
+
+ vddio-supply = <&pm8916_l6>;
+ };
+ };
};
usb2513 {
pinctrl-names = "default";
pinctrl-0 = <&usb_id_default>;
};
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7533_out>;
+ };
+ };
+ };
};
&smd_rpm_regulators {
--- /dev/null
+/*
+ * Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+&msmgpio {
+ sdc2_cd_on: sdc2_cd_on {
+ mux {
+ pins = "gpio38";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio38";
+ bias-pull-up; /* pull up */
+ drive-strength = <16>; /* 16 MA */
+ };
+ };
+
+ sdc2_cd_off: sdc2_cd_off {
+ mux {
+ pins = "gpio38";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio38";
+ bias-pull-up; /* pull up */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+};
--- /dev/null
+/*
+ * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include "apq8096-db820c.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. DB820c";
+ compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc";
+};
--- /dev/null
+/*
+ * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include "msm8996.dtsi"
+#include "apq8096-db820c-pins.dtsi"
+
+/ {
+ aliases {
+ serial0 = &blsp2_uart1;
+ serial1 = &blsp2_uart2;
+ i2c0 = &blsp1_i2c2;
+ i2c1 = &blsp2_i2c1;
+ i2c2 = &blsp2_i2c0;
+ spi0 = &blsp1_spi0;
+ spi1 = &blsp2_spi5;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ serial@75b0000 {
+ label = "LS-UART1";
+ status = "okay";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_uart1_2pins_default>;
+ pinctrl-1 = <&blsp2_uart1_2pins_sleep>;
+ };
+
+ serial@75b1000 {
+ label = "LS-UART0";
+ status = "okay";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_uart2_4pins_default>;
+ pinctrl-1 = <&blsp2_uart2_4pins_sleep>;
+ };
+
+ i2c@07577000 {
+ /* On Low speed expansion */
+ label = "LS-I2C0";
+ status = "okay";
+ };
+
+ i2c@075b6000 {
+ /* On Low speed expansion */
+ label = "LS-I2C1";
+ status = "okay";
+ };
+
+ spi@07575000 {
+ /* On Low speed expansion */
+ label = "LS-SPI0";
+ status = "okay";
+ };
+
+ i2c@075b5000 {
+ /* On High speed expansion */
+ label = "HS-I2C2";
+ status = "okay";
+ };
+
+ spi@075ba000{
+ /* On High speed expansion */
+ label = "HS-SPI1";
+ status = "okay";
+ };
+
+ sdhci@74a4900 {
+ /* External SD card */
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+ cd-gpios = <&msmgpio 38 0x1>;
+ status = "okay";
+ };
+ };
+};
reg = <0x0 0x89300000 0x0 0x600000>;
no-map;
};
+
+ mba_mem: mba@8ea00000 {
+ no-map;
+ reg = <0 0x8ea00000 0 0x100000>;
+ };
};
cpus {
interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>;
};
+ thermal-zones {
+ cpu-thermal0 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 4>;
+
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit0: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal1 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 3>;
+
+ trips {
+ cpu_alert1: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit1: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
};
firmware {
- scm {
+ scm: scm {
compatible = "qcom,scm";
clocks = <&gcc GCC_CRYPTO_CLK>, <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>;
clock-names = "core", "bus", "iface";
+ #reset-cells = <1>;
};
};
reg = <0x1905000 0x20000>;
};
+ tcsr: syscon@1937000 {
+ compatible = "qcom,tcsr-msm8916", "syscon";
+ reg = <0x1937000 0x30000>;
+ };
+
tcsr_mutex: hwlock {
compatible = "qcom,tcsr-mutex";
syscon = <&tcsr_mutex_regs 0 0x1000>;
compatible = "qcom,ci-hdrc";
reg = <0x78d9000 0x400>;
dr_mode = "peripheral";
- interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
usb-phy = <&usb_otg>;
status = "disabled";
};
usb_host: ehci@78d9000 {
compatible = "qcom,ehci-host";
reg = <0x78d9000 0x400>;
- interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
usb-phy = <&usb_otg>;
status = "disabled";
};
usb_otg: phy@78d9000 {
compatible = "qcom,usb-otg-snps";
reg = <0x78d9000 0x400>;
- interrupts = <GIC_SPI 134 IRQ_TYPE_EDGE_BOTH>,
- <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
qcom,vdd-levels = <500000 1000000 1320000>;
qcom,phy-init-sequence = <0x44 0x6B 0x24 0x13>;
<0x200a000 0x002100>;
reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
interrupt-names = "periph_irq";
- interrupts = <GIC_SPI 190 IRQ_TYPE_NONE>;
+ interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
qcom,ee = <0>;
qcom,channel = <0>;
#address-cells = <2>;
clocks = <&gcc GCC_PRNG_AHB_CLK>;
clock-names = "core";
};
+
+ qfprom: qfprom@5c000 {
+ compatible = "qcom,qfprom";
+ reg = <0x5c000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ tsens_caldata: caldata@d0 {
+ reg = <0xd0 0x8>;
+ };
+ tsens_calsel: calsel@ec {
+ reg = <0xec 0x4>;
+ };
+ };
+
+ tsens: thermal-sensor@4a8000 {
+ compatible = "qcom,msm8916-tsens";
+ reg = <0x4a8000 0x2000>;
+ nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
+ nvmem-cell-names = "calib", "calib_sel";
+ #thermal-sensor-cells = <1>;
+ };
+
+ mdss: mdss@1a00000 {
+ compatible = "qcom,mdss";
+ reg = <0x1a00000 0x1000>,
+ <0x1ac8000 0x3000>;
+ reg-names = "mdss_phys", "vbif_phys";
+
+ power-domains = <&gcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>;
+ clock-names = "iface_clk",
+ "bus_clk",
+ "vsync_clk";
+
+ interrupts = <0 72 0>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mdp: mdp@1a01000 {
+ compatible = "qcom,mdp5";
+ reg = <0x1a01000 0x90000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0 0>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>;
+ clock-names = "iface_clk",
+ "bus_clk",
+ "core_clk",
+ "vsync_clk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: dsi@1a98000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0x1a98000 0x25c>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4 0>;
+
+ assigned-clocks = <&gcc BYTE0_CLK_SRC>,
+ <&gcc PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&dsi_phy0 0>,
+ <&dsi_phy0 1>;
+
+ clocks = <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_BYTE0_CLK>,
+ <&gcc GCC_MDSS_PCLK0_CLK>,
+ <&gcc GCC_MDSS_ESC0_CLK>;
+ clock-names = "mdp_core_clk",
+ "iface_clk",
+ "bus_clk",
+ "byte_clk",
+ "pixel_clk",
+ "core_clk";
+ phys = <&dsi_phy0>;
+ phy-names = "dsi-phy";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp5_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy0: dsi-phy@1a98300 {
+ compatible = "qcom,dsi-phy-28nm-lp";
+ reg = <0x1a98300 0xd4>,
+ <0x1a98500 0x280>,
+ <0x1a98780 0x30>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ #clock-cells = <1>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>;
+ clock-names = "iface_clk";
+ };
+ };
};
smd {
};
};
};
+
+ hexagon-smp2p {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupts = <0 27 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 14>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ hexagon_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ hexagon_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ wcnss-smp2p {
+ compatible = "qcom,smp2p";
+ qcom,smem = <451>, <431>;
+
+ interrupts = <0 143 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 18>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <4>;
+
+ wcnss_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ wcnss_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smsm {
+ compatible = "qcom,smsm";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ qcom,ipc-1 = <&apcs 0 13>;
+ qcom,ipc-6 = <&apcs 0 19>;
+
+ apps_smsm: apps@0 {
+ reg = <0>;
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ hexagon_smsm: hexagon@1 {
+ reg = <1>;
+ interrupts = <0 26 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wcnss_smsm: wcnss@6 {
+ reg = <6>;
+ interrupts = <0 144 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
};
#include "msm8916-pins.dtsi"
};
};
+ thermal-zones {
+ cpu-thermal0 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 3>;
+
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit0: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal1 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 5>;
+
+ trips {
+ cpu_alert1: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit1: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal2 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 8>;
+
+ trips {
+ cpu_alert2: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit2: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal3 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens0 10>;
+
+ trips {
+ cpu_alert3: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu_crit3: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
status = "disabled";
};
+ tsens0: thermal-sensor@4a8000 {
+ compatible = "qcom,msm8996-tsens";
