2 * INET An implementation of the TCP/IP protocol suite for the LINUX
3 * operating system. NET is implemented using the BSD Socket
4 * interface as the means of communication with the user level.
6 * Definitions used by the ARCnet driver.
8 * Authors: Avery Pennarun and David Woodhouse
10 * This program is free software; you can redistribute it and/or
11 * modify it under the terms of the GNU General Public License
12 * as published by the Free Software Foundation; either version
13 * 2 of the License, or (at your option) any later version.
16 #ifndef _LINUX_ARCDEVICE_H
17 #define _LINUX_ARCDEVICE_H
19 #include <asm/timex.h>
20 #include <linux/if_arcnet.h>
23 #include <linux/irqreturn.h>
26 * RECON_THRESHOLD is the maximum number of RECON messages to receive
27 * within one minute before printing a "cabling problem" warning. The
28 * default value should be fine.
30 * After that, a "cabling restored" message will be printed on the next IRQ
31 * if no RECON messages have been received for 10 seconds.
33 * Do not define RECON_THRESHOLD at all if you want to disable this feature.
35 #define RECON_THRESHOLD 30
38 * Define this to the minimum "timeout" value. If a transmit takes longer
39 * than TX_TIMEOUT jiffies, Linux will abort the TX and retry. On a large
40 * network, or one with heavy network traffic, this timeout may need to be
41 * increased. The larger it is, though, the longer it will be between
42 * necessary transmits - don't set this too high.
44 #define TX_TIMEOUT (HZ * 200 / 1000)
46 /* Display warnings about the driver being an ALPHA version. */
50 * Debugging bitflags: each option can be enabled individually.
52 * Note: only debug flags included in the ARCNET_DEBUG_MAX define will
53 * actually be available. GCC will (at least, GCC 2.7.0 will) notice
54 * lines using a BUGLVL not in ARCNET_DEBUG_MAX and automatically optimize
57 #define D_NORMAL 1 /* important operational info */
58 #define D_EXTRA 2 /* useful, but non-vital information */
59 #define D_INIT 4 /* show init/probe messages */
60 #define D_INIT_REASONS 8 /* show reasons for discarding probes */
61 #define D_RECON 32 /* print a message whenever token is lost */
62 #define D_PROTO 64 /* debug auto-protocol support */
63 /* debug levels below give LOTS of output during normal operation! */
64 #define D_DURING 128 /* trace operations (including irq's) */
65 #define D_TX 256 /* show tx packets */
66 #define D_RX 512 /* show rx packets */
67 #define D_SKB 1024 /* show skb's */
68 #define D_SKB_SIZE 2048 /* show skb sizes */
69 #define D_TIMING 4096 /* show time needed to copy buffers to card */
70 #define D_DEBUG 8192 /* Very detailed debug line for line */
72 #ifndef ARCNET_DEBUG_MAX
73 #define ARCNET_DEBUG_MAX (127) /* change to ~0 if you want detailed debugging */
77 #define ARCNET_DEBUG (D_NORMAL | D_EXTRA)
79 extern int arcnet_debug;
81 #define BUGLVL(x) ((x) & ARCNET_DEBUG_MAX & arcnet_debug)
83 /* macros to simplify debug checking */
84 #define arc_printk(x, dev, fmt, ...) \
87 if ((x) == D_NORMAL) \
88 netdev_warn(dev, fmt, ##__VA_ARGS__); \
89 else if ((x) < D_DURING) \
90 netdev_info(dev, fmt, ##__VA_ARGS__); \
92 netdev_dbg(dev, fmt, ##__VA_ARGS__); \
96 #define arc_cont(x, fmt, ...) \
99 pr_cont(fmt, ##__VA_ARGS__); \
102 /* see how long a function call takes to run, expressed in CPU cycles */
103 #define TIME(dev, name, bytes, call) \
105 if (BUGLVL(D_TIMING)) { \
106 unsigned long _x, _y; \
110 arc_printk(D_TIMING, dev, \
111 "%s: %d bytes in %lu cycles == %lu Kbytes/100Mcycle\n", \
112 name, bytes, _y - _x, \
113 100000000 / 1024 * bytes / (_y - _x + 1)); \
120 * Time needed to reset the card - in ms (milliseconds). This works on my
121 * SMC PC100. I can't find a reference that tells me just how long I
124 #define RESETtime (300)
127 * These are the max/min lengths of packet payload, not including the
128 * arc_hardware header, but definitely including the soft header.
130 * Note: packet sizes 254, 255, 256 are impossible because of the way
131 * ARCnet registers work That's why RFC1201 defines "exception" packets.
