e100: Support RXALL feature flag.

This allows the NIC to receive packets with bad FCS
and other errors.  Good for sniffing packets on flakey
networks.

v4:  Only flax rx-over-length errors if pkt is beyond
   maximum expected packet size, not just beyond the MTU.
   This matches the existing logic for this counter.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

diff --git a/drivers/net/ethernet/intel/e100.c b/drivers/net/ethernet/intel/e100.c
index 6f9f70a..4d8a616 100644 (file)
--- a/drivers/net/ethernet/intel/e100.c
+++ b/drivers/net/ethernet/intel/e100.c
@@ -462,7 +462,7 @@ struct config {
 /*5*/  u8 X(tx_dma_max_count:7, dma_max_count_enable:1);
 /*6*/  u8 X(X(X(X(X(X(X(late_scb_update:1, direct_rx_dma:1),
           tno_intr:1), cna_intr:1), standard_tcb:1), standard_stat_counter:1),
-          rx_discard_overruns:1), rx_save_bad_frames:1);
+          rx_save_overruns : 1), rx_save_bad_frames : 1);
 /*7*/  u8 X(X(X(X(X(rx_discard_short_frames:1, tx_underrun_retry:2),
           pad7:2), rx_extended_rfd:1), tx_two_frames_in_fifo:1),
           tx_dynamic_tbd:1);
@@ -1165,6 +1165,12 @@ static void e100_configure(struct nic *nic, struct cb *cb, struct sk_buff *skb)
                }
        }
 
+       if (netdev->features & NETIF_F_RXALL) {
+               config->rx_save_overruns = 0x1; /* 1=save, 0=discard */
+               config->rx_save_bad_frames = 0x1;       /* 1=save, 0=discard */
+               config->rx_discard_short_frames = 0x0;  /* 1=discard, 0=save */
+       }
+
        netif_printk(nic, hw, KERN_DEBUG, nic->netdev,
                     "[00-07]=%02X:%02X:%02X:%02X:%02X:%02X:%02X:%02X\n",
                     c[0], c[1], c[2], c[3], c[4], c[5], c[6], c[7]);
@@ -1999,6 +2005,16 @@ static int e100_rx_indicate(struct nic *nic, struct rx *rx,
        skb_put(skb, actual_size);
        skb->protocol = eth_type_trans(skb, nic->netdev);
 
+       /* If we are receiving all frames, then don't bother
+        * checking for errors.
+        */
+       if (unlikely(dev->features & NETIF_F_RXALL)) {
+               if (actual_size > ETH_DATA_LEN + VLAN_ETH_HLEN + fcs_pad)
+                       /* Received oversized frame, but keep it. */
+                       nic->rx_over_length_errors++;
+               goto process_skb;
+       }
+
        if (unlikely(!(rfd_status & cb_ok))) {
                /* Don't indicate if hardware indicates errors */
                dev_kfree_skb_any(skb);
@@ -2007,6 +2023,7 @@ static int e100_rx_indicate(struct nic *nic, struct rx *rx,
                nic->rx_over_length_errors++;
                dev_kfree_skb_any(skb);
        } else {
+process_skb:
                dev->stats.rx_packets++;
                dev->stats.rx_bytes += (actual_size - fcs_pad);
                netif_receive_skb(skb);
@@ -2758,7 +2775,7 @@ static int e100_set_features(struct net_device *netdev,
        struct nic *nic = netdev_priv(netdev);
        netdev_features_t changed = features ^ netdev->features;
 
-       if (!(changed & (NETIF_F_RXFCS)))
+       if (!(changed & (NETIF_F_RXFCS | NETIF_F_RXALL)))
                return 0;
 
        netdev->features = features;
@@ -2794,6 +2811,7 @@ static int __devinit e100_probe(struct pci_dev *pdev,
 
        netdev->hw_features |= NETIF_F_RXFCS;
        netdev->priv_flags |= IFF_SUPP_NOFCS;
+       netdev->hw_features |= NETIF_F_RXALL;
 
        netdev->netdev_ops = &e100_netdev_ops;
        SET_ETHTOOL_OPS(netdev, &e100_ethtool_ops);