--- /dev/null
+* MELFAS MIP4 Touchscreen
+
+Required properties:
+- compatible: must be "melfas,mip4_ts"
+- reg: I2C slave address of the chip (0x48 or 0x34)
+- interrupt-parent: interrupt controller to which the chip is connected
+- interrupts: interrupt to which the chip is connected
+
+Optional properties:
+- ce-gpios: GPIO connected to the CE (chip enable) pin of the chip
+
+Example:
+ i2c@00000000 {
+ touchscreen: melfas_mip4@48 {
+ compatible = "melfas,mip4_ts";
+ reg = <0x48>;
+ interrupt-parent = <&gpio>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+ ce-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
meas Measurement Specialties
mediatek MediaTek Inc.
melexis Melexis N.V.
+melfas MELFAS Inc.
merrii Merrii Technology Co., Ltd.
micrel Micrel Inc.
microchip Microchip Technology Inc.
otherwise byte 0 bit 4 must be set and byte 0/4/5 are
in NEW fmt
F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ...
+
+
+ALPS Absolute Mode - Protocol Version 8
+---------------------------------------
+
+Spoken by SS4 (73 03 14) and SS5 (73 03 28) hardware.
+
+The packet type is given by the APD field, bits 4-5 of byte 3.
+
+Touchpad packet (APD = 0x2):
+
+ b7 b6 b5 b4 b3 b2 b1 b0
+ byte 0: SWM SWR SWL 1 1 0 0 X7
+ byte 1: 0 X6 X5 X4 X3 X2 X1 X0
+ byte 2: 0 Y6 Y5 Y4 Y3 Y2 Y1 Y0
+ byte 3: 0 T&P 1 0 1 0 0 Y7
+ byte 4: 0 Z6 Z5 Z4 Z3 Z2 Z1 Z0
+ byte 5: 0 0 0 0 0 0 0 0
+
+SWM, SWR, SWL: Middle, Right, and Left button states
+
+Touchpad 1 Finger packet (APD = 0x0):
+
+ b7 b6 b5 b4 b3 b2 b1 b0
+ byte 0: SWM SWR SWL 1 1 X2 X1 X0
+ byte 1: X9 X8 X7 1 X6 X5 X4 X3
+ byte 2: 0 X11 X10 LFB Y3 Y2 Y1 Y0
+ byte 3: Y5 Y4 0 0 1 TAPF2 TAPF1 TAPF0
+ byte 4: Zv7 Y11 Y10 1 Y9 Y8 Y7 Y6
+ byte 5: Zv6 Zv5 Zv4 0 Zv3 Zv2 Zv1 Zv0
+
+TAPF: ???
+LFB: ???
+
+Touchpad 2 Finger packet (APD = 0x1):
+
+ b7 b6 b5 b4 b3 b2 b1 b0
+ byte 0: SWM SWR SWL 1 1 AX6 AX5 AX4
+ byte 1: AX11 AX10 AX9 AX8 AX7 AZ1 AY4 AZ0
+ byte 2: AY11 AY10 AY9 CONT AY8 AY7 AY6 AY5
+ byte 3: 0 0 0 1 1 BX6 BX5 BX4
+ byte 4: BX11 BX10 BX9 BX8 BX7 BZ1 BY4 BZ0
+ byte 5: BY11 BY10 BY9 0 BY8 BY7 BY5 BY5
+
+CONT: A 3-or-4 Finger packet is to follow
+
+Touchpad 3-or-4 Finger packet (APD = 0x3):
+
+ b7 b6 b5 b4 b3 b2 b1 b0
+ byte 0: SWM SWR SWL 1 1 AX6 AX5 AX4
+ byte 1: AX11 AX10 AX9 AX8 AX7 AZ1 AY4 AZ0
+ byte 2: AY11 AY10 AY9 OVF AY8 AY7 AY6 AY5
+ byte 3: 0 0 1 1 1 BX6 BX5 BX4
+ byte 4: BX11 BX10 BX9 BX8 BX7 BZ1 BY4 BZ0
+ byte 5: BY11 BY10 BY9 0 BY8 BY7 BY5 BY5
+
+OVF: 5th finger detected
i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
controllers
