Merge branch 'parisc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller...
[cascardo/linux.git] / drivers / gpio / gpio-adp5588.c
1 /*
2  * GPIO Chip driver for Analog Devices
3  * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller
4  *
5  * Copyright 2009-2010 Analog Devices Inc.
6  *
7  * Licensed under the GPL-2 or later.
8  */
9
10 #include <linux/module.h>
11 #include <linux/kernel.h>
12 #include <linux/slab.h>
13 #include <linux/init.h>
14 #include <linux/i2c.h>
15 #include <linux/gpio.h>
16 #include <linux/interrupt.h>
17 #include <linux/irq.h>
18
19 #include <linux/i2c/adp5588.h>
20
21 #define DRV_NAME        "adp5588-gpio"
22
23 /*
24  * Early pre 4.0 Silicon required to delay readout by at least 25ms,
25  * since the Event Counter Register updated 25ms after the interrupt
26  * asserted.
27  */
28 #define WA_DELAYED_READOUT_REVID(rev)   ((rev) < 4)
29
30 struct adp5588_gpio {
31         struct i2c_client *client;
32         struct gpio_chip gpio_chip;
33         struct mutex lock;      /* protect cached dir, dat_out */
34         /* protect serialized access to the interrupt controller bus */
35         struct mutex irq_lock;
36         unsigned gpio_start;
37         unsigned irq_base;
38         uint8_t dat_out[3];
39         uint8_t dir[3];
40         uint8_t int_lvl[3];
41         uint8_t int_en[3];
42         uint8_t irq_mask[3];
43         uint8_t irq_stat[3];
44 };
45
46 static int adp5588_gpio_read(struct i2c_client *client, u8 reg)
47 {
48         int ret = i2c_smbus_read_byte_data(client, reg);
49
50         if (ret < 0)
51                 dev_err(&client->dev, "Read Error\n");
52
53         return ret;
54 }
55
56 static int adp5588_gpio_write(struct i2c_client *client, u8 reg, u8 val)
57 {
58         int ret = i2c_smbus_write_byte_data(client, reg, val);
59
60         if (ret < 0)
61                 dev_err(&client->dev, "Write Error\n");
62
63         return ret;
64 }
65
66 static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off)
67 {
68         struct adp5588_gpio *dev = gpiochip_get_data(chip);
69         unsigned bank = ADP5588_BANK(off);
70         unsigned bit = ADP5588_BIT(off);
71         int val;
72
73         mutex_lock(&dev->lock);
74
75         if (dev->dir[bank] & bit)
76                 val = dev->dat_out[bank];
77         else
78                 val = adp5588_gpio_read(dev->client, GPIO_DAT_STAT1 + bank);
79
80         mutex_unlock(&dev->lock);
81
82         return !!(val & bit);
83 }
84
85 static void adp5588_gpio_set_value(struct gpio_chip *chip,
86                                    unsigned off, int val)
87 {
88         unsigned bank, bit;
89         struct adp5588_gpio *dev = gpiochip_get_data(chip);
90
91         bank = ADP5588_BANK(off);
92         bit = ADP5588_BIT(off);
93
94         mutex_lock(&dev->lock);
95         if (val)
96                 dev->dat_out[bank] |= bit;
97         else
98                 dev->dat_out[bank] &= ~bit;
99
100         adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank,
101                            dev->dat_out[bank]);
102         mutex_unlock(&dev->lock);
103 }
104
105 static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off)
106 {
107         int ret;
108         unsigned bank;
109         struct adp5588_gpio *dev = gpiochip_get_data(chip);
110
111         bank = ADP5588_BANK(off);
112
113         mutex_lock(&dev->lock);
114         dev->dir[bank] &= ~ADP5588_BIT(off);
115         ret = adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, dev->dir[bank]);
116         mutex_unlock(&dev->lock);
117
118         return ret;
119 }
120
121 static int adp5588_gpio_direction_output(struct gpio_chip *chip,
122                                          unsigned off, int val)
123 {
124         int ret;
125         unsigned bank, bit;
126         struct adp5588_gpio *dev = gpiochip_get_data(chip);
127
128         bank = ADP5588_BANK(off);
129         bit = ADP5588_BIT(off);
130
131         mutex_lock(&dev->lock);
132         dev->dir[bank] |= bit;
133
134         if (val)
135                 dev->dat_out[bank] |= bit;
136         else
137                 dev->dat_out[bank] &= ~bit;
138
139         ret = adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank,
140                                  dev->dat_out[bank]);
141         ret |= adp5588_gpio_write(dev->client, GPIO_DIR1 + bank,
142                                  dev->dir[bank]);
143         mutex_unlock(&dev->lock);
144
145         return ret;
146 }
147
148 #ifdef CONFIG_GPIO_ADP5588_IRQ
149 static int adp5588_gpio_to_irq(struct gpio_chip *chip, unsigned off)
150 {
151         struct adp5588_gpio *dev = gpiochip_get_data(chip);
152
153         return dev->irq_base + off;
154 }
155
156 static void adp5588_irq_bus_lock(struct irq_data *d)
157 {
158         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
159
160         mutex_lock(&dev->irq_lock);
161 }
162
163  /*
164   * genirq core code can issue chip->mask/unmask from atomic context.
