--- /dev/null
+* ST-Ericsson UX500 PM Domains
+
+UX500 supports multiple PM domains which are used to gate power to one or
+more peripherals on the SOC.
+
+The implementation of PM domains for UX500 are based upon the generic PM domain
+and use the corresponding DT bindings.
+
+==PM domain providers==
+
+Required properties:
+ - compatible: Must be "stericsson,ux500-pm-domains".
+ - #power-domain-cells : Number of cells in a power domain specifier, must be 1.
+
+Example:
+ pm_domains: pm_domains0 {
+ compatible = "stericsson,ux500-pm-domains";
+ #power-domain-cells = <1>;
+ };
+
+==PM domain consumers==
+
+Required properties:
+ - power-domains: A phandle and PM domain specifier. Below are the list of
+ valid specifiers:
+
+ Index Specifier
+ ----- ---------
+ 0 DOMAIN_VAPE
+
+Example:
+ sdi0_per1@80126000 {
+ compatible = "arm,pl18x", "arm,primecell";
+ power-domains = <&pm_domains DOMAIN_VAPE>
+ };
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/mfd/dbx500-prcmu.h>
+#include <dt-bindings/arm/ux500_pm_domains.h>
#include "skeleton.dtsi"
/ {
interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>;
};
+ pm_domains: pm_domains0 {
+ compatible = "stericsson,ux500-pm-domains";
+ #power-domain-cells = <1>;
+ };
clocks {
compatible = "stericsson,u8500-clks";
clock-frequency = <400000>;
clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>;
clock-names = "i2cclk", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
i2c@80122000 {
clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>;
clock-names = "i2cclk", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
i2c@80128000 {
clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>;
clock-names = "i2cclk", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
i2c@80110000 {
clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>;
clock-names = "i2cclk", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
i2c@8012a000 {
clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>;
clock-names = "i2cclk", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
ssp@80002000 {
dmas = <&dma 8 0 0x2>, /* Logical - DevToMem */
<&dma 8 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
ssp@80003000 {
dmas = <&dma 9 0 0x2>, /* Logical - DevToMem */
<&dma 9 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
spi@8011a000 {
dmas = <&dma 0 0 0x2>, /* Logical - DevToMem */
<&dma 0 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
spi@80112000 {
dmas = <&dma 35 0 0x2>, /* Logical - DevToMem */
<&dma 35 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
spi@80111000 {
dmas = <&dma 33 0 0x2>, /* Logical - DevToMem */
<&dma 33 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
spi@80129000 {
dmas = <&dma 40 0 0x2>, /* Logical - DevToMem */
<&dma 40 0 0x0>; /* Logical - MemToDev */
dma-names = "rx", "tx";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
};
uart@80120000 {
clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
clock-names = "sdi", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
status = "disabled";
};
clocks = <&prcc_kclk 2 4>, <&prcc_pclk 2 6>;
clock-names = "sdi", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
status = "disabled";
};
clocks = <&prcc_kclk 3 4>, <&prcc_pclk 3 4>;
clock-names = "sdi", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
status = "disabled";
};
clocks = <&prcc_kclk 2 5>, <&prcc_pclk 2 7>;
clock-names = "sdi", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
status = "disabled";
};
clocks = <&prcc_kclk 2 2>, <&prcc_pclk 2 4>;
clock-names = "sdi", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
status = "disabled";
};
clocks = <&prcc_kclk 3 7>, <&prcc_pclk 3 7>;
clock-names = "sdi", "apb_pclk";
+ power-domains = <&pm_domains DOMAIN_VAPE>;
status = "disabled";
};
"in 8bit mode\n");
status = spi_w8r8(spi, 0xAA);
if (status < 0)
- pr_warning("Siple test 1: FAILURE: spi_write_then_read "
- "failed with status %d\n", status);
+ pr_warn("Simple test 1: FAILURE: spi_write_then_read failed with status %d\n",
+ status);
else
pr_info("Simple test 1: SUCCESS!\n");
"in 8bit mode (full FIFO)\n");
status = spi_write_then_read(spi, &txbuf[0], 8, &rxbuf[0], 8);
if (status < 0)
- pr_warning("Simple test 2: FAILURE: spi_write_then_read() "
- "failed with status %d\n", status);
+ pr_warn("Simple test 2: FAILURE: spi_write_then_read() failed with status %d\n",
+ status);
else
pr_info("Simple test 2: SUCCESS!\n");
"in 8bit mode (see if we overflow FIFO)\n");
status = spi_write_then_read(spi, &txbuf[0], 14, &rxbuf[0], 14);
if (status < 0)
- pr_warning("Simple test 3: FAILURE: failed with status %d "
- "(probably FIFO overrun)\n", status);
+ pr_warn("Simple test 3: FAILURE: failed with status %d (probably FIFO overrun)\n",
+ status);
else
pr_info("Simple test 3: SUCCESS!\n");
"bytes garbage with spi_read() in 8bit mode\n");
