Sujith Manoharan [Tue, 16 Jul 2013 06:33:21 +0000 (12:03 +0530)]
ath9k: Program correct initvals for FCC
* CUS217 specific initvals have to be programmed.
* iniAdditional is not used for AR9462/AR9565, remove it.
* Handle channel 2484 for regulatory compliance.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 16 Jul 2013 06:33:20 +0000 (12:03 +0530)]
ath9k: Use correct channel when switching bands
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 16 Jul 2013 06:33:19 +0000 (12:03 +0530)]
ath9k: Fix FastChannelChange for AR9462/AR9565
Right now, even though these chips support cross-band
FCC, the code is non-functional since we bail out early if
the channelFlags differ. Fix this so that cross-band
FCC works for cards that support this feature.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 16 Jul 2013 06:33:18 +0000 (12:03 +0530)]
ath9k: Add a HW flag for FCC
Fast Channel Change across 2G/5G bands is supported
only by AR9462 and AR9565. Add a HW capability field
to indicate this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Tue, 16 Jul 2013 06:33:17 +0000 (12:03 +0530)]
ath9k: Move INI overrides to ar9003_hw_override_ini
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John Greene [Mon, 15 Jul 2013 18:33:34 +0000 (14:33 -0400)]
brcmsmac: Further reduce log spam from tx phy messages
Relegate 2 phy messages to debug status as they create excessive
log spam, noted in multiple bugzillas for brcmsmac v3.8 and up.
This is a follow on to net-next
99e94940697adec4f84758adb2db71f4a82c7ba5:
brcmsmac: Reduce log spam in heavy tx, make err print in debug
brcmsmac bcma0:0: phyerr 0x10, rate 0x14
brcmsmac bcma0:0: brcms_c_ampdu_dotxstatus_complete:
ampdu tx phy error (0x10)
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 15 Jul 2013 11:15:08 +0000 (13:15 +0200)]
bcma: fix handling of big addrl
The return value of bcma_erom_get_addr_desc() is a unsigned value and it
could wrap around in the two complement writing. This happens for one
core in the BCM4708 SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 15 Jul 2013 11:15:07 +0000 (13:15 +0200)]
bcma: return correct error code when bus scan failed
It is better to return the actual error code than just -1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 15 Jul 2013 11:15:06 +0000 (13:15 +0200)]
bcma: add constants for new ARM based SoCs
These are the chipIDs of some ARM based SoCs from the BCM47xx line.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 15 Jul 2013 11:15:05 +0000 (13:15 +0200)]
bcma: make it possible to select SoC support without mips
To make it possible to use the SoC host interface with ARM SoCs do not
depend on the MIPS driver any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Mon, 15 Jul 2013 11:15:04 +0000 (13:15 +0200)]
bcma: add some more core names
These cores were found on a BCM4708 (chipid 53010), this is a ARM SoC
with two Cortex A9 cores.
bcma: bus0: Found chip with id 0xCF12, rev 0x00 and package 0x02
bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
bcma: bus0: Core 1 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0)
bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 6 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
bcma: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
bcma: bus0: Core 8 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0)
bcma: bus0: Core 9 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0)
bcma: bus0: Core 10 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0)
bcma: bus0: Core 11 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0)
bcma: bus0: Core 12 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0)
bcma: bus0: Core 13 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0)
bcma: bus0: Core 14 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0)
bcma: bus0: Core 15 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
bcma: bus0: Core 16 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Thu, 11 Jul 2013 15:03:41 +0000 (18:03 +0300)]
wil6210: fix subtle race in wil_tx_vring
Finish all SW context modifications prior to notifying hardware
It used to be race condition: if HW finish Tx and issue Tx completion IRQ very fast,
prior to SW context update in wil_tx_vring, Tx completion will mis-handle descriptor, as
SW part will have no skb pointer stored.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Thu, 11 Jul 2013 15:03:40 +0000 (18:03 +0300)]
wil6210: Introduce struct for sw context
Enable adding more data to the SW context.
For now, add flag "mapped_as_page", to separate decisions on free-ing skb
and type of DMA mapping.
This allows linking skb itself to any descriptor of fragmented skb.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Thu, 11 Jul 2013 15:03:39 +0000 (18:03 +0300)]
wil6210: Optimize Tx completion
No need to modify HW descriptor, as it will be re-initialized on Tx.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Thu, 11 Jul 2013 15:03:38 +0000 (18:03 +0300)]
wil6210: fix wrong index in wil_vring_free
When destroying Rx vring, branch for Rx used wrong Tx descriptor:
while SW context was taken for "head", HW descriptor was, by mistake,
taken from "tail"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev [Thu, 11 Jul 2013 15:03:37 +0000 (18:03 +0300)]
wil6210: Align WMI header with latest FW
FW guys changed header structure; align driver code
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:35 +0000 (16:08 +0200)]
rt2x00: rt2800usb: add USB device ID for Linksys AE3000
The Linksys AE3000 device is based on the RT3573
chipset. The support for this chipset is available
already, and the AE3000 device works with the driver.
Only managed mode works correctly at the moment,
for AP mode additional changes are needed in the
driver.
