ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
support on the platform.
ti,x-plate-resistance: X plate resistance
- ti,coordiante-readouts: The sequencer supports a total of 16
+ ti,coordinate-readouts: The sequencer supports a total of 16
programmable steps each step is used to
read a single coordinate. A single
readout is enough but multiple reads can
BTN_DPAD_*
Analog buttons are reported as:
ABS_HAT0X and ABS_HAT0Y
+ (for ABS values negative is left/up, positive is right/down)
Analog-Sticks:
The left analog-stick is reported as ABS_X, ABS_Y. The right analog stick is
reported as ABS_RX, ABS_RY. Zero, one or two sticks may be present.
If analog-sticks provide digital buttons, they are mapped accordingly as
BTN_THUMBL (first/left) and BTN_THUMBR (second/right).
+ (for ABS values negative is left/up, positive is right/down)
Triggers:
Trigger buttons can be available as digital or analog buttons or both. User-
ABS_HAT2X (right/ZR) and BTN_TL2 or ABS_HAT2Y (left/ZL).
If only one trigger-button combination is present (upper+lower), they are
reported as "right" triggers (BTN_TR/ABS_HAT1X).
+ (ABS trigger values start at 0, pressure is reported as positive values)
Menu-Pad:
Menu buttons are always digital and are mapped according to their location
tsc {
ti,wires = <4>;
ti,x-plate-resistance = <200>;
- ti,coordiante-readouts = <5>;
+ ti,coordinate-readouts = <5>;
ti,wire-config = <0x00 0x11 0x22 0x33>;
};
tx-num-evt = <1>;
rx-num-evt = <1>;
};
+
+&tscadc {
+ status = "okay";
+ tsc {
+ ti,wires = <4>;
+ ti,x-plate-resistance = <200>;
+ ti,coordinate-readouts = <5>;
+ ti,wire-config = <0x00 0x11 0x22 0x33>;
+ };
+};
comment "Userland interfaces"
config INPUT_MOUSEDEV
- tristate "Mouse interface" if EXPERT
+ tristate "Mouse interface"
default y
help
Say Y here if you want your mouse to be accessible as char devices
#include <linux/poll.h>
#include <linux/sched.h>
#include <linux/slab.h>
+#include <linux/vmalloc.h>
+#include <linux/mm.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/input/mt.h>
mutex_unlock(&evdev->mutex);
evdev_detach_client(evdev, client);
- kfree(client);
+
+ if (is_vmalloc_addr(client))
+ vfree(client);
+ else
+ kfree(client);
evdev_close_device(evdev);
{
struct evdev *evdev = container_of(inode->i_cdev, struct evdev, cdev);
unsigned int bufsize = evdev_compute_buffer_size(evdev->handle.dev);
+ unsigned int size = sizeof(struct evdev_client) +
+ bufsize * sizeof(struct input_event);
struct evdev_client *client;
int error;
- client = kzalloc(sizeof(struct evdev_client) +
- bufsize * sizeof(struct input_event),
- GFP_KERNEL);
+ client = kzalloc(size, GFP_KERNEL | __GFP_NOWARN);
+ if (!client)
+ client = vzalloc(size);
if (!client)
return -ENOMEM;
if (dev->hint_events_per_packet < packet_size)
dev->hint_events_per_packet = packet_size;
- dev->max_vals = max(dev->hint_events_per_packet, packet_size) + 2;
+ dev->max_vals = dev->hint_events_per_packet + 2;
dev->vals = kcalloc(dev->max_vals, sizeof(*dev->vals), GFP_KERNEL);
if (!dev->vals) {
error = -ENOMEM;
# Input core configuration
#
menuconfig INPUT_KEYBOARD
- bool "Keyboards" if EXPERT || !X86
+ bool "Keyboards"
default y
help
Say Y here, and a list of supported keyboards will be displayed.
module will be called atakbd.
config KEYBOARD_ATKBD
- tristate "AT keyboard" if EXPERT || !X86
+ tristate "AT keyboard"
default y
select SERIO
select SERIO_LIBPS2
config KEYBOARD_SH_KEYSC
tristate "SuperH KEYSC keypad support"
- depends on SUPERH || ARCH_SHMOBILE
+ depends on SUPERH || ARM || COMPILE_TEST
help
Say Y here if you want to use a keypad attached to the KEYSC block
on SuperH processors such as sh7722 and sh7343.
#include <linux/gpio_keys.h>
#include <linux/workqueue.h>
#include <linux/gpio.h>
+#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/of_gpio.h>
#include <linux/spinlock.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
+#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/of_gpio.h>
.name = DRV_NAME,
.owner = THIS_MODULE,
.pm = &lpc32xx_kscan_pm_ops,
- .of_match_table = of_match_ptr(lpc32xx_kscan_match),
+ .of_match_table = lpc32xx_kscan_match,
}
};
return error;
error = nspire_keypad_chip_init(keypad);
- if (error)
+ if (error) {
+ clk_disable_unprepare(keypad->clk);
return error;
+ }
return 0;
}
.driver = {
.name = "nspire-keypad",
.owner = THIS_MODULE,
- .of_match_table = of_match_ptr(nspire_keypad_dt_match),
+ .of_match_table = nspire_keypad_dt_match,
},
.probe = nspire_keypad_probe,
};
#include <linux/err.h>
#include <linux/input/matrix_keypad.h>
#include <linux/slab.h>
+#include <linux/of.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
unsigned int keymap_rows;
const struct of_device_id *match;
- match = of_match_device(of_match_ptr(tegra_kbc_of_match), &pdev->dev);
+ match = of_match_device(tegra_kbc_of_match, &pdev->dev);
kbc = devm_kzalloc(&pdev->dev, sizeof(*kbc), GFP_KERNEL);
if (!kbc) {
struct clk *clk;
struct device *dev;
spinlock_t lock;
- u32 irq_press;
- u32 irq_release;
+ int irq_press;
+ int irq_release;
int rows, cols, row_shift;
int debounce_ms, active_low;
u32 prev_keys[3];
config INPUT_MAX8997_HAPTIC
tristate "MAXIM MAX8997 haptic controller support"
- depends on HAVE_PWM && MFD_MAX8997
+ depends on PWM && HAVE_PWM && MFD_MAX8997
select INPUT_FF_MEMLESS
help
This option enables device driver support for the haptic controller
config INPUT_PWM_BEEPER
tristate "PWM beeper support"
- depends on HAVE_PWM || PWM
+ depends on PWM && HAVE_PWM
help
Say Y here to get support for PWM based beeper devices.
struct ad714x_chip *chip = spi_get_drvdata(spi);
ad714x_remove(chip);
- spi_set_drvdata(spi, NULL);
return 0;
}
err_free_mem:
input_free_polled_device(poll_dev);
kfree(bdev);
- dev_set_drvdata(&pdev->dev, NULL);
return error;
}
input_free_polled_device(bdev->poll_dev);
iounmap(bdev->reg);
kfree(bdev);
- dev_set_drvdata(dev, NULL);
return 0;
}
* I2C init/probing/exit functions
*/
static int mma8450_probe(struct i2c_client *c,
- const struct i2c_device_id *id)
+ const struct i2c_device_id *id)
{
struct input_polled_dev *idev;
struct mma8450 *m;
goto err_free_mem;
}
+ i2c_set_clientdata(c, m);
+
return 0;
err_free_mem:
pm_runtime_enable(&client->dev);
pm_runtime_set_autosuspend_delay(&client->dev, MPU3050_AUTO_DELAY);
+ i2c_set_clientdata(client, sensor);
return 0;
#include <linux/input.h>
#include <linux/module.h>
#include <linux/kernel.h>
+#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/pwm.h>
#include <linux/slab.h>
input_unregister_polled_device(poll_dev);
input_free_polled_device(poll_dev);
- dev_set_drvdata(&pdev->dev, NULL);
return 0;
}
#include <linux/gpio.h>
#include <linux/rotary_encoder.h>
#include <linux/slab.h>
+#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/of_gpio.h>
.name = "sirfsoc-pwrc",
.owner = THIS_MODULE,
.pm = &sirfsoc_pwrc_pm_ops,
- .of_match_table = of_match_ptr(sirfsoc_pwrc_of_match),
+ .of_match_table = sirfsoc_pwrc_of_match,
}
};
return retval;
}
-static ssize_t uinput_inject_event(struct uinput_device *udev,
- const char __user *buffer, size_t count)
+static ssize_t uinput_inject_events(struct uinput_device *udev,
+ const char __user *buffer, size_t count)
{
struct input_event ev;
+ size_t bytes = 0;
- if (count < input_event_size())
+ if (count != 0 && count < input_event_size())
return -EINVAL;
- if (input_event_from_user(buffer, &ev))
- return -EFAULT;
+ while (bytes + input_event_size() <= count) {
+ /*
+ * Note that even if some events were fetched successfully
+ * we are still going to return EFAULT instead of partial
+ * count to let userspace know that it got it's buffers
+ * all wrong.
+ */
+ if (input_event_from_user(buffer + bytes, &ev))
+ return -EFAULT;
- input_event(udev->dev, ev.type, ev.code, ev.value);
+ input_event(udev->dev, ev.type, ev.code, ev.value);
+ bytes += input_event_size();
+ }
- return input_event_size();
+ return bytes;
}
static ssize_t uinput_write(struct file *file, const char __user *buffer,
return retval;
retval = udev->state == UIST_CREATED ?