165   * This doesn't work for slow busses where an access needs to sleep.
166   * bus_sync_unlock() is therefore called outside the atomic context,
167   * syncs the current irq mask state with the slow external controller
168   * and unlocks the bus.
169   */
170
171 static void adp5588_irq_bus_sync_unlock(struct irq_data *d)
172 {
173         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
174         int i;
175
176         for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++)
177                 if (dev->int_en[i] ^ dev->irq_mask[i]) {
178                         dev->int_en[i] = dev->irq_mask[i];
179                         adp5588_gpio_write(dev->client, GPIO_INT_EN1 + i,
180                                            dev->int_en[i]);
181                 }
182
183         mutex_unlock(&dev->irq_lock);
184 }
185
186 static void adp5588_irq_mask(struct irq_data *d)
187 {
188         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
189         unsigned gpio = d->irq - dev->irq_base;
190
191         dev->irq_mask[ADP5588_BANK(gpio)] &= ~ADP5588_BIT(gpio);
192 }
193
194 static void adp5588_irq_unmask(struct irq_data *d)
195 {
196         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
197         unsigned gpio = d->irq - dev->irq_base;
198
199         dev->irq_mask[ADP5588_BANK(gpio)] |= ADP5588_BIT(gpio);
200 }
201
202 static int adp5588_irq_set_type(struct irq_data *d, unsigned int type)
203 {
204         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
205         uint16_t gpio = d->irq - dev->irq_base;
206         unsigned bank, bit;
207
208         if ((type & IRQ_TYPE_EDGE_BOTH)) {
209                 dev_err(&dev->client->dev, "irq %d: unsupported type %d\n",
210                         d->irq, type);
211                 return -EINVAL;
212         }
213
214         bank = ADP5588_BANK(gpio);
215         bit = ADP5588_BIT(gpio);
216
217         if (type & IRQ_TYPE_LEVEL_HIGH)
218                 dev->int_lvl[bank] |= bit;
219         else if (type & IRQ_TYPE_LEVEL_LOW)
220                 dev->int_lvl[bank] &= ~bit;
221         else
222                 return -EINVAL;
223
224         adp5588_gpio_direction_input(&dev->gpio_chip, gpio);
225         adp5588_gpio_write(dev->client, GPIO_INT_LVL1 + bank,
226                            dev->int_lvl[bank]);
227
228         return 0;
229 }
230
231 static struct irq_chip adp5588_irq_chip = {
232         .name                   = "adp5588",
233         .irq_mask               = adp5588_irq_mask,
234         .irq_unmask             = adp5588_irq_unmask,
235         .irq_bus_lock           = adp5588_irq_bus_lock,
236         .irq_bus_sync_unlock    = adp5588_irq_bus_sync_unlock,
237         .irq_set_type           = adp5588_irq_set_type,
238 };
239
240 static int adp5588_gpio_read_intstat(struct i2c_client *client, u8 *buf)
241 {
242         int ret = i2c_smbus_read_i2c_block_data(client, GPIO_INT_STAT1, 3, buf);
243
244         if (ret < 0)
245                 dev_err(&client->dev, "Read INT_STAT Error\n");
246
247         return ret;
248 }
249
250 static irqreturn_t adp5588_irq_handler(int irq, void *devid)
251 {
252         struct adp5588_gpio *dev = devid;
253         unsigned status, bank, bit, pending;
254         int ret;
255         status = adp5588_gpio_read(dev->client, INT_STAT);
256
257         if (status & ADP5588_GPI_INT) {
258                 ret = adp5588_gpio_read_intstat(dev->client, dev->irq_stat);
259                 if (ret < 0)
260                         memset(dev->irq_stat, 0, ARRAY_SIZE(dev->irq_stat));
261
262                 for (bank = 0, bit = 0; bank <= ADP5588_BANK(ADP5588_MAXGPIO);
263                         bank++, bit = 0) {
264                         pending = dev->irq_stat[bank] & dev->irq_mask[bank];
265
266                         while (pending) {
