/ getpagesize();
p = get_pages(pages);
+ /* Initialize the virtqueue */
+ vq->next = NULL;
+ vq->last_avail_idx = 0;
+ vq->dev = dev;
+
/* Initialize the configuration. */
vq->config.num = num_descs;
vq->config.irq = devices.next_irq++;
for (i = &dev->vq; *i; i = &(*i)->next);
*i = vq;
- /* Link virtqueue back to device. */
- vq->dev = dev;
-
/* Set the routine to call when the Guest does something to this
* virtqueue. */
vq->handle_output = handle_output;
dev->desc = new_dev_desc(type);
dev->handle_input = handle_input;
dev->name = name;
+ dev->vq = NULL;
return dev;
}
('port'). Once you have done that, you will be able to use
parport_claim and parport_release in order to use the port.
+The ('name') argument is the name of the device that appears in /proc
+filesystem. The string must be valid for the whole lifetime of the
+device (until parport_unregister_device is called).
+
This function will register three callbacks into your driver:
'preempt', 'wakeup' and 'irq'. Each of these may be NULL in order to
indicate that you do not want a callback.
MAC addresses passed by the firmware when no information other
than indices is available to associate an address with a device.
- phy-connection-type : a string naming the controller/PHY interface type,
- i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "tbi",
- or "rtbi".
+ i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
+ Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
+ "tbi", or "rtbi".
Example:
ucc@2000 {
ThinkPad ACPI Extras Driver
- Version 0.16
- August 2nd, 2007
+ Version 0.17
+ October 04th, 2007
Borislav Deianov <borislav@users.sf.net>
Henrique de Moraes Holschuh <hmh@hmh.eng.br>
This feature allows software control of the LCD brightness on ThinkPad
models which don't have a hardware brightness slider.
-It has some limitations: the LCD backlight cannot be actually turned on or off
-by this interface, and in many ThinkPad models, the "dim while on battery"
-functionality will be enabled by the BIOS when this interface is used, and
-cannot be controlled.
-
-The backlight control has eight levels, ranging from 0 to 7. Some of the
-levels may not be distinct.
-
-There are two interfaces to the firmware for brightness control, EC and CMOS.
-To select which one should be used, use the brightness_mode module parameter:
-brightness_mode=1 selects EC mode, brightness_mode=2 selects CMOS mode,
-brightness_mode=3 selects both EC and CMOS. The driver tries to autodetect
-which interface to use.
+It has some limitations: the LCD backlight cannot be actually turned on or
+off by this interface, and in many ThinkPad models, the "dim while on
+battery" functionality will be enabled by the BIOS when this interface is
+used, and cannot be controlled.
+
+On IBM (and some of the earlier Lenovo) ThinkPads, the backlight control
+has eight brightness levels, ranging from 0 to 7. Some of the levels
+may not be distinct. Later Lenovo models that implement the ACPI
+display backlight brightness control methods have 16 levels, ranging
+from 0 to 15.
+
+There are two interfaces to the firmware for direct brightness control,
+EC and CMOS. To select which one should be used, use the
+brightness_mode module parameter: brightness_mode=1 selects EC mode,
+brightness_mode=2 selects CMOS mode, brightness_mode=3 selects both EC
+and CMOS. The driver tries to autodetect which interface to use.
+
+When display backlight brightness controls are available through the
+standard ACPI interface, it is best to use it instead of this direct
+ThinkPad-specific interface. The driver will disable its native
+backlight brightness control interface if it detects that the standard
+ACPI interface is available in the ThinkPad.
+
+The brightness_enable module parameter can be used to control whether
+the LCD brightness control feature will be enabled when available.
+brightness_enable=0 forces it to be disabled. brightness_enable=1
+forces it to be enabled when available, even if the standard ACPI
+interface is also available.
Procfs notes:
Sysfs notes:
-The interface is implemented through the backlight sysfs class, which is poorly
-documented at this time.
+The interface is implemented through the backlight sysfs class, which is
+poorly documented at this time.
-Locate the thinkpad_screen device under /sys/class/backlight, and inside it
-there will be the following attributes:
+Locate the thinkpad_screen device under /sys/class/backlight, and inside
+it there will be the following attributes:
max_brightness:
Reads the maximum brightness the hardware can be set to.
Reads what brightness the screen is set to at this instant.
brightness:
- Writes request the driver to change brightness to the given
- value. Reads will tell you what brightness the driver is trying
- to set the display to when "power" is set to zero and the display
- has not been dimmed by a kernel power management event.
+ Writes request the driver to change brightness to the
+ given value. Reads will tell you what brightness the
+ driver is trying to set the display to when "power" is set
+ to zero and the display has not been dimmed by a kernel
+ power management event.
power:
- power management mode, where 0 is "display on", and 1 to 3 will
- dim the display backlight to brightness level 0 because
- thinkpad-acpi cannot really turn the backlight off. Kernel
- power management events can temporarily increase the current
- power management level, i.e. they can dim the display.
+ power management mode, where 0 is "display on", and 1 to 3
+ will dim the display backlight to brightness level 0
+ because thinkpad-acpi cannot really turn the backlight
+ off. Kernel power management events can temporarily
+ increase the current power management level, i.e. they can
+ dim the display.
Volume control -- /proc/acpi/ibm/volume
P: Joshua Thompson
M: funaho@jurai.org
W: http://www.mac.linux-m68k.org/
-L: linux-mac68k@mac.linux-m68k.org
+L: linux-m68k@lists.linux-m68k.org
S: Maintained
M68K ON HP9000/300
static int atari_keyb_done = 0;
-int __init atari_keyb_init(void)
+int atari_keyb_init(void)
{
if (atari_keyb_done)
return 0;
atari_keyb_done = 1;
return 0;
}
+EXPORT_SYMBOL_GPL(atari_keyb_init);
int atari_kbd_translate(unsigned char keycode, unsigned char *keycodep, char raw_mode)
{
config BASLER_EXCITE
bool "Basler eXcite smart camera"
select CEVT_R4K
+ select CSRC_R4K
select DMA_COHERENT
select HW_HAS_PCI
select IRQ_CPU
config BCM47XX
bool "BCM47XX based boards"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
config MIPS_COBALT
bool "Cobalt Server"
select CEVT_R4K
+ select CSRC_R4K
select CEVT_GT641XX
select DMA_NONCOHERENT
select HW_HAS_PCI
bool "DECstations"
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select NO_IOPORT
select IRQ_CPU
select ARC32
select ARCH_MAY_HAVE_PC_FDC
select CEVT_R4K
+ select CSRC_R4K
select GENERIC_ISA_DMA
select IRQ_CPU
select I8253
config LASAT
bool "LASAT Networks platforms"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
select HW_HAS_PCI
bool "Lemote Fulong mini-PC"
select ARCH_SPARSEMEM_ENABLE
select CEVT_R4K
+ select CSRC_R4K
select SYS_HAS_CPU_LOONGSON2
select DMA_NONCOHERENT
select BOOT_ELF32
bool "MIPS Atlas board"
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
select IRQ_CPU
select ARCH_MAY_HAVE_PC_FDC
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select GENERIC_ISA_DMA
select IRQ_CPU
config MIPS_SEAD
bool "MIPS SEAD board"
select CEVT_R4K
+ select CSRC_R4K
select IRQ_CPU
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
config MIPS_SIM
bool 'MIPS simulator (MIPSsim)'
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
select IRQ_CPU
config MARKEINS
bool "NEC EMMA2RH Mark-eins"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
config MACH_VR41XX
bool "NEC VR4100 series based machines"
select CEVT_R4K
+ select CSRC_R4K
select SYS_HAS_CPU_VR41XX
select GENERIC_HARDIRQS_NO__DO_IRQ
config PMC_YOSEMITE
bool "PMC-Sierra Yosemite eval board"
select CEVT_R4K
+ select CSRC_R4K
select DMA_COHERENT
select HW_HAS_PCI
select IRQ_CPU
config QEMU
bool "Qemu"
select CEVT_R4K
+ select CSRC_R4K
select DMA_COHERENT
select GENERIC_ISA_DMA
select HAVE_STD_PC_SERIAL_PORT
select ARC32
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_EISA
select I8253
+ select I8259
select IP22_CPU_SCACHE
select IRQ_CPU
select GENERIC_ISA_DMA_SUPPORT_BROKEN
select ARC32
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select ZONE_DMA32 if 64BIT
config SIBYTE_LITTLESUR
bool "Sibyte BCM91250C2-LittleSur"
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select ZONE_DMA32 if 64BIT
config SNI_RM
bool "SNI RM200/300/400"
select ARCH_MAY_HAVE_PC_FDC
select BOOT_ELF32
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select GENERIC_ISA_DMA
select HW_HAS_EISA
config TOSHIBA_RBTX4927
bool "Toshiba RBTX49[23]7 board"
select CEVT_R4K
+ select CSRC_R4K
select CEVT_TXX9
select DMA_NONCOHERENT
select HAS_TXX9_SERIAL
config TOSHIBA_RBTX4938
bool "Toshiba RBTX4938 board"
select CEVT_R4K
+ select CSRC_R4K
select CEVT_TXX9
select DMA_NONCOHERENT
select HAS_TXX9_SERIAL
config WR_PPMC
bool "Wind River PPMC board"
select CEVT_R4K
+ select CSRC_R4K
select IRQ_CPU
select BOOT_ELF32
select DMA_NONCOHERENT
config CSRC_BCM1480
bool
+config CSRC_R4K
+ bool
+
config CSRC_SB1250
bool
or have huge holes in the physical address space for other reasons.
See <file:Documentation/vm/numa> for more.
+config ARCH_POPULATES_NODE_MAP
+ def_bool y
+
config ARCH_SPARSEMEM_ENABLE
bool
select SPARSEMEM_STATIC
config PCSPEAKER
bool
+config ZONE_DMA32
+ bool
+
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
bool
select 64BIT_PHYS_ADDR
select CEVT_R4K
+ select CSRC_R4K
select IRQ_CPU
select SYS_HAS_CPU_MIPS32_R1
select SYS_SUPPORTS_32BIT_KERNEL
obj-$(CONFIG_CEVT_SB1250) += cevt-sb1250.o
obj-$(CONFIG_CEVT_TXX9) += cevt-txx9.o
obj-$(CONFIG_CSRC_BCM1480) += csrc-bcm1480.o
+obj-$(CONFIG_CSRC_R4K) += csrc-r4k.o
obj-$(CONFIG_CSRC_SB1250) += csrc-sb1250.o
binfmt_irix-objs := irixelf.o irixinv.o irixioctl.o irixsig.o \
obj-$(CONFIG_CPU_VR41XX) += r4k_fpu.o r4k_switch.o
obj-$(CONFIG_SMP) += smp.o
+obj-$(CONFIG_SMP_UP) += smp-up.o
obj-$(CONFIG_MIPS_MT) += mips-mt.o
obj-$(CONFIG_MIPS_MT_FPAFF) += mips-mt-fpaff.o
return 1;
}
-void __cpuinit mips_clockevent_init(void)
+int __cpuinit mips_clockevent_init(void)
{
uint64_t mips_freq = mips_hpt_frequency;
unsigned int cpu = smp_processor_id();
unsigned int irq;
if (!cpu_has_counter || !mips_hpt_frequency)
- return;
+ return -ENXIO;
#ifdef CONFIG_MIPS_MT_SMTC
setup_smtc_dummy_clockevent_device();
* device.
*/
if (cpu)
- return;
+ return 0;
#endif
if (!c0_compare_int_usable())
- return;
+ return -ENXIO;
/*
* With vectored interrupts things are getting platform specific.
clockevents_register_device(cd);
- if (!cp0_timer_irq_installed)
- return;
+ if (cp0_timer_irq_installed)
+ return 0;
cp0_timer_irq_installed = 1;
#else
setup_irq(irq, &c0_compare_irqaction);
#endif
+
+ return 0;
}
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2007 by Ralf Baechle
+ */
+
+static cycle_t c0_hpt_read(void)
+{
+ return read_c0_count();
+}
+
+static struct clocksource clocksource_mips = {
+ .name = "MIPS",
+ .read = c0_hpt_read,
+ .mask = CLOCKSOURCE_MASK(32),
+ .flags = CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+static void __init init_mips_clocksource(void)
+{
+ /* Calclate a somewhat reasonable rating value */
+ clocksource_mips.rating = 200 + mips_hpt_frequency / 10000000;
+
+ clocksource_set_clock(&clocksource_mips, mips_hpt_frequency);
+
+ clocksource_register(&clocksource_mips);
+}
static void __init bootmem_init(void)
{
- unsigned long reserved_end;
+ unsigned long init_begin, reserved_end;
unsigned long mapstart = ~0UL;
unsigned long bootmap_size;
int i;
*/
bootmap_size = init_bootmem_node(NODE_DATA(0), mapstart,
min_low_pfn, max_low_pfn);
+
+
+ init_begin = PFN_UP(__pa_symbol(&__init_begin));
+ for (i = 0; i < boot_mem_map.nr_map; i++) {
+ unsigned long start, end;
+
+ start = PFN_UP(boot_mem_map.map[i].addr);
+ end = PFN_DOWN(boot_mem_map.map[i].addr
+ + boot_mem_map.map[i].size);
+
+ if (start <= init_begin)
+ start = init_begin;
+ if (start >= end)
+ continue;
+
+#ifndef CONFIG_HIGHMEM
+ if (end > max_low_pfn)
+ end = max_low_pfn;
+
+ /*
+ * ... finally, is the area going away?
+ */
+ if (end <= start)
+ continue;
+#endif
+
+ add_active_range(0, start, end);
+ }
+
/*
* Register fully available low RAM pages with the bootmem allocator.
*/
--- /dev/null
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 2006, 07 by Ralf Baechle (ralf@linux-mips.org)
+ *
+ * Symmetric Uniprocessor (TM) Support
+ */
+#include <linux/kernel.h>
+#include <linux/sched.h>
+
+/*
+ * Send inter-processor interrupt
+ */
+void up_send_ipi_single(int cpu, unsigned int action)
+{
+ panic(KERN_ERR "%s called", __func__);
+}
+
+static inline void up_send_ipi_mask(cpumask_t mask, unsigned int action)
+{
+ panic(KERN_ERR "%s called", __func__);
+}
+
+/*
+ * After we've done initial boot, this function is called to allow the
+ * board code to clean up state, if needed
+ */
+void __cpuinit up_init_secondary(void)
+{
+}
+
+void __cpuinit up_smp_finish(void)
+{
+}
+
+/* Hook for after all CPUs are online */
+void up_cpus_done(void)
+{
+}
+
+/*
+ * Firmware CPU startup hook
+ */
+void __cpuinit up_boot_secondary(int cpu, struct task_struct *idle)
+{
+}
+
+void __init up_smp_setup(void)
+{
+}
+
+void __init up_prepare_cpus(unsigned int max_cpus)
+{
+}
+
+struct plat_smp_ops up_smp_ops = {
+ .send_ipi_single = up_send_ipi_single,
+ .send_ipi_mask = up_send_ipi_mask,
+ .init_secondary = up_init_secondary,
+ .smp_finish = up_smp_finish,
+ .cpus_done = up_cpus_done,
+ .boot_secondary = up_boot_secondary,
+ .smp_setup = up_smp_setup,
+ .prepare_cpus = up_prepare_cpus,
+};
return rtc_mips_set_mmss(now.tv_sec);
}
-/*
- * High precision timer functions for a R4k-compatible timer.
- */
-static cycle_t c0_hpt_read(void)
-{
- return read_c0_count();
-}
-
int (*mips_timer_state)(void);
int null_perf_irq(void)
unsigned int mips_hpt_frequency;
-static struct clocksource clocksource_mips = {
- .name = "MIPS",
- .read = c0_hpt_read,
- .mask = CLOCKSOURCE_MASK(32),
- .flags = CLOCK_SOURCE_IS_CONTINUOUS,
-};
-
-static unsigned int __init calibrate_hpt(void)
-{
- cycle_t frequency, hpt_start, hpt_end, hpt_count, hz;
-
- const int loops = HZ / 10;
- int log_2_loops = 0;
- int i;
-
- /*
- * We want to calibrate for 0.1s, but to avoid a 64-bit
- * division we round the number of loops up to the nearest
- * power of 2.
- */
- while (loops > 1 << log_2_loops)
- log_2_loops++;
- i = 1 << log_2_loops;
-
- /*
- * Wait for a rising edge of the timer interrupt.
- */
- while (mips_timer_state());
- while (!mips_timer_state());
-
- /*
- * Now see how many high precision timer ticks happen
- * during the calculated number of periods between timer
- * interrupts.
- */
- hpt_start = clocksource_mips.read();
- do {
- while (mips_timer_state());
- while (!mips_timer_state());
- } while (--i);
- hpt_end = clocksource_mips.read();
-
- hpt_count = (hpt_end - hpt_start) & clocksource_mips.mask;
- hz = HZ;
- frequency = hpt_count * hz;
-
- return frequency >> log_2_loops;
-}
-
void __init clocksource_set_clock(struct clocksource *cs, unsigned int clock)
{
u64 temp;
cd->mult = (u32) temp;
}
-static void __init init_mips_clocksource(void)
-{
- /* Calclate a somewhat reasonable rating value */
- clocksource_mips.rating = 200 + mips_hpt_frequency / 10000000;
-
- clocksource_set_clock(&clocksource_mips, mips_hpt_frequency);
-
- clocksource_register(&clocksource_mips);
-}
-
void __init __weak plat_time_init(void)
{
}
BUG();
}
+static __init int cpu_has_mfc0_count_bug(void)
+{
+ switch (current_cpu_type()) {
+ case CPU_R4000PC:
+ case CPU_R4000SC:
+ case CPU_R4000MC:
+ /*
+ * V3.0 is documented as suffering from the mfc0 from count bug.
+ * Afaik this is the last version of the R4000. Later versions
+ * were marketed as R4400.
+ */
+ return 1;
+
+ case CPU_R4400PC:
+ case CPU_R4400SC:
+ case CPU_R4400MC:
+ /*
+ * The published errata for the R4400 upto 3.0 say the CPU
+ * has the mfc0 from count bug.
+ */
+ if ((current_cpu_data.processor_id & 0xff) <= 0x30)
+ return 1;
+
+ /*
+ * I don't have erratas for newer R4400 so be paranoid.
+ */
+ return 1;
+ }
+
+ return 0;
+}
+
void __init time_init(void)
{
plat_time_init();
- if (cpu_has_counter && (mips_hpt_frequency || mips_timer_state)) {
- /* We know counter frequency. Or we can get it. */
- if (!mips_hpt_frequency)
- mips_hpt_frequency = calibrate_hpt();
-
- /* Report the high precision timer rate for a reference. */
- printk("Using %u.%03u MHz high precision timer.\n",
- ((mips_hpt_frequency + 500) / 1000) / 1000,
- ((mips_hpt_frequency + 500) / 1000) % 1000);
+ if (mips_clockevent_init() || !cpu_has_mfc0_count_bug())
init_mips_clocksource();
- }
-
- mips_clockevent_init();
}
*/
if (v != l->value) {
printk(KERN_DEBUG "VPE loader: "
- "apply_r_mips_lo16/hi16: "
+ "apply_r_mips_lo16/hi16: \t"
"inconsistent value information\n");
return -ENOEXEC;
}
break;
case SHN_MIPS_SCOMMON:
- printk(KERN_DEBUG "simplify_symbols: ignoring SHN_MIPS_SCOMMON"
+ printk(KERN_DEBUG "simplify_symbols: ignoring SHN_MIPS_SCOMMON "
"symbol <%s> st_shndx %d\n", strtab + sym[i].st_name,
sym[i].st_shndx);
// .sbss section
ax.rv.si = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.si;
}
ax.rv.di = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.di;
}
ax.rv.dp = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.dp;
}
ax.rv.dp = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.dp;
}
ax.rv.sp = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.sp;
}
ax.rv.sp = r;
va_start(ax.ap, op);
ieee754_xcpt(&ax);
+ va_end(ax.ap);
return ax.rv.sp;
}
void __init plat_time_init(void)
{
- unsigned int est_freq, flags;
-
- local_irq_save(flags);
+ unsigned int est_freq;
/* Set Data mode - binary. */
CMOS_WRITE(CMOS_READ(RTC_CONTROL) | RTC_DM_BINARY, RTC_CONTROL);
(est_freq % 1000000) * 100 / 1000000);
cpu_khz = est_freq / 1000;
-
- local_irq_restore(flags);
}
current_cpu_type() == CPU_R12000);
}
+static gfp_t massage_gfp_flags(const struct device *dev, gfp_t gfp)
+{
+ /* ignore region specifiers */
+ gfp &= ~(__GFP_DMA | __GFP_DMA32 | __GFP_HIGHMEM);
+
+#ifdef CONFIG_ZONE_DMA32
+ if (dev == NULL)
+ gfp |= __GFP_DMA;
+ else if (dev->coherent_dma_mask < DMA_BIT_MASK(24))
+ gfp |= __GFP_DMA;
+ else
+#endif
+#ifdef CONFIG_ZONE_DMA32
+ if (dev->coherent_dma_mask < DMA_BIT_MASK(32))
+ gfp |= __GFP_DMA32;
+ else
+#endif
+ ;
+
+ /* Don't invoke OOM killer */
+ gfp |= __GFP_NORETRY;
+
+ return gfp;
+}
+
void *dma_alloc_noncoherent(struct device *dev, size_t size,
dma_addr_t * dma_handle, gfp_t gfp)
{
void *ret;
- /* ignore region specifiers */
- gfp &= ~(__GFP_DMA | __GFP_HIGHMEM);
+ gfp = massage_gfp_flags(dev, gfp);
- if (dev == NULL || (dev->coherent_dma_mask < 0xffffffff))
- gfp |= GFP_DMA;
ret = (void *) __get_free_pages(gfp, get_order(size));
if (ret != NULL) {
{
void *ret;
- /* ignore region specifiers */
- gfp &= ~(__GFP_DMA | __GFP_HIGHMEM);
+ gfp = massage_gfp_flags(dev, gfp);
- if (dev == NULL || (dev->coherent_dma_mask < 0xffffffff))
- gfp |= GFP_DMA;
ret = (void *) __get_free_pages(gfp, get_order(size));
if (ret) {
* so we can't guarantee allocations that must be
* within a tighter range than GFP_DMA..
*/
- if (mask < 0x00ffffff)
+ if (mask < DMA_BIT_MASK(24))
return 0;
return 1;
void __init paging_init(void)
{
- unsigned long zones_size[MAX_NR_ZONES] = { 0, };
-#ifndef CONFIG_FLATMEM
- unsigned long zholes_size[MAX_NR_ZONES] = { 0, };
- unsigned long i, j, pfn;
-#endif
+ unsigned long max_zone_pfns[MAX_NR_ZONES];
+ unsigned long lastpfn;
pagetable_init();
kmap_coherent_init();
#ifdef CONFIG_ZONE_DMA
- if (min_low_pfn < MAX_DMA_PFN && MAX_DMA_PFN <= max_low_pfn) {
- zones_size[ZONE_DMA] = MAX_DMA_PFN - min_low_pfn;
- zones_size[ZONE_NORMAL] = max_low_pfn - MAX_DMA_PFN;
- } else if (max_low_pfn < MAX_DMA_PFN)
- zones_size[ZONE_DMA] = max_low_pfn - min_low_pfn;
- else
+ max_zone_pfns[ZONE_DMA] = MAX_DMA_PFN;
#endif
- zones_size[ZONE_NORMAL] = max_low_pfn - min_low_pfn;
-
+#ifdef CONFIG_ZONE_DMA32
+ max_zone_pfns[ZONE_DMA32] = MAX_DMA32_PFN;
+#endif
+ max_zone_pfns[ZONE_NORMAL] = max_low_pfn;
+ lastpfn = max_low_pfn;
#ifdef CONFIG_HIGHMEM
- zones_size[ZONE_HIGHMEM] = highend_pfn - highstart_pfn;
+ max_zone_pfns[ZONE_HIGHMEM] = highend_pfn;
+ lastpfn = highend_pfn;
- if (cpu_has_dc_aliases && zones_size[ZONE_HIGHMEM]) {
+ if (cpu_has_dc_aliases && max_low_pfn != highend_pfn) {
printk(KERN_WARNING "This processor doesn't support highmem."