Also add a new RT2800USB_RT3573 Kconfig option and
only enable support for RT3573 based devices if
that is enabled.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:34 +0000 (16:08 +0200)]
rt2x00: rt2800usb: use correct [RT]XWI size for RT3593
The RT3593 chipset requires different [RT]XWI size
values. Modify the driver to use the correct values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:33 +0000 (16:08 +0200)]
rt2x00: rt2800lib: enable RT3593 support
Support for the RT3593 has been implemented in
the previous changes, so it is safe to mark it
supported in the driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:32 +0000 (16:08 +0200)]
rt2x00: rt2800lib: enable RF3053 support
Support for the RF3053 has been implemented in
the previous changes, so it is safe to mark it
supported in the driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:31 +0000 (16:08 +0200)]
rt2x00: rt2800lib: enable VCO recalibration for RF3053
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:30 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add channel configuration for RF3053
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RT3593_ChipSwitchChannel in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:29 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add rf_vals for RF3053
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
FreqItems3053 in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:28 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add default_power3 field for three-chain devices
The actual code uses two default TX power values.
This is enough for 1T and for 2T devices however
on 3T devices another value is needed for the third
chain.
Add a new field to struct channel_info and initialize
it from the 'rt2800_probe_hw_mode' function. Also modify
the 'rt2800_config_channel' to handle the new field as
well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:27 +0000 (16:08 +0200)]
rt2x00: rt2800lib: fix LNA_A[12] gain values for RT3593
The LNA_A[12] gain values are stored at a different
offset in the EEPROM on RT3593 based devices. However
the current code unconditionally reads those values
from the location used by other chipsets.
Fix the code to use the correct EEPROM offset.
Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
RT3593_EEPROM_RSSI2_OFFSET_ALNAGAIN1_24G_READ in include/chip/rt3593.h
RT3593_EEPROM_RSSI2_OFFSET_ALNAGAIN2_5G_READ in include/chip/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:26 +0000 (16:08 +0200)]
rt2x00: rt2800lib: hardcode TX mixer gain values for RT3593
The reference code uses hardcoded zero TX mixer gain value
for RT3593. Do the same in the rt2x00 driver.
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
NICReadEEPROMParameters in common/rtmp_init.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:25 +0000 (16:08 +0200)]
rt2x00: rt2800lib: introduce rt2800_get_txmixer_gain_{24,5}g helpers
Move the TX mixer gain reading code into separate
helper functions in preparation for RT3593 support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:24 +0000 (16:08 +0200)]
rt2x00: rt2800lib: fix default TX power values for RT3593
The TX power values in the EEPROM are using
a different format for the RT3593 chip. The
default TX power value uses bits 0..4 only.
Bits 5..8 contains value for fine grained
power control. Additionally, the lower and
upper limits of the TX power values are the
same for both bands.
Improve the rt2800_txpower_to_dev function,
in order to compute the correct default power
values for the RT3593 chip as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:23 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add rt2800_txpower_to_dev helper
Introduce a new helper function for converting
the default TX power values from EEPROM into
mac80211 values.
The change improves the readability and it makes
it easier to add support for other chipsets.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:22 +0000 (16:08 +0200)]
rt2x00: rt2800lib: fix antenna configuration for RT3593
On the RT3593 chipset, BBP register 86 must be
configured by different values based on the RX
antenna numbers.
Configure this register from the 'rt2800_config_ant'
function.
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RT3593_CONFIG_SET_BY_ANTENNA in include/chip/rt3593.h
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:21 +0000 (16:08 +0200)]
rt2x00: rt2800lib: fix BBP1_TX_ANTENNA field configuration for 3T devices
The field must be set to 2 instead of 0 for
devices with three TX chains.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:20 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add TX power configuration for RT3593
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
RTMPReadTxPwrPerRateExt in chips/rt3593.c
RT3593_AsicGetTxPowerOffset in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:19 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add BBP post initialization for RT3593
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
RT3593_PostBBPInitialization in chips/rt3553.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:18 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add RFCSR register initialization for RT3593
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
NICInitRT3593RFRegisters in chips/rt3593.c
RT3593LoadRFNormalModeSetup in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:17 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add BBP register initialization for RT3593
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
References:
NICInitRT3593BbpRegisters in chips/rt3593.c
NICInitBBP in common/rtmp_init.c
NICInitAsicFromEEPROM in common/rtmp_init.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 14:08:16 +0000 (16:08 +0200)]
rt2x00: rt2800lib: add MAC register initialization for RT3593
Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Reference:
NICInitRT3593MacRegisters in chips/rt3593.c
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 09:25:56 +0000 (11:25 +0200)]
rt2x00: rt2800lib: add EEPROM map for the RT3593 chipset
Three-chain devices are using a different
EEPROM layout than the rest of the chipsets.
Add a new map which describes the new layout
and use that for the RT3593 chipset.
The index values has been computed from the
EEPROM_EXT_* defines, which can be found in
the 'include/chip/rt3593.h' file in the
Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 09:25:55 +0000 (11:25 +0200)]
rt2x00: rt2800lib: introduce rt2800_eeprom_word_index helper
Instead of assign the offset value to the
enum directly use a new helper function to
convert a rt2800_eeprom_word enum into an
index of the rt2x00_dev->eeprom array.
The patch does not change the existing
behaviour, but makes it possible to add
support for three-chain devices which are
using a different EEPROM layout.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 09:25:54 +0000 (11:25 +0200)]
rt2x00: rt2800lib: introduce rt2800_eeprom_read_from_array helper
Add a new helper function and use that for reading
single elements of various arrays in the EEPROM.