267                                 if (pending & (1 << bit)) {
268                                         handle_nested_irq(dev->irq_base +
269                                                           (bank << 3) + bit);
270                                         pending &= ~(1 << bit);
271
272                                 }
273                                 bit++;
274                         }
275                 }
276         }
277
278         adp5588_gpio_write(dev->client, INT_STAT, status); /* Status is W1C */
279
280         return IRQ_HANDLED;
281 }
282
283 static int adp5588_irq_setup(struct adp5588_gpio *dev)
284 {
285         struct i2c_client *client = dev->client;
286         struct adp5588_gpio_platform_data *pdata =
287                         dev_get_platdata(&client->dev);
288         unsigned gpio;
289         int ret;
290
291         adp5588_gpio_write(client, CFG, ADP5588_AUTO_INC);
292         adp5588_gpio_write(client, INT_STAT, -1); /* status is W1C */
293         adp5588_gpio_read_intstat(client, dev->irq_stat); /* read to clear */
294
295         dev->irq_base = pdata->irq_base;
296         mutex_init(&dev->irq_lock);
297
298         for (gpio = 0; gpio < dev->gpio_chip.ngpio; gpio++) {
299                 int irq = gpio + dev->irq_base;
300                 irq_set_chip_data(irq, dev);
301                 irq_set_chip_and_handler(irq, &adp5588_irq_chip,
302                                          handle_level_irq);
303                 irq_set_nested_thread(irq, 1);
304                 irq_modify_status(irq, IRQ_NOREQUEST, IRQ_NOPROBE);
305         }
306
307         ret = request_threaded_irq(client->irq,
308                                    NULL,
309                                    adp5588_irq_handler,
310                                    IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
311                                    dev_name(&client->dev), dev);
312         if (ret) {
313                 dev_err(&client->dev, "failed to request irq %d\n",
314                         client->irq);
315                 goto out;
316         }
317
318         dev->gpio_chip.to_irq = adp5588_gpio_to_irq;
319         adp5588_gpio_write(client, CFG,
320                 ADP5588_AUTO_INC | ADP5588_INT_CFG | ADP5588_GPI_INT);
321
322         return 0;
323
324 out:
325         dev->irq_base = 0;
326         return ret;
327 }
328
329 static void adp5588_irq_teardown(struct adp5588_gpio *dev)
330 {
331         if (dev->irq_base)
332                 free_irq(dev->client->irq, dev);
333 }
334
335 #else
336 static int adp5588_irq_setup(struct adp5588_gpio *dev)
337 {
338         struct i2c_client *client = dev->client;
339         dev_warn(&client->dev, "interrupt support not compiled in\n");
340
341         return 0;
342 }
343
344 static void adp5588_irq_teardown(struct adp5588_gpio *dev)
345 {
346 }
347 #endif /* CONFIG_GPIO_ADP5588_IRQ */
348
349 static int adp5588_gpio_probe(struct i2c_client *client,
350                                         const struct i2c_device_id *id)
351 {
352         struct adp5588_gpio_platform_data *pdata =
353                         dev_get_platdata(&client->dev);
354         struct adp5588_gpio *dev;
355         struct gpio_chip *gc;
356         int ret, i, revid;
357
358         if (!pdata) {
359                 dev_err(&client->dev, "missing platform data\n");
360                 return -ENODEV;
361         }
362
363         if (!i2c_check_functionality(client->adapter,
364                                         I2C_FUNC_SMBUS_BYTE_DATA)) {
365                 dev_err(&client->dev, "SMBUS Byte Data not Supported\n");
366                 return -EIO;
367         }
368
369         dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL);
370         if (!dev)
371                 return -ENOMEM;
372
373         dev->client = client;