- uinput_inject_event(udev, buffer, count) :
+ uinput_inject_events(udev, buffer, count) :
uinput_setup_device(udev, buffer, count);
mutex_unlock(&udev->mutex);
/* Dell Latitude E5500, E6400, E6500, Precision M4400 */
{ { 0x62, 0x02, 0x14 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf,
ALPS_PASS | ALPS_DUALPOINT | ALPS_PS2_INTERLEAVED },
- { { 0x73, 0x00, 0x14 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf, ALPS_DUALPOINT }, /* Dell XT2 */
{ { 0x73, 0x02, 0x50 }, 0x00, ALPS_PROTO_V2, 0xcf, 0xcf, ALPS_FOUR_BUTTONS }, /* Dell Vostro 1400 */
{ { 0x52, 0x01, 0x14 }, 0x00, ALPS_PROTO_V2, 0xff, 0xff,
ALPS_PASS | ALPS_DUALPOINT | ALPS_PS2_INTERLEAVED }, /* Toshiba Tecra A11-11L */
snprintf(priv->phys, sizeof(priv->phys), "%s/input1", psmouse->ps2dev.serio->phys);
dev2->phys = priv->phys;
dev2->name = (priv->flags & ALPS_DUALPOINT) ?
- "DualPoint Stick" : "PS/2 Mouse";
+ "DualPoint Stick" : "ALPS PS/2 Device";
dev2->id.bustype = BUS_I8042;
dev2->id.vendor = 0x0002;
dev2->id.product = PSMOUSE_ALPS;
case 2: return 5;
default:
/* Invalid contact (e.g. palm). Ignore it. */
- return -1;
+ return 0;
}
}
{
unsigned char *packet = psmouse->packet;
unsigned char header_byte = packet[0];
- int contact_cnt;
memset(report_data, 0, sizeof(struct cytp_report_data));
- contact_cnt = cypress_get_finger_count(header_byte);
-
- if (contact_cnt < 0) /* e.g. palm detect */
- return -EINVAL;
-
- report_data->contact_cnt = contact_cnt;
-
+ report_data->contact_cnt = cypress_get_finger_count(header_byte);
report_data->tap = (header_byte & ABS_MULTIFINGER_TAP) ? 1 : 0;
if (report_data->contact_cnt == 1) {
int slots[CYTP_MAX_MT_SLOTS];
int n;
- if (cypress_parse_packet(psmouse, cytp, &report_data))
- return;
+ cypress_parse_packet(psmouse, cytp, &report_data);
n = report_data.contact_cnt;
-
if (n > CYTP_MAX_MT_SLOTS)
n = CYTP_MAX_MT_SLOTS;
return PSMOUSE_BAD_DATA;
contact_cnt = cypress_get_finger_count(packet[0]);
-
- if (contact_cnt < 0)
- return PSMOUSE_BAD_DATA;
-
if (cytp->mode & CYTP_BIT_ABS_NO_PRESSURE)
cypress_set_packet_size(psmouse, contact_cnt == 2 ? 7 : 4);
else
{
struct cytp_data *cytp;
- cytp = (struct cytp_data *)kzalloc(sizeof(struct cytp_data), GFP_KERNEL);
- psmouse->private = (void *)cytp;
- if (cytp == NULL)
+ cytp = kzalloc(sizeof(struct cytp_data), GFP_KERNEL);
+ if (!cytp)
return -ENOMEM;
- cypress_reset(psmouse);
-
+ psmouse->private = cytp;
psmouse->pktsize = 8;
+ cypress_reset(psmouse);
+
if (cypress_query_hardware(psmouse)) {
psmouse_err(psmouse, "Unable to query Trackpad hardware.\n");
goto err_exit;
# Input core configuration
#
config SERIO
- tristate "Serial I/O support" if EXPERT || !X86
+ tristate "Serial I/O support"
default y
help
Say Yes here if you have any input device that uses serial I/O to
if SERIO
config SERIO_I8042
- tristate "i8042 PC Keyboard controller" if EXPERT || !X86
+ tristate "i8042 PC Keyboard controller"
default y
depends on !PARISC && (!ARM || FOOTBRIDGE_HOST) && \
(!SUPERH || SH_CAYMAN) && !M68K && !BLACKFIN && !S390 && \
module will be called maceps2.
config SERIO_LIBPS2
- tristate "PS/2 driver library" if EXPERT
+ tristate "PS/2 driver library"
depends on SERIO_I8042 || SERIO_I8042=n
help
Say Y here if you are using a driver for device connected
To compile this driver as a module, choose M here: the module will
be called olpc_apsp.
+config HYPERV_KEYBOARD
+ tristate "Microsoft Synthetic Keyboard driver"
+ depends on HYPERV
+ default HYPERV
+ help
+ Select this option to enable the Hyper-V Keyboard driver.
+
+ To compile this driver as a module, choose M here: the module will
+ be called hyperv_keyboard.
+
endif
obj-$(CONFIG_SERIO_ARC_PS2) += arc_ps2.o
obj-$(CONFIG_SERIO_APBPS2) += apbps2.o
obj-$(CONFIG_SERIO_OLPC_APSP) += olpc_apsp.o
+obj-$(CONFIG_HYPERV_KEYBOARD) += hyperv-keyboard.o
--- /dev/null
+/*
+ * Copyright (c) 2013, Microsoft Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/completion.h>
+#include <linux/hyperv.h>
+#include <linux/serio.h>
+#include <linux/slab.h>
+
+/*
+ * Current version 1.0
+ *
+ */
+#define SYNTH_KBD_VERSION_MAJOR 1
+#define SYNTH_KBD_VERSION_MINOR 0
+#define SYNTH_KBD_VERSION (SYNTH_KBD_VERSION_MINOR | \
+ (SYNTH_KBD_VERSION_MAJOR << 16))
+
+
+/*
+ * Message types in the synthetic input protocol
+ */
+enum synth_kbd_msg_type {
+ SYNTH_KBD_PROTOCOL_REQUEST = 1,
+ SYNTH_KBD_PROTOCOL_RESPONSE = 2,
+ SYNTH_KBD_EVENT = 3,
+ SYNTH_KBD_LED_INDICATORS = 4,
+};
+
+/*
+ * Basic message structures.
+ */
+struct synth_kbd_msg_hdr {
+ __le32 type;
+};
+
+struct synth_kbd_msg {
+ struct synth_kbd_msg_hdr header;
+ char data[]; /* Enclosed message */
+};
+
+union synth_kbd_version {
+ __le32 version;
+};
+
+/*
+ * Protocol messages
+ */
+struct synth_kbd_protocol_request {
+ struct synth_kbd_msg_hdr header;
+ union synth_kbd_version version_requested;
+};
+
+#define PROTOCOL_ACCEPTED BIT(0)
+struct synth_kbd_protocol_response {
+ struct synth_kbd_msg_hdr header;
+ __le32 proto_status;
+};
+
+#define IS_UNICODE BIT(0)
+#define IS_BREAK BIT(1)
+#define IS_E0 BIT(2)
+#define IS_E1 BIT(3)
+struct synth_kbd_keystroke {
+ struct synth_kbd_msg_hdr header;
+ __le16 make_code;
+ __le16 reserved0;
+ __le32 info; /* Additional information */
+};
+
+
+#define HK_MAXIMUM_MESSAGE_SIZE 256
+
+#define KBD_VSC_SEND_RING_BUFFER_SIZE (10 * PAGE_SIZE)
+#define KBD_VSC_RECV_RING_BUFFER_SIZE (10 * PAGE_SIZE)
+
+#define XTKBD_EMUL0 0xe0
+#define XTKBD_EMUL1 0xe1
+#define XTKBD_RELEASE 0x80
+
+
+/*
+ * Represents a keyboard device
+ */
+struct hv_kbd_dev {
+ struct hv_device *hv_dev;
+ struct serio *hv_serio;
+ struct synth_kbd_protocol_request protocol_req;
+ struct synth_kbd_protocol_response protocol_resp;
+ /* Synchronize the request/response if needed */
+ struct completion wait_event;
+ spinlock_t lock; /* protects 'started' field */
+ bool started;
+};
+
+static void hv_kbd_on_receive(struct hv_device *hv_dev,
+ struct synth_kbd_msg *msg, u32 msg_length)
+{
+ struct hv_kbd_dev *kbd_dev = hv_get_drvdata(hv_dev);
+ struct synth_kbd_keystroke *ks_msg;
+ unsigned long flags;
+ u32 msg_type = __le32_to_cpu(msg->header.type);
+ u32 info;
+ u16 scan_code;
+
+ switch (msg_type) {
+ case SYNTH_KBD_PROTOCOL_RESPONSE:
+ /*
+ * Validate the information provided by the host.
+ * If the host is giving us a bogus packet,
+ * drop the packet (hoping the problem
+ * goes away).
+ */
+ if (msg_length < sizeof(struct synth_kbd_protocol_response)) {
+ dev_err(&hv_dev->device,
+ "Illegal protocol response packet (len: %d)\n",
+ msg_length);
+ break;
+ }
+
+ memcpy(&kbd_dev->protocol_resp, msg,
+ sizeof(struct synth_kbd_protocol_response));
+ complete(&kbd_dev->wait_event);
+ break;
+
+ case SYNTH_KBD_EVENT:
+ /*
+ * Validate the information provided by the host.
+ * If the host is giving us a bogus packet,
+ * drop the packet (hoping the problem
+ * goes away).
+ */
+ if (msg_length < sizeof(struct synth_kbd_keystroke)) {
+ dev_err(&hv_dev->device,
+ "Illegal keyboard event packet (len: %d)\n",
+ msg_length);
+ break;
+ }
+
+ ks_msg = (struct synth_kbd_keystroke *)msg;
+ info = __le32_to_cpu(ks_msg->info);
+
+ /*
+ * Inject the information through the serio interrupt.