+ reg = <0x4a8000 0x2000>;
+ #thermal-sensor-cells = <1>;
+ };
+
blsp2_uart1: serial@75b0000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x75b0000 0x1000>;
<0x400a000 0x002100>;
reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
interrupt-names = "periph_irq";
- interrupts = <GIC_SPI 326 IRQ_TYPE_NONE>;
+ interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
qcom,ee = <0>;
qcom,channel = <0>;
#address-cells = <2>;
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
--- /dev/null
+/*
+ * Copyright (c) 2016 Matthias Brugger <mbrugger@suse.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "rk3368.dtsi"
+
+/ {
+ model = "Rockchip Orion R68";
+ compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ pinctrl-0 = <&emmc_reset>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ };
+
+ keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_key>;
+
+ power {
+ wakeup-source;
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ label = "GPIO Power";
+ linux,code = <KEY_POWER>;
+ };
+ };
+
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+
+ red {
+ gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+ label = "orion:red:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_ctl>;
+ default-state = "on";
+ };
+
+ blue {
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ label = "orion:blue:led";
+ pinctrl-names = "default";
+ pinctrl-0 = <&stby_pwren>;
+ default-state = "off";
+ };
+ };
+
+ vcc_18: vcc18-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ /* supplies both host and otg */
+ vcc_host: vcc-host-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host_vbus_drv>;
+ regulator-name = "vcc_host";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_io: vcc-io-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_lan: vcc-lan-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_lan";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_sd: vcc-sd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sd";
+ gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_sys: vcc-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vccio_sd: vcc-io-sd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name= "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vccio_wl: vccio-wl-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vccio_wl";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vdd_10: vdd-10-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ disable-wp;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ mmc-hs200-1_2v;
+ mmc-hs200-1_8v;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ snps,reset-gpio = <&gpio3 12 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "ok";
+};
+
+&i2c0 {
+ status = "okay";
+
+ vdd_cpu: syr827@40 {
+ compatible = "silergy,syr827";
+ reg = <0x40>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu";
+ regulator-enable-ramp-delay = <300>;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1500000>;
+ regulator-ramp-delay = <8000>;
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ hym8563: hym8563@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "xin32k";
+ /* rtc_int is not connected */
+ };
+};
+
+&pinctrl {
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ bias-disable;
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ emmc {
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
+ <1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+ };
+
+ emmc-clk {
+ rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ };
+
+ emmc-cmd {
+ rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
+ };
+
+ emmc_reset: emmc-reset {
+ rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ keys {
+ pwr_key: pwr-key {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ leds {
+ stby_pwren: stby-pwren {
+ rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ led_ctl: led-ctl {
+ rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_cd: sdmmc-cd {
+ rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_bus1: sdmmc-bus1 {
+ rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+ };
+
+ usb {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&vcc_18>;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ clock-frequency = <50000000>;
+ clock-freq-min-max = <400000 50000000>;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ keep-power-in-suspend;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vccio_sd>;
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_xfer>;
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
&sdio0 {
assigned-clocks = <&cru SCLK_SDIO0>;
assigned-clock-parents = <&cru PLL_CPLL>;
- broken-cd;
bus-width = <4>;
cap-sd-highspeed;
cap-sdio-irq;
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,boot-mode.h>
#include <dt-bindings/thermal/thermal.h>
/ {
compatible = "rockchip,rk3368-pmu-io-voltage-domain";
status = "disabled";
};
+
+ reboot-mode {
+ compatible = "syscon-reboot-mode";
+ offset = <0x200>;
+ mode-normal = <BOOT_NORMAL>;
+ mode-recovery = <BOOT_RECOVERY>;
+ mode-bootloader = <BOOT_FASTBOOT>;
+ mode-loader = <BOOT_BL_DOWNLOAD>;
+ };
};
cru: clock-controller@ff760000 {
compatible = "rockchip,rk3399-evb", "rockchip,rk3399",
"google,rk3399evb-rev2";
+ clkin_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "clkin_gmac";
+ #clock-cells = <0>;
+ };
+
vdd_center: vdd-center {
compatible = "pwm-regulator";
pwms = <&pwm3 0 25000 0>;
regulator-max-microvolt = <3300000>;
};
+ vcc5v0_sys: vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_host_en>;
+ regulator-name = "vcc5v0_host";
+ vin-supply = <&vcc5v0_sys>;
+ };
+
vcc_phy: vcc-phy-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc_phy";
regulator-always-on;
regulator-boot-on;
};
+
+ vcc_phy: vcc-phy-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_phy";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
};
&emmc_phy {
status = "okay";
};
+&gmac {
+ assigned-clocks = <&cru SCLK_RMII_SRC>;
+ assigned-clock-parents = <&clkin_gmac>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_phy>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ snps,reset-gpio = <&gpio3 15 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ tx_delay = <0x28>;
+ rx_delay = <0x11>;
+ status = "okay";
+};
+
&pwm0 {
status = "okay";
};
status = "okay";
};
+&pcie_phy {
+ status = "disabled";
+};
+
+&pcie0 {
+ ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ num-lanes = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreqn>;
+ status = "disabled";
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
&uart2 {
status = "okay";
};
<1 18 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
+
+ usb2 {
+ vcc5v0_host_en: vcc5v0-host-en {
+ rockchip,pins =
+ <4 25 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
};
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/power/rk3399-power.h>
#include <dt-bindings/thermal/thermal.h>
/ {
};
};
+ pmu_a53 {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW &ppi_cluster0>;
+ };
+
+ pmu_a72 {
+ compatible = "arm,cortex-a72-pmu";
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW &ppi_cluster1>;
+ };
+
psci {
compatible = "arm,psci-1.0";
method = "smc";
timer {
compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
- <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>;
};
xin24m: xin24m {
dmac_bus: dma-controller@ff6d0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x0 0xff6d0000 0x0 0x4000>;
- interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <1>;
clocks = <&cru ACLK_DMAC0_PERILP>;
clock-names = "apb_pclk";
dmac_peri: dma-controller@ff6e0000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x0 0xff6e0000 0x0 0x4000>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH 0>;
#dma-cells = <1>;
clocks = <&cru ACLK_DMAC1_PERILP>;
clock-names = "apb_pclk";
};
};
+ gmac: ethernet@fe300000 {
+ compatible = "rockchip,rk3399-gmac";
+ reg = <0x0 0xfe300000 0x0 0x10000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "macirq";
+ clocks = <&cru SCLK_MAC>, <&cru SCLK_MAC_RX>,
+ <&cru SCLK_MAC_TX>, <&cru SCLK_MACREF>,
+ <&cru SCLK_MACREF_OUT>, <&cru ACLK_GMAC>,
+ <&cru PCLK_GMAC>;
+ clock-names = "stmmaceth", "mac_clk_rx",
+ "mac_clk_tx", "clk_mac_ref",
+ "clk_mac_refout", "aclk_mac",
+ "pclk_mac";
+ power-domains = <&power RK3399_PD_GMAC>;
+ resets = <&cru SRST_A_GMAC>;
+ reset-names = "stmmaceth";
+ rockchip,grf = <&grf>;
+ status = "disabled";
+ };
+
sdio0: dwmmc@fe310000 {
compatible = "rockchip,rk3399-dw-mshc",
"rockchip,rk3288-dw-mshc";
reg = <0x0 0xfe310000 0x0 0x4000>;
- interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH 0>;
