+++ /dev/null
-i2c Controller on ARM Versatile platform:
-
-Required properties:
-- compatible : Must be "arm,versatile-i2c";
-- reg
-- #address-cells = <1>;
-- #size-cells = <0>;
-
-Optional properties:
-- Child nodes conforming to i2c bus binding
+++ /dev/null
-I2C for Atmel platforms
-
-Required properties :
-- compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c",
- "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c"
- or "atmel,at91sam9x5-i2c"
-- reg: physical base address of the controller and length of memory mapped
- region.
-- interrupts: interrupt number to the cpu.
-- #address-cells = <1>;
-- #size-cells = <0>;
-
-Optional properties:
-- Child nodes conforming to i2c bus binding
-
-Examples :
-
-i2c0: i2c@fff84000 {
- compatible = "atmel,at91sam9g20-i2c";
- reg = <0xfff84000 0x100>;
- interrupts = <12 4 6>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- 24c512@50 {
- compatible = "24c512";
- reg = <0x50>;
- pagesize = <128>;
- }
-}
+++ /dev/null
-* Two Wire Serial Interface (TWSI) / I2C
-
-- compatible: "cavium,octeon-3860-twsi"
-
- Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
-
-- reg: The base address of the TWSI/I2C bus controller register bank.
-
-- #address-cells: Must be <1>.
-
-- #size-cells: Must be <0>. I2C addresses have no size component.
-
-- interrupts: A single interrupt specifier.
-
-- clock-frequency: The I2C bus clock rate in Hz.
-
-Example:
- twsi0: i2c@1180000001000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "cavium,octeon-3860-twsi";
- reg = <0x11800 0x00001000 0x0 0x200>;
- interrupts = <0 45>;
- clock-frequency = <100000>;
-
- rtc@68 {
- compatible = "dallas,ds1337";
- reg = <0x68>;
- };
- tmp@4c {
- compatible = "ti,tmp421";
- reg = <0x4c>;
- };
- };
+++ /dev/null
-CE4100 I2C
-----------
-
-CE4100 has one PCI device which is described as the I2C-Controller. This
-PCI device has three PCI-bars, each bar contains a complete I2C
-controller. So we have a total of three independent I2C-Controllers
-which share only an interrupt line.
-The driver is probed via the PCI-ID and is gathering the information of
-attached devices from the devices tree.
-Grant Likely recommended to use the ranges property to map the PCI-Bar
-number to its physical address and to use this to find the child nodes
-of the specific I2C controller. This were his exact words:
-
- Here's where the magic happens. Each entry in
- ranges describes how the parent pci address space
- (middle group of 3) is translated to the local
- address space (first group of 2) and the size of
- each range (last cell). In this particular case,
- the first cell of the local address is chosen to be
- 1:1 mapped to the BARs, and the second is the
- offset from be base of the BAR (which would be
- non-zero if you had 2 or more devices mapped off
- the same BAR)
-
- ranges allows the address mapping to be described
- in a way that the OS can interpret without
- requiring custom device driver code.
-
-This is an example which is used on FalconFalls:
-------------------------------------------------
- i2c-controller@b,2 {
- #address-cells = <2>;
- #size-cells = <1>;
- compatible = "pci8086,2e68.2",
- "pci8086,2e68",
- "pciclass,ff0000",
- "pciclass,ff00";
-
- reg = <0x15a00 0x0 0x0 0x0 0x0>;
- interrupts = <16 1>;
-
- /* as described by Grant, the first number in the group of
- * three is the bar number followed by the 64bit bar address
- * followed by size of the mapping. The bar address
- * requires also a valid translation in parents ranges
- * property.