- " %ldk highmem ignored\n", zones_size[ZONE_HIGHMEM]);
- zones_size[ZONE_HIGHMEM] = 0;
+ " %ldk highmem ignored\n",
+ (highend_pfn - max_low_pfn) << (PAGE_SHIFT - 10));
+ max_zone_pfns[ZONE_HIGHMEM] = max_low_pfn;
+ lastpfn = max_low_pfn;
}
#endif
-#ifdef CONFIG_FLATMEM
- free_area_init(zones_size);
-#else
- pfn = min_low_pfn;
- for (i = 0; i < MAX_NR_ZONES; i++)
- for (j = 0; j < zones_size[i]; j++, pfn++)
- if (!page_is_ram(pfn))
- zholes_size[i]++;
- free_area_init_node(0, NODE_DATA(0), zones_size, 0, zholes_size);
-#endif
+ free_area_init_nodes(max_zone_pfns);
}
static struct kcore_list kcore_mem, kcore_vmalloc;
config PMC_MSP4200_EVAL
bool "PMC-Sierra MSP4200 Eval Board"
select CEVT_R4K
+ select CSRC_R4K
select IRQ_MSP_SLP
select HW_HAS_PCI
config PMC_MSP4200_GW
bool "PMC-Sierra MSP4200 VoIP Gateway"
select CEVT_R4K
+ select CSRC_R4K
select IRQ_MSP_SLP
select HW_HAS_PCI
#include <asm/sgi/ioc.h>
#include <asm/sgi/mc.h>
#include <asm/sgi/ip22.h>
+#include <asm/i8259.h>
/* I2 has four EISA slots. */
#define IP22_EISA_MAX_SLOTS 4
return IRQ_NONE;
}
-static void enable_eisa1_irq(unsigned int irq)
-{
- u8 mask;
-
- mask = inb(EISA_INT1_MASK);
- mask &= ~((u8) (1 << irq));
- outb(mask, EISA_INT1_MASK);
-}
-
-static unsigned int startup_eisa1_irq(unsigned int irq)
-{
- u8 edge;
-
- /* Only use edge interrupts for EISA */
-
- edge = inb(EISA_INT1_EDGE_LEVEL);
- edge &= ~((u8) (1 << irq));
- outb(edge, EISA_INT1_EDGE_LEVEL);
-
- enable_eisa1_irq(irq);
- return 0;
-}
-
-static void disable_eisa1_irq(unsigned int irq)
-{
- u8 mask;
-
- mask = inb(EISA_INT1_MASK);
- mask |= ((u8) (1 << irq));
- outb(mask, EISA_INT1_MASK);
-}
-
-static void mask_and_ack_eisa1_irq(unsigned int irq)
-{
- disable_eisa1_irq(irq);
-
- outb(0x20, EISA_INT1_CTRL);
-}
-
-static void end_eisa1_irq(unsigned int irq)
-{
- if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- enable_eisa1_irq(irq);
-}
-
-static struct irq_chip ip22_eisa1_irq_type = {
- .name = "IP22 EISA",
- .startup = startup_eisa1_irq,
- .ack = mask_and_ack_eisa1_irq,
- .mask = disable_eisa1_irq,
- .mask_ack = mask_and_ack_eisa1_irq,
- .unmask = enable_eisa1_irq,
- .end = end_eisa1_irq,
-};
-
-static void enable_eisa2_irq(unsigned int irq)
-{
- u8 mask;
-
- mask = inb(EISA_INT2_MASK);
- mask &= ~((u8) (1 << (irq - 8)));
- outb(mask, EISA_INT2_MASK);
-}
-
-static unsigned int startup_eisa2_irq(unsigned int irq)
-{
- u8 edge;
-
- /* Only use edge interrupts for EISA */
-
- edge = inb(EISA_INT2_EDGE_LEVEL);
- edge &= ~((u8) (1 << (irq - 8)));
- outb(edge, EISA_INT2_EDGE_LEVEL);
-
- enable_eisa2_irq(irq);
- return 0;
-}
-
-static void disable_eisa2_irq(unsigned int irq)
-{
- u8 mask;
-
- mask = inb(EISA_INT2_MASK);
- mask |= ((u8) (1 << (irq - 8)));
- outb(mask, EISA_INT2_MASK);
-}
-
-static void mask_and_ack_eisa2_irq(unsigned int irq)
-{
- disable_eisa2_irq(irq);
-
- outb(0x20, EISA_INT2_CTRL);
-}
-
-static void end_eisa2_irq(unsigned int irq)
-{
- if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS)))
- enable_eisa2_irq(irq);
-}
-
-static struct irq_chip ip22_eisa2_irq_type = {
- .name = "IP22 EISA",
- .startup = startup_eisa2_irq,
- .ack = mask_and_ack_eisa2_irq,
- .mask = disable_eisa2_irq,
- .mask_ack = mask_and_ack_eisa2_irq,
- .unmask = enable_eisa2_irq,
- .end = end_eisa2_irq,
-};
-
static struct irqaction eisa_action = {
.handler = ip22_eisa_intr,
.name = "EISA",
};
-static struct irqaction cascade_action = {
- .handler = no_action,
- .name = "EISA cascade",
-};
-
int __init ip22_eisa_init(void)
{
int i, c;
outb(1, EISA_EXT_NMI_RESET_CTRL);
udelay(50); /* Wait long enough for the dust to settle */
outb(0, EISA_EXT_NMI_RESET_CTRL);
- outb(0x11, EISA_INT1_CTRL);
- outb(0x11, EISA_INT2_CTRL);
- outb(0, EISA_INT1_MASK);
- outb(8, EISA_INT2_MASK);
- outb(4, EISA_INT1_MASK);
- outb(2, EISA_INT2_MASK);
- outb(1, EISA_INT1_MASK);
- outb(1, EISA_INT2_MASK);
- outb(0xfb, EISA_INT1_MASK);
- outb(0xff, EISA_INT2_MASK);
outb(0, EISA_DMA2_WRITE_SINGLE);
- for (i = SGINT_EISA; i < (SGINT_EISA + EISA_MAX_IRQ); i++) {
- if (i < (SGINT_EISA + 8))
- set_irq_chip(i, &ip22_eisa1_irq_type);
- else
- set_irq_chip(i, &ip22_eisa2_irq_type);
- }
+ init_i8259_irqs();
/* Cannot use request_irq because of kmalloc not being ready at such
* an early stage. Yes, I've been bitten... */
setup_irq(SGI_EISA_IRQ, &eisa_action);
- setup_irq(SGINT_EISA + 2, &cascade_action);
EISA_bus = 1;
return 0;
for (x=0; x<100000; x++) __asm__ __volatile__(""); })
#define eeprom_cs_on(ptr) ({ \
- *ptr &= ~EEPROM_DATO; \
- *ptr &= ~EEPROM_ECLK; \
- *ptr &= ~EEPROM_EPROT; \
- delay(); \
- *ptr |= EEPROM_CSEL; \
- *ptr |= EEPROM_ECLK; })
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_DATO, ptr); \
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_ECLK, ptr); \
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_EPROT, ptr); \
+ delay(); \
+ __raw_writel(__raw_readl(ptr) | EEPROM_CSEL, ptr); \
+ __raw_writel(__raw_readl(ptr) | EEPROM_ECLK, ptr); })
#define eeprom_cs_off(ptr) ({ \
- *ptr &= ~EEPROM_ECLK; \
- *ptr &= ~EEPROM_CSEL; \
- *ptr |= EEPROM_EPROT; \
- *ptr |= EEPROM_ECLK; })
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_ECLK, ptr); \
+ __raw_writel(__raw_readl(ptr) & ~EEPROM_CSEL, ptr); \
+ __raw_writel(__raw_readl(ptr) | EEPROM_EPROT, ptr); \
+ __raw_writel(__raw_readl(ptr) | EEPROM_ECLK, ptr); })
#define BITS_IN_COMMAND 11
/*
ser_cmd = cmd | (reg << (16 - BITS_IN_COMMAND));
for (i = 0; i < BITS_IN_COMMAND; i++) {
if (ser_cmd & (1<<15)) /* if high order bit set */
- writel(readl(ctrl) | EEPROM_DATO, ctrl);
+ __raw_writel(__raw_readl(ctrl) | EEPROM_DATO, ctrl);
else
- writel(readl(ctrl) & ~EEPROM_DATO, ctrl);
- writel(readl(ctrl) & ~EEPROM_ECLK, ctrl);
- writel(readl(ctrl) | EEPROM_ECLK, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_DATO, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_ECLK, ctrl);
+ delay();
+ __raw_writel(__raw_readl(ctrl) | EEPROM_ECLK, ctrl);
+ delay();
ser_cmd <<= 1;
}
/* see data sheet timing diagram */
- writel(readl(ctrl) & ~EEPROM_DATO, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_DATO, ctrl);
}
unsigned short ip22_eeprom_read(unsigned int *ctrl, int reg)
unsigned short res = 0;
int i;
- writel(readl(ctrl) & ~EEPROM_EPROT, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_EPROT, ctrl);
eeprom_cs_on(ctrl);
eeprom_cmd(ctrl, EEPROM_READ, reg);
/* clock the data ouf of serial mem */
for (i = 0; i < 16; i++) {
- writel(readl(ctrl) & ~EEPROM_ECLK, ctrl);
+ __raw_writel(__raw_readl(ctrl) & ~EEPROM_ECLK, ctrl);
delay();
- writel(readl(ctrl) | EEPROM_ECLK, ctrl);
+ __raw_writel(__raw_readl(ctrl) | EEPROM_ECLK, ctrl);
delay();
res <<= 1;
- if (readl(ctrl) & EEPROM_DATI)
+ if (__raw_readl(ctrl) & EEPROM_DATI)
res |= 1;
}
static void enable_macepci_irq(unsigned int irq)
{
- macepci_mask |= MACEPCI_CONTROL_INT(irq - 9);
+ macepci_mask |= MACEPCI_CONTROL_INT(irq - MACEPCI_SCSI0_IRQ);
mace->pci.control = macepci_mask;
- crime_mask |= 1 << (irq - 1);
+ crime_mask |= 1 << (irq - CRIME_IRQ_BASE);
crime->imask = crime_mask;
}
static void disable_macepci_irq(unsigned int irq)
{
- crime_mask &= ~(1 << (irq - 1));
+ crime_mask &= ~(1 << (irq - CRIME_IRQ_BASE));
crime->imask = crime_mask;
flush_crime_bus();
- macepci_mask &= ~MACEPCI_CONTROL_INT(irq - 9);
+ macepci_mask &= ~MACEPCI_CONTROL_INT(irq - MACEPCI_SCSI0_IRQ);
mace->pci.control = macepci_mask;
flush_mace_bus();
}
pr_debug("crime_int %08x enabled\n", crime_int);
crime_mask |= crime_int;
crime->imask = crime_mask;
- maceisa_mask |= 1 << (irq - 33);
+ maceisa_mask |= 1 << (irq - MACEISA_AUDIO_SW_IRQ);
mace->perif.ctrl.imask = maceisa_mask;
}
{
unsigned int crime_int = 0;
- maceisa_mask &= ~(1 << (irq - 33));
+ maceisa_mask &= ~(1 << (irq - MACEISA_AUDIO_SW_IRQ));
if (!(maceisa_mask & MACEISA_AUDIO_INT))
crime_int |= MACE_AUDIO_INT;
if (!(maceisa_mask & MACEISA_MISC_INT))
case MACEISA_SERIAL2_TDMAPR_IRQ:
/* edge triggered */
mace_int = mace->perif.ctrl.istat;
- mace_int &= ~(1 << (irq - 33));
+ mace_int &= ~(1 << (irq - MACEISA_AUDIO_SW_IRQ));
mace->perif.ctrl.istat = mace_int;
break;
}
static void enable_mace_irq(unsigned int irq)
{
- crime_mask |= 1 << (irq - 1);
+ unsigned int bit = irq - CRIME_IRQ_BASE;
+
+ crime_mask |= (1 << bit);
crime->imask = crime_mask;
}
static void disable_mace_irq(unsigned int irq)
{
- crime_mask &= ~(1 << (irq - 1));
+ unsigned int bit = irq - CRIME_IRQ_BASE;
+
+ crime_mask &= ~(1 << bit);
crime->imask = crime_mask;
flush_crime_bus();
}
mace->perif.ctrl.imask = 0;
mips_cpu_irq_init();
- for (irq = MIPS_CPU_IRQ_BASE + 8; irq <= IP32_IRQ_MAX; irq++) {
+ for (irq = CRIME_IRQ_BASE; irq <= IP32_IRQ_MAX; irq++) {
switch (irq) {
case MACE_VID_IN1_IRQ ... MACE_PCI_BRIDGE_IRQ:
set_irq_chip(irq, &ip32_mace_interrupt);
config CASIO_E55
bool "CASIO CASSIOPEIA E-10/15/55/65"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select ISA
config IBM_WORKPAD
bool "IBM WorkPad z50"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select ISA
config NEC_CMBVR4133
bool "NEC CMB-VR4133"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select HW_HAS_PCI
config TANBAC_TB022X
bool "TANBAC VR4131 multichip module and TANBAC VR4131DIMM"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select HW_HAS_PCI
config VICTOR_MPC30X
bool "Victor MP-C303/304"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select HW_HAS_PCI
config ZAO_CAPCELLA
bool "ZAO Networks Capcella"
select CEVT_R4K
+ select CSRC_R4K
select DMA_NONCOHERENT
select IRQ_CPU
select HW_HAS_PCI
};
i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3000 100>;
interrupts = <e 8>;
interrupt-parent = < &ipic >;
dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <68>;
+ };
};
serial@4500 {
reg = <700 100>;
device_type = "ipic";
};
-
+
par_io@1400 {
reg = <1400 100>;
device_type = "par_io";
3 5 1 0 2 0 /* MDC */
0 d 2 0 1 0 /* RX_CLK (CLK9) */
3 18 2 0 1 0 /* TX_CLK (CLK10) */
- 1 1 1 0 1 0 /* TxD1 */
1 0 1 0 1 0 /* TxD0 */
1 1 1 0 1 0 /* TxD1 */
1 2 1 0 1 0 /* TxD2 */
reg = <e0100000 480>;
brg-frequency = <0>;
bus-frequency = <BCD3D80>;
-
+
muram@10000 {
device_type = "muram";
ranges = <0 00010000 00004000>;
-
+
data-only@0 {
reg = <0 4000>;
};
compatible = "ucc_geth";
model = "UCC";
device-id = <4>;
- reg = <3000 200>;
+ reg = <3200 200>;
interrupts = <23>;
interrupt-parent = < &qeic >;
/*
};
i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3000 100>;
interrupts = <e 8>;
interrupt-parent = < &ipic >;
dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <68>;
+ };
};
i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3100 100>;
};
i2c@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3000 100>;
interrupts = <e 8>;
interrupt-parent = < &ipic >;
dfsrr;
+
+ rtc@68 {
+ compatible = "dallas,ds1374";
+ reg = <68>;
+ };
};
i2c@3100 {
+ #address-cells = <1>;
+ #size-cells = <0>;
device_type = "i2c";
compatible = "fsl-i2c";
reg = <3100 100>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <1b 2>;
- interrupt-map-mask = <fb00 0 0 0>;
+ interrupt-map-mask = <ff00 0 0 1>;
interrupt-map = <
// IDSEL 0x1c USB
- e000 0 0 0 &i8259 c 2
- e100 0 0 0 &i8259 9 2
- e200 0 0 0 &i8259 a 2
- e300 0 0 0 &i8259 b 2
+ e000 0 0 1 &i8259 c 2
+ e100 0 0 1 &i8259 9 2
+ e200 0 0 1 &i8259 a 2
+ e300 0 0 1 &i8259 b 2
// IDSEL 0x1d Audio
- e800 0 0 0 &i8259 6 2
+ e800 0 0 1 &i8259 6 2
// IDSEL 0x1e Legacy
- f000 0 0 0 &i8259 7 2
- f100 0 0 0 &i8259 7 2
+ f000 0 0 1 &i8259 7 2
+ f100 0 0 1 &i8259 7 2
// IDSEL 0x1f IDE/SATA
- f800 0 0 0 &i8259 e 2
- f900 0 0 0 &i8259 5 2
+ f800 0 0 1 &i8259 e 2
+ f900 0 0 1 &i8259 5 2
>;
pcie@0 {
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <18 2>;
- interrupt-map-mask = <fb00 0 0 0>;
+ interrupt-map-mask = <ff00 0 0 7>;
interrupt-map = <
- /* IDSEL 0x11 - PCI slot 1 */
+ /* IDSEL 0x11 func 0 - PCI slot 1 */
8800 0 0 1 &mpic 2 1
8800 0 0 2 &mpic 3 1
8800 0 0 3 &mpic 4 1
8800 0 0 4 &mpic 1 1
- /* IDSEL 0x12 - PCI slot 2 */
+ /* IDSEL 0x11 func 1 - PCI slot 1 */
+ 8900 0 0 1 &mpic 2 1
+ 8900 0 0 2 &mpic 3 1
+ 8900 0 0 3 &mpic 4 1
+ 8900 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 2 - PCI slot 1 */
+ 8a00 0 0 1 &mpic 2 1
+ 8a00 0 0 2 &mpic 3 1
+ 8a00 0 0 3 &mpic 4 1
+ 8a00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 3 - PCI slot 1 */
+ 8b00 0 0 1 &mpic 2 1
+ 8b00 0 0 2 &mpic 3 1
+ 8b00 0 0 3 &mpic 4 1
+ 8b00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 4 - PCI slot 1 */
+ 8c00 0 0 1 &mpic 2 1
+ 8c00 0 0 2 &mpic 3 1
+ 8c00 0 0 3 &mpic 4 1
+ 8c00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 5 - PCI slot 1 */
+ 8d00 0 0 1 &mpic 2 1
+ 8d00 0 0 2 &mpic 3 1
+ 8d00 0 0 3 &mpic 4 1
+ 8d00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 6 - PCI slot 1 */
+ 8e00 0 0 1 &mpic 2 1
+ 8e00 0 0 2 &mpic 3 1
+ 8e00 0 0 3 &mpic 4 1
+ 8e00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 7 - PCI slot 1 */
+ 8f00 0 0 1 &mpic 2 1
+ 8f00 0 0 2 &mpic 3 1
+ 8f00 0 0 3 &mpic 4 1
+ 8f00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x12 func 0 - PCI slot 2 */
9000 0 0 1 &mpic 3 1
9000 0 0 2 &mpic 4 1
9000 0 0 3 &mpic 1 1
9000 0 0 4 &mpic 2 1
+ /* IDSEL 0x12 func 1 - PCI slot 2 */
+ 9100 0 0 1 &mpic 3 1
+ 9100 0 0 2 &mpic 4 1
+ 9100 0 0 3 &mpic 1 1
+ 9100 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 2 - PCI slot 2 */
+ 9200 0 0 1 &mpic 3 1
+ 9200 0 0 2 &mpic 4 1
+ 9200 0 0 3 &mpic 1 1
+ 9200 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 3 - PCI slot 2 */
+ 9300 0 0 1 &mpic 3 1
+ 9300 0 0 2 &mpic 4 1
+ 9300 0 0 3 &mpic 1 1
+ 9300 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 4 - PCI slot 2 */
+ 9400 0 0 1 &mpic 3 1
+ 9400 0 0 2 &mpic 4 1
+ 9400 0 0 3 &mpic 1 1
+ 9400 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 5 - PCI slot 2 */
+ 9500 0 0 1 &mpic 3 1
+ 9500 0 0 2 &mpic 4 1
+ 9500 0 0 3 &mpic 1 1
+ 9500 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 6 - PCI slot 2 */
+ 9600 0 0 1 &mpic 3 1
+ 9600 0 0 2 &mpic 4 1
+ 9600 0 0 3 &mpic 1 1
+ 9600 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 7 - PCI slot 2 */
+ 9700 0 0 1 &mpic 3 1
+ 9700 0 0 2 &mpic 4 1
+ 9700 0 0 3 &mpic 1 1
+ 9700 0 0 4 &mpic 2 1
+
// IDSEL 0x1c USB
- e000 0 0 0 &i8259 c 2
- e100 0 0 0 &i8259 9 2
- e200 0 0 0 &i8259 a 2
- e300 0 0 0 &i8259 b 2
+ e000 0 0 1 &i8259 c 2
+ e100 0 0 1 &i8259 9 2
+ e200 0 0 1 &i8259 a 2
+ e300 0 0 1 &i8259 b 2
// IDSEL 0x1d Audio
- e800 0 0 0 &i8259 6 2
+ e800 0 0 1 &i8259 6 2
// IDSEL 0x1e Legacy
- f000 0 0 0 &i8259 7 2
- f100 0 0 0 &i8259 7 2
+ f000 0 0 1 &i8259 7 2
+ f100 0 0 1 &i8259 7 2
// IDSEL 0x1f IDE/SATA
- f800 0 0 0 &i8259 e 2
- f900 0 0 0 &i8259 5 2
+ f800 0 0 1 &i8259 e 2
+ f900 0 0 1 &i8259 5 2
>;
clock-frequency = <1fca055>;
interrupt-parent = <&mpic>;
interrupts = <18 2>;
- interrupt-map-mask = <fb00 0 0 0>;
+ interrupt-map-mask = <ff00 0 0 7>;
interrupt-map = <
- /* IDSEL 0x11 */
- 8800 0 0 1 &i8259 9 2
- 8800 0 0 2 &i8259 a 2
- 8800 0 0 3 &i8259 b 2
- 8800 0 0 4 &i8259 c 2
-
- /* IDSEL 0x12 */
- 9000 0 0 1 &i8259 a 2
- 9000 0 0 2 &i8259 b 2
- 9000 0 0 3 &i8259 c 2
- 9000 0 0 4 &i8259 9 2
+ /* IDSEL 0x11 func 0 - PCI slot 1 */
+ 8800 0 0 1 &mpic 2 1
+ 8800 0 0 2 &mpic 3 1
+ 8800 0 0 3 &mpic 4 1
+ 8800 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 1 - PCI slot 1 */
+ 8900 0 0 1 &mpic 2 1
+ 8900 0 0 2 &mpic 3 1
+ 8900 0 0 3 &mpic 4 1
+ 8900 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 2 - PCI slot 1 */
+ 8a00 0 0 1 &mpic 2 1
+ 8a00 0 0 2 &mpic 3 1
+ 8a00 0 0 3 &mpic 4 1
+ 8a00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 3 - PCI slot 1 */
+ 8b00 0 0 1 &mpic 2 1
+ 8b00 0 0 2 &mpic 3 1
+ 8b00 0 0 3 &mpic 4 1
+ 8b00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 4 - PCI slot 1 */
+ 8c00 0 0 1 &mpic 2 1
+ 8c00 0 0 2 &mpic 3 1
+ 8c00 0 0 3 &mpic 4 1
+ 8c00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 5 - PCI slot 1 */
+ 8d00 0 0 1 &mpic 2 1
+ 8d00 0 0 2 &mpic 3 1
+ 8d00 0 0 3 &mpic 4 1
+ 8d00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 6 - PCI slot 1 */
+ 8e00 0 0 1 &mpic 2 1
+ 8e00 0 0 2 &mpic 3 1
+ 8e00 0 0 3 &mpic 4 1
+ 8e00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x11 func 7 - PCI slot 1 */
+ 8f00 0 0 1 &mpic 2 1
+ 8f00 0 0 2 &mpic 3 1
+ 8f00 0 0 3 &mpic 4 1
+ 8f00 0 0 4 &mpic 1 1
+
+ /* IDSEL 0x12 func 0 - PCI slot 2 */
+ 9000 0 0 1 &mpic 3 1
+ 9000 0 0 2 &mpic 4 1
+ 9000 0 0 3 &mpic 1 1
+ 9000 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 1 - PCI slot 2 */
+ 9100 0 0 1 &mpic 3 1
+ 9100 0 0 2 &mpic 4 1
+ 9100 0 0 3 &mpic 1 1
+ 9100 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 2 - PCI slot 2 */
+ 9200 0 0 1 &mpic 3 1
+ 9200 0 0 2 &mpic 4 1
+ 9200 0 0 3 &mpic 1 1
+ 9200 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 3 - PCI slot 2 */
+ 9300 0 0 1 &mpic 3 1
+ 9300 0 0 2 &mpic 4 1
+ 9300 0 0 3 &mpic 1 1
+ 9300 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 4 - PCI slot 2 */
+ 9400 0 0 1 &mpic 3 1
+ 9400 0 0 2 &mpic 4 1
+ 9400 0 0 3 &mpic 1 1
+ 9400 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 5 - PCI slot 2 */
+ 9500 0 0 1 &mpic 3 1
+ 9500 0 0 2 &mpic 4 1
+ 9500 0 0 3 &mpic 1 1
+ 9500 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 6 - PCI slot 2 */
+ 9600 0 0 1 &mpic 3 1
+ 9600 0 0 2 &mpic 4 1
+ 9600 0 0 3 &mpic 1 1
+ 9600 0 0 4 &mpic 2 1
+
+ /* IDSEL 0x12 func 7 - PCI slot 2 */
+ 9700 0 0 1 &mpic 3 1
+ 9700 0 0 2 &mpic 4 1
+ 9700 0 0 3 &mpic 1 1
+ 9700 0 0 4 &mpic 2 1
// IDSEL 0x1c USB
- e000 0 0 0 &i8259 c 2
- e100 0 0 0 &i8259 9 2
- e200 0 0 0 &i8259 a 2
- e300 0 0 0 &i8259 b 2
+ e000 0 0 1 &i8259 c 2
+ e100 0 0 1 &i8259 9 2
+ e200 0 0 1 &i8259 a 2
+ e300 0 0 1 &i8259 b 2
// IDSEL 0x1d Audio
- e800 0 0 0 &i8259 6 2
+ e800 0 0 1 &i8259 6 2
// IDSEL 0x1e Legacy
- f000 0 0 0 &i8259 7 2
- f100 0 0 0 &i8259 7 2
+ f000 0 0 1 &i8259 7 2
+ f100 0 0 1 &i8259 7 2
// IDSEL 0x1f IDE/SATA
- f800 0 0 0 &i8259 e 2
- f900 0 0 0 &i8259 5 2
+ f800 0 0 1 &i8259 e 2
+ f900 0 0 1 &i8259 5 2
>;
pcie@0 {
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1374=y
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
#
# DMA Engine support
#
# SPI support
#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
+CONFIG_SPI=y
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_MPC83xx=y
+
+#
+# SPI Protocol Masters
+#
+# CONFIG_SPI_AT25 is not set
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM70 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
-# CONFIG_MMC is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+# CONFIG_SDIO_UART is not set
+
+#
+# MMC/SD Host Controller Drivers
+#
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_WBSD is not set
+# CONFIG_MMC_TIFM_SD is not set
+CONFIG_MMC_SPI=y
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC_ITU_T=y
CONFIG_CRC32=y
-# CONFIG_CRC7 is not set
+CONFIG_CRC7=y
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_USB_EHCI_FSL=y
# CONFIG_USB_ISP116X_HCD is not set
# CONFIG_USB_OHCI_HCD is not set
-# CONFIG_USB_UHCI_HCD is not set
+CONFIG_USB_UHCI_HCD=y
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
-# CONFIG_USB is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+# CONFIG_USB_DEVICEFS is not set
+CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+CONFIG_USB_EHCI_HCD=y
+# CONFIG_USB_EHCI_SPLIT_ISO is not set
CONFIG_USB_EHCI_ROOT_HUB_TT=y
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
CONFIG_USB_EHCI_FSL=y
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_OHCI_HCD is not set
+CONFIG_USB_UHCI_HCD=y
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=y
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+
+#
+# USB DSL modem support
+#
+
#
# USB Gadget Support
#
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1374=y
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
#
# DMA Engine support
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1374=y
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
#
# DMA Engine support
# CONFIG_NEW_LEDS is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
-# CONFIG_RTC_CLASS is not set
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1374=y
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
+#
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
#
# DMA Engine support
DEFINE(CFG_SYSCALL_MAP32, offsetof(struct vdso_data, syscall_map_32));
DEFINE(WTOM_CLOCK_SEC, offsetof(struct vdso_data, wtom_clock_sec));
DEFINE(WTOM_CLOCK_NSEC, offsetof(struct vdso_data, wtom_clock_nsec));
+ DEFINE(CFG_ICACHE_BLOCKSZ, offsetof(struct vdso_data, icache_block_size));
+ DEFINE(CFG_DCACHE_BLOCKSZ, offsetof(struct vdso_data, dcache_block_size));
+ DEFINE(CFG_ICACHE_LOGBLOCKSZ, offsetof(struct vdso_data, icache_log_block_size));
+ DEFINE(CFG_DCACHE_LOGBLOCKSZ, offsetof(struct vdso_data, dcache_log_block_size));
#ifdef CONFIG_PPC64
DEFINE(CFG_SYSCALL_MAP64, offsetof(struct vdso_data, syscall_map_64));
DEFINE(TVAL64_TV_SEC, offsetof(struct timeval, tv_sec));
#include <linux/init.h>
#include <linux/capability.h>
#include <linux/delay.h>
+#include <linux/smp.h>
+#include <linux/completion.h>
+#include <linux/cpumask.h>
#include <asm/prom.h>
#include <asm/rtas.h>
#include <asm/lmb.h>
#include <asm/udbg.h>
#include <asm/syscalls.h>
+#include <asm/smp.h>
+#include <asm/atomic.h>
struct rtas_t rtas = {
.lock = SPIN_LOCK_UNLOCKED
EXPORT_SYMBOL(rtas);
struct rtas_suspend_me_data {
- long waiting;
- struct rtas_args *args;
+ atomic_t working; /* number of cpus accessing this struct */
+ int token; /* ibm,suspend-me */
+ int error;
+ struct completion *complete; /* wait on this until working == 0 */
};
DEFINE_SPINLOCK(rtas_data_buf_lock);
/* Must be in the RMO region, so we place it here */
static char rtas_os_term_buf[2048];
-void rtas_os_term(char *str)
+void rtas_panic_msg(char *str)
{
- int status;
+ snprintf(rtas_os_term_buf, 2048, "OS panic: %s", str);
+}
- if (panic_timeout)
- return;
+void rtas_os_term(void)
+{
+ int status;
if (RTAS_UNKNOWN_SERVICE == rtas_token("ibm,os-term"))
return;
- snprintf(rtas_os_term_buf, 2048, "OS panic: %s", str);
-
do {
status = rtas_call(rtas_token("ibm,os-term"), 1, 1, NULL,
__pa(rtas_os_term_buf));
#ifdef CONFIG_PPC_PSERIES
static void rtas_percpu_suspend_me(void *info)
{
- int i;
long rc;
- long flags;
+ unsigned long msr_save;
+ int cpu;
struct rtas_suspend_me_data *data =
(struct rtas_suspend_me_data *)info;
- /*
- * We use "waiting" to indicate our state. As long
- * as it is >0, we are still trying to all join up.
- * If it goes to 0, we have successfully joined up and
- * one thread got H_CONTINUE. If any error happens,
- * we set it to <0.
- */
- local_irq_save(flags);
- do {
- rc = plpar_hcall_norets(H_JOIN);
- smp_rmb();
- } while (rc == H_SUCCESS && data->waiting > 0);
- if (rc == H_SUCCESS)
- goto out;
+ atomic_inc(&data->working);
+
+ /* really need to ensure MSR.EE is off for H_JOIN */
+ msr_save = mfmsr();
+ mtmsr(msr_save & ~(MSR_EE));
+
+ rc = plpar_hcall_norets(H_JOIN);
- if (rc == H_CONTINUE) {
- data->waiting = 0;
- data->args->args[data->args->nargs] =
- rtas_call(ibm_suspend_me_token, 0, 1, NULL);
- for_each_possible_cpu(i)
- plpar_hcall_norets(H_PROD,i);
+ mtmsr(msr_save);
+
+ if (rc == H_SUCCESS) {
+ /* This cpu was prodded and the suspend is complete. */
+ goto out;
+ } else if (rc == H_CONTINUE) {
+ /* All other cpus are in H_JOIN, this cpu does
+ * the suspend.
+ */
+ printk(KERN_DEBUG "calling ibm,suspend-me on cpu %i\n",
+ smp_processor_id());
+ data->error = rtas_call(data->token, 0, 1, NULL);
+
+ if (data->error)
+ printk(KERN_DEBUG "ibm,suspend-me returned %d\n",
+ data->error);
} else {
- data->waiting = -EBUSY;
- printk(KERN_ERR "Error on H_JOIN hypervisor call\n");
+ printk(KERN_ERR "H_JOIN on cpu %i failed with rc = %ld\n",
+ smp_processor_id(), rc);
+ data->error = rc;
}
-
+ /* This cpu did the suspend or got an error; in either case,
+ * we need to prod all other other cpus out of join state.
+ * Extra prods are harmless.
+ */
+ for_each_online_cpu(cpu)
+ plpar_hcall_norets(H_PROD, get_hard_smp_processor_id(cpu));
out:
- local_irq_restore(flags);
- return;
+ if (atomic_dec_return(&data->working) == 0)
+ complete(data->complete);
}
static int rtas_ibm_suspend_me(struct rtas_args *args)
{
- int i;
long state;
long rc;
unsigned long retbuf[PLPAR_HCALL_BUFSIZE];
struct rtas_suspend_me_data data;
+ DECLARE_COMPLETION_ONSTACK(done);
+
+ if (!rtas_service_present("ibm,suspend-me"))
+ return -ENOSYS;
/* Make sure the state is valid */
rc = plpar_hcall(H_VASI_STATE, retbuf,
return 0;
}
- data.waiting = 1;
- data.args = args;
+ atomic_set(&data.working, 0);
+ data.token = rtas_token("ibm,suspend-me");
+ data.error = 0;
+ data.complete = &done;
/* Call function on all CPUs. One of us will make the
* rtas call
*/
if (on_each_cpu(rtas_percpu_suspend_me, &data, 1, 0))
- data.waiting = -EINVAL;
+ data.error = -EINVAL;
- if (data.waiting != 0)
- printk(KERN_ERR "Error doing global join\n");
+ wait_for_completion(&done);
- /* Prod each CPU. This won't hurt, and will wake
- * anyone we successfully put to sleep with H_JOIN.
- */
- for_each_possible_cpu(i)
- plpar_hcall_norets(H_PROD, i);
+ if (data.error != 0)
+ printk(KERN_ERR "Error doing global join\n");
- return data.waiting;
+ return data.error;
}
#else /* CONFIG_PPC_PSERIES */
static int rtas_ibm_suspend_me(struct rtas_args *args)
/* deltascaled includes both user and system time.
* Hence scale it based on the purr ratio to estimate
* the system time */
- deltascaled = deltascaled * get_paca()->system_time /
- (get_paca()->system_time + get_paca()->user_time);
+ if (get_paca()->user_time)
+ deltascaled = deltascaled * get_paca()->system_time /
+ (get_paca()->system_time + get_paca()->user_time);
delta += get_paca()->system_time;
get_paca()->system_time = 0;
}
vdso_data->icache_size = ppc64_caches.isize;
vdso_data->icache_line_size = ppc64_caches.iline_size;
+ /* XXXOJN: Blocks should be added to ppc64_caches and used instead */
+ vdso_data->dcache_block_size = ppc64_caches.dline_size;
+ vdso_data->icache_block_size = ppc64_caches.iline_size;
+ vdso_data->dcache_log_block_size = ppc64_caches.log_dline_size;
+ vdso_data->icache_log_block_size = ppc64_caches.log_iline_size;
+
/*
* Calculate the size of the 64 bits vDSO
*/
vdso64_pages = (&vdso64_end - &vdso64_start) >> PAGE_SHIFT;
DBG("vdso64_kbase: %p, 0x%x pages\n", vdso64_kbase, vdso64_pages);
+#else
+ vdso_data->dcache_block_size = L1_CACHE_BYTES;
+ vdso_data->dcache_log_block_size = L1_CACHE_SHIFT;
+ vdso_data->icache_block_size = L1_CACHE_BYTES;
+ vdso_data->icache_log_block_size = L1_CACHE_SHIFT;
#endif /* CONFIG_PPC64 */
*
* Flushes the data cache & invalidate the instruction cache for the
* provided range [start, end[
- *
- * Note: all CPUs supported by this kernel have a 128 bytes cache
- * line size so we don't have to peek that info from the datapage
*/
V_FUNCTION_BEGIN(__kernel_sync_dicache)
.cfi_startproc
- li r5,127
- andc r6,r3,r5 /* round low to line bdy */
+ mflr r12
+ .cfi_register lr,r12
+ mr r11,r3
+ bl __get_datapage@local
+ mtlr r12
+ mr r10,r3
+
+ lwz r7,CFG_DCACHE_BLOCKSZ(r10)
+ addi r5,r7,-1
+ andc r6,r11,r5 /* round low to line bdy */
subf r8,r6,r4 /* compute length */
add r8,r8,r5 /* ensure we get enough */
- srwi. r8,r8,7 /* compute line count */
+ lwz r9,CFG_DCACHE_LOGBLOCKSZ(r10)
+ srw. r8,r8,r9 /* compute line count */
crclr cr0*4+so
beqlr /* nothing to do? */
mtctr r8
- mr r3,r6
-1: dcbst 0,r3
- addi r3,r3,128
+1: dcbst 0,r6
+ add r6,r6,r7
bdnz 1b
sync
+
+/* Now invalidate the instruction cache */
+
+ lwz r7,CFG_ICACHE_BLOCKSZ(r10)
+ addi r5,r7,-1
+ andc r6,r11,r5 /* round low to line bdy */
+ subf r8,r6,r4 /* compute length */
+ add r8,r8,r5
+ lwz r9,CFG_ICACHE_LOGBLOCKSZ(r10)
+ srw. r8,r8,r9 /* compute line count */
+ crclr cr0*4+so
+ beqlr /* nothing to do? */
mtctr r8
-1: icbi 0,r6
- addi r6,r6,128
- bdnz 1b
+2: icbi 0,r6
+ add r6,r6,r7
+ bdnz 2b
isync
li r3,0
blr
*
* Flushes the data cache & invalidate the instruction cache for the
* provided range [start, end[
- *
- * Note: all CPUs supported by this kernel have a 128 bytes cache
- * line size so we don't have to peek that info from the datapage
*/
V_FUNCTION_BEGIN(__kernel_sync_dicache)
.cfi_startproc
- li r5,127
- andc r6,r3,r5 /* round low to line bdy */
+ mflr r12
+ .cfi_register lr,r12
+ mr r11,r3
+ bl V_LOCAL_FUNC(__get_datapage)
+ mtlr r12
+ mr r10,r3
+
+ lwz r7,CFG_DCACHE_BLOCKSZ(r10)
+ addi r5,r7,-1
+ andc r6,r11,r5 /* round low to line bdy */
subf r8,r6,r4 /* compute length */
add r8,r8,r5 /* ensure we get enough */
- srwi. r8,r8,7 /* compute line count */
+ lwz r9,CFG_DCACHE_LOGBLOCKSZ(r10)
+ srw. r8,r8,r9 /* compute line count */
crclr cr0*4+so
beqlr /* nothing to do? */
mtctr r8
- mr r3,r6
-1: dcbst 0,r3
- addi r3,r3,128
+1: dcbst 0,r6
+ add r6,r6,r7
bdnz 1b
sync
+
+/* Now invalidate the instruction cache */
+
+ lwz r7,CFG_ICACHE_BLOCKSZ(r10)
+ addi r5,r7,-1
+ andc r6,r11,r5 /* round low to line bdy */
+ subf r8,r6,r4 /* compute length */
+ add r8,r8,r5
+ lwz r9,CFG_ICACHE_LOGBLOCKSZ(r10)
+ srw. r8,r8,r9 /* compute line count */
+ crclr cr0*4+so
+ beqlr /* nothing to do? */
mtctr r8
-1: icbi 0,r6
- addi r6,r6,128
- bdnz 1b
+2: icbi 0,r6
+ add r6,r6,r7
+ bdnz 2b
isync
li r3,0
blr
* we invalidate the TLB here, thus avoiding dcbst
* misbehaviour.
*/
- _tlbie(address);
+ _tlbie(address, 0 /* 8xx doesn't care about PID */);
#endif
if (!PageReserved(page)
&& !test_bit(PG_arch_1, &page->flags)) {
* architectures. -- Dan
*/
#if defined(CONFIG_8xx)
-#define flush_HPTE(X, va, pg) _tlbie(va)
+#define flush_HPTE(X, va, pg) _tlbie(va, 0 /* 8xx doesn't care about PID */)
#define MMU_init_hw() do { } while(0)
#define mmu_mapin_ram() (0UL)
#include <asm/lmb.h>
#include <asm/abs_addr.h>
#include <asm/firmware.h>
+#include <asm/iseries/hv_call.h>
struct stab_entry {
unsigned long esid_data;
*/
#include <linux/init.h>
+#include <linux/of_platform.h>
+
#include <asm/machdep.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/time.h>
#include <asm/uic.h>
-#include <asm/of_platform.h>
static struct of_device_id walnut_of_bus[] = {
{ .compatible = "ibm,plb3", },
* option) any later version.
