2 * Silicon Laboratories CP210x USB to RS232 serial adaptor driver
4 * Copyright (C) 2005 Craig Shelley (craig@microtron.org.uk)
6 * This program is free software; you can redistribute it and/or
7 * modify it under the terms of the GNU General Public License version
8 * 2 as published by the Free Software Foundation.
10 * Support to set flow control line levels using TIOCMGET and TIOCMSET
11 * thanks to Karl Hiramoto karl@hiramoto.org. RTSCTS hardware flow
12 * control thanks to Munir Nassar nassarmu@real-time.com
16 #include <linux/kernel.h>
17 #include <linux/errno.h>
18 #include <linux/slab.h>
19 #include <linux/tty.h>
20 #include <linux/tty_flip.h>
21 #include <linux/module.h>
22 #include <linux/moduleparam.h>
23 #include <linux/usb.h>
24 #include <linux/uaccess.h>
25 #include <linux/usb/serial.h>
27 #define DRIVER_DESC "Silicon Labs CP210x RS232 serial adaptor driver"
32 static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *);
33 static void cp210x_close(struct usb_serial_port *);
34 static void cp210x_get_termios(struct tty_struct *, struct usb_serial_port *);
35 static void cp210x_get_termios_port(struct usb_serial_port *port,
36 unsigned int *cflagp, unsigned int *baudp);
37 static void cp210x_change_speed(struct tty_struct *, struct usb_serial_port *,
39 static void cp210x_set_termios(struct tty_struct *, struct usb_serial_port *,
41 static bool cp210x_tx_empty(struct usb_serial_port *port);
42 static int cp210x_tiocmget(struct tty_struct *);
43 static int cp210x_tiocmset(struct tty_struct *, unsigned int, unsigned int);
44 static int cp210x_tiocmset_port(struct usb_serial_port *port,
45 unsigned int, unsigned int);
46 static void cp210x_break_ctl(struct tty_struct *, int);
47 static int cp210x_port_probe(struct usb_serial_port *);
48 static int cp210x_port_remove(struct usb_serial_port *);
49 static void cp210x_dtr_rts(struct usb_serial_port *p, int on);
51 static const struct usb_device_id id_table[] = {
52 { USB_DEVICE(0x045B, 0x0053) }, /* Renesas RX610 RX-Stick */
53 { USB_DEVICE(0x0471, 0x066A) }, /* AKTAKOM ACE-1001 cable */
54 { USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
55 { USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
56 { USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */
57 { USB_DEVICE(0x0846, 0x1100) }, /* NetGear Managed Switch M4100 series, M5300 series, M7100 series */
58 { USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */
59 { USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */
60 { USB_DEVICE(0x0908, 0x01FF) }, /* Siemens RUGGEDCOM USB Serial Console */
61 { USB_DEVICE(0x0BED, 0x1100) }, /* MEI (TM) Cashflow-SC Bill/Voucher Acceptor */
62 { USB_DEVICE(0x0BED, 0x1101) }, /* MEI series 2000 Combo Acceptor */
63 { USB_DEVICE(0x0FCF, 0x1003) }, /* Dynastream ANT development board */
64 { USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */
65 { USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */
66 { USB_DEVICE(0x0FDE, 0xCA05) }, /* OWL Wireless Electricity Monitor CM-160 */
67 { USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */
68 { USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */
69 { USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */
70 { USB_DEVICE(0x10C4, 0x0F91) }, /* Vstabi */
71 { USB_DEVICE(0x10C4, 0x1101) }, /* Arkham Technology DS101 Bus Monitor */
72 { USB_DEVICE(0x10C4, 0x1601) }, /* Arkham Technology DS101 Adapter */
73 { USB_DEVICE(0x10C4, 0x800A) }, /* SPORTident BSM7-D-USB main station */
74 { USB_DEVICE(0x10C4, 0x803B) }, /* Pololu USB-serial converter */
75 { USB_DEVICE(0x10C4, 0x8044) }, /* Cygnal Debug Adapter */
76 { USB_DEVICE(0x10C4, 0x804E) }, /* Software Bisque Paramount ME build-in converter */
77 { USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */
78 { USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */
79 { USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */
80 { USB_DEVICE(0x10C4, 0x806F) }, /* IMS USB to RS422 Converter Cable */
81 { USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */
82 { USB_DEVICE(0x10C4, 0x80C4) }, /* Cygnal Integrated Products, Inc., Optris infrared thermometer */
83 { USB_DEVICE(0x10C4, 0x80CA) }, /* Degree Controls Inc */
84 { USB_DEVICE(0x10C4, 0x80DD) }, /* Tracient RFID */
85 { USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */
86 { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */
87 { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */
88 { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */
89 { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */
90 { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */
91 { USB_DEVICE(0x2405, 0x0003) }, /* West Mountain Radio RIGblaster Advantage */
92 { USB_DEVICE(0x10C4, 0x8156) }, /* B&G H3000 link cable */
93 { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */
94 { USB_DEVICE(0x10C4, 0x815F) }, /* Timewave HamLinkUSB */
95 { USB_DEVICE(0x10C4, 0x818B) }, /* AVIT Research USB to TTL */
96 { USB_DEVICE(0x10C4, 0x819F) }, /* MJS USB Toslink Switcher */
97 { USB_DEVICE(0x10C4, 0x81A6) }, /* ThinkOptics WavIt */
98 { USB_DEVICE(0x10C4, 0x81A9) }, /* Multiplex RC Interface */
99 { USB_DEVICE(0x10C4, 0x81AC) }, /* MSD Dash Hawk */
100 { USB_DEVICE(0x10C4, 0x81AD) }, /* INSYS USB Modem */
101 { USB_DEVICE(0x10C4, 0x81C8) }, /* Lipowsky Industrie Elektronik GmbH, Baby-JTAG */
102 { USB_DEVICE(0x10C4, 0x81E2) }, /* Lipowsky Industrie Elektronik GmbH, Baby-LIN */
103 { USB_DEVICE(0x10C4, 0x81E7) }, /* Aerocomm Radio */
104 { USB_DEVICE(0x10C4, 0x81E8) }, /* Zephyr Bioharness */
105 { USB_DEVICE(0x10C4, 0x81F2) }, /* C1007 HF band RFID controller */
106 { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */
107 { USB_DEVICE(0x10C4, 0x822B) }, /* Modem EDGE(GSM) Comander 2 */
108 { USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demonstration module */
109 { USB_DEVICE(0x10C4, 0x8281) }, /* Nanotec Plug & Drive */
110 { USB_DEVICE(0x10C4, 0x8293) }, /* Telegesis ETRX2USB */
111 { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */
112 { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */
113 { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */
114 { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */
115 { USB_DEVICE(0x10C4, 0x83D8) }, /* DekTec DTA Plus VHF/UHF Booster/Attenuator */
116 { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
117 { USB_DEVICE(0x10C4, 0x8418) }, /* IRZ Automation Teleport SG-10 GSM/GPRS Modem */
118 { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
119 { USB_DEVICE(0x10C4, 0x8477) }, /* Balluff RFID */
120 { USB_DEVICE(0x10C4, 0x85EA) }, /* AC-Services IBUS-IF */
121 { USB_DEVICE(0x10C4, 0x85EB) }, /* AC-Services CIS-IBUS */
122 { USB_DEVICE(0x10C4, 0x85F8) }, /* Virtenio Preon32 */
123 { USB_DEVICE(0x10C4, 0x8664) }, /* AC-Services CAN-IF */
124 { USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */
125 { USB_DEVICE(0x10C4, 0x8856) }, /* CEL EM357 ZigBee USB Stick - LR */
126 { USB_DEVICE(0x10C4, 0x8857) }, /* CEL EM357 ZigBee USB Stick */
127 { USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */
128 { USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */
129 { USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */
130 { USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */
131 { USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */
132 { USB_DEVICE(0x10C4, 0x8A2A) }, /* HubZ dual ZigBee and Z-Wave dongle */
133 { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
134 { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
135 { USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */
136 { USB_DEVICE(0x10C4, 0xEA71) }, /* Infinity GPS-MIC-1 Radio Monophone */
137 { USB_DEVICE(0x10C4, 0xF001) }, /* Elan Digital Systems USBscope50 */
138 { USB_DEVICE(0x10C4, 0xF002) }, /* Elan Digital Systems USBwave12 */
