ARM/NOMADIK ARCHITECTURE
M: Alessandro Rubini <rubini@unipv.it>
M: Linus Walleij <linus.walleij@linaro.org>
-M: STEricsson <STEricsson_nomadik_linux@list.st.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-nomadik/
usbphy0: usbphy@0 {
compatible = "usb-nop-xceiv";
- clocks = <&clks 124>;
+ clocks = <&clks 75>;
clock-names = "main_clk";
status = "okay";
};
--- /dev/null
+CONFIG_IRQ_DOMAIN_DEBUG=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_ARCH_MULTI_V6=y
+CONFIG_ARCH_WM8750=y
+CONFIG_ARCH_WM8850=y
+CONFIG_ARM_ERRATA_720789=y
+CONFIG_ARM_ERRATA_754322=y
+CONFIG_ARM_ERRATA_775420=y
+CONFIG_HAVE_ARM_ARCH_TIMER=y
+CONFIG_AEABI=y
+CONFIG_HIGHMEM=y
+CONFIG_HIGHPTE=y
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_VFP=y
+CONFIG_NEON=y
+CONFIG_PM_RUNTIME=y
+CONFIG_NET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_PROC_DEVICETREE=y
+CONFIG_EEPROM_93CX6=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
+CONFIG_NETDEVICES=y
+# CONFIG_NET_CADENCE is not set
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+# CONFIG_NET_VENDOR_SMSC is not set
+# CONFIG_NET_VENDOR_STMICRO is not set
+CONFIG_VIA_VELOCITY=y
+# CONFIG_NET_VENDOR_WIZNET is not set
+CONFIG_PHYLIB=y
+CONFIG_INPUT_MATRIXKMAP=y
+CONFIG_SERIAL_VT8500=y
+CONFIG_SERIAL_VT8500_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_WMT=y
+CONFIG_PINCTRL_SINGLE=y
+CONFIG_PINCTRL_WM8750=y
+CONFIG_GPIO_GENERIC_PLATFORM=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_RESET=y
+CONFIG_MFD_SYSCON=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+CONFIG_REGULATOR_GPIO=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_UHCI_HCD=y
+CONFIG_USB_STORAGE=y
+CONFIG_NOP_USB_XCEIV=y
+CONFIG_USB_GPIO_VBUS=y
+CONFIG_USB_ULPI=y
+CONFIG_MMC=y
+CONFIG_MMC_DEBUG=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_VT8500=y
+CONFIG_DMADEVICES=y
+CONFIG_COMMON_CLK_DEBUG=y
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_PWM=y
+CONFIG_PWM_VT8500=y
+CONFIG_RESET_CONTROLLER=y
+CONFIG_GENERIC_PHY=y
+CONFIG_EXT4_FS=y
+CONFIG_TMPFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_LOCKUP_DETECTOR=y
# Makefile for the linux kernel.
#
-obj-y := irq.o gpio.o setup.o
+obj-y := irq.o gpio.o setup.o sysirq_mask.o
obj-m :=
obj-n :=
obj- :=
arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9_alt_restart;
+ at91_sysirq_mask_rtt(AT91SAM9260_BASE_RTT);
+
/* Register GPIO subsystem */
at91_gpio_init(at91sam9260_gpio, 3);
}
arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9_alt_restart;
+ at91_sysirq_mask_rtt(AT91SAM9261_BASE_RTT);
+
/* Register GPIO subsystem */
at91_gpio_init(at91sam9261_gpio, 3);
}
arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9_alt_restart;
+ at91_sysirq_mask_rtt(AT91SAM9263_BASE_RTT0);
+ at91_sysirq_mask_rtt(AT91SAM9263_BASE_RTT1);
+
/* Register GPIO subsystem */
at91_gpio_init(at91sam9263_gpio, 5);
}
arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9g45_restart;
+ at91_sysirq_mask_rtc(AT91SAM9G45_BASE_RTC);
+ at91_sysirq_mask_rtt(AT91SAM9G45_BASE_RTT);
+
/* Register GPIO subsystem */
at91_gpio_init(at91sam9g45_gpio, 5);
}
at91_init_sram(0, AT91SAM9N12_SRAM_BASE, AT91SAM9N12_SRAM_SIZE);
}
+static void __init at91sam9n12_initialize(void)
+{
+ at91_sysirq_mask_rtc(AT91SAM9N12_BASE_RTC);
+}
+
AT91_SOC_START(at91sam9n12)
.map_io = at91sam9n12_map_io,
