git.cascardo.info Git - cascardo/linux.git/log

charger: tps65090: Allow charger module to be used when no irq

On the ARM Chromebook tps65090 has two masters: the AP (the main
processor running linux) and the EC (the embedded controller).  The AP
is allowed to mess with FETs but the EC is in charge of charge control.

The tps65090 interupt line is routed to both the AP and the EC, which
can cause quite a headache.  Having two people adjusting masks and
acking interrupts is a recipe for disaster.

In the shipping kernel we had a hack to have the AP pay attention to
the IRQ but not to ack it.  It also wasn't supposed to configure the
IRQ in any way.  That hack allowed us to detect when the device was
charging without messing with the EC's state.

The current tps65090 infrastructure makes the above difficult, and it
was a bit of a hack to begin with.  Rather than uglify the driver to
support it, just extend the driver's existing notion of "no irq" to
the charger.  This makes the charger code poll every 2 seconds for AC
detect, which is sufficient.

For proper functioning, requires (mfd: tps65090: Don't tell child
devices we have an IRQ if we don't).  If we don't have that patch
we'll simply fail to probe on devices without an interrupt (just like
we did before this patch).

Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[sre@kernel.org: Use -ENXIO instead of NO_IRQ for missing interrupt,
since NO_IRQ is not available on all architectures.]
Signed-off-by: Sebastian Reichel <sre@kernel.org>

power/reset: Fix GPL v2 license string typo

Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

power: poweroff: gpio: convert to use descriptors

This switches the GPIO poweroff driver to use GPIO descriptors
rather than numeral GPIOs. We get rid of the specific inversion
handling as GPIO descriptors know if they are active low or
high and can assert the line properly, so we do not need to
check the flag OF_GPIO_ACTIVE_LOW returned from the old call
of_get_gpio_flags() anymore.

Also convert to use managed resources and use dev_* message
printing while we're at it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

bq27000: report missing device better.

One an hdq buss, a missing device reads as 0xff, not -1.
So do a translation to allow detecting of a missing bus.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

bq27x00_battery: Introduce the use of the managed version of kzalloc

This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions for both platform and i2c drivers. Also, the unecessary
variable ret and labels batt_failed3, err_free were removed.

The following Coccinele script was used for making the change:

@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
  .probe = probefn,
  .remove = removefn,
};

@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
  <+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
  ...
?-kfree(e);
  ...+>
}

@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
  <...
- kfree(e);
  ...>
}

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Documentation: DT: Document rx51-battery binding

Add devicetree binding documentation for rx51-battery,
which is a simple A/D converter consumer.

Signed-off-by: Sebastian Reichel <sre@kernel.org>

rx51_battery: convert to iio consumer

Update rx51-battery driver to use the new IIO API of
twl4030-madc and add DT support.

Signed-off-by: Sebastian Reichel <sre@kernel.org>

bq2415x_charger: Fix Atomic Sleep Bug

Move sysfs_notify and i2c_transfer calls from bq2415x_notifier_call
to bq2415x_timer_work to avoid sleeping in atomic context.

This fixes the following bug:

[ 7.667449] Workqueue: events power_supply_changed_work
[ 7.673034] [<c0015c28>] (unwind_backtrace+0x0/0xe0) from [<c0011e1c>] (show_stack+0x10/0x14)
[ 7.682098] [<c0011e1c>] (show_stack+0x10/0x14) from [<c052cdd0>] (dump_stack+0x78/0xac)
[ 7.690704] [<c052cdd0>] (dump_stack+0x78/0xac) from [<c052a044>] (__schedule_bug+0x48/0x60)
[ 7.699645] [<c052a044>] (__schedule_bug+0x48/0x60) from [<c053071c>] (__schedule+0x74/0x638)
[ 7.708618] [<c053071c>] (__schedule+0x74/0x638) from [<c05301fc>] (schedule_timeout+0x1dc/0x24c)
[ 7.718017] [<c05301fc>] (schedule_timeout+0x1dc/0x24c) from [<c05316ec>] (wait_for_common+0x138/0x17c)
[ 7.727966] [<c05316ec>] (wait_for_common+0x138/0x17c) from [<c0362a70>] (omap_i2c_xfer+0x340/0x4a0)
[ 7.737640] [<c0362a70>] (omap_i2c_xfer+0x340/0x4a0) from [<c035d928>] (__i2c_transfer+0x40/0x74)
[ 7.747039] [<c035d928>] (__i2c_transfer+0x40/0x74) from [<c035e22c>] (i2c_transfer+0x6c/0x90)
[ 7.756195] [<c035e22c>] (i2c_transfer+0x6c/0x90) from [<c037ad24>] (bq2415x_i2c_write+0x48/0x78)
[ 7.765563] [<c037ad24>] (bq2415x_i2c_write+0x48/0x78) from [<c037ae60>] (bq2415x_set_weak_battery_voltage+0x4c/0x50)
[ 7.776824] [<c037ae60>] (bq2415x_set_weak_battery_voltage+0x4c/0x50) from [<c037bce8>] (bq2415x_set_mode+0xdc/0x14c)
[ 7.788085] [<c037bce8>] (bq2415x_set_mode+0xdc/0x14c) from [<c037bfb8>] (bq2415x_notifier_call+0xa8/0xb4)
[ 7.798309] [<c037bfb8>] (bq2415x_notifier_call+0xa8/0xb4) from [<c005f228>] (notifier_call_chain+0x38/0x68)
[ 7.808715] [<c005f228>] (notifier_call_chain+0x38/0x68) from [<c005f284>] (__atomic_notifier_call_chain+0x2c/0x3c)
[ 7.819732] [<c005f284>] (__atomic_notifier_call_chain+0x2c/0x3c) from [<c005f2a8>] (atomic_notifier_call_chain+0x14/0x18)
[ 7.831420] [<c005f2a8>] (atomic_notifier_call_chain+0x14/0x18) from [<c0378078>] (power_supply_changed_work+0x6c/0xb8)
[ 7.842864] [<c0378078>] (power_supply_changed_work+0x6c/0xb8) from [<c00556c0>] (process_one_work+0x248/0x440)
[ 7.853546] [<c00556c0>] (process_one_work+0x248/0x440) from [<c0055d6c>] (worker_thread+0x208/0x350)
[ 7.863372] [<c0055d6c>] (worker_thread+0x208/0x350) from [<c005b0ac>] (kthread+0xc8/0xdc)
[ 7.872131] [<c005b0ac>] (kthread+0xc8/0xdc) from [<c000e138>] (ret_from_fork+0x14/0x3c)

Fixes: 32260308b4ca ("bq2415x_charger: Use power_supply notifier for automode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>

Merge tag 'gfs2-fixes' of git://git./linux/kernel/git/steve/gfs2-3.0-fixes

Pull gfs2 fixes from Steven Whitehouse:
"This patch set contains two minor docs/spelling fixes, some fixes for
  flock, a change to use GFP_NOFS to avoid recursion on a rarely used
  code path and a fix for a race relating to the glock lru"

* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
  GFS2: memcontrol: Spelling s/invlidate/invalidate/
  GFS2: Allow caching of glocks for flock
  GFS2: Allow flocks to use normal glock dq rather than dq_wait
  GFS2: replace count*size kzalloc by kcalloc
  GFS2: Use GFP_NOFS when allocating glocks
  GFS2: Fix race in glock lru glock disposal
  GFS2: Only wait for demote when last holder is dequeued

Merge tag 'dm-3.16-fixes-2' of git://git./linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:
"Fix the dm-thinp and dm-cache targets to disallow changing the data
  device's block size"

* tag 'dm-3.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm cache metadata: do not allow the data block size to change
  dm thin metadata: do not allow the data block size to change

Merge tag 'upstream-3.16-rc6' of git://git.infradead.org/linux-ubifs

Pull UBI fixes from Artem Bityutskiy:
"Two UBI fastmap-related fixes for v3.16:

   - fix UBI fastmap support which we broke in 3.16-rc1 by reversing the
     volumes RB-tree sorting criteria.
   - make sure that we scrub all PEBs where we see bit-flips - we were
     missing some of them when the fastmap feature was enabled"

* tag 'upstream-3.16-rc6' of git://git.infradead.org/linux-ubifs:
  UBI: fastmap: do not miss bit-flips
  UBI: fix the volumes tree sorting criteria

Merge tag 'xfs-for-linus-3.16-rc5' of git://oss.sgi.com/xfs/xfs

Pull xfs fixes from Dave Chinner:
"Fixes for low memory perforamnce regressions and a quota inode
  handling regression.