139 { USB_DEVICE(0x10C4, 0xF003) }, /* Elan Digital Systems USBpulse100 */
140 { USB_DEVICE(0x10C4, 0xF004) }, /* Elan Digital Systems USBcount50 */
141 { USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */
142 { USB_DEVICE(0x10CE, 0xEA6A) }, /* Silicon Labs MobiData GPRS USB Modem 100EU */
143 { USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
144 { USB_DEVICE(0x1555, 0x0004) }, /* Owen AC4 USB-RS485 Converter */
145 { USB_DEVICE(0x166A, 0x0201) }, /* Clipsal 5500PACA C-Bus Pascal Automation Controller */
146 { USB_DEVICE(0x166A, 0x0301) }, /* Clipsal 5800PC C-Bus Wireless PC Interface */
147 { USB_DEVICE(0x166A, 0x0303) }, /* Clipsal 5500PCU C-Bus USB interface */
148 { USB_DEVICE(0x166A, 0x0304) }, /* Clipsal 5000CT2 C-Bus Black and White Touchscreen */
149 { USB_DEVICE(0x166A, 0x0305) }, /* Clipsal C-5000CT2 C-Bus Spectrum Colour Touchscreen */
150 { USB_DEVICE(0x166A, 0x0401) }, /* Clipsal L51xx C-Bus Architectural Dimmer */
151 { USB_DEVICE(0x166A, 0x0101) }, /* Clipsal 5560884 C-Bus Multi-room Audio Matrix Switcher */
152 { USB_DEVICE(0x16C0, 0x09B0) }, /* Lunatico Seletek */
153 { USB_DEVICE(0x16C0, 0x09B1) }, /* Lunatico Seletek */
154 { USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */
155 { USB_DEVICE(0x16DC, 0x0010) }, /* W-IE-NE-R Plein & Baus GmbH PL512 Power Supply */
156 { USB_DEVICE(0x16DC, 0x0011) }, /* W-IE-NE-R Plein & Baus GmbH RCM Remote Control for MARATON Power Supply */
157 { USB_DEVICE(0x16DC, 0x0012) }, /* W-IE-NE-R Plein & Baus GmbH MPOD Multi Channel Power Supply */
158 { USB_DEVICE(0x16DC, 0x0015) }, /* W-IE-NE-R Plein & Baus GmbH CML Control, Monitoring and Data Logger */
159 { USB_DEVICE(0x17A8, 0x0001) }, /* Kamstrup Optical Eye/3-wire */
160 { USB_DEVICE(0x17A8, 0x0005) }, /* Kamstrup M-Bus Master MultiPort 250D */
161 { USB_DEVICE(0x17F4, 0xAAAA) }, /* Wavesense Jazz blood glucose meter */
162 { USB_DEVICE(0x1843, 0x0200) }, /* Vaisala USB Instrument Cable */
163 { USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */
164 { USB_DEVICE(0x18EF, 0xE025) }, /* ELV Marble Sound Board 1 */
165 { USB_DEVICE(0x1ADB, 0x0001) }, /* Schweitzer Engineering C662 Cable */
166 { USB_DEVICE(0x1B1C, 0x1C00) }, /* Corsair USB Dongle */
167 { USB_DEVICE(0x1BA4, 0x0002) }, /* Silicon Labs 358x factory default */
168 { USB_DEVICE(0x1BE3, 0x07A6) }, /* WAGO 750-923 USB Service Cable */
169 { USB_DEVICE(0x1D6F, 0x0010) }, /* Seluxit ApS RF Dongle */
170 { USB_DEVICE(0x1E29, 0x0102) }, /* Festo CPX-USB */
171 { USB_DEVICE(0x1E29, 0x0501) }, /* Festo CMSP */
172 { USB_DEVICE(0x1FB9, 0x0100) }, /* Lake Shore Model 121 Current Source */
173 { USB_DEVICE(0x1FB9, 0x0200) }, /* Lake Shore Model 218A Temperature Monitor */
174 { USB_DEVICE(0x1FB9, 0x0201) }, /* Lake Shore Model 219 Temperature Monitor */
175 { USB_DEVICE(0x1FB9, 0x0202) }, /* Lake Shore Model 233 Temperature Transmitter */
176 { USB_DEVICE(0x1FB9, 0x0203) }, /* Lake Shore Model 235 Temperature Transmitter */
177 { USB_DEVICE(0x1FB9, 0x0300) }, /* Lake Shore Model 335 Temperature Controller */
178 { USB_DEVICE(0x1FB9, 0x0301) }, /* Lake Shore Model 336 Temperature Controller */
179 { USB_DEVICE(0x1FB9, 0x0302) }, /* Lake Shore Model 350 Temperature Controller */
180 { USB_DEVICE(0x1FB9, 0x0303) }, /* Lake Shore Model 371 AC Bridge */
181 { USB_DEVICE(0x1FB9, 0x0400) }, /* Lake Shore Model 411 Handheld Gaussmeter */
182 { USB_DEVICE(0x1FB9, 0x0401) }, /* Lake Shore Model 425 Gaussmeter */
183 { USB_DEVICE(0x1FB9, 0x0402) }, /* Lake Shore Model 455A Gaussmeter */
184 { USB_DEVICE(0x1FB9, 0x0403) }, /* Lake Shore Model 475A Gaussmeter */
185 { USB_DEVICE(0x1FB9, 0x0404) }, /* Lake Shore Model 465 Three Axis Gaussmeter */
186 { USB_DEVICE(0x1FB9, 0x0600) }, /* Lake Shore Model 625A Superconducting MPS */
187 { USB_DEVICE(0x1FB9, 0x0601) }, /* Lake Shore Model 642A Magnet Power Supply */
188 { USB_DEVICE(0x1FB9, 0x0602) }, /* Lake Shore Model 648 Magnet Power Supply */