.register_clocks = at91sam9n12_register_clocks,
+ .init = at91sam9n12_initialize,
AT91_SOC_END
arm_pm_idle = at91sam9_idle;
arm_pm_restart = at91sam9_alt_restart;
+ at91_sysirq_mask_rtc(AT91SAM9RL_BASE_RTC);
+ at91_sysirq_mask_rtt(AT91SAM9RL_BASE_RTT);
+
/* Register GPIO subsystem */
at91_gpio_init(at91sam9rl_gpio, 4);
}
at91_init_sram(0, AT91SAM9X5_SRAM_BASE, AT91SAM9X5_SRAM_SIZE);
}
+static void __init at91sam9x5_initialize(void)
+{
+ at91_sysirq_mask_rtc(AT91SAM9X5_BASE_RTC);
+}
+
/* --------------------------------------------------------------------
* Interrupt initialization
* -------------------------------------------------------------------- */
AT91_SOC_START(at91sam9x5)
.map_io = at91sam9x5_map_io,
.register_clocks = at91sam9x5_register_clocks,
+ .init = at91sam9x5_initialize,
AT91_SOC_END
struct device_node *parent);
extern int __init at91_aic5_of_init(struct device_node *node,
struct device_node *parent);
+extern void __init at91_sysirq_mask_rtc(u32 rtc_base);
+extern void __init at91_sysirq_mask_rtt(u32 rtt_base);
/* Timer */
#define AT91SAM9N12_BASE_USART2 0xf8024000
#define AT91SAM9N12_BASE_USART3 0xf8028000
+/*
+ * System Peripherals
+ */
+#define AT91SAM9N12_BASE_RTC 0xfffffeb0
+
/*
* Internal Memory.
*/
#define AT91SAM9X5_BASE_USART1 0xf8020000
#define AT91SAM9X5_BASE_USART2 0xf8024000
+/*
+ * System Peripherals
+ */
+#define AT91SAM9X5_BASE_RTC 0xfffffeb0
+
/*
* Internal Memory.
*/
#define SAMA5D3_BASE_USART2 0xf8020000
#define SAMA5D3_BASE_USART3 0xf8024000
+/*
+ * System Peripherals
+ */
+#define SAMA5D3_BASE_RTC 0xfffffeb0
+
/*
* Internal Memory
*/
at91_init_sram(0, SAMA5D3_SRAM_BASE, SAMA5D3_SRAM_SIZE);
}
+static void __init sama5d3_initialize(void)
+{
+ at91_sysirq_mask_rtc(SAMA5D3_BASE_RTC);
+}
+
AT91_SOC_START(sama5d3)
.map_io = sama5d3_map_io,
.register_clocks = sama5d3_register_clocks,
+ .init = sama5d3_initialize,
AT91_SOC_END
--- /dev/null
+/*
+ * sysirq_mask.c - System-interrupt masking
+ *
+ * Copyright (C) 2013 Johan Hovold <jhovold@gmail.com>
+ *
+ * Functions to disable system interrupts from backup-powered peripherals.
+ *
+ * The RTC and RTT-peripherals are generally powered by backup power (VDDBU)
+ * and are not reset on wake-up, user, watchdog or software reset. This means
+ * that their interrupts may be enabled during early boot (e.g. after a user
+ * reset).
+ *
+ * As the RTC and RTT share the system-interrupt line with the PIT, an
+ * interrupt occurring before a handler has been installed would lead to the
+ * system interrupt being disabled and prevent the system from booting.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/io.h>
+#include <mach/at91_rtt.h>
+
+#include "generic.h"
+
+#define AT91_RTC_IDR 0x24 /* Interrupt Disable Register */
+#define AT91_RTC_IMR 0x28 /* Interrupt Mask Register */
+
+void __init at91_sysirq_mask_rtc(u32 rtc_base)
+{
+ void __iomem *base;
+ u32 mask;
+
+ base = ioremap(rtc_base, 64);
+ if (!base)
+ return;
+
+ mask = readl_relaxed(base + AT91_RTC_IMR);
+ if (mask) {
+ pr_info("AT91: Disabling rtc irq\n");
+ writel_relaxed(mask, base + AT91_RTC_IDR);
+ (void)readl_relaxed(base + AT91_RTC_IMR); /* flush */
+ }
+
+ iounmap(base);
+}
+
+void __init at91_sysirq_mask_rtt(u32 rtt_base)
+{
+ void __iomem *base;
+ void __iomem *reg;
+ u32 mode;
+