*/
#include <linux/init.h>
+#include <linux/of_platform.h>
+
#include <asm/machdep.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/time.h>
#include <asm/uic.h>
-#include <asm/of_platform.h>
#include "44x.h"
static struct of_device_id bamboo_of_bus[] = {
*/
#include <linux/init.h>
+#include <linux/of_platform.h>
+
#include <asm/machdep.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/time.h>
#include <asm/uic.h>
-#include <asm/of_platform.h>
#include "44x.h"
* option) any later version.
*/
#include <linux/init.h>
+#include <linux/of_platform.h>
+
#include <asm/machdep.h>
#include <asm/prom.h>
#include <asm/udbg.h>
#include <asm/time.h>
#include <asm/uic.h>
-#include <asm/of_platform.h>
#include "44x.h"
static struct of_device_id sequoia_of_bus[] = {
if ((np = of_find_compatible_node(NULL, "network", "ucc_geth"))
!= NULL){
- /* Reset the Ethernet PHY */
- bcsr_regs[9] &= ~0x20;
+ /* Reset the Ethernet PHYs */
+#define BCSR8_FETH_RST 0x50
+ bcsr_regs[8] &= ~BCSR8_FETH_RST;
udelay(1000);
- bcsr_regs[9] |= 0x20;
+ bcsr_regs[8] |= BCSR8_FETH_RST;
iounmap(bcsr_regs);
of_node_put(np);
}
#endif /* CONFIG_QUICC_ENGINE */
}
-#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374)
-extern ulong ds1374_get_rtc_time(void);
-extern int ds1374_set_rtc_time(ulong);
-
-static int __init mpc832x_rtc_hookup(void)
-{
- struct timespec tv;
-
- if (!machine_is(mpc832x_mds))
- return 0;
-
- ppc_md.get_rtc_time = ds1374_get_rtc_time;
- ppc_md.set_rtc_time = ds1374_set_rtc_time;
-
- tv.tv_nsec = 0;
- tv.tv_sec = (ppc_md.get_rtc_time) ();
- do_settimeofday(&tv);
-
- return 0;
-}
-
-late_initcall(mpc832x_rtc_hookup);
-#endif
-
/*
* Called very early, MMU is off, device-tree isn't unflattened
*/
*/
#include <linux/pci.h>
+#include <linux/interrupt.h>
#include <linux/spi/spi.h>
+#include <linux/spi/mmc_spi.h>
+#include <linux/mmc/host.h>
#include <asm/of_platform.h>
#include <asm/time.h>
par_io_data_set(3, 13, !polarity);
}
+static struct mmc_spi_platform_data mpc832x_mmc_pdata = {
+ .ocr_mask = MMC_VDD_33_34,
+};
+
static struct spi_board_info mpc832x_spi_boardinfo = {
.bus_num = 0x4c0,
.chip_select = 0,
.max_speed_hz = 50000000,
- /*
- * XXX: This is spidev (spi in userspace) stub, should
- * be replaced by "mmc_spi" when mmc_spi will hit mainline.
- */
- .modalias = "spidev",
+ .modalias = "mmc_spi",
+ .platform_data = &mpc832x_mmc_pdata,
};
static int __init mpc832x_spi_init(void)
ipic_set_default_priority();
}
-#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374)
-extern ulong ds1374_get_rtc_time(void);
-extern int ds1374_set_rtc_time(ulong);
-
-static int __init mpc834x_rtc_hookup(void)
-{
- struct timespec tv;
-
- if (!machine_is(mpc834x_mds))
- return 0;
-
- ppc_md.get_rtc_time = ds1374_get_rtc_time;
- ppc_md.set_rtc_time = ds1374_set_rtc_time;
-
- tv.tv_nsec = 0;
- tv.tv_sec = (ppc_md.get_rtc_time) ();
- do_settimeofday(&tv);
-
- return 0;
-}
-
-late_initcall(mpc834x_rtc_hookup);
-#endif
-
/*
* Called very early, MMU is off, device-tree isn't unflattened
*/
if ((np = of_find_compatible_node(NULL, "network", "ucc_geth"))
!= NULL){
+ uint svid;
+
/* Reset the Ethernet PHY */
- bcsr_regs[9] &= ~0x20;
+#define BCSR9_GETHRST 0x20
+ clrbits8(&bcsr_regs[9], BCSR9_GETHRST);
udelay(1000);
- bcsr_regs[9] |= 0x20;
+ setbits8(&bcsr_regs[9], BCSR9_GETHRST);
+
+ /* handle mpc8360ea rev.2.1 erratum 2: RGMII Timing */
+ svid = mfspr(SPRN_SVR);
+ if (svid == 0x80480021) {
+ void __iomem *immap;
+
+ immap = ioremap(get_immrbase() + 0x14a8, 8);
+
+ /*
+ * IMMR + 0x14A8[4:5] = 11 (clk delay for UCC 2)
+ * IMMR + 0x14A8[18:19] = 11 (clk delay for UCC 1)
+ */
+ setbits32(immap, 0x0c003000);
+
+ /*
+ * IMMR + 0x14AC[20:27] = 10101010
+ * (data delay for both UCC's)
+ */
+ clrsetbits_be32(immap + 4, 0xff0, 0xaa0);
+
+ iounmap(immap);
+ }
+
iounmap(bcsr_regs);
of_node_put(np);
}
-
#endif /* CONFIG_QUICC_ENGINE */
}
#endif /* CONFIG_QUICC_ENGINE */
}
-#if defined(CONFIG_I2C_MPC) && defined(CONFIG_SENSORS_DS1374)
-extern ulong ds1374_get_rtc_time(void);
-extern int ds1374_set_rtc_time(ulong);
-
-static int __init mpc8360_rtc_hookup(void)
-{
- struct timespec tv;
-
- if (!machine_is(mpc836x_mds))
- return 0;
-
- ppc_md.get_rtc_time = ds1374_get_rtc_time;
- ppc_md.set_rtc_time = ds1374_set_rtc_time;
-
- tv.tv_nsec = 0;
- tv.tv_sec = (ppc_md.get_rtc_time) ();
- do_settimeofday(&tv);
-
- return 0;
-}
-
-late_initcall(mpc8360_rtc_hookup);
-#endif
-
/*
* Called very early, MMU is off, device-tree isn't unflattened
*/
out_be32(immap + MPC83XX_SCCR_OFFS, temp);
/* Configure pin mux for ULPI. There is no pin mux for UTMI */
- if (!strcmp(prop, "ulpi")) {
+ if (prop && !strcmp(prop, "ulpi")) {
temp = in_be32(immap + MPC83XX_SICRL_OFFS);
temp &= ~MPC831X_SICRL_USB_MASK;
temp |= MPC831X_SICRL_USB_ULPI;
usb_regs = ioremap(res.start, res.end - res.start + 1);
/* Using on-chip PHY */
- if (!strcmp(prop, "utmi_wide") ||
- !strcmp(prop, "utmi")) {
+ if (prop && (!strcmp(prop, "utmi_wide") ||
+ !strcmp(prop, "utmi"))) {
/* Set UTMI_PHY_EN, REFSEL to 48MHZ */
out_be32(usb_regs + FSL_USB2_CONTROL_OFFS,
CONTROL_UTMI_PHY_EN | CONTROL_REFSEL_48MHZ);
/* Using external UPLI PHY */
- } else if (!strcmp(prop, "ulpi")) {
+ } else if (prop && !strcmp(prop, "ulpi")) {
/* Set PHY_CLK_SEL to ULPI */
temp = CONTROL_PHY_CLK_SEL_ULPI;
#ifdef CONFIG_USB_OTG
{
/* remove all entries */
spufs_prune_dir(dir);
+ d_drop(dir);
return simple_rmdir(parent, dir);
}
strncpy(prpmc2800_platform_name, m,
min((int)len, PLATFORM_NAME_MAX - 1));
+ _set_L2CR(_get_L2CR() | L2CR_L2E);
return 1;
}
printk(KERN_DEBUG "OpenPIC addr: %lx\n", openpic_addr);
mpic = mpic_alloc(mpic_node, openpic_addr,
- MPIC_PRIMARY|MPIC_LARGE_VECTORS|MPIC_WANTS_RESET,
+ MPIC_PRIMARY|MPIC_LARGE_VECTORS,
0, 0, " PAS-OPIC ");
BUG_ON(!mpic);
config EEH
bool "PCI Extended Error Handling (EEH)" if EMBEDDED
- depends on PPC_PSERIES
+ depends on PPC_PSERIES && PCI
default y if !EMBEDDED
config SCANLOG
.restart = rtas_restart,
.power_off = pSeries_power_off,
.halt = rtas_halt,
- .panic = rtas_os_term,
+ .panic = rtas_panic_msg,
+ .machine_shutdown = rtas_os_term,
.get_boot_time = rtas_get_boot_time,
.get_rtc_time = rtas_get_rtc_time,
.set_rtc_time = rtas_set_rtc_time,
spin_unlock_irqrestore(&uic->lock, flags);
}
+static void uic_mask_ack_irq(unsigned int virq)
+{
+ struct uic *uic = get_irq_chip_data(virq);
+ unsigned int src = uic_irq_to_hw(virq);
+ unsigned long flags;
+ u32 er, sr;
+
+ sr = 1 << (31-src);
+ spin_lock_irqsave(&uic->lock, flags);
+ er = mfdcr(uic->dcrbase + UIC_ER);
+ er &= ~sr;
+ mtdcr(uic->dcrbase + UIC_ER, er);
+ mtdcr(uic->dcrbase + UIC_SR, sr);
+ spin_unlock_irqrestore(&uic->lock, flags);
+}
+
static int uic_set_irq_type(unsigned int virq, unsigned int flow_type)
{
struct uic *uic = get_irq_chip_data(virq);
.typename = " UIC ",
.unmask = uic_unmask_irq,
.mask = uic_mask_irq,
-/* .mask_ack = uic_mask_irq_and_ack, */
+ .mask_ack = uic_mask_ack_irq,
.ack = uic_ack_irq,
.set_type = uic_set_irq_type,
};
* Identify the CPU type and fix up code sections
* that depend on which cpu we have.
*/
+#if defined(CONFIG_440EP) && defined(CONFIG_PPC_FPU)
+ /* We pass the virtual PVR here for 440EP as 440EP and 440GR have
+ * identical PVRs and there is no reliable way to check for the FPU
+ */
+ spec = identify_cpu(offset, (mfspr(SPRN_PVR) | 0x8));
+#else
spec = identify_cpu(offset, mfspr(SPRN_PVR));
+#endif
do_feature_fixups(spec->cpu_features,
PTRRELOC(&__start___ftr_fixup),
PTRRELOC(&__stop___ftr_fixup));
* That means the zeroed TLB has to be invalidated
* whenever a page miss occurs.
*/
- _tlbie(address);
+ _tlbie(address, 0 /* 8xx doesn't care about PID */);
#endif
if (!PageReserved(page)
&& !test_bit(PG_arch_1, &page->flags)) {
* architectures. -- Dan
*/
#if defined(CONFIG_8xx)
-#define flush_HPTE(X, va, pg) _tlbie(va)
+#define flush_HPTE(X, va, pg) _tlbie(va, 0 /* 8xx doesn't care about PID */)
#define MMU_init_hw() do { } while(0)
#define mmu_mapin_ram() (0UL)
break;
default:
+ iounmap(pcie_reg_fpga_base);
return;
}
}, \
}
+#define XPAR_AC97_CONTROLLER_REFERENCE(num) { \
+ .name = "ml403_ac97cr", \
+ .id = num, \
+ .num_resources = 3, \
+ .resource = (struct resource[]) { \
+ { \
+ .start = XPAR_OPB_AC97_CONTROLLER_REF_##num##_BASEADDR, \
+ .end = XPAR_OPB_AC97_CONTROLLER_REF_##num##_HIGHADDR, \
+ .flags = IORESOURCE_MEM, \
+ }, \
+ { \
+ .start = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_PLAYBACK_INTERRUPT_INTR, \
+ .end = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_PLAYBACK_INTERRUPT_INTR, \
+ .flags = IORESOURCE_IRQ, \
+ }, \
+ { \
+ .start = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_RECORD_INTERRUPT_INTR, \
+ .end = XPAR_OPB_INTC_0_OPB_AC97_CONTROLLER_REF_##num##_RECORD_INTERRUPT_INTR, \
+ .flags = IORESOURCE_IRQ, \
+ }, \
+ }, \
+}
+
/* UART 8250 driver platform data table */
struct plat_serial8250_port virtex_serial_platform_data[] = {
#if defined(XPAR_UARTNS550_0_BASEADDR)
#if defined(XPAR_TFT_3_BASEADDR)
XPAR_TFT(3),
#endif
+
+ /* AC97 Controller Reference instances */
+#if defined(XPAR_OPB_AC97_CONTROLLER_REF_0_BASEADDR)
+ XPAR_AC97_CONTROLLER_REFERENCE(0),
+#endif
+#if defined(XPAR_OPB_AC97_CONTROLLER_REF_1_BASEADDR)
+ XPAR_AC97_CONTROLLER_REFERENCE(1),
+#endif
};
/* Early serial support functions */
int active; /* monitoring status */
/* fill in from here */
- unsigned int ctl_nr; /* sysctl ID */
char name[APPLDATA_PROC_NAME_LENGTH]; /* name of /proc fs node */
unsigned char record_nr; /* Record Nr. for Product ID */
void (*callback)(void *data); /* callback function */
static struct ctl_table_header *appldata_sysctl_header;
static struct ctl_table appldata_table[] = {
{
- .ctl_name = CTL_APPLDATA_TIMER,
.procname = "timer",
.mode = S_IRUGO | S_IWUSR,
.proc_handler = &appldata_timer_handler,
},
{
- .ctl_name = CTL_APPLDATA_INTERVAL,
.procname = "interval",
.mode = S_IRUGO | S_IWUSR,
.proc_handler = &appldata_interval_handler,
},
- { .ctl_name = 0 }
+ { },
};
static struct ctl_table appldata_dir_table[] = {
{
- .ctl_name = CTL_APPLDATA,
.procname = appldata_proc_name,
.maxlen = 0,
.mode = S_IRUGO | S_IXUGO,
.child = appldata_table,
},
- { .ctl_name = 0 }
+ { },
};
/*
*/
int appldata_register_ops(struct appldata_ops *ops)
{
- struct list_head *lh;
- struct appldata_ops *tmp_ops;
- int i;
-
- i = 0;
+ if ((ops->size > APPLDATA_MAX_REC_SIZE) || (ops->size < 0))
+ return -EINVAL;
- if ((ops->size > APPLDATA_MAX_REC_SIZE) ||
- (ops->size < 0)){
- P_ERROR("Invalid size of %s record = %i, maximum = %i!\n",
- ops->name, ops->size, APPLDATA_MAX_REC_SIZE);
- return -ENOMEM;
- }
- if ((ops->ctl_nr == CTL_APPLDATA) ||
- (ops->ctl_nr == CTL_APPLDATA_TIMER) ||
- (ops->ctl_nr == CTL_APPLDATA_INTERVAL)) {
- P_ERROR("ctl_nr %i already in use!\n", ops->ctl_nr);
- return -EBUSY;
- }
- ops->ctl_table = kzalloc(4*sizeof(struct ctl_table), GFP_KERNEL);
- if (ops->ctl_table == NULL) {
- P_ERROR("Not enough memory for %s ctl_table!\n", ops->name);
+ ops->ctl_table = kzalloc(4 * sizeof(struct ctl_table), GFP_KERNEL);
+ if (!ops->ctl_table)
return -ENOMEM;
- }
spin_lock(&appldata_ops_lock);
- list_for_each(lh, &appldata_ops_list) {
- tmp_ops = list_entry(lh, struct appldata_ops, list);
- P_DEBUG("register_ops loop: %i) name = %s, ctl = %i\n",
- ++i, tmp_ops->name, tmp_ops->ctl_nr);
- P_DEBUG("Comparing %s (ctl %i) with %s (ctl %i)\n",
- tmp_ops->name, tmp_ops->ctl_nr, ops->name,
- ops->ctl_nr);
- if (strncmp(tmp_ops->name, ops->name,
- APPLDATA_PROC_NAME_LENGTH) == 0) {
- P_ERROR("Name \"%s\" already registered!\n", ops->name);
- kfree(ops->ctl_table);
- spin_unlock(&appldata_ops_lock);
- return -EBUSY;
- }
- if (tmp_ops->ctl_nr == ops->ctl_nr) {
- P_ERROR("ctl_nr %i already registered!\n", ops->ctl_nr);
- kfree(ops->ctl_table);
- spin_unlock(&appldata_ops_lock);
- return -EBUSY;
- }
- }
list_add(&ops->list, &appldata_ops_list);
spin_unlock(&appldata_ops_lock);
- ops->ctl_table[0].ctl_name = CTL_APPLDATA;
ops->ctl_table[0].procname = appldata_proc_name;
ops->ctl_table[0].maxlen = 0;
ops->ctl_table[0].mode = S_IRUGO | S_IXUGO;
ops->ctl_table[0].child = &ops->ctl_table[2];
- ops->ctl_table[1].ctl_name = 0;
-
- ops->ctl_table[2].ctl_name = ops->ctl_nr;
ops->ctl_table[2].procname = ops->name;
ops->ctl_table[2].mode = S_IRUGO | S_IWUSR;
ops->ctl_table[2].proc_handler = appldata_generic_handler;
ops->ctl_table[2].data = ops;
- ops->ctl_table[3].ctl_name = 0;
-
ops->sysctl_header = register_sysctl_table(ops->ctl_table);
-
+ if (!ops->sysctl_header)
+ goto out;
P_INFO("%s-ops registered!\n", ops->name);
return 0;
+out:
+ spin_lock(&appldata_ops_lock);
+ list_del(&ops->list);
+ spin_unlock(&appldata_ops_lock);
+ kfree(ops->ctl_table);
+ return -ENOMEM;
}
/*
*/
void appldata_unregister_ops(struct appldata_ops *ops)
{
- void *table;
spin_lock(&appldata_ops_lock);
list_del(&ops->list);
- /* at that point any incoming access will fail */
- table = ops->ctl_table;
- ops->ctl_table = NULL;
spin_unlock(&appldata_ops_lock);
unregister_sysctl_table(ops->sysctl_header);
- kfree(table);
+ kfree(ops->ctl_table);
P_INFO("%s-ops unregistered!\n", ops->name);
}
/********************** module-ops management <END> **************************/
static struct appldata_ops ops = {
- .ctl_nr = CTL_APPLDATA_MEM,
.name = "mem",
.record_nr = APPLDATA_RECORD_MEM_ID,
.size = sizeof(struct appldata_mem_data),
static struct appldata_ops ops = {
- .ctl_nr = CTL_APPLDATA_NET_SUM,
.name = "net_sum",
.record_nr = APPLDATA_RECORD_NET_SUM_ID,
.size = sizeof(struct appldata_net_sum_data),
static struct appldata_os_data *appldata_os_data;
static struct appldata_ops ops = {
- .ctl_nr = CTL_APPLDATA_OS,
.name = "os",
.record_nr = APPLDATA_RECORD_OS_ID,
.owner = THIS_MODULE,
cc = __tprot(addr);
while (cc == old_cc) {
addr += CHUNK_INCR;
- if (addr >= memsize)
+ if (memsize && addr >= memsize)
break;
#ifndef CONFIG_64BIT
if (addr == ADDR2G)
basr %r14,%r1
.endm
- .macro LOCKDEP_SYS_EXIT
- l %r1,BASED(.Llockdep_sys_exit)
+ .macro TRACE_IRQS_CHECK
+ tm SP_PSW(%r15),0x03 # irqs enabled?
+ jz 0f
+ l %r1,BASED(.Ltrace_irq_on)
basr %r14,%r1
+ j 1f
+0: l %r1,BASED(.Ltrace_irq_off)
+ basr %r14,%r1
+1:
.endm
#else
#define TRACE_IRQS_ON
#define TRACE_IRQS_OFF
+#define TRACE_IRQS_CHECK
+#endif
+
+#ifdef CONFIG_LOCKDEP
+ .macro LOCKDEP_SYS_EXIT
+ tm SP_PSW+1(%r15),0x01 # returning to user ?
+ jz 0f
+ l %r1,BASED(.Llockdep_sys_exit)
+ basr %r14,%r1
+0:
+ .endm
+#else
#define LOCKDEP_SYS_EXIT
#endif
lh %r7,0x8a # get svc number from lowcore
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
sysc_vtime:
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- bz BASED(sysc_do_svc)
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
sysc_stime:
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
sysc_return:
tm SP_PSW+1(%r15),0x01 # returning to user ?
- bno BASED(sysc_leave)
+ bno BASED(sysc_restore)
tm __TI_flags+3(%r9),_TIF_WORK_SVC
bnz BASED(sysc_work) # there is work to do (signals etc.)
+sysc_restore:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ la %r1,BASED(sysc_restore_trace_psw)
+ lpsw 0(%r1)
+sysc_restore_trace:
+ TRACE_IRQS_CHECK
LOCKDEP_SYS_EXIT
+#endif
sysc_leave:
RESTORE_ALL __LC_RETURN_PSW,1
+sysc_done:
+
+#ifdef CONFIG_TRACE_IRQFLAGS
+ .align 8
+ .globl sysc_restore_trace_psw
+sysc_restore_trace_psw:
+ .long 0, sysc_restore_trace + 0x80000000
+#endif
#
# recheck if there is more work to do
#
sysc_work_loop:
tm __TI_flags+3(%r9),_TIF_WORK_SVC
- bz BASED(sysc_leave) # there is no work to do
+ bz BASED(sysc_restore) # there is no work to do
#
# One of the work bits is on. Find out which one.
#
bo BASED(sysc_restart)
tm __TI_flags+3(%r9),_TIF_SINGLE_STEP
bo BASED(sysc_singlestep)
- LOCKDEP_SYS_EXIT
- b BASED(sysc_leave)
+ b BASED(sysc_restore)
+sysc_work_done:
#
# _TIF_NEED_RESCHED is set, call schedule
pgm_no_vtime:
#endif
l %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
l %r3,__LC_PGM_ILC # load program interruption code
la %r8,0x7f
nr %r8,%r3
pgm_no_vtime2:
#endif
l %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
l %r1,__TI_task(%r9)
mvc __THREAD_per+__PER_atmid(2,%r1),__LC_PER_ATMID
mvc __THREAD_per+__PER_address(4,%r1),__LC_PER_ADDRESS
SAVE_ALL_SYNC __LC_SVC_OLD_PSW,__LC_SAVE_AREA
CREATE_STACK_FRAME __LC_SVC_OLD_PSW,__LC_SAVE_AREA
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- bz BASED(pgm_no_vtime3)
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
-pgm_no_vtime3:
#endif
lh %r7,0x8a # get svc number from lowcore
l %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
l %r1,__TI_task(%r9)
mvc __THREAD_per+__PER_atmid(2,%r1),__LC_PER_ATMID
mvc __THREAD_per+__PER_address(4,%r1),__LC_PER_ADDRESS
mvi SP_TRAP+1(%r15),0x28 # set trap indication to pgm check
la %r2,SP_PTREGS(%r15) # address of register-save area
l %r1,BASED(.Lhandle_per) # load adr. of per handler
- la %r14,BASED(sysc_leave) # load adr. of system return
+ la %r14,BASED(sysc_restore)# load adr. of system return
br %r1 # branch to do_single_step
/*
l %r1,BASED(.Ldo_IRQ) # load address of do_IRQ
la %r2,SP_PTREGS(%r15) # address of register-save area
basr %r14,%r1 # branch to standard irq handler
- TRACE_IRQS_ON
-
io_return:
tm SP_PSW+1(%r15),0x01 # returning to user ?
#ifdef CONFIG_PREEMPT
bno BASED(io_preempt) # no -> check for preemptive scheduling
#else
- bno BASED(io_leave) # no-> skip resched & signal
+ bno BASED(io_restore) # no-> skip resched & signal
#endif
tm __TI_flags+3(%r9),_TIF_WORK_INT
bnz BASED(io_work) # there is work to do (signals etc.)
+io_restore:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ la %r1,BASED(io_restore_trace_psw)
+ lpsw 0(%r1)
+io_restore_trace:
+ TRACE_IRQS_CHECK
LOCKDEP_SYS_EXIT
+#endif
io_leave:
RESTORE_ALL __LC_RETURN_PSW,0
io_done:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ .align 8
+ .globl io_restore_trace_psw
+io_restore_trace_psw:
+ .long 0, io_restore_trace + 0x80000000
+#endif
+
#ifdef CONFIG_PREEMPT
io_preempt:
icm %r0,15,__TI_precount(%r9)
- bnz BASED(io_leave)
+ bnz BASED(io_restore)
l %r1,SP_R15(%r15)
s %r1,BASED(.Lc_spsize)
mvc SP_PTREGS(__PT_SIZE,%r1),SP_PTREGS(%r15)
lr %r15,%r1
io_resume_loop:
tm __TI_flags+3(%r9),_TIF_NEED_RESCHED
- bno BASED(io_leave)
- mvc __TI_precount(4,%r9),BASED(.Lc_pactive)
- stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
- l %r1,BASED(.Lschedule)
- basr %r14,%r1 # call schedule
- stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
- xc __TI_precount(4,%r9),__TI_precount(%r9)
- b BASED(io_resume_loop)
+ bno BASED(io_restore)
+ l %r1,BASED(.Lpreempt_schedule_irq)
+ la %r14,BASED(io_resume_loop)
+ br %r1 # call schedule
#endif
#
bo BASED(io_reschedule)
tm __TI_flags+3(%r9),(_TIF_SIGPENDING | _TIF_RESTORE_SIGMASK)
bnz BASED(io_sigpending)
- LOCKDEP_SYS_EXIT
- b BASED(io_leave)
+ b BASED(io_restore)
+io_work_done:
#
# _TIF_MCCK_PENDING is set, call handler
#
io_mcck_pending:
- TRACE_IRQS_OFF
l %r1,BASED(.Ls390_handle_mcck)
basr %r14,%r1 # TIF bit will be cleared by handler
- TRACE_IRQS_ON
b BASED(io_work_loop)
#
# _TIF_NEED_RESCHED is set, call schedule
#
io_reschedule:
+ TRACE_IRQS_ON
l %r1,BASED(.Lschedule)
stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
basr %r14,%r1 # call scheduler
stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
+ TRACE_IRQS_OFF
tm __TI_flags+3(%r9),_TIF_WORK_INT
- bz BASED(io_leave) # there is no work to do
+ bz BASED(io_restore) # there is no work to do
b BASED(io_work_loop)
#
# _TIF_SIGPENDING or _TIF_RESTORE_SIGMASK is set, call do_signal
#
io_sigpending:
+ TRACE_IRQS_ON
stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
la %r2,SP_PTREGS(%r15) # load pt_regs
l %r1,BASED(.Ldo_signal)
basr %r14,%r1 # call do_signal
stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
+ TRACE_IRQS_OFF
b BASED(io_work_loop)
/*
lh %r3,__LC_EXT_INT_CODE # get interruption code
l %r1,BASED(.Ldo_extint)
basr %r14,%r1
- TRACE_IRQS_ON
b BASED(io_return)
__critical_end:
cleanup_table_sysc_return:
.long sysc_return + 0x80000000, sysc_leave + 0x80000000
cleanup_table_sysc_leave:
- .long sysc_leave + 0x80000000, sysc_work_loop + 0x80000000
+ .long sysc_leave + 0x80000000, sysc_done + 0x80000000
cleanup_table_sysc_work_loop:
- .long sysc_work_loop + 0x80000000, sysc_reschedule + 0x80000000
+ .long sysc_work_loop + 0x80000000, sysc_work_done + 0x80000000
cleanup_table_io_return:
.long io_return + 0x80000000, io_leave + 0x80000000
cleanup_table_io_leave:
.long io_leave + 0x80000000, io_done + 0x80000000
cleanup_table_io_work_loop:
- .long io_work_loop + 0x80000000, io_mcck_pending + 0x80000000
+ .long io_work_loop + 0x80000000, io_work_done + 0x80000000
cleanup_critical:
clc 4(4,%r12),BASED(cleanup_table_system_call)
cleanup_vtime:
clc __LC_RETURN_PSW+4(4),BASED(cleanup_system_call_insn+12)
bhe BASED(cleanup_stime)
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- bz BASED(cleanup_novtime)
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
cleanup_stime:
clc __LC_RETURN_PSW+4(4),BASED(cleanup_system_call_insn+16)
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
cleanup_update:
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
-cleanup_novtime:
#endif
mvc __LC_RETURN_PSW+4(4),BASED(cleanup_table_system_call+4)
la %r12,__LC_RETURN_PSW
2: la %r12,__LC_RETURN_PSW
br %r14
cleanup_sysc_leave_insn:
+ .long sysc_done - 4 + 0x80000000
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- .long sysc_leave + 14 + 0x80000000
+ .long sysc_done - 8 + 0x80000000
#endif
- .long sysc_leave + 10 + 0x80000000
cleanup_io_return:
mvc __LC_RETURN_PSW(4),0(%r12)
2: la %r12,__LC_RETURN_PSW
br %r14
cleanup_io_leave_insn:
+ .long io_done - 4 + 0x80000000
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- .long io_leave + 18 + 0x80000000
+ .long io_done - 8 + 0x80000000
#endif
- .long io_leave + 14 + 0x80000000
/*
* Integer constants
.align 4
.Lc_spsize: .long SP_SIZE
.Lc_overhead: .long STACK_FRAME_OVERHEAD
-.Lc_pactive: .long PREEMPT_ACTIVE
.Lnr_syscalls: .long NR_syscalls
.L0x018: .short 0x018
.L0x020: .short 0x020
.Lexecve_tail: .long execve_tail
.Ljump_table: .long pgm_check_table
.Lschedule: .long schedule
+.Lpreempt_schedule_irq:
+ .long preempt_schedule_irq
.Ltrace: .long syscall_trace
.Lschedtail: .long schedule_tail
.Lsysc_table: .long sys_call_table
brasl %r14,trace_hardirqs_off
.endm
- .macro LOCKDEP_SYS_EXIT
- brasl %r14,lockdep_sys_exit
+ .macro TRACE_IRQS_CHECK
+ tm SP_PSW(%r15),0x03 # irqs enabled?
+ jz 0f
+ brasl %r14,trace_hardirqs_on
+ j 1f
+0: brasl %r14,trace_hardirqs_off
+1:
.endm
#else
#define TRACE_IRQS_ON
#define TRACE_IRQS_OFF
+#define TRACE_IRQS_CHECK
+#endif
+
+#ifdef CONFIG_LOCKDEP
+ .macro LOCKDEP_SYS_EXIT
+ tm SP_PSW+1(%r15),0x01 # returning to user ?
+ jz 0f
+ brasl %r14,lockdep_sys_exit
+0:
+ .endm
+#else
#define LOCKDEP_SYS_EXIT
#endif
llgh %r7,__LC_SVC_INT_CODE # get svc number from lowcore
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
sysc_vtime:
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- jz sysc_do_svc
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
sysc_stime:
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
sysc_return:
tm SP_PSW+1(%r15),0x01 # returning to user ?
- jno sysc_leave
+ jno sysc_restore
tm __TI_flags+7(%r9),_TIF_WORK_SVC
jnz sysc_work # there is work to do (signals etc.)
+sysc_restore:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ larl %r1,sysc_restore_trace_psw
+ lpswe 0(%r1)
+sysc_restore_trace:
+ TRACE_IRQS_CHECK
LOCKDEP_SYS_EXIT
+#endif
sysc_leave:
RESTORE_ALL __LC_RETURN_PSW,1
+sysc_done:
+
+#ifdef CONFIG_TRACE_IRQFLAGS
+ .align 8
+ .globl sysc_restore_trace_psw
+sysc_restore_trace_psw:
+ .quad 0, sysc_restore_trace
+#endif
#
# recheck if there is more work to do
#
sysc_work_loop:
tm __TI_flags+7(%r9),_TIF_WORK_SVC
- jz sysc_leave # there is no work to do
+ jz sysc_restore # there is no work to do
#
# One of the work bits is on. Find out which one.
#
jo sysc_restart
tm __TI_flags+7(%r9),_TIF_SINGLE_STEP
jo sysc_singlestep
- LOCKDEP_SYS_EXIT
- j sysc_leave
+ j sysc_restore
+sysc_work_done:
#
# _TIF_NEED_RESCHED is set, call schedule
pgm_no_vtime:
#endif
lg %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
lgf %r3,__LC_PGM_ILC # load program interruption code
lghi %r8,0x7f
ngr %r8,%r3
pgm_no_vtime2:
#endif
lg %r9,__LC_THREAD_INFO # load pointer to thread_info struct
+ TRACE_IRQS_OFF
lg %r1,__TI_task(%r9)
tm SP_PSW+1(%r15),0x01 # kernel per event ?
jz kernel_per
SAVE_ALL_SYNC __LC_SVC_OLD_PSW,__LC_SAVE_AREA
CREATE_STACK_FRAME __LC_SVC_OLD_PSW,__LC_SAVE_AREA
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- jz pgm_no_vtime3
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
-pgm_no_vtime3:
#endif
llgh %r7,__LC_SVC_INT_CODE # get svc number from lowcore
lg %r9,__LC_THREAD_INFO # load pointer to thread_info struct
lhi %r0,__LC_PGM_OLD_PSW
sth %r0,SP_TRAP(%r15) # set trap indication to pgm check
la %r2,SP_PTREGS(%r15) # address of register-save area
- larl %r14,sysc_leave # load adr. of system ret, no work
+ larl %r14,sysc_restore # load adr. of system ret, no work
jg do_single_step # branch to do_single_step
/*
TRACE_IRQS_OFF
la %r2,SP_PTREGS(%r15) # address of register-save area
brasl %r14,do_IRQ # call standard irq handler
- TRACE_IRQS_ON
-
io_return:
tm SP_PSW+1(%r15),0x01 # returning to user ?