189 { USB_DEVICE(0x1FB9, 0x0700) }, /* Lake Shore Model 737 VSM Controller */
190 { USB_DEVICE(0x1FB9, 0x0701) }, /* Lake Shore Model 776 Hall Matrix */
191 { USB_DEVICE(0x2626, 0xEA60) }, /* Aruba Networks 7xxx USB Serial Console */
192 { USB_DEVICE(0x3195, 0xF190) }, /* Link Instruments MSO-19 */
193 { USB_DEVICE(0x3195, 0xF280) }, /* Link Instruments MSO-28 */
194 { USB_DEVICE(0x3195, 0xF281) }, /* Link Instruments MSO-28 */
195 { USB_DEVICE(0x413C, 0x9500) }, /* DW700 GPS USB interface */
196 { } /* Terminating Entry */
199 MODULE_DEVICE_TABLE(usb, id_table);
201 struct cp210x_port_private {
202 __u8 bInterfaceNumber;
203 bool has_swapped_line_ctl;
206 static struct usb_serial_driver cp210x_device = {
208 .owner = THIS_MODULE,
211 .id_table = id_table,
214 .bulk_out_size = 256,
216 .close = cp210x_close,
217 .break_ctl = cp210x_break_ctl,
218 .set_termios = cp210x_set_termios,
219 .tx_empty = cp210x_tx_empty,
220 .tiocmget = cp210x_tiocmget,
221 .tiocmset = cp210x_tiocmset,
222 .port_probe = cp210x_port_probe,
223 .port_remove = cp210x_port_remove,
224 .dtr_rts = cp210x_dtr_rts
227 static struct usb_serial_driver * const serial_drivers[] = {
231 /* Config request types */
232 #define REQTYPE_HOST_TO_INTERFACE 0x41
233 #define REQTYPE_INTERFACE_TO_HOST 0xc1
234 #define REQTYPE_HOST_TO_DEVICE 0x40
235 #define REQTYPE_DEVICE_TO_HOST 0xc0
237 /* Config request codes */
238 #define CP210X_IFC_ENABLE 0x00
239 #define CP210X_SET_BAUDDIV 0x01
240 #define CP210X_GET_BAUDDIV 0x02
241 #define CP210X_SET_LINE_CTL 0x03
242 #define CP210X_GET_LINE_CTL 0x04
243 #define CP210X_SET_BREAK 0x05
244 #define CP210X_IMM_CHAR 0x06
245 #define CP210X_SET_MHS 0x07
246 #define CP210X_GET_MDMSTS 0x08
247 #define CP210X_SET_XON 0x09
248 #define CP210X_SET_XOFF 0x0A
249 #define CP210X_SET_EVENTMASK 0x0B
250 #define CP210X_GET_EVENTMASK 0x0C
251 #define CP210X_SET_CHAR 0x0D
252 #define CP210X_GET_CHARS 0x0E
253 #define CP210X_GET_PROPS 0x0F
254 #define CP210X_GET_COMM_STATUS 0x10
255 #define CP210X_RESET 0x11
256 #define CP210X_PURGE 0x12
257 #define CP210X_SET_FLOW 0x13
258 #define CP210X_GET_FLOW 0x14
259 #define CP210X_EMBED_EVENTS 0x15
260 #define CP210X_GET_EVENTSTATE 0x16
261 #define CP210X_SET_CHARS 0x19
262 #define CP210X_GET_BAUDRATE 0x1D
263 #define CP210X_SET_BAUDRATE 0x1E
265 /* CP210X_IFC_ENABLE */
266 #define UART_ENABLE 0x0001
267 #define UART_DISABLE 0x0000
269 /* CP210X_(SET|GET)_BAUDDIV */
270 #define BAUD_RATE_GEN_FREQ 0x384000
272 /* CP210X_(SET|GET)_LINE_CTL */
273 #define BITS_DATA_MASK 0X0f00
274 #define BITS_DATA_5 0X0500
275 #define BITS_DATA_6 0X0600
276 #define BITS_DATA_7 0X0700
277 #define BITS_DATA_8 0X0800
278 #define BITS_DATA_9 0X0900
280 #define BITS_PARITY_MASK 0x00f0
281 #define BITS_PARITY_NONE 0x0000
282 #define BITS_PARITY_ODD 0x0010
283 #define BITS_PARITY_EVEN 0x0020
284 #define BITS_PARITY_MARK 0x0030
285 #define BITS_PARITY_SPACE 0x0040
287 #define BITS_STOP_MASK 0x000f
288 #define BITS_STOP_1 0x0000
289 #define BITS_STOP_1_5 0x0001
290 #define BITS_STOP_2 0x0002
292 /* CP210X_SET_BREAK */
293 #define BREAK_ON 0x0001
294 #define BREAK_OFF 0x0000
296 /* CP210X_(SET_MHS|GET_MDMSTS) */
297 #define CONTROL_DTR 0x0001
298 #define CONTROL_RTS 0x0002
299 #define CONTROL_CTS 0x0010
300 #define CONTROL_DSR 0x0020
301 #define CONTROL_RING 0x0040
302 #define CONTROL_DCD 0x0080
303 #define CONTROL_WRITE_DTR 0x0100
304 #define CONTROL_WRITE_RTS 0x0200
306 /* CP210X_GET_COMM_STATUS returns these 0x13 bytes */
307 struct cp210x_comm_status {
309 __le32 ulHoldReasons;
310 __le32 ulAmountInInQueue;
311 __le32 ulAmountInOutQueue;
313 u8 bWaitForImmediate;
318 * CP210X_PURGE - 16 bits passed in wValue of USB request.
319 * SiLabs app note AN571 gives a strange description of the 4 bits:
320 * bit 0 or bit 2 clears the transmit queue and 1 or 3 receive.
321 * writing 1 to all, however, purges cp2108 well enough to avoid the hang.