- */
- ranges = <0 0 0x02000000 0 0xdffe0500 0x100
- 1 0 0x02000000 0 0xdffe0600 0x100
- 2 0 0x02000000 0 0xdffe0700 0x100>;
-
- i2c@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "intel,ce4100-i2c-controller";
-
- /* The first number in the reg property is the
- * number of the bar
- */
- reg = <0 0 0x100>;
-
- /* This I2C controller has no devices */
- };
-
- i2c@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "intel,ce4100-i2c-controller";
- reg = <1 0 0x100>;
-
- /* This I2C controller has one gpio controller */
- gpio@26 {
- #gpio-cells = <2>;
- compatible = "ti,pcf8575";
- reg = <0x26>;
- gpio-controller;
- };
- };
-
- i2c@2 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "intel,ce4100-i2c-controller";
- reg = <2 0 0x100>;
-
- gpio@26 {
- #gpio-cells = <2>;
- compatible = "ti,pcf8575";
- reg = <0x26>;
- gpio-controller;
- };
- };
- };
+++ /dev/null
-* Texas Instruments Davinci I2C
-
-This file provides information, what the device node for the
-davinci i2c interface contain.
-
-Required properties:
-- compatible: "ti,davinci-i2c";
-- reg : Offset and length of the register set for the device
-
-Recommended properties :
-- interrupts : standard interrupt property.
-- clock-frequency : desired I2C bus clock frequency in Hz.
-
-Example (enbw_cmc board):
- i2c@1c22000 {
- compatible = "ti,davinci-i2c";
- reg = <0x22000 0x1000>;
- clock-frequency = <100000>;
- interrupts = <15>;
- interrupt-parent = <&intc>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- dtt@48 {
- compatible = "national,lm75";
- reg = <0x48>;
- };
- };
+++ /dev/null
-* I2C
-
-Required properties :
-
- - reg : Offset and length of the register set for the device
- - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a
- compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121,
- mpc5200 or mpc5200b. For the mpc5121, an additional node
- "fsl,mpc5121-i2c-ctrl" is required as shown in the example below.
-
-Recommended properties :
-
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - fsl,preserve-clocking : boolean; if defined, the clock settings
- from the bootloader are preserved (not touched).
- - clock-frequency : desired I2C bus clock frequency in Hz.
- - fsl,timeout : I2C bus timeout in microseconds.
-
-Examples :
-
- /* MPC5121 based board */
- i2c@1740 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5121-i2c", "fsl-i2c";
- reg = <0x1740 0x20>;
- interrupts = <11 0x8>;
- interrupt-parent = <&ipic>;
- clock-frequency = <100000>;
- };
-
- i2ccontrol@1760 {
- compatible = "fsl,mpc5121-i2c-ctrl";
- reg = <0x1760 0x8>;
- };
-
- /* MPC5200B based board */
- i2c@3d00 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
- reg = <0x3d00 0x40>;
- interrupts = <2 15 0>;
- interrupt-parent = <&mpc5200_pic>;
- fsl,preserve-clocking;
- };
-
- /* MPC8544 base board */
- i2c@3100 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc8544-i2c", "fsl-i2c";
- reg = <0x3100 0x100>;
- interrupts = <43 2>;
- interrupt-parent = <&mpic>;
- clock-frequency = <400000>;
- fsl,timeout = <10000>;
- };
+++ /dev/null
-* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX
-
-Required properties:
-- compatible : Should be "fsl,<chip>-i2c"
-- reg : Should contain I2C/HS-I2C registers location and length
-- interrupts : Should contain I2C/HS-I2C interrupt
-
-Optional properties:
-- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
- The absence of the propoerty indicates the default frequency 100 kHz.