#ifdef CONFIG_PREEMPT
jno io_preempt # no -> check for preemptive scheduling
#else
- jno io_leave # no-> skip resched & signal
+ jno io_restore # no-> skip resched & signal
#endif
tm __TI_flags+7(%r9),_TIF_WORK_INT
jnz io_work # there is work to do (signals etc.)
+io_restore:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ larl %r1,io_restore_trace_psw
+ lpswe 0(%r1)
+io_restore_trace:
+ TRACE_IRQS_CHECK
LOCKDEP_SYS_EXIT
+#endif
io_leave:
RESTORE_ALL __LC_RETURN_PSW,0
io_done:
+#ifdef CONFIG_TRACE_IRQFLAGS
+ .align 8
+ .globl io_restore_trace_psw
+io_restore_trace_psw:
+ .quad 0, io_restore_trace
+#endif
+
#ifdef CONFIG_PREEMPT
io_preempt:
icm %r0,15,__TI_precount(%r9)
- jnz io_leave
+ jnz io_restore
# switch to kernel stack
lg %r1,SP_R15(%r15)
aghi %r1,-SP_SIZE
lgr %r15,%r1
io_resume_loop:
tm __TI_flags+7(%r9),_TIF_NEED_RESCHED
- jno io_leave
- larl %r1,.Lc_pactive
- mvc __TI_precount(4,%r9),0(%r1)
- stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
- brasl %r14,schedule # call schedule
- stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
- xc __TI_precount(4,%r9),__TI_precount(%r9)
- j io_resume_loop
+ jno io_restore
+ larl %r14,io_resume_loop
+ jg preempt_schedule_irq
#endif
#
jo io_reschedule
tm __TI_flags+7(%r9),(_TIF_SIGPENDING | _TIF_RESTORE_SIGMASK)
jnz io_sigpending
- LOCKDEP_SYS_EXIT
- j io_leave
+ j io_restore
+io_work_done:
#
# _TIF_MCCK_PENDING is set, call handler
#
io_mcck_pending:
- TRACE_IRQS_OFF
brasl %r14,s390_handle_mcck # TIF bit will be cleared by handler
- TRACE_IRQS_ON
j io_work_loop
#
# _TIF_NEED_RESCHED is set, call schedule
#
io_reschedule:
+ TRACE_IRQS_ON
stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
brasl %r14,schedule # call scheduler
stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
+ TRACE_IRQS_OFF
tm __TI_flags+7(%r9),_TIF_WORK_INT
- jz io_leave # there is no work to do
+ jz io_restore # there is no work to do
j io_work_loop
#
# _TIF_SIGPENDING or _TIF_RESTORE_SIGMASK is set, call do_signal
#
io_sigpending:
+ TRACE_IRQS_ON
stosm __SF_EMPTY(%r15),0x03 # reenable interrupts
la %r2,SP_PTREGS(%r15) # load pt_regs
brasl %r14,do_signal # call do_signal
stnsm __SF_EMPTY(%r15),0xfc # disable I/O and ext. interrupts
+ TRACE_IRQS_OFF
j io_work_loop
/*
la %r2,SP_PTREGS(%r15) # address of register-save area
llgh %r3,__LC_EXT_INT_CODE # get interruption code
brasl %r14,do_extint
- TRACE_IRQS_ON
j io_return
__critical_end:
cleanup_table_sysc_return:
.quad sysc_return, sysc_leave
cleanup_table_sysc_leave:
- .quad sysc_leave, sysc_work_loop
+ .quad sysc_leave, sysc_done
cleanup_table_sysc_work_loop:
- .quad sysc_work_loop, sysc_reschedule
+ .quad sysc_work_loop, sysc_work_done
cleanup_table_io_return:
.quad io_return, io_leave
cleanup_table_io_leave:
.quad io_leave, io_done
cleanup_table_io_work_loop:
- .quad io_work_loop, io_mcck_pending
+ .quad io_work_loop, io_work_done
cleanup_critical:
clc 8(8,%r12),BASED(cleanup_table_system_call)
cleanup_vtime:
clc __LC_RETURN_PSW+8(8),BASED(cleanup_system_call_insn+24)
jhe cleanup_stime
- tm SP_PSW+1(%r15),0x01 # interrupting from user ?
- jz cleanup_novtime
UPDATE_VTIME __LC_EXIT_TIMER,__LC_SYNC_ENTER_TIMER,__LC_USER_TIMER
cleanup_stime:
clc __LC_RETURN_PSW+8(8),BASED(cleanup_system_call_insn+32)
UPDATE_VTIME __LC_LAST_UPDATE_TIMER,__LC_EXIT_TIMER,__LC_SYSTEM_TIMER
cleanup_update:
mvc __LC_LAST_UPDATE_TIMER(8),__LC_SYNC_ENTER_TIMER
-cleanup_novtime:
#endif
mvc __LC_RETURN_PSW+8(8),BASED(cleanup_table_system_call+8)
la %r12,__LC_RETURN_PSW
2: la %r12,__LC_RETURN_PSW
br %r14
cleanup_sysc_leave_insn:
+ .quad sysc_done - 4
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- .quad sysc_leave + 16
+ .quad sysc_done - 8
#endif
- .quad sysc_leave + 12
cleanup_io_return:
mvc __LC_RETURN_PSW(8),0(%r12)
2: la %r12,__LC_RETURN_PSW
br %r14
cleanup_io_leave_insn:
+ .quad io_done - 4
#ifdef CONFIG_VIRT_CPU_ACCOUNTING
- .quad io_leave + 20
+ .quad io_done - 8
#endif
- .quad io_leave + 16
/*
* Integer constants
*/
.align 4
.Lconst:
-.Lc_pactive: .long PREEMPT_ACTIVE
.Lnr_syscalls: .long NR_syscalls
.L0x0130: .short 0x130
.L0x0140: .short 0x140
void machine_restart(char *command)
{
- if (!in_interrupt() || oops_in_progress)
+ if ((!in_interrupt() && !in_atomic()) || oops_in_progress)
/*
* Only unblank the console if we are called in enabled
* context or a bust_spinlocks cleared the way for us.
printk("S390 address spaces switched, ");
set_amode_and_uaccess(PSW_ASC_PRIMARY, PSW32_ASC_PRIMARY);
}
+#ifdef CONFIG_TRACE_IRQFLAGS
+ sysc_restore_trace_psw.mask = psw_kernel_bits & ~PSW_MASK_MCHECK;
+ io_restore_trace_psw.mask = psw_kernel_bits & ~PSW_MASK_MCHECK;
+#endif
}
static void __init
}
EXPORT_SYMBOL(smp_call_function_single);
-static void do_send_stop(void)
+void smp_send_stop(void)
{
int cpu, rc;
- /* stop all processors */
- for_each_online_cpu(cpu) {
- if (cpu == smp_processor_id())
- continue;
- do {
- rc = signal_processor(cpu, sigp_stop);
- } while (rc == sigp_busy);
- }
-}
+ /* Disable all interrupts/machine checks */
+ __load_psw_mask(psw_kernel_bits & ~PSW_MASK_MCHECK);
-static void do_store_status(void)
-{
- int cpu, rc;
+ /* write magic number to zero page (absolute 0) */
+ lowcore_ptr[smp_processor_id()]->panic_magic = __PANIC_MAGIC;
- /* store status of all processors in their lowcores (real 0) */
+ /* stop all processors */
for_each_online_cpu(cpu) {
if (cpu == smp_processor_id())
continue;
do {
- rc = signal_processor_p(
- (__u32)(unsigned long) lowcore_ptr[cpu], cpu,
- sigp_store_status_at_address);
+ rc = signal_processor(cpu, sigp_stop);
} while (rc == sigp_busy);
- }
-}
-static void do_wait_for_stop(void)
-{
- int cpu;
-
- /* Wait for all other cpus to enter stopped state */
- for_each_online_cpu(cpu) {
- if (cpu == smp_processor_id())
- continue;
while (!smp_cpu_not_running(cpu))
cpu_relax();
}
}
-/*
- * this function sends a 'stop' sigp to all other CPUs in the system.
- * it goes straight through.
- */
-void smp_send_stop(void)
-{
- /* Disable all interrupts/machine checks */
- __load_psw_mask(psw_kernel_bits & ~PSW_MASK_MCHECK);
-
- /* write magic number to zero page (absolute 0) */
- lowcore_ptr[smp_processor_id()]->panic_magic = __PANIC_MAGIC;
-
- /* stop other processors. */
- do_send_stop();
-
- /* wait until other processors are stopped */
- do_wait_for_stop();
-
- /* store status of other processors. */
- do_store_status();
-}
-
/*
* Reboot, halt and power_off routines for SMP.
*/
bust_spinlocks(1);
printk("%s: %04lx [#%d]\n", str, err & 0xffff, ++die_counter);
print_modules();
+ notify_die(DIE_OOPS, str, regs, err, current->thread.trap_no, SIGSEGV);
show_regs(regs);
bust_spinlocks(0);
add_taint(TAINT_DIE);
static struct ctl_table cmm_table[] = {
{
- .ctl_name = VM_CMM_PAGES,
.procname = "cmm_pages",
.mode = 0644,
.proc_handler = &cmm_pages_handler,
},
{
- .ctl_name = VM_CMM_TIMED_PAGES,
.procname = "cmm_timed_pages",
.mode = 0644,
.proc_handler = &cmm_pages_handler,
},
{
- .ctl_name = VM_CMM_TIMEOUT,
.procname = "cmm_timeout",
.mode = 0644,
.proc_handler = &cmm_timeout_handler,
$(srctree)/arch/x86/Makefile%: ;
ifeq ($(CONFIG_X86_32),y)
+ UTS_MACHINE := i386
include $(srctree)/arch/x86/Makefile_32
else
+ UTS_MACHINE := x86_64
include $(srctree)/arch/x86/Makefile_64
endif
-
-
-
if (cpu_has(c, X86_FEATURE_EST))
buf[2] |= ACPI_PDC_EST_CAPABILITY_SWSMP;
+ if (cpu_has(c, X86_FEATURE_ACPI))
+ buf[2] |= ACPI_PDC_T_FFH;
+
obj->type = ACPI_TYPE_BUFFER;
obj->buffer.length = 12;
obj->buffer.pointer = (u8 *) buf;
__setup("acpi_sleep=", acpi_sleep_setup);
-void acpi_pci_link_exit(void)
-{
-}
#define default_MCA_trigger(idx) (1)
#define default_MCA_polarity(idx) (0)
-static int __init MPBIOS_polarity(int idx)
+static int MPBIOS_polarity(int idx)
{
int bus = mp_irqs[idx].mpc_srcbus;
int polarity;
return 0;
}
+int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity)
+{
+ int i;
+
+ if (skip_ioapic_setup)
+ return -1;
+
+ for (i = 0; i < mp_irq_entries; i++)
+ if (mp_irqs[i].mpc_irqtype == mp_INT &&
+ mp_irqs[i].mpc_srcbusirq == bus_irq)
+ break;
+ if (i >= mp_irq_entries)
+ return -1;
+
+ *trigger = irq_trigger(i);
+ *polarity = irq_polarity(i);
+ return 0;
+}
+
#endif /* CONFIG_ACPI */
static int __init parse_disable_timer_pin_1(char *arg)
#define default_PCI_trigger(idx) (1)
#define default_PCI_polarity(idx) (1)
-static int __init MPBIOS_polarity(int idx)
+static int MPBIOS_polarity(int idx)
{
int bus = mp_irqs[idx].mpc_srcbus;
int polarity;
return 0;
}
-#endif /* CONFIG_ACPI */
+int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity)
+{
+ int i;
+
+ if (skip_ioapic_setup)
+ return -1;
+
+ for (i = 0; i < mp_irq_entries; i++)
+ if (mp_irqs[i].mpc_irqtype == mp_INT &&
+ mp_irqs[i].mpc_srcbusirq == bus_irq)
+ break;
+ if (i >= mp_irq_entries)
+ return -1;
+
+ *trigger = irq_trigger(i);
+ *polarity = irq_polarity(i);
+ return 0;
+}
+
+#endif /* CONFIG_ACPI */
/*
* This function currently is only a helper for the i386 smp boot process where
}
}
#endif
+
return 0;
}
-static struct dmi_system_id acpi_pciprobe_dmi_table[] = {
+static struct dmi_system_id acpi_pciprobe_dmi_table[] __devinitdata = {
/*
* Systems where PCI IO resource ISA alignment can be skipped
* when the ISA enable bit in the bridge control is not set
config ACPI_PROCFS
bool "Deprecated /proc/acpi files"
depends on PROC_FS
- default y
---help---
For backwards compatibility, this option allows
deprecated /proc/acpi/ files to exist, even when
/proc/acpi/info (/sys/modules/acpi/parameters/acpica_version)
/proc/acpi/dsdt (/sys/firmware/acpi/tables/DSDT)
/proc/acpi/fadt (/sys/firmware/acpi/tables/FACP)
- /proc/acpi/battery (/sys/class/power_supply)
/proc/acpi/debug_layer (/sys/module/acpi/parameters/debug_layer)
/proc/acpi/debug_level (/sys/module/acpi/parameters/debug_level)
and functions which do not yet exist in /sys.
Say N to delete /proc/acpi/ files that have moved to /sys/
-
+config ACPI_PROCFS_POWER
+ bool "Deprecated power /proc/acpi folders"
+ depends on PROC_FS
+ default y
+ ---help---
+ For backwards compatibility, this option allows
+ deprecated power /proc/acpi/ folders to exist, even when
+ they have been replaced by functions in /sys.
+ The deprecated folders (and their replacements) include:
+ /proc/acpi/battery/* (/sys/class/power_supply/*)
+ /proc/acpi/ac_adapter/* (sys/class/power_supply/*)
+ This option has no effect on /proc/acpi/ folders
+ and functions, which do not yet exist in /sys
+
+ Say N to delete power /proc/acpi/ folders that have moved to /sys/
config ACPI_PROC_EVENT
bool "Deprecated /proc/acpi/event support"
depends on PROC_FS
obj-$(CONFIG_ACPI_ASUS) += asus_acpi.o
obj-$(CONFIG_ACPI_TOSHIBA) += toshiba_acpi.o
obj-$(CONFIG_ACPI_HOTPLUG_MEMORY) += acpi_memhotplug.o
-obj-y += cm_sbs.o
+obj-$(CONFIG_ACPI_PROCFS_POWER) += cm_sbs.o
obj-$(CONFIG_ACPI_SBS) += sbs.o
obj-$(CONFIG_ACPI_SBS) += sbshc.o
#include <linux/module.h>
#include <linux/init.h>
#include <linux/types.h>
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#endif
MODULE_DESCRIPTION("ACPI AC Adapter Driver");
MODULE_LICENSE("GPL");
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
extern struct proc_dir_entry *acpi_lock_ac_dir(void);
extern void *acpi_unlock_ac_dir(struct proc_dir_entry *acpi_ac_dir);
static int acpi_ac_open_fs(struct inode *inode, struct file *file);
#define to_acpi_ac(x) container_of(x, struct acpi_ac, charger);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
static const struct file_operations acpi_ac_fops = {
.open = acpi_ac_open_fs,
.read = seq_read,
return 0;
}
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
/* --------------------------------------------------------------------------
FS Interface (/proc)
-------------------------------------------------------------------------- */
if (result)
goto end;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
result = acpi_ac_add_fs(device);
#endif
if (result)
end:
if (result) {
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_remove_fs(device);
#endif
kfree(ac);
ACPI_ALL_NOTIFY, acpi_ac_notify);
if (ac->charger.dev)
power_supply_unregister(&ac->charger);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_remove_fs(device);
#endif
if (acpi_disabled)
return -ENODEV;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_dir = acpi_lock_ac_dir();
if (!acpi_ac_dir)
return -ENODEV;
result = acpi_bus_register_driver(&acpi_ac_driver);
if (result < 0) {
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_unlock_ac_dir(acpi_ac_dir);
#endif
return -ENODEV;
acpi_bus_unregister_driver(&acpi_ac_driver);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_unlock_ac_dir(acpi_ac_dir);
#endif
#include <linux/types.h>
#include <linux/jiffies.h>
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <asm/uaccess.h>
module_param(cache_time, uint, 0644);
MODULE_PARM_DESC(cache_time, "cache time in milliseconds");
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
extern struct proc_dir_entry *acpi_lock_battery_dir(void);
extern void *acpi_unlock_battery_dir(struct proc_dir_entry *acpi_battery_dir);
val->intval = POWER_SUPPLY_STATUS_CHARGING;
else if (battery->state == 0)
val->intval = POWER_SUPPLY_STATUS_FULL;
+ else
+ val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
break;
case POWER_SUPPLY_PROP_PRESENT:
val->intval = acpi_battery_present(battery);
POWER_SUPPLY_PROP_MANUFACTURER,
};
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
inline char *acpi_battery_units(struct acpi_battery *battery)
{
return (battery->power_unit)?"mA":"mW";
FS Interface (/proc)
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
static struct proc_dir_entry *acpi_battery_dir;
static int acpi_battery_print_info(struct seq_file *seq, int result)
acpi_driver_data(device) = battery;
mutex_init(&battery->lock);
acpi_battery_update(battery);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
result = acpi_battery_add_fs(device);
if (result)
goto end;
device->status.battery_present ? "present" : "absent");
end:
if (result) {
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_battery_remove_fs(device);
#endif
kfree(battery);
status = acpi_remove_notify_handler(device->handle,
ACPI_ALL_NOTIFY,
acpi_battery_notify);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_battery_remove_fs(device);
#endif
sysfs_remove_battery(battery);
{
if (acpi_disabled)
return -ENODEV;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_battery_dir = acpi_lock_battery_dir();
if (!acpi_battery_dir)
return -ENODEV;
#endif
if (acpi_bus_register_driver(&acpi_battery_driver) < 0) {
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_unlock_battery_dir(acpi_battery_dir);
#endif
return -ENODEV;
static void __exit acpi_battery_exit(void)
{
acpi_bus_unregister_driver(&acpi_battery_driver);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_unlock_battery_dir(acpi_battery_dir);
#endif
}
#undef PREFIX
#define PREFIX "ACPI: EC: "
+/* Uncomment next line to get verbose print outs*/
+/* #define DEBUG */
+
/* EC status register */
#define ACPI_EC_FLAG_OBF 0x01 /* Output buffer full */
#define ACPI_EC_FLAG_IBF 0x02 /* Input buffer full */
EC_FLAGS_WAIT_GPE = 0, /* Don't check status until GPE arrives */
EC_FLAGS_QUERY_PENDING, /* Query is pending */
EC_FLAGS_GPE_MODE, /* Expect GPE to be sent for status change */
- EC_FLAGS_ONLY_IBF_GPE, /* Expect GPE only for IBF = 0 event */
+ EC_FLAGS_NO_ADDRESS_GPE, /* Expect GPE only for non-address event */
+ EC_FLAGS_ADDRESS, /* Address is being written */
+ EC_FLAGS_NO_WDATA_GPE, /* Don't expect WDATA GPE event */
+ EC_FLAGS_WDATA, /* Data is being written */
};
static int acpi_ec_remove(struct acpi_device *device, int type);
static inline u8 acpi_ec_read_status(struct acpi_ec *ec)
{
- return inb(ec->command_addr);
+ u8 x = inb(ec->command_addr);
+ pr_debug(PREFIX "---> status = 0x%2x\n", x);
+ return x;
}
static inline u8 acpi_ec_read_data(struct acpi_ec *ec)
{
+ u8 x = inb(ec->data_addr);
+ pr_debug(PREFIX "---> data = 0x%2x\n", x);
return inb(ec->data_addr);
}
static inline void acpi_ec_write_cmd(struct acpi_ec *ec, u8 command)
{
+ pr_debug(PREFIX "<--- command = 0x%2x\n", command);
outb(command, ec->command_addr);
}
static inline void acpi_ec_write_data(struct acpi_ec *ec, u8 data)
{
+ pr_debug(PREFIX "<--- data = 0x%2x\n", data);
outb(data, ec->data_addr);
}
static int acpi_ec_wait(struct acpi_ec *ec, enum ec_event event, int force_poll)
{
+ int ret = 0;
+ if (unlikely(test_bit(EC_FLAGS_ADDRESS, &ec->flags) &&
+ test_bit(EC_FLAGS_NO_ADDRESS_GPE, &ec->flags)))
+ force_poll = 1;
+ if (unlikely(test_bit(EC_FLAGS_WDATA, &ec->flags) &&
+ test_bit(EC_FLAGS_NO_WDATA_GPE, &ec->flags)))
+ force_poll = 1;
if (likely(test_bit(EC_FLAGS_GPE_MODE, &ec->flags)) &&
likely(!force_poll)) {
if (wait_event_timeout(ec->wait, acpi_ec_check_status(ec, event),
msecs_to_jiffies(ACPI_EC_DELAY)))
- return 0;
+ goto end;
clear_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
if (acpi_ec_check_status(ec, event)) {
- if (event == ACPI_EC_EVENT_OBF_1) {
- /* miss OBF = 1 GPE, don't expect it anymore */
- printk(KERN_INFO PREFIX "missing OBF_1 confirmation,"
- "switching to degraded mode.\n");
- set_bit(EC_FLAGS_ONLY_IBF_GPE, &ec->flags);
+ if (test_bit(EC_FLAGS_ADDRESS, &ec->flags)) {
+ /* miss address GPE, don't expect it anymore */
+ pr_info(PREFIX "missing address confirmation, "
+ "don't expect it any longer.\n");
+ set_bit(EC_FLAGS_NO_ADDRESS_GPE, &ec->flags);
+ } else if (test_bit(EC_FLAGS_WDATA, &ec->flags)) {
+ /* miss write data GPE, don't expect it */
+ pr_info(PREFIX "missing write data confirmation, "
+ "don't expect it any longer.\n");
+ set_bit(EC_FLAGS_NO_WDATA_GPE, &ec->flags);
} else {
/* missing GPEs, switch back to poll mode */
- printk(KERN_INFO PREFIX "missing IBF_1 confirmations,"
- "switch off interrupt mode.\n");
+ if (printk_ratelimit())
+ pr_info(PREFIX "missing confirmations, "
+ "switch off interrupt mode.\n");
clear_bit(EC_FLAGS_GPE_MODE, &ec->flags);
}
- return 0;
+ goto end;
}
} else {
unsigned long delay = jiffies + msecs_to_jiffies(ACPI_EC_DELAY);
clear_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
while (time_before(jiffies, delay)) {
if (acpi_ec_check_status(ec, event))
- return 0;
+ goto end;
}
}
- printk(KERN_ERR PREFIX "acpi_ec_wait timeout,"
+ pr_err(PREFIX "acpi_ec_wait timeout,"
" status = %d, expect_event = %d\n",
acpi_ec_read_status(ec), event);
- return -ETIME;
+ ret = -ETIME;
+ end:
+ clear_bit(EC_FLAGS_ADDRESS, &ec->flags);
+ return ret;
}
static int acpi_ec_transaction_unlocked(struct acpi_ec *ec, u8 command,
int result = 0;
set_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
acpi_ec_write_cmd(ec, command);
-
+ pr_debug(PREFIX "transaction start\n");
for (; wdata_len > 0; --wdata_len) {
result = acpi_ec_wait(ec, ACPI_EC_EVENT_IBF_0, force_poll);
if (result) {
- printk(KERN_ERR PREFIX
+ pr_err(PREFIX
"write_cmd timeout, command = %d\n", command);
goto end;
}
+ /* mark the address byte written to EC */
+ if (rdata_len + wdata_len > 1)
+ set_bit(EC_FLAGS_ADDRESS, &ec->flags);
set_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
acpi_ec_write_data(ec, *(wdata++));
}
if (!rdata_len) {
+ set_bit(EC_FLAGS_WDATA, &ec->flags);
result = acpi_ec_wait(ec, ACPI_EC_EVENT_IBF_0, force_poll);
if (result) {
- printk(KERN_ERR PREFIX
+ pr_err(PREFIX
"finish-write timeout, command = %d\n", command);
goto end;
}
clear_bit(EC_FLAGS_QUERY_PENDING, &ec->flags);
for (; rdata_len > 0; --rdata_len) {
- if (test_bit(EC_FLAGS_ONLY_IBF_GPE, &ec->flags))
- force_poll = 1;
result = acpi_ec_wait(ec, ACPI_EC_EVENT_OBF_1, force_poll);
if (result) {
- printk(KERN_ERR PREFIX "read timeout, command = %d\n",
- command);
+ pr_err(PREFIX "read timeout, command = %d\n", command);
goto end;
}
/* Don't expect GPE after last read */
*(rdata++) = acpi_ec_read_data(ec);
}
end:
+ pr_debug(PREFIX "transaction end\n");
return result;
}
status = acpi_ec_wait(ec, ACPI_EC_EVENT_IBF_0, 0);
if (status) {
- printk(KERN_ERR PREFIX
- "input buffer is not empty, aborting transaction\n");
+ pr_err(PREFIX "input buffer is not empty, "
+ "aborting transaction\n");
goto end;
}
acpi_status status = AE_OK;
struct acpi_ec *ec = data;
+ pr_debug(PREFIX "~~~> interrupt\n");
clear_bit(EC_FLAGS_WAIT_GPE, &ec->flags);
if (test_bit(EC_FLAGS_GPE_MODE, &ec->flags))
wake_up(&ec->wait);
acpi_ec_gpe_query, ec);
} else if (unlikely(!test_bit(EC_FLAGS_GPE_MODE, &ec->flags))) {
/* this is non-query, must be confirmation */
- printk(KERN_INFO PREFIX "non-query interrupt received,"
- " switching to interrupt mode\n");
+ if (printk_ratelimit())
+ pr_info(PREFIX "non-query interrupt received,"
+ " switching to interrupt mode\n");
set_bit(EC_FLAGS_GPE_MODE, &ec->flags);
}
{
if (ACPI_FAILURE(acpi_remove_address_space_handler(ec->handle,
ACPI_ADR_SPACE_EC, &acpi_ec_space_handler)))
- printk(KERN_ERR PREFIX "failed to remove space handler\n");
+ pr_err(PREFIX "failed to remove space handler\n");
if (ACPI_FAILURE(acpi_remove_gpe_handler(NULL, ec->gpe,
&acpi_ec_gpe_handler)))
- printk(KERN_ERR PREFIX "failed to remove gpe handler\n");
+ pr_err(PREFIX "failed to remove gpe handler\n");
ec->handlers_installed = 0;
}
first_ec = ec;
acpi_driver_data(device) = ec;
acpi_ec_add_fs(device);
- printk(KERN_INFO PREFIX "GPE = 0x%lx, I/O: command/status = 0x%lx, data = 0x%lx\n",
+ pr_info(PREFIX "GPE = 0x%lx, I/O: command/status = 0x%lx, data = 0x%lx\n",
ec->gpe, ec->command_addr, ec->data_addr);
- printk(KERN_INFO PREFIX "driver started in %s mode\n",
+ pr_info(PREFIX "driver started in %s mode\n",
(test_bit(EC_FLAGS_GPE_MODE, &ec->flags))?"interrupt":"poll");
return 0;
}
status = acpi_get_table(ACPI_SIG_ECDT, 1,
(struct acpi_table_header **)&ecdt_ptr);
if (ACPI_SUCCESS(status)) {
- printk(KERN_INFO PREFIX "EC description table is found, configuring boot EC\n");
+ pr_info(PREFIX "EC description table is found, configuring boot EC\n");
boot_ec->command_addr = ecdt_ptr->control.address;
boot_ec->data_addr = ecdt_ptr->data.address;
boot_ec->gpe = ecdt_ptr->gpe;
boot_ec->handle = ACPI_ROOT_OBJECT;
} else {
+ /* This workaround is needed only on some broken machines,
+ * which require early EC, but fail to provide ECDT */
+ acpi_handle x;
printk(KERN_DEBUG PREFIX "Look up EC in DSDT\n");
status = acpi_get_devices(ec_device_ids[0].id, ec_parse_device,
boot_ec, NULL);
/* Check that acpi_get_devices actually find something */
if (ACPI_FAILURE(status) || !boot_ec->handle)
goto error;
+ /* We really need to limit this workaround, the only ASUS,
+ * which needs it, has fake EC._INI method, so use it as flag.
+ */
+ if (ACPI_FAILURE(acpi_get_handle(boot_ec->handle, "_INI", &x)))
+ goto error;
}
ret = ec_install_handlers(boot_ec);
if (!value)
value = &dummy;
- switch (width) {
- case 8:
+ *value = 0;
+ if (width <= 8) {
*(u8 *) value = inb(port);
- break;
- case 16:
+ } else if (width <= 16) {
*(u16 *) value = inw(port);
- break;
- case 32:
+ } else if (width <= 32) {
*(u32 *) value = inl(port);
- break;
- default:
+ } else {
BUG();
}
acpi_status acpi_os_write_port(acpi_io_address port, u32 value, u32 width)
{
- switch (width) {
- case 8:
+ if (width <= 8) {
outb(value, port);
- break;
- case 16:
+ } else if (width <= 16) {
outw(value, port);
- break;
- case 32:
+ } else if (width <= 32) {
outl(value, port);
- break;
- default:
+ } else {
BUG();
}
request_region(pr->throttling.address, 6, "ACPI CPU throttle");
}
-#ifdef CONFIG_CPU_FREQ
- acpi_processor_ppc_has_changed(pr);
-#endif
- acpi_processor_get_throttling_info(pr);
- acpi_processor_get_limit_info(pr);
-
return 0;
}
*/
if (processor_device_array[pr->id] != NULL &&
processor_device_array[pr->id] != device) {
- printk(KERN_WARNING "BIOS reported wrong ACPI id"
+ printk(KERN_WARNING "BIOS reported wrong ACPI id "
"for the processor\n");
return -ENODEV;
}
/* _PDC call should be done before doing anything else (if reqd.). */
arch_acpi_processor_init_pdc(pr);
acpi_processor_set_pdc(pr);
+#ifdef CONFIG_CPU_FREQ
+ acpi_processor_ppc_has_changed(pr);
+#endif
+ acpi_processor_get_throttling_info(pr);
+ acpi_processor_get_limit_info(pr);
+
acpi_processor_power_init(pr, device);
{
struct acpi_processor *pr = data;
struct acpi_device *device = NULL;
-
+ int saved;
if (!pr)
return;
switch (event) {
case ACPI_PROCESSOR_NOTIFY_PERFORMANCE:
+ saved = pr->performance_platform_limit;
acpi_processor_ppc_has_changed(pr);
+ if (saved == pr->performance_platform_limit)
+ break;
acpi_bus_generate_proc_event(device, event,
pr->performance_platform_limit);
acpi_bus_generate_netlink_event(device->pnp.device_class,
return PM_TIMER_TICKS_TO_US((0xFFFFFFFF - t1) + t2);
}
+static void acpi_safe_halt(void)
+{
+ current_thread_info()->status &= ~TS_POLLING;
+ /*
+ * TS_POLLING-cleared state must be visible before we
+ * test NEED_RESCHED:
+ */
+ smp_mb();
+ if (!need_resched())
+ safe_halt();
+ current_thread_info()->status |= TS_POLLING;
+}
+
#ifndef CONFIG_CPU_IDLE
static void
return;
}
-static void acpi_safe_halt(void)
-{
- current_thread_info()->status &= ~TS_POLLING;
- /*
- * TS_POLLING-cleared state must be visible before we
- * test NEED_RESCHED:
- */
- smp_mb();
- if (!need_resched())
- safe_halt();
- current_thread_info()->status |= TS_POLLING;
-}
-
static atomic_t c3_cpu_count;
/* Common C-state entry for C2, C3, .. */
if (pr->flags.bm_check)
acpi_idle_update_bm_rld(pr, cx);
- current_thread_info()->status &= ~TS_POLLING;
- /*
- * TS_POLLING-cleared state must be visible before we test
- * NEED_RESCHED:
- */
- smp_mb();
- if (!need_resched())
- safe_halt();
- current_thread_info()->status |= TS_POLLING;
+ acpi_safe_halt();
cx->usage++;
struct acpi_processor *pr;
struct acpi_processor_cx *cx = cpuidle_get_statedata(state);
u32 t1, t2;
+ int sleep_ticks = 0;
+
pr = processors[smp_processor_id()];
if (unlikely(!pr))
ACPI_FLUSH_CPU_CACHE();
t1 = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ /* Tell the scheduler that we are going deep-idle: */
+ sched_clock_idle_sleep_event();
acpi_state_timer_broadcast(pr, cx, 1);
acpi_idle_do_entry(cx);
t2 = inl(acpi_gbl_FADT.xpm_timer_block.address);
/* TSC could halt in idle, so notify users */
mark_tsc_unstable("TSC halts in idle");;
#endif
+ sleep_ticks = ticks_elapsed(t1, t2);
+
+ /* Tell the scheduler how much we idled: */
+ sched_clock_idle_wakeup_event(sleep_ticks*PM_TIMER_TICK_NS);
local_irq_enable();
current_thread_info()->status |= TS_POLLING;
cx->usage++;
acpi_state_timer_broadcast(pr, cx, 0);
- cx->time += ticks_elapsed(t1, t2);
+ cx->time += sleep_ticks;
return ticks_elapsed_in_us(t1, t2);
}
struct acpi_processor *pr;
struct acpi_processor_cx *cx = cpuidle_get_statedata(state);
u32 t1, t2;
+ int sleep_ticks = 0;
+
pr = processors[smp_processor_id()];
if (unlikely(!pr))
if (acpi_idle_suspend)
return(acpi_idle_enter_c1(dev, state));
+ if (acpi_idle_bm_check()) {
+ if (dev->safe_state) {
+ return dev->safe_state->enter(dev, dev->safe_state);
+ } else {
+ acpi_safe_halt();
+ return 0;
+ }
+ }
+
local_irq_disable();
current_thread_info()->status &= ~TS_POLLING;
/*
return 0;
}
+ /* Tell the scheduler that we are going deep-idle: */
+ sched_clock_idle_sleep_event();
/*
* Must be done before busmaster disable as we might need to
* access HPET !