+ */
+ spin_lock_irqsave(&kbd_dev->lock, flags);
+ if (kbd_dev->started) {
+ if (info & IS_E0)
+ serio_interrupt(kbd_dev->hv_serio,
+ XTKBD_EMUL0, 0);
+
+ scan_code = __le16_to_cpu(ks_msg->make_code);
+ if (info & IS_BREAK)
+ scan_code |= XTKBD_RELEASE;
+
+ serio_interrupt(kbd_dev->hv_serio, scan_code, 0);
+ }
+ spin_unlock_irqrestore(&kbd_dev->lock, flags);
+ break;
+
+ default:
+ dev_err(&hv_dev->device,
+ "unhandled message type %d\n", msg_type);
+ }
+}
+
+static void hv_kbd_handle_received_packet(struct hv_device *hv_dev,
+ struct vmpacket_descriptor *desc,
+ u32 bytes_recvd,
+ u64 req_id)
+{
+ struct synth_kbd_msg *msg;
+ u32 msg_sz;
+
+ switch (desc->type) {
+ case VM_PKT_COMP:
+ break;
+
+ case VM_PKT_DATA_INBAND:
+ /*
+ * We have a packet that has "inband" data. The API used
+ * for retrieving the packet guarantees that the complete
+ * packet is read. So, minimally, we should be able to
+ * parse the payload header safely (assuming that the host
+ * can be trusted. Trusting the host seems to be a
+ * reasonable assumption because in a virtualized
+ * environment there is not whole lot you can do if you
+ * don't trust the host.
+ *
+ * Nonetheless, let us validate if the host can be trusted
+ * (in a trivial way). The interesting aspect of this
+ * validation is how do you recover if we discover that the
+ * host is not to be trusted? Simply dropping the packet, I
+ * don't think is an appropriate recovery. In the interest
+ * of failing fast, it may be better to crash the guest.
+ * For now, I will just drop the packet!
+ */
+
+ msg_sz = bytes_recvd - (desc->offset8 << 3);
+ if (msg_sz <= sizeof(struct synth_kbd_msg_hdr)) {
+ /*
+ * Drop the packet and hope
+ * the problem magically goes away.
+ */
+ dev_err(&hv_dev->device,
+ "Illegal packet (type: %d, tid: %llx, size: %d)\n",
+ desc->type, req_id, msg_sz);
+ break;
+ }
+
+ msg = (void *)desc + (desc->offset8 << 3);
+ hv_kbd_on_receive(hv_dev, msg, msg_sz);
+ break;
+
+ default:
+ dev_err(&hv_dev->device,
+ "unhandled packet type %d, tid %llx len %d\n",
+ desc->type, req_id, bytes_recvd);
+ break;
+ }
+}
+
+static void hv_kbd_on_channel_callback(void *context)
+{
+ struct hv_device *hv_dev = context;
+ void *buffer;
+ int bufferlen = 0x100; /* Start with sensible size */
+ u32 bytes_recvd;
+ u64 req_id;
+ int error;
+
+ buffer = kmalloc(bufferlen, GFP_ATOMIC);
+ if (!buffer)
+ return;
+
+ while (1) {
+ error = vmbus_recvpacket_raw(hv_dev->channel, buffer, bufferlen,
+ &bytes_recvd, &req_id);
+ switch (error) {
+ case 0:
+ if (bytes_recvd == 0) {
+ kfree(buffer);
+ return;
+ }
+
+ hv_kbd_handle_received_packet(hv_dev, buffer,
+ bytes_recvd, req_id);
+ break;
+
+ case -ENOBUFS:
+ kfree(buffer);
+ /* Handle large packet */
+ bufferlen = bytes_recvd;
+ buffer = kmalloc(bytes_recvd, GFP_ATOMIC);
+ if (!buffer)
+ return;
+ break;
+ }
+ }
+}
+
+static int hv_kbd_connect_to_vsp(struct hv_device *hv_dev)
+{
+ struct hv_kbd_dev *kbd_dev = hv_get_drvdata(hv_dev);
+ struct synth_kbd_protocol_request *request;
+ struct synth_kbd_protocol_response *response;
+ u32 proto_status;
+ int error;
+
+ request = &kbd_dev->protocol_req;
+ memset(request, 0, sizeof(struct synth_kbd_protocol_request));
+ request->header.type = __cpu_to_le32(SYNTH_KBD_PROTOCOL_REQUEST);
+ request->version_requested.version = __cpu_to_le32(SYNTH_KBD_VERSION);
+
+ error = vmbus_sendpacket(hv_dev->channel, request,
+ sizeof(struct synth_kbd_protocol_request),
+ (unsigned long)request,
+ VM_PKT_DATA_INBAND,
+ VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED);
+ if (error)
+ return error;
+
+ if (!wait_for_completion_timeout(&kbd_dev->wait_event, 10 * HZ))
+ return -ETIMEDOUT;
+
+ response = &kbd_dev->protocol_resp;
+ proto_status = __le32_to_cpu(response->proto_status);
+ if (!(proto_status & PROTOCOL_ACCEPTED)) {
+ dev_err(&hv_dev->device,
+ "synth_kbd protocol request failed (version %d)\n",
+ SYNTH_KBD_VERSION);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int hv_kbd_start(struct serio *serio)
+{
+ struct hv_kbd_dev *kbd_dev = serio->port_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&kbd_dev->lock, flags);
+ kbd_dev->started = true;
+ spin_unlock_irqrestore(&kbd_dev->lock, flags);
+
+ return 0;
+}
+
+static void hv_kbd_stop(struct serio *serio)
+{
+ struct hv_kbd_dev *kbd_dev = serio->port_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&kbd_dev->lock, flags);
+ kbd_dev->started = false;
+ spin_unlock_irqrestore(&kbd_dev->lock, flags);
+}
+
+static int hv_kbd_probe(struct hv_device *hv_dev,
+ const struct hv_vmbus_device_id *dev_id)
+{
+ struct hv_kbd_dev *kbd_dev;
+ struct serio *hv_serio;
+ int error;
+
+ kbd_dev = kzalloc(sizeof(struct hv_kbd_dev), GFP_KERNEL);
+ hv_serio = kzalloc(sizeof(struct serio), GFP_KERNEL);
+ if (!kbd_dev || !hv_serio) {
+ error = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ kbd_dev->hv_dev = hv_dev;
+ kbd_dev->hv_serio = hv_serio;
+ spin_lock_init(&kbd_dev->lock);
+ init_completion(&kbd_dev->wait_event);
+ hv_set_drvdata(hv_dev, kbd_dev);
+
+ hv_serio->dev.parent = &hv_dev->device;
+ hv_serio->id.type = SERIO_8042_XL;
+ hv_serio->port_data = kbd_dev;
+ strlcpy(hv_serio->name, dev_name(&hv_dev->device),
+ sizeof(hv_serio->name));
+ strlcpy(hv_serio->phys, dev_name(&hv_dev->device),
+ sizeof(hv_serio->phys));
+
+ hv_serio->start = hv_kbd_start;
+ hv_serio->stop = hv_kbd_stop;
+
+ error = vmbus_open(hv_dev->channel,
+ KBD_VSC_SEND_RING_BUFFER_SIZE,
+ KBD_VSC_RECV_RING_BUFFER_SIZE,
+ NULL, 0,
+ hv_kbd_on_channel_callback,
+ hv_dev);
+ if (error)
+ goto err_free_mem;
+
+ error = hv_kbd_connect_to_vsp(hv_dev);
+ if (error)
+ goto err_close_vmbus;
+
+ serio_register_port(kbd_dev->hv_serio);
+ return 0;
+
+err_close_vmbus:
+ vmbus_close(hv_dev->channel);
+err_free_mem:
+ kfree(hv_serio);
+ kfree(kbd_dev);
+ return error;
+}
+
+static int hv_kbd_remove(struct hv_device *hv_dev)
+{
+ struct hv_kbd_dev *kbd_dev = hv_get_drvdata(hv_dev);
+
+ serio_unregister_port(kbd_dev->hv_serio);
+ vmbus_close(hv_dev->channel);
+ kfree(kbd_dev);
+
+ hv_set_drvdata(hv_dev, NULL);
+
+ return 0;
+}
+
+/*
+ * Keyboard GUID
+ * {f912ad6d-2b17-48ea-bd65-f927a61c7684}
+ */
+#define HV_KBD_GUID \
+ .guid = { \
+ 0x6d, 0xad, 0x12, 0xf9, 0x17, 0x2b, 0xea, 0x48, \
+ 0xbd, 0x65, 0xf9, 0x27, 0xa6, 0x1c, 0x76, 0x84 \
+ }
+
+static const struct hv_vmbus_device_id id_table[] = {
+ /* Keyboard guid */
+ { HV_KBD_GUID, },
+ { },
+};
+
+MODULE_DEVICE_TABLE(vmbus, id_table);
+
+static struct hv_driver hv_kbd_drv = {
+ .name = KBUILD_MODNAME,
+ .id_table = id_table,
+ .probe = hv_kbd_probe,
+ .remove = hv_kbd_remove,
+};
+
+static int __init hv_kbd_init(void)
+{
+ return vmbus_driver_register(&hv_kbd_drv);
+}
+
+static void __exit hv_kbd_exit(void)
+{
+ vmbus_driver_unregister(&hv_kbd_drv);
+}
+
+MODULE_LICENSE("GPL");
+module_init(hv_kbd_init);
+module_exit(hv_kbd_exit);
{ .id = "CPQA0D7", .driver_data = 0 },
{ .id = "", },
};
+MODULE_DEVICE_TABLE(pnp, pnp_kbd_devids);
static struct pnp_driver i8042_pnp_kbd_driver = {
.name = "i8042 kbd",
{ .id = "SYN0801", .driver_data = 0 },
{ .id = "", },
};
+MODULE_DEVICE_TABLE(pnp, pnp_aux_devids);
static struct pnp_driver i8042_pnp_aux_driver = {
.name = "i8042 aux",
error = wacom_set_report(intf, WAC_HID_FEATURE_REPORT,
report_id, rep_data, length, 1);
- if (error >= 0)
- error = wacom_get_report(intf, WAC_HID_FEATURE_REPORT,
- report_id, rep_data, length, 1);
} while ((error < 0 || rep_data[1] != mode) && limit++ < WAC_MSG_RETRIES);
kfree(rep_data);
/* MT Tablet PC touch */