clock-freq-min-max = <400000 150000000>;
clocks = <&cru HCLK_SDIO>, <&cru SCLK_SDIO>,
<&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>;
compatible = "rockchip,rk3399-dw-mshc",
"rockchip,rk3288-dw-mshc";
reg = <0x0 0xfe320000 0x0 0x4000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH 0>;
clock-freq-min-max = <400000 150000000>;
clocks = <&cru HCLK_SDMMC>, <&cru SCLK_SDMMC>,
<&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>;
sdhci: sdhci@fe330000 {
compatible = "rockchip,rk3399-sdhci-5.1", "arasan,sdhci-5.1";
reg = <0x0 0xfe330000 0x0 0x10000>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH 0>;
arasan,soc-ctl-syscon = <&grf>;
assigned-clocks = <&cru SCLK_EMMC>;
assigned-clock-rates = <200000000>;
status = "disabled";
};
+ pcie0: pcie@f8000000 {
+ compatible = "rockchip,rk3399-pcie";
+ reg = <0x0 0xf8000000 0x0 0x2000000>,
+ <0x0 0xfd000000 0x0 0x1000000>;
+ reg-names = "axi-base", "apb-base";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ bus-range = <0x0 0x1>;
+ clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
+ <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>;
+ clock-names = "aclk", "aclk-perf",
+ "hclk", "pm";
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "sys", "legacy", "client";
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+ <0 0 0 2 &pcie0_intc 1>,
+ <0 0 0 3 &pcie0_intc 2>,
+ <0 0 0 4 &pcie0_intc 3>;
+ msi-map = <0x0 &its 0x0 0x1000>;
+ phys = <&pcie_phy>;
+ phy-names = "pcie-phy";
+ ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000
+ 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>;
+ resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
+ <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>;
+ reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
+ status = "disabled";
+
+ pcie0_intc: interrupt-controller {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+ };
+
usb_host0_ehci: usb@fe380000 {
compatible = "generic-ehci";
reg = <0x0 0xfe380000 0x0 0x20000>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>;
clock-names = "hclk_host0", "hclk_host0_arb";
+ phys = <&u2phy0_host>;
+ phy-names = "usb";
status = "disabled";
};
usb_host0_ohci: usb@fe3a0000 {
compatible = "generic-ohci";
reg = <0x0 0xfe3a0000 0x0 0x20000>;
- interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru HCLK_HOST0>, <&cru HCLK_HOST0_ARB>;
clock-names = "hclk_host0", "hclk_host0_arb";
status = "disabled";
usb_host1_ehci: usb@fe3c0000 {
compatible = "generic-ehci";
reg = <0x0 0xfe3c0000 0x0 0x20000>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>;
clock-names = "hclk_host1", "hclk_host1_arb";
+ phys = <&u2phy1_host>;
+ phy-names = "usb";
status = "disabled";
};
usb_host1_ohci: usb@fe3e0000 {
compatible = "generic-ohci";
reg = <0x0 0xfe3e0000 0x0 0x20000>;
- interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru HCLK_HOST1>, <&cru HCLK_HOST1_ARB>;
clock-names = "hclk_host1", "hclk_host1_arb";
status = "disabled";
gic: interrupt-controller@fee00000 {
compatible = "arm,gic-v3";
- #interrupt-cells = <3>;
+ #interrupt-cells = <4>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
<0x0 0xfff00000 0 0x10000>, /* GICC */
<0x0 0xfff10000 0 0x10000>, /* GICH */
<0x0 0xfff20000 0 0x10000>; /* GICV */
- interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
its: interrupt-controller@fee20000 {
compatible = "arm,gic-v3-its";
msi-controller;
reg = <0x0 0xfee20000 0x0 0x20000>;
};
+
+ ppi-partitions {
+ ppi_cluster0: interrupt-partition-0 {
+ affinity = <&cpu_l0 &cpu_l1 &cpu_l2 &cpu_l3>;
+ };
+
+ ppi_cluster1: interrupt-partition-1 {
+ affinity = <&cpu_b0 &cpu_b1>;
+ };
+ };
+ };
+
+ saradc: saradc@ff100000 {
+ compatible = "rockchip,rk3399-saradc";
+ reg = <0x0 0xff100000 0x0 0x100>;
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH 0>;
+ #io-channel-cells = <1>;
+ clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>;
+ clock-names = "saradc", "apb_pclk";
+ resets = <&cru SRST_P_SARADC>;
+ reset-names = "saradc-apb";
+ status = "disabled";
};
i2c1: i2c@ff110000 {
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C1>, <&cru PCLK_I2C1>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c1_xfer>;
#address-cells = <1>;
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C2>, <&cru PCLK_I2C2>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_xfer>;
#address-cells = <1>;
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C3>, <&cru PCLK_I2C3>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c3_xfer>;
#address-cells = <1>;
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C5>, <&cru PCLK_I2C5>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c5_xfer>;
#address-cells = <1>;
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C6>, <&cru PCLK_I2C6>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c6_xfer>;
#address-cells = <1>;
assigned-clock-rates = <200000000>;
clocks = <&cru SCLK_I2C7>, <&cru PCLK_I2C7>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c7_xfer>;
#address-cells = <1>;
reg = <0x0 0xff180000 0x0 0x100>;
clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
reg = <0x0 0xff190000 0x0 0x100>;
clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
reg = <0x0 0xff1a0000 0x0 0x100>;
clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
reg = <0x0 0xff1b0000 0x0 0x100>;
clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
reg = <0x0 0xff1c0000 0x0 0x1000>;
clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi0_clk &spi0_tx &spi0_rx &spi0_cs0>;
#address-cells = <1>;
reg = <0x0 0xff1d0000 0x0 0x1000>;
clocks = <&cru SCLK_SPI1>, <&cru PCLK_SPI1>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi1_clk &spi1_tx &spi1_rx &spi1_cs0>;
#address-cells = <1>;
reg = <0x0 0xff1e0000 0x0 0x1000>;
clocks = <&cru SCLK_SPI2>, <&cru PCLK_SPI2>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi2_clk &spi2_tx &spi2_rx &spi2_cs0>;
#address-cells = <1>;
reg = <0x0 0xff1f0000 0x0 0x1000>;
clocks = <&cru SCLK_SPI4>, <&cru PCLK_SPI4>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi4_clk &spi4_tx &spi4_rx &spi4_cs0>;
#address-cells = <1>;
reg = <0x0 0xff200000 0x0 0x1000>;
clocks = <&cru SCLK_SPI5>, <&cru PCLK_SPI5>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi5_clk &spi5_tx &spi5_rx &spi5_cs0>;
#address-cells = <1>;
tsadc: tsadc@ff260000 {
compatible = "rockchip,rk3399-tsadc";
reg = <0x0 0xff260000 0x0 0x100>;
- interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH 0>;
assigned-clocks = <&cru SCLK_TSADC>;
assigned-clock-rates = <750000>;
clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>;
status = "disabled";
};
+ qos_gmac: qos@ffa5c000 {
+ compatible = "syscon";
+ reg = <0x0 0xffa5c000 0x0 0x20>;
+ };
+
+ qos_hdcp: qos@ffa90000 {
+ compatible = "syscon";
+ reg = <0x0 0xffa90000 0x0 0x20>;
+ };
+
+ qos_iep: qos@ffa98000 {
+ compatible = "syscon";
+ reg = <0x0 0xffa98000 0x0 0x20>;
+ };
+
+ qos_isp0_m0: qos@ffaa0000 {
+ compatible = "syscon";
+ reg = <0x0 0xffaa0000 0x0 0x20>;
+ };
+
+ qos_isp0_m1: qos@ffaa0080 {
+ compatible = "syscon";
+ reg = <0x0 0xffaa0080 0x0 0x20>;
+ };
+
+ qos_isp1_m0: qos@ffaa8000 {
+ compatible = "syscon";
+ reg = <0x0 0xffaa8000 0x0 0x20>;
+ };
+
+ qos_isp1_m1: qos@ffaa8080 {
+ compatible = "syscon";
+ reg = <0x0 0xffaa8080 0x0 0x20>;
+ };
+
+ qos_rga_r: qos@ffab0000 {
+ compatible = "syscon";
+ reg = <0x0 0xffab0000 0x0 0x20>;
+ };
+
+ qos_rga_w: qos@ffab0080 {
+ compatible = "syscon";
+ reg = <0x0 0xffab0080 0x0 0x20>;
+ };
+
+ qos_video_m0: qos@ffab8000 {
+ compatible = "syscon";
+ reg = <0x0 0xffab8000 0x0 0x20>;
+ };
+
+ qos_video_m1_r: qos@ffac0000 {
+ compatible = "syscon";
+ reg = <0x0 0xffac0000 0x0 0x20>;
+ };
+
+ qos_video_m1_w: qos@ffac0080 {
+ compatible = "syscon";
+ reg = <0x0 0xffac0080 0x0 0x20>;
+ };
+
+ qos_vop_big_r: qos@ffac8000 {
+ compatible = "syscon";
+ reg = <0x0 0xffac8000 0x0 0x20>;
+ };
+
+ qos_vop_big_w: qos@ffac8080 {
+ compatible = "syscon";
+ reg = <0x0 0xffac8080 0x0 0x20>;
+ };
+
+ qos_vop_little: qos@ffad0000 {
+ compatible = "syscon";
+ reg = <0x0 0xffad0000 0x0 0x20>;
+ };
+
+ qos_gpu: qos@ffae0000 {
+ compatible = "syscon";
+ reg = <0x0 0xffae0000 0x0 0x20>;
+ };
+
+ pmu: power-management@ff310000 {
+ compatible = "rockchip,rk3399-pmu", "syscon", "simple-mfd";
+ reg = <0x0 0xff310000 0x0 0x1000>;
+
+ /*
+ * Note: RK3399 supports 6 voltage domains including VD_CORE_L,
+ * VD_CORE_B, VD_CENTER, VD_GPU, VD_LOGIC and VD_PMU.
+ * Some of the power domains are grouped together for every
+ * voltage domain.
+ * The detail contents as below.