323 #define PURGE_ALL 0x000f
327 * Reads from the CP210x configuration registers
328 * 'size' is specified in bytes.
329 * 'data' is a pointer to a pre-allocated array of integers large
330 * enough to hold 'size' bytes (with 4 bytes to each integer)
332 static int cp210x_get_config(struct usb_serial_port *port, u8 request,
333 unsigned int *data, int size)
335 struct usb_serial *serial = port->serial;
336 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
338 int result, i, length;
340 /* Number of integers required to contain the array */
341 length = (((size - 1) | 3) + 1) / 4;
343 buf = kcalloc(length, sizeof(__le32), GFP_KERNEL);
347 /* Issue the request, attempting to read 'size' bytes */
348 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
349 request, REQTYPE_INTERFACE_TO_HOST, 0x0000,
350 port_priv->bInterfaceNumber, buf, size,
351 USB_CTRL_GET_TIMEOUT);
353 /* Convert data into an array of integers */
354 for (i = 0; i < length; i++)
355 data[i] = le32_to_cpu(buf[i]);
359 if (result != size) {
360 dev_dbg(&port->dev, "%s - Unable to send config request, request=0x%x size=%d result=%d\n",
361 __func__, request, size, result);
373 * Writes to the CP210x configuration registers
374 * Values less than 16 bits wide are sent directly
375 * 'size' is specified in bytes.
377 static int cp210x_set_config(struct usb_serial_port *port, u8 request,
378 unsigned int *data, int size)
380 struct usb_serial *serial = port->serial;
381 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
383 int result, i, length;
385 /* Number of integers required to contain the array */
386 length = (((size - 1) | 3) + 1) / 4;
388 buf = kmalloc(length * sizeof(__le32), GFP_KERNEL);
392 /* Array of integers into bytes */
393 for (i = 0; i < length; i++)
394 buf[i] = cpu_to_le32(data[i]);
397 result = usb_control_msg(serial->dev,
398 usb_sndctrlpipe(serial->dev, 0),
399 request, REQTYPE_HOST_TO_INTERFACE, 0x0000,
400 port_priv->bInterfaceNumber, buf, size,
401 USB_CTRL_SET_TIMEOUT);
403 result = usb_control_msg(serial->dev,
404 usb_sndctrlpipe(serial->dev, 0),
405 request, REQTYPE_HOST_TO_INTERFACE, data[0],
406 port_priv->bInterfaceNumber, NULL, 0,
407 USB_CTRL_SET_TIMEOUT);
412 if ((size > 2 && result != size) || result < 0) {
413 dev_dbg(&port->dev, "%s - Unable to send request, request=0x%x size=%d result=%d\n",
414 __func__, request, size, result);
425 * cp210x_set_config_single
426 * Convenience function for calling cp210x_set_config on single data values
427 * without requiring an integer pointer
429 static inline int cp210x_set_config_single(struct usb_serial_port *port,
430 u8 request, unsigned int data)
432 return cp210x_set_config(port, request, &data, 2);
436 * Detect CP2108 GET_LINE_CTL bug and activate workaround.
437 * Write a known good value 0x800, read it back.
438 * If it comes back swapped the bug is detected.
439 * Preserve the original register value.
441 static int cp210x_detect_swapped_line_ctl(struct usb_serial_port *port)
443 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
444 unsigned int line_ctl_save;
445 unsigned int line_ctl_test;
448 err = cp210x_get_config(port, CP210X_GET_LINE_CTL, &line_ctl_save, 2);
452 line_ctl_test = 0x800;
453 err = cp210x_set_config(port, CP210X_SET_LINE_CTL, &line_ctl_test, 2);
457 err = cp210x_get_config(port, CP210X_GET_LINE_CTL, &line_ctl_test, 2);
461 if (line_ctl_test == 8) {
462 port_priv->has_swapped_line_ctl = true;
463 line_ctl_save = swab16((u16)line_ctl_save);
466 return cp210x_set_config(port, CP210X_SET_LINE_CTL, &line_ctl_save, 2);
470 * Must always be called instead of cp210x_get_config(CP210X_GET_LINE_CTL)
471 * to workaround cp2108 bug and get correct value.