*/
acpi_state_timer_broadcast(pr, cx, 1);
- if (acpi_idle_bm_check()) {
- cx = pr->power.bm_state;
-
- acpi_idle_update_bm_rld(pr, cx);
-
- t1 = inl(acpi_gbl_FADT.xpm_timer_block.address);
- acpi_idle_do_entry(cx);
- t2 = inl(acpi_gbl_FADT.xpm_timer_block.address);
- } else {
- acpi_idle_update_bm_rld(pr, cx);
+ acpi_idle_update_bm_rld(pr, cx);
+ /*
+ * disable bus master
+ * bm_check implies we need ARB_DIS
+ * !bm_check implies we need cache flush
+ * bm_control implies whether we can do ARB_DIS
+ *
+ * That leaves a case where bm_check is set and bm_control is
+ * not set. In that case we cannot do much, we enter C3
+ * without doing anything.
+ */
+ if (pr->flags.bm_check && pr->flags.bm_control) {
spin_lock(&c3_lock);
c3_cpu_count++;
/* Disable bus master arbitration when all CPUs are in C3 */
if (c3_cpu_count == num_online_cpus())
acpi_set_register(ACPI_BITREG_ARB_DISABLE, 1);
spin_unlock(&c3_lock);
+ } else if (!pr->flags.bm_check) {
+ ACPI_FLUSH_CPU_CACHE();
+ }
- t1 = inl(acpi_gbl_FADT.xpm_timer_block.address);
- acpi_idle_do_entry(cx);
- t2 = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ t1 = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ acpi_idle_do_entry(cx);
+ t2 = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ /* Re-enable bus master arbitration */
+ if (pr->flags.bm_check && pr->flags.bm_control) {
spin_lock(&c3_lock);
- /* Re-enable bus master arbitration */
- if (c3_cpu_count == num_online_cpus())
- acpi_set_register(ACPI_BITREG_ARB_DISABLE, 0);
+ acpi_set_register(ACPI_BITREG_ARB_DISABLE, 0);
c3_cpu_count--;
spin_unlock(&c3_lock);
}
/* TSC could halt in idle, so notify users */
mark_tsc_unstable("TSC halts in idle");
#endif
+ sleep_ticks = ticks_elapsed(t1, t2);
+ /* Tell the scheduler how much we idled: */
+ sched_clock_idle_wakeup_event(sleep_ticks*PM_TIMER_TICK_NS);
local_irq_enable();
current_thread_info()->status |= TS_POLLING;
cx->usage++;
acpi_state_timer_broadcast(pr, cx, 0);
- cx->time += ticks_elapsed(t1, t2);
+ cx->time += sleep_ticks;
return ticks_elapsed_in_us(t1, t2);
}
case ACPI_STATE_C1:
state->flags |= CPUIDLE_FLAG_SHALLOW;
state->enter = acpi_idle_enter_c1;
+ dev->safe_state = state;
break;
case ACPI_STATE_C2:
state->flags |= CPUIDLE_FLAG_BALANCED;
state->flags |= CPUIDLE_FLAG_TIME_VALID;
state->enter = acpi_idle_enter_simple;
+ dev->safe_state = state;
break;
case ACPI_STATE_C3:
if (!count)
return -EINVAL;
- /* find the deepest state that can handle active BM */
- if (pr->flags.bm_check) {
- for (i = 1; i < ACPI_PROCESSOR_MAX_POWER && i <= max_cstate; i++)
- if (pr->power.states[i].type == ACPI_STATE_C3)
- break;
- pr->power.bm_state = &pr->power.states[i-1];
- }
-
return 0;
}
int acpi_processor_tstate_has_changed(struct acpi_processor *pr)
{
- return acpi_processor_get_platform_limit(pr);
+ int result = 0;
+ int throttling_limit;
+ int current_state;
+ struct acpi_processor_limit *limit;
+ int target_state;
+
+ result = acpi_processor_get_platform_limit(pr);
+ if (result) {
+ /* Throttling Limit is unsupported */
+ return result;
+ }
+
+ throttling_limit = pr->throttling_platform_limit;
+ if (throttling_limit >= pr->throttling.state_count) {
+ /* Uncorrect Throttling Limit */
+ return -EINVAL;
+ }
+
+ current_state = pr->throttling.state;
+ if (current_state > throttling_limit) {
+ /*
+ * The current state can meet the requirement of
+ * _TPC limit. But it is reasonable that OSPM changes
+ * t-states from high to low for better performance.
+ * Of course the limit condition of thermal
+ * and user should be considered.
+ */
+ limit = &pr->limit;
+ target_state = throttling_limit;
+ if (limit->thermal.tx > target_state)
+ target_state = limit->thermal.tx;
+ if (limit->user.tx > target_state)
+ target_state = limit->user.tx;
+ } else if (current_state == throttling_limit) {
+ /*
+ * Unnecessary to change the throttling state
+ */
+ return 0;
+ } else {
+ /*
+ * If the current state is lower than the limit of _TPC, it
+ * will be forced to switch to the throttling state defined
+ * by throttling_platfor_limit.
+ * Because the previous state meets with the limit condition
+ * of thermal and user, it is unnecessary to check it again.
+ */
+ target_state = throttling_limit;
+ }
+ return acpi_processor_set_throttling(pr, target_state);
}
/*
struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
union acpi_object *ptc = NULL;
union acpi_object obj = { 0 };
+ struct acpi_processor_throttling *throttling;
status = acpi_evaluate_object(pr->handle, "_PTC", NULL, &buffer);
if (ACPI_FAILURE(status)) {
memcpy(&pr->throttling.status_register, obj.buffer.pointer,
sizeof(struct acpi_ptc_register));
+ throttling = &pr->throttling;
+
+ if ((throttling->control_register.bit_width +
+ throttling->control_register.bit_offset) > 32) {
+ printk(KERN_ERR PREFIX "Invalid _PTC control register\n");
+ result = -EFAULT;
+ goto end;
+ }
+
+ if ((throttling->status_register.bit_width +
+ throttling->status_register.bit_offset) > 32) {
+ printk(KERN_ERR PREFIX "Invalid _PTC status register\n");
+ result = -EFAULT;
+ goto end;
+ }
+
end:
kfree(buffer.pointer);
return 0;
}
-static int acpi_read_throttling_status(struct acpi_processor_throttling
- *throttling)
+#ifdef CONFIG_X86
+static int acpi_throttling_rdmsr(struct acpi_processor *pr,
+ acpi_integer * value)
{
- int value = -1;
+ struct cpuinfo_x86 *c;
+ u64 msr_high, msr_low;
+ unsigned int cpu;
+ u64 msr = 0;
+ int ret = -1;
+
+ cpu = pr->id;
+ c = &cpu_data(cpu);
+
+ if ((c->x86_vendor != X86_VENDOR_INTEL) ||
+ !cpu_has(c, X86_FEATURE_ACPI)) {
+ printk(KERN_ERR PREFIX
+ "HARDWARE addr space,NOT supported yet\n");
+ } else {
+ msr_low = 0;
+ msr_high = 0;
+ rdmsr_on_cpu(cpu, MSR_IA32_THERM_CONTROL,
+ (u32 *)&msr_low , (u32 *) &msr_high);
+ msr = (msr_high << 32) | msr_low;
+ *value = (acpi_integer) msr;
+ ret = 0;
+ }
+ return ret;
+}
+
+static int acpi_throttling_wrmsr(struct acpi_processor *pr, acpi_integer value)
+{
+ struct cpuinfo_x86 *c;
+ unsigned int cpu;
+ int ret = -1;
+ u64 msr;
+
+ cpu = pr->id;
+ c = &cpu_data(cpu);
+
+ if ((c->x86_vendor != X86_VENDOR_INTEL) ||
+ !cpu_has(c, X86_FEATURE_ACPI)) {
+ printk(KERN_ERR PREFIX
+ "HARDWARE addr space,NOT supported yet\n");
+ } else {
+ msr = value;
+ wrmsr_on_cpu(cpu, MSR_IA32_THERM_CONTROL,
+ msr & 0xffffffff, msr >> 32);
+ ret = 0;
+ }
+ return ret;
+}
+#else
+static int acpi_throttling_rdmsr(struct acpi_processor *pr,
+ acpi_integer * value)
+{
+ printk(KERN_ERR PREFIX
+ "HARDWARE addr space,NOT supported yet\n");
+ return -1;
+}
+
+static int acpi_throttling_wrmsr(struct acpi_processor *pr, acpi_integer value)
+{
+ printk(KERN_ERR PREFIX
+ "HARDWARE addr space,NOT supported yet\n");
+ return -1;
+}
+#endif
+
+static int acpi_read_throttling_status(struct acpi_processor *pr,
+ acpi_integer *value)
+{
+ u32 bit_width, bit_offset;
+ u64 ptc_value;
+ u64 ptc_mask;
+ struct acpi_processor_throttling *throttling;
+ int ret = -1;
+
+ throttling = &pr->throttling;
switch (throttling->status_register.space_id) {
case ACPI_ADR_SPACE_SYSTEM_IO:
+ ptc_value = 0;
+ bit_width = throttling->status_register.bit_width;
+ bit_offset = throttling->status_register.bit_offset;
+
acpi_os_read_port((acpi_io_address) throttling->status_register.
- address, &value,
- (u32) throttling->status_register.bit_width *
- 8);
+ address, (u32 *) &ptc_value,
+ (u32) (bit_width + bit_offset));
+ ptc_mask = (1 << bit_width) - 1;
+ *value = (acpi_integer) ((ptc_value >> bit_offset) & ptc_mask);
+ ret = 0;
break;
case ACPI_ADR_SPACE_FIXED_HARDWARE:
- printk(KERN_ERR PREFIX
- "HARDWARE addr space,NOT supported yet\n");
+ ret = acpi_throttling_rdmsr(pr, value);
break;
default:
printk(KERN_ERR PREFIX "Unknown addr space %d\n",
(u32) (throttling->status_register.space_id));
}
- return value;
+ return ret;
}
-static int acpi_write_throttling_state(struct acpi_processor_throttling
- *throttling, int value)
+static int acpi_write_throttling_state(struct acpi_processor *pr,
+ acpi_integer value)
{
+ u32 bit_width, bit_offset;
+ u64 ptc_value;
+ u64 ptc_mask;
+ struct acpi_processor_throttling *throttling;
int ret = -1;
+ throttling = &pr->throttling;
switch (throttling->control_register.space_id) {
case ACPI_ADR_SPACE_SYSTEM_IO:
+ bit_width = throttling->control_register.bit_width;
+ bit_offset = throttling->control_register.bit_offset;
+ ptc_mask = (1 << bit_width) - 1;
+ ptc_value = value & ptc_mask;
+
acpi_os_write_port((acpi_io_address) throttling->
- control_register.address, value,
- (u32) throttling->control_register.
- bit_width * 8);
+ control_register.address,
+ (u32) (ptc_value << bit_offset),
+ (u32) (bit_width + bit_offset));
ret = 0;
break;
case ACPI_ADR_SPACE_FIXED_HARDWARE:
- printk(KERN_ERR PREFIX
- "HARDWARE addr space,NOT supported yet\n");
+ ret = acpi_throttling_wrmsr(pr, value);
break;
default:
printk(KERN_ERR PREFIX "Unknown addr space %d\n",
return ret;
}
-static int acpi_get_throttling_state(struct acpi_processor *pr, int value)
+static int acpi_get_throttling_state(struct acpi_processor *pr,
+ acpi_integer value)
{
int i;
return i;
}
-static int acpi_get_throttling_value(struct acpi_processor *pr, int state)
+static int acpi_get_throttling_value(struct acpi_processor *pr,
+ int state, acpi_integer *value)
{
- int value = -1;
+ int ret = -1;
+
if (state >= 0 && state <= pr->throttling.state_count) {
struct acpi_processor_tx_tss *tx =
(struct acpi_processor_tx_tss *)&(pr->throttling.
states_tss[state]);
- value = tx->control;
+ *value = tx->control;
+ ret = 0;
}
- return value;
+ return ret;
}
static int acpi_processor_get_throttling_ptc(struct acpi_processor *pr)
{
int state = 0;
- u32 value = 0;
+ int ret;
+ acpi_integer value;
if (!pr)
return -EINVAL;
pr->throttling.state = 0;
local_irq_disable();
- value = acpi_read_throttling_status(&pr->throttling);
- if (value >= 0) {
+ value = 0;
+ ret = acpi_read_throttling_status(pr, &value);
+ if (ret >= 0) {
state = acpi_get_throttling_state(pr, value);
pr->throttling.state = state;
}
return pr->throttling.acpi_processor_get_throttling(pr);
}
+static int acpi_processor_get_fadt_info(struct acpi_processor *pr)
+{
+ int i, step;
+
+ if (!pr->throttling.address) {
+ ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling register\n"));
+ return -EINVAL;
+ } else if (!pr->throttling.duty_width) {
+ ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling states\n"));
+ return -EINVAL;
+ }
+ /* TBD: Support duty_cycle values that span bit 4. */
+ else if ((pr->throttling.duty_offset + pr->throttling.duty_width) > 4) {
+ printk(KERN_WARNING PREFIX "duty_cycle spans bit 4\n");
+ return -EINVAL;
+ }
+
+ pr->throttling.state_count = 1 << acpi_gbl_FADT.duty_width;
+
+ /*
+ * Compute state values. Note that throttling displays a linear power
+ * performance relationship (at 50% performance the CPU will consume
+ * 50% power). Values are in 1/10th of a percent to preserve accuracy.
+ */
+
+ step = (1000 / pr->throttling.state_count);
+
+ for (i = 0; i < pr->throttling.state_count; i++) {
+ pr->throttling.states[i].performance = 1000 - step * i;
+ pr->throttling.states[i].power = 1000 - step * i;
+ }
+ return 0;
+}
+
static int acpi_processor_set_throttling_fadt(struct acpi_processor *pr,
int state)
{
static int acpi_processor_set_throttling_ptc(struct acpi_processor *pr,
int state)
{
- u32 value = 0;
+ int ret;
+ acpi_integer value;
if (!pr)
return -EINVAL;
return -EPERM;
local_irq_disable();
-
- value = acpi_get_throttling_value(pr, state);
- if (value >= 0) {
- acpi_write_throttling_state(&pr->throttling, value);
+ value = 0;
+ ret = acpi_get_throttling_value(pr, state, &value);
+ if (ret >= 0) {
+ acpi_write_throttling_state(pr, value);
pr->throttling.state = state;
}
local_irq_enable();
int acpi_processor_get_throttling_info(struct acpi_processor *pr)
{
int result = 0;
- int step = 0;
- int i = 0;
ACPI_DEBUG_PRINT((ACPI_DB_INFO,
"pblk_address[0x%08x] duty_offset[%d] duty_width[%d]\n",
acpi_processor_get_throttling_states(pr) ||
acpi_processor_get_platform_limit(pr))
{
+ if (acpi_processor_get_fadt_info(pr))
+ return 0;
pr->throttling.acpi_processor_get_throttling =
&acpi_processor_get_throttling_fadt;
pr->throttling.acpi_processor_set_throttling =
acpi_processor_get_tsd(pr);
- if (!pr->throttling.address) {
- ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling register\n"));
- return 0;
- } else if (!pr->throttling.duty_width) {
- ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No throttling states\n"));
- return 0;
- }
- /* TBD: Support duty_cycle values that span bit 4. */
- else if ((pr->throttling.duty_offset + pr->throttling.duty_width) > 4) {
- printk(KERN_WARNING PREFIX "duty_cycle spans bit 4\n");
- return 0;
- }
-
/*
* PIIX4 Errata: We don't support throttling on the original PIIX4.
* This shouldn't be an issue as few (if any) mobile systems ever
return 0;
}
- pr->throttling.state_count = 1 << acpi_gbl_FADT.duty_width;
-
- /*
- * Compute state values. Note that throttling displays a linear power/
- * performance relationship (at 50% performance the CPU will consume
- * 50% power). Values are in 1/10th of a percent to preserve accuracy.
- */
-
- step = (1000 / pr->throttling.state_count);
-
- for (i = 0; i < pr->throttling.state_count; i++) {
- pr->throttling.states[i].performance = step * i;
- pr->throttling.states[i].power = step * i;
- }
-
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Found %d throttling states\n",
pr->throttling.state_count));
#include <linux/moduleparam.h>
#include <linux/kernel.h>
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <asm/uaccess.h>
struct acpi_battery {
struct power_supply bat;
struct acpi_sbs *sbs;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
struct proc_dir_entry *proc_entry;
#endif
unsigned long update_time;
u16 spec;
u8 id;
u8 present:1;
+ u8 have_sysfs_alarm:1;
};
#define to_acpi_battery(x) container_of(x, struct acpi_battery, bat);
struct acpi_device *device;
struct acpi_smb_hc *hc;
struct mutex lock;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
struct proc_dir_entry *charger_entry;
#endif
struct acpi_battery battery[MAX_SBS_BAT];
FS Interface (/proc/acpi)
-------------------------------------------------------------------------- */
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
/* Generic Routines */
static int
acpi_sbs_add_fs(struct proc_dir_entry **dir,
return result;
sprintf(battery->name, ACPI_BATTERY_DIR_NAME, id);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_sbs_add_fs(&battery->proc_entry, acpi_battery_dir,
battery->name, &acpi_battery_info_fops,
&acpi_battery_state_fops, &acpi_battery_alarm_fops,
}
battery->bat.get_property = acpi_sbs_battery_get_property;
result = power_supply_register(&sbs->device->dev, &battery->bat);
- device_create_file(battery->bat.dev, &alarm_attr);
+ if (result)
+ goto end;
+ result = device_create_file(battery->bat.dev, &alarm_attr);
+ if (result)
+ goto end;
+ battery->have_sysfs_alarm = 1;
+ end:
printk(KERN_INFO PREFIX "%s [%s]: Battery Slot [%s] (battery %s)\n",
ACPI_SBS_DEVICE_NAME, acpi_device_bid(sbs->device),
battery->name, sbs->battery->present ? "present" : "absent");
static void acpi_battery_remove(struct acpi_sbs *sbs, int id)
{
- if (sbs->battery[id].bat.dev)
- device_remove_file(sbs->battery[id].bat.dev, &alarm_attr);
- power_supply_unregister(&sbs->battery[id].bat);
-#ifdef CONFIG_ACPI_PROCFS
- if (sbs->battery[id].proc_entry) {
- acpi_sbs_remove_fs(&(sbs->battery[id].proc_entry),
- acpi_battery_dir);
+ struct acpi_battery *battery = &sbs->battery[id];
+
+ if (battery->bat.dev) {
+ if (battery->have_sysfs_alarm)
+ device_remove_file(battery->bat.dev, &alarm_attr);
+ power_supply_unregister(&battery->bat);
}
+#ifdef CONFIG_ACPI_PROCFS_POWER
+ if (battery->proc_entry)
+ acpi_sbs_remove_fs(&battery->proc_entry, acpi_battery_dir);
#endif
}
result = acpi_ac_get_present(sbs);
if (result)
goto end;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
result = acpi_sbs_add_fs(&sbs->charger_entry, acpi_ac_dir,
ACPI_AC_DIR_NAME, NULL,
&acpi_ac_state_fops, NULL, sbs);
{
if (sbs->charger.dev)
power_supply_unregister(&sbs->charger);
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
if (sbs->charger_entry)
acpi_sbs_remove_fs(&sbs->charger_entry, acpi_ac_dir);
#endif
static void acpi_sbs_rmdirs(void)
{
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
if (acpi_ac_dir) {
acpi_unlock_ac_dir(acpi_ac_dir);
acpi_ac_dir = NULL;
if (acpi_disabled)
return -ENODEV;
-#ifdef CONFIG_ACPI_PROCFS
+#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_dir = acpi_lock_ac_dir();
if (!acpi_ac_dir)
return -ENODEV;
/* XSDT has NULL entry, RSDT is used */
address = rsdt_address;
table_entry_size = sizeof(u32);
- ACPI_WARNING((AE_INFO, "BIOS XSDT has NULL entry,"
+ ACPI_WARNING((AE_INFO, "BIOS XSDT has NULL entry, "
"using RSDT"));
}
}
#include <linux/init.h>
#include <linux/types.h>
#include <linux/list.h>
+#include <linux/mutex.h>
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#include <linux/input.h>
u8 attached_count;
struct acpi_video_bus_cap cap;
struct acpi_video_bus_flags flags;
- struct semaphore sem;
struct list_head video_device_list;
+ struct mutex device_list_lock; /* protects video_device_list */
struct proc_dir_entry *dir;
struct input_dev *input;
char phys[32]; /* for input device */
{
struct seq_file *m = file->private_data;
struct acpi_video_device *dev = m->private;
- char str[4] = { 0 };
+ char str[5] = { 0 };
unsigned int level = 0;
int i;
return -ENODEV;
}
- down(&video->sem);
+ mutex_lock(&video->device_list_lock);
list_add_tail(&data->entry, &video->video_device_list);
- up(&video->sem);
+ mutex_unlock(&video->device_list_lock);
acpi_video_device_add_fs(device);
static void acpi_video_device_rebind(struct acpi_video_bus *video)
{
- struct list_head *node, *next;
- list_for_each_safe(node, next, &video->video_device_list) {
- struct acpi_video_device *dev =
- container_of(node, struct acpi_video_device, entry);
+ struct acpi_video_device *dev;
+
+ mutex_lock(&video->device_list_lock);
+
+ list_for_each_entry(dev, &video->video_device_list, entry)
acpi_video_device_bind(video, dev);
- }
+
+ mutex_unlock(&video->device_list_lock);
}
/*
static int acpi_video_switch_output(struct acpi_video_bus *video, int event)
{
- struct list_head *node, *next;
+ struct list_head *node;
struct acpi_video_device *dev = NULL;
struct acpi_video_device *dev_next = NULL;
struct acpi_video_device *dev_prev = NULL;
unsigned long state;
int status = 0;
+ mutex_lock(&video->device_list_lock);
- list_for_each_safe(node, next, &video->video_device_list) {
+ list_for_each(node, &video->video_device_list) {
dev = container_of(node, struct acpi_video_device, entry);
status = acpi_video_device_get_state(dev, &state);
if (state & 0x2) {
- dev_next =
- container_of(node->next, struct acpi_video_device,
- entry);
- dev_prev =
- container_of(node->prev, struct acpi_video_device,
- entry);
+ dev_next = container_of(node->next,
+ struct acpi_video_device, entry);
+ dev_prev = container_of(node->prev,
+ struct acpi_video_device, entry);
goto out;
}
}
+
dev_next = container_of(node->next, struct acpi_video_device, entry);
dev_prev = container_of(node->prev, struct acpi_video_device, entry);
- out:
+
+ out:
+ mutex_unlock(&video->device_list_lock);
+
switch (event) {
case ACPI_VIDEO_NOTIFY_CYCLE:
case ACPI_VIDEO_NOTIFY_NEXT_OUTPUT:
struct acpi_device *device)
{
int status = 0;
- struct list_head *node, *next;
-
+ struct acpi_device *dev;
acpi_video_device_enumerate(video);
- list_for_each_safe(node, next, &device->children) {
- struct acpi_device *dev =
- list_entry(node, struct acpi_device, node);
-
- if (!dev)
- continue;
+ list_for_each_entry(dev, &device->children, node) {
status = acpi_video_bus_get_one_device(dev, video);
if (ACPI_FAILURE(status)) {
ACPI_EXCEPTION((AE_INFO, status, "Cant attach device"));
continue;
}
-
}
return status;
}
video = device->video;
- down(&video->sem);
- list_del(&device->entry);
- up(&video->sem);
acpi_video_device_remove_fs(device->dev);
status = acpi_remove_notify_handler(device->dev->handle,
acpi_video_device_notify);
backlight_device_unregister(device->backlight);
video_output_unregister(device->output_dev);
+
return 0;
}
static int acpi_video_bus_put_devices(struct acpi_video_bus *video)
{
int status;
- struct list_head *node, *next;
+ struct acpi_video_device *dev, *next;
+ mutex_lock(&video->device_list_lock);
- list_for_each_safe(node, next, &video->video_device_list) {
- struct acpi_video_device *data =
- list_entry(node, struct acpi_video_device, entry);
- if (!data)
- continue;
+ list_for_each_entry_safe(dev, next, &video->video_device_list, entry) {
- status = acpi_video_bus_put_one_device(data);
+ status = acpi_video_bus_put_one_device(dev);
if (ACPI_FAILURE(status))
printk(KERN_WARNING PREFIX
"hhuuhhuu bug in acpi video driver.\n");
- if (data->brightness)
- kfree(data->brightness->levels);
- kfree(data->brightness);
- kfree(data);
+ if (dev->brightness) {
+ kfree(dev->brightness->levels);
+ kfree(dev->brightness);
+ }
+ list_del(&dev->entry);
+ kfree(dev);
}
+ mutex_unlock(&video->device_list_lock);
+
return 0;
}
struct input_dev *input;
int keycode;
-
- printk("video bus notify\n");
-
if (!video)
return;
static int instance;
static int acpi_video_bus_add(struct acpi_device *device)
{
- int result = 0;
- acpi_status status = 0;
- struct acpi_video_bus *video = NULL;
+ acpi_status status;
+ struct acpi_video_bus *video;
struct input_dev *input;
-
-
- if (!device)
- return -EINVAL;
+ int error;
video = kzalloc(sizeof(struct acpi_video_bus), GFP_KERNEL);
if (!video)
acpi_driver_data(device) = video;
acpi_video_bus_find_cap(video);
- result = acpi_video_bus_check(video);
- if (result)
- goto end;
+ error = acpi_video_bus_check(video);
+ if (error)
+ goto err_free_video;
- result = acpi_video_bus_add_fs(device);
- if (result)
- goto end;
+ error = acpi_video_bus_add_fs(device);
+ if (error)
+ goto err_free_video;
- init_MUTEX(&video->sem);
+ mutex_init(&video->device_list_lock);
INIT_LIST_HEAD(&video->video_device_list);
acpi_video_bus_get_devices(video, device);
if (ACPI_FAILURE(status)) {
ACPI_DEBUG_PRINT((ACPI_DB_ERROR,
"Error installing notify handler\n"));
- acpi_video_bus_stop_devices(video);
- acpi_video_bus_put_devices(video);
- kfree(video->attached_array);
- acpi_video_bus_remove_fs(device);
- result = -ENODEV;
- goto end;
+ error = -ENODEV;
+ goto err_stop_video;
}
-
video->input = input = input_allocate_device();
+ if (!input) {
+ error = -ENOMEM;
+ goto err_uninstall_notify;
+ }
snprintf(video->phys, sizeof(video->phys),
"%s/video/input0", acpi_device_hid(video->device));
input->phys = video->phys;
input->id.bustype = BUS_HOST;
input->id.product = 0x06;
+ input->dev.parent = &device->dev;
input->evbit[0] = BIT(EV_KEY);
set_bit(KEY_SWITCHVIDEOMODE, input->keybit);
set_bit(KEY_VIDEO_NEXT, input->keybit);
set_bit(KEY_BRIGHTNESS_ZERO, input->keybit);
set_bit(KEY_DISPLAY_OFF, input->keybit);
set_bit(KEY_UNKNOWN, input->keybit);
- result = input_register_device(input);
- if (result) {
- acpi_remove_notify_handler(video->device->handle,
- ACPI_DEVICE_NOTIFY,
- acpi_video_bus_notify);
- acpi_video_bus_stop_devices(video);
- acpi_video_bus_put_devices(video);
- kfree(video->attached_array);
- acpi_video_bus_remove_fs(device);
- goto end;
- }
+ error = input_register_device(input);
+ if (error)
+ goto err_free_input_dev;
printk(KERN_INFO PREFIX "%s [%s] (multi-head: %s rom: %s post: %s)\n",
ACPI_VIDEO_DEVICE_NAME, acpi_device_bid(device),
video->flags.rom ? "yes" : "no",
video->flags.post ? "yes" : "no");
- end:
- if (result)
- kfree(video);
+ return 0;
+
+ err_free_input_dev:
+ input_free_device(input);
+ err_uninstall_notify:
+ acpi_remove_notify_handler(device->handle, ACPI_DEVICE_NOTIFY,
+ acpi_video_bus_notify);
+ err_stop_video:
+ acpi_video_bus_stop_devices(video);
+ acpi_video_bus_put_devices(video);
+ kfree(video->attached_array);
+ acpi_video_bus_remove_fs(device);
+ err_free_video:
+ kfree(video);
+ acpi_driver_data(device) = NULL;
- return result;
+ return error;
}
static int acpi_video_bus_remove(struct acpi_device *device, int type)
PIIX_80C_SEC = (1 << 7) | (1 << 6),
/* controller IDs */
- piix_pata_33 = 0, /* PIIX4 at 33Mhz */
- ich_pata_33 = 1, /* ICH up to UDMA 33 only */
- ich_pata_66 = 2, /* ICH up to 66 Mhz */
- ich_pata_100 = 3, /* ICH up to UDMA 100 */
- ich5_sata = 5,
- ich6_sata = 6,
- ich6_sata_ahci = 7,
- ich6m_sata_ahci = 8,
- ich8_sata_ahci = 9,
- piix_pata_mwdma = 10, /* PIIX3 MWDMA only */
- tolapai_sata_ahci = 11,
- ich9_2port_sata = 12,
+ piix_pata_mwdma = 0, /* PIIX3 MWDMA only */
+ piix_pata_33, /* PIIX4 at 33Mhz */
+ ich_pata_33, /* ICH up to UDMA 33 only */
+ ich_pata_66, /* ICH up to 66 Mhz */
+ ich_pata_100, /* ICH up to UDMA 100 */
+ ich5_sata,
+ ich6_sata,
+ ich6_sata_ahci,
+ ich6m_sata_ahci,
+ ich8_sata_ahci,
+ ich8_2port_sata,
+ ich8m_apple_sata_ahci, /* locks up on second port enable */
+ tolapai_sata_ahci,
/* constants for mapping table */
P0 = 0, /* port 0 */
/* SATA Controller 1 IDE (ICH8) */
{ 0x8086, 0x2820, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller 2 IDE (ICH8) */
- { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x2825, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* Mobile SATA Controller IDE (ICH8M) */
{ 0x8086, 0x2828, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
+ /* Mobile SATA Controller IDE (ICH8M), Apple */
+ { 0x8086, 0x2828, 0x106b, 0x00a0, 0, 0, ich8m_apple_sata_ahci },
/* SATA Controller IDE (ICH9) */
{ 0x8086, 0x2920, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller IDE (ICH9) */
- { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x2921, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (ICH9) */
- { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x2926, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (ICH9M) */
- { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x2928, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (ICH9M) */
- { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich9_2port_sata },
+ { 0x8086, 0x292d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_2port_sata },
/* SATA Controller IDE (ICH9M) */
{ 0x8086, 0x292e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, ich8_sata_ahci },
/* SATA Controller IDE (Tolapai) */
static const struct piix_map_db ich8_map_db = {
.mask = 0x3,
- .port_enable = 0x3,
+ .port_enable = 0xf,
.map = {
/* PM PS SM SS MAP */
{ P0, P2, P1, P3 }, /* 00b (hardwired when in AHCI) */
},
};
-static const struct piix_map_db tolapai_map_db = {
+static const struct piix_map_db ich8_2port_map_db = {
.mask = 0x3,
.port_enable = 0x3,
.map = {
},
};
-static const struct piix_map_db ich9_2port_map_db = {
+static const struct piix_map_db ich8m_apple_map_db = {
+ .mask = 0x3,
+ .port_enable = 0x1,
+ .map = {
+ /* PM PS SM SS MAP */
+ { P0, NA, NA, NA }, /* 00b */
+ { RV, RV, RV, RV },
+ { P0, P2, IDE, IDE }, /* 10b */
+ { RV, RV, RV, RV },
+ },
+};
+
+static const struct piix_map_db tolapai_map_db = {
.mask = 0x3,
.port_enable = 0x3,
.map = {
[ich6_sata_ahci] = &ich6_map_db,
[ich6m_sata_ahci] = &ich6m_map_db,
[ich8_sata_ahci] = &ich8_map_db,
+ [ich8_2port_sata] = &ich8_2port_map_db,
+ [ich8m_apple_sata_ahci] = &ich8m_apple_map_db,
[tolapai_sata_ahci] = &tolapai_map_db,
- [ich9_2port_sata] = &ich9_2port_map_db,
};
static struct ata_port_info piix_port_info[] = {
+ [piix_pata_mwdma] = /* PIIX3 MWDMA only */
+ {
+ .sht = &piix_sht,
+ .flags = PIIX_PATA_FLAGS,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
+ .port_ops = &piix_pata_ops,
+ },
+
[piix_pata_33] = /* PIIX4 at 33MHz */
{
.sht = &piix_sht,
.port_ops = &piix_sata_ops,
},
- [piix_pata_mwdma] = /* PIIX3 MWDMA only */
+ [ich8_2port_sata] =
{
.sht = &piix_sht,
- .flags = PIIX_PATA_FLAGS,
+ .flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
+ PIIX_FLAG_AHCI,
.pio_mask = 0x1f, /* pio0-4 */
- .mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
- .port_ops = &piix_pata_ops,
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &piix_sata_ops,
},
[tolapai_sata_ahci] =
.port_ops = &piix_sata_ops,
},
- [ich9_2port_sata] =
+ [ich8m_apple_sata_ahci] =
{
.sht = &piix_sht,
.flags = PIIX_SATA_FLAGS | PIIX_FLAG_SCR |
.udma_mask = ATA_UDMA6,
.port_ops = &piix_sata_ops,
},
+
};
static struct pci_bits piix_enable_bits[] = {
DMI_MATCH(DMI_PRODUCT_NAME, "Satellite U205"),
},
},
+ {
+ .ident = "SATELLITE U205",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "SATELLITE U205"),
+ },
+ },
{
.ident = "Portege M500",
.matches = {
if (!mmio)
return -ENOMEM;
- tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ tmp = ioread32(mmio + AHCI_GLOBAL_CTL);
if (tmp & AHCI_ENABLE) {
tmp &= ~AHCI_ENABLE;
- writel(tmp, mmio + AHCI_GLOBAL_CTL);
+ iowrite32(tmp, mmio + AHCI_GLOBAL_CTL);
- tmp = readl(mmio + AHCI_GLOBAL_CTL);
+ tmp = ioread32(mmio + AHCI_GLOBAL_CTL);
if (tmp & AHCI_ENABLE)
rc = -EIO;
}
* Hardware documentation available from http://www.t13.org/ and
* http://www.sata-io.org/
*
+ * Standards documents from:
+ * http://www.t13.org (ATA standards, PCI DMA IDE spec)
+ * http://www.t10.org (SCSI MMC - for ATAPI MMC)
+ * http://www.sata-io.org (SATA)
+ * http://www.compactflash.org (CF)
+ * http://www.qic.org (QIC157 - Tape and DSC)
+ * http://www.ce-ata.org (CE-ATA: not supported)
+ *
*/
#include <linux/kernel.h>
}
if ((dev->class == ATA_DEV_ATAPI) &&
- (atapi_command_packet_set(id) == TYPE_TAPE))
+ (atapi_command_packet_set(id) == TYPE_TAPE)) {
dev->max_sectors = ATA_MAX_SECTORS_TAPE;
+ dev->horkage |= ATA_HORKAGE_STUCK_ERR;
+ }
if (dev->horkage & ATA_HORKAGE_MAX_SEC_128)
dev->max_sectors = min_t(unsigned int, ATA_MAX_SECTORS_128,
}
}
-/**
- * __sata_phy_reset - Wake/reset a low-level SATA PHY
- * @ap: SATA port associated with target SATA PHY.