+ */
+ power: power-controller {
+ compatible = "rockchip,rk3399-power-controller";
+ #power-domain-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* These power domains are grouped by VD_CENTER */
+ pd_iep@RK3399_PD_IEP {
+ reg = <RK3399_PD_IEP>;
+ clocks = <&cru ACLK_IEP>,
+ <&cru HCLK_IEP>;
+ pm_qos = <&qos_iep>;
+ };
+ pd_rga@RK3399_PD_RGA {
+ reg = <RK3399_PD_RGA>;
+ clocks = <&cru ACLK_RGA>,
+ <&cru HCLK_RGA>;
+ pm_qos = <&qos_rga_r>,
+ <&qos_rga_w>;
+ };
+ pd_vcodec@RK3399_PD_VCODEC {
+ reg = <RK3399_PD_VCODEC>;
+ clocks = <&cru ACLK_VCODEC>,
+ <&cru HCLK_VCODEC>;
+ pm_qos = <&qos_video_m0>;
+ };
+ pd_vdu@RK3399_PD_VDU {
+ reg = <RK3399_PD_VDU>;
+ clocks = <&cru ACLK_VDU>,
+ <&cru HCLK_VDU>;
+ pm_qos = <&qos_video_m1_r>,
+ <&qos_video_m1_w>;
+ };
+
+ /* These power domains are grouped by VD_GPU */
+ pd_gpu@RK3399_PD_GPU {
+ reg = <RK3399_PD_GPU>;
+ clocks = <&cru ACLK_GPU>;
+ pm_qos = <&qos_gpu>;
+ };
+
+ /* These power domains are grouped by VD_LOGIC */
+ pd_gmac@RK3399_PD_GMAC {
+ reg = <RK3399_PD_GMAC>;
+ clocks = <&cru ACLK_GMAC>;
+ pm_qos = <&qos_gmac>;
+ };
+ pd_vio@RK3399_PD_VIO {
+ reg = <RK3399_PD_VIO>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pd_hdcp@RK3399_PD_HDCP {
+ reg = <RK3399_PD_HDCP>;
+ clocks = <&cru ACLK_HDCP>,
+ <&cru HCLK_HDCP>,
+ <&cru PCLK_HDCP>;
+ pm_qos = <&qos_hdcp>;
+ };
+ pd_isp0@RK3399_PD_ISP0 {
+ reg = <RK3399_PD_ISP0>;
+ clocks = <&cru ACLK_ISP0>,
+ <&cru HCLK_ISP0>;
+ pm_qos = <&qos_isp0_m0>,
+ <&qos_isp0_m1>;
+ };
+ pd_isp1@RK3399_PD_ISP1 {
+ reg = <RK3399_PD_ISP1>;
+ clocks = <&cru ACLK_ISP1>,
+ <&cru HCLK_ISP1>;
+ pm_qos = <&qos_isp1_m0>,
+ <&qos_isp1_m1>;
+ };
+ pd_tcpc0@RK3399_PD_TCPC0 {
+ reg = <RK3399_PD_TCPD0>;
+ clocks = <&cru SCLK_UPHY0_TCPDCORE>,
+ <&cru SCLK_UPHY0_TCPDPHY_REF>;
+ };
+ pd_tcpc1@RK3399_PD_TCPC1 {
+ reg = <RK3399_PD_TCPD1>;
+ clocks = <&cru SCLK_UPHY1_TCPDCORE>,
+ <&cru SCLK_UPHY1_TCPDPHY_REF>;
+ };
+ pd_vo@RK3399_PD_VO {
+ reg = <RK3399_PD_VO>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pd_vopb@RK3399_PD_VOPB {
+ reg = <RK3399_PD_VOPB>;
+ clocks = <&cru ACLK_VOP0>,
+ <&cru HCLK_VOP0>;
+ pm_qos = <&qos_vop_big_r>,
+ <&qos_vop_big_w>;
+ };
+ pd_vopl@RK3399_PD_VOPL {
+ reg = <RK3399_PD_VOPL>;
+ clocks = <&cru ACLK_VOP1>,
+ <&cru HCLK_VOP1>;
+ pm_qos = <&qos_vop_little>;
+ };
+ };
+ };
+ };
+ };
+
pmugrf: syscon@ff320000 {
compatible = "rockchip,rk3399-pmugrf", "syscon", "simple-mfd";
reg = <0x0 0xff320000 0x0 0x1000>;
reg = <0x0 0xff350000 0x0 0x1000>;
clocks = <&pmucru SCLK_SPI3_PMU>, <&pmucru PCLK_SPI3_PMU>;
clock-names = "spiclk", "apb_pclk";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&spi3_clk &spi3_tx &spi3_rx &spi3_cs0>;
#address-cells = <1>;
reg = <0x0 0xff370000 0x0 0x100>;
clocks = <&pmucru SCLK_UART4_PMU>, <&pmucru PCLK_UART4_PMU>;
clock-names = "baudclk", "apb_pclk";
- interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH 0>;
reg-shift = <2>;
reg-io-width = <4>;
pinctrl-names = "default";
assigned-clock-rates = <200000000>;
clocks = <&pmucru SCLK_I2C0_PMU>, <&pmucru PCLK_I2C0_PMU>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c0_xfer>;
#address-cells = <1>;
assigned-clock-rates = <200000000>;
clocks = <&pmucru SCLK_I2C4_PMU>, <&pmucru PCLK_I2C4_PMU>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c4_xfer>;
#address-cells = <1>;
assigned-clock-rates = <200000000>;
clocks = <&pmucru SCLK_I2C8_PMU>, <&pmucru PCLK_I2C8_PMU>;
clock-names = "i2c", "pclk";
- interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH 0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c8_xfer>;
#address-cells = <1>;
status = "disabled";
};
+ efuse0: efuse@ff690000 {
+ compatible = "rockchip,rk3399-efuse";
+ reg = <0x0 0xff690000 0x0 0x80>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&cru PCLK_EFUSE1024NS>;
+ clock-names = "pclk_efuse";
+
+ /* Data cells */
+ cpub_leakage: cpu-leakage@17 {
+ reg = <0x17 0x1>;
+ };
+ gpu_leakage: gpu-leakage@18 {
+ reg = <0x18 0x1>;
+ };
+ center_leakage: center-leakage@19 {
+ reg = <0x19 0x1>;
+ };
+ cpul_leakage: cpu-leakage@1a {
+ reg = <0x1a 0x1>;
+ };
+ logic_leakage: logic-leakage@1b {
+ reg = <0x1b 0x1>;
+ };
+ wafer_info: wafer-info@1c {
+ reg = <0x1c 0x1>;
+ };
+ };
+
pmucru: pmu-clock-controller@ff750000 {
compatible = "rockchip,rk3399-pmucru";
reg = <0x0 0xff750000 0x0 0x1000>;
<&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
<&cru PCLK_PERIHP>,
<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
- <&cru PCLK_PERILP0>,
+ <&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>;
assigned-clock-rates =
<594000000>, <800000000>,
<150000000>, <75000000>,
<37500000>,
<100000000>, <100000000>,
- <50000000>,
+ <50000000>, <600000000>,
<100000000>, <50000000>;
};
status = "disabled";
};
+ u2phy0: usb2-phy@e450 {
+ compatible = "rockchip,rk3399-usb2phy";
+ reg = <0xe450 0x10>;
+ clocks = <&cru SCLK_USB2PHY0_REF>;
+ clock-names = "phyclk";
+ #clock-cells = <0>;
+ clock-output-names = "clk_usbphy0_480m";
+ status = "disabled";
+
+ u2phy0_host: host-port {
+ #phy-cells = <0>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "linestate";
+ status = "disabled";
+ };
+ };
+
+ u2phy1: usb2-phy@e460 {
+ compatible = "rockchip,rk3399-usb2phy";
+ reg = <0xe460 0x10>;
+ clocks = <&cru SCLK_USB2PHY1_REF>;
+ clock-names = "phyclk";
+ #clock-cells = <0>;
+ clock-output-names = "clk_usbphy1_480m";
+ status = "disabled";
+
+ u2phy1_host: host-port {
+ #phy-cells = <0>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "linestate";
+ status = "disabled";
+ };
+ };
+
emmc_phy: phy@f780 {
compatible = "rockchip,rk3399-emmc-phy";
reg = <0xf780 0x24>;
#phy-cells = <0>;
status = "disabled";
};
+
+ pcie_phy: pcie-phy {
+ compatible = "rockchip,rk3399-pcie-phy";
+ clocks = <&cru SCLK_PCIEPHY_REF>;
+ clock-names = "refclk";
+ #phy-cells = <0>;
+ resets = <&cru SRST_PCIEPHY>;
+ reset-names = "phy";
+ status = "disabled";
+ };
};
- watchdog@ff840000 {
+ tcphy0: phy@ff7c0000 {
+ compatible = "rockchip,rk3399-typec-phy";
+ reg = <0x0 0xff7c0000 0x0 0x40000>;
+ clocks = <&cru SCLK_UPHY0_TCPDCORE>,
+ <&cru SCLK_UPHY0_TCPDPHY_REF>;
+ clock-names = "tcpdcore", "tcpdphy-ref";
+ assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>;
+ assigned-clock-rates = <50000000>;
+ resets = <&cru SRST_UPHY0>,
+ <&cru SRST_UPHY0_PIPE_L00>,
+ <&cru SRST_P_UPHY0_TCPHY>;
+ reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+ rockchip,grf = <&grf>;
+ rockchip,typec-conn-dir = <0xe580 0 16>;
+ rockchip,usb3tousb2-en = <0xe580 3 19>;
+ rockchip,external-psm = <0xe588 14 30>;
+ rockchip,pipe-status = <0xe5c0 0 0>;
+ status = "disabled";
+
+ tcphy0_dp: dp-port {
+ #phy-cells = <0>;
+ };
+
+ tcphy0_usb3: usb3-port {
+ #phy-cells = <0>;
+ };
+ };
+
+ tcphy1: phy@ff800000 {
+ compatible = "rockchip,rk3399-typec-phy";
+ reg = <0x0 0xff800000 0x0 0x40000>;
+ clocks = <&cru SCLK_UPHY1_TCPDCORE>,
+ <&cru SCLK_UPHY1_TCPDPHY_REF>;
+ clock-names = "tcpdcore", "tcpdphy-ref";
+ assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>;
+ assigned-clock-rates = <50000000>;
+ resets = <&cru SRST_UPHY1>,
+ <&cru SRST_UPHY1_PIPE_L00>,
+ <&cru SRST_P_UPHY1_TCPHY>;
+ reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+ rockchip,grf = <&grf>;
+ rockchip,typec-conn-dir = <0xe58c 0 16>;
+ rockchip,usb3tousb2-en = <0xe58c 3 19>;
+ rockchip,external-psm = <0xe594 14 30>;
+ rockchip,pipe-status = <0xe5c0 16 16>;
+ status = "disabled";
+
+ tcphy1_dp: dp-port {
+ #phy-cells = <0>;
+ };
+
+ tcphy1_usb3: usb3-port {
+ #phy-cells = <0>;
+ };
+ };
+
+ watchdog@ff848000 {
compatible = "snps,dw-wdt";
- reg = <0x0 0xff840000 0x0 0x100>;
+ reg = <0x0 0xff848000 0x0 0x100>;
clocks = <&cru PCLK_WDT>;
- interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH 0>;
};
rktimer: rktimer@ff850000 {
compatible = "rockchip,rk3399-timer";
reg = <0x0 0xff850000 0x0 0x1000>;
- interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH 0>;
clocks = <&cru PCLK_TIMER0>, <&cru SCLK_TIMER00>;
clock-names = "pclk", "timer";
};
spdif: spdif@ff870000 {
compatible = "rockchip,rk3399-spdif";
reg = <0x0 0xff870000 0x0 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dmac_bus 7>;
dma-names = "tx";
clock-names = "mclk", "hclk";
compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s";