i8042.notimeout [HW] Ignore timeout condition signalled by controller
- i8042.reset [HW] Reset the controller during init and cleanup
+ i8042.reset [HW] Reset the controller during init, cleanup and
+ suspend-to-ram transitions, only during s2r
+ transitions, or never reset
+ Format: { 1 | Y | y | 0 | N | n }
+ 1, Y, y: always reset controller
+ 0, N, n: don't ever reset controller
+ Default: only on s2r transitions on x86; most other
+ architectures force reset to be always executed
i8042.unlock [HW] Unlock (ignore) the keylock
i8042.kbdreset [HW] Reset device connected to KBD port
F: drivers/scsi/megaraid.*
F: drivers/scsi/megaraid/
+MELFAS MIP4 TOUCHSCREEN DRIVER
+M: Sangwon Jee <jeesw@melfas.com>
+W: http://www.melfas.com
+S: Supported
+F: drivers/input/touchscreen/melfas_mip4.c
+F: Documentation/devicetree/bindings/input/touchscreen/melfas_mip4.txt
+
MELLANOX ETHERNET DRIVER (mlx4_en)
M: Tariq Toukan <tariqt@mellanox.com>
L: netdev@vger.kernel.org
6-byte ALPS packet */
#define ALPS_STICK_BITS 0x100 /* separate stick button bits */
#define ALPS_BUTTONPAD 0x200 /* device is a clickpad */
+#define ALPS_DUALPOINT_WITH_PRESSURE 0x400 /* device can report trackpoint pressure */
static const struct alps_model_info alps_model_data[] = {
{ { 0x32, 0x02, 0x14 }, 0x00, { ALPS_PROTO_V2, 0xf8, 0xf8, ALPS_PASS | ALPS_DUALPOINT } }, /* Toshiba Salellite Pro M10 */
{
unsigned char pkt_id = SS4_PACKET_ID_IDLE;
- if (byte[0] == 0x18 && byte[1] == 0x10 && byte[2] == 0x00 &&
- (byte[3] & 0x88) == 0x08 && byte[4] == 0x10 && byte[5] == 0x00) {
- pkt_id = SS4_PACKET_ID_IDLE;
- } else if (!(byte[3] & 0x10)) {
- pkt_id = SS4_PACKET_ID_ONE;
- } else if (!(byte[3] & 0x20)) {
+ switch (byte[3] & 0x30) {
+ case 0x00:
+ if (byte[0] == 0x18 && byte[1] == 0x10 && byte[2] == 0x00 &&
+ (byte[3] & 0x88) == 0x08 && byte[4] == 0x10 &&
+ byte[5] == 0x00) {
+ pkt_id = SS4_PACKET_ID_IDLE;
+ } else {
+ pkt_id = SS4_PACKET_ID_ONE;
+ }
+ break;
+ case 0x10:
+ /* two-finger finger positions */
pkt_id = SS4_PACKET_ID_TWO;
- } else {
+ break;
+ case 0x20:
+ /* stick pointer */
+ pkt_id = SS4_PACKET_ID_STICK;
+ break;
+ case 0x30:
+ /* third and fourth finger positions */
pkt_id = SS4_PACKET_ID_MULTI;
+ break;
}
return pkt_id;
f->mt[0].x = SS4_1F_X_V2(p);
f->mt[0].y = SS4_1F_Y_V2(p);
f->pressure = ((SS4_1F_Z_V2(p)) * 2) & 0x7f;
- f->fingers = 1;
+ /*
+ * When a button is held the device will give us events
+ * with x, y, and pressure of 0. This causes annoying jumps
+ * if a touch is released while the button is held.
+ * Handle this by claiming zero contacts.