The patch does not change the current behaviour,
but it allows to use sequential values for the
rt2800_eeprom_word enums. The conversion will be
implemented in a subsequent change.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 09:25:53 +0000 (11:25 +0200)]
rt2x00: rt2800lib: introduce local EEPROM access functions
The patch adds rt2800 specific functions for
EEPROM data access and changes the code to use
these instead of the generic rt2x00_eeprom_*
variants.
To avoid functional changes, the new functions
are wrappers around the corresponding generic
rt2x00_eeprom_* routines for now. Functional
changes will be implemented in additional patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Mon, 8 Jul 2013 09:25:52 +0000 (11:25 +0200)]
rt2x00: rt2800lib: introduce rt2800_eeprom_word enum
The patch converts the EEPROM_* word address defines
into new enum values. The new enum type will be used
by new functions which will be introduced in subsequent
changes.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Thu, 4 Jul 2013 07:29:47 +0000 (12:59 +0530)]
ath9k: Fix RTS threshold
Currently, RTS threshold is not handled for HT. Handle
user-specified threshold values for both aggregated
and unaggregated frames. Use the wiphy's threshold
parameter for now, it can be made per-VIF later on.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 3 Jul 2013 18:55:38 +0000 (20:55 +0200)]
ath9k: make rfkill configurable
When the platform doesn't have rfkill support, i.e. nothing
is connected to the rfkill GPIO, there's little value in
polling the GPIO. Add a Kconfig option to allow disabling
the polling in ath9k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shuah Khan [Wed, 3 Jul 2013 16:47:10 +0000 (10:47 -0600)]
wireless: Convert mwifiex/pcie to dev_pm_ops from legacy pm_ops
Convert the mwifiex/pci driver to use dev_pm_ops for power management and
remove Legacy PM handling. This change re-uses existing suspend and resume
interfaces for dev_pm_ops, and changes CONFIG_PM ifdefs to CONFIG_PM_SLEEP
as the driver does not support run-time PM.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Jul 2013 10:46:24 +0000 (12:46 +0200)]
brcmfmac: bail out of brcmf_txflowblock_if() for non-netdev interface
To avoid ending up in a NULL-pointer access, the function
brcmf_txflowblock_if() should only be called for interfaces
that have a netdev associated with it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Jul 2013 18:31:22 +0000 (20:31 +0200)]
brcmfmac: decrement pending 8021x count upon tx failure
If the transmit fails because there are no hanger slots or
any other reason and the packet was an EAPOL packet the
pending counter should be decreased although it was not
transmitted so the driver does not end up in a dead-lock.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sun, 21 Jul 2013 02:46:48 +0000 (21:46 -0500)]
ath: wil6210: Fix build error
Building driver wil6210 in 3.10 and 3.11 kernels yields the following errors:
CC [M] drivers/net/wireless/ath/wil6210/debugfs.o
drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_print_ring':
drivers/net/wireless/ath/wil6210/debugfs.c:163:11: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign]
false);
^
In file included from include/linux/kernel.h:13:0,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *'
extern void hex_dump_to_buffer(const void *buf, size_t len,
^
drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_txdesc_debugfs_show':
drivers/net/wireless/ath/wil6210/debugfs.c:429:10: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign]
sizeof(printbuf), false);
^
In file included from include/linux/kernel.h:13:0,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *'
extern void hex_dump_to_buffer(const void *buf, size_t len,
^
cc1: all warnings being treated as errors
make[5]: *** [drivers/net/wireless/ath/wil6210/debugfs.o] Error 1
make[4]: *** [drivers/net/wireless/ath/wil6210] Error 2
make[3]: *** [drivers/net/wireless/ath] Error 2
make[2]: *** [drivers/net/wireless] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
These errors are fixed by changing the type of the buffer from "unsigned char *" to "char *".
Reported-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Tested-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.10]
Cc: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Solomon Peachy [Sat, 20 Jul 2013 03:31:27 +0000 (23:31 -0400)]
cw1200: Fix OOPS in monitor mode
In monitor mode, priv->vif is NULL, but at one point in the receive path we
blindly attempt to dereference it. Add a test to prevent this.
Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oleksij Rempel [Fri, 19 Jul 2013 18:16:18 +0000 (20:16 +0200)]
ath9k_htc: reboot firmware if it was loaded
Currently ath9k_htc will reboot firmware only if interface was
ever started. Which lead to the problem in case where interface
was never started but module need to be reloaded.
This patch will partially fix bug "ath9k_htc: Target is unresponsive"
https://github.com/qca/open-ath9k-htc-firmware/issues/1
Reproduction case:
- plug adapter
- make sure nothing will touch it. Stop Networkmanager or blacklist mac address of this adapter.
- rmmod ath9k_htc; sleep 1; modprobe ath9k_htc
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oleksij Rempel [Fri, 19 Jul 2013 18:16:17 +0000 (20:16 +0200)]
ath9k_htc: do some initial hardware configuration
Currently we configure harwdare and clock, only after
interface start. In this case, if we reload module or
reboot PC without configuring adapter, firmware will freeze.
There is no software way to reset adpter.
This patch add initial configuration and set it in
disabled state, to avoid this freeze. Behaviour of this patch
should be similar to: ifconfig wlan0 up; ifconfig wlan0 down.