374
375         gc = &dev->gpio_chip;
376         gc->direction_input = adp5588_gpio_direction_input;
377         gc->direction_output = adp5588_gpio_direction_output;
378         gc->get = adp5588_gpio_get_value;
379         gc->set = adp5588_gpio_set_value;
380         gc->can_sleep = true;
381
382         gc->base = pdata->gpio_start;
383         gc->ngpio = ADP5588_MAXGPIO;
384         gc->label = client->name;
385         gc->owner = THIS_MODULE;
386         gc->names = pdata->names;
387
388         mutex_init(&dev->lock);
389
390         ret = adp5588_gpio_read(dev->client, DEV_ID);
391         if (ret < 0)
392                 goto err;
393
394         revid = ret & ADP5588_DEVICE_ID_MASK;
395
396         for (i = 0, ret = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) {
397                 dev->dat_out[i] = adp5588_gpio_read(client, GPIO_DAT_OUT1 + i);
398                 dev->dir[i] = adp5588_gpio_read(client, GPIO_DIR1 + i);
399                 ret |= adp5588_gpio_write(client, KP_GPIO1 + i, 0);
400                 ret |= adp5588_gpio_write(client, GPIO_PULL1 + i,
401                                 (pdata->pullup_dis_mask >> (8 * i)) & 0xFF);
402                 ret |= adp5588_gpio_write(client, GPIO_INT_EN1 + i, 0);
403                 if (ret)
404                         goto err;
405         }
406
407         if (pdata->irq_base) {
408                 if (WA_DELAYED_READOUT_REVID(revid)) {
409                         dev_warn(&client->dev, "GPIO int not supported\n");
410                 } else {
411                         ret = adp5588_irq_setup(dev);
412                         if (ret)
413                                 goto err;
414                 }
415         }
416
417         ret = devm_gpiochip_add_data(&client->dev, &dev->gpio_chip, dev);
418         if (ret)
419                 goto err_irq;
420
421         dev_info(&client->dev, "IRQ Base: %d Rev.: %d\n",
422                         pdata->irq_base, revid);
423
424         if (pdata->setup) {
425                 ret = pdata->setup(client, gc->base, gc->ngpio, pdata->context);
426                 if (ret < 0)
427                         dev_warn(&client->dev, "setup failed, %d\n", ret);
428         }
429
430         i2c_set_clientdata(client, dev);
431
432         return 0;
433
434 err_irq:
435         adp5588_irq_teardown(dev);
436 err:
437         return ret;
438 }
439
440 static int adp5588_gpio_remove(struct i2c_client *client)
441 {
442         struct adp5588_gpio_platform_data *pdata =
443                         dev_get_platdata(&client->dev);
444         struct adp5588_gpio *dev = i2c_get_clientdata(client);
445         int ret;
446
447         if (pdata->teardown) {
448                 ret = pdata->teardown(client,
449                                       dev->gpio_chip.base, dev->gpio_chip.ngpio,
450                                       pdata->context);
451                 if (ret < 0) {
452                         dev_err(&client->dev, "teardown failed %d\n", ret);
453                         return ret;
454                 }
455         }
456
457         if (dev->irq_base)
458                 free_irq(dev->client->irq, dev);
459
460         return 0;
461 }
462
463 static const struct i2c_device_id adp5588_gpio_id[] = {
464         {DRV_NAME, 0},
465         {}
466 };
467
468 MODULE_DEVICE_TABLE(i2c, adp5588_gpio_id);
469
470 static struct i2c_driver adp5588_gpio_driver = {
471         .driver = {
472                    .name = DRV_NAME,
473                    },
474         .probe = adp5588_gpio_probe,
475         .remove = adp5588_gpio_remove,
476         .id_table = adp5588_gpio_id,
477 };
478
479 module_i2c_driver(adp5588_gpio_driver);
480
481 MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
482 MODULE_DESCRIPTION("GPIO ADP5588 Driver");
483 MODULE_LICENSE("GPL");