473 static int cp210x_get_line_ctl(struct usb_serial_port *port, unsigned int *ctl)
475 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
478 err = cp210x_get_config(port, CP210X_GET_LINE_CTL, ctl, 2);
482 /* Workaround swapped bytes in 16-bit value from CP210X_GET_LINE_CTL */
483 if (port_priv->has_swapped_line_ctl)
484 *ctl = swab16((u16)(*ctl));
490 * cp210x_quantise_baudrate
491 * Quantises the baud rate as per AN205 Table 1
493 static unsigned int cp210x_quantise_baudrate(unsigned int baud)
497 else if (baud <= 600) baud = 600;
498 else if (baud <= 1200) baud = 1200;
499 else if (baud <= 1800) baud = 1800;
500 else if (baud <= 2400) baud = 2400;
501 else if (baud <= 4000) baud = 4000;
502 else if (baud <= 4803) baud = 4800;
503 else if (baud <= 7207) baud = 7200;
504 else if (baud <= 9612) baud = 9600;
505 else if (baud <= 14428) baud = 14400;
506 else if (baud <= 16062) baud = 16000;
507 else if (baud <= 19250) baud = 19200;
508 else if (baud <= 28912) baud = 28800;
509 else if (baud <= 38601) baud = 38400;
510 else if (baud <= 51558) baud = 51200;
511 else if (baud <= 56280) baud = 56000;
512 else if (baud <= 58053) baud = 57600;
513 else if (baud <= 64111) baud = 64000;
514 else if (baud <= 77608) baud = 76800;
515 else if (baud <= 117028) baud = 115200;
516 else if (baud <= 129347) baud = 128000;
517 else if (baud <= 156868) baud = 153600;
518 else if (baud <= 237832) baud = 230400;
519 else if (baud <= 254234) baud = 250000;
520 else if (baud <= 273066) baud = 256000;
521 else if (baud <= 491520) baud = 460800;
522 else if (baud <= 567138) baud = 500000;
523 else if (baud <= 670254) baud = 576000;
524 else if (baud < 1000000)
526 else if (baud > 2000000)
531 static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
535 result = cp210x_set_config_single(port, CP210X_IFC_ENABLE,
538 dev_err(&port->dev, "%s - Unable to enable UART\n", __func__);
542 /* Configure the termios structure */
543 cp210x_get_termios(tty, port);
545 /* The baud rate must be initialised on cp2104 */
547 cp210x_change_speed(tty, port, NULL);
549 return usb_serial_generic_open(tty, port);
552 static void cp210x_close(struct usb_serial_port *port)
554 unsigned int purge_ctl;
556 usb_serial_generic_close(port);
558 /* Clear both queues; cp2108 needs this to avoid an occasional hang */
559 purge_ctl = PURGE_ALL;
560 cp210x_set_config(port, CP210X_PURGE, &purge_ctl, 2);
562 cp210x_set_config_single(port, CP210X_IFC_ENABLE, UART_DISABLE);
566 * Read how many bytes are waiting in the TX queue.
568 static int cp210x_get_tx_queue_byte_count(struct usb_serial_port *port,
571 struct usb_serial *serial = port->serial;
572 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
573 struct cp210x_comm_status *sts;
576 sts = kmalloc(sizeof(*sts), GFP_KERNEL);
580 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
581 CP210X_GET_COMM_STATUS, REQTYPE_INTERFACE_TO_HOST,
582 0, port_priv->bInterfaceNumber, sts, sizeof(*sts),
583 USB_CTRL_GET_TIMEOUT);
584 if (result == sizeof(*sts)) {
585 *count = le32_to_cpu(sts->ulAmountInOutQueue);
588 dev_err(&port->dev, "failed to get comm status: %d\n", result);
598 static bool cp210x_tx_empty(struct usb_serial_port *port)
603 err = cp210x_get_tx_queue_byte_count(port, &count);
612 * Reads the baud rate, data bits, parity, stop bits and flow control mode
613 * from the device, corrects any unsupported values, and configures the
614 * termios structure to reflect the state of the device
616 static void cp210x_get_termios(struct tty_struct *tty,
617 struct usb_serial_port *port)
622 cp210x_get_termios_port(tty->driver_data,
623 &tty->termios.c_cflag, &baud);
624 tty_encode_baud_rate(tty, baud, baud);
628 cp210x_get_termios_port(port, &cflag, &baud);
633 * cp210x_get_termios_port
634 * This is the heart of cp210x_get_termios which always uses a &usb_serial_port.
636 static void cp210x_get_termios_port(struct usb_serial_port *port,
637 unsigned int *cflagp, unsigned int *baudp)
639 struct device *dev = &port->dev;
640 unsigned int cflag, modem_ctl[4];
644 cp210x_get_config(port, CP210X_GET_BAUDRATE, &baud, 4);
646 dev_dbg(dev, "%s - baud rate = %d\n", __func__, baud);
651 cp210x_get_line_ctl(port, &bits);
653 switch (bits & BITS_DATA_MASK) {
655 dev_dbg(dev, "%s - data bits = 5\n", __func__);
659 dev_dbg(dev, "%s - data bits = 6\n", __func__);
663 dev_dbg(dev, "%s - data bits = 7\n", __func__);
667 dev_dbg(dev, "%s - data bits = 8\n", __func__);
