status = "okay";
};
- spi0: spi@10600 {
- pinctrl-0 = <&spi0_pins2>;
- pinctrl-names = "default";
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "mx25l25635e", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <50000000>;
- };
- };
-
nand@d0000 {
status = "okay";
num-cs = <1>;
compatible = "linux,spdif-dir";
};
};
+
+&spi0 {
+ pinctrl-0 = <&spi0_pins2>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mx25l25635e", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ };
+};
+
phy-mode = "rgmii-id";
};
- spi@10600 {
- status = "okay";
- pinctrl-0 = <&spi0_pins2>;
- pinctrl-names = "default";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- /* MX25L8006E */
- compatible = "mxicy,mx25l8005", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <50000000>;
-
- partition@0 {
- label = "u-boot";
- reg = <0x0 0x100000>;
- };
- };
- };
-
usb@50000 {
status = "okay";
};
marvell,function = "gpio";
};
};
+
+&spi0 {
+ status = "okay";
+ pinctrl-0 = <&spi0_pins2>;
+ pinctrl-names = "default";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ /* MX25L8006E */
+ compatible = "mxicy,mx25l8005", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x100000>;
+ };
+ };
+};
status = "disabled";
};
- spi0: spi@10600 {
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "micron,n25q064", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <20000000>;
-
- /*
- * Warning!
- *
- * Synology u-boot uses its compiled-in environment
- * and it seems Synology did not care to change u-boot
- * default configuration in order to allow saving a
- * modified environment at a sensible location. So,
- * if you do a 'saveenv' under u-boot, your modified
- * environment will be saved at 1MB after the start
- * of the flash, i.e. in the middle of the uImage.
- * For that reason, it is strongly advised not to
- * change the default environment, unless you know
- * what you are doing.
- */
- partition@00000000 { /* u-boot */
- label = "RedBoot";
- reg = <0x00000000 0x000c0000>; /* 768KB */
- };
-
- partition@000c0000 { /* uImage */
- label = "zImage";
- reg = <0x000c0000 0x002d0000>; /* 2880KB */
- };
-
- partition@00390000 { /* uInitramfs */
- label = "rd.gz";
- reg = <0x00390000 0x00440000>; /* 4250KB */
- };
-
- partition@007d0000 { /* MAC address and serial number */
- label = "vendor";
- reg = <0x007d0000 0x00010000>; /* 64KB */
- };
-
- partition@007e0000 {
- label = "RedBoot config";
- reg = <0x007e0000 0x00010000>; /* 64KB */
- };
-
- partition@007f0000 {
- label = "FIS directory";
- reg = <0x007f0000 0x00010000>; /* 64KB */
- };
- };
- };
-
i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
pinctrl-0 = <&i2c0_pins>;
marvell,function = "gpio";
};
};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q064", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+
+ /*
+ * Warning!
+ *
+ * Synology u-boot uses its compiled-in environment
+ * and it seems Synology did not care to change u-boot
+ * default configuration in order to allow saving a
+ * modified environment at a sensible location. So,
+ * if you do a 'saveenv' under u-boot, your modified
+ * environment will be saved at 1MB after the start
+ * of the flash, i.e. in the middle of the uImage.
+ * For that reason, it is strongly advised not to
+ * change the default environment, unless you know
+ * what you are doing.
+ */
+ partition@00000000 { /* u-boot */
+ label = "RedBoot";
+ reg = <0x00000000 0x000c0000>; /* 768KB */
+ };
+
+ partition@000c0000 { /* uImage */
+ label = "zImage";
+ reg = <0x000c0000 0x002d0000>; /* 2880KB */
+ };
+
+ partition@00390000 { /* uInitramfs */
+ label = "rd.gz";
+ reg = <0x00390000 0x00440000>; /* 4250KB */
+ };
+
+ partition@007d0000 { /* MAC address and serial number */
+ label = "vendor";
+ reg = <0x007d0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007e0000 {
+ label = "RedBoot config";
+ reg = <0x007e0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007f0000 {
+ label = "FIS directory";
+ reg = <0x007f0000 0x00010000>; /* 64KB */
+ };
+ };
+};
interrupts = <50>;
};
- spi0: spi@10600 {
- reg = <0x10600 0x28>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- interrupts = <30>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- spi1: spi@10680 {
- reg = <0x10680 0x28>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- interrupts = <92>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
i2c0: i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
#address-cells = <1>;
status = "disabled";
};
};
+
+ spi0: spi@10600 {
+ reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <30>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ spi1: spi@10680 {
+ reg = <MBUS_ID(0xf0, 0x01) 0x10680 0x28>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <92>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
};
clocks {
wt-override;
};
- /*
- * Default SPI pinctrl setting, can be overwritten on
- * board level if a different configuration is used.