return wacom_set_device_mode(intf, 3, 4, 4);
}
- else if (features->type == WACOM_24HDT) {
+ else if (features->type == WACOM_24HDT || features->type == CINTIQ_HYBRID) {
return wacom_set_device_mode(intf, 18, 3, 2);
}
} else if (features->device_type == BTN_TOOL_PEN) {
return -ENOMEM;
if (wacom->wacom_wac.features.type >= INTUOS5S &&
- wacom->wacom_wac.features.type <= INTUOS5L) {
+ wacom->wacom_wac.features.type <= INTUOSPL) {
/*
* Touch Ring and crop mark LED luminance may take on
* one of four values:
case INTUOS5S:
case INTUOS5:
case INTUOS5L:
- wacom->led.select[0] = 0;
- wacom->led.select[1] = 0;
- wacom->led.llv = 32;
- wacom->led.hlv = 0;
- wacom->led.img_lum = 0;
-
- error = sysfs_create_group(&wacom->intf->dev.kobj,
- &intuos5_led_attr_group);
+ case INTUOSPS:
+ case INTUOSPM:
+ case INTUOSPL:
+ if (wacom->wacom_wac.features.device_type == BTN_TOOL_PEN) {
+ wacom->led.select[0] = 0;
+ wacom->led.select[1] = 0;
+ wacom->led.llv = 32;
+ wacom->led.hlv = 0;
+ wacom->led.img_lum = 0;
+
+ error = sysfs_create_group(&wacom->intf->dev.kobj,
+ &intuos5_led_attr_group);
+ } else
+ return 0;
break;
default:
case INTUOS5S:
case INTUOS5:
case INTUOS5L:
- sysfs_remove_group(&wacom->intf->dev.kobj,
- &intuos5_led_attr_group);
+ case INTUOSPS:
+ case INTUOSPM:
+ case INTUOSPL:
+ if (wacom->wacom_wac.features.device_type == BTN_TOOL_PEN)
+ sysfs_remove_group(&wacom->intf->dev.kobj,
+ &intuos5_led_attr_group);
break;
}
}
wacom_wac1->features =
*((struct wacom_features *)id->driver_info);
wacom_wac1->features.device_type = BTN_TOOL_PEN;
+ snprintf(wacom_wac1->name, WACOM_NAME_MAX, "%s (WL) Pen",
+ wacom_wac1->features.name);
error = wacom_register_input(wacom1);
if (error)
- goto fail1;
+ goto fail;
/* Touch interface */
- wacom_wac2->features =
- *((struct wacom_features *)id->driver_info);
- wacom_wac2->features.pktlen = WACOM_PKGLEN_BBTOUCH3;
- wacom_wac2->features.device_type = BTN_TOOL_FINGER;
- wacom_wac2->features.x_max = wacom_wac2->features.y_max = 4096;
- error = wacom_register_input(wacom2);
- if (error)
- goto fail2;
+ if (wacom_wac1->features.touch_max) {
+ wacom_wac2->features =
+ *((struct wacom_features *)id->driver_info);
+ wacom_wac2->features.pktlen = WACOM_PKGLEN_BBTOUCH3;
+ wacom_wac2->features.device_type = BTN_TOOL_FINGER;
+ wacom_wac2->features.x_max = wacom_wac2->features.y_max = 4096;
+ if (wacom_wac2->features.touch_max)
+ snprintf(wacom_wac2->name, WACOM_NAME_MAX,
+ "%s (WL) Finger",wacom_wac2->features.name);
+ else
+ snprintf(wacom_wac2->name, WACOM_NAME_MAX,
+ "%s (WL) Pad",wacom_wac2->features.name);
+ error = wacom_register_input(wacom2);
+ if (error)
+ goto fail;
+ }
error = wacom_initialize_battery(wacom);
if (error)
- goto fail3;
+ goto fail;
}
return;
-fail3:
- input_unregister_device(wacom_wac2->input);
- wacom_wac2->input = NULL;
-fail2:
- input_unregister_device(wacom_wac1->input);
- wacom_wac1->input = NULL;
-fail1:
+fail:
+ if (wacom_wac2->input) {
+ input_unregister_device(wacom_wac2->input);
+ wacom_wac2->input = NULL;
+ }
+
+ if (wacom_wac1->input) {
+ input_unregister_device(wacom_wac1->input);
+ wacom_wac1->input = NULL;
+ }
return;
}
* HID descriptor. If this is the touch interface (wMaxPacketSize
* of WACOM_PKGLEN_BBTOUCH3), override the table values.
*/
- if (features->type >= INTUOS5S && features->type <= INTUOS5L) {
+ if (features->type >= INTUOS5S && features->type <= INTUOSPL) {
if (endpoint->wMaxPacketSize == WACOM_PKGLEN_BBTOUCH3) {
features->device_type = BTN_TOOL_FINGER;
features->pktlen = WACOM_PKGLEN_BBTOUCH3;
struct usb_device *other_dev;
/* Append the device type to the name */
- strlcat(wacom_wac->name,
- features->device_type == BTN_TOOL_PEN ?
- " Pen" : " Finger",
- sizeof(wacom_wac->name));
+ if (features->device_type != BTN_TOOL_FINGER)
+ strlcat(wacom_wac->name, " Pen", WACOM_NAME_MAX);
+ else if (features->touch_max)
+ strlcat(wacom_wac->name, " Finger", WACOM_NAME_MAX);
+ else
+ strlcat(wacom_wac->name, " Pad", WACOM_NAME_MAX);
other_dev = wacom_get_sibling(dev, features->oVid, features->oPid);
if (other_dev == NULL || wacom_get_usbdev_data(other_dev) == NULL)
(features->type == WACOM_21UX2))
return 1;
+ /* Range Report */
+ if ((data[1] & 0xfe) == 0x20) {
+ input_report_key(input, BTN_TOUCH, 0);
+ input_report_abs(input, ABS_PRESSURE, 0);
+ input_report_abs(input, ABS_DISTANCE, wacom->features.distance_max);
+ }
+
/* Exit report */
if ((data[1] & 0xfe) == 0x80) {
if (features->quirks == WACOM_QUIRK_MULTI_INPUT)
/* general pen packet */
if ((data[1] & 0xb8) == 0xa0) {
t = (data[6] << 2) | ((data[7] >> 6) & 3);
- if (features->type >= INTUOS4S && features->type <= WACOM_24HD) {
+ if (features->type >= INTUOS4S && features->type <= CINTIQ_HYBRID) {
t = (t << 1) | (data[1] & 1);
}
input_report_abs(input, ABS_PRESSURE, t);
} else {
input_report_abs(input, ABS_MISC, 0);
}
- } else if (features->type >= INTUOS5S && features->type <= INTUOS5L) {
+ } else if (features->type == CINTIQ_HYBRID) {
+ /*
+ * Do not send hardware buttons under Android. They
+ * are already sent to the system through GPIO (and
+ * have different meaning).
+ */
+ input_report_key(input, BTN_1, (data[4] & 0x01));
+ input_report_key(input, BTN_2, (data[4] & 0x02));
+ input_report_key(input, BTN_3, (data[4] & 0x04));
+ input_report_key(input, BTN_4, (data[4] & 0x08));
+
+ input_report_key(input, BTN_5, (data[4] & 0x10)); /* Right */
+ input_report_key(input, BTN_6, (data[4] & 0x20)); /* Up */
+ input_report_key(input, BTN_7, (data[4] & 0x40)); /* Left */
+ input_report_key(input, BTN_8, (data[4] & 0x80)); /* Down */
+ input_report_key(input, BTN_0, (data[3] & 0x01)); /* Center */
+ } else if (features->type >= INTUOS5S && features->type <= INTUOSPL) {
int i;
/* Touch ring mode switch has no capacitive sensor */
input_report_key(input, BTN_0, (data[3] & 0x01));
/*
- * ExpressKeys on Intuos5 have a capacitive sensor in
+ * ExpressKeys on Intuos5/Intuos Pro have a capacitive sensor in
* addition to the mechanical switch. Switch data is
* stored in data[4], capacitive data in data[5].
*/
features->type == INTUOS4 ||
features->type == INTUOS4S ||
features->type == INTUOS5 ||
- features->type == INTUOS5S)) {
+ features->type == INTUOS5S ||
+ features->type == INTUOSPM ||
+ features->type == INTUOSPS)) {
return 0;
}
} else if (wacom->tool[idx] == BTN_TOOL_MOUSE) {
/* I4 mouse */
- if ((features->type >= INTUOS4S && features->type <= INTUOS4L) ||
- (features->type >= INTUOS5S && features->type <= INTUOS5L)) {
+ if (features->type >= INTUOS4S && features->type <= INTUOSPL) {
input_report_key(input, BTN_LEFT, data[6] & 0x01);
input_report_key(input, BTN_MIDDLE, data[6] & 0x02);
input_report_key(input, BTN_RIGHT, data[6] & 0x04);
}
}
} else if ((features->type < INTUOS3S || features->type == INTUOS3L ||
- features->type == INTUOS4L || features->type == INTUOS5L) &&
+ features->type == INTUOS4L || features->type == INTUOS5L ||
+ features->type == INTUOSPL) &&
wacom->tool[idx] == BTN_TOOL_LENS) {
/* Lens cursor packets */
input_report_key(input, BTN_LEFT, data[8] & 0x01);
static void wacom_bpt3_touch_msg(struct wacom_wac *wacom, unsigned char *data)
{
+ struct wacom_features *features = &wacom->features;
struct input_dev *input = wacom->input;
bool touch = data[1] & 0x80;
int slot = input_mt_get_slot_by_key(input, data[0]);
if (touch) {
int x = (data[2] << 4) | (data[4] >> 4);
int y = (data[3] << 4) | (data[4] & 0x0f);
- int a = data[5];
+ int width, height;
- // "a" is a scaled-down area which we assume is roughly
- // circular and which can be described as: a=(pi*r^2)/C.