671 dev_dbg(dev, "%s - data bits = 9 (not supported, using 8 data bits)\n", __func__);
673 bits &= ~BITS_DATA_MASK;
675 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
678 dev_dbg(dev, "%s - Unknown number of data bits, using 8\n", __func__);
680 bits &= ~BITS_DATA_MASK;
682 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
686 switch (bits & BITS_PARITY_MASK) {
687 case BITS_PARITY_NONE:
688 dev_dbg(dev, "%s - parity = NONE\n", __func__);
691 case BITS_PARITY_ODD:
692 dev_dbg(dev, "%s - parity = ODD\n", __func__);
693 cflag |= (PARENB|PARODD);
695 case BITS_PARITY_EVEN:
696 dev_dbg(dev, "%s - parity = EVEN\n", __func__);
700 case BITS_PARITY_MARK:
701 dev_dbg(dev, "%s - parity = MARK\n", __func__);
702 cflag |= (PARENB|PARODD|CMSPAR);
704 case BITS_PARITY_SPACE:
705 dev_dbg(dev, "%s - parity = SPACE\n", __func__);
707 cflag |= (PARENB|CMSPAR);
710 dev_dbg(dev, "%s - Unknown parity mode, disabling parity\n", __func__);
712 bits &= ~BITS_PARITY_MASK;
713 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
718 switch (bits & BITS_STOP_MASK) {
720 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
723 dev_dbg(dev, "%s - stop bits = 1.5 (not supported, using 1 stop bit)\n", __func__);
724 bits &= ~BITS_STOP_MASK;
725 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
728 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
732 dev_dbg(dev, "%s - Unknown number of stop bits, using 1 stop bit\n", __func__);
733 bits &= ~BITS_STOP_MASK;
734 cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2);
738 cp210x_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
739 if (modem_ctl[0] & 0x0008) {
740 dev_dbg(dev, "%s - flow control = CRTSCTS\n", __func__);
743 dev_dbg(dev, "%s - flow control = NONE\n", __func__);
751 * CP2101 supports the following baud rates:
753 * 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 14400, 19200, 28800,
754 * 38400, 56000, 57600, 115200, 128000, 230400, 460800, 921600
756 * CP2102 and CP2103 support the following additional rates:
758 * 4000, 16000, 51200, 64000, 76800, 153600, 250000, 256000, 500000,
761 * The device will map a requested rate to a supported one, but the result
762 * of requests for rates greater than 1053257 is undefined (see AN205).
764 * CP2104, CP2105 and CP2110 support most rates up to 2M, 921k and 1M baud,
765 * respectively, with an error less than 1%. The actual rates are determined
768 * div = round(freq / (2 x prescale x request))
769 * actual = freq / (2 x prescale x div)
771 * For CP2104 and CP2105 freq is 48Mhz and prescale is 4 for request <= 365bps
773 * For CP2110 freq is 24Mhz and prescale is 4 for request <= 300bps or 1
776 static void cp210x_change_speed(struct tty_struct *tty,
777 struct usb_serial_port *port, struct ktermios *old_termios)
781 baud = tty->termios.c_ospeed;
783 /* This maps the requested rate to a rate valid on cp2102 or cp2103,
784 * or to an arbitrary rate in [1M,2M].
786 * NOTE: B0 is not implemented.
788 baud = cp210x_quantise_baudrate(baud);
790 dev_dbg(&port->dev, "%s - setting baud rate to %u\n", __func__, baud);
791 if (cp210x_set_config(port, CP210X_SET_BAUDRATE, &baud,
793 dev_warn(&port->dev, "failed to set baud rate to %u\n", baud);
795 baud = old_termios->c_ospeed;
800 tty_encode_baud_rate(tty, baud, baud);
803 static void cp210x_set_termios(struct tty_struct *tty,
804 struct usb_serial_port *port, struct ktermios *old_termios)
806 struct device *dev = &port->dev;
807 unsigned int cflag, old_cflag;
809 unsigned int modem_ctl[4];
811 cflag = tty->termios.c_cflag;
812 old_cflag = old_termios->c_cflag;
814 if (tty->termios.c_ospeed != old_termios->c_ospeed)
815 cp210x_change_speed(tty, port, old_termios);
817 /* If the number of data bits is to be updated */
818 if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
819 cp210x_get_line_ctl(port, &bits);
820 bits &= ~BITS_DATA_MASK;
821 switch (cflag & CSIZE) {
824 dev_dbg(dev, "%s - data bits = 5\n", __func__);
828 dev_dbg(dev, "%s - data bits = 6\n", __func__);
832 dev_dbg(dev, "%s - data bits = 7\n", __func__);
836 dev_dbg(dev, "%s - data bits = 8\n", __func__);
840 dev_dbg(dev, "%s - data bits = 9\n", __func__);
843 dev_dbg(dev, "cp210x driver does not support the number of bits requested, using 8 bit mode\n");
847 if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
848 dev_dbg(dev, "Number of data bits requested not supported by device\n");
851 if ((cflag & (PARENB|PARODD|CMSPAR)) !=
852 (old_cflag & (PARENB|PARODD|CMSPAR))) {
