#define RSN_AKM_NONE 0 /* None (IBSS) */
#define RSN_AKM_UNSPECIFIED 1 /* Over 802.1x */
#define RSN_AKM_PSK 2 /* Pre-shared Key */
+#define RSN_AKM_SHA256_1X 5 /* SHA256, 802.1X */
+#define RSN_AKM_SHA256_PSK 6 /* SHA256, Pre-shared Key */
#define RSN_CAP_LEN 2 /* Length of RSN capabilities */
-#define RSN_CAP_PTK_REPLAY_CNTR_MASK 0x000C
+#define RSN_CAP_PTK_REPLAY_CNTR_MASK (BIT(2) | BIT(3))
+#define RSN_CAP_MFPR_MASK BIT(6)
+#define RSN_CAP_MFPC_MASK BIT(7)
+#define RSN_PMKID_COUNT_LEN 2
#define VNDR_IE_CMD_LEN 4 /* length of the set command
* string :"add", "del" (+ NUL)
REG_RULE(5470-10, 5850+10, 80, 6, 20, 0), }
};
-static const u32 __wl_cipher_suites[] = {
+/* Note: brcmf_cipher_suites is an array of int defining which cipher suites
+ * are supported. A pointer to this array and the number of entries is passed
+ * on to upper layers. AES_CMAC defines whether or not the driver supports MFP.
+ * So the cipher suite AES_CMAC has to be the last one in the array, and when
+ * device does not support MFP then the number of suites will be decreased by 1
+ */
+static const u32 brcmf_cipher_suites[] = {
WLAN_CIPHER_SUITE_WEP40,
WLAN_CIPHER_SUITE_WEP104,
WLAN_CIPHER_SUITE_TKIP,
WLAN_CIPHER_SUITE_CCMP,
- WLAN_CIPHER_SUITE_AES_CMAC,
+ /* Keep as last entry: */
+ WLAN_CIPHER_SUITE_AES_CMAC
};
/* Vendor specific ie. id = 221, oui and type defines exact ie */
static s32
brcmf_set_wsec_mode(struct net_device *ndev,
- struct cfg80211_connect_params *sme, bool mfp)
+ struct cfg80211_connect_params *sme)
{
struct brcmf_cfg80211_profile *profile = ndev_to_prof(ndev);
struct brcmf_cfg80211_security *sec;
sme->privacy)
pval = AES_ENABLED;
- if (mfp)
- wsec = pval | gval | MFP_CAPABLE;
- else
- wsec = pval | gval;
+ wsec = pval | gval;
err = brcmf_fil_bsscfg_int_set(netdev_priv(ndev), "wsec", wsec);
if (err) {
brcmf_err("error (%d)\n", err);
static s32
brcmf_set_key_mgmt(struct net_device *ndev, struct cfg80211_connect_params *sme)
{
- struct brcmf_cfg80211_profile *profile = ndev_to_prof(ndev);
- struct brcmf_cfg80211_security *sec;
- s32 val = 0;
- s32 err = 0;
+ struct brcmf_if *ifp = netdev_priv(ndev);
+ s32 val;
+ s32 err;
+ const struct brcmf_tlv *rsn_ie;
+ const u8 *ie;
+ u32 ie_len;
+ u32 offset;
+ u16 rsn_cap;
+ u32 mfp;
+ u16 count;
- if (sme->crypto.n_akm_suites) {
- err = brcmf_fil_bsscfg_int_get(netdev_priv(ndev),
- "wpa_auth", &val);
- if (err) {
- brcmf_err("could not get wpa_auth (%d)\n", err);
- return err;
+ if (!sme->crypto.n_akm_suites)
+ return 0;
+
+ err = brcmf_fil_bsscfg_int_get(netdev_priv(ndev), "wpa_auth", &val);
+ if (err) {
+ brcmf_err("could not get wpa_auth (%d)\n", err);
+ return err;
+ }
+ if (val & (WPA_AUTH_PSK | WPA_AUTH_UNSPECIFIED)) {
+ switch (sme->crypto.akm_suites[0]) {
+ case WLAN_AKM_SUITE_8021X:
+ val = WPA_AUTH_UNSPECIFIED;
+ break;
+ case WLAN_AKM_SUITE_PSK:
+ val = WPA_AUTH_PSK;
+ break;
+ default:
+ brcmf_err("invalid cipher group (%d)\n",
+ sme->crypto.cipher_group);
+ return -EINVAL;
}
- if (val & (WPA_AUTH_PSK | WPA_AUTH_UNSPECIFIED)) {
- switch (sme->crypto.akm_suites[0]) {
- case WLAN_AKM_SUITE_8021X:
- val = WPA_AUTH_UNSPECIFIED;
- break;
- case WLAN_AKM_SUITE_PSK:
- val = WPA_AUTH_PSK;
- break;
- default:
- brcmf_err("invalid cipher group (%d)\n",
- sme->crypto.cipher_group);
- return -EINVAL;
- }
- } else if (val & (WPA2_AUTH_PSK | WPA2_AUTH_UNSPECIFIED)) {
- switch (sme->crypto.akm_suites[0]) {
- case WLAN_AKM_SUITE_8021X:
- val = WPA2_AUTH_UNSPECIFIED;
- break;
- case WLAN_AKM_SUITE_PSK:
- val = WPA2_AUTH_PSK;
- break;
- default:
- brcmf_err("invalid cipher group (%d)\n",
- sme->crypto.cipher_group);
- return -EINVAL;
- }
+ } else if (val & (WPA2_AUTH_PSK | WPA2_AUTH_UNSPECIFIED)) {
+ switch (sme->crypto.akm_suites[0]) {
+ case WLAN_AKM_SUITE_8021X:
+ val = WPA2_AUTH_UNSPECIFIED;
+ break;
+ case WLAN_AKM_SUITE_8021X_SHA256:
+ val = WPA2_AUTH_1X_SHA256;
+ break;
+ case WLAN_AKM_SUITE_PSK_SHA256:
+ val = WPA2_AUTH_PSK_SHA256;
+ break;
+ case WLAN_AKM_SUITE_PSK:
+ val = WPA2_AUTH_PSK;
+ break;
+ default:
+ brcmf_err("invalid cipher group (%d)\n",
+ sme->crypto.cipher_group);
+ return -EINVAL;
}
+ }
- brcmf_dbg(CONN, "setting wpa_auth to %d\n", val);
- err = brcmf_fil_bsscfg_int_set(netdev_priv(ndev),
- "wpa_auth", val);
- if (err) {
- brcmf_err("could not set wpa_auth (%d)\n", err);
- return err;
- }
+ if (!brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MFP))
+ goto skip_mfp_config;
+ /* The MFP mode (1 or 2) needs to be determined, parse IEs. The
+ * IE will not be verified, just a quick search for MFP config
+ */
+ rsn_ie = brcmf_parse_tlvs((const u8 *)sme->ie, sme->ie_len,
+ WLAN_EID_RSN);
+ if (!rsn_ie)
+ goto skip_mfp_config;
+ ie = (const u8 *)rsn_ie;
+ ie_len = rsn_ie->len + TLV_HDR_LEN;
+ /* Skip unicast suite */
+ offset = TLV_HDR_LEN + WPA_IE_VERSION_LEN + WPA_IE_MIN_OUI_LEN;
+ if (offset + WPA_IE_SUITE_COUNT_LEN >= ie_len)
+ goto skip_mfp_config;
+ /* Skip multicast suite */
+ count = ie[offset] + (ie[offset + 1] << 8);
+ offset += WPA_IE_SUITE_COUNT_LEN + (count * WPA_IE_MIN_OUI_LEN);
+ if (offset + WPA_IE_SUITE_COUNT_LEN >= ie_len)
+ goto skip_mfp_config;
+ /* Skip auth key management suite(s) */
+ count = ie[offset] + (ie[offset + 1] << 8);
+ offset += WPA_IE_SUITE_COUNT_LEN + (count * WPA_IE_MIN_OUI_LEN);
+ if (offset + WPA_IE_SUITE_COUNT_LEN > ie_len)
+ goto skip_mfp_config;
+ /* Ready to read capabilities */
+ mfp = BRCMF_MFP_NONE;
+ rsn_cap = ie[offset] + (ie[offset + 1] << 8);
+ if (rsn_cap & RSN_CAP_MFPR_MASK)
+ mfp = BRCMF_MFP_REQUIRED;
+ else if (rsn_cap & RSN_CAP_MFPC_MASK)
+ mfp = BRCMF_MFP_CAPABLE;
+ brcmf_fil_bsscfg_int_set(netdev_priv(ndev), "mfp", mfp);
+
+skip_mfp_config:
+ brcmf_dbg(CONN, "setting wpa_auth to %d\n", val);
+ err = brcmf_fil_bsscfg_int_set(netdev_priv(ndev), "wpa_auth", val);
+ if (err) {
+ brcmf_err("could not set wpa_auth (%d)\n", err);
+ return err;
}
- sec = &profile->sec;
- sec->wpa_auth = sme->crypto.akm_suites[0];
return err;
}
goto done;
}
- err = brcmf_set_wsec_mode(ndev, sme, sme->mfp == NL80211_MFP_REQUIRED);
+ err = brcmf_set_wsec_mode(ndev, sme);
if (err) {
brcmf_err("wl_set_set_cipher failed (%d)\n", err);
goto done;
u8 key_idx, bool pairwise, const u8 *mac_addr)