- int x_res = input_abs_get_res(input, ABS_X);
- int y_res = input_abs_get_res(input, ABS_Y);
- int width = 2 * int_sqrt(a * WACOM_CONTACT_AREA_SCALE);
- int height = width * y_res / x_res;
+ if (features->type >= INTUOSPS && features->type <= INTUOSPL) {
+ width = data[5];
+ height = data[6];
+ } else {
+ /*
+ * "a" is a scaled-down area which we assume is
+ * roughly circular and which can be described as:
+ * a=(pi*r^2)/C.
+ */
+ int a = data[5];
+ int x_res = input_abs_get_res(input, ABS_X);
+ int y_res = input_abs_get_res(input, ABS_Y);
+ width = 2 * int_sqrt(a * WACOM_CONTACT_AREA_SCALE);
+ height = width * y_res / x_res;
+ }
input_report_abs(input, ABS_MT_POSITION_X, x);
input_report_abs(input, ABS_MT_POSITION_Y, y);
case WACOM_22HD:
case WACOM_24HD:
case DTK:
+ case CINTIQ_HYBRID:
sync = wacom_intuos_irq(wacom_wac);
break;
case INTUOS5S:
case INTUOS5:
case INTUOS5L:
+ case INTUOSPS:
+ case INTUOSPM:
+ case INTUOSPL:
if (len == WACOM_PKGLEN_BBTOUCH3)
sync = wacom_bpt3_touch(wacom_wac);
else
/* these device have multiple inputs */
if (features->type >= WIRELESS ||
- (features->type >= INTUOS5S && features->type <= INTUOS5L) ||
+ (features->type >= INTUOS5S && features->type <= INTUOSPL) ||
(features->oVid && features->oPid))
features->quirks |= WACOM_QUIRK_MULTI_INPUT;
case INTUOS5:
case INTUOS5L:
+ case INTUOSPM:
+ case INTUOSPL:
if (features->device_type == BTN_TOOL_PEN) {
__set_bit(BTN_7, input_dev->keybit);
__set_bit(BTN_8, input_dev->keybit);
/* fall through */
case INTUOS5S:
+ case INTUOSPS:
__set_bit(INPUT_PROP_POINTER, input_dev->propbit);
if (features->device_type == BTN_TOOL_PEN) {
0, 0);
}
break;
+
+ case CINTIQ_HYBRID:
+ __set_bit(BTN_1, input_dev->keybit);
+ __set_bit(BTN_2, input_dev->keybit);
+ __set_bit(BTN_3, input_dev->keybit);
+ __set_bit(BTN_4, input_dev->keybit);
+
+ __set_bit(BTN_5, input_dev->keybit);
+ __set_bit(BTN_6, input_dev->keybit);
+ __set_bit(BTN_7, input_dev->keybit);
+ __set_bit(BTN_8, input_dev->keybit);
+ __set_bit(BTN_0, input_dev->keybit);
+
+ input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
+ __set_bit(INPUT_PROP_DIRECT, input_dev->propbit);
+
+ wacom_setup_cintiq(wacom_wac);
+ break;
}
return 0;
}
static const struct wacom_features wacom_features_0x2A =
{ "Wacom Intuos5 M", WACOM_PKGLEN_INTUOS, 44704, 27940, 2047,
63, INTUOS5, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0x314 =
+ { "Wacom Intuos Pro S", WACOM_PKGLEN_INTUOS, 31496, 19685, 2047,
+ 63, INTUOSPS, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+ .touch_max = 16 };
+static const struct wacom_features wacom_features_0x315 =
+ { "Wacom Intuos Pro M", WACOM_PKGLEN_INTUOS, 44704, 27940, 2047,
+ 63, INTUOSPM, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+ .touch_max = 16 };
+static const struct wacom_features wacom_features_0x317 =
+ { "Wacom Intuos Pro L", WACOM_PKGLEN_INTUOS, 65024, 40640, 2047,
+ 63, INTUOSPL, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+ .touch_max = 16 };
static const struct wacom_features wacom_features_0xF4 =
{ "Wacom Cintiq 24HD", WACOM_PKGLEN_INTUOS, 104480, 65600, 2047,
63, WACOM_24HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
static const struct wacom_features wacom_features_0x6004 =
{ "ISD-V4", WACOM_PKGLEN_GRAPHIRE, 12800, 8000, 255,
0, TABLETPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
+static const struct wacom_features wacom_features_0x0307 =
+ { "Wacom ISDv5 307", WACOM_PKGLEN_INTUOS, 59552, 33848, 2047,
+ 63, CINTIQ_HYBRID, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES,
+ .oVid = USB_VENDOR_ID_WACOM, .oPid = 0x309 };
+static const struct wacom_features wacom_features_0x0309 =
+ { "Wacom ISDv5 309", .type = WACOM_24HDT, /* Touch */
+ .oVid = USB_VENDOR_ID_WACOM, .oPid = 0x0307, .touch_max = 10 };
#define USB_DEVICE_WACOM(prod) \
USB_DEVICE(USB_VENDOR_ID_WACOM, prod), \
{ USB_DEVICE_WACOM(0x300) },
{ USB_DEVICE_WACOM(0x301) },
{ USB_DEVICE_WACOM(0x304) },
+ { USB_DEVICE_DETAILED(0x314, USB_CLASS_HID, 0, 0) },
+ { USB_DEVICE_DETAILED(0x315, USB_CLASS_HID, 0, 0) },
+ { USB_DEVICE_DETAILED(0x317, USB_CLASS_HID, 0, 0) },
{ USB_DEVICE_WACOM(0x4001) },
{ USB_DEVICE_WACOM(0x47) },
{ USB_DEVICE_WACOM(0xF4) },
{ USB_DEVICE_WACOM(0xF8) },
{ USB_DEVICE_DETAILED(0xF6, USB_CLASS_HID, 0, 0) },
{ USB_DEVICE_WACOM(0xFA) },
+ { USB_DEVICE_WACOM(0x0307) },
+ { USB_DEVICE_DETAILED(0x0309, USB_CLASS_HID, 0, 0) },
{ USB_DEVICE_LENOVO(0x6004) },
{ }
};
/* maximum packet length for USB devices */
#define WACOM_PKGLEN_MAX 64
+#define WACOM_NAME_MAX 64
+
/* packet length for individual models */
#define WACOM_PKGLEN_PENPRTN 7
#define WACOM_PKGLEN_GRAPHIRE 8
INTUOS5S,
INTUOS5,
INTUOS5L,
+ INTUOSPS,
+ INTUOSPM,
+ INTUOSPL,
WACOM_21UX2,
WACOM_22HD,
DTK,
WACOM_24HD,
+ CINTIQ_HYBRID,
CINTIQ,
WACOM_BEE,
WACOM_13HD,
};
struct wacom_wac {
- char name[64];
+ char name[WACOM_NAME_MAX];
unsigned char *data;
int tool[2];
int id[2];
To compile this driver as a module, choose M here: the
module will be called tps6507x_ts.
+config TOUCHSCREEN_ZFORCE
+ tristate "Neonode zForce infrared touchscreens"
+ depends on I2C
+ depends on GPIOLIB
+ help
+ Say Y here if you have a touchscreen using the zforce
+ infraread technology from Neonode.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called zforce_ts.
+
endif
obj-$(CONFIG_TOUCHSCREEN_WM97XX_ZYLONITE) += zylonite-wm97xx.o
obj-$(CONFIG_TOUCHSCREEN_W90X900) += w90p910_ts.o
obj-$(CONFIG_TOUCHSCREEN_TPS6507X) += tps6507x-ts.o
+obj-$(CONFIG_TOUCHSCREEN_ZFORCE) += zforce_ts.o
err_free_mem:
input_free_device(input_dev);
kfree(ts);
- spi_set_drvdata(spi, NULL);
return err;
}
kfree(ts);
dev_dbg(&spi->dev, "unregistered touchscreen\n");
- spi_set_drvdata(spi, NULL);
return 0;
}
struct ad7879 *ts = spi_get_drvdata(spi);
ad7879_remove(ts);
- spi_set_drvdata(spi, NULL);
return 0;
}
error_request_irq:
if (cd->cpdata->init)
cd->cpdata->init(cd->cpdata, 0, dev);
- dev_set_drvdata(dev, NULL);
error_free_xfer:
kfree(cd->xfer_buf);
error_free_cd:
free_irq(cd->irq, cd);
if (cd->cpdata->init)
cd->cpdata->init(cd->cpdata, 0, dev);
- dev_set_drvdata(dev, NULL);
cyttsp4_free_si_ptrs(cd);
kfree(cd);
return 0;
ts = cyttsp4_probe(&cyttsp_spi_bus_ops, &spi->dev, spi->irq,
CY_SPI_DATA_BUF_SIZE);
- if (IS_ERR(ts))
- return PTR_ERR(ts);
-
- return 0;
+ return PTR_ERR_OR_ZERO(ts);
}
static int cyttsp4_spi_remove(struct spi_device *spi)
.name = "egalax_ts",
.owner = THIS_MODULE,
.pm = &egalax_ts_pm_ops,
- .of_match_table = of_match_ptr(egalax_ts_dt_ids),
+ .of_match_table = egalax_ts_dt_ids,
},
.id_table = egalax_ts_id,
.probe = egalax_ts_probe,
release_region(HTCPEN_PORT_INIT, 1);
release_region(HTCPEN_PORT_IRQ_CLEAR, 1);
- dev_set_drvdata(dev, NULL);
-
return 0;
}
#include <linux/input.h>
#include <linux/interrupt.h>
#include <linux/module.h>
+#include <linux/of.h>
#include <linux/of_gpio.h>
#include <linux/pm_qos.h>
#include <linux/slab.h>
if (err < 0)
return err;
- err = of_property_read_u32(node, "ti,coordiante-readouts",
+ /*
+ * Try with the new binding first. If it fails, try again with
+ * bogus, miss-spelled version.