-
-Examples:
-
-i2c@83fc4000 { /* I2C2 on i.MX51 */
- compatible = "fsl,imx51-i2c", "fsl,imx1-i2c";
- reg = <0x83fc4000 0x4000>;
- interrupts = <63>;
-};
-
-i2c@70038000 { /* HS-I2C on i.MX51 */
- compatible = "fsl,imx51-i2c", "fsl,imx1-i2c";
- reg = <0x70038000 0x4000>;
- interrupts = <64>;
- clock-frequency = <400000>;
-};
+++ /dev/null
-Device-Tree bindings for i2c gpio driver
-
-Required properties:
- - compatible = "i2c-gpio";
- - gpios: sda and scl gpio
-
-
-Optional properties:
- - i2c-gpio,sda-open-drain: sda as open drain
- - i2c-gpio,scl-open-drain: scl as open drain
- - i2c-gpio,scl-output-only: scl as output only
- - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform)
- - i2c-gpio,timeout-ms: timeout to get data
-
-Example nodes:
-
-i2c@0 {
- compatible = "i2c-gpio";
- gpios = <&pioA 23 0 /* sda */
- &pioA 24 0 /* scl */
- >;
- i2c-gpio,sda-open-drain;
- i2c-gpio,scl-open-drain;
- i2c-gpio,delay-us = <2>; /* ~100 kHz */
- #address-cells = <1>;
- #size-cells = <0>;
-
- rv3029c2@56 {
- compatible = "rv3029c2";
- reg = <0x56>;
- };
-};
--- /dev/null
+I2C for Atmel platforms
+
+Required properties :
+- compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c",
+ "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c"
+ or "atmel,at91sam9x5-i2c"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: interrupt number to the cpu.
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Examples :
+
+i2c0: i2c@fff84000 {
+ compatible = "atmel,at91sam9g20-i2c";
+ reg = <0xfff84000 0x100>;
+ interrupts = <12 4 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ 24c512@50 {
+ compatible = "24c512";
+ reg = <0x50>;
+ pagesize = <128>;
+ }
+}
--- /dev/null
+* Texas Instruments Davinci I2C
+
+This file provides information, what the device node for the
+davinci i2c interface contain.
+
+Required properties:
+- compatible: "ti,davinci-i2c";
+- reg : Offset and length of the register set for the device
+
+Recommended properties :
+- interrupts : standard interrupt property.
+- clock-frequency : desired I2C bus clock frequency in Hz.
+
+Example (enbw_cmc board):
+ i2c@1c22000 {
+ compatible = "ti,davinci-i2c";
+ reg = <0x22000 0x1000>;
+ clock-frequency = <100000>;
+ interrupts = <15>;
+ interrupt-parent = <&intc>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dtt@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+ };
--- /dev/null
+Device-Tree bindings for i2c gpio driver
+
+Required properties:
+ - compatible = "i2c-gpio";
+ - gpios: sda and scl gpio
+
+
+Optional properties:
+ - i2c-gpio,sda-open-drain: sda as open drain
+ - i2c-gpio,scl-open-drain: scl as open drain
+ - i2c-gpio,scl-output-only: scl as output only
+ - i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform)
+ - i2c-gpio,timeout-ms: timeout to get data
+
+Example nodes:
+
+i2c@0 {
+ compatible = "i2c-gpio";
+ gpios = <&pioA 23 0 /* sda */
+ &pioA 24 0 /* scl */
+ >;
+ i2c-gpio,sda-open-drain;
+ i2c-gpio,scl-open-drain;
+ i2c-gpio,delay-us = <2>; /* ~100 kHz */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rv3029c2@56 {
+ compatible = "rv3029c2";
+ reg = <0x56>;
+ };
+};
--- /dev/null
+* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX
+
+Required properties:
+- compatible : Should be "fsl,<chip>-i2c"
+- reg : Should contain I2C/HS-I2C registers location and length
+- interrupts : Should contain I2C/HS-I2C interrupt
+
+Optional properties:
+- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
+ The absence of the propoerty indicates the default frequency 100 kHz.
+
+Examples:
+
+i2c@83fc4000 { /* I2C2 on i.MX51 */
+ compatible = "fsl,imx51-i2c", "fsl,imx1-i2c";
+ reg = <0x83fc4000 0x4000>;
+ interrupts = <63>;
+};
+
+i2c@70038000 { /* HS-I2C on i.MX51 */
+ compatible = "fsl,imx51-i2c", "fsl,imx1-i2c";
+ reg = <0x70038000 0x4000>;
+ interrupts = <64>;
+ clock-frequency = <400000>;
+};
--- /dev/null
+* I2C
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a
+ compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121,
+ mpc5200 or mpc5200b. For the mpc5121, an additional node
+ "fsl,mpc5121-i2c-ctrl" is required as shown in the example below.