+ base = ioremap(rtt_base, 16);
+ if (!base)
+ return;
+
+ reg = base + AT91_RTT_MR;
+
+ mode = readl_relaxed(reg);
+ if (mode & (AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN)) {
+ pr_info("AT91: Disabling rtt irq\n");
+ mode &= ~(AT91_RTT_ALMIEN | AT91_RTT_RTTINCIEN);
+ writel_relaxed(mode, reg);
+ (void)readl_relaxed(reg); /* flush */
+ }
+
+ iounmap(base);
+}
select ARCH_HAS_OPP
select ARCH_WANT_OPTIONAL_GPIOLIB
select ARM_AMBA
- select ARM_ERRATA_764369
+ select ARM_ERRATA_764369 if SMP
select ARM_ERRATA_775420
select ARM_ERRATA_798181
select ARM_GIC
ifeq ($(CONFIG_PM),y)
obj-$(CONFIG_SOC_IMX6Q) += pm-imx6q.o headsmp.o
-# i.MX6SL reuses pm-imx6q.c
-obj-$(CONFIG_SOC_IMX6SL) += pm-imx6q.o
+# i.MX6SL reuses i.MX6Q code
+obj-$(CONFIG_SOC_IMX6SL) += pm-imx6q.o headsmp.o
endif
# i.MX5 based machines
{ .val = 1, .div = 10, },
{ .val = 2, .div = 5, },
{ .val = 3, .div = 4, },
+ { /* sentinel */ }
};
static struct clk_div_table post_div_table[] = {
{ .val = 2, .div = 1, },
{ .val = 1, .div = 2, },
{ .val = 0, .div = 4, },
- { }
+ { /* sentinel */ }
};
static struct clk_div_table video_div_table[] = {
{ .val = 1, .div = 2, },
{ .val = 2, .div = 1, },
{ .val = 3, .div = 4, },
- { }
+ { /* sentinel */ }
};
static void __init imx6q_clocks_init(struct device_node *ccm_node)
clk[asrc_podf] = imx_clk_divider("asrc_podf", "asrc_pred", base + 0x30, 9, 3);
clk[spdif_pred] = imx_clk_divider("spdif_pred", "spdif_sel", base + 0x30, 25, 3);
clk[spdif_podf] = imx_clk_divider("spdif_podf", "spdif_pred", base + 0x30, 22, 3);
- clk[can_root] = imx_clk_divider("can_root", "pll3_usb_otg", base + 0x20, 2, 6);
+ clk[can_root] = imx_clk_divider("can_root", "pll3_60m", base + 0x20, 2, 6);
clk[ecspi_root] = imx_clk_divider("ecspi_root", "pll3_60m", base + 0x38, 19, 6);
clk[gpu2d_core_podf] = imx_clk_divider("gpu2d_core_podf", "gpu2d_core_sel", base + 0x18, 23, 3);
clk[gpu3d_core_podf] = imx_clk_divider("gpu3d_core_podf", "gpu3d_core_sel", base + 0x18, 26, 3);
#include <linux/clk.h>
#include <linux/clk-provider.h>
+#include <linux/delay.h>
#include <linux/io.h>
#include <linux/slab.h>
#include <linux/jiffies.h>
#define to_clk_pllv3(_hw) container_of(_hw, struct clk_pllv3, hw)
+static int clk_pllv3_wait_lock(struct clk_pllv3 *pll)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(10);
+ u32 val = readl_relaxed(pll->base) & BM_PLL_POWER;
+
+ /* No need to wait for lock when pll is not powered up */
+ if ((pll->powerup_set && !val) || (!pll->powerup_set && val))
+ return 0;
+
+ /* Wait for PLL to lock */
+ do {
+ if (readl_relaxed(pll->base) & BM_PLL_LOCK)
+ break;
+ if (time_after(jiffies, timeout))
+ break;
+ usleep_range(50, 500);
+ } while (1);
+
+ return readl_relaxed(pll->base) & BM_PLL_LOCK ? 0 : -ETIMEDOUT;
+}
+
static int clk_pllv3_prepare(struct clk_hw *hw)
{
struct clk_pllv3 *pll = to_clk_pllv3(hw);
- unsigned long timeout;
u32 val;
+ int ret;
val = readl_relaxed(pll->base);
- val &= ~BM_PLL_BYPASS;
if (pll->powerup_set)
val |= BM_PLL_POWER;
else
val &= ~BM_PLL_POWER;
writel_relaxed(val, pll->base);
- timeout = jiffies + msecs_to_jiffies(10);
- /* Wait for PLL to lock */
- do {
- if (readl_relaxed(pll->base) & BM_PLL_LOCK)
- break;
- if (time_after(jiffies, timeout))
- break;
- } while (1);
+ ret = clk_pllv3_wait_lock(pll);
+ if (ret)
+ return ret;