  These are regression fixes for issues recently introduced - the change
  in the stack switch location is fairly important, so I've held off
  sending this update until I was sure that it still addresses the stack
  usage problem the original solved.  So while the commits in the xfs
  tree are recent, it has been under tested for several weeks now"

* tag 'xfs-for-linus-3.16-rc5' of git://oss.sgi.com/xfs/xfs:
  xfs: null unused quota inodes when quota is on
  xfs: refine the allocation stack switch
  Revert "xfs: block allocation work needs to be kswapd aware"

GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes

Cc: cluster-devel@redhat.com
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

GFS2: memcontrol: Spelling s/invlidate/invalidate/

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: cluster-devel@redhat.com
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

GFS2: Allow caching of glocks for flock

This patch removes the GLF_NOCACHE flag from the glocks associated with
flocks. There should be no good reason not to cache glocks for flocks:
they only force the glock to be demoted before they can be reacquired,
which can slow down performance and even cause glock hangs, especially
in cases where the flocks are held in Shared (SH) mode.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

GFS2: Allow flocks to use normal glock dq rather than dq_wait

This patch allows flock glocks to use a non-blocking dequeue rather
than dq_wait. It also reverts the previous patch I had posted regarding
dq_wait. The reverted patch isn't necessarily a bad idea, but I decided
this might avoid unforeseen side effects, and was therefore safer.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

GFS2: replace count*size kzalloc by kcalloc

kcalloc manages count*sizeof overflow.

Cc: cluster-devel@redhat.com
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

GFS2: Use GFP_NOFS when allocating glocks

Normally GFP_KERNEL is ok here, but there is now a rarely used code path
relating to deallocation of unlinked inodes (in certain corner cases)
which if hit at times of memory shortage can cause recursion while
trying to free memory.

One solution would be to try and move the gfs2_glock_get() call so
that it is no longer called while another glock is held, but that
doesn't look at all easy, so GFP_NOFS is the best solution for the
time being.

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

GFS2: Fix race in glock lru glock disposal

We must not leave items on the LRU list with GLF_LOCK set, since
they can be removed if the glock is brought back into use, which
may then potentially result in a hang, waiting for GLF_LOCK to
clear.

It doesn't happen very often, since it requires a glock that has
not been used for a long time to be brought back into use at the
same moment that the shrinker is part way through disposing of
glocks.

The fix is to set GLF_LOCK at a later time, when we already know
that the other locks can be obtained. Also, we now only release
the lru_lock in case a resched is needed, rather than on every
iteration.

Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

GFS2: Only wait for demote when last holder is dequeued

Function gfs2_glock_dq_wait is supposed to dequeue a glock and then
wait for the lock to be demoted. The problem is, if this is a shared
lock, its demote will depend on the other holders, which means you
might end up waiting forever because the other process is blocked.
This problem is especially apparent when dealing with nested flocks.

Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

Merge tag 'stable/for-linus-3.16-rc5-tag' of git://git./linux/kernel/git/xen/tip

Pull Xen fixes from Konrad Rzeszutek Wilk:
"Two fixes found during migration of PV guests.  David would be the one
  doing this pull but he is on vacation.

  Fixes:
   - fix console deadlock when resuming PV guests
   - fix regression hit when ballooning and resuming PV guests"

* tag 'stable/for-linus-3.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: set ballooned out pages as invalid in p2m
  xen/manage: fix potential deadlock when resuming the console

Merge tag 'trace-fixes-v3.16-rc5-v2' of git://git./linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
"A few more fixes for ftrace infrastructure.

  I was cleaning out my INBOX and found two fixes from zhangwei from a
  year ago that were lost in my mail.  These fix an inconsistency
  between trace_puts() and the way trace_printk() works.  The reason
  this is important to fix is because when trace_printk() doesn't have
  any arguments, it turns into a trace_puts().  Not being able to enable
  a stack trace against trace_printk() because it does not have any
  arguments is quite confusing.  Also, the fix is rather trivial and low
  risk.

  While porting some changes to PowerPC I discovered that it still has
  the function graph tracer filter bug that if you also enable stack
  tracing the function graph tracer filter is ignored.  I fixed that up.

  Finally, Martin Lau, fixed a bug that would cause readers of the
  ftrace ring buffer to block forever even though it was suppose to be
  NONBLOCK"

This also includes the fix from an earlier pull request:

"Oleg Nesterov fixed a memory leak that happens if a user creates a
  tracing instance, sets up a filter in an event, and then removes that
  instance.  The filter allocates memory that is never freed when the
  instance is destroyed"

* tag 'trace-fixes-v3.16-rc5-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ring-buffer: Fix polling on trace_pipe
  tracing: Add TRACE_ITER_PRINTK flag check in __trace_puts/__trace_bputs
  tracing: Fix graph tracer with stack tracer on other archs
  tracing: Add ftrace_trace_stack into __trace_puts/__trace_bputs
  tracing: instance_rmdir() leaks ftrace_event_file->filter

Merge tag 'for-linus-20140716' of git://git.infradead.org/linux-mtd

Pull MTD fixes from Brian Norris:

- Fix ELM suspend/resume

- Reduce warnings if NAND ECC is too weak

- Add CFI support for Sharp LH28F640BF NOR

   The last fix is coming in because other commits in the 3.16 cycle
   depended on this support.

* tag 'for-linus-20140716' of git://git.infradead.org/linux-mtd:
  mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR
  mtd: nand: reduce the warning noise when the ECC is too weak
  mtd: devices: elm: fix elm_context_save() and elm_context_restore() functions

Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Ingo Molnar:
"A cpufreq lockup fix and a compiler warning fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix compiler warnings
x86, tsc: Fix cpufreq lockup

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Ingo Molnar:
"Tooling fixes and an Intel PMU driver fixlet"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Do not allow optimized switch for non-cloned events
  perf/x86/intel: ignore CondChgd bit to avoid false NMI handling
  perf symbols: Get kernel start address by symbol name
  perf tools: Fix segfault in cumulative.callchain report

Merge tag 'sound-3.16-rc6' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"Things seem to calm down so far, just a small few HD-audio fixes
  (regression fixes and a new codec ID addition) popping up"

* tag 'sound-3.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix broken PM due to incomplete i915 initialization
  ALSA: hda - Revert stream assignment order for Intel controllers
  ALSA: hda - Add new GPU codec ID 0x10de0070 to snd-hda
  ALSA: hda: Fix build warning

UBI: fastmap: do not miss bit-flips

The return value from 'ubi_io_read_ec_hdr()' was stored in 'err', not in 'ret'.
This fix makes sure Fastmap-enabled UBI does not miss bit-flip while reading EC
headers, events and scrubs the affected PEBs.

This issue was reported by Coverity Scan.

Artem: improved the commit message.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs

Pull quota fix from Jan Kara:
"Fix locking of dquot shrinker"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: missing lock in dqcache_shrink_scan()

Merge tag 'gpio-v3.16-3' of git://git./linux/kernel/git/linusw/linux-gpio

Pull GPIO fix from Linus Walleij:
"Fix up some merge confusion from the merge window"

* tag 'gpio-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mcp23s08: Eliminates redundant checking.

ring-buffer: Fix polling on trace_pipe

ring_buffer_poll_wait() should always put the poll_table to its wait_queue
even there is immediate data available.  Otherwise, the following epoll and
read sequence will eventually hang forever:

1. Put some data to make the trace_pipe ring_buffer read ready first
2. epoll_ctl(efd, EPOLL_CTL_ADD, trace_pipe_fd, ee)
3. epoll_wait()
4. read(trace_pipe_fd) till EAGAIN
5. Add some more data to the trace_pipe ring_buffer
6. epoll_wait() -> this epoll_wait() will block forever

~ During the epoll_ctl(efd, EPOLL_CTL_ADD,...) call in step 2,
  ring_buffer_poll_wait() returns immediately without adding poll_table,
  which has poll_table->_qproc pointing to ep_poll_callback(), to its
  wait_queue.
~ During the epoll_wait() call in step 3 and step 6,
  ring_buffer_poll_wait() cannot add ep_poll_callback() to its wait_queue
  because the poll_table->_qproc is NULL and it is how epoll works.
~ When there is new data available in step 6, ring_buffer does not know
  it has to call ep_poll_callback() because it is not in its wait queue.
  Hence, block forever.

Other poll implementation seems to call poll_wait() unconditionally as the very
first thing to do.  For example, tcp_poll() in tcp.c.

Link: http://lkml.kernel.org/p/20140610060637.GA14045@devbig242.prn2.facebook.com
Cc: stable@vger.kernel.org # 2.6.27
Fixes: 2a2cc8f7c4d0 "ftrace: allow the event pipe to be polled"
Reviewed-by: Chris Mason <clm@fb.com>
Signed-off-by: Martin Lau <kafai@fb.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

quota: missing lock in dqcache_shrink_scan()

Commit 1ab6c4997e04 (fs: convert fs shrinkers to new scan/count API)
accidentally removed locking from quota shrinker. Fix it -
dqcache_shrink_scan() should use dq_list_lock to protect the
scan on free_dquots list.