+
+Recommended properties :
+
+ - interrupts : <a b> where a is the interrupt number and b is a
+ field that represents an encoding of the sense and level
+ information for the interrupt. This should be encoded based on
+ the information in section 2) depending on the type of interrupt
+ controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device.
+ - fsl,preserve-clocking : boolean; if defined, the clock settings
+ from the bootloader are preserved (not touched).
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+ - fsl,timeout : I2C bus timeout in microseconds.
+
+Examples :
+
+ /* MPC5121 based board */
+ i2c@1740 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5121-i2c", "fsl-i2c";
+ reg = <0x1740 0x20>;
+ interrupts = <11 0x8>;
+ interrupt-parent = <&ipic>;
+ clock-frequency = <100000>;
+ };
+
+ i2ccontrol@1760 {
+ compatible = "fsl,mpc5121-i2c-ctrl";
+ reg = <0x1760 0x8>;
+ };
+
+ /* MPC5200B based board */
+ i2c@3d00 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+ reg = <0x3d00 0x40>;
+ interrupts = <2 15 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ fsl,preserve-clocking;
+ };
+
+ /* MPC8544 base board */
+ i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc8544-i2c", "fsl-i2c";
+ reg = <0x3100 0x100>;
+ interrupts = <43 2>;
+ interrupt-parent = <&mpic>;
+ clock-frequency = <400000>;
+ fsl,timeout = <10000>;
+ };
--- /dev/null
+Common i2c bus multiplexer/switch properties.
+
+An i2c bus multiplexer/switch will have several child busses that are
+numbered uniquely in a device dependent manner. The nodes for an i2c bus
+multiplexer/switch will have one child node for each child
+bus.
+
+Required properties:
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Required properties for child nodes:
+- #address-cells = <1>;
+- #size-cells = <0>;
+- reg : The sub-bus number.
+
+Optional properties for child nodes:
+- Other properties specific to the multiplexer/switch hardware.
+- Child nodes conforming to i2c bus binding
+
+
+Example :
+
+ /*
+ An NXP pca9548 8 channel I2C multiplexer at address 0x70
+ with two NXP pca8574 GPIO expanders attached, one each to
+ ports 3 and 4.
+ */
+
+ mux@70 {
+ compatible = "nxp,pca9548";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ gpio1: gpio@38 {
+ compatible = "nxp,pca8574";
+ reg = <0x38>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+ };
+ i2c@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+
+ gpio2: gpio@38 {
+ compatible = "nxp,pca8574";
+ reg = <0x38>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+ };
+ };
--- /dev/null
+
+* Marvell MV64XXX I2C controller
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : Should be "marvell,mv64xxx-i2c"
+ - interrupts : The interrupt number
+ - clock-frequency : Desired I2C bus clock frequency in Hz.
+
+Examples:
+
+ i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x20>;
+ interrupts = <29>;
+ clock-frequency = <100000>;
+ };
--- /dev/null
+I2C for Nomadik based systems
+
+Required (non-standard) properties:
+ - Nil
+
+Recommended (non-standard) properties:
+ - clock-frequency : Maximum bus clock frequency for the device
+
+Optional (non-standard) properties:
+ - Nil
+
+Example :
+
+i2c@80004000 {
+ compatible = "stericsson,db8500-i2c", "st,nomadik-i2c";
+ reg = <0x80004000 0x1000>;
+ interrupts = <0 21 0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ v-i2c-supply = <&db8500_vape_reg>;
+
+ clock-frequency = <400000>;
+};
--- /dev/null
+* Two Wire Serial Interface (TWSI) / I2C
+
+- compatible: "cavium,octeon-3860-twsi"
+
+ Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the TWSI/I2C bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>. I2C addresses have no size component.
+
+- interrupts: A single interrupt specifier.
+
+- clock-frequency: The I2C bus clock rate in Hz.