+ */
+ f->fingers = f->pressure > 0 ? 1 : 0;
f->first_mp = 0;
f->is_mp = 0;
break;
}
break;
+ case SS4_PACKET_ID_STICK:
+ if (!(priv->flags & ALPS_DUALPOINT)) {
+ psmouse_warn(psmouse,
+ "Rejected trackstick packet from non DualPoint device");
+ } else {
+ int x = (s8)(((p[0] & 1) << 7) | (p[1] & 0x7f));
+ int y = (s8)(((p[3] & 1) << 7) | (p[2] & 0x7f));
+ int pressure = (s8)(p[4] & 0x7f);
+
+ input_report_rel(priv->dev2, REL_X, x);
+ input_report_rel(priv->dev2, REL_Y, -y);
+ input_report_abs(priv->dev2, ABS_PRESSURE, pressure);
+ }
+ break;
+
case SS4_PACKET_ID_IDLE:
default:
memset(f, 0, sizeof(struct alps_fields));
break;
}
- f->left = !!(SS4_BTN_V2(p) & 0x01);
- if (!(priv->flags & ALPS_BUTTONPAD)) {
- f->right = !!(SS4_BTN_V2(p) & 0x02);
- f->middle = !!(SS4_BTN_V2(p) & 0x04);
+ /* handle buttons */
+ if (pkt_id == SS4_PACKET_ID_STICK) {
+ f->ts_left = !!(SS4_BTN_V2(p) & 0x01);
+ if (!(priv->flags & ALPS_BUTTONPAD)) {
+ f->ts_right = !!(SS4_BTN_V2(p) & 0x02);
+ f->ts_middle = !!(SS4_BTN_V2(p) & 0x04);
+ }
+ } else {
+ f->left = !!(SS4_BTN_V2(p) & 0x01);
+ if (!(priv->flags & ALPS_BUTTONPAD)) {
+ f->right = !!(SS4_BTN_V2(p) & 0x02);
+ f->middle = !!(SS4_BTN_V2(p) & 0x04);
+ }
}
return 0;
struct alps_data *priv = psmouse->private;
unsigned char *packet = psmouse->packet;
struct input_dev *dev = psmouse->dev;
+ struct input_dev *dev2 = priv->dev2;
struct alps_fields *f = &priv->f;
memset(f, 0, sizeof(struct alps_fields));
input_report_abs(dev, ABS_PRESSURE, f->pressure);
input_sync(dev);
+
+ if (priv->flags & ALPS_DUALPOINT) {
+ input_report_key(dev2, BTN_LEFT, f->ts_left);
+ input_report_key(dev2, BTN_RIGHT, f->ts_right);
+ input_report_key(dev2, BTN_MIDDLE, f->ts_middle);
+ input_sync(dev2);
+ }
}
static bool alps_is_valid_package_ss4_v2(struct psmouse *psmouse)
if (alps_set_defaults_ss4_v2(psmouse, priv))
return -EIO;
+ if (priv->fw_ver[1] == 0x1)
+ priv->flags |= ALPS_DUALPOINT |
+ ALPS_DUALPOINT_WITH_PRESSURE;
+
break;
}
} else if (e7[0] == 0x73 && e7[1] == 0x03 &&
e7[2] == 0x14 && ec[1] == 0x02) {
protocol = &alps_v8_protocol_data;
+ } else if (e7[0] == 0x73 && e7[1] == 0x03 &&
+ e7[2] == 0x28 && ec[1] == 0x01) {
+ protocol = &alps_v8_protocol_data;
} else {
psmouse_dbg(psmouse,
"Likely not an ALPS touchpad: E7=%3ph, EC=%3ph\n", e7, ec);
input_set_capability(dev2, EV_REL, REL_X);
input_set_capability(dev2, EV_REL, REL_Y);
+ if (priv->flags & ALPS_DUALPOINT_WITH_PRESSURE) {
+ input_set_capability(dev2, EV_ABS, ABS_PRESSURE);
+ input_set_abs_params(dev2, ABS_PRESSURE, 0, 127, 0, 0);
+ }
input_set_capability(dev2, EV_KEY, BTN_LEFT);
input_set_capability(dev2, EV_KEY, BTN_RIGHT);
input_set_capability(dev2, EV_KEY, BTN_MIDDLE);
* or there's button activities.