{
struct brcmf_if *ifp = netdev_priv(ndev);
- struct brcmf_wsec_key key;
- s32 err = 0;
+ struct brcmf_wsec_key *key;
+ s32 err;
brcmf_dbg(TRACE, "Enter\n");
+ brcmf_dbg(CONN, "key index (%d)\n", key_idx);
+
if (!check_vif_up(ifp->vif))
return -EIO;
return -EINVAL;
}
- memset(&key, 0, sizeof(key));
+ key = &ifp->vif->profile.key[key_idx];
- key.index = (u32)key_idx;
- key.flags = BRCMF_PRIMARY_KEY;
- key.algo = CRYPTO_ALGO_OFF;
+ if (key->algo == CRYPTO_ALGO_OFF) {
+ brcmf_dbg(CONN, "Ignore clearing of (never configured) key\n");
+ return -EINVAL;
+ }
- brcmf_dbg(CONN, "key index (%d)\n", key_idx);
+ memset(key, 0, sizeof(*key));
+ key->index = (u32)key_idx;
+ key->flags = BRCMF_PRIMARY_KEY;
- /* Set the new key/index */
- err = send_key_to_dongle(ifp, &key);
+ /* Clear the key/index */
+ err = send_key_to_dongle(ifp, key);
brcmf_dbg(TRACE, "Exit\n");
return err;
static s32
brcmf_cfg80211_add_key(struct wiphy *wiphy, struct net_device *ndev,
- u8 key_idx, bool pairwise, const u8 *mac_addr,
- struct key_params *params)
+ u8 key_idx, bool pairwise, const u8 *mac_addr,
+ struct key_params *params)
{
struct brcmf_if *ifp = netdev_priv(ndev);
struct brcmf_wsec_key *key;
}
static s32
-brcmf_cfg80211_get_key(struct wiphy *wiphy, struct net_device *ndev,
- u8 key_idx, bool pairwise, const u8 *mac_addr, void *cookie,
- void (*callback) (void *cookie, struct key_params * params))
+brcmf_cfg80211_get_key(struct wiphy *wiphy, struct net_device *ndev, u8 key_idx,
+ bool pairwise, const u8 *mac_addr, void *cookie,
+ void (*callback)(void *cookie,
+ struct key_params *params))
{
struct key_params params;
struct brcmf_if *ifp = netdev_priv(ndev);
static s32
brcmf_cfg80211_config_default_mgmt_key(struct wiphy *wiphy,
- struct net_device *ndev, u8 key_idx)
+ struct net_device *ndev, u8 key_idx)
{
+ struct brcmf_if *ifp = netdev_priv(ndev);
+
+ brcmf_dbg(TRACE, "Enter key_idx %d\n", key_idx);
+
+ if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MFP))
+ return 0;
+
brcmf_dbg(INFO, "Not supported\n");
return -EOPNOTSUPP;
u32 auth = 0; /* d11 open authentication */
u16 count;
s32 err = 0;
- s32 len = 0;
+ s32 len;
u32 i;
u32 wsec;
u32 pval = 0;
u8 *data;
u16 rsn_cap;
u32 wme_bss_disable;
+ u32 mfp;
brcmf_dbg(TRACE, "Enter\n");
if (wpa_ie == NULL)
is_rsn_ie ? (wpa_auth |= WPA2_AUTH_PSK) :
(wpa_auth |= WPA_AUTH_PSK);
break;
+ case RSN_AKM_SHA256_PSK:
+ brcmf_dbg(TRACE, "RSN_AKM_MFP_PSK\n");
+ wpa_auth |= WPA2_AUTH_PSK_SHA256;
+ break;
+ case RSN_AKM_SHA256_1X:
+ brcmf_dbg(TRACE, "RSN_AKM_MFP_1X\n");
+ wpa_auth |= WPA2_AUTH_1X_SHA256;
+ break;
default:
brcmf_err("Ivalid key mgmt info\n");
}
offset++;
}
+ mfp = BRCMF_MFP_NONE;
if (is_rsn_ie) {
wme_bss_disable = 1;
if ((offset + RSN_CAP_LEN) <= len) {
rsn_cap = data[offset] + (data[offset + 1] << 8);
if (rsn_cap & RSN_CAP_PTK_REPLAY_CNTR_MASK)
wme_bss_disable = 0;
+ if (rsn_cap & RSN_CAP_MFPR_MASK) {
+ brcmf_dbg(TRACE, "MFP Required\n");
+ mfp = BRCMF_MFP_REQUIRED;
+ /* Firmware only supports mfp required in
+ * combination with WPA2_AUTH_PSK_SHA256 or
+ * WPA2_AUTH_1X_SHA256.