Bug: https://github.com/qca/open-ath9k-htc-firmware/issues/1
Tested-by: Bo Shi <cnshibo@gmail.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Sat, 13 Jul 2013 14:57:10 +0000 (10:57 -0400)]
mwifiex: fix IRQ enable/disable
During tear down (e.g. mwifiex_sdio_remove during system suspend),
mwifiex left IRQs enabled for a significant period of time when it was
unable to handle them correctly. This caused interrupt storms and
interfered with the bluetooth interface on the same SDIO card.
Solve this by disabling interrupts at the point when they can no longer
be handled correctly, which is at the start of mwifiex_remove_card().
For cleanliness, we now enable interrupts in the mwifiex_add_card() path,
to be symmetrical with the disabling of interrupts. We also couple the
registration of the sdio IRQ handler with the actual enable/disable of
interrupts at the hardware level.
I also removed a write to this register in mwifiex_init_sdio which seemed
pointless and won't cause any ill effects now that we only register
the SDIO IRQ handler when we are ready to accept interrupts.
Includes some corrections from Amitkumar Karwar.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 22 Jul 2013 20:02:10 +0000 (16:02 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-fixes
John W. Linville [Mon, 22 Jul 2013 20:00:49 +0000 (16:00 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211
Sujith Manoharan [Mon, 15 Jul 2013 05:33:57 +0000 (11:03 +0530)]
ath9k_hw: Fix multicast search for AR9002 family
The multicast search bit is disabled for the AR9003
family, but this is required for AR9002 too. Fix this in
the INI override routine.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 12 Jul 2013 20:32:15 +0000 (15:32 -0500)]
rtlwifi: Fix build errors for unusual cases
The present build configuration for the rtlwifi family of drivers will
fail under two known conditions:
(1) If rtlwifi is selected without selecting any of the dependent drivers,
there are errors in the build.
(2) If the PCI drivers are built into the kernel and the USB drivers are modules,
or vice versa, there are missing globals.
The first condition is fixed by never building rtlwifi unless at least one
of the device drivers is selected. The second failure is fixed by splitting
the PCI and USB codes out of rtlwifi, and creating their own mini drivers.
If the drivers that use them are modules, they will also be modules.
Although a number of files are touched by this patch, only Makefile and Kconfig
have undergone significant changes. The only modifications to the other files
were to export entry points needed by the new rtl_pci and rtl_usb units, or to
rename two variables that had names that were likely to cause namespace collisions.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [Condition 1]
Reported-by: Ben Hutchings <bhutchings@solarflare.com> [Condition 2]
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Thu, 11 Jul 2013 13:19:13 +0000 (09:19 -0400)]
ath5k: fix extra set bit in multicast mask
Bit 32 was always set which looks to have been accidental,
according to git history.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Geert Uytterhoeven [Wed, 10 Jul 2013 21:03:35 +0000 (23:03 +0200)]
rt2x00: RT2X00 should depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `rt2x00queue_unmap_skb':
drivers/net/wireless/rt2x00/rt2x00queue.c:129: undefined reference to `dma_unmap_single'
drivers/net/wireless/rt2x00/rt2x00queue.c:133: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `rt2x00queue_map_txskb':
drivers/net/wireless/rt2x00/rt2x00queue.c:112: undefined reference to `dma_map_single'
drivers/net/wireless/rt2x00/rt2x00queue.c:115: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `rt2x00queue_alloc_rxskb':
drivers/net/wireless/rt2x00/rt2x00queue.c:93: undefined reference to `dma_map_single'
drivers/net/wireless/rt2x00/rt2x00queue.c:95: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arnd Bergmann [Fri, 5 Jul 2013 15:43:56 +0000 (17:43 +0200)]
ssb: fix alignment of struct bcma_device_id
The ARM OABI and EABI disagree on the alignment of structures
with small members, so module init tools may interpret the
ssb device table incorrectly, as shown by this warning when
building the b43 device driver in an OABI kernel:
FATAL: drivers/net/wireless/b43/b43: sizeof(struct ssb_device_id)=6 is
not a modulo of the size of section __mod_ssb_device_table=88.
Forcing the default (EABI) alignment on the structure makes this
problem go away. Since the ssb_device_id may have the same problem,
better fix both structures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexey Khoroshilov [Mon, 1 Jul 2013 20:43:42 +0000 (00:43 +0400)]
ath9k_htc: fix data race between request_firmware_nowait() callback and suspend()
ath9k_hif_usb_probe() requests firmware asynchronically and
there is some initialization postponed till firmware is ready.
In particular, ath9k_hif_usb_firmware_cb() callback initializes
hif_dev->tx.tx_buf and hif_dev->tx.tx_pending lists.
At the same time, ath9k_hif_usb_suspend() iterates that lists through
ath9k_hif_usb_dealloc_urbs(). If suspend happens before request_firmware_nowait()
callback is called, it can lead to oops.
Similar issue could be in ath9k_hif_usb_disconnect(), but it is prevented
using hif_dev->fw_done completion and HIF_USB_READY flag. The patch extends
this approach to suspend() as well.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 30 Jun 2013 10:02:13 +0000 (12:02 +0200)]
ath9k: fix tx pending frames accounting for dropped packets
When dropping packets that have gone far enough into the tx path, the
pending frame counter needs to be decreased.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 28 Jun 2013 14:12:53 +0000 (09:12 -0500)]
rtlwifi: Initialize power-setting callback for USB devices
Commit
a269913c5 entitled "rtlwifi: Rework rtl_lps_leave() and
rtl_lps_enter() to use work queue" has two bugs for USB drivers.