+ */
+ err = of_property_read_u32(node, "ti,coordinate-readouts",
&ts_dev->coordinate_readouts);
+ if (err < 0)
+ err = of_property_read_u32(node, "ti,coordiante-readouts",
+ &ts_dev->coordinate_readouts);
if (err < 0)
return err;
.name = "TI-am335x-tsc",
.owner = THIS_MODULE,
.pm = TITSC_PM_OPS,
- .of_match_table = of_match_ptr(ti_tsc_dt_ids),
+ .of_match_table = ti_tsc_dt_ids,
},
};
module_platform_driver(ti_tsc_driver);
err_remove_sysfs:
sysfs_remove_group(&spi->dev.kobj, &tsc2005_attr_group);
err_clear_drvdata:
- spi_set_drvdata(spi, NULL);
free_irq(spi->irq, ts);
err_free_mem:
input_free_device(input_dev);
input_unregister_device(ts->idev);
kfree(ts);
- spi_set_drvdata(spi, NULL);
return 0;
}
--- /dev/null
+/*
+ * Copyright (C) 2012-2013 MundoReader S.L.
+ * Author: Heiko Stuebner <heiko@sntech.de>
+ *
+ * based in parts on Nook zforce driver
+ *
+ * Copyright (C) 2010 Barnes & Noble, Inc.
+ * Author: Pieter Truter<ptruter@intrinsyc.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/hrtimer.h>
+#include <linux/slab.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/device.h>
+#include <linux/sysfs.h>
+#include <linux/input/mt.h>
+#include <linux/platform_data/zforce_ts.h>
+
+#define WAIT_TIMEOUT msecs_to_jiffies(1000)
+
+#define FRAME_START 0xee
+
+/* Offsets of the different parts of the payload the controller sends */
+#define PAYLOAD_HEADER 0
+#define PAYLOAD_LENGTH 1
+#define PAYLOAD_BODY 2
+
+/* Response offsets */
+#define RESPONSE_ID 0
+#define RESPONSE_DATA 1
+
+/* Commands */
+#define COMMAND_DEACTIVATE 0x00
+#define COMMAND_INITIALIZE 0x01
+#define COMMAND_RESOLUTION 0x02
+#define COMMAND_SETCONFIG 0x03
+#define COMMAND_DATAREQUEST 0x04
+#define COMMAND_SCANFREQ 0x08
+#define COMMAND_STATUS 0X1e
+
+/*
+ * Responses the controller sends as a result of
+ * command requests
+ */
+#define RESPONSE_DEACTIVATE 0x00
+#define RESPONSE_INITIALIZE 0x01
+#define RESPONSE_RESOLUTION 0x02
+#define RESPONSE_SETCONFIG 0x03
+#define RESPONSE_SCANFREQ 0x08
+#define RESPONSE_STATUS 0X1e
+
+/*
+ * Notifications are send by the touch controller without
+ * being requested by the driver and include for example
+ * touch indications
+ */
+#define NOTIFICATION_TOUCH 0x04
+#define NOTIFICATION_BOOTCOMPLETE 0x07
+#define NOTIFICATION_OVERRUN 0x25
+#define NOTIFICATION_PROXIMITY 0x26
+#define NOTIFICATION_INVALID_COMMAND 0xfe
+
+#define ZFORCE_REPORT_POINTS 2
+#define ZFORCE_MAX_AREA 0xff
+
+#define STATE_DOWN 0
+#define STATE_MOVE 1
+#define STATE_UP 2
+
+#define SETCONFIG_DUALTOUCH (1 << 0)
+
+struct zforce_point {
+ int coord_x;
+ int coord_y;
+ int state;
+ int id;
+ int area_major;
+ int area_minor;
+ int orientation;
+ int pressure;
+ int prblty;
+};
+
+/*
+ * @client the i2c_client
+ * @input the input device
+ * @suspending in the process of going to suspend (don't emit wakeup
+ * events for commands executed to suspend the device)
+ * @suspended device suspended
+ * @access_mutex serialize i2c-access, to keep multipart reads together
+ * @command_done completion to wait for the command result
+ * @command_mutex serialize commands send to the ic
+ * @command_waiting the id of the command that that is currently waiting
+ * for a result
+ * @command_result returned result of the command
+ */
+struct zforce_ts {
+ struct i2c_client *client;
+ struct input_dev *input;
+ const struct zforce_ts_platdata *pdata;
+ char phys[32];
+
+ bool suspending;
+ bool suspended;
+ bool boot_complete;
+
+ /* Firmware version information */
+ u16 version_major;
+ u16 version_minor;
+ u16 version_build;
+ u16 version_rev;
+
+ struct mutex access_mutex;
+
+ struct completion command_done;
+ struct mutex command_mutex;
+ int command_waiting;
+ int command_result;
+};
+
+static int zforce_command(struct zforce_ts *ts, u8 cmd)
+{
+ struct i2c_client *client = ts->client;
+ char buf[3];
+ int ret;
+
+ dev_dbg(&client->dev, "%s: 0x%x\n", __func__, cmd);
+
+ buf[0] = FRAME_START;
+ buf[1] = 1; /* data size, command only */
+ buf[2] = cmd;
+
+ mutex_lock(&ts->access_mutex);
+ ret = i2c_master_send(client, &buf[0], ARRAY_SIZE(buf));
+ mutex_unlock(&ts->access_mutex);
+ if (ret < 0) {
+ dev_err(&client->dev, "i2c send data request error: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int zforce_send_wait(struct zforce_ts *ts, const char *buf, int len)
+{
+ struct i2c_client *client = ts->client;
+ int ret;
+
+ ret = mutex_trylock(&ts->command_mutex);
+ if (!ret) {
+ dev_err(&client->dev, "already waiting for a command\n");
+ return -EBUSY;
+ }
+
+ dev_dbg(&client->dev, "sending %d bytes for command 0x%x\n",
+ buf[1], buf[2]);
+
+ ts->command_waiting = buf[2];
+
+ mutex_lock(&ts->access_mutex);
+ ret = i2c_master_send(client, buf, len);
+ mutex_unlock(&ts->access_mutex);
+ if (ret < 0) {
+ dev_err(&client->dev, "i2c send data request error: %d\n", ret);
+ goto unlock;
+ }
+
+ dev_dbg(&client->dev, "waiting for result for command 0x%x\n", buf[2]);
+
+ if (wait_for_completion_timeout(&ts->command_done, WAIT_TIMEOUT) == 0) {
+ ret = -ETIME;
+ goto unlock;
+ }
+
+ ret = ts->command_result;
+
+unlock:
+ mutex_unlock(&ts->command_mutex);
+ return ret;
+}
+
+static int zforce_command_wait(struct zforce_ts *ts, u8 cmd)
+{
+ struct i2c_client *client = ts->client;
+ char buf[3];
+ int ret;
+
+ dev_dbg(&client->dev, "%s: 0x%x\n", __func__, cmd);
+
+ buf[0] = FRAME_START;
+ buf[1] = 1; /* data size, command only */
+ buf[2] = cmd;
+
+ ret = zforce_send_wait(ts, &buf[0], ARRAY_SIZE(buf));
+ if (ret < 0) {
+ dev_err(&client->dev, "i2c send data request error: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int zforce_resolution(struct zforce_ts *ts, u16 x, u16 y)
+{
+ struct i2c_client *client = ts->client;
+ char buf[7] = { FRAME_START, 5, COMMAND_RESOLUTION,
+ (x & 0xff), ((x >> 8) & 0xff),
+ (y & 0xff), ((y >> 8) & 0xff) };
+
+ dev_dbg(&client->dev, "set resolution to (%d,%d)\n", x, y);
+
+ return zforce_send_wait(ts, &buf[0], ARRAY_SIZE(buf));
+}
+
+static int zforce_scan_frequency(struct zforce_ts *ts, u16 idle, u16 finger,
+ u16 stylus)
+{
+ struct i2c_client *client = ts->client;
+ char buf[9] = { FRAME_START, 7, COMMAND_SCANFREQ,
+ (idle & 0xff), ((idle >> 8) & 0xff),
+ (finger & 0xff), ((finger >> 8) & 0xff),
+ (stylus & 0xff), ((stylus >> 8) & 0xff) };
+
+ dev_dbg(&client->dev, "set scan frequency to (idle: %d, finger: %d, stylus: %d)\n",
+ idle, finger, stylus);
+
+ return zforce_send_wait(ts, &buf[0], ARRAY_SIZE(buf));
+}
+
+static int zforce_setconfig(struct zforce_ts *ts, char b1)
+{
+ struct i2c_client *client = ts->client;
+ char buf[7] = { FRAME_START, 5, COMMAND_SETCONFIG,
+ b1, 0, 0, 0 };
+
+ dev_dbg(&client->dev, "set config to (%d)\n", b1);
+
+ return zforce_send_wait(ts, &buf[0], ARRAY_SIZE(buf));
+}
+
+static int zforce_start(struct zforce_ts *ts)
+{
+ struct i2c_client *client = ts->client;
+ const struct zforce_ts_platdata *pdata = dev_get_platdata(&client->dev);
+ int ret;
+
+ dev_dbg(&client->dev, "starting device\n");
+
+ ret = zforce_command_wait(ts, COMMAND_INITIALIZE);
+ if (ret) {
+ dev_err(&client->dev, "Unable to initialize, %d\n", ret);
+ return ret;
+ }
+
+ ret = zforce_resolution(ts, pdata->x_max, pdata->y_max);
+ if (ret) {
+ dev_err(&client->dev, "Unable to set resolution, %d\n", ret);
+ goto error;
+ }
+
+ ret = zforce_scan_frequency(ts, 10, 50, 50);
+ if (ret) {
+ dev_err(&client->dev, "Unable to set scan frequency, %d\n",
+ ret);
+ goto error;
+ }
+
+ if (zforce_setconfig(ts, SETCONFIG_DUALTOUCH)) {
+ dev_err(&client->dev, "Unable to set config\n");
+ goto error;
+ }
+
+ /* start sending touch events */
+ ret = zforce_command(ts, COMMAND_DATAREQUEST);
+ if (ret) {
+ dev_err(&client->dev, "Unable to request data\n");
+ goto error;
+ }
+
+ /*
+ * Per NN, initial cal. take max. of 200msec.