132 * In non-RFC1201 protocols, we have to just tack some extra bytes on the
135 #define MTU 253 /* normal packet max size */
136 #define MinTU 257 /* extended packet min size */
137 #define XMTU 508 /* extended packet max size */
139 /* status/interrupt mask bit fields */
140 #define TXFREEflag 0x01 /* transmitter available */
141 #define TXACKflag 0x02 /* transmitted msg. ackd */
142 #define RECONflag 0x04 /* network reconfigured */
143 #define TESTflag 0x08 /* test flag */
144 #define EXCNAKflag 0x08 /* excesive nak flag */
145 #define RESETflag 0x10 /* power-on-reset */
146 #define RES1flag 0x20 /* reserved - usually set by jumper */
147 #define RES2flag 0x40 /* reserved - usually set by jumper */
148 #define NORXflag 0x80 /* receiver inhibited */
150 /* Flags used for IO-mapped memory operations */
151 #define AUTOINCflag 0x40 /* Increase location with each access */
152 #define IOMAPflag 0x02 /* (for 90xx) Use IO mapped memory, not mmap */
153 #define ENABLE16flag 0x80 /* (for 90xx) Enable 16-bit mode */
155 /* in the command register, the following bits have these meanings:
157 * 3-4 page number (for enable rcv/xmt command)
158 * 7 receive broadcasts
160 #define NOTXcmd 0x01 /* disable transmitter */
161 #define NORXcmd 0x02 /* disable receiver */
162 #define TXcmd 0x03 /* enable transmitter */
163 #define RXcmd 0x04 /* enable receiver */
164 #define CONFIGcmd 0x05 /* define configuration */
165 #define CFLAGScmd 0x06 /* clear flags */
166 #define TESTcmd 0x07 /* load test flags */
168 /* flags for "clear flags" command */
169 #define RESETclear 0x08 /* power-on-reset */
170 #define CONFIGclear 0x10 /* system reconfigured */
172 #define EXCNAKclear 0x0E /* Clear and acknowledge the excive nak bit */
174 /* flags for "load test flags" command */
175 #define TESTload 0x08 /* test flag (diagnostic) */
177 /* byte deposited into first address of buffers on reset */
178 #define TESTvalue 0321 /* that's octal for 0xD1 :) */
180 /* for "enable receiver" command */
181 #define RXbcasts 0x80 /* receive broadcasts */
183 /* flags for "define configuration" command */
184 #define NORMALconf 0x00 /* 1-249 byte packets */
185 #define EXTconf 0x08 /* 250-504 byte packets */
187 /* card feature flags, set during auto-detection.
188 * (currently only used by com20020pci)
190 #define ARC_IS_5MBIT 1 /* card default speed is 5MBit */
191 #define ARC_CAN_10MBIT 2 /* card uses COM20022, supporting 10MBit,
192 but default is 2.5MBit. */
194 /* information needed to define an encapsulation driver */
196 char suffix; /* a for RFC1201, e for ether-encap, etc. */
197 int mtu; /* largest possible packet */
198 int is_ip; /* This is a ip plugin - not a raw thing */
200 void (*rx)(struct net_device *dev, int bufnum,
201 struct archdr *pkthdr, int length);
202 int (*build_header)(struct sk_buff *skb, struct net_device *dev,
203 unsigned short ethproto, uint8_t daddr);
205 /* these functions return '1' if the skb can now be freed */
206 int (*prepare_tx)(struct net_device *dev, struct archdr *pkt,
207 int length, int bufnum);
208 int (*continue_tx)(struct net_device *dev, int bufnum);
209 int (*ack_tx)(struct net_device *dev, int acked);
212 extern struct ArcProto *arc_proto_map[256], *arc_proto_default,
213 *arc_bcast_proto, *arc_raw_proto;
216 * "Incoming" is information needed for each address that could be sending
217 * to us. Mostly for partially-received split packets.
220 struct sk_buff *skb; /* packet data buffer */
221 __be16 sequence; /* sequence number of assembly */
222 uint8_t lastpacket, /* number of last packet (from 1) */
223 numpackets; /* number of packets in split */
226 /* only needed for RFC1201 */
228 struct ArcProto *proto; /* protocol driver that owns this:
229 * if NULL, no packet is pending.