853 cp210x_get_line_ctl(port, &bits);
854 bits &= ~BITS_PARITY_MASK;
855 if (cflag & PARENB) {
856 if (cflag & CMSPAR) {
857 if (cflag & PARODD) {
858 bits |= BITS_PARITY_MARK;
859 dev_dbg(dev, "%s - parity = MARK\n", __func__);
861 bits |= BITS_PARITY_SPACE;
862 dev_dbg(dev, "%s - parity = SPACE\n", __func__);
865 if (cflag & PARODD) {
866 bits |= BITS_PARITY_ODD;
867 dev_dbg(dev, "%s - parity = ODD\n", __func__);
869 bits |= BITS_PARITY_EVEN;
870 dev_dbg(dev, "%s - parity = EVEN\n", __func__);
874 if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
875 dev_dbg(dev, "Parity mode not supported by device\n");
878 if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
879 cp210x_get_line_ctl(port, &bits);
880 bits &= ~BITS_STOP_MASK;
881 if (cflag & CSTOPB) {
883 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
886 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
888 if (cp210x_set_config(port, CP210X_SET_LINE_CTL, &bits, 2))
889 dev_dbg(dev, "Number of stop bits requested not supported by device\n");
892 if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
893 cp210x_get_config(port, CP210X_GET_FLOW, modem_ctl, 16);
894 dev_dbg(dev, "%s - read modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x\n",
895 __func__, modem_ctl[0], modem_ctl[1],
896 modem_ctl[2], modem_ctl[3]);
898 if (cflag & CRTSCTS) {
899 modem_ctl[0] &= ~0x7B;
900 modem_ctl[0] |= 0x09;
902 dev_dbg(dev, "%s - flow control = CRTSCTS\n", __func__);
904 modem_ctl[0] &= ~0x7B;
905 modem_ctl[0] |= 0x01;
906 modem_ctl[1] |= 0x40;
907 dev_dbg(dev, "%s - flow control = NONE\n", __func__);
910 dev_dbg(dev, "%s - write modem controls = 0x%.4x 0x%.4x 0x%.4x 0x%.4x\n",
911 __func__, modem_ctl[0], modem_ctl[1],
912 modem_ctl[2], modem_ctl[3]);
913 cp210x_set_config(port, CP210X_SET_FLOW, modem_ctl, 16);
918 static int cp210x_tiocmset(struct tty_struct *tty,
919 unsigned int set, unsigned int clear)
921 struct usb_serial_port *port = tty->driver_data;
922 return cp210x_tiocmset_port(port, set, clear);
925 static int cp210x_tiocmset_port(struct usb_serial_port *port,
926 unsigned int set, unsigned int clear)
928 unsigned int control = 0;
930 if (set & TIOCM_RTS) {
931 control |= CONTROL_RTS;
932 control |= CONTROL_WRITE_RTS;
934 if (set & TIOCM_DTR) {
935 control |= CONTROL_DTR;
936 control |= CONTROL_WRITE_DTR;
938 if (clear & TIOCM_RTS) {
939 control &= ~CONTROL_RTS;
940 control |= CONTROL_WRITE_RTS;
942 if (clear & TIOCM_DTR) {
943 control &= ~CONTROL_DTR;
944 control |= CONTROL_WRITE_DTR;
947 dev_dbg(&port->dev, "%s - control = 0x%.4x\n", __func__, control);
949 return cp210x_set_config(port, CP210X_SET_MHS, &control, 2);
952 static void cp210x_dtr_rts(struct usb_serial_port *p, int on)
955 cp210x_tiocmset_port(p, TIOCM_DTR|TIOCM_RTS, 0);
957 cp210x_tiocmset_port(p, 0, TIOCM_DTR|TIOCM_RTS);
960 static int cp210x_tiocmget(struct tty_struct *tty)
962 struct usb_serial_port *port = tty->driver_data;
963 unsigned int control;
966 cp210x_get_config(port, CP210X_GET_MDMSTS, &control, 1);
968 result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
969 |((control & CONTROL_RTS) ? TIOCM_RTS : 0)
970 |((control & CONTROL_CTS) ? TIOCM_CTS : 0)
971 |((control & CONTROL_DSR) ? TIOCM_DSR : 0)
972 |((control & CONTROL_RING)? TIOCM_RI : 0)
973 |((control & CONTROL_DCD) ? TIOCM_CD : 0);
975 dev_dbg(&port->dev, "%s - control = 0x%.2x\n", __func__, control);
980 static void cp210x_break_ctl(struct tty_struct *tty, int break_state)
982 struct usb_serial_port *port = tty->driver_data;
985 if (break_state == 0)
989 dev_dbg(&port->dev, "%s - turning break %s\n", __func__,
990 state == BREAK_OFF ? "off" : "on");
991 cp210x_set_config(port, CP210X_SET_BREAK, &state, 2);
994 static int cp210x_port_probe(struct usb_serial_port *port)
996 struct usb_serial *serial = port->serial;
997 struct usb_host_interface *cur_altsetting;
998 struct cp210x_port_private *port_priv;
1001 port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
1005 cur_altsetting = serial->interface->cur_altsetting;
1006 port_priv->bInterfaceNumber = cur_altsetting->desc.bInterfaceNumber;
1008 usb_set_serial_port_data(port, port_priv);
1010 ret = cp210x_detect_swapped_line_ctl(port);
1019 static int cp210x_port_remove(struct usb_serial_port *port)
1021 struct cp210x_port_private *port_priv;
1023 port_priv = usb_get_serial_port_data(port);
1029 module_usb_serial_driver(serial_drivers, id_table);
1031 MODULE_DESCRIPTION(DRIVER_DESC);
1032 MODULE_LICENSE("GPL");