reg = <0x0 0xff880000 0x0 0x1000>;
rockchip,grf = <&grf>;
- interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dmac_bus 0>, <&dmac_bus 1>;
dma-names = "tx", "rx";
clock-names = "i2s_clk", "i2s_hclk";
i2s1: i2s@ff890000 {
compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s";
reg = <0x0 0xff890000 0x0 0x1000>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dmac_bus 2>, <&dmac_bus 3>;
dma-names = "tx", "rx";
clock-names = "i2s_clk", "i2s_hclk";
i2s2: i2s@ff8a0000 {
compatible = "rockchip,rk3399-i2s", "rockchip,rk3066-i2s";
reg = <0x0 0xff8a0000 0x0 0x1000>;
- interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH 0>;
dmas = <&dmac_bus 4>, <&dmac_bus 5>;
dma-names = "tx", "rx";
clock-names = "i2s_clk", "i2s_hclk";
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff720000 0x0 0x100>;
clocks = <&pmucru PCLK_GPIO0_PMU>;
- interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff730000 0x0 0x100>;
clocks = <&pmucru PCLK_GPIO1_PMU>;
- interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff780000 0x0 0x100>;
clocks = <&cru PCLK_GPIO2>;
- interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff788000 0x0 0x100>;
clocks = <&cru PCLK_GPIO3>;
- interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
compatible = "rockchip,gpio-bank";
reg = <0x0 0xff790000 0x0 0x100>;
clocks = <&cru PCLK_GPIO4>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
gpio-controller;
#gpio-cells = <0x2>;
drive-strength = <13>;
};
+ clock {
+ clk_32k: clk-32k {
+ rockchip,pins = <0 0 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+
+ gmac {
+ rgmii_pins: rgmii-pins {
+ rockchip,pins =
+ /* mac_txclk */
+ <3 17 RK_FUNC_1 &pcfg_pull_none_13ma>,
+ /* mac_rxclk */
+ <3 14 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_mdio */
+ <3 13 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_txen */
+ <3 12 RK_FUNC_1 &pcfg_pull_none_13ma>,
+ /* mac_clk */
+ <3 11 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_rxdv */
+ <3 9 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_mdc */
+ <3 8 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_rxd1 */
+ <3 7 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_rxd0 */
+ <3 6 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_txd1 */
+ <3 5 RK_FUNC_1 &pcfg_pull_none_13ma>,
+ /* mac_txd0 */
+ <3 4 RK_FUNC_1 &pcfg_pull_none_13ma>,
+ /* mac_rxd3 */
+ <3 3 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_rxd2 */
+ <3 2 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_txd3 */
+ <3 1 RK_FUNC_1 &pcfg_pull_none_13ma>,
+ /* mac_txd2 */
+ <3 0 RK_FUNC_1 &pcfg_pull_none_13ma>;
+ };
+
+ rmii_pins: rmii-pins {
+ rockchip,pins =
+ /* mac_mdio */
+ <3 13 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_txen */
+ <3 12 RK_FUNC_1 &pcfg_pull_none_13ma>,
+ /* mac_clk */
+ <3 11 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_rxer */
+ <3 10 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_rxdv */
+ <3 9 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_mdc */
+ <3 8 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_rxd1 */
+ <3 7 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_rxd0 */
+ <3 6 RK_FUNC_1 &pcfg_pull_none>,
+ /* mac_txd1 */
+ <3 5 RK_FUNC_1 &pcfg_pull_none_13ma>,
+ /* mac_txd0 */
+ <3 4 RK_FUNC_1 &pcfg_pull_none_13ma>;
+ };
+ };
+
i2c0 {
i2c0_xfer: i2c0-xfer {
rockchip,pins =
<1 14 RK_FUNC_1 &pcfg_pull_none>;
};
};
+
+ pcie {
+ pcie_clkreqn: pci-clkreqn {
+ rockchip,pins =
+ <2 26 RK_FUNC_2 &pcfg_pull_none>;
+ };
+
+ pcie_clkreqnb: pci-clkreqnb {
+ rockchip,pins =
+ <4 24 RK_FUNC_1 &pcfg_pull_none>;
+ };
+ };
+
};
};
-dtb-$(CONFIG_ARCH_UNIPHIER) += uniphier-ph1-ld20-ref.dtb
+dtb-$(CONFIG_ARCH_UNIPHIER) += \
+ uniphier-ld11-ref.dtb \
+ uniphier-ld20-ref.dtb
always := $(dtb-y)
clean-files := *.dtb
--- /dev/null
+/*
+ * Device Tree Source for UniPhier LD11 Reference Board
+ *
+ * Copyright (C) 2016 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "uniphier-ld11.dtsi"
+/include/ "uniphier-ref-daughter.dtsi"
+/include/ "uniphier-support-card.dtsi"
+
+/ {
+ model = "UniPhier LD11 Reference Board";
+ compatible = "socionext,uniphier-ld11-ref", "socionext,uniphier-ld11";
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x80000000 0 0x40000000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ i2c5 = &i2c5;
+ };
+};
+
+ðsc {
+ interrupts = <0 48 4>;
+};
+
+&serial0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Device Tree Source for UniPhier LD11 SoC
+ *
+ * Copyright (C) 2016 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/memreserve/ 0x80000000 0x00000008; /* cpu-release-addr */
+
+/ {
+ compatible = "socionext,uniphier-ld11";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0 0x000>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0 0x80000000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0 0x001>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0 0x80000000>;
+ };
+ };
+
+ clocks {
+ refclk: ref {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <1 13 4>,
+ <1 14 4>,
+ <1 11 4>,
+ <1 10 4>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+
+ serial0: serial@54006800 {
+ compatible = "socionext,uniphier-uart";
+ status = "disabled";
+ reg = <0x54006800 0x40>;
+ interrupts = <0 33 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+ clocks = <&peri_clk 0>;
+ };
+
+ serial1: serial@54006900 {
+ compatible = "socionext,uniphier-uart";
+ status = "disabled";
+ reg = <0x54006900 0x40>;
+ interrupts = <0 35 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ clocks = <&peri_clk 1>;
+ };
+
+ serial2: serial@54006a00 {
+ compatible = "socionext,uniphier-uart";
+ status = "disabled";
+ reg = <0x54006a00 0x40>;
+ interrupts = <0 37 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ clocks = <&peri_clk 2>;
+ };
+
+ serial3: serial@54006b00 {
+ compatible = "socionext,uniphier-uart";
+ status = "disabled";
+ reg = <0x54006b00 0x40>;
+ interrupts = <0 177 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ clocks = <&peri_clk 3>;
+ };
+
+ i2c0: i2c@58780000 {
+ compatible = "socionext,uniphier-fi2c";
+ status = "disabled";
+ reg = <0x58780000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 41 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ clocks = <&peri_clk 4>;
+ clock-frequency = <100000>;
+ };
+
+ i2c1: i2c@58781000 {
+ compatible = "socionext,uniphier-fi2c";
+ status = "disabled";
+ reg = <0x58781000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 42 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clocks = <&peri_clk 5>;
+ clock-frequency = <100000>;
+ };
+
+ i2c2: i2c@58782000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x58782000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 43 4>;
+ clocks = <&peri_clk 6>;
+ clock-frequency = <400000>;
+ };
+
+ i2c3: i2c@58783000 {
+ compatible = "socionext,uniphier-fi2c";
+ status = "disabled";
+ reg = <0x58783000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 44 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clocks = <&peri_clk 7>;
+ clock-frequency = <100000>;
+ };
+
+ i2c4: i2c@58784000 {
+ compatible = "socionext,uniphier-fi2c";
+ status = "disabled";
+ reg = <0x58784000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 45 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ clocks = <&peri_clk 8>;
+ clock-frequency = <100000>;
+ };
+
+ i2c5: i2c@58785000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x58785000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 25 4>;
+ clocks = <&peri_clk 9>;
+ clock-frequency = <400000>;
+ };
+
+ system_bus: system-bus@58c00000 {
+ compatible = "socionext,uniphier-system-bus";
+ status = "disabled";
+ reg = <0x58c00000 0x400>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_system_bus>;
+ };
+
+ smpctrl@59800000 {
+ compatible = "socionext,uniphier-smpctrl";
+ reg = <0x59801000 0x400>;
+ };
+
+ perictrl@59820000 {
+ compatible = "socionext,uniphier-perictrl",
+ "simple-mfd", "syscon";
+ reg = <0x59820000 0x200>;
+
+ peri_clk: clock {
+ compatible = "socionext,uniphier-ld11-peri-clock";
+ #clock-cells = <1>;
+ };
+
+ peri_rst: reset {
+ compatible = "socionext,uniphier-ld11-peri-reset";
+ #reset-cells = <1>;
+ };
+ };