CC: stable@vger.kernel.org
Fixes: 1ab6c4997e04a00c50c6d786c2f046adc0d1f5de
Signed-off-by: Niu Yawei <yawei.niu@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>

dm cache metadata: do not allow the data block size to change

The block size for the dm-cache's data device must remained fixed for
the life of the cache. Disallow any attempt to change the cache's data
block size.

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org

dm thin metadata: do not allow the data block size to change

The block size for the thin-pool's data device must remained fixed for
the life of the thin-pool. Disallow any attempt to change the
thin-pool's data block size.

It should be noted that attempting to change the data block size via
thin-pool table reload will be ignored as a side-effect of the thin-pool
handover that the thin-pool target does during thin-pool table reload.

Here is an example outcome of attempting to load a thin-pool table that
reduced the thin-pool's data block size from 1024K to 512K.

Before:
kernel: device-mapper: thin: 253:4: growing the data device from 204800 to 409600 blocks

After:
kernel: device-mapper: thin metadata: changing the data block size (from 2048 to 1024) is not supported
kernel: device-mapper: table: 253:4: thin-pool: Error creating metadata object
kernel: device-mapper: ioctl: error adding target to table

Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org

tracing: Add TRACE_ITER_PRINTK flag check in __trace_puts/__trace_bputs

The TRACE_ITER_PRINTK check in __trace_puts/__trace_bputs is missing,
so add it, to be consistent with __trace_printk/__trace_bprintk.
Those functions are all called by the same function: trace_printk().

Link: http://lkml.kernel.org/p/51E7A7D6.8090900@huawei.com
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/mszeredi/fuse

Pull fuse fixes from Miklos Szeredi:
"This contains miscellaneous fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: replace count*size kzalloc by kcalloc
  fuse: release temporary page if fuse_writepage_locked() failed
  fuse: restructure ->rename2()
  fuse: avoid scheduling while atomic
  fuse: handle large user and group ID
  fuse: inode: drop cast
  fuse: ignore entry-timeout on LOOKUP_REVAL
  fuse: timeout comparison fix

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) Bluetooth pairing fixes from Johan Hedberg.

2) ieee80211_send_auth() doesn't allocate enough tail room for the SKB,
    from Max Stepanov.

3) New iwlwifi chip IDs, from Oren Givon.

4) bnx2x driver reads wrong PCI config space MSI register, from Yijing
    Wang.

5) IPV6 MLD Query validation isn't strong enough, from Hangbin Liu.

6) Fix double SKB free in openvswitch, from Andy Zhou.

7) Fix sk_dst_set() being racey with UDP sockets, leading to strange
    crashes, from Eric Dumazet.

8) Interpret the NAPI budget correctly in the new systemport driver,
    from Florian Fainelli.

9) VLAN code frees percpu stats in the wrong place, leading to crashes
    in the get stats handler.  From Eric Dumazet.

10) TCP sockets doing a repair can crash with a divide by zero, because
    we invoke tcp_push() with an MSS value of zero.  Just skip that part
    of the sendmsg paths in repair mode.  From Christoph Paasch.

11) IRQ affinity bug fixes in mlx4 driver from Amir Vadai.

12) Don't ignore path MTU icmp messages with a zero mtu, machines out
    there still spit them out, and all of our per-protocol handlers for
    PMTU can cope with it just fine.  From Edward Allcutt.

13) Some NETDEV_CHANGE notifier invocations were not passing in the
    correct kind of cookie as the argument, from Loic Prylli.

14) Fix crashes in long multicast/broadcast reassembly, from Jon Paul
    Maloy.

15) ip_tunnel_lookup() doesn't interpret wildcard keys correctly, fix
    from Dmitry Popov.

16) Fix skb->sk assigned without taking a reference to 'sk' in
    appletalk, from Andrey Utkin.

17) Fix some info leaks in ULP event signalling to userspace in SCTP,
    from Daniel Borkmann.

18) Fix deadlocks in HSO driver, from Olivier Sobrie.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
  hso: fix deadlock when receiving bursts of data
  hso: remove unused workqueue
  net: ppp: don't call sk_chk_filter twice
  mlx4: mark napi id for gro_skb
  bonding: fix ad_select module param check
  net: pppoe: use correct channel MTU when using Multilink PPP
  neigh: sysctl - simplify address calculation of gc_* variables
  net: sctp: fix information leaks in ulpevent layer
  MAINTAINERS: update r8169 maintainer
  net: bcmgenet: fix RGMII_MODE_EN bit
  tipc: clear 'next'-pointer of message fragments before reassembly
  r8152: fix r8152_csum_workaround function
  be2net: set EQ DB clear-intr bit in be_open()
  GRE: enable offloads for GRE
  farsync: fix invalid memory accesses in fst_add_one() and fst_init_card()
  igb: do a reset on SR-IOV re-init if device is down
  igb: Workaround for i210 Errata 25: Slow System Clock
  usbnet: smsc95xx: add reset_resume function with reset operation
  dp83640: Always decode received status frames
  r8169: disable L23
  ...

tracing: Fix graph tracer with stack tracer on other archs

Running my ftrace tests on PowerPC, it failed the test that checks
if function_graph tracer is affected by the stack tracer. It was.
Looking into this, I found that the update_function_graph_func()
must be called even if the trampoline function is not changed.
This is because archs like PowerPC do not support ftrace_ops being
passed by assembly and instead uses a helper function (what the
trampoline function points to). Since this function is not changed
even when multiple ftrace_ops are added to the code, the test that
falls out before calling update_function_graph_func() will miss that
the update must still be done.

Call update_function_graph_function() for all calls to
update_ftrace_function()

Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

tracing: Add ftrace_trace_stack into __trace_puts/__trace_bputs

Currently trace option stacktrace is not applicable for
trace_printk with constant string argument, the reason is
in __trace_puts/__trace_bputs ftrace_trace_stack is missing.

In contrast, when using trace_printk with non constant string
argument(will call into __trace_printk/__trace_bprintk), then
trace option stacktrace is workable, this inconstant result
will confuses users a lot.

Link: http://lkml.kernel.org/p/51E7A7C9.9040401@huawei.com
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

ALSA: hda - Fix broken PM due to incomplete i915 initialization

When the initialization of Intel HDMI controller fails due to missing
i915 kernel symbols (e.g. HD-audio is built in while i915 is module),
the driver discontinues the probe. However, since the probe was done
asynchronously, the driver object still remains, thus the relevant PM
ops are still called at suspend/resume. This results in the bad access
to the incomplete audio card object, eventually leads to Oops or stall
at PM.

This patch adds the missing checks of chip->init_failed flag at each
PM callback in order to fix the problem above.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79561
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

hso: fix deadlock when receiving bursts of data

When the module sends bursts of data, sometimes a deadlock happens in
the hso driver when the tty buffer doesn't get the chance to be flushed
quickly enough.

Remove the endless while loop in function put_rxbuf_data() which is
called by the urb completion handler.
If there isn't enough room in the tty buffer, discards all the data
received in the URB.

Cc: David Miller <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jan Dumon <j.dumon@option.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

hso: remove unused workqueue

The workqueue "retry_unthrottle_workqueue" is not scheduled anywhere
in the code. So, remove it.

Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'firewire-fix' of git://git./linux/kernel/git/ieee1394/linux1394

Pull firewire fix from Stefan Richter:
"The 1394 drivers cannot and are not supposed to be built on platforms
  which don't provide the DMA mapping API (regression since v3.16-rc1
  with CONFIG_COMPILE_TEST=y on some architectures)"

* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: IEEE 1394 (FireWire) support should depend on HAS_DMA

Merge git://git.kvack.org/~bcrl/aio-fixes

Pull another aio fix from Ben LaHaise:
"put_reqs_available() can now be called from within irq context, which
  means that it (and its sibling function get_reqs_available()) now need
  to be irq-safe, not just preempt-safe"

* git://git.kvack.org/~bcrl/aio-fixes:
  aio: protect reqs_available updates from changes in interrupt handlers

net/l2tp: don't fall back on UDP [get|set]sockopt

The l2tp [get|set]sockopt() code has fallen back to the UDP functions
for socket option levels != SOL_PPPOL2TP since day one, but that has
never actually worked, since the l2tp socket isn't an inet socket.

As David Miller points out:

"If we wanted this to work, it'd have to look up the tunnel and then
use tunnel->sk, but I wonder how useful that would be"

Since this can never have worked so nobody could possibly have depended
on that functionality, just remove the broken code and return -EINVAL.