+ * Allow time to complete this calibration
+ */
+ msleep(200);
+
+ return 0;
+
+error:
+ zforce_command_wait(ts, COMMAND_DEACTIVATE);
+ return ret;
+}
+
+static int zforce_stop(struct zforce_ts *ts)
+{
+ struct i2c_client *client = ts->client;
+ int ret;
+
+ dev_dbg(&client->dev, "stopping device\n");
+
+ /* Deactivates touch sensing and puts the device into sleep. */
+ ret = zforce_command_wait(ts, COMMAND_DEACTIVATE);
+ if (ret != 0) {
+ dev_err(&client->dev, "could not deactivate device, %d\n",
+ ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int zforce_touch_event(struct zforce_ts *ts, u8 *payload)
+{
+ struct i2c_client *client = ts->client;
+ const struct zforce_ts_platdata *pdata = dev_get_platdata(&client->dev);
+ struct zforce_point point;
+ int count, i, num = 0;
+
+ count = payload[0];
+ if (count > ZFORCE_REPORT_POINTS) {
+ dev_warn(&client->dev, "to many coordinates %d, expected max %d\n",
+ count, ZFORCE_REPORT_POINTS);
+ count = ZFORCE_REPORT_POINTS;
+ }
+
+ for (i = 0; i < count; i++) {
+ point.coord_x =
+ payload[9 * i + 2] << 8 | payload[9 * i + 1];
+ point.coord_y =
+ payload[9 * i + 4] << 8 | payload[9 * i + 3];
+
+ if (point.coord_x > pdata->x_max ||
+ point.coord_y > pdata->y_max) {
+ dev_warn(&client->dev, "coordinates (%d,%d) invalid\n",
+ point.coord_x, point.coord_y);
+ point.coord_x = point.coord_y = 0;
+ }
+
+ point.state = payload[9 * i + 5] & 0x03;
+ point.id = (payload[9 * i + 5] & 0xfc) >> 2;
+
+ /* determine touch major, minor and orientation */
+ point.area_major = max(payload[9 * i + 6],
+ payload[9 * i + 7]);
+ point.area_minor = min(payload[9 * i + 6],
+ payload[9 * i + 7]);
+ point.orientation = payload[9 * i + 6] > payload[9 * i + 7];
+
+ point.pressure = payload[9 * i + 8];
+ point.prblty = payload[9 * i + 9];
+
+ dev_dbg(&client->dev,
+ "point %d/%d: state %d, id %d, pressure %d, prblty %d, x %d, y %d, amajor %d, aminor %d, ori %d\n",
+ i, count, point.state, point.id,
+ point.pressure, point.prblty,
+ point.coord_x, point.coord_y,
+ point.area_major, point.area_minor,
+ point.orientation);
+
+ /* the zforce id starts with "1", so needs to be decreased */
+ input_mt_slot(ts->input, point.id - 1);
+
+ input_mt_report_slot_state(ts->input, MT_TOOL_FINGER,
+ point.state != STATE_UP);
+
+ if (point.state != STATE_UP) {
+ input_report_abs(ts->input, ABS_MT_POSITION_X,
+ point.coord_x);
+ input_report_abs(ts->input, ABS_MT_POSITION_Y,
+ point.coord_y);
+ input_report_abs(ts->input, ABS_MT_TOUCH_MAJOR,
+ point.area_major);
+ input_report_abs(ts->input, ABS_MT_TOUCH_MINOR,
+ point.area_minor);
+ input_report_abs(ts->input, ABS_MT_ORIENTATION,
+ point.orientation);
+ num++;
+ }
+ }
+
+ input_mt_sync_frame(ts->input);
+
+ input_mt_report_finger_count(ts->input, num);
+
+ input_sync(ts->input);
+
+ return 0;
+}
+
+static int zforce_read_packet(struct zforce_ts *ts, u8 *buf)
+{
+ struct i2c_client *client = ts->client;
+ int ret;
+
+ mutex_lock(&ts->access_mutex);
+
+ /* read 2 byte message header */
+ ret = i2c_master_recv(client, buf, 2);
+ if (ret < 0) {
+ dev_err(&client->dev, "error reading header: %d\n", ret);
+ goto unlock;
+ }
+
+ if (buf[PAYLOAD_HEADER] != FRAME_START) {
+ dev_err(&client->dev, "invalid frame start: %d\n", buf[0]);
+ ret = -EIO;
+ goto unlock;
+ }
+
+ if (buf[PAYLOAD_LENGTH] <= 0 || buf[PAYLOAD_LENGTH] > 255) {
+ dev_err(&client->dev, "invalid payload length: %d\n",
+ buf[PAYLOAD_LENGTH]);
+ ret = -EIO;
+ goto unlock;
+ }
+
+ /* read the message */
+ ret = i2c_master_recv(client, &buf[PAYLOAD_BODY], buf[PAYLOAD_LENGTH]);
+ if (ret < 0) {
+ dev_err(&client->dev, "error reading payload: %d\n", ret);
+ goto unlock;
+ }
+
+ dev_dbg(&client->dev, "read %d bytes for response command 0x%x\n",
+ buf[PAYLOAD_LENGTH], buf[PAYLOAD_BODY]);
+
+unlock:
+ mutex_unlock(&ts->access_mutex);
+ return ret;
+}
+
+static void zforce_complete(struct zforce_ts *ts, int cmd, int result)
+{
+ struct i2c_client *client = ts->client;
+
+ if (ts->command_waiting == cmd) {
+ dev_dbg(&client->dev, "completing command 0x%x\n", cmd);
+ ts->command_result = result;
+ complete(&ts->command_done);
+ } else {
+ dev_dbg(&client->dev, "command %d not for us\n", cmd);
+ }
+}
+
+static irqreturn_t zforce_interrupt(int irq, void *dev_id)
+{
+ struct zforce_ts *ts = dev_id;
+ struct i2c_client *client = ts->client;
+ const struct zforce_ts_platdata *pdata = dev_get_platdata(&client->dev);
+ int ret;
+ u8 payload_buffer[512];
+ u8 *payload;
+
+ /*
+ * When suspended, emit a wakeup signal if necessary and return.
+ * Due to the level-interrupt we will get re-triggered later.
+ */
+ if (ts->suspended) {
+ if (device_may_wakeup(&client->dev))
+ pm_wakeup_event(&client->dev, 500);
+ msleep(20);
+ return IRQ_HANDLED;
+ }
+
+ dev_dbg(&client->dev, "handling interrupt\n");
+
+ /* Don't emit wakeup events from commands run by zforce_suspend */
+ if (!ts->suspending && device_may_wakeup(&client->dev))
+ pm_stay_awake(&client->dev);
+
+ while (!gpio_get_value(pdata->gpio_int)) {
+ ret = zforce_read_packet(ts, payload_buffer);
+ if (ret < 0) {
+ dev_err(&client->dev, "could not read packet, ret: %d\n",
+ ret);
+ break;
+ }
+
+ payload = &payload_buffer[PAYLOAD_BODY];
+
+ switch (payload[RESPONSE_ID]) {
+ case NOTIFICATION_TOUCH:
+ /*
+ * Always report touch-events received while
+ * suspending, when being a wakeup source
+ */
+ if (ts->suspending && device_may_wakeup(&client->dev))
+ pm_wakeup_event(&client->dev, 500);
+ zforce_touch_event(ts, &payload[RESPONSE_DATA]);
+ break;
+
+ case NOTIFICATION_BOOTCOMPLETE:
+ ts->boot_complete = payload[RESPONSE_DATA];
+ zforce_complete(ts, payload[RESPONSE_ID], 0);
+ break;
+
+ case RESPONSE_INITIALIZE:
+ case RESPONSE_DEACTIVATE:
+ case RESPONSE_SETCONFIG:
+ case RESPONSE_RESOLUTION:
+ case RESPONSE_SCANFREQ:
+ zforce_complete(ts, payload[RESPONSE_ID],
+ payload[RESPONSE_DATA]);
+ break;
+
+ case RESPONSE_STATUS:
+ /*
+ * Version Payload Results
+ * [2:major] [2:minor] [2:build] [2:rev]
+ */
+ ts->version_major = (payload[RESPONSE_DATA + 1] << 8) |
+ payload[RESPONSE_DATA];
+ ts->version_minor = (payload[RESPONSE_DATA + 3] << 8) |
+ payload[RESPONSE_DATA + 2];
+ ts->version_build = (payload[RESPONSE_DATA + 5] << 8) |
+ payload[RESPONSE_DATA + 4];
+ ts->version_rev = (payload[RESPONSE_DATA + 7] << 8) |
+ payload[RESPONSE_DATA + 6];
+ dev_dbg(&ts->client->dev, "Firmware Version %04x:%04x %04x:%04x\n",
+ ts->version_major, ts->version_minor,
+ ts->version_build, ts->version_rev);
+
+ zforce_complete(ts, payload[RESPONSE_ID], 0);
+ break;
+
+ case NOTIFICATION_INVALID_COMMAND:
+ dev_err(&ts->client->dev, "invalid command: 0x%x\n",
+ payload[RESPONSE_DATA]);
+ break;
+
+ default:
+ dev_err(&ts->client->dev, "unrecognized response id: 0x%x\n",
+ payload[RESPONSE_ID]);
+ break;
+ }
+ }
+
+ if (!ts->suspending && device_may_wakeup(&client->dev))
+ pm_relax(&client->dev);
+
+ dev_dbg(&client->dev, "finished interrupt\n");
+
+ return IRQ_HANDLED;
+}
+
+static int zforce_input_open(struct input_dev *dev)
+{
+ struct zforce_ts *ts = input_get_drvdata(dev);
+ int ret;
+
+ ret = zforce_start(ts);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void zforce_input_close(struct input_dev *dev)
+{
+ struct zforce_ts *ts = input_get_drvdata(dev);
+ struct i2c_client *client = ts->client;
+ int ret;
+
+ ret = zforce_stop(ts);
+ if (ret)
+ dev_warn(&client->dev, "stopping zforce failed\n");
+
+ return;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int zforce_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct zforce_ts *ts = i2c_get_clientdata(client);
+ struct input_dev *input = ts->input;
+ int ret = 0;
+
+ mutex_lock(&input->mutex);
+ ts->suspending = true;
+
+ /*
+ * When configured as a wakeup source device should always wake
+ * the system, therefore start device if necessary.