+
+ usb0: usb@5a800100 {
+ compatible = "socionext,uniphier-ehci", "generic-ehci";
+ status = "disabled";
+ reg = <0x5a800100 0x100>;
+ interrupts = <0 243 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0>;
+ clocks = <&mio_clk 7>, <&mio_clk 8>, <&mio_clk 12>;
+ resets = <&mio_rst 7>, <&mio_rst 8>, <&mio_rst 12>, <&sys_rst 8>;
+ };
+
+ usb1: usb@5a810100 {
+ compatible = "socionext,uniphier-ehci", "generic-ehci";
+ status = "disabled";
+ reg = <0x5a810100 0x100>;
+ interrupts = <0 244 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb1>;
+ clocks = <&mio_clk 7>, <&mio_clk 9>, <&mio_clk 13>;
+ resets = <&mio_rst 7>, <&mio_rst 9>, <&mio_rst 13>, <&sys_rst 8>;
+ };
+
+ usb2: usb@5a820100 {
+ compatible = "socionext,uniphier-ehci", "generic-ehci";
+ status = "disabled";
+ reg = <0x5a820100 0x100>;
+ interrupts = <0 245 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb2>;
+ clocks = <&mio_clk 7>, <&mio_clk 10>, <&mio_clk 14>;
+ resets = <&mio_rst 7>, <&mio_rst 10>, <&mio_rst 14>, <&sys_rst 8>;
+ };
+
+ mioctrl@5b3e0000 {
+ compatible = "socionext,uniphier-mioctrl",
+ "simple-mfd", "syscon";
+ reg = <0x5b3e0000 0x800>;
+
+ mio_clk: clock {
+ compatible = "socionext,uniphier-ld11-mio-clock";
+ #clock-cells = <1>;
+ };
+
+ mio_rst: reset {
+ compatible = "socionext,uniphier-ld11-mio-reset";
+ #reset-cells = <1>;
+ resets = <&sys_rst 7>;
+ };
+ };
+
+ soc-glue@5f800000 {
+ compatible = "socionext,uniphier-soc-glue",
+ "simple-mfd", "syscon";
+ reg = <0x5f800000 0x2000>;
+
+ pinctrl: pinctrl {
+ compatible = "socionext,uniphier-ld11-pinctrl";
+ };
+ };
+
+ gic: interrupt-controller@5fe00000 {
+ compatible = "arm,gic-v3";
+ reg = <0x5fe00000 0x10000>, /* GICD */
+ <0x5fe40000 0x80000>; /* GICR */
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <1 9 4>;
+ };
+
+ sysctrl@61840000 {
+ compatible = "socionext,uniphier-ld11-sysctrl",
+ "simple-mfd", "syscon";
+ reg = <0x61840000 0x4000>;
+
+ sys_clk: clock {
+ compatible = "socionext,uniphier-ld11-clock";
+ #clock-cells = <1>;
+ };
+
+ sys_rst: reset {
+ compatible = "socionext,uniphier-ld11-reset";
+ #reset-cells = <1>;
+ };
+ };
+ };
+};
+
+/include/ "uniphier-pinctrl.dtsi"
--- /dev/null
+/*
+ * Device Tree Source for UniPhier LD20 Reference Board
+ *
+ * Copyright (C) 2015-2016 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+/include/ "uniphier-ld20.dtsi"
+/include/ "uniphier-ref-daughter.dtsi"
+/include/ "uniphier-support-card.dtsi"
+
+/ {
+ model = "UniPhier LD20 Reference Board";
+ compatible = "socionext,uniphier-ld20-ref", "socionext,uniphier-ld20";
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x80000000 0 0xc0000000>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ serial0 = &serial0;
+ serial1 = &serial1;
+ serial2 = &serial2;
+ serial3 = &serial3;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ i2c5 = &i2c5;
+ };
+};
+
+ðsc {
+ interrupts = <0 48 4>;
+};
+
+&serial0 {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Device Tree Source for UniPhier LD20 SoC
+ *
+ * Copyright (C) 2015-2016 Socionext Inc.
+ * Author: Masahiro Yamada <yamada.masahiro@socionext.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/memreserve/ 0x80000000 0x00000008; /* cpu-release-addr */
+
+/ {
+ compatible = "socionext,uniphier-ld20";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu2>;
+ };
+ core1 {
+ cpu = <&cpu3>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72", "arm,armv8";
+ reg = <0 0x000>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0 0x80000000>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a72", "arm,armv8";
+ reg = <0 0x001>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0 0x80000000>;
+ };
+
+ cpu2: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0 0x100>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0 0x80000000>;
+ };
+
+ cpu3: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0 0x101>;
+ enable-method = "spin-table";
+ cpu-release-addr = <0 0x80000000>;
+ };
+ };
+
+ clocks {
+ refclk: ref {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <1 13 4>,
+ <1 14 4>,
+ <1 11 4>,
+ <1 10 4>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+
+ serial0: serial@54006800 {
+ compatible = "socionext,uniphier-uart";
+ status = "disabled";
+ reg = <0x54006800 0x40>;
+ interrupts = <0 33 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart0>;
+ clocks = <&peri_clk 0>;
+ };
+
+ serial1: serial@54006900 {
+ compatible = "socionext,uniphier-uart";
+ status = "disabled";
+ reg = <0x54006900 0x40>;
+ interrupts = <0 35 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ clocks = <&peri_clk 1>;
+ };
+
+ serial2: serial@54006a00 {
+ compatible = "socionext,uniphier-uart";
+ status = "disabled";
+ reg = <0x54006a00 0x40>;
+ interrupts = <0 37 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ clocks = <&peri_clk 2>;
+ };
+
+ serial3: serial@54006b00 {
+ compatible = "socionext,uniphier-uart";
+ status = "disabled";
+ reg = <0x54006b00 0x40>;
+ interrupts = <0 177 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ clocks = <&peri_clk 3>;
+ };
+
+ i2c0: i2c@58780000 {
+ compatible = "socionext,uniphier-fi2c";
+ status = "disabled";
+ reg = <0x58780000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 41 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c0>;
+ clocks = <&peri_clk 4>;
+ clock-frequency = <100000>;
+ };
+
+ i2c1: i2c@58781000 {
+ compatible = "socionext,uniphier-fi2c";
+ status = "disabled";
+ reg = <0x58781000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 42 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clocks = <&peri_clk 5>;
+ clock-frequency = <100000>;
+ };
+
+ i2c2: i2c@58782000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x58782000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 43 4>;
+ clocks = <&peri_clk 6>;
+ clock-frequency = <400000>;
+ };
+
+ i2c3: i2c@58783000 {
+ compatible = "socionext,uniphier-fi2c";
+ status = "disabled";
+ reg = <0x58783000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 44 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clocks = <&peri_clk 7>;
+ clock-frequency = <100000>;
+ };
+
+ i2c4: i2c@58784000 {
+ compatible = "socionext,uniphier-fi2c";
+ status = "disabled";
+ reg = <0x58784000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 45 4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ clocks = <&peri_clk 8>;
+ clock-frequency = <100000>;
+ };
+
+ i2c5: i2c@58785000 {
+ compatible = "socionext,uniphier-fi2c";
+ reg = <0x58785000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <0 25 4>;
+ clocks = <&peri_clk 9>;
+ clock-frequency = <400000>;
+ };
+
+ system_bus: system-bus@58c00000 {
+ compatible = "socionext,uniphier-system-bus";
+ status = "disabled";
+ reg = <0x58c00000 0x400>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_system_bus>;
+ };
+
+ smpctrl@59800000 {
+ compatible = "socionext,uniphier-smpctrl";
+ reg = <0x59801000 0x400>;
+ };
+
+ mioctrl@59810000 {
+ compatible = "socionext,uniphier-mioctrl",
+ "simple-mfd", "syscon";
+ reg = <0x59810000 0x800>;
+
+ mio_clk: clock {
+ compatible = "socionext,uniphier-ld20-mio-clock";
+ #clock-cells = <1>;
+ };
+
+ mio_rst: reset {
+ compatible = "socionext,uniphier-ld20-mio-reset";
+ #reset-cells = <1>;
+ };
+ };
+
+ perictrl@59820000 {
+ compatible = "socionext,uniphier-perictrl",
+ "simple-mfd", "syscon";
+ reg = <0x59820000 0x200>;
+
+ peri_clk: clock {
+ compatible = "socionext,uniphier-ld20-peri-clock";
+ #clock-cells = <1>;
+ };
+
+ peri_rst: reset {
+ compatible = "socionext,uniphier-ld20-peri-reset";
+ #reset-cells = <1>;
+ };
+ };
+
+ soc-glue@5f800000 {
+ compatible = "socionext,uniphier-soc-glue",
+ "simple-mfd", "syscon";
+ reg = <0x5f800000 0x2000>;
+
+ pinctrl: pinctrl {
+ compatible = "socionext,uniphier-ld20-pinctrl";
+ };
+ };
+
+ gic: interrupt-controller@5fe00000 {
+ compatible = "arm,gic-v3";
+ reg = <0x5fe00000 0x10000>, /* GICD */
+ <0x5fe80000 0x80000>; /* GICR */
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <1 9 4>;
+ };
+
+ sysctrl@61840000 {
+ compatible = "socionext,uniphier-sysctrl",
+ "simple-mfd", "syscon";
+ reg = <0x61840000 0x4000>;
+
+ sys_clk: clock {
+ compatible = "socionext,uniphier-ld20-clock";