status = spi_write(spi, &txbuf[0], 8);
if (status < 0)
- pr_warning("Simple test 4 step 1: FAILURE: spi_write() "
- "failed with status %d\n", status);
+ pr_warn("Simple test 4 step 1: FAILURE: spi_write() failed with status %d\n",
+ status);
else
pr_info("Simple test 4 step 1: SUCCESS!\n");
status = spi_read(spi, &rxbuf[0], 8);
if (status < 0)
- pr_warning("Simple test 4 step 2: FAILURE: spi_read() "
- "failed with status %d\n", status);
+ pr_warn("Simple test 4 step 2: FAILURE: spi_read() failed with status %d\n",
+ status);
else
pr_info("Simple test 4 step 2: SUCCESS!\n");
"14 bytes garbage with spi_read() in 8bit mode\n");
status = spi_write(spi, &txbuf[0], 14);
if (status < 0)
- pr_warning("Simple test 5 step 1: FAILURE: spi_write() "
- "failed with status %d (probably FIFO overrun)\n",
- status);
+ pr_warn("Simple test 5 step 1: FAILURE: spi_write() failed with status %d (probably FIFO overrun)\n",
+ status);
else
pr_info("Simple test 5 step 1: SUCCESS!\n");
status = spi_read(spi, &rxbuf[0], 14);
if (status < 0)
- pr_warning("Simple test 5 step 2: FAILURE: spi_read() "
- "failed with status %d (probably FIFO overrun)\n",
- status);
+ pr_warn("Simple test 5 step 2: FAILURE: spi_read() failed with status %d (probably FIFO overrun)\n",
+ status);
else
pr_info("Simple test 5: SUCCESS!\n");
DMA_TEST_SIZE, DMA_TEST_SIZE);
status = spi_write(spi, &bigtxbuf_virtual[0], DMA_TEST_SIZE);
if (status < 0)
- pr_warning("Simple test 6 step 1: FAILURE: spi_write() "
- "failed with status %d (probably FIFO overrun)\n",
- status);
+ pr_warn("Simple test 6 step 1: FAILURE: spi_write() failed with status %d (probably FIFO overrun)\n",
+ status);
else
pr_info("Simple test 6 step 1: SUCCESS!\n");
status = spi_read(spi, &bigrxbuf_virtual[0], DMA_TEST_SIZE);
if (status < 0)
- pr_warning("Simple test 6 step 2: FAILURE: spi_read() "
- "failed with status %d (probably FIFO overrun)\n",
- status);
+ pr_warn("Simple test 6 step 2: FAILURE: spi_read() failed with status %d (probably FIFO overrun)\n",
+ status);
else
pr_info("Simple test 6: SUCCESS!\n");
pr_info("Simple test 7: SUCCESS! (expected failure with "
"status EIO)\n");
else if (status < 0)
- pr_warning("Siple test 7: FAILURE: spi_write_then_read "
- "failed with status %d\n", status);
+ pr_warn("Simple test 7: FAILURE: spi_write_then_read failed with status %d\n",
+ status);
else
- pr_warning("Siple test 7: FAILURE: spi_write_then_read "
- "succeeded but it was expected to fail!\n");
+ pr_warn("Simple test 7: FAILURE: spi_write_then_read succeeded but it was expected to fail!\n");
pr_info("Simple test 8: write 8 bytes, read back 8 bytes garbage "
"in 16bit mode (full FIFO)\n");
status = spi_write_then_read(spi, &txbuf[0], 8, &rxbuf[0], 8);
if (status < 0)
- pr_warning("Simple test 8: FAILURE: spi_write_then_read() "
- "failed with status %d\n", status);
+ pr_warn("Simple test 8: FAILURE: spi_write_then_read() failed with status %d\n",
+ status);
else
pr_info("Simple test 8: SUCCESS!\n");
"in 16bit mode (see if we overflow FIFO)\n");
status = spi_write_then_read(spi, &txbuf[0], 14, &rxbuf[0], 14);
if (status < 0)
- pr_warning("Simple test 9: FAILURE: failed with status %d "
- "(probably FIFO overrun)\n", status);
+ pr_warn("Simple test 9: FAILURE: failed with status %d (probably FIFO overrun)\n",
+ status);
else
pr_info("Simple test 9: SUCCESS!\n");
DMA_TEST_SIZE, DMA_TEST_SIZE);
status = spi_write(spi, &bigtxbuf_virtual[0], DMA_TEST_SIZE);
if (status < 0)
- pr_warning("Simple test 10 step 1: FAILURE: spi_write() "
- "failed with status %d (probably FIFO overrun)\n",
- status);
+ pr_warn("Simple test 10 step 1: FAILURE: spi_write() failed with status %d (probably FIFO overrun)\n",
+ status);
else
pr_info("Simple test 10 step 1: SUCCESS!\n");
status = spi_read(spi, &bigrxbuf_virtual[0], DMA_TEST_SIZE);
if (status < 0)
- pr_warning("Simple test 10 step 2: FAILURE: spi_read() "
- "failed with status %d (probably FIFO overrun)\n",
- status);
+ pr_warn("Simple test 10 step 2: FAILURE: spi_read() failed with status %d (probably FIFO overrun)\n",
+ status);
else
pr_info("Simple test 10: SUCCESS!\n");
select PINCTRL_AB8540
select REGULATOR
select REGULATOR_DB8500_PRCMU
+ select PM_GENERIC_DOMAINS if PM
config MACH_MOP500
bool "U8500 Development platform, MOP500 versions"
board-mop500-audio.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
+obj-$(CONFIG_PM_GENERIC_DOMAINS) += pm_domains.o
CFLAGS_hotplug.o += -march=armv7-a
#include <linux/platform_data/arm-ux500-pm.h>
#include "db8500-regs.h"
+#include "pm_domains.h"
/* ARM WFI Standby signal register */
#define PRCM_ARM_WFI_STANDBY (prcmu_base + 0x130)
/* Set up ux500 suspend callbacks. */
suspend_set_ops(UX500_SUSPEND_OPS);
+
+ /* Initialize ux500 power domains */
+ ux500_pm_domains_init();
}
--- /dev/null
+/*
+ * Copyright (C) 2014 Linaro Ltd.