- */
- spi0: spi@10600 {
- compatible = "marvell,armada-370-spi",
- "marvell,orion-spi";
- pinctrl-0 = <&spi0_pins1>;
- pinctrl-names = "default";
- };
-
- spi1: spi@10680 {
- compatible = "marvell,armada-370-spi",
- "marvell,orion-spi";
- pinctrl-0 = <&spi1_pins>;
- pinctrl-names = "default";
- };
-
i2c0: i2c@11000 {
reg = <0x11000 0x20>;
};
marvell,function = "ge1";
};
};
+
+/*
+ * Default SPI pinctrl setting, can be overwritten on
+ * board level if a different configuration is used.
+ */
+&spi0 {
+ compatible = "marvell,armada-370-spi", "marvell,orion-spi";
+ pinctrl-0 = <&spi0_pins1>;
+ pinctrl-names = "default";
+};
+
+&spi1 {
+ compatible = "marvell,armada-370-spi", "marvell,orion-spi";
+ pinctrl-0 = <&spi1_pins>;
+ pinctrl-names = "default";
+};
MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
internal-regs {
- spi1: spi@10680 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "st,m25p128", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <54000000>;
- };
- };
-
i2c0: i2c@11000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
};
};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <54000000>;
+ };
+};
MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
internal-regs {
-
- spi@10600 {
- status = "disabled";
- };
-
i2c@11000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
marvell,function = "gpio";
};
};
+
+&spi0 {
+ status = "disabled";
+};
status = "okay";
};
- spi@10680 {
- /*
- * We don't seem to have the W25Q32 on the
- * A1 Rev 2.0 boards, so disable SPI.
- * CS0: W25Q32 (doesn't appear to be present)
- * CS1:
- * CS2: mikrobus
- */
- pinctrl-0 = <&spi1_pins
- &clearfog_spi1_cs_pins
- &mikro_spi_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "w25q32", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <3000000>;
- status = "disabled";
- };
- };
-
usb@58000 {
/* CON3, nearest power. */
status = "okay";
};
};
};
+
+&spi1 {
+ /*
+ * We don't seem to have the W25Q32 on the
+ * A1 Rev 2.0 boards, so disable SPI.
+ * CS0: W25Q32 (doesn't appear to be present)
+ * CS1:
+ * CS2: mikrobus
+ */
+ pinctrl-0 = <&spi1_pins
+ &clearfog_spi1_cs_pins
+ &mikro_spi_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "w25q32", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <3000000>;
+ status = "disabled";
+ };
+};
MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
internal-regs {
- spi@10600 {
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "w25q32", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- };
- };
-
i2c@11000 {
status = "okay";
clock-frequency = <100000>;
};
};
};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "w25q32", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
+};
+
MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
internal-regs {
- spi@10600 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "st,m25p128", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <50000000>;
- m25p,fast-read;
- };
- };
-
i2c@11000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
marvell,function = "gpio";
};
};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+ };
+};
MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
internal-regs {
- spi@10600 {
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "st,m25p128", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- };
- };
-
i2c@11000 {
status = "okay";
clock-frequency = <100000>;
};
};
};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
+};
+
<0xc100 0x100>;
};
- spi0: spi@10600 {
- compatible = "marvell,armada-380-spi",
- "marvell,orion-spi";
- reg = <0x10600 0x50>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- spi1: spi@10680 {
- compatible = "marvell,armada-380-spi",
- "marvell,orion-spi";
- reg = <0x10680 0x50>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
i2c0: i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
no-memory-wc;
status = "disabled";
};
+
+ spi0: spi@10600 {
+ compatible = "marvell,armada-380-spi",
+ "marvell,orion-spi";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ spi1: spi@10680 {
+ compatible = "marvell,armada-380-spi",
+ "marvell,orion-spi";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10680 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
};
clocks {
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
internal-regs {
- spi@10680 {
- status = "okay";
- pinctrl-0 = <&spi1_pins>;
- pinctrl-names = "default";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "n25q128a13", "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <108000000>;
-
- partition@0 {
- label = "U-Boot";
- reg = <0 0x400000>;
- };
-
- partition@400000 {
- label = "Filesystem";
- reg = <0x400000 0x1000000>;
- };
- };
- };
-
i2c@11000 {
pinctrl-0 = <&i2c0_pins>;
pinctrl-names = "default";
};
};
};
+
+&spi1 {
+ status = "okay";
+ pinctrl-0 = <&spi1_pins>;
+ pinctrl-names = "default";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <108000000>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x400000>;
+ };
+
+ partition@400000 {
+ label = "Filesystem";
+ reg = <0x400000 0x1000000>;
+ };
+ };
+};
<0xc100 0x100>;
};
- spi0: spi@10600 {
- compatible = "marvell,armada-390-spi",
- "marvell,orion-spi";
- reg = <0x10600 0x50>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <0>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
- spi1: spi@10680 {
- compatible = "marvell,armada-390-spi",
- "marvell,orion-spi";
- reg = <0x10680 0x50>;
- #address-cells = <1>;
- #size-cells = <0>;
- cell-index = <1>;
- interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&coreclk 0>;
- status = "disabled";
- };
-
i2c0: i2c@11000 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
status = "disabled";
};
};
+
+ spi0: spi@10600 {
+ compatible = "marvell,armada-390-spi",
+ "marvell,orion-spi";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10600 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ spi1: spi@10680 {
+ compatible = "marvell,armada-390-spi",
+ "marvell,orion-spi";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10680 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
};
clocks {
phy = <&phy1>;
phy-mode = "rgmii-id";
};
-
- spi0: spi@10600 {
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "n25q128a13", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- };
- };
};
};
marvell,function = "gpio";
};
};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
+};
status = "okay";
};
- spi0: spi@10600 {
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "m25p64", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <20000000>;
- };
- };
-
nand@d0000 {
status = "okay";
num-cs = <1>;
};
};
};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ };
+};
status = "okay";
};
- spi0: spi@10600 {
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "n25q128a13", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- };
- };
-
bm@c0000 {
status = "okay";
};
};
};
};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
+};
reg = <0x180000 0x780000>; /* 7.5MB */
};
};
-
- spi0: spi@10600 {
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "everspin,mr25h256";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <40000000>;
- };
- };
};
};
marvell,function = "gpio";
};
};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "everspin,mr25h256";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <40000000>;
+ };
+};
status = "disabled";
};
- spi0: spi@10600 {
- status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "micron,n25q064", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <20000000>;
-
- /*
- * Warning!