Firstly, the work queue in question was not initialized. Secondly,
the callback routine used by this queue is contained within the
file used for PCI devices. As a result, it is not available for
architectures without PCI hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Stable <stable@vger.kernel.org> [3.10]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 15 Jul 2013 12:35:06 +0000 (14:35 +0200)]
mac80211/minstrel: fix NULL pointer dereference issue
When priv_sta == NULL, mi->prev_sample is dereferenced too early. Move
the assignment further down, after the rate_control_send_low call.
Reported-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David Spinadel [Thu, 4 Jul 2013 12:22:26 +0000 (15:22 +0300)]
iwlwifi: mvm: remove extra SSID from probe request
Bits 1-21 in this channel type attributes are indication for which
SSID is going to be sent on this channel. Since the first SSID is
sent implicitly in the probe request, we don't need to toggle its
bit here.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David Spinadel [Thu, 4 Jul 2013 12:17:48 +0000 (15:17 +0300)]
iwlwifi: mvm: fix bug in scan ssid
Increment index in each iteration. Without this increment we are
overriding the added SSIDs and we will send only the last SSId
and (n_ssids - 1) broadcast probes.
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 4 Jul 2013 13:55:29 +0000 (15:55 +0200)]
iwlwifi: mvm: refuse connection to APs with BI < 16
Due to a firmware bug, it crashes when the beacon interval
is smaller than 16. Avoid this by refusing the station state
change creating the AP station, causing mac80211 to abandon
the attempt to connect to the AP, and eventually wpa_s to
blacklist it.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Tue, 2 Jul 2013 11:16:38 +0000 (14:16 +0300)]
iwlwifi: mvm: track the number of Rx BA sessions
The firmware / HW can't support more than 16 Rx BA sessions.
Deny any attemps to open more sessions than that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Emmanuel Grumbach [Tue, 2 Jul 2013 10:35:35 +0000 (13:35 +0300)]
iwlwifi: mvm: fix L2P BA ressources leak
We didn't release the Rx AMPDU ressources properly.
This bug led to firmware assert after 16 BA sessions.
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Alexander Bondar [Sun, 23 Jun 2013 17:31:07 +0000 (20:31 +0300)]
iwlwifi: mvm: Fix VIF specific debugfs directory creation
Avoid creating VIF specific debugfs directory if already exist.
This may happen when, for example, resetting hw, suspend-resume.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Johannes Berg [Fri, 3 May 2013 16:58:16 +0000 (18:58 +0200)]
iwlwifi: dvm: don't send BT_CONFIG on devices w/o Bluetooth
The BT_CONFIG command that is sent to the device during
startup will enable BT coex unless the module parameter
turns it off, but on devices without Bluetooth this may
cause problems, as reported in Redhat BZ 885407.
Fix this by sending the BT_CONFIG command only when the
device has Bluetooth.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Emmanuel Grumbach [Mon, 24 Jun 2013 12:44:03 +0000 (15:44 +0300)]
iwlwifi: mvm: unregister leds when registration failed
This was missing and prevented any further attempts
to load the module.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Johannes Berg [Thu, 11 Jul 2013 20:33:26 +0000 (22:33 +0200)]
mac80211: fix duplicate retransmission detection
The duplicate retransmission detection code in mac80211
erroneously attempts to do the check for every frame,
even frames that don't have a sequence control field or
that don't use it (QoS-Null frames.)
This is problematic because it causes the code to access
data beyond the end of the SKB and depending on the data
there will drop packets erroneously.
Correct the code to not do duplicate detection for such
frames.
I found this error while testing AP powersave, it lead
to retransmitted PS-Poll frames being dropped entirely
as the data beyond the end of the SKB was always zero.
Cc: stable@vger.kernel.org [all versions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chun-Yeow Yeoh [Thu, 11 Jul 2013 10:24:03 +0000 (18:24 +0800)]
nl80211: fix the setting of RSSI threshold value for mesh
RSSI threshold value used for mesh peering should be in
negative value. After range checks to mesh parameters is
introduced, this is not allowed. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Johannes Berg [Mon, 8 Jul 2013 08:43:31 +0000 (10:43 +0200)]
mac80211: fix ethtool stats for non-station interfaces
As reported in https://bugzilla.kernel.org/show_bug.cgi?id=60514,
the station loop never initialises 'sinfo' and therefore adds up
a stack values, leaking stack information (the number of times it
adds values is easily obtained another way.)
Fix this by initialising the sinfo for each station to add.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Felix Fietkau [Fri, 28 Jun 2013 19:04:35 +0000 (21:04 +0200)]
mac80211/minstrel_ht: fix cck rate sampling
The CCK group needs special treatment to set the right flags and rate
index. Add this missing check to prevent setting broken rates for tx
packets.