+
+Example:
+ twsi0: i2c@1180000001000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "cavium,octeon-3860-twsi";
+ reg = <0x11800 0x00001000 0x0 0x200>;
+ interrupts = <0 45>;
+ clock-frequency = <100000>;
+
+ rtc@68 {
+ compatible = "dallas,ds1337";
+ reg = <0x68>;
+ };
+ tmp@4c {
+ compatible = "ti,tmp421";
+ reg = <0x4c>;
+ };
+ };
--- /dev/null
+I2C for OMAP platforms
+
+Required properties :
+- compatible : Must be "ti,omap3-i2c" or "ti,omap4-i2c"
+- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based)
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Recommended properties :
+- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise
+ the default 100 kHz frequency will be used.
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Note: Current implementation will fetch base address, irq and dma
+from omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Examples :
+
+i2c1: i2c@0 {
+ compatible = "ti,omap3-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "i2c1";
+ clock-frequency = <400000>;
+};
--- /dev/null
+* NXP PNX I2C Controller
+
+Required properties:
+
+ - reg: Offset and length of the register set for the device
+ - compatible: should be "nxp,pnx-i2c"
+ - interrupts: configure one interrupt line
+ - #address-cells: always 1 (for i2c addresses)
+ - #size-cells: always 0
+ - interrupt-parent: the phandle for the interrupt controller that
+ services interrupts for this device.
+
+Optional properties:
+
+ - clock-frequency: desired I2C bus clock frequency in Hz, Default: 100000 Hz
+
+Examples:
+
+ i2c1: i2c@400a0000 {
+ compatible = "nxp,pnx-i2c";
+ reg = <0x400a0000 0x100>;
+ interrupt-parent = <&mic>;
+ interrupts = <51 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@400a8000 {
+ compatible = "nxp,pnx-i2c";
+ reg = <0x400a8000 0x100>;
+ interrupt-parent = <&mic>;
+ interrupts = <50 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clock-frequency = <100000>;
+ };
--- /dev/null
+CE4100 I2C
+----------
+
+CE4100 has one PCI device which is described as the I2C-Controller. This
+PCI device has three PCI-bars, each bar contains a complete I2C
+controller. So we have a total of three independent I2C-Controllers
+which share only an interrupt line.
+The driver is probed via the PCI-ID and is gathering the information of
+attached devices from the devices tree.
+Grant Likely recommended to use the ranges property to map the PCI-Bar
+number to its physical address and to use this to find the child nodes
+of the specific I2C controller. This were his exact words:
+
+ Here's where the magic happens. Each entry in
+ ranges describes how the parent pci address space
+ (middle group of 3) is translated to the local
+ address space (first group of 2) and the size of
+ each range (last cell). In this particular case,
+ the first cell of the local address is chosen to be
+ 1:1 mapped to the BARs, and the second is the
+ offset from be base of the BAR (which would be
+ non-zero if you had 2 or more devices mapped off
+ the same BAR)
+
+ ranges allows the address mapping to be described
+ in a way that the OS can interpret without
+ requiring custom device driver code.
+
+This is an example which is used on FalconFalls:
+------------------------------------------------
+ i2c-controller@b,2 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "pci8086,2e68.2",
+ "pci8086,2e68",
+ "pciclass,ff0000",
+ "pciclass,ff00";
+
+ reg = <0x15a00 0x0 0x0 0x0 0x0>;
+ interrupts = <16 1>;
+
+ /* as described by Grant, the first number in the group of
+ * three is the bar number followed by the 64bit bar address
+ * followed by size of the mapping. The bar address
+ * requires also a valid translation in parents ranges
+ * property.