- if (readl_relaxed(pll->base) & BM_PLL_LOCK)
- return 0;
- else
- return -ETIMEDOUT;
+ val = readl_relaxed(pll->base);
+ val &= ~BM_PLL_BYPASS;
+ writel_relaxed(val, pll->base);
+
+ return 0;
}
static void clk_pllv3_unprepare(struct clk_hw *hw)
val |= div;
writel_relaxed(val, pll->base);
- return 0;
+ return clk_pllv3_wait_lock(pll);
}
static const struct clk_ops clk_pllv3_ops = {
val |= div;
writel_relaxed(val, pll->base);
- return 0;
+ return clk_pllv3_wait_lock(pll);
}
static const struct clk_ops clk_pllv3_sys_ops = {
writel_relaxed(mfn, pll->base + PLL_NUM_OFFSET);
writel_relaxed(mfd, pll->base + PLL_DENOM_OFFSET);
- return 0;
+ return clk_pllv3_wait_lock(pll);
}
static const struct clk_ops clk_pllv3_av_ops = {
static inline void imx_scu_standby_enable(void) {}
#endif
void imx_src_init(void);
-#ifdef CONFIG_HAVE_IMX_SRC
-void imx_src_prepare_restart(void);
-#else
-static inline void imx_src_prepare_restart(void) {}
-#endif
void imx_gpc_init(void);
void imx_gpc_pre_suspend(void);
void imx_gpc_post_resume(void);
writel_relaxed(arg, src_base + SRC_GPR1 + cpu * 8 + 4);
}
-void imx_src_prepare_restart(void)
-{
- u32 val;
-
- /* clear enable bits of secondary cores */
- spin_lock(&scr_lock);
- val = readl_relaxed(src_base + SRC_SCR);
- val &= ~(0x7 << BP_SRC_SCR_CORE1_ENABLE);
- writel_relaxed(val, src_base + SRC_SCR);
- spin_unlock(&scr_lock);
-
- /* clear persistent entry register of primary core */
- writel_relaxed(0, src_base + SRC_GPR1);
-}
-
void __init imx_src_init(void)
{
struct device_node *np;
{
unsigned int wcr_enable;
- if (cpu_is_imx6q() || cpu_is_imx6dl())
- imx_src_prepare_restart();
-
if (wdog_clk)
clk_enable(wdog_clk);
/* Assert SRS signal */
__raw_writew(wcr_enable, wdog_base);
- /* write twice to ensure the request will not get ignored */
+ /*
+ * Due to imx6q errata ERR004346 (WDOG: WDOG SRS bit requires to be
+ * written twice), we add another two writes to ensure there must be at
+ * least two writes happen in the same one 32kHz clock period. We save
+ * the target check here, since the writes shouldn't be a huge burden
+ * for other platforms.
+ */
+ __raw_writew(wcr_enable, wdog_base);
__raw_writew(wcr_enable, wdog_base);
/* wait for reset to assert... */
static void cp_clcd_enable(struct clcd_fb *fb)
{
struct fb_var_screeninfo *var = &fb->fb.var;
- u32 val = CM_CTRL_STATIC1 | CM_CTRL_STATIC2;
+ u32 val = CM_CTRL_STATIC1 | CM_CTRL_STATIC2
+ | CM_CTRL_LCDEN0 | CM_CTRL_LCDEN1;
if (var->bits_per_pixel <= 8 ||
(var->bits_per_pixel == 16 && var->green.length == 5))
select HAVE_ARM_SCU if SMP
select ARCH_REQUIRE_GPIOLIB
select ARM_ERRATA_754322
- select ARM_ERRATA_764369
+ select ARM_ERRATA_764369 if SMP
select ARM_ERRATA_775420
select PL310_ERRATA_753970 if CACHE_PL310
select PL310_ERRATA_769419 if CACHE_PL310
static void __init tegra_init_early(void)
{
- tegra_cpu_reset_handler_init();
tegra_apb_io_init();
tegra_init_fuse();
+ tegra_cpu_reset_handler_init();
tegra_init_cache();
tegra_powergate_init();
tegra_hotplug_init();
static int exynos_mipi_dsi_blank_mode(struct mipi_dsim_device *dsim, int power)
{
- struct platform_device *pdev = to_platform_device(dsim->dev);
struct mipi_dsim_lcd_driver *client_drv = dsim->dsim_lcd_drv;
struct mipi_dsim_lcd_device *client_dev = dsim->dsim_lcd_dev;
projects / cascardo / linux.git / commitdiff