231 struct sk_buff *skb; /* buffer from upper levels */
232 struct archdr *pkt; /* a pointer into the skb */
233 uint16_t length, /* bytes total */
234 dataleft, /* bytes left */
235 segnum, /* segment being sent */
236 numsegs; /* number of segments */
239 struct arcnet_local {
240 uint8_t config, /* current value of CONFIG register */
241 timeout, /* Extended timeout for COM20020 */
242 backplane, /* Backplane flag for COM20020 */
243 clockp, /* COM20020 clock divider */
244 clockm, /* COM20020 clock multiplier flag */
245 setup, /* Contents of setup1 register */
246 setup2, /* Contents of setup2 register */
247 intmask; /* current value of INTMASK register */
248 uint8_t default_proto[256]; /* default encap to use for each host */
249 int cur_tx, /* buffer used by current transmit, or -1 */
250 next_tx, /* buffer where a packet is ready to send */
251 cur_rx; /* current receive buffer */
252 int lastload_dest, /* can last loaded packet be acked? */
253 lasttrans_dest; /* can last TX'd packet be acked? */
254 int timed_out; /* need to process TX timeout and drop packet */
255 unsigned long last_timeout; /* time of last reported timeout */
256 char *card_name; /* card ident string */
257 int card_flags; /* special card features */
259 /* On preemtive and SMB a lock is needed */
263 * Buffer management: an ARCnet card has 4 x 512-byte buffers, each of
264 * which can be used for either sending or receiving. The new dynamic
265 * buffer management routines use a simple circular queue of available
266 * buffers, and take them as they're needed. This way, we simplify
267 * situations in which we (for example) want to pre-load a transmit
268 * buffer, or start receiving while we copy a received packet to
271 * The rules: only the interrupt handler is allowed to _add_ buffers to
272 * the queue; thus, this doesn't require a lock. Both the interrupt
273 * handler and the transmit function will want to _remove_ buffers, so
274 * we need to handle the situation where they try to do it at the same
277 * If next_buf == first_free_buf, the queue is empty. Since there are
278 * only four possible buffers, the queue should never be full.
282 int next_buf, first_free_buf;
284 /* network "reconfiguration" handling */
285 unsigned long first_recon; /* time of "first" RECON message to count */
286 unsigned long last_recon; /* time of most recent RECON */
287 int num_recons; /* number of RECONs between first and last. */
288 int network_down; /* do we think the network is down? */
290 int excnak_pending; /* We just got an excesive nak interrupt */
293 uint16_t sequence; /* sequence number (incs with each packet) */
296 struct Incoming incoming[256]; /* one from each address */
299 /* really only used by rfc1201, but we'll pretend it's not */
300 struct Outgoing outgoing; /* packet currently being sent */
302 /* hardware-specific functions */
304 struct module *owner;
305 void (*command)(struct net_device *dev, int cmd);
306 int (*status)(struct net_device *dev);
307 void (*intmask)(struct net_device *dev, int mask);
308 int (*reset)(struct net_device *dev, int really_reset);
309 void (*open)(struct net_device *dev);
310 void (*close)(struct net_device *dev);
312 void (*copy_to_card)(struct net_device *dev, int bufnum,
313 int offset, void *buf, int count);
314 void (*copy_from_card)(struct net_device *dev, int bufnum,
315 int offset, void *buf, int count);
318 void __iomem *mem_start; /* pointer to ioremap'ed MMIO */
321 #define ARCRESET(x) (lp->hw.reset(dev, (x)))
322 #define ACOMMAND(x) (lp->hw.command(dev, (x)))
323 #define ASTATUS() (lp->hw.status(dev))
324 #define AINTMASK(x) (lp->hw.intmask(dev, (x)))
326 #if ARCNET_DEBUG_MAX & D_SKB
327 void arcnet_dump_skb(struct net_device *dev, struct sk_buff *skb, char *desc);
330 void arcnet_dump_skb(struct net_device *dev, struct sk_buff *skb, char *desc)
335 void arcnet_unregister_proto(struct ArcProto *proto);
336 irqreturn_t arcnet_interrupt(int irq, void *dev_id);
337 struct net_device *alloc_arcdev(const char *name);
339 int arcnet_open(struct net_device *dev);
340 int arcnet_close(struct net_device *dev);
341 netdev_tx_t arcnet_send_packet(struct sk_buff *skb,
342 struct net_device *dev);
343 void arcnet_timeout(struct net_device *dev);
345 /* I/O equivalents */
347 /* addr and offset allow register like names to define the actual IO address.
348 * A configuration option multiplies the offset for alignment.
350 #define arcnet_inb(addr, offset) \
351 inb((addr) + (offset))
352 #define arcnet_outb(value, addr, offset) \
353 outb(value, (addr) + (offset))
355 #define arcnet_insb(addr, offset, buffer, count) \
356 insb((addr) + (offset), buffer, count)
357 #define arcnet_outsb(addr, offset, buffer, count) \
358 outsb((addr) + (offset), buffer, count)
360 #define arcnet_inw(addr, offset) \
361 inw((addr) + (offset))
362 #define arcnet_outw(value, addr, offset) \
363 outw(value, (addr) + (offset))
365 #define arcnet_insw(addr, offset, buffer, count) \
366 insw((addr) + (offset), buffer, count)
367 #define arcnet_outsw(addr, offset, buffer, count) \
368 outsw((addr) + (offset), buffer, count)
370 #endif /* __KERNEL__ */
371 #endif /* _LINUX_ARCDEVICE_H */