- *
- * This function issues commands to standard SATA Sxxx
- * PHY registers, to wake up the phy (and device), and
- * clear any reset condition.
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- *
- */
-void __sata_phy_reset(struct ata_port *ap)
-{
- struct ata_link *link = &ap->link;
- unsigned long timeout = jiffies + (HZ * 5);
- u32 sstatus;
-
- if (ap->flags & ATA_FLAG_SATA_RESET) {
- /* issue phy wake/reset */
- sata_scr_write_flush(link, SCR_CONTROL, 0x301);
- /* Couldn't find anything in SATA I/II specs, but
- * AHCI-1.1 10.4.2 says at least 1 ms. */
- mdelay(1);
- }
- /* phy wake/clear reset */
- sata_scr_write_flush(link, SCR_CONTROL, 0x300);
-
- /* wait for phy to become ready, if necessary */
- do {
- msleep(200);
- sata_scr_read(link, SCR_STATUS, &sstatus);
- if ((sstatus & 0xf) != 1)
- break;
- } while (time_before(jiffies, timeout));
-
- /* print link status */
- sata_print_link_status(link);
-
- /* TODO: phy layer with polling, timeouts, etc. */
- if (!ata_link_offline(link))
- ata_port_probe(ap);
- else
- ata_port_disable(ap);
-
- if (ap->flags & ATA_FLAG_DISABLED)
- return;
-
- if (ata_busy_sleep(ap, ATA_TMOUT_BOOT_QUICK, ATA_TMOUT_BOOT)) {
- ata_port_disable(ap);
- return;
- }
-
- ap->cbl = ATA_CBL_SATA;
-}
-
-/**
- * sata_phy_reset - Reset SATA bus.
- * @ap: SATA port associated with target SATA PHY.
- *
- * This function resets the SATA bus, and then probes
- * the bus for devices.
- *
- * LOCKING:
- * PCI/etc. bus probe sem.
- *
- */
-void sata_phy_reset(struct ata_port *ap)
-{
- __sata_phy_reset(ap);
- if (ap->flags & ATA_FLAG_DISABLED)
- return;
- ata_bus_reset(ap);
-}
-
/**
* ata_dev_pair - return other device on cable
* @adev: device
* let the EH abort the command or reset the device.
*/
if (unlikely(status & (ATA_ERR | ATA_DF))) {
- ata_port_printk(ap, KERN_WARNING, "DRQ=1 with device "
- "error, dev_stat 0x%X\n", status);
- qc->err_mask |= AC_ERR_HSM;
- ap->hsm_task_state = HSM_ST_ERR;
- goto fsm_start;
+ /* Some ATAPI tape drives forget to clear the ERR bit
+ * when doing the next command (mostly request sense).
+ * We ignore ERR here to workaround and proceed sending
+ * the CDB.
+ */
+ if (!(qc->dev->horkage & ATA_HORKAGE_STUCK_ERR)) {
+ ata_port_printk(ap, KERN_WARNING,
+ "DRQ=1 with device error, "
+ "dev_stat 0x%X\n", status);
+ qc->err_mask |= AC_ERR_HSM;
+ ap->hsm_task_state = HSM_ST_ERR;
+ goto fsm_start;
+ }
}
/* Send the CDB (atapi) or the first data block (ata pio out).
EXPORT_SYMBOL_GPL(sata_set_spd);
EXPORT_SYMBOL_GPL(sata_link_debounce);
EXPORT_SYMBOL_GPL(sata_link_resume);
-EXPORT_SYMBOL_GPL(sata_phy_reset);
-EXPORT_SYMBOL_GPL(__sata_phy_reset);
EXPORT_SYMBOL_GPL(ata_bus_reset);
EXPORT_SYMBOL_GPL(ata_std_prereset);
EXPORT_SYMBOL_GPL(ata_std_softreset);
#ifdef CONFIG_PCI
EXPORT_SYMBOL_GPL(ata_port_pbar_desc);
#endif /* CONFIG_PCI */
-EXPORT_SYMBOL_GPL(ata_eng_timeout);
EXPORT_SYMBOL_GPL(ata_port_schedule_eh);
EXPORT_SYMBOL_GPL(ata_link_abort);
EXPORT_SYMBOL_GPL(ata_port_abort);
}
}
-/**
- * ata_qc_timeout - Handle timeout of queued command
- * @qc: Command that timed out
- *
- * Some part of the kernel (currently, only the SCSI layer)
- * has noticed that the active command on port @ap has not
- * completed after a specified length of time. Handle this
- * condition by disabling DMA (if necessary) and completing
- * transactions, with error if necessary.
- *
- * This also handles the case of the "lost interrupt", where
- * for some reason (possibly hardware bug, possibly driver bug)
- * an interrupt was not delivered to the driver, even though the
- * transaction completed successfully.
- *
- * TODO: kill this function once old EH is gone.
- *
- * LOCKING:
- * Inherited from SCSI layer (none, can sleep)
- */
-static void ata_qc_timeout(struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- u8 host_stat = 0, drv_stat;
- unsigned long flags;
-
- DPRINTK("ENTER\n");
-
- ap->hsm_task_state = HSM_ST_IDLE;
-
- spin_lock_irqsave(ap->lock, flags);
-
- switch (qc->tf.protocol) {
-
- case ATA_PROT_DMA:
- case ATA_PROT_ATAPI_DMA:
- host_stat = ap->ops->bmdma_status(ap);
-
- /* before we do anything else, clear DMA-Start bit */
- ap->ops->bmdma_stop(qc);
-
- /* fall through */
-
- default:
- ata_altstatus(ap);
- drv_stat = ata_chk_status(ap);
-
- /* ack bmdma irq events */
- ap->ops->irq_clear(ap);
-
- ata_dev_printk(qc->dev, KERN_ERR, "command 0x%x timeout, "
- "stat 0x%x host_stat 0x%x\n",
- qc->tf.command, drv_stat, host_stat);
-
- /* complete taskfile transaction */
- qc->err_mask |= AC_ERR_TIMEOUT;
- break;
- }
-
- spin_unlock_irqrestore(ap->lock, flags);
-
- ata_eh_qc_complete(qc);
-
- DPRINTK("EXIT\n");
-}
-
-/**
- * ata_eng_timeout - Handle timeout of queued command
- * @ap: Port on which timed-out command is active
- *
- * Some part of the kernel (currently, only the SCSI layer)
- * has noticed that the active command on port @ap has not
- * completed after a specified length of time. Handle this
- * condition by disabling DMA (if necessary) and completing
- * transactions, with error if necessary.
- *
- * This also handles the case of the "lost interrupt", where
- * for some reason (possibly hardware bug, possibly driver bug)
- * an interrupt was not delivered to the driver, even though the
- * transaction completed successfully.
- *
- * TODO: kill this function once old EH is gone.
- *
- * LOCKING:
- * Inherited from SCSI layer (none, can sleep)
- */
-void ata_eng_timeout(struct ata_port *ap)
-{
- DPRINTK("ENTER\n");
-
- ata_qc_timeout(ata_qc_from_tag(ap, ap->link.active_tag));
-
- DPRINTK("EXIT\n");
-}
-
static int ata_eh_nr_in_flight(struct ata_port *ap)
{
unsigned int tag;
if (!using_pio && ata_check_atapi_dma(qc))
using_pio = 1;
- /* Some controller variants snoop this value for Packet transfers
- to do state machine and FIFO management. Thus we want to set it
- properly, and for DMA where it is effectively meaningless */
+ /* Some controller variants snoop this value for Packet
+ * transfers to do state machine and FIFO management. Thus we
+ * want to set it properly, and for DMA where it is
+ * effectively meaningless.
+ */
nbytes = min(qc->nbytes, (unsigned int)63 * 1024);
+ /* Most ATAPI devices which honor transfer chunk size don't
+ * behave according to the spec when odd chunk size which
+ * matches the transfer length is specified. If the number of
+ * bytes to transfer is 2n+1. According to the spec, what
+ * should happen is to indicate that 2n+1 is going to be
+ * transferred and transfer 2n+2 bytes where the last byte is
+ * padding.
+ *
+ * In practice, this doesn't happen. ATAPI devices first
+ * indicate and transfer 2n bytes and then indicate and
+ * transfer 2 bytes where the last byte is padding.
+ *
+ * This inconsistency confuses several controllers which
+ * perform PIO using DMA such as Intel AHCIs and sil3124/32.
+ * These controllers use actual number of transferred bytes to
+ * update DMA poitner and transfer of 4n+2 bytes make those
+ * controller push DMA pointer by 4n+4 bytes because SATA data
+ * FISes are aligned to 4 bytes. This causes data corruption
+ * and buffer overrun.
+ *
+ * Always setting nbytes to even number solves this problem
+ * because then ATAPI devices don't have to split data at 2n
+ * boundaries.
+ */
+ if (nbytes & 0x1)
+ nbytes++;
+
qc->tf.lbam = (nbytes & 0xFF);
qc->tf.lbah = (nbytes >> 8);
xlat_func = NULL;
if (likely((scsi_op != ATA_16) || !atapi_passthru16)) {
/* relay SCSI command to ATAPI device */
- if (unlikely(scmd->cmd_len > dev->cdb_len))
+ int len = COMMAND_SIZE(scsi_op);
+ if (unlikely(len > scmd->cmd_len || len > dev->cdb_len))
goto bad_cdb_len;
xlat_func = atapi_xlat;
/* Fujitsu P2000 */
if (pdev->subsystem_vendor == 0x10CF && pdev->subsystem_device == 0x10AF)
return 1;
+ /* Mitac 8317 (Winbook-A) and relatives */
+ if (pdev->subsystem_vendor == 0x1071 && pdev->subsystem_device == 0x8317)
+ return 1;
/* Systems by DMI */
if (dmi_check_system(cable_dmi_table))
return 1;
adev->max_sectors = 255;
}
+/**
+ * ali_check_atapi_dma - DMA check for most ALi controllers
+ * @adev: Device
+ *
+ * Called to decide whether commands should be sent by DMA or PIO
+ */
+
+static int ali_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ /* If its not a media command, its not worth it */
+ if (qc->nbytes < 2048)
+ return -EOPNOTSUPP;
+ return 0;
+}
+
static struct scsi_host_template ali_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
+ .check_atapi_dma = ali_check_atapi_dma,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
+ .check_atapi_dma = ali_check_atapi_dma,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
unsigned short int_status = ATAPI_GET_INT_STATUS(base);
if (ATAPI_GET_STATUS(base) & (MULTI_XFER_ON|ULTRA_XFER_ON)) {
- host_stat = ATA_DMA_ACTIVE;
+ host_stat |= ATA_DMA_ACTIVE;
}
if (int_status & (MULTI_DONE_INT|UDMAIN_DONE_INT|UDMAOUT_DONE_INT)) {
- host_stat = ATA_DMA_INTR;
+ host_stat |= ATA_DMA_INTR;
}
if (int_status & (MULTI_TERM_INT|UDMAIN_TERM_INT|UDMAOUT_TERM_INT)) {
- host_stat = ATA_DMA_ERR;
+ host_stat |= ATA_DMA_ERR;
}
return host_stat;
/* Restore state */
pci_write_config_byte(pdev, 0x5B, scr2);
- if (ata66 & (1 << ap->port_no))
+ if (ata66 & (2 >> ap->port_no))
ap->cbl = ATA_CBL_PATA40;
else
ap->cbl = ATA_CBL_PATA80;
struct ata_host *host;
struct ata_port *ap;
void __iomem *cmd_addr, *ctl_addr;
+ int irq = 0;
+ irq_handler_t handler = NULL;
if (pnp_port_valid(idev, 0) == 0)
return -ENODEV;
- /* FIXME: Should selected polled PIO here not fail */
- if (pnp_irq_valid(idev, 0) == 0)
- return -ENODEV;
+ if (pnp_irq_valid(idev, 0)) {
+ irq = pnp_irq(idev, 0);
+ handler = ata_interrupt;
+ }
/* allocate host */
host = ata_host_alloc(&idev->dev, 1);
(unsigned long long)pnp_port_start(idev, 1));
/* activate */
- return ata_host_activate(host, pnp_irq(idev, 0), ata_interrupt, 0,
+ return ata_host_activate(host, irq, handler, 0,
&isapnp_sht);
}
* actually do our cable checking etc. Thankfully we don't need
* to do the plumbing for other cases.
*/
- switch (port_map[port])
- {
+ switch (port_map[port]) {
case PORT_PATA0:
- if (control & (1 << 5))
- return 0;
+ if ((control & (1 << 5)) == 0)
+ return -ENOENT;
if (control & (1 << 3)) /* 40/80 pin primary */
ap->cbl = ATA_CBL_PATA40;
else
case PORT_PATA1:
/* Bit 21 is set if the port is enabled */
if ((control5 & (1 << 21)) == 0)
- return 0;
+ return -ENOENT;
if (control5 & (1 << 19)) /* 40/80 pin secondary */
ap->cbl = ATA_CBL_PATA40;
else
#include <linux/libata.h>
#define DRV_NAME "pata_sil680"
-#define DRV_VERSION "0.4.7"
+#define DRV_VERSION "0.4.8"
#define SIL680_MMIO_BAR 5
return ATA_CBL_PATA40;
}
-/**
- * sil680_bus_reset - reset the SIL680 bus
- * @link: ATA link to reset
- * @deadline: deadline jiffies for the operation
- *
- * Perform the SIL680 housekeeping when doing an ATA bus reset
- */
-
-static int sil680_bus_reset(struct ata_link *link, unsigned int *classes,
- unsigned long deadline)
-{
- struct ata_port *ap = link->ap;
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- unsigned long addr = sil680_selreg(ap, 0);
- u8 reset;
-
- pci_read_config_byte(pdev, addr, &reset);
- pci_write_config_byte(pdev, addr, reset | 0x03);
- udelay(25);
- pci_write_config_byte(pdev, addr, reset);
- return ata_std_softreset(link, classes, deadline);
-}
-
-static void sil680_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, ata_std_prereset, sil680_bus_reset, NULL, ata_std_postreset);
-}
-
/**
* sil680_set_piomode - set initial PIO mode data
* @ap: ATA interface
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
- .error_handler = sil680_error_handler,
+ .error_handler = ata_bmdma_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = sil680_cable_detect,
/* devid, subvendor, subdev */
{ 0x5513, 0x1043, 0x1107 }, /* ASUS A6K */
{ 0x5513, 0x1734, 0x105F }, /* FSC Amilo A1630 */
+ { 0x5513, 0x1071, 0x8640 }, /* EasyNote K5305 */
/* end marker */
{ 0, }
};
SIL24_HOST_BAR = 0,
SIL24_PORT_BAR = 2,
+ /* sil24 fetches in chunks of 64bytes. The first block
+ * contains the PRB and two SGEs. From the second block, it's
+ * consisted of four SGEs and called SGT. Calculate the
+ * number of SGTs that fit into one page.
+ */
+ SIL24_PRB_SZ = sizeof(struct sil24_prb)
+ + 2 * sizeof(struct sil24_sge),
+ SIL24_MAX_SGT = (PAGE_SIZE - SIL24_PRB_SZ)
+ / (4 * sizeof(struct sil24_sge)),
+
+ /* This will give us one unused SGEs for ATA. This extra SGE
+ * will be used to store CDB for ATAPI devices.
+ */
+ SIL24_MAX_SGE = 4 * SIL24_MAX_SGT + 1,
+
/*
* Global controller registers (128 bytes @ BAR0)
*/
struct sil24_ata_block {
struct sil24_prb prb;
- struct sil24_sge sge[LIBATA_MAX_PRD];
+ struct sil24_sge sge[SIL24_MAX_SGE];
};
struct sil24_atapi_block {
struct sil24_prb prb;
u8 cdb[16];
- struct sil24_sge sge[LIBATA_MAX_PRD - 1];
+ struct sil24_sge sge[SIL24_MAX_SGE];
};
union sil24_cmd_block {
.change_queue_depth = ata_scsi_change_queue_depth,
.can_queue = SIL24_MAX_CMDS,
.this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
+ .sg_tablesize = SIL24_MAX_SGE,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
{
+ extern int __MARKER__sil24_cmd_block_is_sized_wrongly;
static int printed_version;
struct ata_port_info pi = sil24_port_info[ent->driver_data];
const struct ata_port_info *ppi[] = { &pi, NULL };
int i, rc;
u32 tmp;
+ /* cause link error if sil24_cmd_block is sized wrongly */
+ if (sizeof(union sil24_cmd_block) != PAGE_SIZE)
+ __MARKER__sil24_cmd_block_is_sized_wrongly = 1;
+
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
err = virtio_config_val(vdev, VIRTIO_CONFIG_BLK_F_CAPACITY, &cap);
if (err) {
dev_err(&vdev->dev, "Bad/missing capacity in config\n");
- goto out_put_disk;
+ goto out_cleanup_queue;
}
/* If capacity is too big, truncate with warning. */
blk_queue_max_segment_size(vblk->disk->queue, v);
else if (err != -ENOENT) {
dev_err(&vdev->dev, "Bad SIZE_MAX in config\n");
- goto out_put_disk;
+ goto out_cleanup_queue;
}
err = virtio_config_val(vdev, VIRTIO_CONFIG_BLK_F_SEG_MAX, &v);
blk_queue_max_hw_segments(vblk->disk->queue, v);
else if (err != -ENOENT) {
dev_err(&vdev->dev, "Bad SEG_MAX in config\n");
- goto out_put_disk;
+ goto out_cleanup_queue;
}
add_disk(vblk->disk);
return 0;
+out_cleanup_queue:
+ blk_cleanup_queue(vblk->disk->queue);
out_put_disk:
put_disk(vblk->disk);
out_unregister_blkdev:
put_disk(vblk->disk);
unregister_blkdev(major, "virtblk");
mempool_destroy(vblk->pool);
+ /* There should be nothing in the queue now, so no need to shutdown */
+ vdev->config->del_vq(vblk->vq);
kfree(vblk);
}
u_long flags;
isdn_net_dev *p;
isdn_net_phone *n;
- char nr[32];
+ char nr[ISDN_MSNLEN];
char *my_eaz;
/* Search name in netdev-chain */
nr[1] = '\0';
printk(KERN_INFO "isdn_net: Incoming call without OAD, assuming '0'\n");
} else
- strcpy(nr, setup->phone);
+ strlcpy(nr, setup->phone, ISDN_MSNLEN);
si1 = (int) setup->si1;
si2 = (int) setup->si2;
if (!setup->eazmsn[0]) {
chidx = -1;
}
}
- strcpy(lp->msn, cfg->eaz);
+ strlcpy(lp->msn, cfg->eaz, sizeof(lp->msn));
lp->pre_device = drvidx;
lp->pre_channel = chidx;
lp->onhtime = cfg->onhtime;
if (p) {
if (!(n = kmalloc(sizeof(isdn_net_phone), GFP_KERNEL)))
return -ENOMEM;
- strcpy(n->num, phone->phone);
+ strlcpy(n->num, phone->phone, sizeof(n->num));
n->next = p->local->phone[phone->outgoing & 1];
p->local->phone[phone->outgoing & 1] = n;
return 0;
{
struct lguest_vq_info *lvq = vq->priv;
+ /* Release the interrupt */
+ free_irq(lvq->config.irq, vq);
/* Tell virtio_ring.c to free the virtqueue. */
vring_del_virtqueue(vq);
/* Unmap the pages containing the ring. */
* 02110-1301, USA.
*/
-#define IBM_VERSION "0.16"
+#define IBM_VERSION "0.17"
#define TPACPI_SYSFS_VERSION 0x020000
/*
KEY_UNKNOWN, /* 0x0C: FN+BACKSPACE */
KEY_UNKNOWN, /* 0x0D: FN+INSERT */
KEY_UNKNOWN, /* 0x0E: FN+DELETE */
- KEY_BRIGHTNESSUP, /* 0x0F: FN+HOME (brightness up) */
+ KEY_RESERVED, /* 0x0F: FN+HOME (brightness up) */
/* Scan codes 0x10 to 0x1F: Extended ACPI HKEY hot keys */
- KEY_BRIGHTNESSDOWN, /* 0x10: FN+END (brightness down) */
+ KEY_RESERVED, /* 0x10: FN+END (brightness down) */
KEY_RESERVED, /* 0x11: FN+PGUP (thinklight toggle) */
KEY_UNKNOWN, /* 0x12: FN+PGDOWN */
KEY_ZOOM, /* 0x13: FN+SPACE (zoom) */
- KEY_VOLUMEUP, /* 0x14: VOLUME UP */
- KEY_VOLUMEDOWN, /* 0x15: VOLUME DOWN */
- KEY_MUTE, /* 0x16: MUTE */
+ KEY_RESERVED, /* 0x14: VOLUME UP */
+ KEY_RESERVED, /* 0x15: VOLUME DOWN */
+ KEY_RESERVED, /* 0x16: MUTE */
KEY_VENDOR, /* 0x17: Thinkpad/AccessIBM/Lenovo */
/* (assignments unknown, please report if found) */
KEY_UNKNOWN, KEY_UNKNOWN, KEY_UNKNOWN, KEY_UNKNOWN,
KEY_RESERVED, /* 0x11: FN+PGUP (thinklight toggle) */
KEY_UNKNOWN, /* 0x12: FN+PGDOWN */
KEY_ZOOM, /* 0x13: FN+SPACE (zoom) */
- KEY_VOLUMEUP, /* 0x14: VOLUME UP */
- KEY_VOLUMEDOWN, /* 0x15: VOLUME DOWN */
- KEY_MUTE, /* 0x16: MUTE */
+ KEY_RESERVED, /* 0x14: VOLUME UP */
+ KEY_RESERVED, /* 0x15: VOLUME DOWN */
+ KEY_RESERVED, /* 0x16: MUTE */
KEY_VENDOR, /* 0x17: Thinkpad/AccessIBM/Lenovo */
/* (assignments unknown, please report if found) */
KEY_UNKNOWN, KEY_UNKNOWN, KEY_UNKNOWN, KEY_UNKNOWN,
return len;
}
- res = mutex_lock_interruptible(&hotkey_mutex);
- if (res < 0)
- return res;
+ if (mutex_lock_interruptible(&hotkey_mutex))
+ return -ERESTARTSYS;
res = hotkey_get(&status, &mask);
mutex_unlock(&hotkey_mutex);
if (res)
if (!tp_features.hotkey)
return -ENODEV;
- res = mutex_lock_interruptible(&hotkey_mutex);
- if (res < 0)
- return res;
+ if (mutex_lock_interruptible(&hotkey_mutex))
+ return -ERESTARTSYS;
res = hotkey_get(&status, &mask);
if (res)
static struct mutex brightness_mutex;
+static int __init tpacpi_query_bcll_levels(acpi_handle handle)
+{
+ struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+ union acpi_object *obj;
+ int rc;
+
+ if (ACPI_SUCCESS(acpi_evaluate_object(handle, NULL, NULL, &buffer))) {
+ obj = (union acpi_object *)buffer.pointer;
+ if (!obj || (obj->type != ACPI_TYPE_PACKAGE)) {
+ printk(IBM_ERR "Unknown BCLL data, "
+ "please report this to %s\n", IBM_MAIL);
+ rc = 0;
+ } else {
+ rc = obj->package.count;
+ }
+ } else {
+ return 0;
+ }
+
+ kfree(buffer.pointer);
+ return rc;
+}
+
+static acpi_status __init brightness_find_bcll(acpi_handle handle, u32 lvl,
+ void *context, void **rv)
+{
+ char name[ACPI_PATH_SEGMENT_LENGTH];
+ struct acpi_buffer buffer = { sizeof(name), &name };
+
+ if (ACPI_SUCCESS(acpi_get_name(handle, ACPI_SINGLE_NAME, &buffer)) &&
+ !strncmp("BCLL", name, sizeof(name) - 1)) {
+ if (tpacpi_query_bcll_levels(handle) == 16) {
+ *rv = handle;
+ return AE_CTRL_TERMINATE;
+ } else {
+ return AE_OK;
+ }
+ } else {
+ return AE_OK;
+ }
+}
+
+static int __init brightness_check_levels(void)
+{
+ int status;
+ void *found_node = NULL;
+
+ if (!vid_handle) {
+ IBM_ACPIHANDLE_INIT(vid);
+ }
+ if (!vid_handle)
+ return 0;
+
+ /* Search for a BCLL package with 16 levels */
+ status = acpi_walk_namespace(ACPI_TYPE_PACKAGE, vid_handle, 3,
+ brightness_find_bcll, NULL, &found_node);
+
+ return (ACPI_SUCCESS(status) && found_node != NULL);
+}
+
+static acpi_status __init brightness_find_bcl(acpi_handle handle, u32 lvl,
+ void *context, void **rv)
+{
+ char name[ACPI_PATH_SEGMENT_LENGTH];
+ struct acpi_buffer buffer = { sizeof(name), &name };
+
+ if (ACPI_SUCCESS(acpi_get_name(handle, ACPI_SINGLE_NAME, &buffer)) &&
+ !strncmp("_BCL", name, sizeof(name) - 1)) {
+ *rv = handle;
+ return AE_CTRL_TERMINATE;
+ } else {
+ return AE_OK;
+ }
+}
+
+static int __init brightness_check_std_acpi_support(void)
+{
+ int status;
+ void *found_node = NULL;
+
+ if (!vid_handle) {
+ IBM_ACPIHANDLE_INIT(vid);
+ }
+ if (!vid_handle)
+ return 0;
+
+ /* Search for a _BCL method, but don't execute it */
+ status = acpi_walk_namespace(ACPI_TYPE_METHOD, vid_handle, 3,
+ brightness_find_bcl, NULL, &found_node);
+
+ return (ACPI_SUCCESS(status) && found_node != NULL);
+}
+
static int __init brightness_init(struct ibm_init_struct *iibm)
{
int b;
mutex_init(&brightness_mutex);
+ if (!brightness_enable) {
+ dbg_printk(TPACPI_DBG_INIT,
+ "brightness support disabled by module parameter\n");
+ return 1;
+ } else if (brightness_enable > 1) {
+ if (brightness_check_std_acpi_support()) {
+ printk(IBM_NOTICE
+ "standard ACPI backlight interface available, not loading native one...\n");
+ return 1;
+ }
+ }
+
if (!brightness_mode) {
if (thinkpad_id.vendor == PCI_VENDOR_ID_LENOVO)
brightness_mode = 2;
if (brightness_mode > 3)
return -EINVAL;
+ tp_features.bright_16levels =
+ thinkpad_id.vendor == PCI_VENDOR_ID_LENOVO &&
+ brightness_check_levels();
+
b = brightness_get(NULL);
if (b < 0)
return 1;
+ if (tp_features.bright_16levels)
+ printk(IBM_INFO "detected a 16-level brightness capable ThinkPad\n");
+
ibm_backlight_device = backlight_device_register(
TPACPI_BACKLIGHT_DEV_NAME, NULL, NULL,
&ibm_backlight_data);
}
vdbg_printk(TPACPI_DBG_INIT, "brightness is supported\n");
- ibm_backlight_device->props.max_brightness = 7;
+ ibm_backlight_device->props.max_brightness =
+ (tp_features.bright_16levels)? 15 : 7;
ibm_backlight_device->props.brightness = b;
backlight_update_status(ibm_backlight_device);
static int brightness_update_status(struct backlight_device *bd)
{
+ /* it is the backlight class's job (caller) to handle
+ * EINTR and other errors properly */
return brightness_set(
(bd->props.fb_blank == FB_BLANK_UNBLANK &&
bd->props.power == FB_BLANK_UNBLANK) ?
if (brightness_mode & 1) {
if (!acpi_ec_read(brightness_offset, &lec))
return -EIO;
- lec &= 7;
+ lec &= (tp_features.bright_16levels)? 0x0f : 0x07;
level = lec;
};
if (brightness_mode & 2) {
lcmos = (nvram_read_byte(TP_NVRAM_ADDR_BRIGHTNESS)
& TP_NVRAM_MASK_LEVEL_BRIGHTNESS)
>> TP_NVRAM_POS_LEVEL_BRIGHTNESS;
+ lcmos &= (tp_features.bright_16levels)? 0x0f : 0x07;
level = lcmos;
}
return level;
}
+/* May return EINTR which can always be mapped to ERESTARTSYS */
static int brightness_set(int value)
{
int cmos_cmd, inc, i, res;
int current_value;
- if (value > 7)
+ if (value > ((tp_features.bright_16levels)? 15 : 7))
return -EINVAL;
res = mutex_lock_interruptible(&brightness_mutex);
cmos_cmd = value > current_value ?