+ #clock-cells = <1>;
+ };
+
+ sys_rst: reset {
+ compatible = "socionext,uniphier-ld20-reset";
+ #reset-cells = <1>;
+ };
+ };
+ };
+};
+
+/include/ "uniphier-pinctrl.dtsi"
+++ /dev/null
-/*
- * Device Tree Source for UniPhier PH1-LD20 Reference Board
- *
- * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-/include/ "uniphier-ph1-ld20.dtsi"
-/include/ "uniphier-ref-daughter.dtsi"
-/include/ "uniphier-support-card.dtsi"
-
-/ {
- model = "UniPhier PH1-LD20 Reference Board";
- compatible = "socionext,ph1-ld20-ref", "socionext,ph1-ld20";
-
- memory {
- device_type = "memory";
- reg = <0 0x80000000 0 0xc0000000>;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- aliases {
- serial0 = &serial0;
- serial1 = &serial1;
- serial2 = &serial2;
- serial3 = &serial3;
- i2c0 = &i2c0;
- i2c1 = &i2c1;
- i2c2 = &i2c2;
- i2c3 = &i2c3;
- i2c4 = &i2c4;
- i2c5 = &i2c5;
- };
-};
-
-ðsc {
- interrupts = <0 48 4>;
-};
-
-&serial0 {
- status = "okay";
-};
-
-&i2c0 {
- status = "okay";
-};
+++ /dev/null
-/*
- * Device Tree Source for UniPhier PH1-LD20 SoC
- *
- * Copyright (C) 2015 Masahiro Yamada <yamada.masahiro@socionext.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/memreserve/ 0x80000000 0x00000008; /* cpu-release-addr */
-
-/ {
- compatible = "socionext,ph1-ld20";
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&gic>;
-
- cpus {
- #address-cells = <2>;
- #size-cells = <0>;
-
- cpu-map {
- cluster0 {
- core0 {
- cpu = <&cpu0>;
- };
- core1 {
- cpu = <&cpu1>;
- };
- };
-
- cluster1 {
- core0 {
- cpu = <&cpu2>;
- };
- core1 {
- cpu = <&cpu3>;
- };
- };
- };
-
- cpu0: cpu@0 {
- device_type = "cpu";
- compatible = "arm,cortex-a72", "arm,armv8";
- reg = <0 0x000>;
- enable-method = "spin-table";
- cpu-release-addr = <0 0x80000000>;
- };
-
- cpu1: cpu@1 {
- device_type = "cpu";
- compatible = "arm,cortex-a72", "arm,armv8";
- reg = <0 0x001>;
- enable-method = "spin-table";
- cpu-release-addr = <0 0x80000000>;
- };
-
- cpu2: cpu@100 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0 0x100>;
- enable-method = "spin-table";
- cpu-release-addr = <0 0x80000000>;
- };
-
- cpu3: cpu@101 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0 0x101>;
- enable-method = "spin-table";
- cpu-release-addr = <0 0x80000000>;
- };
- };
-
- clocks {
- refclk: ref {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <25000000>;
- };
-
- uart_clk: uart_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <58820000>;
- };
-
- i2c_clk: i2c_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <50000000>;
- };
- };
-
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <1 13 4>,
- <1 14 4>,
- <1 11 4>,
- <1 10 4>;
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0 0 0xffffffff>;
-
- serial0: serial@54006800 {
- compatible = "socionext,uniphier-uart";
- status = "disabled";
- reg = <0x54006800 0x40>;
- interrupts = <0 33 4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart0>;
- clocks = <&uart_clk>;
- };
-
- serial1: serial@54006900 {
- compatible = "socionext,uniphier-uart";
- status = "disabled";
- reg = <0x54006900 0x40>;
- interrupts = <0 35 4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- clocks = <&uart_clk>;
- };
-
- serial2: serial@54006a00 {
- compatible = "socionext,uniphier-uart";
- status = "disabled";
- reg = <0x54006a00 0x40>;
- interrupts = <0 37 4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- clocks = <&uart_clk>;
- };
-
- serial3: serial@54006b00 {
- compatible = "socionext,uniphier-uart";
- status = "disabled";
- reg = <0x54006b00 0x40>;
- interrupts = <0 177 4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- clocks = <&uart_clk>;
- };
-
- i2c0: i2c@58780000 {
- compatible = "socionext,uniphier-fi2c";
- status = "disabled";
- reg = <0x58780000 0x80>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0 41 4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c0>;
- clocks = <&i2c_clk>;
- clock-frequency = <100000>;
- };
-
- i2c1: i2c@58781000 {
- compatible = "socionext,uniphier-fi2c";
- status = "disabled";
- reg = <0x58781000 0x80>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0 42 4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- clocks = <&i2c_clk>;
- clock-frequency = <100000>;
- };
-
- i2c2: i2c@58782000 {
- compatible = "socionext,uniphier-fi2c";
- reg = <0x58782000 0x80>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0 43 4>;
- clocks = <&i2c_clk>;
- clock-frequency = <400000>;
- };
-
- i2c3: i2c@58783000 {
- compatible = "socionext,uniphier-fi2c";
- status = "disabled";
- reg = <0x58783000 0x80>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0 44 4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c3>;
- clocks = <&i2c_clk>;
- clock-frequency = <100000>;
- };
-
- i2c4: i2c@58784000 {
- compatible = "socionext,uniphier-fi2c";
- status = "disabled";
- reg = <0x58784000 0x80>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0 45 4>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c4>;
- clocks = <&i2c_clk>;
- clock-frequency = <100000>;
- };
-
- i2c5: i2c@58785000 {
- compatible = "socionext,uniphier-fi2c";
- reg = <0x58785000 0x80>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <0 25 4>;
- clocks = <&i2c_clk>;
- clock-frequency = <400000>;
- };
-
- system_bus: system-bus@58c00000 {
- compatible = "socionext,uniphier-system-bus";
- status = "disabled";
- reg = <0x58c00000 0x400>;
- #address-cells = <2>;
- #size-cells = <1>;
- };
-
- smpctrl@59800000 {
- compatible = "socionext,uniphier-smpctrl";
- reg = <0x59801000 0x400>;
- };
-
- soc-glue@5f800000 {
- compatible = "simple-mfd", "syscon";
- reg = <0x5f800000 0x2000>;
-
- pinctrl: pinctrl {
- compatible = "socionext,uniphier-ld20-pinctrl";
- };
- };
-
- gic: interrupt-controller@5fe00000 {
- compatible = "arm,gic-v3";
- reg = <0x5fe00000 0x10000>, /* GICD */
- <0x5fe80000 0x80000>; /* GICR */
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <1 9 4>;
- };
- };
-};
-
-/include/ "uniphier-pinctrl.dtsi"
memory {
device_type = "memory";
- reg = <0x0 0x0 0x40000000>;
+ reg = <0x0 0x0 0x0 0x40000000>;
};
};
/ {
compatible = "xlnx,zynqmp";
#address-cells = <2>;
- #size-cells = <1>;
+ #size-cells = <2>;
cpus {
#address-cells = <1>;
pmu {
compatible = "arm,armv8-pmuv3";
+ interrupt-parent = <&gic>;
interrupts = <0 143 4>,
<0 144 4>,
<0 145 4>,
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <1>;
- ranges;
+ ranges = <0 0 0 0 0xffffffff>;
gic: interrupt-controller@f9010000 {
compatible = "arm,gic-400", "arm,cortex-a15-gic";
#interrupt-cells = <3>;
reg = <0x0 0xf9010000 0x10000>,
- <0x0 0xf902f000 0x2000>,
+ <0x0 0xf9020000 0x20000>,
<0x0 0xf9040000 0x20000>,
- <0x0 0xf906f000 0x2000>;
+ <0x0 0xf9060000 0x20000>;
interrupt-controller;
interrupt-parent = <&gic>;
interrupts = <1 9 0xf04>;
amba: amba {
compatible = "simple-bus";
#address-cells = <2>;
- #size-cells = <1>;
+ #size-cells = <2>;
ranges;
can0: can@ff060000 {
compatible = "xlnx,zynq-can-1.0";
status = "disabled";
clock-names = "can_clk", "pclk";
- reg = <0x0 0xff060000 0x1000>;
+ reg = <0x0 0xff060000 0x0 0x1000>;
interrupts = <0 23 4>;
interrupt-parent = <&gic>;
tx-fifo-depth = <0x40>;
compatible = "xlnx,zynq-can-1.0";
status = "disabled";
clock-names = "can_clk", "pclk";
- reg = <0x0 0xff070000 0x1000>;
+ reg = <0x0 0xff070000 0x0 0x1000>;
interrupts = <0 24 4>;
interrupt-parent = <&gic>;
tx-fifo-depth = <0x40>;
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 57 4>, <0 57 4>;
- reg = <0x0 0xff0b0000 0x1000>;
+ reg = <0x0 0xff0b0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 59 4>, <0 59 4>;
- reg = <0x0 0xff0c0000 0x1000>;
+ reg = <0x0 0xff0c0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 61 4>, <0 61 4>;
- reg = <0x0 0xff0d0000 0x1000>;
+ reg = <0x0 0xff0d0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 63 4>, <0 63 4>;
- reg = <0x0 0xff0e0000 0x1000>;
+ reg = <0x0 0xff0e0000 0x0 0x1000>;
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <1>;
#size-cells = <0>;
interrupts = <0 16 4>;
interrupt-controller;
#interrupt-cells = <2>;
- reg = <0x0 0xff0a0000 0x1000>;
+ reg = <0x0 0xff0a0000 0x0 0x1000>;
};
i2c0: i2c@ff020000 {
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 17 4>;
- reg = <0x0 0xff020000 0x1000>;