Reported-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: James Chapman <jchapman@katalix.com>
Acked-by: David Miller <davem@davemloft.net>
Cc: Phil Turnbull <phil.turnbull@oracle.com>
Cc: Vegard Nossum <vegard.nossum@oracle.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

net: ppp: don't call sk_chk_filter twice

Commit 568f194e8bd16c353ad50f9ab95d98b20578a39d ("net: ppp: use
sk_unattached_filter api") causes sk_chk_filter() to be called twice when
setting a PPP pass or active filter. This applies to both the generic PPP
subsystem implemented by drivers/net/ppp/ppp_generic.c and the ISDN PPP
subsystem implemented by drivers/isdn/i4l/isdn_ppp.c. The first call is from
within get_filter(). The second one is through the call chain

  ppp_ioctl() or isdn_ppp_ioctl()
  --> sk_unattached_filter_create()
      --> __sk_prepare_filter()
          --> sk_chk_filter()

The first call from within get_filter() should be deleted as get_filter() is
called just before calling sk_unattached_filter_create() later on, which
eventually calls sk_chk_filter() anyway.

For 3.15.x, this proposed change is a bugfix rather than a pure optimization as
in that branch, sk_chk_filter() may replace filter codes by other codes which
are not recognized when executing sk_chk_filter() a second time. So with
3.15.x, if sk_chk_filter() is called twice, the second invocation may yield
EINVAL (this depends on the filter codes found in the filter to be set, but
because the replacement is done for frequently used codes, this is almost
always the case). The net effect is that setting pass and/or active PPP filters
does not work anymore, since sk_unattached_filter_create() always returns
EINVAL due to the second call to sk_chk_filter(), regardless whether the filter
was originally sane or not.

Signed-off-by: Christoph Schulz <develop@kristov.de>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4: mark napi id for gro_skb

Napi id was not marked for gro_skb, this will lead rx busy loop won't
work correctly since they stack never try to call low latency receive
method because of a zero socket napi id. Fix this by marking napi id
for gro_skb.

The transaction rate of 1 byte netperf tcp_rr gets about 50% increased
(from 20531.68 to 30610.88).

Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix ad_select module param check

Obvious copy/paste error when I converted the ad_select to the new
option API. "lacp_rate" there should be "ad_select" so we can get the
proper value.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Fixes: 9e5f5eebe765 ("bonding: convert ad_select to use the new option
API")
Reported-by: Karim Scheik <karim.scheik@prisma-solutions.at>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: pppoe: use correct channel MTU when using Multilink PPP

The PPP channel MTU is used with Multilink PPP when ppp_mp_explode() (see
ppp_generic module) tries to determine how big a fragment might be. According
to RFC 1661, the MTU excludes the 2-byte PPP protocol field, see the
corresponding comment and code in ppp_mp_explode():

/*
* hdrlen includes the 2-byte PPP protocol field, but the
* MTU counts only the payload excluding the protocol field.
* (RFC1661 Section 2)
*/
mtu = pch->chan->mtu - (hdrlen - 2);

However, the pppoe module *does* include the PPP protocol field in the channel
MTU, which is wrong as it causes the PPP payload to be 1-2 bytes too big under
certain circumstances (one byte if PPP protocol compression is used, two
otherwise), causing the generated Ethernet packets to be dropped. So the pppoe
module has to subtract two bytes from the channel MTU. This error only
manifests itself when using Multilink PPP, as otherwise the channel MTU is not
used anywhere.

In the following, I will describe how to reproduce this bug. We configure two
pppd instances for multilink PPP over two PPPoE links, say eth2 and eth3, with
a MTU of 1492 bytes for each link and a MRRU of 2976 bytes. (This MRRU is
computed by adding the two link MTUs and subtracting the MP header twice, which
is 4 bytes long.) The necessary pppd statements on both sides are "multilink
mtu 1492 mru 1492 mrru 2976". On the client side, we additionally need "plugin
rp-pppoe.so eth2" and "plugin rp-pppoe.so eth3", respectively; on the server
side, we additionally need to start two pppoe-server instances to be able to
establish two PPPoE sessions, one over eth2 and one over eth3. We set the MTU
of the PPP network interface to the MRRU (2976) on both sides of the connection
in order to make use of the higher bandwidth. (If we didn't do that, IP
fragmentation would kick in, which we want to avoid.)

Now we send a ICMPv4 echo request with a payload of 2948 bytes from client to
server over the PPP link. This results in the following network packet:

   2948 (echo payload)
+    8 (ICMPv4 header)
+   20 (IPv4 header)
---------------------
   2976 (PPP payload)

These 2976 bytes do not exceed the MTU of the PPP network interface, so the
IP packet is not fragmented. Now the multilink PPP code in ppp_mp_explode()
prepends one protocol byte (0x21 for IPv4), making the packet one byte bigger
than the negotiated MRRU. So this packet would have to be divided in three
fragments. But this does not happen as each link MTU is assumed to be two bytes
larger. So this packet is diveded into two fragments only, one of size 1489 and
one of size 1488. Now we have for that bigger fragment:

   1489 (PPP payload)
+    4 (MP header)
+    2 (PPP protocol field for the MP payload (0x3d))
+    6 (PPPoE header)
--------------------------
   1501 (Ethernet payload)

This packet exceeds the link MTU and is discarded.

If one configures the link MTU on the client side to 1501, one can see the
discarded Ethernet frames with tcpdump running on the client. A

ping -s 2948 -c 1 192.168.15.254

leads to the smaller fragment that is correctly received on the server side:

(tcpdump -vvvne -i eth3 pppoes and ppp proto 0x3d)
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x3] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [end], length 1492

and to the bigger fragment that is not received on the server side:

(tcpdump -vvvne -i eth2 pppoes and ppp proto 0x3d)
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
  length 1515: PPPoE  [ses 0x5] MLPPP (0x003d), length 1495: seq 0x000,
  Flags [begin], length 1493

With the patch below, we correctly obtain three fragments:

52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [begin], length 1492
52:54:00:70:9e:89 > 52:54:00:5d:6f:b0, ethertype PPPoE S (0x8864),
  length 1514: PPPoE  [ses 0x1] MLPPP (0x003d), length 1494: seq 0x000,
  Flags [none], length 1492
52:54:00:ad:87:fd > 52:54:00:79:5c:d0, ethertype PPPoE S (0x8864),
  length 27: PPPoE  [ses 0x1] MLPPP (0x003d), length 7: seq 0x000,
  Flags [end], length 5

And the ICMPv4 echo request is successfully received at the server side:

IP (tos 0x0, ttl 64, id 21925, offset 0, flags [DF], proto ICMP (1),
  length 2976)
    192.168.222.2 > 192.168.15.254: ICMP echo request, id 30530, seq 0,
      length 2956

The bug was introduced in commit c9aa6895371b2a257401f59d3393c9f7ac5a8698
("[PPPOE]: Advertise PPPoE MTU") from the very beginning. This patch applies
to 3.10 upwards but the fix can be applied (with minor modifications) to
kernels as old as 2.6.32.

Signed-off-by: Christoph Schulz <develop@kristov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

neigh: sysctl - simplify address calculation of gc_* variables

The code in neigh_sysctl_register() relies on a specific layout of
struct neigh_table, namely that the 'gc_*' variables are directly
following the 'parms' member in a specific order. The code, though,
expresses this in the most ugly way.

Get rid of the ugly casts and use the 'tbl' pointer to get a handle to
the table. This way we can refer to the 'gc_*' variables directly.

Similarly seen in the grsecurity patch, written by Brad Spengler.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Brad Spengler <spender@grsecurity.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfs: null unused quota inodes when quota is on

When quota is on, it is expected that unused quota inodes have a
value of NULLFSINO. The changes to support a separate project quota
in 3.12 broken this rule for non-project quota inode enabled
filesystem, as the code now refuses to write the group quota inode
if neither group or project quotas are enabled. This regression was
introduced by commit d892d58 ("xfs: Start using pquotaino from the
superblock").

In this case, we should be writing NULLFSINO rather than nothing to
ensure that we leave the group quota inode in a valid state while
quotas are enabled.

Failure to do so doesn't cause a current kernel to break - the
separate project quota inodes introduced translation code to always
treat a zero inode as NULLFSINO. This was introduced by commit
0102629 ("xfs: Initialize all quota inodes to be NULLFSINO") with is
also in 3.12 but older kernels do not do this and hence taking a
filesystem back to an older kernel can result in quotas failing
initialisation at mount time. When that happens, we see this in
dmesg:

[ 1649.215390] XFS (sdb): Mounting Filesystem
[ 1649.316894] XFS (sdb): Failed to initialize disk quotas.
[ 1649.316902] XFS (sdb): Ending clean mount

By ensuring that we write NULLFSINO to quota inodes that aren't
active, we avoid this problem. We have to be really careful when
determining if the quota inodes are active or not, because we don't
want to write a NULLFSINO if the quota inodes are active and we
simply aren't updating them.

Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>

net: sctp: fix information leaks in ulpevent layer

While working on some other SCTP code, I noticed that some
structures shared with user space are leaking uninitialized
stack or heap buffer. In particular, struct sctp_sndrcvinfo
has a 2 bytes hole between .sinfo_flags and .sinfo_ppid that
remains unfilled by us in sctp_ulpevent_read_sndrcvinfo() when
putting this into cmsg. But also struct sctp_remote_error
contains a 2 bytes hole that we don't fill but place into a skb
through skb_copy_expand() via sctp_ulpevent_make_remote_error().

Both structures are defined by the IETF in RFC6458:

* Section 5.3.2. SCTP Header Information Structure:

  The sctp_sndrcvinfo structure is defined below:

  struct sctp_sndrcvinfo {
    uint16_t sinfo_stream;
    uint16_t sinfo_ssn;
    uint16_t sinfo_flags;
    <-- 2 bytes hole  -->
    uint32_t sinfo_ppid;
    uint32_t sinfo_context;
    uint32_t sinfo_timetolive;
    uint32_t sinfo_tsn;
    uint32_t sinfo_cumtsn;
    sctp_assoc_t sinfo_assoc_id;
  };

* 6.1.3. SCTP_REMOTE_ERROR:

  A remote peer may send an Operation Error message to its peer.
  This message indicates a variety of error conditions on an
  association. The entire ERROR chunk as it appears on the wire
  is included in an SCTP_REMOTE_ERROR event. Please refer to the
  SCTP specification [RFC4960] and any extensions for a list of
  possible error formats. An SCTP error notification has the
  following format:

  struct sctp_remote_error {
    uint16_t sre_type;
    uint16_t sre_flags;
    uint32_t sre_length;
    uint16_t sre_error;
    <-- 2 bytes hole  -->
    sctp_assoc_t sre_assoc_id;
    uint8_t  sre_data[];
  };

Fix this by setting both to 0 before filling them out. We also
have other structures shared between user and kernel space in
SCTP that contains holes (e.g. struct sctp_paddrthlds), but we
copy that buffer over from user space first and thus don't need
to care about it in that cases.

While at it, we can also remove lengthy comments copied from
the draft, instead, we update the comment with the correct RFC
number where one can look it up.

Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xfs: refine the allocation stack switch

The allocation stack switch at xfs_bmapi_allocate() has served it's
purpose, but is no longer a sufficient solution to the stack usage
problem we have in the XFS allocation path.

Whilst the kernel stack size is now 16k, that is not a valid reason
for undoing all our "keep stack usage down" modifications. What it
does allow us to do is have the freedom to refine and perfect the
modifications knowing that if we get it wrong it won't blow up in
our faces - we have a safety net now.

This is important because we still have the issue of older kernels
having smaller stacks and that they are still supported and are
demonstrating a wide range of different stack overflows. Red Hat
has several open bugs for allocation based stack overflows from
directory modifications and direct IO block allocation and these
problems still need to be solved. If we can solve them upstream,
then distro's won't need to bake their own unique solutions.

To that end, I've observed that every allocation based stack
overflow report has had a specific characteristic - it has happened
during or directly after a bmap btree block split. That event
requires a new block to be allocated to the tree, and so we
effectively stack one allocation stack on top of another, and that's
when we get into trouble.

A further observation is that bmap btree block splits are much rarer
than writeback allocation - over a range of different workloads I've
observed the ratio of bmap btree inserts to splits ranges from 100:1
(xfstests run) to 10000:1 (local VM image server with sparse files
that range in the hundreds of thousands to millions of extents).
Either way, bmap btree split events are much, much rarer than
allocation events.

Finally, we have to move the kswapd state to the allocation workqueue
work when allocation is done on behalf of kswapd. This is proving to
cause significant perturbation in performance under memory pressure
and appears to be generating allocation deadlock warnings under some
workloads, so avoiding the use of a workqueue for the majority of
kswapd writeback allocation will minimise the impact of such
behaviour.

Hence it makes sense to move the stack switch to xfs_btree_split()
and only do it for bmap btree splits. Stack switches during
allocation will be much rarer, so there won't be significant
performacne overhead caused by switching stacks. The worse case
stack from all allocation paths will be split, not just writeback.
And the majority of memory allocations will be done in the correct
context (e.g. kswapd) without causing additional latency, and so we
simplify the memory reclaim interactions between processes,
workqueues and kswapd.

The worst stack I've been able to generate with this patch in place
is 5600 bytes deep. It's very revealing because we exit XFS at:

37) 1768 64 kmem_cache_alloc+0x13b/0x170

about 1800 bytes of stack consumed, and the remaining 3800 bytes
(and 36 functions) is memory reclaim, swap and the IO stack. And
this occurs in the inode allocation from an open(O_CREAT) syscall,
not writeback.

The amount of stack being used is much less than I've previously be
able to generate - fs_mark testing has been able to generate stack
usage of around 7k without too much trouble; with this patch it's
only just getting to 5.5k. This is primarily because the metadata
allocation paths (e.g. directory blocks) are no longer causing
double splits on the same stack, and hence now stack tracing is
showing swapping being the worst stack consumer rather than XFS.

Performance of fs_mark inode create workloads is unchanged.
Performance of fs_mark async fsync workloads is consistently good
with context switches reduced by around 150,000/s (30%).
Performance of dbench, streaming IO and postmark is unchanged.
Allocation deadlock warnings have not been seen on the workloads
that generated them since adding this patch.

Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>

Revert "xfs: block allocation work needs to be kswapd aware"

This reverts commit 1f6d64829db78a7e1d63e15c9f48f0a5d2b5a679.

This commit resulted in regressions in performance in low
memory situations where kswapd was doing writeback of delayed
allocation blocks. It resulted in significant parallelism of the
kswapd work and with the special kswapd flags meant that hundreds of
active allocation could dip into kswapd specific memory reserves and
avoid being throttled. This cause a large amount of performance
variation, as well as random OOM-killer invocations that didn't
previously exist.

Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>

tracing: instance_rmdir() leaks ftrace_event_file->filter

instance_rmdir() path destroys the event files but forgets to free
file->filter. Change remove_event_file_dir() to free_event_filter().

Link: http://lkml.kernel.org/p/20140711190638.GA19517@redhat.com
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: "zhangwei(Jovi)" <jovi.zhangwei@huawei.com>
Cc: stable@vger.kernel.org # 3.11+
Fixes: f6a84bdc75b5 "tracing: Introduce remove_event_file_dir()"
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>

aio: protect reqs_available updates from changes in interrupt handlers

As of commit f8567a3845ac05bb28f3c1b478ef752762bd39ef it is now possible to
have put_reqs_available() called from irq context.  While put_reqs_available()
is per cpu, it did not protect itself from interrupts on the same CPU.  This
lead to aio_complete() corrupting the available io requests count when run
under a heavy O_DIRECT workloads as reported by Robert Elliott.  Fix this by
disabling irq updates around the per cpu batch updates of reqs_available.

Many thanks to Robert and folks for testing and tracking this down.

Reported-by: Robert Elliot <Elliott@hp.com>
Tested-by: Robert Elliot <Elliott@hp.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: Jens Axboe <axboe@kernel.dk>, Christoph Hellwig <hch@infradead.org>
Cc: stable@vger.kenel.org

fuse: replace count*size kzalloc by kcalloc

kcalloc manages count*sizeof overflow.

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>

fuse: release temporary page if fuse_writepage_locked() failed

tmp_page to be freed if fuse_write_file_get() returns NULL.

Signed-off-by: Maxim Patlasov <mpatlasov@parallels.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>

ALSA: hda - Revert stream assignment order for Intel controllers

We got a regression report for 3.15.x kernels, and this turned out to
be triggered by the fix for stream assignment order. On reporter's
machine with Intel controller (8086:1e20) + VIA VT1802 codec, the
first playback slot can't work with speaker outputs.

But the original commit was actually a fix for AMD controllers where
no proper GCAP value is returned, we shouldn't revert the whole
commit. Instead, in this patch, a new flag is introduced to determine
the stream assignment order, and follow the old behavior for Intel
controllers.