TP_CMOS_BRIGHTNESS_UP :
TP_CMOS_BRIGHTNESS_DOWN;
- inc = value > current_value ? 1 : -1;
+ inc = (value > current_value)? 1 : -1;
res = 0;
for (i = current_value; i != value; i += inc) {
if ((level = brightness_get(NULL)) < 0) {
len += sprintf(p + len, "level:\t\tunreadable\n");
} else {
- len += sprintf(p + len, "level:\t\t%d\n", level & 0x7);
+ len += sprintf(p + len, "level:\t\t%d\n", level);
len += sprintf(p + len, "commands:\tup, down\n");
len += sprintf(p + len, "commands:\tlevel <level>"
- " (<level> is 0-7)\n");
+ " (<level> is 0-%d)\n",
+ (tp_features.bright_16levels) ? 15 : 7);
}
return len;
static int brightness_write(char *buf)
{
int level;
- int new_level;
+ int rc;
char *cmd;
+ int max_level = (tp_features.bright_16levels) ? 15 : 7;
- while ((cmd = next_cmd(&buf))) {
- if ((level = brightness_get(NULL)) < 0)
- return level;
- level &= 7;
+ level = brightness_get(NULL);
+ if (level < 0)
+ return level;
+ while ((cmd = next_cmd(&buf))) {
if (strlencmp(cmd, "up") == 0) {
- new_level = level == 7 ? 7 : level + 1;
+ if (level < max_level)
+ level++;
} else if (strlencmp(cmd, "down") == 0) {
- new_level = level == 0 ? 0 : level - 1;
- } else if (sscanf(cmd, "level %d", &new_level) == 1 &&
- new_level >= 0 && new_level <= 7) {
- /* new_level set */
+ if (level > 0)
+ level--;
+ } else if (sscanf(cmd, "level %d", &level) == 1 &&
+ level >= 0 && level <= max_level) {
+ /* new level set */
} else
return -EINVAL;
-
- brightness_set(new_level);
}
- return 0;
+ /*
+ * Now we know what the final level should be, so we try to set it.
+ * Doing it this way makes the syscall restartable in case of EINTR
+ */
+ rc = brightness_set(level);
+ return (rc == -EINTR)? ERESTARTSYS : rc;
}
static struct ibm_struct brightness_driver_data = {
/* scale down from 0-255 to 0-7 */
newlevel = (s >> 5) & 0x07;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
rc = fan_get_status(&status);
if (!rc && (status &
int rc;
u8 s;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
rc = fan_get_status(&s);
if (!rc)
fan_update_desired_level(s);
if (!fan_control_allowed)
return -EPERM;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
if (level == TPACPI_FAN_LAST_LEVEL)
level = fan_control_desired_level;
if (!fan_control_allowed)
return -EPERM;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
switch (fan_control_access_mode) {
case TPACPI_FAN_WR_ACPI_FANS:
if (!fan_control_allowed)
return -EPERM;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
rc = 0;
switch (fan_control_access_mode) {
if (!fan_control_allowed)
return -EPERM;
- rc = mutex_lock_interruptible(&fan_mutex);
- if (rc < 0)
- return rc;
+ if (mutex_lock_interruptible(&fan_mutex))
+ return -ERESTARTSYS;
rc = 0;
switch (fan_control_access_mode) {
unsigned int i;
struct ibm_struct *ibm;
+ if (!kp || !kp->name || !val)
+ return -EINVAL;
+
for (i = 0; i < ARRAY_SIZE(ibms_init); i++) {
ibm = ibms_init[i].data;
- BUG_ON(ibm == NULL);
+ WARN_ON(ibm == NULL);
+
+ if (!ibm || !ibm->name)
+ continue;
if (strcmp(ibm->name, kp->name) == 0 && ibm->write) {
if (strlen(val) > sizeof(ibms_init[i].param) - 2)
static int brightness_mode;
module_param_named(brightness_mode, brightness_mode, int, 0);
+static unsigned int brightness_enable = 2; /* 2 = auto, 0 = no, 1 = yes */
+module_param(brightness_enable, uint, 0);
+
static unsigned int hotkey_report_mode;
module_param(hotkey_report_mode, uint, 0);
/* ThinkPad CMOS NVRAM constants */
#define TP_NVRAM_ADDR_BRIGHTNESS 0x5e
-#define TP_NVRAM_MASK_LEVEL_BRIGHTNESS 0x07
+#define TP_NVRAM_MASK_LEVEL_BRIGHTNESS 0x0f
#define TP_NVRAM_POS_LEVEL_BRIGHTNESS 0
#define onoff(status,bit) ((status) & (1 << (bit)) ? "on" : "off")
u32 hotkey_wlsw:1;
u32 light:1;
u32 light_status:1;
+ u32 bright_16levels:1;
u32 wan:1;
u32 fan_ctrl_status_undef:1;
u32 input_device_registered:1;
static struct backlight_device *ibm_backlight_device;
static int brightness_offset = 0x31;
static int brightness_mode;
+static unsigned int brightness_enable; /* 0 = no, 1 = yes, 2 = auto */
static int brightness_init(struct ibm_init_struct *iibm);
static void brightness_exit(void);
* max 8 partitions per card
*/
#define MMC_SHIFT 3
+#define MMC_NUM_MINORS (256 >> MMC_SHIFT)
+
+static unsigned long dev_use[MMC_NUM_MINORS/(8*sizeof(unsigned long))];
/*
* There is one mmc_blk_data per slot.
mutex_lock(&open_lock);
md->usage--;
if (md->usage == 0) {
+ int devidx = md->disk->first_minor >> MMC_SHIFT;
+ __clear_bit(devidx, dev_use);
+
put_disk(md->disk);
kfree(md);
}
req->rq_disk->disk_name, err);
goto cmd_err;
}
- } while (!(cmd.resp[0] & R1_READY_FOR_DATA));
+ /*
+ * Some cards mishandle the status bits,
+ * so make sure to check both the busy
+ * indication and the card state.
+ */
+ } while (!(cmd.resp[0] & R1_READY_FOR_DATA) ||
+ (R1_CURRENT_STATE(cmd.resp[0]) == 7));
#if 0
if (cmd.resp[0] & ~0x00000900)
return 0;
}
-#define MMC_NUM_MINORS (256 >> MMC_SHIFT)
-
-static unsigned long dev_use[MMC_NUM_MINORS/(8*sizeof(unsigned long))];
static inline int mmc_blk_readonly(struct mmc_card *card)
{
struct mmc_blk_data *md = mmc_get_drvdata(card);
if (md) {
- int devidx;
-
/* Stop new requests from getting into the queue */
del_gendisk(md->disk);
/* Then flush out any already in there */
mmc_cleanup_queue(&md->queue);
- devidx = md->disk->first_minor >> MMC_SHIFT;
- __clear_bit(devidx, dev_use);
-
mmc_blk_put(md);
}
mmc_set_drvdata(card, NULL);
#include <linux/mmc/host.h>
#include <linux/highmem.h>
#include <linux/scatterlist.h>
-#include <linux/log2.h>
#include <asm/io.h>
#define DRIVER_NAME "tifm_sd"
goto err_out;
}
- if (mrq->data && !is_power_of_2(mrq->data->blksz)) {
- printk(KERN_ERR "%s: Unsupported block size (%d bytes)\n",
- sock->dev.bus_id, mrq->data->blksz);
- mrq->cmd->error = -EINVAL;
- goto err_out;
- }
-
host->cmd_flags = 0;
host->block_pos = 0;
host->sg_pos = 0;
+ if (mrq->data && !is_power_of_2(mrq->data->blksz))
+ host->no_dma = 1;
+ else
+ host->no_dma = no_dma ? 1 : 0;
+
if (r_data) {
tifm_sd_set_data_timeout(host, r_data);
: PCI_DMA_FROMDEVICE)) {
printk(KERN_ERR "%s : scatterlist map failed\n",
sock->dev.bus_id);
- spin_unlock_irqrestore(&sock->lock, flags);
+ mrq->cmd->error = -ENOMEM;
goto err_out;
}
host->sg_len = tifm_map_sg(sock, r_data->sg,
r_data->flags & MMC_DATA_WRITE
? PCI_DMA_TODEVICE
: PCI_DMA_FROMDEVICE);
- spin_unlock_irqrestore(&sock->lock, flags);
+ mrq->cmd->error = -ENOMEM;
goto err_out;
}
return -ENOMEM;
host = mmc_priv(mmc);
- host->no_dma = no_dma;
tifm_set_drvdata(sock, mmc);
host->dev = sock;
host->timeout_jiffies = msecs_to_jiffies(1000);
case PLIP_PK_DONE:
/* Inform the upper layer for the arrival of a packet. */
rcv->skb->protocol=plip_type_trans(rcv->skb, dev);
- netif_rx(rcv->skb);
+ netif_rx_ni(rcv->skb);
dev->last_rx = jiffies;
dev->stats.rx_bytes += rcv->length.h;
dev->stats.rx_packets++;
nl = netdev_priv(dev);
nl->dev = dev;
- nl->pardev = parport_register_device(port, name, plip_preempt,
+ nl->pardev = parport_register_device(port, dev->name, plip_preempt,
plip_wakeup, plip_interrupt,
0, dev);
if (vi->num < vi->max / 2)
try_fill_recv(vi);
- /* All done? */
- if (!skb) {
+ /* Out of packets? */
+ if (received < budget) {
netif_rx_complete(vi->dev, napi);
if (unlikely(!vi->rvq->vq_ops->restart(vi->rvq))
&& netif_rx_reschedule(vi->dev, napi))
static void virtnet_remove(struct virtio_device *vdev)
{
- unregister_netdev(vdev->priv);
- free_netdev(vdev->priv);
+ struct virtnet_info *vi = vdev->priv;
+
+ vdev->config->del_vq(vi->svq);
+ vdev->config->del_vq(vi->rvq);
+ unregister_netdev(vi->dev);
+ free_netdev(vi->dev);
}
static struct virtio_device_id id_table[] = {
{
int i = 0;
int irq;
+ int p, t;
if (!valid_IRQ(gsi))
return;
if (i >= PNP_MAX_IRQ)
return;
-#ifdef CONFIG_X86
- if (gsi < 16 && (triggering != ACPI_EDGE_SENSITIVE ||
- polarity != ACPI_ACTIVE_HIGH)) {
- pnp_warn("BIOS BUG: legacy PNP IRQ %d should be edge trigger, "
- "active high", gsi);
- triggering = ACPI_EDGE_SENSITIVE;
- polarity = ACPI_ACTIVE_HIGH;
+ /*
+ * in IO-APIC mode, use overrided attribute. Two reasons:
+ * 1. BIOS bug in DSDT
+ * 2. BIOS uses IO-APIC mode Interrupt Source Override
+ */
+ if (!acpi_get_override_irq(gsi, &t, &p)) {
+ t = t ? ACPI_LEVEL_SENSITIVE : ACPI_EDGE_SENSITIVE;
+ p = p ? ACPI_ACTIVE_LOW : ACPI_ACTIVE_HIGH;
+
+ if (triggering != t || polarity != p) {
+ pnp_warn("IRQ %d override to %s, %s",
+ gsi, t ? "edge":"level", p ? "low":"high");
+ triggering = t;
+ polarity = p;
+ }
}
-#endif
res->irq_resource[i].flags = IORESOURCE_IRQ; // Also clears _UNSET flag
res->irq_resource[i].flags |= irq_flags(triggering, polarity);
void css_schedule_reprobe(void)
{
need_reprobe = 1;
- queue_work(ccw_device_work, &css_reprobe_work);
+ queue_work(slow_path_wq, &css_reprobe_work);
}
EXPORT_SYMBOL_GPL(css_schedule_reprobe);
if (sch->schib.pmcw.dev != cdev->private->dev_id.devno) {
PREPARE_WORK(&cdev->private->kick_work,
ccw_device_move_to_orphanage);
- queue_work(ccw_device_work, &cdev->private->kick_work);
+ queue_work(slow_path_wq, &cdev->private->kick_work);
} else
ccw_device_start_id(cdev, 0);
}
{
struct subchannel *sch;
struct ccw1 *ccw;
- int ret;
sch = to_subchannel(cdev->dev.parent);
/* Setup sense channel program. */
ccw = cdev->private->iccws;
- if (sch->schib.pmcw.pim != 0x80) {
- /* more than one path installed. */
- ccw->cmd_code = CCW_CMD_SUSPEND_RECONN;
- ccw->cda = 0;
- ccw->count = 0;
- ccw->flags = CCW_FLAG_SLI | CCW_FLAG_CC;
- ccw++;
- }
ccw->cmd_code = CCW_CMD_SENSE_ID;
ccw->cda = (__u32) __pa (&cdev->private->senseid);
ccw->count = sizeof (struct senseid);
/* Reset device status. */
memset(&cdev->private->irb, 0, sizeof(struct irb));
+ cdev->private->flags.intretry = 0;
- /* Try on every path. */
- ret = -ENODEV;
- while (cdev->private->imask != 0) {
- if ((sch->opm & cdev->private->imask) != 0 &&
- cdev->private->iretry > 0) {
- cdev->private->iretry--;
- /* Reset internal retry indication. */
- cdev->private->flags.intretry = 0;
- ret = cio_start (sch, cdev->private->iccws,
- cdev->private->imask);
- /* ret is 0, -EBUSY, -EACCES or -ENODEV */
- if (ret != -EACCES)
- return ret;
- }
- cdev->private->imask >>= 1;
- cdev->private->iretry = 5;
- }
- return ret;
+ return cio_start(sch, ccw, LPM_ANYPATH);
}
void
memset (&cdev->private->senseid, 0, sizeof (struct senseid));
cdev->private->senseid.cu_type = 0xFFFF;
- cdev->private->imask = 0x80;
- cdev->private->iretry = 5;
+ cdev->private->iretry = 3;
ret = __ccw_device_sense_id_start(cdev);
if (ret && ret != -EBUSY)
ccw_device_sense_id_done(cdev, ret);
ccw_device_sense_id_done(cdev, ret);
break;
case -EACCES: /* channel is not operational. */
- sch->lpm &= ~cdev->private->imask;
- cdev->private->imask >>= 1;
- cdev->private->iretry = 5;
- /* fall through. */
case -EAGAIN: /* try again. */
- ret = __ccw_device_sense_id_start(cdev);
- if (ret == 0 || ret == -EBUSY)
- break;
+ cdev->private->iretry--;
+ if (cdev->private->iretry > 0) {
+ ret = __ccw_device_sense_id_start(cdev);
+ if (ret == 0 || ret == -EBUSY)
+ break;
+ }
/* fall through. */
default: /* Sense ID failed. Try asking VM. */
if (MACHINE_IS_VM) {
CHIP_DEF(PCI_CHIP_RV380_3154, RV380, CHIP_HAS_CRTC2 | CHIP_IS_MOBILITY),
CHIP_DEF(PCI_CHIP_RV370_5B60, RV380, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_RV370_5B62, RV380, CHIP_HAS_CRTC2),
+ CHIP_DEF(PCI_CHIP_RV370_5B63, RV380, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_RV370_5B64, RV380, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_RV370_5B65, RV380, CHIP_HAS_CRTC2),
CHIP_DEF(PCI_CHIP_RV370_5460, RV380, CHIP_HAS_CRTC2 | CHIP_IS_MOBILITY),
return err;
}
+static int virtio_dev_remove(struct device *_d)
+{
+ struct virtio_device *dev = container_of(_d,struct virtio_device,dev);
+ struct virtio_driver *drv = container_of(dev->dev.driver,
+ struct virtio_driver, driver);
+
+ dev->config->set_status(dev, dev->config->get_status(dev)
+ & ~VIRTIO_CONFIG_S_DRIVER);
+ drv->remove(dev);
+ return 0;
+}
+
int register_virtio_driver(struct virtio_driver *driver)
{
driver->driver.bus = &virtio_bus;
driver->driver.probe = virtio_dev_probe;
+ driver->driver.remove = virtio_dev_remove;
return driver_register(&driver->driver);
}
EXPORT_SYMBOL_GPL(register_virtio_driver);
}
+static int zorro_device_remove(struct device *dev)
+{
+ struct zorro_dev *z = to_zorro_dev(dev);
+ struct zorro_driver *drv = to_zorro_driver(dev->driver);
+
+ if (drv) {
+ if (drv->remove)
+ drv->remove(z);
+ z->driver = NULL;
+ }
+ return 0;
+}
+
+
/**
* zorro_register_driver - register a new Zorro driver
* @drv: the driver structure to register
.name = "zorro",
.match = zorro_bus_match,
.probe = zorro_device_probe,
+ .remove = zorro_device_remove,
};
Version 1.52
------------
Fix oops on second mount to server when null auth is used.
+Enable experimental Kerberos support. Return writebehind errors on flush
+and sync so that events like out of disk space get reported properly on
+cached files.
Version 1.51
------------
Restrictions
============
-Servers must support the NTLM SMB dialect (which is the most recent, supported
-by Samba and Windows NT version 4, 2000 and XP and many other SMB/CIFS servers)
Servers must support either "pure-TCP" (port 445 TCP/IP CIFS connections) or RFC
-1001/1002 support for "Netbios-Over-TCP/IP." Neither of these is likely to be a
-problem as most servers support this. IPv6 support is planned for the future,
-and is almost complete.
+1001/1002 support for "Netbios-Over-TCP/IP." This is not likely to be a
+problem as most servers support this.
Valid filenames differ between Windows and Linux. Windows typically restricts
filenames which contain certain reserved characters (e.g.the character :
byte range locks).
remount remount the share (often used to change from ro to rw mounts
or vice versa)
+ cifsacl Report mode bits (e.g. on stat) based on the Windows ACL for
+ the file. (EXPERIMENTAL)
servern Specify the server 's netbios name (RFC1001 name) to use
when attempting to setup a session to the server. This is
This is needed for mounting to some older servers (such
performance enhancement was disabled when
signing turned on in case buffer was modified
just before it was sent, also this flag will
- be used to use the new experimental sessionsetup
- code).
+ be used to use the new experimental directory change
+ notification code).
These experimental features and tracing can be enabled by changing flags in
/proc/fs/cifs (after the cifs module has been installed or built into the
Two other experimental features are under development. To test these
requires enabling CONFIG_CIFS_EXPERIMENTAL
- ipv6 enablement
+ cifsacl support needed to retrieve approximated mode bits based on
+ the contents on the CIFS ACL.
DNOTIFY fcntl: needed for support of directory change
notification and perhaps later for file leases)
returned success.
Also note that "cat /proc/fs/cifs/DebugData" will display information about
-the active sessions and the shares that are mounted. Note: NTLMv2 enablement
-will not work since its implementation is not quite complete yet. Do not alter
-the ExtendedSecurity configuration value unless you are doing specific testing.
-Enabling extended security works to Windows 2000 Workstations and XP but not to
-Windows 2000 server or Samba since it does not usually send "raw NTLMSSP"
-(instead it sends NTLMSSP encapsulated in SPNEGO/GSSAPI, which support is not
-complete in the CIFS VFS yet).
+the active sessions and the shares that are mounted.
+Enabling Kerberos (extended security) works when CONFIG_CIFS_EXPERIMENTAL is enabled
+but requires a user space helper (from the Samba project). NTLM and NTLMv2 and
+LANMAN support do not require this helpr.
c) Better pam/winbind integration (e.g. to handle uid mapping
better)
-d) Kerberos/SPNEGO session setup support - (started)
+d) Verify that Kerberos signing works
e) Cleanup now unneeded SessSetup code in
fs/cifs/connect.c and add back in NTLMSSP code if any servers
.describe = user_describe,
};
+#define MAX_VER_STR_LEN 9 /* length of longest version string e.g.
+ strlen(";ver=0xFF") */
+#define MAX_MECH_STR_LEN 13 /* length of longest security mechanism name, eg
+ in future could have strlen(";sec=ntlmsspi") */
+#define MAX_IPV6_ADDR_LEN 42 /* eg FEDC:BA98:7654:3210:FEDC:BA98:7654:3210/60 */
/* get a key struct with a SPNEGO security blob, suitable for session setup */
struct key *
-cifs_get_spnego_key(struct cifsSesInfo *sesInfo, const char *hostname)
+cifs_get_spnego_key(struct cifsSesInfo *sesInfo)
{
struct TCP_Server_Info *server = sesInfo->server;
char *description, *dp;
size_t desc_len;
struct key *spnego_key;
+ const char *hostname = server->hostname;
-
- /* version + ;ip{4|6}= + address + ;host=hostname +
- ;sec= + ;uid= + NULL */
- desc_len = 4 + 5 + 32 + 1 + 5 + strlen(hostname) +
- strlen(";sec=krb5") + 7 + sizeof(uid_t)*2 + 1;
+ /* BB: come up with better scheme for determining length */
+ /* length of fields (with semicolons): ver=0xyz ipv4= ipaddress host=
+ hostname sec=mechanism uid=0x uid */
+ desc_len = MAX_VER_STR_LEN + 5 + MAX_IPV6_ADDR_LEN + 1 + 6 +
+ strlen(hostname) + MAX_MECH_STR_LEN + 8 + (sizeof(uid_t) * 2);
spnego_key = ERR_PTR(-ENOMEM);
description = kzalloc(desc_len, GFP_KERNEL);
if (description == NULL)
dp = description;
/* start with version and hostname portion of UNC string */
spnego_key = ERR_PTR(-EINVAL);
- sprintf(dp, "0x%2.2x;host=%s;", CIFS_SPNEGO_UPCALL_VERSION,
+ sprintf(dp, "ver=0x%x;host=%s;", CIFS_SPNEGO_UPCALL_VERSION,
hostname);
dp = description + strlen(description);
#ifdef __KERNEL__
extern struct key_type cifs_spnego_key_type;
+extern struct key *cifs_get_spnego_key(struct cifsSesInfo *sesInfo);
#endif /* KERNEL */
#endif /* _CIFS_SPNEGO_H */
/* BB need to add parm so we can store the SID BB */
+ if (!pdacl) {
+ /* no DACL in the security descriptor, set
+ all the permissions for user/group/other */
+ inode->i_mode |= S_IRWXUGO;
+ return;
+ }
+
/* validate that we do not go past end of acl */
if (end_of_acl < (char *)pdacl + le16_to_cpu(pdacl->size)) {
cERROR(1, ("ACL too small to parse DACL"));
user/group/other have no permissions */
inode->i_mode &= ~(S_IRWXUGO);
- if (!pdacl) {
- /* no DACL in the security descriptor, set
- all the permissions for user/group/other */
- inode->i_mode |= S_IRWXUGO;
- return;
- }
acl_base = (char *)pdacl;
acl_size = sizeof(struct cifs_acl);
cifs_inode->cifsAttrs = 0x20; /* default */
atomic_set(&cifs_inode->inUse, 0);
cifs_inode->time = 0;
+ cifs_inode->write_behind_rc = 0;
/* Until the file is open and we have gotten oplock
info back from the server, can not assume caching of
file data or metadata */
struct cifsTconInfo *pTcon;
struct inode *inode;
__u16 netfid;
- int rc;
+ int rc, waitrc = 0;
set_freezable();
do {
filemap_fdatawrite(inode->i_mapping);
if (CIFS_I(inode)->clientCanCacheRead
== 0) {
- filemap_fdatawait(inode->i_mapping);
+ waitrc = filemap_fdatawait(inode->i_mapping);
invalidate_remote_inode(inode);
}
+ if (rc == 0)
+ rc = waitrc;
} else
rc = 0;
/* mutex_unlock(&inode->i_mutex);*/
unsigned int len;
union {
char ntlm[CIFS_SESS_KEY_SIZE + 16];
+ char krb5[CIFS_SESS_KEY_SIZE + 16]; /* BB: length correct? */
struct {
char key[16];
struct ntlmv2_resp resp;
/* 15 character server name + 0x20 16th byte indicating type = srv */
char server_RFC1001_name[SERVER_NAME_LEN_WITH_NULL];
char unicode_server_Name[SERVER_NAME_LEN_WITH_NULL * 2];
+ char *hostname; /* hostname portion of UNC string */
struct socket *ssocket;
union {
struct sockaddr_in sockAddr;
#define CIFS_LARGE_BUFFER 2
#define CIFS_IOVEC 4 /* array of response buffers */
+/* Type of Request to SendReceive2 */
+#define CIFS_STD_OP 0 /* normal request timeout */
+#define CIFS_LONG_OP 1 /* long op (up to 45 sec, oplock time) */
+#define CIFS_VLONG_OP 2 /* sloow op - can take up to 180 seconds */
+#define CIFS_BLOCKING_OP 4 /* operation can block */
+#define CIFS_ASYNC_OP 8 /* do not wait for response */
+#define CIFS_TIMEOUT_MASK 0x00F /* only one of 5 above set in req */
+#define CIFS_LOG_ERROR 0x010 /* log NT STATUS if non-zero */
+#define CIFS_LARGE_BUF_OP 0x020 /* large request buffer */
+#define CIFS_NO_RESP 0x040 /* no response buffer required */
+
/* Security Flags: indicate type of session setup needed */
#define CIFSSEC_MAY_SIGN 0x00001
#define CIFSSEC_MAY_NTLM 0x00002
struct smb_hdr * /* input */ ,
struct smb_hdr * /* out */ ,
int * /* bytes returned */ , const int long_op);
+extern int SendReceiveNoRsp(const unsigned int xid, struct cifsSesInfo *ses,
+ struct smb_hdr *in_buf, int flags);
extern int SendReceive2(const unsigned int /* xid */ , struct cifsSesInfo *,
struct kvec *, int /* nvec to send */,
- int * /* type of buf returned */ , const int long_op,
- const int logError /* whether to log status code*/ );
+ int * /* type of buf returned */ , const int flags);
extern int SendReceiveBlockingLock(const unsigned int /* xid */ ,
struct cifsTconInfo *,
struct smb_hdr * /* input */ ,
extern int small_smb_init_no_tc(const int smb_cmd, const int wct,
struct cifsSesInfo *ses,
void **request_buf);
-extern struct key *cifs_get_spnego_key(struct cifsSesInfo *sesInfo,
- const char *hostname);
extern int CIFS_SessSetup(unsigned int xid, struct cifsSesInfo *ses,
const int stage,
const struct nls_table *nls_cp);
extern int CIFSSMBOpen(const int xid, struct cifsTconInfo *tcon,
const char *fileName, const int disposition,
const int access_flags, const int omode,
- __u16 * netfid, int *pOplock, FILE_ALL_INFO *,
+ __u16 *netfid, int *pOplock, FILE_ALL_INFO *,
const struct nls_table *nls_codepage, int remap);
extern int SMBLegacyOpen(const int xid, struct cifsTconInfo *tcon,
const char *fileName, const int disposition,
const int access_flags, const int omode,
- __u16 * netfid, int *pOplock, FILE_ALL_INFO *,
+ __u16 *netfid, int *pOplock, FILE_ALL_INFO *,
const struct nls_table *nls_codepage, int remap);
extern int CIFSPOSIXCreate(const int xid, struct cifsTconInfo *tcon,
- u32 posix_flags, __u64 mode, __u16 * netfid,
+ u32 posix_flags, __u64 mode, __u16 *netfid,
FILE_UNIX_BASIC_INFO *pRetData,
__u32 *pOplock, const char *name,
const struct nls_table *nls_codepage, int remap);
const __u64 offset, unsigned int *nbytes,
struct kvec *iov, const int nvec, const int long_op);
extern int CIFSGetSrvInodeNumber(const int xid, struct cifsTconInfo *tcon,
- const unsigned char *searchName, __u64 * inode_number,
+ const unsigned char *searchName, __u64 *inode_number,
const struct nls_table *nls_codepage,
int remap_special_chars);
extern int cifs_convertUCSpath(char *target, const __le16 *source, int maxlen,
const char *local_acl, const int buflen, const int acl_type,
const struct nls_table *nls_codepage, int remap_special_chars);
extern int CIFSGetExtAttr(const int xid, struct cifsTconInfo *tcon,
- const int netfid, __u64 * pExtAttrBits, __u64 *pMask);
+ const int netfid, __u64 *pExtAttrBits, __u64 *pMask);
#endif /* _CIFSPROTO_H */
CIFSSMBTDis(const int xid, struct cifsTconInfo *tcon)
{
struct smb_hdr *smb_buffer;
- struct smb_hdr *smb_buffer_response; /* BB removeme BB */
int rc = 0;
- int length;
cFYI(1, ("In tree disconnect"));
/*
if (rc) {
up(&tcon->tconSem);
return rc;
- } else {
- smb_buffer_response = smb_buffer; /* BB removeme BB */
}
- rc = SendReceive(xid, tcon->ses, smb_buffer, smb_buffer_response,
- &length, 0);
+
+ rc = SendReceiveNoRsp(xid, tcon->ses, smb_buffer, 0);
if (rc)
cFYI(1, ("Tree disconnect failed %d", rc));
- if (smb_buffer)
- cifs_small_buf_release(smb_buffer);
up(&tcon->tconSem);
/* No need to return error on this operation if tid invalidated and
int
CIFSSMBLogoff(const int xid, struct cifsSesInfo *ses)
{
- struct smb_hdr *smb_buffer_response;
LOGOFF_ANDX_REQ *pSMB;
int rc = 0;
- int length;
cFYI(1, ("In SMBLogoff for session disconnect"));
if (ses)
return rc;
}
- smb_buffer_response = (struct smb_hdr *)pSMB; /* BB removeme BB */
-
if (ses->server) {
pSMB->hdr.Mid = GetNextMid(ses->server);
pSMB->hdr.Uid = ses->Suid;
pSMB->AndXCommand = 0xFF;
- rc = SendReceive(xid, ses, (struct smb_hdr *) pSMB,
- smb_buffer_response, &length, 0);
+ rc = SendReceiveNoRsp(xid, ses, (struct smb_hdr *) pSMB, 0);
if (ses->server) {
atomic_dec(&ses->server->socketUseCount);
if (atomic_read(&ses->server->socketUseCount) == 0) {
}
}
up(&ses->sesSem);
- cifs_small_buf_release(pSMB);
/* if session dead then we do not need to do ulogoff,
since server closed smb session, no sense reporting
pSMB->ByteCount = cpu_to_le16(count);
/* long_op set to 1 to allow for oplock break timeouts */
rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 1);
+ (struct smb_hdr *)pSMBr, &bytes_returned, CIFS_LONG_OP);
cifs_stats_inc(&tcon->num_opens);
if (rc) {
cFYI(1, ("Error in Open = %d", rc));
pSMB->ByteCount = cpu_to_le16(count);
/* long_op set to 1 to allow for oplock break timeouts */
rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 1);
+ (struct smb_hdr *)pSMBr, &bytes_returned, CIFS_LONG_OP);
cifs_stats_inc(&tcon->num_opens);
if (rc) {
cFYI(1, ("Error in Open = %d", rc));
iov[0].iov_base = (char *)pSMB;
iov[0].iov_len = pSMB->hdr.smb_buf_length + 4;
rc = SendReceive2(xid, tcon->ses, iov, 1 /* num iovecs */,
- &resp_buf_type, 0 /* not long op */, 1 /* log err */ );
+ &resp_buf_type, CIFS_STD_OP | CIFS_LOG_ERROR);
cifs_stats_inc(&tcon->num_reads);
pSMBr = (READ_RSP *)iov[0].iov_base;
if (rc) {
rc = SendReceive2(xid, tcon->ses, iov, n_vec + 1, &resp_buf_type,
- long_op, 0 /* do not log STATUS code */ );
+ long_op);
cifs_stats_inc(&tcon->num_writes);
if (rc) {
cFYI(1, ("Send error Write2 = %d", rc));
int timeout = 0;
__u16 count;
- cFYI(1, ("In CIFSSMBLock - timeout %d numLock %d", waitFlag, numLock));
+ cFYI(1, ("CIFSSMBLock timeout %d numLock %d", waitFlag, numLock));
rc = small_smb_init(SMB_COM_LOCKING_ANDX, 8, tcon, (void **) &pSMB);
if (rc)
pSMBr = (LOCK_RSP *)pSMB; /* BB removeme BB */
if (lockType == LOCKING_ANDX_OPLOCK_RELEASE) {
- timeout = -1; /* no response expected */
+ timeout = CIFS_ASYNC_OP; /* no response expected */
pSMB->Timeout = 0;
} else if (waitFlag == TRUE) {