+ */
+ ranges = <0 0 0x02000000 0 0xdffe0500 0x100
+ 1 0 0x02000000 0 0xdffe0600 0x100
+ 2 0 0x02000000 0 0xdffe0700 0x100>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "intel,ce4100-i2c-controller";
+
+ /* The first number in the reg property is the
+ * number of the bar
+ */
+ reg = <0 0 0x100>;
+
+ /* This I2C controller has no devices */
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "intel,ce4100-i2c-controller";
+ reg = <1 0 0x100>;
+
+ /* This I2C controller has one gpio controller */
+ gpio@26 {
+ #gpio-cells = <2>;
+ compatible = "ti,pcf8575";
+ reg = <0x26>;
+ gpio-controller;
+ };
+ };
+
+ i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "intel,ce4100-i2c-controller";
+ reg = <2 0 0x100>;
+
+ gpio@26 {
+ #gpio-cells = <2>;
+ compatible = "ti,pcf8575";
+ reg = <0x26>;
+ gpio-controller;
+ };
+ };
+ };
--- /dev/null
+* Marvell MMP I2C controller
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "mrvl,mmp-twsi" where mmp is the name of a
+ compatible processor, e.g. pxa168, pxa910, mmp2, mmp3.
+ For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required
+ as shown in the example below.
+
+Recommended properties :
+
+ - interrupts : the interrupt number
+ - interrupt-parent : the phandle for the interrupt controller that
+ services interrupts for this device. If the parent is the default
+ interrupt controller in device tree, it could be ignored.
+ - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling
+ status register of i2c controller instead.
+ - mrvl,i2c-fast-mode : Enable fast mode of i2c controller.
+
+Examples:
+ twsi1: i2c@d4011000 {
+ compatible = "mrvl,mmp-twsi";
+ reg = <0xd4011000 0x1000>;
+ interrupts = <7>;
+ mrvl,i2c-fast-mode;
+ };
+
+ twsi2: i2c@d4025000 {
+ compatible = "mrvl,mmp-twsi";
+ reg = <0xd4025000 0x1000>;
+ interrupts = <58>;
+ };
--- /dev/null
+* Samsung's I2C controller
+
+The Samsung's I2C controller is used to interface with I2C devices.
+
+Required properties:
+ - compatible: value should be either of the following.
+ (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
+ (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
+ (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
+ inside HDMIPHY block found on several samsung SoCs
+ - reg: physical base address of the controller and length of memory mapped
+ region.
+ - interrupts: interrupt number to the cpu.
+ - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
+
+Optional properties:
+ - gpios: The order of the gpios should be the following: <SDA, SCL>.
+ The gpio specifier depends on the gpio controller. Required in all
+ cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
+ lines are permanently wired to the respective client
+ - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
+ specified, default value is 0.
+ - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
+ specified, the default value in Hz is 100000.
+
+Example:
+
+ i2c@13870000 {
+ compatible = "samsung,s3c2440-i2c";
+ reg = <0x13870000 0x100>;
+ interrupts = <345>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <100000>;
+ gpios = <&gpd1 2 0 /* SDA */
+ &gpd1 3 0 /* SCL */>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wm8994@1a {
+ compatible = "wlf,wm8994";
+ reg = <0x1a>;
+ };
+ };
--- /dev/null
+I2C for SiRFprimaII platforms
+
+Required properties :
+- compatible : Must be "sirf,prima2-i2c"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: interrupt number to the cpu.
+
+Optional properties:
+- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
+ The absence of the propoerty indicates the default frequency 100 kHz.
+
+Examples :
+
+i2c0: i2c@b00e0000 {
+ compatible = "sirf,prima2-i2c";
+ reg = <0xb00e0000 0x10000>;
+ interrupts = <24>;
+};
--- /dev/null
+i2c Controller on ARM Versatile platform:
+
+Required properties:
+- compatible : Must be "arm,versatile-i2c";
+- reg
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
--- /dev/null
+Xilinx IIC controller:
+
+Required properties:
+- compatible : Must be "xlnx,xps-iic-2.00.a"
+- reg : IIC register location and length
+- interrupts : IIC controller unterrupt
+- #address-cells = <1>
+- #size-cells = <0>
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Example:
+
+ axi_iic_0: i2c@40800000 {
+ compatible = "xlnx,xps-iic-2.00.a";
+ interrupts = < 1 2 >;
+ reg = < 0x40800000 0x10000 >;
+
+ #size-cells = <0>;
+ #address-cells = <1>;
+ };
+++ /dev/null
-* Marvell MMP I2C controller
-
-Required properties :
-
- - reg : Offset and length of the register set for the device
- - compatible : should be "mrvl,mmp-twsi" where mmp is the name of a
- compatible processor, e.g. pxa168, pxa910, mmp2, mmp3.