- *
- * Synology u-boot uses its compiled-in environment
- * and it seems Synology did not care to change u-boot
- * default configuration in order to allow saving a
- * modified environment at a sensible location. So,
- * if you do a 'saveenv' under u-boot, your modified
- * environment will be saved at 1MB after the start
- * of the flash, i.e. in the middle of the uImage.
- * For that reason, it is strongly advised not to
- * change the default environment, unless you know
- * what you are doing.
- */
- partition@00000000 { /* u-boot */
- label = "RedBoot";
- reg = <0x00000000 0x000d0000>; /* 832KB */
- };
-
- partition@000c0000 { /* uImage */
- label = "zImage";
- reg = <0x000d0000 0x002d0000>; /* 2880KB */
- };
-
- partition@003a0000 { /* uInitramfs */
- label = "rd.gz";
- reg = <0x003a0000 0x00430000>; /* 4250KB */
- };
-
- partition@007d0000 { /* MAC address and serial number */
- label = "vendor";
- reg = <0x007d0000 0x00010000>; /* 64KB */
- };
-
- partition@007e0000 {
- label = "RedBoot config";
- reg = <0x007e0000 0x00010000>; /* 64KB */
- };
-
- partition@007f0000 {
- label = "FIS directory";
- reg = <0x007f0000 0x00010000>; /* 64KB */
- };
- };
- };
-
i2c@11000 {
clock-frequency = <400000>;
status = "okay";
marvell,function = "gpio";
};
};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q064", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+
+ /*
+ * Warning!
+ *
+ * Synology u-boot uses its compiled-in environment
+ * and it seems Synology did not care to change u-boot
+ * default configuration in order to allow saving a
+ * modified environment at a sensible location. So,
+ * if you do a 'saveenv' under u-boot, your modified
+ * environment will be saved at 1MB after the start
+ * of the flash, i.e. in the middle of the uImage.
+ * For that reason, it is strongly advised not to
+ * change the default environment, unless you know
+ * what you are doing.
+ */
+ partition@00000000 { /* u-boot */
+ label = "RedBoot";
+ reg = <0x00000000 0x000d0000>; /* 832KB */
+ };
+
+ partition@000c0000 { /* uImage */
+ label = "zImage";
+ reg = <0x000d0000 0x002d0000>; /* 2880KB */
+ };
+
+ partition@003a0000 { /* uInitramfs */
+ label = "rd.gz";
+ reg = <0x003a0000 0x00430000>; /* 4250KB */
+ };
+
+ partition@007d0000 { /* MAC address and serial number */
+ label = "vendor";
+ reg = <0x007d0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007e0000 {
+ label = "RedBoot config";
+ reg = <0x007e0000 0x00010000>; /* 64KB */
+ };
+
+ partition@007f0000 {
+ label = "FIS directory";
+ reg = <0x007f0000 0x00010000>; /* 64KB */
+ };
+ };
+};
wt-override;
};
- spi0: spi@10600 {
- compatible = "marvell,armada-xp-spi",
- "marvell,orion-spi";
- pinctrl-0 = <&spi0_pins>;
- pinctrl-names = "default";
- };
-
- spi1: spi@10680 {
- compatible = "marvell,armada-xp-spi",
- "marvell,orion-spi";
- pinctrl-0 = <&spi1_pins>;
- pinctrl-names = "default";
- };
-
-
i2c0: i2c@11000 {
compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
reg = <0x11000 0x100>;
marvell,function = "uart3";
};
};
+
+&spi0 {
+ compatible = "marvell,armada-xp-spi", "marvell,orion-spi";
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+};
+
+&spi1 {
+ compatible = "marvell,armada-xp-spi", "marvell,orion-spi";
+ pinctrl-0 = <&spi1_pins>;
+ pinctrl-names = "default";
+};
projects / cascardo / linux.git / commitdiff