Fixes: dcb32ecd9a53 ('ALSA: hda - Do not assign streams in reverse order')
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Cc: <stable@vger.kernel.org> [v3.15+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>

MAINTAINERS: update r8169 maintainer

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: bcmgenet: fix RGMII_MODE_EN bit

RGMII_MODE_EN bit was defined to 0, while it is actually 6. It was not
much of a problem on older designs where this was a no-op, and the RGMII
data-path would always be enabled, but newer GENET controllers need to
explicitely enable their RGMII data-pad using this bit.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mtd: cfi_cmdset_0001.c: add support for Sharp LH28F640BF NOR

This family of chips was long ago supported by the pre-cfi driver.
CFI code tested on several Zaurus SL-5500 (Collie) 2x16 on 32 bit bus.

Function is_LH28F640BF() mimics is_m29ew() from cmdset_0002.c

Buffer write fixes as seen in 2007 patch c/o
Anti Sullin <anti.sullin <at> artecdesign.ee>
http://comments.gmane.org/gmane.linux.ports.arm.kernel/36733

[Brian: this patch is semi-urgent, because the following patch switches
  to using CFI detection for a chip which (until now) is unsupported by
  the CFI driver

  9218310  ARM: 8084/1: sa1100: collie: revert back to cfi_probe
]

Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

mtd: nand: reduce the warning noise when the ECC is too weak

In commit 67a9ad9b8a6f ("mtd: nand: Warn the user if the selected ECC
strength is too weak"), a check was added to inform the user when the
ECC used for a NAND device is weaker than the recommended ECC
advertised by the NAND chip. However, the warning uses WARN_ON(),
which has two undesirable side-effects:

- It just prints to the kernel log the fact that there is a warning
   in this file, at this line, but it doesn't explain anything about
   the warning itself.

- It dumps a stack trace which is very noisy, for something that the
   user is most likely not able to fix. If a certain ECC used by the
   kernel is weaker than the advertised one, it's most likely to make
   sure the kernel uses an ECC that is compatible with the one used by
   the bootloader, and changing the bootloader may not necessarily be
   easy. Therefore, normal users would not be able to do anything to
   fix this very noisy warning, and will have to suffer from it at
   every kernel boot. At least every time I see this stack trace in my
   kernel boot log, I wonder what new thing is broken, just to realize
   that it's once again this NAND ECC warning.

Therefore, this commit turns:

------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at /home/thomas/projets/linux-2.6/drivers/mtd/nand/nand_base.c:4051 nand_scan_tail+0x538/0x780()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.16.0-rc3-dirty #4
[<c000e3dc>] (unwind_backtrace) from [<c000bee4>] (show_stack+0x10/0x14)
[<c000bee4>] (show_stack) from [<c0018180>] (warn_slowpath_common+0x6c/0x8c)
[<c0018180>] (warn_slowpath_common) from [<c001823c>] (warn_slowpath_null+0x1c/0x24)
[<c001823c>] (warn_slowpath_null) from [<c02c50cc>] (nand_scan_tail+0x538/0x780)
[<c02c50cc>] (nand_scan_tail) from [<c0639f78>] (orion_nand_probe+0x224/0x2e4)
[<c0639f78>] (orion_nand_probe) from [<c026da00>] (platform_drv_probe+0x18/0x4c)
[<c026da00>] (platform_drv_probe) from [<c026c1f4>] (really_probe+0x80/0x218)
[<c026c1f4>] (really_probe) from [<c026c47c>] (__driver_attach+0x98/0x9c)
[<c026c47c>] (__driver_attach) from [<c026a8f0>] (bus_for_each_dev+0x64/0x94)
[<c026a8f0>] (bus_for_each_dev) from [<c026bae4>] (bus_add_driver+0x144/0x1ec)
[<c026bae4>] (bus_add_driver) from [<c026cb00>] (driver_register+0x78/0xf8)
[<c026cb00>] (driver_register) from [<c026da5c>] (platform_driver_probe+0x20/0xb8)
[<c026da5c>] (platform_driver_probe) from [<c00088b8>] (do_one_initcall+0x80/0x1d8)
[<c00088b8>] (do_one_initcall) from [<c0620c9c>] (kernel_init_freeable+0xf4/0x1b4)
[<c0620c9c>] (kernel_init_freeable) from [<c049a098>] (kernel_init+0x8/0xec)
[<c049a098>] (kernel_init) from [<c00095f0>] (ret_from_fork+0x14/0x24)
---[ end trace 62f87d875aceccb4 ]---

Into the much shorter, and much more useful:

nand: WARNING: MT29F2G08ABAEAWP: the ECC used on your system is too weak compared to the one required by the NAND chip

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Linux 3.16-rc5

Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4

Pull ext4 bugfixes from Ted Ts'o:
"More bug fixes for ext4 -- most importantly, a fix for a bug
  introduced in 3.15 that can end up triggering a file system corruption
  error after a journal replay.

  It shouldn't lead to any actual data corruption, but it is scary and
  can force file systems to be remounted read-only, etc"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix potential null pointer dereference in ext4_free_inode
  ext4: fix a potential deadlock in __ext4_es_shrink()
  ext4: revert commit which was causing fs corruption after journal replays
  ext4: disable synchronous transaction batching if max_batch_time==0
  ext4: clarify ext4_error message in ext4_mb_generate_buddy_error()
  ext4: clarify error count warning messages
  ext4: fix unjournalled bg descriptor while initializing inode bitmap

Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux

Pull clock driver fixes from Mike Turquette:
"This batch of fixes is for a handful of clock drivers from Allwinner,
  Samsung, ST & TI.  Most of them are of the "this hardware won't work
  without this fix" variety, including patches that fix platforms that
  did not boot under certain configurations.  Other fixes are the result
  of changes to the clock core introduced in 3.15 that had subtle
  impacts on the clock drivers.

  There are no fixes to the clock framework core in this pull request"

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
  clk: spear3xx: Set proper clock parent of uart1/2
  clk: spear3xx: Use proper control register offset
  clk: qcom: HDMI source sel is 3 not 2
  clk: sunxi: fix devm_ioremap_resource error detection code
  clk: s2mps11: Fix double free corruption during driver unbind
  clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
  clk: exynos5420: Remove aclk66_peric from the clock tree description
  clk/exynos5250: fix bit number for tv sysmmu clock
  clk: s3c64xx: Hookup SPI clocks correctly
  clk: samsung: exynos4: Remove SRC_MASK_ISP gates
  clk: samsung: add more aliases for s3c24xx
  clk: samsung: fix several typos to fix boot on s3c2410
  clk: ti: set CLK_SET_RATE_NO_REPARENT for ti,mux-clock
  clk: ti: am43x: Fix boot with CONFIG_SOC_AM33XX disabled
  clk: ti: dra7: return error code in failure case
  clk: ti: apll: not allocating enough data

Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Olof Johansson:
"This week's arm-soc fixes:

   - Another set of OMAP fixes
     * Clock fixes
     * Restart handling
     * PHY regulators
     * SATA hwmod data for DRA7
     + Some trivial fixes and removal of a bit of dead code
   - Exynos fixes
     * A bunch of clock fixes
     * Some SMP fixes
     * Exynos multi-core timer: register as clocksource and fix ftrace.
     + a few other minor fixes

  There's also a couple more patches, and at91 fix for USB caused by
  common clock conversion, and more MAINTAINERS entries for shmobile.

  We're definitely switching to only regression fixes from here on out,
  we've been a little less strict than usual up until now"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
  ARM: at91: at91sam9x5: add clocks for usb device
  ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
  ARM: dts: Add clock property for mfc_pd in exynos5420
  clk: exynos5420: Add IDs for clocks used in PD mfc
  ARM: EXYNOS: Add support for clock handling in power domain
  ARM: OMAP2+: Remove non working OMAP HDMI audio initialization
  ARM: imx: fix shared gate clock
  ARM: dts: Update the parent for Audss clocks in Exynos5420
  ARM: EXYNOS: Update secondary boot addr for secure mode
  ARM: dts: Fix TI CPSW Phy mode selection on IGEP COM AQUILA.
  ARM: dts: am335x-evmsk: Enable the McASP FIFO for audio
  ARM: dts: am335x-evm: Enable the McASP FIFO for audio
  ARM: OMAP2+: Make GPMC skip disabled devices
  ARM: OMAP2+: create dsp device only on OMAP3 SoCs
  ARM: dts: dra7-evm: Make VDDA_1V8_PHY supply always on
  ARM: DRA7/AM43XX: fix header definition for omap44xx_restart
  ARM: OMAP2+: clock/dpll: fix _dpll_test_fint arithmetics overflow
  ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss
  ARM: DRA7: hwmod: Fixup SATA hwmod
  ARM: OMAP3: PRM/CM: Add back macros used by TI DSP/Bridge driver
  ...

Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm

Pull ARM fixes from Russell King:
"Another round of fixes for ARM:
   - a set of kprobes fixes from Jon Medhurst
   - fix the revision checking for the L2 cache which wasn't noticed to
     have been broken"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: l2c: fix revision checking
  ARM: kprobes: Fix test code compilation errors for ARMv4 targets
  ARM: kprobes: Disallow instructions with PC and register specified shift
  ARM: kprobes: Prevent known test failures stopping other tests running

Merge branch 'for-linus' of git://git./linux/kernel/git/geert/linux-m68k

Pull m68k fixes from Geert Uytterhoeven:
"Summary:
  - Fix for a boot regression introduced in v3.16-rc1,
  - Fix for a build issue in -next"

Christoph Hellwig questioned why mach_random_get_entropy should be
exported to modules, and Geert explains that random_get_entropy() is
called by at least the crypto layer and ends up using it on m68k.  On
most other architectures it just uses get_cycles() (which is typically
inlined and doesn't need exporting),

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Export mach_random_get_entropy to modules
  m68k: Fix boot regression on machines with RAM at non-zero

Merge branch 'parisc-3.16-5' of git://git./linux/kernel/git/deller/parisc-linux

Pull parisc fixes from Helge Deller:
"The major patch in here is one which fixes the fanotify_mark() syscall
  in the compat layer of the 64bit parisc kernel.  It went unnoticed so
  long, because the calling syntax when using a 64bit parameter in a
  32bit syscall is quite complex and even worse, it may be even
  different if you call syscall() or the glibc wrapper.  This patch
  makes the kernel accept the calling convention when called by the
  glibc wrapper.

  The other two patches are trivial and remove unused headers, #includes
  and adds the serial ports of the fastest C8000 workstation to the
  parisc-kernel internal hardware database"

* 'parisc-3.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: drop unused defines and header includes
  parisc: fix fanotify_mark() syscall on 32bit compat kernel
  parisc: add serial ports of C8000/1GHz machine to hardware database

firewire: IEEE 1394 (FireWire) support should depend on HAS_DMA

Commit b3d681a4fc108f9653bbb44e4f4e72db2b8a5734 ("firewire: Use
COMPILE_TEST for build testing") added COMPILE_TEST as an alternative
dependency for the purpose of build testing the firewire core.
However, this bypasses all other implicit dependencies assumed by PCI,
like HAS_DMA.

If NO_DMA=y:

    drivers/built-in.o: In function `fw_iso_buffer_destroy':
    (.text+0x36a096): undefined reference to `dma_unmap_page'
    drivers/built-in.o: In function `fw_iso_buffer_map_dma':
    (.text+0x36a164): undefined reference to `dma_map_page'
    drivers/built-in.o: In function `fw_iso_buffer_map_dma':
    (.text+0x36a172): undefined reference to `dma_mapping_error'
    drivers/built-in.o: In function `sbp2_send_management_orb':
    sbp2.c:(.text+0x36c6b4): undefined reference to `dma_map_single'
    sbp2.c:(.text+0x36c6c8): undefined reference to `dma_mapping_error'
    sbp2.c:(.text+0x36c772): undefined reference to `dma_map_single'
    sbp2.c:(.text+0x36c786): undefined reference to `dma_mapping_error'
    sbp2.c:(.text+0x36c854): undefined reference to `dma_unmap_single'
    sbp2.c:(.text+0x36c872): undefined reference to `dma_unmap_single'
    drivers/built-in.o: In function `sbp2_map_scatterlist':
    sbp2.c:(.text+0x36ccbc): undefined reference to `scsi_dma_map'
    sbp2.c:(.text+0x36cd36): undefined reference to `dma_map_single'
    sbp2.c:(.text+0x36cd4e): undefined reference to `dma_mapping_error'
    sbp2.c:(.text+0x36cd84): undefined reference to `scsi_dma_unmap'
    drivers/built-in.o: In function `sbp2_unmap_scatterlist':
    sbp2.c:(.text+0x36cda6): undefined reference to `scsi_dma_unmap'
    sbp2.c:(.text+0x36cdc6): undefined reference to `dma_unmap_single'
    drivers/built-in.o: In function `complete_command_orb':
    sbp2.c:(.text+0x36d6ac): undefined reference to `dma_unmap_single'
    drivers/built-in.o: In function `sbp2_scsi_queuecommand':
    sbp2.c:(.text+0x36d8e0): undefined reference to `dma_map_single'
    sbp2.c:(.text+0x36d8f6): undefined reference to `dma_mapping_error'

Add an explicit dependency on HAS_DMA to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

clk: spear3xx: Set proper clock parent of uart1/2

The uarts only work when the parent is ras_ahb_clk. The stale 3.5
based ST tree does this in the board file.

Add it to the clk init function. Not pretty, but the mess there is
amazing anyway.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

clk: spear3xx: Use proper control register offset

The control register is at offset 0x10, not 0x0. This is wreckaged
since commit 5df33a62c (SPEAr: Switch to common clock framework).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>

parisc: drop unused defines and header includes

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+

parisc: fix fanotify_mark() syscall on 32bit compat kernel

On parisc we can not use the existing compat implementation for fanotify_mark()
because for the 64bit mask parameter the higher and lower 32bits are ordered
differently than what the compat function expects from big endian
architectures.

Specifically:
It finally turned out, that on hppa we end up with different assignments
of parameters to kernel arguments depending on if we call the glibc
wrapper function
int fanotify_mark (int __fanotify_fd, unsigned int __flags,
uint64_t __mask, int __dfd, const char *__pathname);
or directly calling the syscall manually
syscall(__NR_fanotify_mark, ...)

Reason is, that the syscall() function is implemented as C-function and
because we now have the sysno as first parameter in front of the other
parameters the compiler will unexpectedly add an empty paramenter in
front of the u64 value to ensure the correct calling alignment for 64bit
values.
This means, on hppa you can't simply use syscall() to call the kernel
fanotify_mark() function directly, but you have to use the glibc
function instead.

This patch fixes the kernel in the hppa-arch specifc coding to adjust
the parameters in a way as if userspace calls the glibc wrapper function
fanotify_mark().

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+

parisc: add serial ports of C8000/1GHz machine to hardware database

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 3.13+

Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma

Pull slave-dmaengine fixes from Vinod Koul:
"We have two small fixes.  First one from Daniel to handle 0-length
  packets for usb cppi dma.  Second by Russell for imx-sdam cyclic
  residue reporting"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  Update imx-sdma cyclic handling to report residue
  dma: cppi41: handle 0-length packets

Merge tag 'samsung-fixes-3' of git://git./linux/kernel/git/kgene/linux-samsung into fixes

Merge "Samsung fixes-3 for 3.16" from Kukjin Kim:

Samsung fixes-3 for v3.16
- update the parent for Auudss clock because kernel will be hang
  during late boot if the parent clock is disabled in bootloader.
- enable clk handing in power domain because while power domain
  on/off, its regarding clock source will be reset and it causes
  a problem so need to handle it.
- add mux clocks to be used by power domain for exynos5420-mfc
  during power domain on/off and property in device tree also.
- register cpuidle only for exynos4210 and exynos5250 because a
  system failure will be happened on other exynos SoCs.

* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: EXYNOS: Register cpuidle device only on exynos4210 and 5250
  ARM: dts: Add clock property for mfc_pd in exynos5420
  clk: exynos5420: Add IDs for clocks used in PD mfc
  ARM: EXYNOS: Add support for clock handling in power domain
  ARM: dts: Update the parent for Audss clocks in Exynos5420

Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'usb-3.16-rc5' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
"Here are some small USB fixes, PHY driver fixes (they ended up in this
  tree for lack of somewhere else to put them), and some new USB device
  ids"

* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
  phy: core: Fix error path in phy_create()
  drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
  phy: omap-usb2: fix devm_ioremap_resource error detection code
  phy: sun4i: depend on RESET_CONTROLLER
  USB: serial: ftdi_sio: Add Infineon Triboard
  USB: ftdi_sio: Add extra PID.
  usb: option: Add ID for Telewell TW-LTE 4G v2
  USB: cp210x: add support for Corsair usb dongle

Merge tag 'tty-3.16-rc5' of git://git./linux/kernel/git/gregkh/tty

Pull tty/serial fixes from Greg KH:
"Here are some small serial fixes that resolve some reported problems
  that started in 3.15 with some serial drivers.