- For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required
- as shown in the example below.
-
-Recommended properties :
-
- - interrupts : the interrupt number
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device. If the parent is the default
- interrupt controller in device tree, it could be ignored.
- - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling
- status register of i2c controller instead.
- - mrvl,i2c-fast-mode : Enable fast mode of i2c controller.
-
-Examples:
- twsi1: i2c@d4011000 {
- compatible = "mrvl,mmp-twsi";
- reg = <0xd4011000 0x1000>;
- interrupts = <7>;
- mrvl,i2c-fast-mode;
- };
-
- twsi2: i2c@d4025000 {
- compatible = "mrvl,mmp-twsi";
- reg = <0xd4025000 0x1000>;
- interrupts = <58>;
- };
-
-* Marvell MV64XXX I2C controller
-
-Required properties :
-
- - reg : Offset and length of the register set for the device
- - compatible : Should be "marvell,mv64xxx-i2c"
- - interrupts : The interrupt number
- - clock-frequency : Desired I2C bus clock frequency in Hz.
-
-Examples:
-
- i2c@11000 {
- compatible = "marvell,mv64xxx-i2c";
- reg = <0x11000 0x20>;
- interrupts = <29>;
- clock-frequency = <100000>;
- };
+++ /dev/null
-Common i2c bus multiplexer/switch properties.
-
-An i2c bus multiplexer/switch will have several child busses that are
-numbered uniquely in a device dependent manner. The nodes for an i2c bus
-multiplexer/switch will have one child node for each child
-bus.
-
-Required properties:
-- #address-cells = <1>;
-- #size-cells = <0>;
-
-Required properties for child nodes:
-- #address-cells = <1>;
-- #size-cells = <0>;
-- reg : The sub-bus number.
-
-Optional properties for child nodes:
-- Other properties specific to the multiplexer/switch hardware.
-- Child nodes conforming to i2c bus binding
-
-
-Example :
-
- /*
- An NXP pca9548 8 channel I2C multiplexer at address 0x70
- with two NXP pca8574 GPIO expanders attached, one each to
- ports 3 and 4.
- */
-
- mux@70 {
- compatible = "nxp,pca9548";
- reg = <0x70>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- i2c@3 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <3>;
-
- gpio1: gpio@38 {
- compatible = "nxp,pca8574";
- reg = <0x38>;
- #gpio-cells = <2>;
- gpio-controller;
- };
- };
- i2c@4 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <4>;
-
- gpio2: gpio@38 {
- compatible = "nxp,pca8574";
- reg = <0x38>;
- #gpio-cells = <2>;
- gpio-controller;
- };
- };
- };
+++ /dev/null
-I2C for Nomadik based systems
-
-Required (non-standard) properties:
- - Nil
-
-Recommended (non-standard) properties:
- - clock-frequency : Maximum bus clock frequency for the device
-
-Optional (non-standard) properties:
- - Nil
-
-Example :
-
-i2c@80004000 {
- compatible = "stericsson,db8500-i2c", "st,nomadik-i2c";
- reg = <0x80004000 0x1000>;
- interrupts = <0 21 0x4>;
- #address-cells = <1>;
- #size-cells = <0>;
- v-i2c-supply = <&db8500_vape_reg>;
-
- clock-frequency = <400000>;
-};
+++ /dev/null
-I2C for OMAP platforms
-
-Required properties :
-- compatible : Must be "ti,omap3-i2c" or "ti,omap4-i2c"
-- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based)
-- #address-cells = <1>;
-- #size-cells = <0>;
-
-Recommended properties :
-- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise
- the default 100 kHz frequency will be used.
-
-Optional properties:
-- Child nodes conforming to i2c bus binding
-
-Note: Current implementation will fetch base address, irq and dma
-from omap hwmod data base during device registration.