+ reg = <0x0 0xff020000 0x0 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 18 4>;
- reg = <0x0 0xff030000 0x1000>;
+ reg = <0x0 0xff030000 0x0 0x1000>;
#address-cells = <1>;
#size-cells = <0>;
};
+ pcie: pcie@fd0e0000 {
+ compatible = "xlnx,nwl-pcie-2.11";
+ status = "disabled";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ msi-controller;
+ device_type = "pci";
+ interrupt-parent = <&gic>;
+ interrupts = <0 118 4>,
+ <0 117 4>,
+ <0 116 4>,
+ <0 115 4>, /* MSI_1 [63...32] */
+ <0 114 4>; /* MSI_0 [31...0] */
+ interrupt-names = "misc", "dummy", "intx",
+ "msi1", "msi0";
+ msi-parent = <&pcie>;
+ reg = <0x0 0xfd0e0000 0x0 0x1000>,
+ <0x0 0xfd480000 0x0 0x1000>,
+ <0x80 0x00000000 0x0 0x1000000>;
+ reg-names = "breg", "pcireg", "cfg";
+ ranges = <0x02000000 0x00000000 0xe0000000 0x00000000
+ 0xe0000000 0x00000000 0x10000000
+ /* non-prefetchable memory */
+ 0x43000000 0x00000006 0x00000000 0x00000006
+ 0x00000000 0x00000002 0x00000000>;
+ /* prefetchable memory */
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc 0x1>,
+ <0x0 0x0 0x0 0x2 &pcie_intc 0x2>,
+ <0x0 0x0 0x0 0x3 &pcie_intc 0x3>,
+ <0x0 0x0 0x0 0x4 &pcie_intc 0x4>;
+ pcie_intc: legacy-interrupt-controller {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+ };
+
sata: ahci@fd0c0000 {
compatible = "ceva,ahci-1v84";
status = "disabled";
- reg = <0x0 0xfd0c0000 0x2000>;
+ reg = <0x0 0xfd0c0000 0x0 0x2000>;
interrupt-parent = <&gic>;
interrupts = <0 133 4>;
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 48 4>;
- reg = <0x0 0xff160000 0x1000>;
+ reg = <0x0 0xff160000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 49 4>;
- reg = <0x0 0xff170000 0x1000>;
+ reg = <0x0 0xff170000 0x0 0x1000>;
clock-names = "clk_xin", "clk_ahb";
};
smmu: smmu@fd800000 {
compatible = "arm,mmu-500";
- reg = <0x0 0xfd800000 0x20000>;
+ reg = <0x0 0xfd800000 0x0 0x20000>;
#global-interrupts = <1>;
interrupt-parent = <&gic>;
interrupts = <0 157 4>,
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 19 4>;
- reg = <0x0 0xff040000 0x1000>;
+ reg = <0x0 0xff040000 0x0 0x1000>;
clock-names = "ref_clk", "pclk";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 20 4>;
- reg = <0x0 0xff050000 0x1000>;
+ reg = <0x0 0xff050000 0x0 0x1000>;
clock-names = "ref_clk", "pclk";
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 36 4>, <0 37 4>, <0 38 4>;
- reg = <0x0 0xff110000 0x1000>;
+ reg = <0x0 0xff110000 0x0 0x1000>;
timer-width = <32>;
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 39 4>, <0 40 4>, <0 41 4>;
- reg = <0x0 0xff120000 0x1000>;
+ reg = <0x0 0xff120000 0x0 0x1000>;
timer-width = <32>;
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 42 4>, <0 43 4>, <0 44 4>;
- reg = <0x0 0xff130000 0x1000>;
+ reg = <0x0 0xff130000 0x0 0x1000>;
timer-width = <32>;
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 45 4>, <0 46 4>, <0 47 4>;
- reg = <0x0 0xff140000 0x1000>;
+ reg = <0x0 0xff140000 0x0 0x1000>;
timer-width = <32>;
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 21 4>;
- reg = <0x0 0xff000000 0x1000>;
+ reg = <0x0 0xff000000 0x0 0x1000>;
clock-names = "uart_clk", "pclk";
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 22 4>;
- reg = <0x0 0xff010000 0x1000>;
+ reg = <0x0 0xff010000 0x0 0x1000>;
clock-names = "uart_clk", "pclk";
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 65 4>;
- reg = <0x0 0xfe200000 0x40000>;
+ reg = <0x0 0xfe200000 0x0 0x40000>;
clock-names = "clk_xin", "clk_ahb";
};
status = "disabled";
interrupt-parent = <&gic>;
interrupts = <0 70 4>;
- reg = <0x0 0xfe300000 0x40000>;
+ reg = <0x0 0xfe300000 0x0 0x40000>;
clock-names = "clk_xin", "clk_ahb";
};
compatible = "cdns,wdt-r1p2";
status = "disabled";
interrupt-parent = <&gic>;
- interrupts = <0 52 1>;
- reg = <0x0 0xfd4d0000 0x1000>;
+ interrupts = <0 113 1>;
+ reg = <0x0 0xfd4d0000 0x0 0x1000>;
timeout-sec = <10>;
};
};
--- /dev/null
+dtb-$(CONFIG_ARCH_ZX) += zx296718-evb.dtb
+
+always := $(dtb-y)
+subdir-y := $(dts-dirs)
+clean-files := *.dtb
--- /dev/null
+/*
+ * Copyright 2016 ZTE Corporation.
+ * Copyright 2016 Linaro Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "zx296718.dtsi"
+
+/ {
+ model = "ZTE zx296718 evaluation board";
+ compatible = "zte,zx296718-evb", "zte,zx296718";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x40000000>;
+ };
+
+};
+
+&uart0 {
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2016 ZTE Corporation.
+ * Copyright 2016 Linaro Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ compatible = "zte,zx296718";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&gic>;
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ core2 {
+ cpu = <&cpu2>;
+ };
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53","arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53","arm,armv8";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53","arm,armv8";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53","arm,armv8";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ clk24k: clk-24k {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000>;
+ clock-output-names = "rtcclk";
+ };
+
+ osc32k: clk-osc32k {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32000>;
+ clock-output-names = "osc32k";
+ };
+
+ osc12m: clk-osc12m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <12000000>;
+ clock-output-names = "osc12m";
+ };
+
+ osc24m: clk-osc24m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24m";
+ };
+
+ osc25m: clk-osc25m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ clock-output-names = "osc25m";
+ };
+
+ osc60m: clk-osc60m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <60000000>;
+ clock-output-names = "osc60m";
+ };
+
+ osc99m: clk-osc99m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <99000000>;
+ clock-output-names = "osc99m";
+ };
+
+ osc125m: clk-osc125m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "osc125m";
+ };
+
+ osc198m: clk-osc198m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <198000000>;
+ clock-output-names = "osc198m";
+ };
+
+ pll_audio: clk-pll-884m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <884000000>;
+ clock-output-names = "pll_audio";
+ };
+
+ pll_ddr: clk-pll-932m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <932000000>;
+ clock-output-names = "pll_ddr";
+ };
+
+ pll_hsic: clk-pll-960m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <960000000>;
+ clock-output-names = "pll_hsic";
+ };
+
+ pll_mac: clk-pll-1000m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1000000000>;
+ clock-output-names = "pll_mac";
+ };
+
+ pll_vga: clk-pll-1073m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1073000000>;
+ clock-output-names = "pll_vga";
+ };
+
+ pll_mm0: clk-pll-1188m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1188000000>;
+ clock-output-names = "pll_mm0";
+ };
+
+ pll_mm1: clk-pll-1296m {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1296000000>;
+ clock-output-names = "pll_mm1";
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gic: interrupt-controller@2a00000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ #redistributor-regions = <6>;
+ redistributor-stride = <0x0 0x40000>;
+ interrupt-controller;
+ reg = <0x02a00000 0x10000>,
+ <0x02b00000 0x20000>,
+ <0x02b20000 0x20000>,
+ <0x02b40000 0x20000>,
+ <0x02b60000 0x20000>,
+ <0x02b80000 0x20000>,
+ <0x02ba0000 0x20000>;
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges;
+
+ aon_sysctrl: aon-sysctrl@116000 {
+ compatible = "zte,zx296718-aon-sysctrl", "syscon";
+ reg = <0x116000 0x1000>;
+ };
+
+ uart0: uart@11f000 {
+ compatible = "arm,pl011", "arm,primecell";
+ arm,primecell-periphid = <0x001feffe>;
+ reg = <0x11f000 0x1000>;
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24m>;
+ clock-names = "apb_pclk";
+ status = "disabled";
+ };
+
+ dma: dma-controller@1460000 {
+ compatible = "zte,zx296702-dma";
+ reg = <0x01460000 0x1000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24m>;
+ clock-names = "dmaclk";
+ #dma-cells = <1>;
+ dma-channels = <32>;
+ dma-requests = <32>;
+ };
+
+ sysctrl: sysctrl@1463000 {
+ compatible = "zte,zx296718-sysctrl", "syscon";
+ reg = <0x1463000 0x1000>;
+ };
+ };
+};
projects / cascardo / linux.git / commitdiff