  And there's a new dt binding for a serial driver, which was all that
  was needed for the renesas serial driver"

* tag 'tty-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0
  serial: imx: Fix build breakage
  serial: arc_uart: Use uart_circ_empty() for open-coded comparison
  serial: Test for no tx data on tx restart

Merge tag 'char-misc-3.16-rc5' of git://git./linux/kernel/git/gregkh/char-misc

Pull char/misc driver fixes from Greg KH:
"Here are two hyperv driver fixes, and one i8k driver fix for 3.16"

* tag 'char-misc-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  i8k: Fix non-SMP operation
  Drivers: hv: util: Fix a bug in the KVP code
  Drivers: hv: vmbus: Fix a bug in the channel callback dispatch code

Merge tag 'staging-3.16-rc5' of git://git./linux/kernel/git/gregkh/staging

Pull IIO fixes from Greg KH:
"Here are some IIO driver fixes for 3.16-rc5.  Nothing major, just
  resolves some minor issues that have been reported"

* tag 'staging-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: ti_am335x_adc: Fix: Use same step id at FIFOs both ends
  iio:tcs3472: Check for buffer enabled and locking
  iio: hid-sensor-prox: Fix return values
  iio: hid-sensor-gyro-3d: Fix return values
  iio: hid-sensor-als: Fix return values
  iio: hid-sensor-magn-3d: Fix return values
  iio: hid-sensor-accel-3d: Fix return values
  iio: hid-sensor-press: Fix return values

ext4: fix potential null pointer dereference in ext4_free_inode

Fix potential null pointer dereferencing problem caused by e43bb4e612
("ext4: decrement free clusters/inodes counters when block group declared bad")

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>

ext4: fix a potential deadlock in __ext4_es_shrink()

This fixes the following lockdep complaint:

[ INFO: possible circular locking dependency detected ]
3.16.0-rc2-mm1+ #7 Tainted: G           O
-------------------------------------------------------
kworker/u24:0/4356 is trying to acquire lock:
(&(&sbi->s_es_lru_lock)->rlock){+.+.-.}, at: [<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0

but task is already holding lock:
(&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180

which lock already depends on the new lock.

Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&ei->i_es_lock);
                               lock(&(&sbi->s_es_lru_lock)->rlock);
                               lock(&ei->i_es_lock);
  lock(&(&sbi->s_es_lru_lock)->rlock);

*** DEADLOCK ***

6 locks held by kworker/u24:0/4356:
#0:  ("writeback"){.+.+.+}, at: [<ffffffff81071d00>] process_one_work+0x180/0x560
#1:  ((&(&wb->dwork)->work)){+.+.+.}, at: [<ffffffff81071d00>] process_one_work+0x180/0x560
#2:  (&type->s_umount_key#22){++++++}, at: [<ffffffff811a9c74>] grab_super_passive+0x44/0x90
#3:  (jbd2_handle){+.+...}, at: [<ffffffff812979f9>] start_this_handle+0x189/0x5f0
#4:  (&ei->i_data_sem){++++..}, at: [<ffffffff81247062>] ext4_map_blocks+0x132/0x550
#5:  (&ei->i_es_lock){++++-.}, at: [<ffffffff81286961>] ext4_es_insert_extent+0x71/0x180

stack backtrace:
CPU: 0 PID: 4356 Comm: kworker/u24:0 Tainted: G           O   3.16.0-rc2-mm1+ #7
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Workqueue: writeback bdi_writeback_workfn (flush-253:0)
ffffffff8213dce0 ffff880014b07538 ffffffff815df0bb 0000000000000007
ffffffff8213e040 ffff880014b07588 ffffffff815db3dd ffff880014b07568
ffff880014b07610 ffff88003b868930 ffff88003b868908 ffff88003b868930
Call Trace:
[<ffffffff815df0bb>] dump_stack+0x4e/0x68
[<ffffffff815db3dd>] print_circular_bug+0x1fb/0x20c
[<ffffffff810a7a3e>] __lock_acquire+0x163e/0x1d00
[<ffffffff815e89dc>] ? retint_restore_args+0xe/0xe
[<ffffffff815ddc7b>] ? __slab_alloc+0x4a8/0x4ce
[<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
[<ffffffff810a8707>] lock_acquire+0x87/0x120
[<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
[<ffffffff8128592d>] ? ext4_es_free_extent+0x5d/0x70
[<ffffffff815e6f09>] _raw_spin_lock+0x39/0x50
[<ffffffff81285fff>] ? __ext4_es_shrink+0x4f/0x2e0
[<ffffffff8119760b>] ? kmem_cache_alloc+0x18b/0x1a0
[<ffffffff81285fff>] __ext4_es_shrink+0x4f/0x2e0
[<ffffffff812869b8>] ext4_es_insert_extent+0xc8/0x180
[<ffffffff812470f4>] ext4_map_blocks+0x1c4/0x550
[<ffffffff8124c4c4>] ext4_writepages+0x6d4/0xd00
...

Reported-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Minchan Kim <minchan@kernel.org>
Cc: stable@vger.kernel.org
Cc: Zheng Liu <gnehzuil.liu@gmail.com>

Documenation/laptops: rename and update hpfall.c

Dell kernel driver dell-smo8800 provides same freefall interface as hp_accel so
program hpfall.c works also on Dell laptops. So rename it to freefall.c.

Dell driver does not provide hp::hddprotect led so make sure that freefall.c
works also if hp::hddprotect does not exist in sysfs.

Additionally write info to syslog.

Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Sonal Santan <sonal.santan@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

DocBook: fix various typos

This patch fixed spelling typo in various template files
within Documentation/Docbook.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

DocBook: fix mtdnand typos

This patch fixed spelling typo found in DocBook/mtdnand.tmpl.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

scripts/kernel-doc: handle object-like macros

Object-like macros are different than function-like macros:
https://gcc.gnu.org/onlinedocs/cpp/Object-like-Macros.html
https://gcc.gnu.org/onlinedocs/cpp/Function-like-Macros.html

They are not parsed correctly, generating invalid intermediate
files (xmls) for cases like:
#define BIT_MASK (0xFF << BIT_SHIFT)
where "OxFF <<" is considered to be parameter type.

When parsing, we can differentiate beween these two types of macros by
checking whether there is at least one whitespace b/w "#define" and
first opening parenthesis.

Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Documentation/Changes: clean up mcelog paragraph

The paragraph on mcelog currently describes kernel v2.6.31. In that
kernel the mce code (for i386, that is) was in transition. Ever since
v2.6.32 the situation is much simpler (eg, mcelog is now needed to
process events on almost all x86 machines, i386 and x86-64). Since this
"document is designed to provide a list of the minimum levels of
software necessary to run the 3.0 kernels" let's just describe that
situation.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ARM: at91: at91sam9x5: add clocks for usb device

Add clocks for usb device, or else switch to CCF, the gadget
won't work.

Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge branch 'kprobes-test-fixes' of git://git.linaro.org/people/tixy/kernel into fixes

phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove

If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.

This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.

Balance out the pm_runtime_enable() call in .remove() as well.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: core: Fix error path in phy_create()

Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.

Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE

Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: omap-usb2: fix devm_ioremap_resource error detection code

devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.

A simplified version of the semantic match that finds this problem is as
follows:

// <smpl>
@@
expression e,e1;
statement S;
@@

*e = devm_ioremap_resource(...);
if (!e1) S

// </smpl>

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

phy: sun4i: depend on RESET_CONTROLLER

The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: ftdi_sio: Add Infineon Triboard

This adds support for Infineon TriBoard TC1798 [1]. Only interface 1
is used as serial line (see [2], Figure 8-6).

[1] http://www.infineon.com/cms/de/product/microcontroller/development-tools-software-and-kits/tricore-tm-development-tools-software-and-kits/starterkits-and-evaluation-boards/starter-kit-tc1798/channel.html?channel=db3a304333b8a7ca0133cfa3d73e4268
[2] http://www.infineon.com/dgdl/TriBoardManual-TC1798-V10.pdf?folderId=db3a304412b407950112b409ae7c0343&fileId=db3a304333b8a7ca0133cfae99fe426a

Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0

Simply document new compat strings.
There appears to be no need for a driver updates.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: imx: Fix build breakage

Fix breakage introduced by
commit c557d392fbf5badd693ea1946a4317c87a26a716,
'serial: Test for no tx data on tx restart'.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Peter Anvin:
"A couple of further build fixes for the VDSO code.

  This is turning into a bit of a headache, and Andy has already come up
  with a more ultimate cleanup, but most likely that is 3.17 material"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86-32, vdso: Fix vDSO build error due to missing align_vdso_addr()
  x86-64, vdso: Fix vDSO build breakage due to empty .rela.dyn

Merge branch 'for-3.16' of git://linux-nfs.org/~bfields/linux

Pull nfsd bugfix from Bruce Fields:
"Another xdr encoding regression that may cause incorrect encoding on
failures of certain readdirs"

* 'for-3.16' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix bad reserving space for encoding rdattr_error