* SS4_PACKET_ID_TWO: There's two or more fingers on touchpad
* SS4_PACKET_ID_MULTI: There's three or more fingers on touchpad
+ * SS4_PACKET_ID_STICK: A stick pointer packet
*/
enum SS4_PACKET_ID {
SS4_PACKET_ID_IDLE = 0,
SS4_PACKET_ID_ONE,
SS4_PACKET_ID_TWO,
SS4_PACKET_ID_MULTI,
+ SS4_PACKET_ID_STICK,
};
#define SS4_COUNT_PER_ELECTRODE 256
* System76 Pangolin 0x250f01 ? 2 hw buttons
* (*) + 3 trackpoint buttons
* (**) + 0 trackpoint buttons
- * Note: Lenovo L430 and Lenovo L430 have the same fw_version/caps
+ * Note: Lenovo L430 and Lenovo L530 have the same fw_version/caps
*/
static void elantech_set_buttonpad_prop(struct psmouse *psmouse)
{
DMI_MATCH(DMI_PRODUCT_NAME, "CELSIUS H730"),
},
},
+ {
+ /* Fujitsu H760 also has a middle button */
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "CELSIUS H760"),
+ },
+ },
#endif
{ }
};
},
},
{
- /* Fujitsu LIFEBOOK E554 does not work with crc_enabled == 0 */
+ /* Fujitsu H760 does not work with crc_enabled == 0 */
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
- DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E554"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "CELSIUS H760"),
},
},
{
DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E544"),
},
},
+ {
+ /* Fujitsu LIFEBOOK E554 does not work with crc_enabled == 0 */
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E554"),
+ },
+ },
+ {
+ /* Fujitsu LIFEBOOK E556 does not work with crc_enabled == 0 */
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK E556"),
+ },
+ },
{
/* Fujitsu LIFEBOOK U745 does not work with crc_enabled == 0 */
.matches = {
MODULE_DEVICE_TABLE(of, rmi_i2c_of_match);
#endif
+static void rmi_i2c_regulator_bulk_disable(void *data)
+{
+ struct rmi_i2c_xport *rmi_i2c = data;
+
+ regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
+ rmi_i2c->supplies);
+}
+
+static void rmi_i2c_unregister_transport(void *data)
+{
+ struct rmi_i2c_xport *rmi_i2c = data;
+
+ rmi_unregister_transport_device(&rmi_i2c->xport);
+}
+
static int rmi_i2c_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
if (retval < 0)
return retval;
+ retval = devm_add_action_or_reset(&client->dev,
+ rmi_i2c_regulator_bulk_disable,
+ rmi_i2c);
+ if (retval)
+ return retval;
+
of_property_read_u32(client->dev.of_node, "syna,startup-delay-ms",
&rmi_i2c->startup_delay);
client->addr);
return retval;
}
+ retval = devm_add_action_or_reset(&client->dev,
+ rmi_i2c_unregister_transport,
+ rmi_i2c);
+ if (retval)
+ return retval;
retval = rmi_i2c_init_irq(client);
if (retval < 0)
return 0;
}
-static int rmi_i2c_remove(struct i2c_client *client)
-{
- struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
-
- rmi_unregister_transport_device(&rmi_i2c->xport);
- regulator_bulk_disable(ARRAY_SIZE(rmi_i2c->supplies),
- rmi_i2c->supplies);
-
- return 0;
-}
-
#ifdef CONFIG_PM_SLEEP
static int rmi_i2c_suspend(struct device *dev)
{
},
.id_table = rmi_id,
.probe = rmi_i2c_probe,
- .remove = rmi_i2c_remove,
};
module_i2c_driver(rmi_i2c_driver);
}
#endif
+static void rmi_spi_unregister_transport(void *data)
+{
+ struct rmi_spi_xport *rmi_spi = data;
+
+ rmi_unregister_transport_device(&rmi_spi->xport);
+}
+
static int rmi_spi_probe(struct spi_device *spi)
{
struct rmi_spi_xport *rmi_spi;
dev_err(&spi->dev, "failed to register transport.\n");
return retval;
}
+ retval = devm_add_action_or_reset(&spi->dev,
+ rmi_spi_unregister_transport,
+ rmi_spi);
+ if (retval)
+ return retval;
retval = rmi_spi_init_irq(spi);
if (retval < 0)
return 0;
}
-static int rmi_spi_remove(struct spi_device *spi)
-{
- struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
-
- rmi_unregister_transport_device(&rmi_spi->xport);
-
- return 0;
-}
-
#ifdef CONFIG_PM_SLEEP
static int rmi_spi_suspend(struct device *dev)
{
},
.id_table = rmi_id,
.probe = rmi_spi_probe,
- .remove = rmi_spi_remove,
};
module_spi_driver(rmi_spi_driver);
return -EBUSY;
#endif
- i8042_reset = 1;
+ i8042_reset = I8042_RESET_ALWAYS;
return 0;
}
return -EBUSY;
#endif
- i8042_reset = 1;
+ i8042_reset = I8042_RESET_ALWAYS;
return 0;
}
static inline int i8042_platform_init(void)
{
- i8042_reset = 1;
+ i8042_reset = I8042_RESET_ALWAYS;
return 0;
}
}
}
- i8042_reset = 1;
+ i8042_reset = I8042_RESET_ALWAYS;
return 0;
}
if (!request_mem_region(I8042_REGION_START, I8042_REGION_SIZE, "i8042"))
return -EBUSY;
- i8042_reset = 1;
+ i8042_reset = I8042_RESET_ALWAYS;
return 0;
}
{ }
};
+/*
+ * On some Asus laptops, just running self tests cause problems.