+ */
+ if (device_may_wakeup(&client->dev)) {
+ dev_dbg(&client->dev, "suspend while being a wakeup source\n");
+
+ /* Need to start device, if not open, to be a wakeup source. */
+ if (!input->users) {
+ ret = zforce_start(ts);
+ if (ret)
+ goto unlock;
+ }
+
+ enable_irq_wake(client->irq);
+ } else if (input->users) {
+ dev_dbg(&client->dev, "suspend without being a wakeup source\n");
+
+ ret = zforce_stop(ts);
+ if (ret)
+ goto unlock;
+
+ disable_irq(client->irq);
+ }
+
+ ts->suspended = true;
+
+unlock:
+ ts->suspending = false;
+ mutex_unlock(&input->mutex);
+
+ return ret;
+}
+
+static int zforce_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct zforce_ts *ts = i2c_get_clientdata(client);
+ struct input_dev *input = ts->input;
+ int ret = 0;
+
+ mutex_lock(&input->mutex);
+
+ ts->suspended = false;
+
+ if (device_may_wakeup(&client->dev)) {
+ dev_dbg(&client->dev, "resume from being a wakeup source\n");
+
+ disable_irq_wake(client->irq);
+
+ /* need to stop device if it was not open on suspend */
+ if (!input->users) {
+ ret = zforce_stop(ts);
+ if (ret)
+ goto unlock;
+ }
+ } else if (input->users) {
+ dev_dbg(&client->dev, "resume without being a wakeup source\n");
+
+ enable_irq(client->irq);
+
+ ret = zforce_start(ts);
+ if (ret < 0)
+ goto unlock;
+ }
+
+unlock:
+ mutex_unlock(&input->mutex);
+
+ return ret;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(zforce_pm_ops, zforce_suspend, zforce_resume);
+
+static void zforce_reset(void *data)
+{
+ struct zforce_ts *ts = data;
+
+ gpio_set_value(ts->pdata->gpio_rst, 0);
+}
+
+static int zforce_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ const struct zforce_ts_platdata *pdata = dev_get_platdata(&client->dev);
+ struct zforce_ts *ts;
+ struct input_dev *input_dev;
+ int ret;
+
+ if (!pdata)
+ return -EINVAL;
+
+ ts = devm_kzalloc(&client->dev, sizeof(struct zforce_ts), GFP_KERNEL);
+ if (!ts)
+ return -ENOMEM;
+
+ ret = devm_gpio_request_one(&client->dev, pdata->gpio_int, GPIOF_IN,
+ "zforce_ts_int");
+ if (ret) {
+ dev_err(&client->dev, "request of gpio %d failed, %d\n",
+ pdata->gpio_int, ret);
+ return ret;
+ }
+
+ ret = devm_gpio_request_one(&client->dev, pdata->gpio_rst,
+ GPIOF_OUT_INIT_LOW, "zforce_ts_rst");
+ if (ret) {
+ dev_err(&client->dev, "request of gpio %d failed, %d\n",
+ pdata->gpio_rst, ret);
+ return ret;
+ }
+
+ ret = devm_add_action(&client->dev, zforce_reset, ts);
+ if (ret) {
+ dev_err(&client->dev, "failed to register reset action, %d\n",
+ ret);
+ return ret;
+ }
+
+ snprintf(ts->phys, sizeof(ts->phys),
+ "%s/input0", dev_name(&client->dev));
+
+ input_dev = devm_input_allocate_device(&client->dev);
+ if (!input_dev) {
+ dev_err(&client->dev, "could not allocate input device\n");
+ return -ENOMEM;
+ }
+
+ mutex_init(&ts->access_mutex);
+ mutex_init(&ts->command_mutex);
+
+ ts->pdata = pdata;
+ ts->client = client;
+ ts->input = input_dev;
+
+ input_dev->name = "Neonode zForce touchscreen";
+ input_dev->phys = ts->phys;
+ input_dev->id.bustype = BUS_I2C;
+
+ input_dev->open = zforce_input_open;
+ input_dev->close = zforce_input_close;
+
+ __set_bit(EV_KEY, input_dev->evbit);
+ __set_bit(EV_SYN, input_dev->evbit);
+ __set_bit(EV_ABS, input_dev->evbit);
+
+ /* For multi touch */
+ input_set_abs_params(input_dev, ABS_MT_POSITION_X, 0,
+ pdata->x_max, 0, 0);
+ input_set_abs_params(input_dev, ABS_MT_POSITION_Y, 0,
+ pdata->y_max, 0, 0);
+
+ input_set_abs_params(input_dev, ABS_MT_TOUCH_MAJOR, 0,
+ ZFORCE_MAX_AREA, 0, 0);
+ input_set_abs_params(input_dev, ABS_MT_TOUCH_MINOR, 0,
+ ZFORCE_MAX_AREA, 0, 0);
+ input_set_abs_params(input_dev, ABS_MT_ORIENTATION, 0, 1, 0, 0);
+ input_mt_init_slots(input_dev, ZFORCE_REPORT_POINTS, INPUT_MT_DIRECT);
+
+ input_set_drvdata(ts->input, ts);
+
+ init_completion(&ts->command_done);
+
+ /*
+ * The zforce pulls the interrupt low when it has data ready.
+ * After it is triggered the isr thread runs until all the available
+ * packets have been read and the interrupt is high again.
+ * Therefore we can trigger the interrupt anytime it is low and do
+ * not need to limit it to the interrupt edge.
+ */
+ ret = devm_request_threaded_irq(&client->dev, client->irq, NULL,
+ zforce_interrupt,
+ IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ input_dev->name, ts);
+ if (ret) {
+ dev_err(&client->dev, "irq %d request failed\n", client->irq);
+ return ret;
+ }
+
+ i2c_set_clientdata(client, ts);
+
+ /* let the controller boot */
+ gpio_set_value(pdata->gpio_rst, 1);
+
+ ts->command_waiting = NOTIFICATION_BOOTCOMPLETE;
+ if (wait_for_completion_timeout(&ts->command_done, WAIT_TIMEOUT) == 0)
+ dev_warn(&client->dev, "bootcomplete timed out\n");
+
+ /* need to start device to get version information */
+ ret = zforce_command_wait(ts, COMMAND_INITIALIZE);
+ if (ret) {
+ dev_err(&client->dev, "unable to initialize, %d\n", ret);
+ return ret;
+ }
+
+ /* this gets the firmware version among other informations */
+ ret = zforce_command_wait(ts, COMMAND_STATUS);
+ if (ret < 0) {
+ dev_err(&client->dev, "couldn't get status, %d\n", ret);
+ zforce_stop(ts);
+ return ret;
+ }
+
+ /* stop device and put it into sleep until it is opened */
+ ret = zforce_stop(ts);
+ if (ret < 0)
+ return ret;
+
+ device_set_wakeup_capable(&client->dev, true);
+
+ ret = input_register_device(input_dev);
+ if (ret) {
+ dev_err(&client->dev, "could not register input device, %d\n",
+ ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct i2c_device_id zforce_idtable[] = {
+ { "zforce-ts", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, zforce_idtable);
+
+static struct i2c_driver zforce_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "zforce-ts",
+ .pm = &zforce_pm_ops,
+ },
+ .probe = zforce_probe,
+ .id_table = zforce_idtable,
+};
+
+module_i2c_driver(zforce_driver);
+
+MODULE_AUTHOR("Heiko Stuebner <heiko@sntech.de>");
+MODULE_DESCRIPTION("zForce TouchScreen Driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+/* drivers/input/touchscreen/zforce.c
+ *
+ * Copyright (C) 2012-2013 MundoReader S.L.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _LINUX_INPUT_ZFORCE_TS_H
+#define _LINUX_INPUT_ZFORCE_TS_H
+
+struct zforce_ts_platdata {
+ int gpio_int;
+ int gpio_rst;
+
+ unsigned int x_max;
+ unsigned int y_max;
+};
+
+#endif /* _LINUX_INPUT_ZFORCE_TS_H */
projects / cascardo / linux.git / commitdiff