+ */
+ if (!(wpa_auth & (WPA2_AUTH_PSK_SHA256 |
+ WPA2_AUTH_1X_SHA256))) {
+ err = -EINVAL;
+ goto exit;
+ }
+ /* Firmware has requirement that WPA2_AUTH_PSK/
+ * WPA2_AUTH_UNSPECIFIED be set, if SHA256 OUI
+ * is to be included in the rsn ie.
+ */
+ if (wpa_auth & WPA2_AUTH_PSK_SHA256)
+ wpa_auth |= WPA2_AUTH_PSK;
+ else if (wpa_auth & WPA2_AUTH_1X_SHA256)
+ wpa_auth |= WPA2_AUTH_UNSPECIFIED;
+ } else if (rsn_cap & RSN_CAP_MFPC_MASK) {
+ brcmf_dbg(TRACE, "MFP Capable\n");
+ mfp = BRCMF_MFP_CAPABLE;
+ }
}
+ offset += RSN_CAP_LEN;
/* set wme_bss_disable to sync RSN Capabilities */
err = brcmf_fil_bsscfg_int_set(ifp, "wme_bss_disable",
wme_bss_disable);
brcmf_err("wme_bss_disable error %d\n", err);
goto exit;
}
+
+ /* Skip PMKID cnt as it is know to be 0 for AP. */
+ offset += RSN_PMKID_COUNT_LEN;
+
+ /* See if there is BIP wpa suite left for MFP */
+ if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MFP) &&
+ ((offset + WPA_IE_MIN_OUI_LEN) <= len)) {
+ err = brcmf_fil_bsscfg_data_set(ifp, "bip",
+ &data[offset],
+ WPA_IE_MIN_OUI_LEN);
+ if (err < 0) {
+ brcmf_err("bip error %d\n", err);
+ goto exit;
+ }
+ }
}
/* FOR WPS , set SES_OW_ENABLED */
wsec = (pval | gval | SES_OW_ENABLED);
brcmf_err("wsec error %d\n", err);
goto exit;
}
+ /* Configure MFP, this needs to go after wsec otherwise the wsec command
+ * will overwrite the values set by MFP
+ */
+ if (brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MFP)) {
+ err = brcmf_fil_bsscfg_int_set(ifp, "mfp", mfp);
+ if (err < 0) {
+ brcmf_err("mfp error %d\n", err);
+ goto exit;
+ }
+ }
/* set upper-layer auth */
err = brcmf_fil_bsscfg_int_set(ifp, "wpa_auth", wpa_auth);
if (err < 0) {
wiphy->n_addresses = i;
wiphy->signal_type = CFG80211_SIGNAL_TYPE_MBM;
- wiphy->cipher_suites = __wl_cipher_suites;
- wiphy->n_cipher_suites = ARRAY_SIZE(__wl_cipher_suites);
+ wiphy->cipher_suites = brcmf_cipher_suites;
+ wiphy->n_cipher_suites = ARRAY_SIZE(brcmf_cipher_suites);
+ if (!brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MFP))
+ wiphy->n_cipher_suites--;
wiphy->flags |= WIPHY_FLAG_PS_ON_BY_DEFAULT |
WIPHY_FLAG_OFFCHAN_TX |
WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL;
projects / cascardo / linux.git / commitdiff