+ */
+static const struct dmi_system_id i8042_dmi_noselftest_table[] = {
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "A455LD"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "K401LB"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "K501LB"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "K501LX"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "R409L"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "V502LX"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "X302LA"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "X450LCP"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "X450LD"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "X455LAB"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "X455LDB"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "X455LF"),
+ },
+ },
+ {
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+ DMI_MATCH(DMI_PRODUCT_NAME, "Z450LA"),
+ },
+ },
+ { }
+};
static const struct dmi_system_id __initconst i8042_dmi_reset_table[] = {
{
/* MSI Wind U-100 */
return retval;
#if defined(__ia64__)
- i8042_reset = true;
+ i8042_reset = I8042_RESET_ALWAYS;
#endif
#ifdef CONFIG_X86
- if (dmi_check_system(i8042_dmi_reset_table))
- i8042_reset = true;
+ /* Honor module parameter when value is not default */
+ if (i8042_reset == I8042_RESET_DEFAULT) {
+ if (dmi_check_system(i8042_dmi_reset_table))
+ i8042_reset = I8042_RESET_ALWAYS;
+
+ if (dmi_check_system(i8042_dmi_noselftest_table))
+ i8042_reset = I8042_RESET_NEVER;
+ }
if (dmi_check_system(i8042_dmi_noloop_table))
i8042_noloop = true;
module_param_named(unlock, i8042_unlock, bool, 0);
MODULE_PARM_DESC(unlock, "Ignore keyboard lock.");
-static bool i8042_reset;
-module_param_named(reset, i8042_reset, bool, 0);
-MODULE_PARM_DESC(reset, "Reset controller during init and cleanup.");
+enum i8042_controller_reset_mode {
+ I8042_RESET_NEVER,
+ I8042_RESET_ALWAYS,
+ I8042_RESET_ON_S2RAM,
+#define I8042_RESET_DEFAULT I8042_RESET_ON_S2RAM
+};
+static enum i8042_controller_reset_mode i8042_reset = I8042_RESET_DEFAULT;
+static int i8042_set_reset(const char *val, const struct kernel_param *kp)
+{
+ enum i8042_controller_reset_mode *arg = kp->arg;
+ int error;
+ bool reset;
+
+ if (val) {
+ error = kstrtobool(val, &reset);
+ if (error)
+ return error;
+ } else {
+ reset = true;
+ }
+
+ *arg = reset ? I8042_RESET_ALWAYS : I8042_RESET_NEVER;
+ return 0;
+}
+
+static const struct kernel_param_ops param_ops_reset_param = {
+ .flags = KERNEL_PARAM_OPS_FL_NOARG,
+ .set = i8042_set_reset,
+};
+#define param_check_reset_param(name, p) \
+ __param_check(name, p, enum i8042_controller_reset_mode)
+module_param_named(reset, i8042_reset, reset_param, 0);
+MODULE_PARM_DESC(reset, "Reset controller on resume, cleanup or both");
static bool i8042_direct;
module_param_named(direct, i8042_direct, bool, 0);
* Reset the controller and reset CRT to the original value set by BIOS.