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Johannes Berg [Mon, 24 Jun 2013 13:43:38 +0000 (15:43 +0200)]
regulatory: add missing rtnl locking
restore_regulatory_settings() requires the RTNL to be held,
add the missing locking in reg_timeout_work().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 28 Jun 2013 09:38:54 +0000 (11:38 +0200)]
cfg80211: fix bugs in new SME implementation
When splitting the SME implementation from the MLME code,
I introduced a few bugs:
* association failures no longer sent a connect-failure event
* getting disassociated from the AP caused deauth to be sent
but state wasn't cleaned up, leading to warnings
* authentication failures weren't cleaned up properly, causing
new connection attempts to warn and fail
Fix these bugs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Michal Kazior [Tue, 25 Jun 2013 07:17:17 +0000 (09:17 +0200)]
nl80211: fix mgmt tx status and testmode reporting for netns
These two events were sent to the default network
namespace.
This caused AP mode in a non-default netns to not
work correctly. Mgmt tx status was multicasted to
a different (default) netns instead of the one the
AP was in.
Cc: stable@vger.kernel.org
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Torvalds [Sun, 14 Jul 2013 22:18:27 +0000 (15:18 -0700)]
Linux 3.11-rc1
Linus Torvalds [Sun, 14 Jul 2013 22:14:29 +0000 (15:14 -0700)]
Merge branch 'slab/for-linus' of git://git./linux/kernel/git/penberg/linux
Pull slab update from Pekka Enberg:
"Highlights:
- Fix for boot-time problems on some architectures due to
init_lock_keys() not respecting kmalloc_caches boundaries
(Christoph Lameter)
- CONFIG_SLUB_CPU_PARTIAL requested by RT folks (Joonsoo Kim)
- Fix for excessive slab freelist draining (Wanpeng Li)
- SLUB and SLOB cleanups and fixes (various people)"
I ended up editing the branch, and this avoids two commits at the end
that were immediately reverted, and I instead just applied the oneliner
fix in between myself.
* 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
slub: Check for page NULL before doing the node_match check
mm/slab: Give s_next and s_stop slab-specific names
slob: Check for NULL pointer before calling ctor()
slub: Make cpu partial slab support configurable
slab: add kmalloc() to kernel API documentation
slab: fix init_lock_keys
slob: use DIV_ROUND_UP where possible
slub: do not put a slab to cpu partial list when cpu_partial is 0
mm/slub: Use node_nr_slabs and node_nr_objs in get_slabinfo
mm/slub: Drop unnecessary nr_partials
mm/slab: Fix /proc/slabinfo unwriteable for slab
mm/slab: Sharing s_next and s_stop between slab and slub
mm/slab: Fix drain freelist excessively
slob: Rework #ifdeffery in slab.h
mm, slab: moved kmem_cache_alloc_node comment to correct place
Steven Rostedt [Thu, 17 Jan 2013 18:10:58 +0000 (13:10 -0500)]
slub: Check for page NULL before doing the node_match check
In the -rt kernel (mrg), we hit the following dump:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<
ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
PGD
a2d39067 PUD
b1641067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: sunrpc cpufreq_ondemand ipv6 tg3 joydev sg serio_raw pcspkr k8temp amd64_edac_mod edac_core i2c_piix4 e100 mii shpchp ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom sata_svw ata_generic pata_acpi pata_serverworks radeon ttm drm_kms_helper drm hwmon i2c_algo_bit i2c_core dm_mirror dm_region_hash dm_log dm_mod
CPU 3
Pid: 20878, comm: hackbench Not tainted 3.6.11-rt25.14.el6rt.x86_64 #1 empty empty/Tyan Transport GT24-B3992
RIP: 0010:[<
ffffffff811573f1>] [<
ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
RSP: 0018:
ffff8800a9b17d70 EFLAGS:
00010213
RAX:
0000000000000000 RBX:
0000000001200011 RCX:
ffff8800a06d8000
RDX:
0000000004d92a03 RSI:
00000000000000d0 RDI:
ffff88013b805500
RBP:
ffff8800a9b17dc0 R08:
ffff88023fd14d10 R09:
ffffffff81041cbd
R10:
00007f4e3f06e9d0 R11:
0000000000000246 R12:
ffff88013b805500
R13:
ffff8801ff46af40 R14:
0000000000000001 R15:
0000000000000000
FS:
00007f4e3f06e700(0000) GS:
ffff88023fd00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
CR2:
0000000000000000 CR3:
00000000a2d3a000 CR4:
00000000000007e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
Process hackbench (pid: 20878, threadinfo
ffff8800a9b16000, task
ffff8800a06d8000)
Stack:
ffff8800a9b17da0 ffffffff81202e08 ffff8800a9b17de0 000000d001200011
0000000001200011 0000000001200011 0000000000000000 0000000000000000
00007f4e3f06e9d0 0000000000000000 ffff8800a9b17e60 ffffffff81041cbd
Call Trace:
[<
ffffffff81202e08>] ? current_has_perm+0x68/0x80
[<
ffffffff81041cbd>] copy_process+0xdd/0x15b0
[<
ffffffff810a2125>] ? rt_up_read+0x25/0x30
[<
ffffffff8104369a>] do_fork+0x5a/0x360
[<
ffffffff8107c66b>] ? migrate_enable+0xeb/0x220
[<
ffffffff8100b068>] sys_clone+0x28/0x30
[<
ffffffff81527423>] stub_clone+0x13/0x20
[<
ffffffff81527152>] ? system_call_fastpath+0x16/0x1b
Code: 89 fc 89 75 cc 41 89 d6 4d 8b 04 24 65 4c 03 04 25 48 ae 00 00 49 8b 50 08 4d 8b 28 49 8b 40 10 4d 85 ed 74 12 41 83 fe ff 74 27 <48> 8b 00 48 c1 e8 3a 41 39 c6 74 1b 8b 75 cc 4c 89 c9 44 89 f2
RIP [<
ffffffff811573f1>] kmem_cache_alloc_node+0x51/0x180
RSP <
ffff8800a9b17d70>
CR2:
0000000000000000
---[ end trace
0000000000000002 ]---
Now, this uses SLUB pretty much unmodified, but as it is the -rt kernel
with CONFIG_PREEMPT_RT set, spinlocks are mutexes, although they do
disable migration. But the SLUB code is relatively lockless, and the
spin_locks there are raw_spin_locks (not converted to mutexes), thus I
believe this bug can happen in mainline without -rt features. The -rt
patch is just good at triggering mainline bugs ;-)
Anyway, looking at where this crashed, it seems that the page variable
can be NULL when passed to the node_match() function (which does not
check if it is NULL). When this happens we get the above panic.