+ *
+ * Author: Ulf Hansson <ulf.hansson@linaro.org>
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * Implements PM domains using the generic PM domain for ux500.
+ */
+#include <linux/printk.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/of.h>
+#include <linux/pm_domain.h>
+
+#include <dt-bindings/arm/ux500_pm_domains.h>
+#include "pm_domains.h"
+
+static int pd_power_off(struct generic_pm_domain *domain)
+{
+ /*
+ * Handle the gating of the PM domain regulator here.
+ *
+ * Drivers/subsystems handling devices in the PM domain needs to perform
+ * register context save/restore from their respective runtime PM
+ * callbacks, to be able to enable PM domain gating/ungating.
+ */
+ return 0;
+}
+
+static int pd_power_on(struct generic_pm_domain *domain)
+{
+ /*
+ * Handle the ungating of the PM domain regulator here.
+ *
+ * Drivers/subsystems handling devices in the PM domain needs to perform
+ * register context save/restore from their respective runtime PM
+ * callbacks, to be able to enable PM domain gating/ungating.
+ */
+ return 0;
+}
+
+static struct generic_pm_domain ux500_pm_domain_vape = {
+ .name = "VAPE",
+ .power_off = pd_power_off,
+ .power_on = pd_power_on,
+};
+
+static struct generic_pm_domain *ux500_pm_domains[NR_DOMAINS] = {
+ [DOMAIN_VAPE] = &ux500_pm_domain_vape,
+};
+
+static struct of_device_id ux500_pm_domain_matches[] = {
+ { .compatible = "stericsson,ux500-pm-domains", },
+ { },
+};
+
+int __init ux500_pm_domains_init(void)
+{
+ struct device_node *np;
+ struct genpd_onecell_data *genpd_data;
+ int i;
+
+ np = of_find_matching_node(NULL, ux500_pm_domain_matches);
+ if (!np)
+ return -ENODEV;
+
+ genpd_data = kzalloc(sizeof(*genpd_data), GFP_KERNEL);
+ if (!genpd_data)
+ return -ENOMEM;
+
+ genpd_data->domains = ux500_pm_domains;
+ genpd_data->num_domains = ARRAY_SIZE(ux500_pm_domains);
+
+ for (i = 0; i < ARRAY_SIZE(ux500_pm_domains); ++i)
+ pm_genpd_init(ux500_pm_domains[i], NULL, false);
+
+ of_genpd_add_provider_onecell(np, genpd_data);
+ return 0;
+}
--- /dev/null
+/*
+ * Copyright (C) 2014 Linaro Ltd.
+ *
+ * Author: Ulf Hansson <ulf.hansson@linaro.org>
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+#ifndef __MACH_UX500_PM_DOMAINS_H
+#define __MACH_UX500_PM_DOMAINS_H
+
+#ifdef CONFIG_PM_GENERIC_DOMAINS
+extern int __init ux500_pm_domains_init(void);
+#else
+static inline int ux500_pm_domains_init(void) { return 0; }
+#endif
+
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2014 Linaro Ltd.
+ *
+ * Author: Ulf Hansson <ulf.hansson@linaro.org>
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifndef _DT_BINDINGS_ARM_UX500_PM_DOMAINS_H
+#define _DT_BINDINGS_ARM_UX500_PM_DOMAINS_H
+
+#define DOMAIN_VAPE 0
+
+/* Number of PM domains. */
+#define NR_DOMAINS (DOMAIN_VAPE + 1)
+
+#endif
projects / cascardo / linux.git / commitdiff