*/
-static void i8042_controller_reset(bool force_reset)
+static void i8042_controller_reset(bool s2r_wants_reset)
{
i8042_flush();
* Reset the controller if requested.
*/
- if (i8042_reset || force_reset)
+ if (i8042_reset == I8042_RESET_ALWAYS ||
+ (i8042_reset == I8042_RESET_ON_S2RAM && s2r_wants_reset)) {
i8042_controller_selftest();
+ }
/*
* Restore the original control register setting.
* before suspending.
*/
-static int i8042_controller_resume(bool force_reset)
+static int i8042_controller_resume(bool s2r_wants_reset)
{
int error;
if (error)
return error;
- if (i8042_reset || force_reset) {
+ if (i8042_reset == I8042_RESET_ALWAYS ||
+ (i8042_reset == I8042_RESET_ON_S2RAM && s2r_wants_reset)) {
error = i8042_controller_selftest();
if (error)
return error;
static int i8042_pm_resume(struct device *dev)
{
- bool force_reset;
+ bool want_reset;
int i;
for (i = 0; i < I8042_NUM_PORTS; i++) {
* off control to the platform firmware, otherwise we can simply restore
* the mode.
*/
- force_reset = pm_resume_via_firmware();
+ want_reset = pm_resume_via_firmware();
- return i8042_controller_resume(force_reset);
+ return i8042_controller_resume(want_reset);
}
static int i8042_pm_thaw(struct device *dev)
i8042_platform_device = dev;
- if (i8042_reset) {
+ if (i8042_reset == I8042_RESET_ALWAYS) {
error = i8042_controller_selftest();
if (error)
return error;
char phys[32];
char product_name[16];
+ char ic_name[4];
unsigned int max_x;
unsigned int max_y;
dev_dbg(&ts->client->dev, "product name: %.*s\n",
(int)sizeof(ts->product_name), ts->product_name);
+ /* IC name */
+ cmd[0] = MIP4_R0_INFO;
+ cmd[1] = MIP4_R1_INFO_IC_NAME;
+ error = mip4_i2c_xfer(ts, cmd, sizeof(cmd),
+ ts->ic_name, sizeof(ts->ic_name));
+ if (error)
+ dev_warn(&ts->client->dev,
+ "Failed to retrieve IC name: %d\n", error);
+ else
+ dev_dbg(&ts->client->dev, "IC name: %.*s\n",
+ (int)sizeof(ts->ic_name), ts->ic_name);
+
/* Firmware version */
error = mip4_get_fw_version(ts);
if (error)
* paired with current firmware in the chip.
*/
count = snprintf(buf, PAGE_SIZE, "%.*s\n",
- (int)sizeof(ts->product_name), ts->product_name);
+ (int)sizeof(ts->product_name), ts->product_name);
mutex_unlock(&ts->input->mutex);
static DEVICE_ATTR(hw_version, S_IRUGO, mip4_sysfs_read_hw_version, NULL);
+static ssize_t mip4_sysfs_read_ic_name(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct mip4_ts *ts = i2c_get_clientdata(client);
+ size_t count;
+
+ mutex_lock(&ts->input->mutex);
+
+ count = snprintf(buf, PAGE_SIZE, "%.*s\n",
+ (int)sizeof(ts->ic_name), ts->ic_name);
+
+ mutex_unlock(&ts->input->mutex);
+
+ return count;
+}
+
+static DEVICE_ATTR(ic_name, S_IRUGO, mip4_sysfs_read_ic_name, NULL);
+
static struct attribute *mip4_attrs[] = {
&dev_attr_fw_version.attr,
&dev_attr_hw_version.attr,
+ &dev_attr_ic_name.attr,
&dev_attr_update_fw.attr,
NULL,
};
module_i2c_driver(mip4_driver);
MODULE_DESCRIPTION("MELFAS MIP4 Touchscreen");
-MODULE_VERSION("2016.03.12");
+MODULE_VERSION("2016.09.28");
MODULE_AUTHOR("Sangwon Jee <jeesw@melfas.com>");
MODULE_LICENSE("GPL");
projects / cascardo / linux.git / commitdiff