As page is only used in slab_alloc() to check if the node matches, if
it's NULL I'm assuming that we can say it doesn't and call the
__slab_alloc() code. Is this a correct assumption?
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 14 Jul 2013 18:42:26 +0000 (11:42 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull more vfs stuff from Al Viro:
"O_TMPFILE ABI changes, Oleg's fput() series, misc cleanups, including
making simple_lookup() usable for filesystems with non-NULL s_d_op,
which allows us to get rid of quite a bit of ugliness"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
sunrpc: now we can just set ->s_d_op
cgroup: we can use simple_lookup() now
efivarfs: we can use simple_lookup() now
make simple_lookup() usable for filesystems that set ->s_d_op
configfs: don't open-code d_alloc_name()
__rpc_lookup_create_exclusive: pass string instead of qstr
rpc_create_*_dir: don't bother with qstr
llist: llist_add() can use llist_add_batch()
llist: fix/simplify llist_add() and llist_add_batch()
fput: turn "list_head delayed_fput_list" into llist_head
fs/file_table.c:fput(): add comment
Safer ABI for O_TMPFILE
Al Viro [Sun, 14 Jul 2013 13:55:39 +0000 (17:55 +0400)]
sunrpc: now we can just set ->s_d_op
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 14 Jul 2013 13:50:23 +0000 (17:50 +0400)]
cgroup: we can use simple_lookup() now
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 14 Jul 2013 13:48:35 +0000 (17:48 +0400)]
efivarfs: we can use simple_lookup() now
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 14 Jul 2013 13:43:25 +0000 (17:43 +0400)]
make simple_lookup() usable for filesystems that set ->s_d_op
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 14 Jul 2013 13:16:52 +0000 (17:16 +0400)]
configfs: don't open-code d_alloc_name()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 14 Jul 2013 13:09:57 +0000 (17:09 +0400)]
__rpc_lookup_create_exclusive: pass string instead of qstr
... and use d_hash_and_lookup() instead of open-coding it, for fsck sake...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 14 Jul 2013 12:43:54 +0000 (16:43 +0400)]
rpc_create_*_dir: don't bother with qstr
just pass the name
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sun, 14 Jul 2013 01:08:23 +0000 (18:08 -0700)]
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"Nothing overly exciting here - a couple of new drivers that don't do a
great deal, along with some miscellaneous fixes and a couple of small
feature enablement patches"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
x86 platform drivers: fix gpio leak
toshiba_acpi: Add dependency on SERIO_I8042
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. 1015E/U
Add trivial driver to disable Intel Smart Connect
Add support driver for Intel Rapid Start Technology
hp-wmi: add supports for POST code error
asus-wmi: control wlan-led only if wapf == 4
drivers/platform/x86/intel_ips: Convert to module_pci_driver
asus-nb-wmi: ignore ALS notification key code
asus-wmi: append newline to messages
x86: asus-laptop: fix invalid point access
x86: msi-laptop: fix memleak
amilo-rfkill: Add dependency on SERIO_I8042
dell-laptop: fix error return code in dell_init()
hp-wmi: Enable hotkeys on some systems
Linus Torvalds [Sun, 14 Jul 2013 01:05:13 +0000 (18:05 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull second round of input updates from Dmitry Torokhov:
"An update to Elantech driver to support hardware v7, fix to the new
cyttsp4 driver to use proper addressing, ads7846 device tree support
and nspire-keypad got a small cleanup."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: nspire-keypad - replace magic offset with define
Input: elantech - fix for newer hardware versions (v7)
Input: cyttsp4 - use 16bit address for I2C/SPI communication
Input: ads7846 - add device tree bindings
Input: ads7846 - make sure we do not change platform data
Linus Torvalds [Sun, 14 Jul 2013 00:42:22 +0000 (17:42 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Linus Torvalds [Sun, 14 Jul 2013 00:41:21 +0000 (17:41 -0700)]
Merge tag 'scsi-for-linus' of git://git./linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"This is the remaining set of SCSI patches for the merge window. It's
mostly driver updates (scsi_debug, qla2xxx, storvsc, mp3sas). There
are also several bug fixes in fcoe, libfc, and megaraid_sas. We also
have a couple of core changes to try to make device destruction more
deterministic"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (46 commits)
[SCSI] scsi constants: command, sense key + additional sense strings
fcoe: Reduce number of sparse warnings
fcoe: Stop fc_rport_priv structure leak
libfcoe: Fix meaningless log statement
libfc: Differentiate echange timer cancellation debug statements
libfc: Remove extra space in fc_exch_timer_cancel definition
fcoe: fix the link error status block sparse warnings
fcoe: Fix smatch warning in fcoe_fdmi_info function
libfc: Reject PLOGI from nodes with incompatible role
[SCSI] enable destruction of blocked devices which fail LUN scanning
[SCSI] Fix race between starved list and device removal
[SCSI] megaraid_sas: fix a bug for 64 bit arches
[SCSI] scsi_debug: reduce duplication between prot_verify_read and prot_verify_write
[SCSI] scsi_debug: simplify offset calculation for dif_storep
[SCSI] scsi_debug: invalidate protection info for unmapped region
[SCSI] scsi_debug: fix NULL pointer dereference with parameters dif=0 dix=1
[SCSI] scsi_debug: fix incorrectly nested kmap_atomic()
[SCSI] scsi_debug: fix invalid address passed to kunmap_atomic()
[SCSI] mpt3sas: Bump driver version to v02.100.00.00
[SCSI] mpt3sas: when async scanning is enabled then while scanning, devices are removed but their transport layer entries are not removed
...
