[media] drxk_hard: don't split strings across lines

X-Patchwork-Delegate: mchehab@redhat.com
WARNING: quoted string split across lines
	#5416: FILE: media/dvb-frontends/drxk_hard.c:5416:
	+		dprintk(1, "Could not set demodulator parameters. Make "
	+			"sure qam_demod_parameter_count (%d) is correct for "
	WARNING: quoted string split across lines
	#5423: FILE: media/dvb-frontends/drxk_hard.c:5423:
	+		dprintk(1, "Auto-probing the correct QAM demodulator command "
	+			"parameters was successful - using %d parameters.\n",

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

diff --git a/drivers/media/dvb-frontends/drxk_hard.c b/drivers/media/dvb-frontends/drxk_hard.c
index 552bce5..fdbe23a 100644 (file)
--- a/drivers/media/dvb-frontends/drxk_hard.c
+++ b/drivers/media/dvb-frontends/drxk_hard.c
@@ -168,7 +168,7 @@ MODULE_PARM_DESC(debug, "enable debug messages");
 
 #define dprintk(level, fmt, arg...) do {                       \
 if (debug >= level)                                            \
-       printk(KERN_DEBUG "drxk: %s" fmt, __func__, ## arg);    \
+       pr_debug(fmt, ##arg);                                   \
 } while (0)
 
 
@@ -258,8 +258,8 @@ static int i2c_write(struct drxk_state *state, u8 adr, u8 *data, int len)
        if (debug > 2) {
                int i;
                for (i = 0; i < len; i++)
-                       printk(KERN_CONT " %02x", data[i]);
-               printk(KERN_CONT "\n");
+                       pr_cont(" %02x", data[i]);
+               pr_cont("\n");
        }
        status = drxk_i2c_transfer(state, &msg, 1);
        if (status >= 0 && status != 1)
@@ -285,7 +285,7 @@ static int i2c_read(struct drxk_state *state,
        status = drxk_i2c_transfer(state, msgs, 2);
        if (status != 2) {
                if (debug > 2)
-                       printk(KERN_CONT ": ERROR!\n");
+                       pr_cont(": ERROR!\n");
                if (status >= 0)
                        status = -EIO;
 
@@ -296,11 +296,11 @@ static int i2c_read(struct drxk_state *state,
                int i;
                dprintk(2, ": read from");
                for (i = 0; i < len; i++)
-                       printk(KERN_CONT " %02x", msg[i]);
-               printk(KERN_CONT ", value = ");
+                       pr_cont(" %02x", msg[i]);
+               pr_cont(", value = ");
                for (i = 0; i < alen; i++)
-                       printk(KERN_CONT " %02x", answ[i]);
-               printk(KERN_CONT "\n");
+                       pr_cont(" %02x", answ[i]);
+               pr_cont("\n");
        }
        return 0;
 }
@@ -470,8 +470,8 @@ static int write_block(struct drxk_state *state, u32 address,
                        int i;
                        if (p_block)
                                for (i = 0; i < chunk; i++)
-                                       printk(KERN_CONT " %02x", p_block[i]);
-                       printk(KERN_CONT "\n");
+                                       pr_cont(" %02x", p_block[i]);
+                       pr_cont("\n");
                }
                status = i2c_write(state, state->demod_address,
                                   &state->chunk[0], chunk + adr_length);
@@ -5412,15 +5412,15 @@ static int set_qam(struct drxk_state *state, u16 intermediate_freqk_hz,
        }
 
        if (status < 0) {
-               dprintk(1, "Could not set demodulator parameters. Make "
-                       "sure qam_demod_parameter_count (%d) is correct for "
-                       "your firmware (%s).\n",
+               dprintk(1, "Could not set demodulator parameters.\n");
+               dprintk(1,
+                       "Make sure qam_demod_parameter_count (%d) is correct for your firmware (%s).\n",
                        state->qam_demod_parameter_count,
                        state->microcode_name);
                goto error;
        } else if (!state->qam_demod_parameter_count) {
-               dprintk(1, "Auto-probing the correct QAM demodulator command "
-                       "parameters was successful - using %d parameters.\n",
+               dprintk(1,
+                       "Auto-probing the QAM command parameters was successful - using %d parameters.\n",
                        qam_demod_param_count);
 
                /*