-Future plan is to migrate hwmod data base contents into device tree
-blob so that, all the required data will be used from device tree dts
-file.
-
-Examples :
-
-i2c1: i2c@0 {
- compatible = "ti,omap3-i2c";
- #address-cells = <1>;
- #size-cells = <0>;
- ti,hwmods = "i2c1";
- clock-frequency = <400000>;
-};
+++ /dev/null
-* NXP PNX I2C Controller
-
-Required properties:
-
- - reg: Offset and length of the register set for the device
- - compatible: should be "nxp,pnx-i2c"
- - interrupts: configure one interrupt line
- - #address-cells: always 1 (for i2c addresses)
- - #size-cells: always 0
- - interrupt-parent: the phandle for the interrupt controller that
- services interrupts for this device.
-
-Optional properties:
-
- - clock-frequency: desired I2C bus clock frequency in Hz, Default: 100000 Hz
-
-Examples:
-
- i2c1: i2c@400a0000 {
- compatible = "nxp,pnx-i2c";
- reg = <0x400a0000 0x100>;
- interrupt-parent = <&mic>;
- interrupts = <51 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c@400a8000 {
- compatible = "nxp,pnx-i2c";
- reg = <0x400a8000 0x100>;
- interrupt-parent = <&mic>;
- interrupts = <50 0>;
- #address-cells = <1>;
- #size-cells = <0>;
- clock-frequency = <100000>;
- };
+++ /dev/null
-* Samsung's I2C controller
-
-The Samsung's I2C controller is used to interface with I2C devices.
-
-Required properties:
- - compatible: value should be either of the following.
- (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
- (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
- (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
- inside HDMIPHY block found on several samsung SoCs
- - reg: physical base address of the controller and length of memory mapped
- region.
- - interrupts: interrupt number to the cpu.
- - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
-
-Optional properties:
- - gpios: The order of the gpios should be the following: <SDA, SCL>.
- The gpio specifier depends on the gpio controller. Required in all
- cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
- lines are permanently wired to the respective client
- - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
- specified, default value is 0.
- - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
- specified, the default value in Hz is 100000.
-
-Example:
-
- i2c@13870000 {
- compatible = "samsung,s3c2440-i2c";
- reg = <0x13870000 0x100>;
- interrupts = <345>;
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <100000>;
- gpios = <&gpd1 2 0 /* SDA */
- &gpd1 3 0 /* SCL */>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- wm8994@1a {
- compatible = "wlf,wm8994";
- reg = <0x1a>;
- };
- };
+++ /dev/null
-I2C for SiRFprimaII platforms
-
-Required properties :
-- compatible : Must be "sirf,prima2-i2c"
-- reg: physical base address of the controller and length of memory mapped
- region.
-- interrupts: interrupt number to the cpu.
-
-Optional properties:
-- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
- The absence of the propoerty indicates the default frequency 100 kHz.
-
-Examples :
-
-i2c0: i2c@b00e0000 {
- compatible = "sirf,prima2-i2c";
- reg = <0xb00e0000 0x10000>;
- interrupts = <24>;
-};
+++ /dev/null
-Xilinx IIC controller:
-
-Required properties:
-- compatible : Must be "xlnx,xps-iic-2.00.a"
-- reg : IIC register location and length
-- interrupts : IIC controller unterrupt
-- #address-cells = <1>
-- #size-cells = <0>
-
-Optional properties:
-- Child nodes conforming to i2c bus binding
-
-Example:
-
- axi_iic_0: i2c@40800000 {
- compatible = "xlnx,xps-iic-2.00.a";
- interrupts = < 1 2 >;
- reg = < 0x40800000 0x10000 >;
-
- #size-cells = <0>;
- #address-cells = <1>;
- };
* kind, whether express or implied.
*/
-/*
- * This driver can be used from the device tree, see
- * Documentation/devicetree/bindings/i2c/ocore-i2c.txt
- */
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
projects / cascardo / linux.git / commitdiff