Linus Torvalds [Sat, 13 Jul 2013 22:37:57 +0000 (15:37 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"Fix a potential deadlock versus hrtimers"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix HRTICK
Linus Torvalds [Sat, 13 Jul 2013 22:37:30 +0000 (15:37 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
- core fix for missing round up in the generic irq chip implementation
- new irq chip for MOXA SoCs
- a few fixes and cleanups in the irqchip drivers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Add support for MOXA ART SoCs
genirq: generic chip: Use DIV_ROUND_UP to calculate numchips
irqchip: nvic: Fix wrong num_ct argument for irq_alloc_domain_generic_chips()
irqchip: sun4i: Staticize sun4i_irq_ack()
irqchip: vt8500: Staticize local symbols
Linus Torvalds [Sat, 13 Jul 2013 22:36:09 +0000 (15:36 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
- watchdog fixes for full dynticks
- improved debug output for full dynticks
- remove an obsolete full dynticks check
- two ARM SoC clocksource drivers for sharing across SoCs
- tick broadcast fix for CPU hotplug
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: broadcast: Check broadcast mode on CPU hotplug
clocksource: arm_global_timer: Add ARM global timer support
clocksource: Add Marvell Orion SoC timer
nohz: Remove obsolete check for full dynticks CPUs to be RCU nocbs
watchdog: Boot-disable by default on full dynticks
watchdog: Rename confusing state variable
watchdog: Register / unregister watchdog kthreads on sysctl control
nohz: Warn if the machine can not perform nohz_full
Linus Torvalds [Sat, 13 Jul 2013 22:35:47 +0000 (15:35 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
- fix for do_div() abuse on x86
- locking fix in perf core
- a pile of (build) fixes and cleanups in perf tools
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf/x86: Fix incorrect use of do_div() in NMI warning
perf: Fix perf_lock_task_context() vs RCU
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
perf: Clone child context from parent context pmu
perf script: Fix broken include in Context.xs
perf tools: Fix -ldw/-lelf link test when static linking
perf tools: Revert regression in configuration of Python support
perf tools: Fix perf version generation
perf stat: Fix per-socket output bug for uncore events
perf symbols: Fix vdso list searching
perf evsel: Fix missing increment in sample parsing
perf tools: Update symbol_conf.nr_events when processing attribute events
perf tools: Fix new_term() missing free on error path
perf tools: Fix parse_events_terms() segfault on error path
perf evsel: Fix count parameter to read call in event_format__new
perf tools: fix a typo of a Power7 event name
perf tools: Fix -x/--exclude-other option for report command
perf evlist: Enhance perf_evlist__start_workload()
perf record: Remove -f/--force option
perf record: Remove -A/--append option
...
Linus Torvalds [Sat, 13 Jul 2013 22:35:12 +0000 (15:35 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core locking updates from Thomas Gleixner:
"Header cleanup as requested by Linus"
(This is the "don't include support for ww_mutex in a header file that
everybody wants, when almost nobody wants the ww part" change)
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Move ww_mutex definitions to ww_mutex.h
Linus Torvalds [Sat, 13 Jul 2013 22:00:26 +0000 (15:00 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
Linus Torvalds [Sat, 13 Jul 2013 21:58:36 +0000 (14:58 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"A few fixes for ARM, mostly just one liners with the exception of the
missing section specification. We decided not to rely on .previous to
fix this but to explicitly state the section we want the code to be
in."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7778/1: smp_twd: twd_update_frequency need be run on all online CPUs
ARM: 7782/1: Kconfig: Let ARM_ERRATA_364296 not depend on CONFIG_SMP
ARM: mm: fix boot on SA1110 Assabet
ARM: 7781/1: mmu: Add debug_ll_io_init() mappings to early mappings
ARM: 7780/1: add missing linker section markup to head-common.S
Linus Torvalds [Sat, 13 Jul 2013 21:52:21 +0000 (14:52 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...