tty: stop defining STD_COM_FLAGS in drivers

STD_COM_FLAGS is mostly a bad name for what the drivers thinks it is.
Stop using it and pass the flags directly.

cyclades defines it as 0, so we do not assign anything to freshly
tty_port_init'ed structure.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/arch/xtensa/platforms/xt2000/setup.c b/arch/xtensa/platforms/xt2000/setup.c
index 5f4bd71..4904c5c 100644 (file)
--- a/arch/xtensa/platforms/xt2000/setup.c
+++ b/arch/xtensa/platforms/xt2000/setup.c
@@ -113,7 +113,6 @@ void platform_heartbeat(void)
 }
 
 //#define RS_TABLE_SIZE 2
-//#define STD_COM_FLAGS (UPF_BOOT_AUTOCONF|UPF_SKIP_TEST)
 
 #define _SERIAL_PORT(_base,_irq)                                       \
 {                                                                      \

diff --git a/drivers/tty/cyclades.c b/drivers/tty/cyclades.c
index fcc4962..5e4fa92 100644 (file)
--- a/drivers/tty/cyclades.c
+++ b/drivers/tty/cyclades.c
@@ -93,8 +93,6 @@ static void cy_send_xchar(struct tty_struct *tty, char ch);
 #define        SERIAL_XMIT_SIZE        (min(PAGE_SIZE, 4096))
 #endif
 
-#define STD_COM_FLAGS (0)
-
 /* firmware stuff */
 #define ZL_MAX_BLOCKS  16
 #define DRIVER_VERSION 0x02010203
@@ -3083,7 +3081,6 @@ static int cy_init_card(struct cyclades_card *cinfo)
 
                info->port.closing_wait = CLOSING_WAIT_DELAY;
                info->port.close_delay = 5 * HZ / 10;
-               info->port.flags = STD_COM_FLAGS;
                init_completion(&info->shutdown_wait);
 
                if (cy_is_Z(cinfo)) {

diff --git a/drivers/tty/serial/m32r_sio.c b/drivers/tty/serial/m32r_sio.c
index 68765f7..1b01504 100644 (file)
--- a/drivers/tty/serial/m32r_sio.c
+++ b/drivers/tty/serial/m32r_sio.c
@@ -51,9 +51,6 @@
 
 #define PASS_LIMIT     256
 
-/* Standard COM flags */
-#define STD_COM_FLAGS (UPF_BOOT_AUTOCONF | UPF_SKIP_TEST)
-
 static const struct {
        unsigned int port;
        unsigned int irq;
@@ -892,7 +889,7 @@ static void __init m32r_sio_init_ports(void)
                up->port.iobase   = old_serial_port[i].port;
                up->port.irq      = irq_canonicalize(old_serial_port[i].irq);
                up->port.uartclk  = BAUD_RATE * 16;
-               up->port.flags    = STD_COM_FLAGS;
+               up->port.flags    = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST;
                up->port.membase  = 0;
                up->port.iotype   = 0;
                up->port.regshift = 0;