- timeout = 3; /* blocking operation, no timeout */
+ timeout = CIFS_BLOCKING_OP; /* blocking operation, no timeout */
pSMB->Timeout = cpu_to_le32(-1);/* blocking - do not time out */
} else {
pSMB->Timeout = 0;
if (waitFlag) {
rc = SendReceiveBlockingLock(xid, tcon, (struct smb_hdr *) pSMB,
(struct smb_hdr *) pSMBr, &bytes_returned);
+ cifs_small_buf_release(pSMB);
} else {
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, timeout);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *)pSMB,
+ timeout);
+ /* SMB buffer freed by function above */
}
cifs_stats_inc(&tcon->num_locks);
if (rc) {
cFYI(1, ("Send error in Lock = %d", rc));
}
- cifs_small_buf_release(pSMB);
/* Note: On -EAGAIN error only caller can retry on handle based calls
since file handle passed in no longer valid */
int rc = 0;
int timeout = 0;
int bytes_returned = 0;
+ int resp_buf_type = 0;
__u16 params, param_offset, offset, byte_count, count;
+ struct kvec iov[1];
cFYI(1, ("Posix Lock"));
parm_data->lock_type = cpu_to_le16(lock_type);
if (waitFlag) {
- timeout = 3; /* blocking operation, no timeout */
+ timeout = CIFS_BLOCKING_OP; /* blocking operation, no timeout */
parm_data->lock_flags = cpu_to_le16(1);
pSMB->Timeout = cpu_to_le32(-1);
} else
rc = SendReceiveBlockingLock(xid, tcon, (struct smb_hdr *) pSMB,
(struct smb_hdr *) pSMBr, &bytes_returned);
} else {
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, timeout);
+ iov[0].iov_base = (char *)pSMB;
+ iov[0].iov_len = pSMB->hdr.smb_buf_length + 4;
+ rc = SendReceive2(xid, tcon->ses, iov, 1 /* num iovecs */,
+ &resp_buf_type, timeout);
+ pSMB = NULL; /* request buf already freed by SendReceive2. Do
+ not try to free it twice below on exit */
+ pSMBr = (struct smb_com_transaction2_sfi_rsp *)iov[0].iov_base;
}
if (rc) {
if (pSMB)
cifs_small_buf_release(pSMB);
+ if (resp_buf_type == CIFS_SMALL_BUFFER)
+ cifs_small_buf_release(iov[0].iov_base);
+ else if (resp_buf_type == CIFS_LARGE_BUFFER)
+ cifs_buf_release(iov[0].iov_base);
+
/* Note: On -EAGAIN error only caller can retry on handle based calls
since file handle passed in no longer valid */
{
int rc = 0;
CLOSE_REQ *pSMB = NULL;
- CLOSE_RSP *pSMBr = NULL;
- int bytes_returned;
cFYI(1, ("In CIFSSMBClose"));
/* do not retry on dead session on close */
if (rc)
return rc;
- pSMBr = (CLOSE_RSP *)pSMB; /* BB removeme BB */
-
pSMB->FileID = (__u16) smb_file_id;
pSMB->LastWriteTime = 0xFFFFFFFF;
pSMB->ByteCount = 0;
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 0);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *) pSMB, 0);
cifs_stats_inc(&tcon->num_closes);
if (rc) {
if (rc != -EINTR) {
}
}
- cifs_small_buf_release(pSMB);
-
/* Since session is dead, file will be closed on server already */
if (rc == -EAGAIN)
rc = 0;
iov[0].iov_len = pSMB->hdr.smb_buf_length + 4;
rc = SendReceive2(xid, tcon->ses, iov, 1 /* num iovec */, &buf_type,
- 0 /* not long op */, 0 /* do not log STATUS codes */ );
+ CIFS_STD_OP);
cifs_stats_inc(&tcon->num_acl_get);
if (rc) {
cFYI(1, ("Send error in QuerySecDesc = %d", rc));
{
int rc = 0;
FINDCLOSE_REQ *pSMB = NULL;
- CLOSE_RSP *pSMBr = NULL; /* BB removeme BB */
- int bytes_returned;
cFYI(1, ("In CIFSSMBFindClose"));
rc = small_smb_init(SMB_COM_FIND_CLOSE2, 1, tcon, (void **)&pSMB);
if (rc)
return rc;
- pSMBr = (CLOSE_RSP *)pSMB; /* BB removeme BB */
pSMB->FileID = searchHandle;
pSMB->ByteCount = 0;
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 0);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *) pSMB, 0);
if (rc) {
cERROR(1, ("Send error in FindClose = %d", rc));
}
cifs_stats_inc(&tcon->num_fclose);
- cifs_small_buf_release(pSMB);
/* Since session is dead, search handle closed on server already */
if (rc == -EAGAIN)
__u16 fid, __u32 pid_of_opener, int SetAllocation)
{
struct smb_com_transaction2_sfi_req *pSMB = NULL;
- struct smb_com_transaction2_sfi_rsp *pSMBr = NULL;
char *data_offset;
struct file_end_of_file_info *parm_data;
int rc = 0;
- int bytes_returned = 0;
__u16 params, param_offset, offset, byte_count, count;
cFYI(1, ("SetFileSize (via SetFileInfo) %lld",
if (rc)
return rc;
- pSMBr = (struct smb_com_transaction2_sfi_rsp *)pSMB;
-
pSMB->hdr.Pid = cpu_to_le16((__u16)pid_of_opener);
pSMB->hdr.PidHigh = cpu_to_le16((__u16)(pid_of_opener >> 16));
pSMB->Reserved4 = 0;
pSMB->hdr.smb_buf_length += byte_count;
pSMB->ByteCount = cpu_to_le16(byte_count);
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 0);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *) pSMB, 0);
if (rc) {
cFYI(1,
("Send error in SetFileInfo (SetFileSize) = %d",
rc));
}
- if (pSMB)
- cifs_small_buf_release(pSMB);
-
/* Note: On -EAGAIN error only caller can retry on handle based calls
since file handle passed in no longer valid */
const FILE_BASIC_INFO *data, __u16 fid)
{
struct smb_com_transaction2_sfi_req *pSMB = NULL;
- struct smb_com_transaction2_sfi_rsp *pSMBr = NULL;
char *data_offset;
int rc = 0;
- int bytes_returned = 0;
__u16 params, param_offset, offset, byte_count, count;
cFYI(1, ("Set Times (via SetFileInfo)"));
if (rc)
return rc;
- pSMBr = (struct smb_com_transaction2_sfi_rsp *)pSMB;
-
/* At this point there is no need to override the current pid
with the pid of the opener, but that could change if we someday
use an existing handle (rather than opening one on the fly) */
pSMB->hdr.smb_buf_length += byte_count;
pSMB->ByteCount = cpu_to_le16(byte_count);
memcpy(data_offset, data, sizeof(FILE_BASIC_INFO));
- rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, 0);
+ rc = SendReceiveNoRsp(xid, tcon->ses, (struct smb_hdr *) pSMB, 0);
if (rc) {
cFYI(1, ("Send error in Set Time (SetFileInfo) = %d", rc));
}
- cifs_small_buf_release(pSMB);
-
/* Note: On -EAGAIN error only caller can retry on handle based calls
since file handle passed in no longer valid */
pSMB->ByteCount = 0;
rc = SendReceive(xid, tcon->ses, (struct smb_hdr *) pSMB,
- (struct smb_hdr *) pSMBr, &bytes_returned, -1);
+ (struct smb_hdr *)pSMBr, &bytes_returned,
+ CIFS_ASYNC_OP);
if (rc) {
cFYI(1, ("Error in Notify = %d", rc));
} else {
csocket = server->ssocket;
wake_up(&server->response_q);
continue;
- } else if (length < 4) {
- cFYI(1, ("less than four bytes received (%d bytes)",
- length));
+ } else if (length < pdu_length) {
+ cFYI(1, ("requested %d bytes but only got %d bytes",
+ pdu_length, length));
pdu_length -= length;
msleep(1);
goto incomplete_rcv;
}
write_unlock(&GlobalSMBSeslock);
+ kfree(server->hostname);
kfree(server);
if (length > 0)
mempool_resize(cifs_req_poolp, length + cifs_min_rcv,
return 0;
}
+/* extract the host portion of the UNC string */
+static char *
+extract_hostname(const char *unc)
+{
+ const char *src;
+ char *dst, *delim;
+ unsigned int len;
+
+ /* skip double chars at beginning of string */
+ /* BB: check validity of these bytes? */
+ src = unc + 2;
+
+ /* delimiter between hostname and sharename is always '\\' now */
+ delim = strchr(src, '\\');
+ if (!delim)
+ return ERR_PTR(-EINVAL);
+
+ len = delim - src;
+ dst = kmalloc((len + 1), GFP_KERNEL);
+ if (dst == NULL)
+ return ERR_PTR(-ENOMEM);
+
+ memcpy(dst, src, len);
+ dst[len] = '\0';
+
+ return dst;
+}
+
static int
cifs_parse_mount_options(char *options, const char *devname,
struct smb_vol *vol)
memset(&volume_info, 0, sizeof(struct smb_vol));
if (cifs_parse_mount_options(mount_data, devname, &volume_info)) {
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
if (volume_info.nullauth) {
cifserror("No username specified");
/* In userspace mount helper we can get user name from alternate
locations such as env variables and files on disk */
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
if (volume_info.UNCip && volume_info.UNC) {
if (rc <= 0) {
/* we failed translating address */
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
cFYI(1, ("UNC: %s ip: %s", volume_info.UNC, volume_info.UNCip));
/* BB using ip addr as server name to connect to the
DFS root below */
cERROR(1, ("Connecting to DFS root not implemented yet"));
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
} else /* which servers DFS root would we conect to */ {
cERROR(1,
("CIFS mount error: No UNC path (e.g. -o "
"unc=//192.168.1.100/public) specified"));
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
/* this is needed for ASCII cp to Unicode converts */
if (cifs_sb->local_nls == NULL) {
cERROR(1, ("CIFS mount error: iocharset %s not found",
volume_info.iocharset));
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -ELIBACC;
+ rc = -ELIBACC;
+ goto out;
}
}
&sin_server6.sin6_addr,
volume_info.username, &srvTcp);
} else {
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
if (srvTcp) {
"Aborting operation"));
if (csocket != NULL)
sock_release(csocket);
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return rc;
+ goto out;
}
srvTcp = kzalloc(sizeof(struct TCP_Server_Info), GFP_KERNEL);
if (!srvTcp) {
rc = -ENOMEM;
sock_release(csocket);
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return rc;
+ goto out;
} else {
memcpy(&srvTcp->addr.sockAddr, &sin_server,
sizeof(struct sockaddr_in));
/* BB Add code for ipv6 case too */
srvTcp->ssocket = csocket;
srvTcp->protocolType = IPV4;
+ srvTcp->hostname = extract_hostname(volume_info.UNC);
+ if (IS_ERR(srvTcp->hostname)) {
+ rc = PTR_ERR(srvTcp->hostname);
+ sock_release(csocket);
+ goto out;
+ }
init_waitqueue_head(&srvTcp->response_q);
init_waitqueue_head(&srvTcp->request_q);
INIT_LIST_HEAD(&srvTcp->pending_mid_q);
srvTcp->tcpStatus = CifsNew;
init_MUTEX(&srvTcp->tcpSem);
srvTcp->tsk = kthread_run((void *)(void *)cifs_demultiplex_thread, srvTcp, "cifsd");
- if ( IS_ERR(srvTcp->tsk) ) {
+ if (IS_ERR(srvTcp->tsk)) {
rc = PTR_ERR(srvTcp->tsk);
cERROR(1, ("error %d create cifsd thread", rc));
srvTcp->tsk = NULL;
sock_release(csocket);
- kfree(volume_info.UNC);
- kfree(volume_info.password);
- kfree(volume_info.prepath);
- FreeXid(xid);
- return rc;
+ kfree(srvTcp->hostname);
+ goto out;
}
wait_for_completion(&cifsd_complete);
rc = 0;
if (existingCifsSes) {
pSesInfo = existingCifsSes;
cFYI(1, ("Existing smb sess found"));
- kfree(volume_info.password);
- /* volume_info.UNC freed at end of function */
} else if (!rc) {
cFYI(1, ("Existing smb sess not found"));
pSesInfo = sesInfoAlloc();
if (!rc) {
/* volume_info.password freed at unmount */
- if (volume_info.password)
+ if (volume_info.password) {
pSesInfo->password = volume_info.password;
+ /* set to NULL to prevent freeing on exit */
+ volume_info.password = NULL;
+ }
if (volume_info.username)
strncpy(pSesInfo->userName,
volume_info.username,
up(&pSesInfo->sesSem);
if (!rc)
atomic_inc(&srvTcp->socketUseCount);
- } else
- kfree(volume_info.password);
+ }
}
/* search for existing tcon to this server share */
"", cifs_sb->local_nls,
cifs_sb->mnt_cifs_flags &
CIFS_MOUNT_MAP_SPECIAL_CHR);
- kfree(volume_info.UNC);
- FreeXid(xid);
- return -ENODEV;
+ rc = -ENODEV;
+ goto out;
} else {
/* BB Do we need to wrap sesSem around
* this TCon call and Unix SetFS as
(in which case it is not needed anymore) but when new sesion is created
the password ptr is put in the new session structure (in which case the
password will be freed at unmount time) */
+out:
+ /* zero out password before freeing */
+ if (volume_info.password != NULL) {
+ memset(volume_info.password, 0, strlen(volume_info.password));
+ kfree(volume_info.password);
+ }
kfree(volume_info.UNC);
kfree(volume_info.prepath);
FreeXid(xid);
pSMB->req_no_secext.ByteCount = cpu_to_le16(count);
rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response,
- &bytes_returned, 1);
+ &bytes_returned, CIFS_LONG_OP);
if (rc) {
/* rc = map_smb_to_linux_error(smb_buffer_response); now done in SendReceive */
} else if ((smb_buffer_response->WordCount == 3)
pSMB->req.ByteCount = cpu_to_le16(count);
rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response,
- &bytes_returned, 1);
+ &bytes_returned, CIFS_LONG_OP);
if (smb_buffer_response->Status.CifsError ==
cpu_to_le32(NT_STATUS_MORE_PROCESSING_REQUIRED))
pSMB->req.ByteCount = cpu_to_le16(count);
rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response,
- &bytes_returned, 1);
+ &bytes_returned, CIFS_LONG_OP);
if (rc) {
/* rc = map_smb_to_linux_error(smb_buffer_response) done in SendReceive now */
} else if ((smb_buffer_response->WordCount == 3) ||
pSMB->hdr.smb_buf_length += count;
pSMB->ByteCount = cpu_to_le16(count);
- rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response, &length, 0);
+ rc = SendReceive(xid, ses, smb_buffer, smb_buffer_response, &length,
+ CIFS_STD_OP);
/* if (rc) rc = map_smb_to_linux_error(smb_buffer_response); */
/* above now done in SendReceive */
if (file->f_path.dentry->d_inode->i_mapping) {
/* BB no need to lock inode until after invalidate
since namei code should already have it locked? */
- filemap_write_and_wait(file->f_path.dentry->d_inode->i_mapping);
+ rc = filemap_write_and_wait(file->f_path.dentry->d_inode->i_mapping);
+ if (rc != 0)
+ CIFS_I(file->f_path.dentry->d_inode)->write_behind_rc = rc;
}
cFYI(1, ("invalidating remote inode since open detected it "
"changed"));
pCifsInode = CIFS_I(inode);
if (pCifsInode) {
if (can_flush) {
- filemap_write_and_wait(inode->i_mapping);
+ rc = filemap_write_and_wait(inode->i_mapping);
+ if (rc != 0)
+ CIFS_I(inode)->write_behind_rc = rc;
/* temporarily disable caching while we
go to server to get inode info */
pCifsInode->clientCanCacheAll = FALSE;
xid = GetXid();
if (*poffset > file->f_path.dentry->d_inode->i_size)
- long_op = 2; /* writes past end of file can take a long time */
+ long_op = CIFS_VLONG_OP; /* writes past EOF take long time */
else
- long_op = 1;
+ long_op = CIFS_LONG_OP;
for (total_written = 0; write_size > total_written;
total_written += bytes_written) {
}
} else
*poffset += bytes_written;
- long_op = FALSE; /* subsequent writes fast -
+ long_op = CIFS_STD_OP; /* subsequent writes fast -
15 seconds is plenty */
}
xid = GetXid();
if (*poffset > file->f_path.dentry->d_inode->i_size)
- long_op = 2; /* writes past end of file can take a long time */
+ long_op = CIFS_VLONG_OP; /* writes past EOF can be slow */
else
- long_op = 1;
+ long_op = CIFS_LONG_OP;
for (total_written = 0; write_size > total_written;
total_written += bytes_written) {
}
} else
*poffset += bytes_written;
- long_op = FALSE; /* subsequent writes fast -
+ long_op = CIFS_STD_OP; /* subsequent writes fast -
15 seconds is plenty */
}
read_unlock(&GlobalSMBSeslock);
return open_file;
}
-
+
read_unlock(&GlobalSMBSeslock);
/* Had to unlock since following call can block */
rc = cifs_reopen_file(open_file->pfile, FALSE);
- if (!rc) {
+ if (!rc) {
if (!open_file->closePend)
return open_file;
else { /* start over in case this was deleted */
/* can not use this handle, no write
pending on this one after all */
atomic_dec(&open_file->wrtPending);
-
+
if (open_file->closePend) /* list could have changed */
goto refind_writable;
/* else we simply continue to the next entry. Thus
open_file->netfid,
bytes_to_write, offset,
&bytes_written, iov, n_iov,
- 1);
+ CIFS_LONG_OP);
atomic_dec(&open_file->wrtPending);
if (rc || bytes_written < bytes_to_write) {
cERROR(1, ("Write2 ret %d, wrote %d",
rc, bytes_written));
/* BB what if continued retry is
requested via mount flags? */
- set_bit(AS_EIO, &mapping->flags);
+ if (rc == -ENOSPC)
+ set_bit(AS_ENOSPC, &mapping->flags);
+ else
+ set_bit(AS_EIO, &mapping->flags);
} else {
cifs_stats_bytes_written(cifs_sb->tcon,
bytes_written);
cFYI(1, ("Sync file - name: %s datasync: 0x%x",
dentry->d_name.name, datasync));
- rc = filemap_fdatawrite(inode->i_mapping);
- if (rc == 0)
+ rc = filemap_write_and_wait(inode->i_mapping);
+ if (rc == 0) {
+ rc = CIFS_I(inode)->write_behind_rc;
CIFS_I(inode)->write_behind_rc = 0;
+ }
FreeXid(xid);
return rc;
}
filemapfdatawrite appears easier for the time being */
rc = filemap_fdatawrite(inode->i_mapping);
- if (!rc) /* reset wb rc if we were able to write out dirty pages */
+ /* reset wb rc if we were able to write out dirty pages */
+ if (!rc) {
+ rc = CIFS_I(inode)->write_behind_rc;
CIFS_I(inode)->write_behind_rc = 0;
+ }
cFYI(1, ("Flush inode %p file %p rc %d", inode, file, rc));
int cifs_revalidate(struct dentry *direntry)
{
int xid;
- int rc = 0;
+ int rc = 0, wbrc = 0;
char *full_path;
struct cifs_sb_info *cifs_sb;
struct cifsInodeInfo *cifsInode;
if (direntry->d_inode->i_mapping) {
/* do we need to lock inode until after invalidate completes
below? */
- filemap_fdatawrite(direntry->d_inode->i_mapping);
+ wbrc = filemap_fdatawrite(direntry->d_inode->i_mapping);
+ if (wbrc)
+ CIFS_I(direntry->d_inode)->write_behind_rc = wbrc;
}
if (invalidate_inode) {
/* shrink_dcache not necessary now that cifs dentry ops
shrink_dcache_parent(direntry); */
if (S_ISREG(direntry->d_inode->i_mode)) {
if (direntry->d_inode->i_mapping)
- filemap_fdatawait(direntry->d_inode->i_mapping);
+ wbrc = filemap_fdatawait(direntry->d_inode->i_mapping);
+ if (wbrc)
+ CIFS_I(direntry->d_inode)->write_behind_rc = wbrc;
/* may eventually have to do this for open files too */
if (list_empty(&(cifsInode->openFileList))) {
/* changed on server - flush read ahead pages */
/* BB check if we need to refresh inode from server now ? BB */
- /* need to flush data before changing file size on server */
- filemap_write_and_wait(direntry->d_inode->i_mapping);
-
if (attrs->ia_valid & ATTR_SIZE) {
+ /*
+ Flush data before changing file size on server. If the
+ flush returns error, store it to report later and continue.
+ BB: This should be smarter. Why bother flushing pages that
+ will be truncated anyway? Also, should we error out here if
+ the flush returns error?
+ */
+ rc = filemap_write_and_wait(direntry->d_inode->i_mapping);
+ if (rc != 0) {
+ CIFS_I(direntry->d_inode)->write_behind_rc = rc;
+ rc = 0;
+ }
+
/* To avoid spurious oplock breaks from server, in the case of
inodes that we already have open, avoid doing path based
setting of file size if we can do it by handle.
#include "ntlmssp.h"
#include "nterr.h"
#include <linux/utsname.h>
+#include "cifs_spnego.h"
extern void SMBNTencrypt(unsigned char *passwd, unsigned char *c8,
unsigned char *p24);
SESSION_SETUP_ANDX *pSMB;
__u32 capabilities;
int count;
- int resp_buf_type = 0;
- struct kvec iov[2];
+ int resp_buf_type;
+ struct kvec iov[3];
enum securityEnum type;
__u16 action;
int bytes_remaining;
+ struct key *spnego_key = NULL;
if (ses == NULL)
return -EINVAL;
capabilities = cifs_ssetup_hdr(ses, pSMB);
- /* we will send the SMB in two pieces,
- a fixed length beginning part, and a
- second part which will include the strings
- and rest of bcc area, in order to avoid having
- to do a large buffer 17K allocation */
+ /* we will send the SMB in three pieces:
+ a fixed length beginning part, an optional
+ SPNEGO blob (which can be zero length), and a
+ last part which will include the strings
+ and rest of bcc area. This allows us to avoid
+ a large buffer 17K allocation */
iov[0].iov_base = (char *)pSMB;
iov[0].iov_len = smb_buf->smb_buf_length + 4;
+ /* setting this here allows the code at the end of the function
+ to free the request buffer if there's an error */
+ resp_buf_type = CIFS_SMALL_BUFFER;
+
/* 2000 big enough to fit max user, domain, NOS name etc. */
str_area = kmalloc(2000, GFP_KERNEL);
if (str_area == NULL) {
- cifs_small_buf_release(smb_buf);
- return -ENOMEM;
+ rc = -ENOMEM;
+ goto ssetup_exit;
}
bcc_ptr = str_area;
ses->flags &= ~CIFS_SES_LANMAN;
+ iov[1].iov_base = NULL;
+ iov[1].iov_len = 0;
+
if (type == LANMAN) {
#ifdef CONFIG_CIFS_WEAK_PW_HASH
char lnm_session_key[CIFS_SESS_KEY_SIZE];
struct ntlmv2_resp */
if (v2_sess_key == NULL) {
- cifs_small_buf_release(smb_buf);
- return -ENOMEM;
+ rc = -ENOMEM;
+ goto ssetup_exit;
}
pSMB->req_no_secext.Capabilities = cpu_to_le32(capabilities);
unicode_ssetup_strings(&bcc_ptr, ses, nls_cp);
} else
ascii_ssetup_strings(&bcc_ptr, ses, nls_cp);
- } else /* NTLMSSP or SPNEGO */ {
+ } else if (type == Kerberos) {
+#ifdef CONFIG_CIFS_UPCALL
+ struct cifs_spnego_msg *msg;
+ spnego_key = cifs_get_spnego_key(ses);
+ if (IS_ERR(spnego_key)) {
+ rc = PTR_ERR(spnego_key);
+ spnego_key = NULL;
+ goto ssetup_exit;
+ }
+
+ msg = spnego_key->payload.data;
+ /* bail out if key is too long */
+ if (msg->sesskey_len >
+ sizeof(ses->server->mac_signing_key.data.krb5)) {
+ cERROR(1, ("Kerberos signing key too long (%u bytes)",
+ msg->sesskey_len));
+ rc = -EOVERFLOW;
+ goto ssetup_exit;
+ }
+ ses->server->mac_signing_key.len = msg->sesskey_len;
+ memcpy(ses->server->mac_signing_key.data.krb5, msg->data,
+ msg->sesskey_len);
pSMB->req.hdr.Flags2 |= SMBFLG2_EXT_SEC;
capabilities |= CAP_EXTENDED_SECURITY;
pSMB->req.Capabilities = cpu_to_le32(capabilities);
- /* BB set password lengths */
+ iov[1].iov_base = msg->data + msg->sesskey_len;
+ iov[1].iov_len = msg->secblob_len;
+ pSMB->req.SecurityBlobLength = cpu_to_le16(iov[1].iov_len);
+
+ if (ses->capabilities & CAP_UNICODE) {
+ /* unicode strings must be word aligned */
+ if (iov[0].iov_len % 2) {
+ *bcc_ptr = 0;
+ bcc_ptr++;
+ }
+ unicode_oslm_strings(&bcc_ptr, nls_cp);
+ unicode_domain_string(&bcc_ptr, ses, nls_cp);
+ } else
+ /* BB: is this right? */
+ ascii_ssetup_strings(&bcc_ptr, ses, nls_cp);
+#else /* ! CONFIG_CIFS_UPCALL */
+ cERROR(1, ("Kerberos negotiated but upcall support disabled!"));
+ rc = -ENOSYS;
+ goto ssetup_exit;
+#endif /* CONFIG_CIFS_UPCALL */
+ } else {
+ cERROR(1, ("secType %d not supported!", type));
+ rc = -ENOSYS;
+ goto ssetup_exit;
}
- count = (long) bcc_ptr - (long) str_area;
+ iov[2].iov_base = str_area;
+ iov[2].iov_len = (long) bcc_ptr - (long) str_area;
+
+ count = iov[1].iov_len + iov[2].iov_len;
smb_buf->smb_buf_length += count;
BCC_LE(smb_buf) = cpu_to_le16(count);
- iov[1].iov_base = str_area;
- iov[1].iov_len = count;
- rc = SendReceive2(xid, ses, iov, 2 /* num_iovecs */, &resp_buf_type,
- 0 /* not long op */, 1 /* log NT STATUS if any */ );
+ rc = SendReceive2(xid, ses, iov, 3 /* num_iovecs */, &resp_buf_type,
+ CIFS_STD_OP /* not long */ | CIFS_LOG_ERROR);
/* SMB request buf freed in SendReceive2 */
cFYI(1, ("ssetup rc from sendrecv2 is %d", rc));
ses, nls_cp);
ssetup_exit:
+ if (spnego_key)
+ key_put(spnego_key);
kfree(str_area);
if (resp_buf_type == CIFS_SMALL_BUFFER) {
cFYI(1, ("ssetup freeing small buf %p", iov[0].iov_base));
static int wait_for_free_request(struct cifsSesInfo *ses, const int long_op)
{
- if (long_op == -1) {
+ if (long_op == CIFS_ASYNC_OP) {
/* oplock breaks must not be held up */
atomic_inc(&ses->server->inFlight);
} else {
as they are allowed to block on server */
/* update # of requests on the wire to server */
- if (long_op < 3)
+ if (long_op != CIFS_BLOCKING_OP)
atomic_inc(&ses->server->inFlight);
spin_unlock(&GlobalMid_Lock);
break;
}
}
+
+/*
+ *
+ * Send an SMB Request. No response info (other than return code)
+ * needs to be parsed.
+ *
+ * flags indicate the type of request buffer and how long to wait
+ * and whether to log NT STATUS code (error) before mapping it to POSIX error
+ *
+ */
+int
+SendReceiveNoRsp(const unsigned int xid, struct cifsSesInfo *ses,
+ struct smb_hdr *in_buf, int flags)
+{
+ int rc;
+ struct kvec iov[1];
+ int resp_buf_type;
+
+ iov[0].iov_base = (char *)in_buf;
+ iov[0].iov_len = in_buf->smb_buf_length + 4;
+ flags |= CIFS_NO_RESP;
+ rc = SendReceive2(xid, ses, iov, 1, &resp_buf_type, flags);
+#ifdef CONFIG_CIFS_DEBUG2
+ cFYI(1, ("SendRcvNoR flags %d rc %d", flags, rc));
+#endif
+ return rc;
+}
+
int
SendReceive2(const unsigned int xid, struct cifsSesInfo *ses,
struct kvec *iov, int n_vec, int *pRespBufType /* ret */,
- const int long_op, const int logError)
+ const int flags)
{
int rc = 0;
+ int long_op;
unsigned int receive_len;
unsigned long timeout;
struct mid_q_entry *midQ;
struct smb_hdr *in_buf = iov[0].iov_base;
+ long_op = flags & CIFS_TIMEOUT_MASK;
+
*pRespBufType = CIFS_NO_BUFFER; /* no response buf yet */
if ((ses == NULL) || (ses->server == NULL)) {
if (rc < 0)
goto out;
- if (long_op == -1)
- goto out;
- else if (long_op == 2) /* writes past end of file can take loong time */
+ if (long_op == CIFS_STD_OP)
+ timeout = 15 * HZ;
+ else if (long_op == CIFS_VLONG_OP) /* e.g. slow writes past EOF */
timeout = 180 * HZ;
- else if (long_op == 1)
+ else if (long_op == CIFS_LONG_OP)
timeout = 45 * HZ; /* should be greater than
servers oplock break timeout (about 43 seconds) */
- else
- timeout = 15 * HZ;
+ else if (long_op == CIFS_ASYNC_OP)
+ goto out;
+ else if (long_op == CIFS_BLOCKING_OP)
+ timeout = 0x7FFFFFFF; /* large, but not so large as to wrap */
+ else {
+ cERROR(1, ("unknown timeout flag %d", long_op));
+ rc = -EIO;
+ goto out;
+ }
/* wait for 15 seconds or until woken up due to response arriving or
due to last connection to this server being unmounted */
}
/* BB special case reconnect tid and uid here? */
- rc = map_smb_to_linux_error(midQ->resp_buf, logError);
+ rc = map_smb_to_linux_error(midQ->resp_buf,
+ flags & CIFS_LOG_ERROR);
/* convert ByteCount if necessary */
if (receive_len >= sizeof(struct smb_hdr) - 4
(2 * midQ->resp_buf->WordCount) + 2 /* bcc */ )
BCC(midQ->resp_buf) =
le16_to_cpu(BCC_LE(midQ->resp_buf));
- midQ->resp_buf = NULL; /* mark it so will not be freed
- by DeleteMidQEntry */
+ if ((flags & CIFS_NO_RESP) == 0)
+ midQ->resp_buf = NULL; /* mark it so buf will
+ not be freed by
+ DeleteMidQEntry */
} else {
rc = -EIO;
cFYI(1, ("Bad MID state?"));
if (rc < 0)
goto out;
- if (long_op == -1)
+ if (long_op == CIFS_STD_OP)
+ timeout = 15 * HZ;
+ /* wait for 15 seconds or until woken up due to response arriving or
+ due to last connection to this server being unmounted */
+ else if (long_op == CIFS_ASYNC_OP)
goto out;
- else if (long_op == 2) /* writes past end of file can take loong time */
+ else if (long_op == CIFS_VLONG_OP) /* writes past EOF can be slow */
timeout = 180 * HZ;
- else if (long_op == 1)
+ else if (long_op == CIFS_LONG_OP)
timeout = 45 * HZ; /* should be greater than
servers oplock break timeout (about 43 seconds) */
- else
- timeout = 15 * HZ;
- /* wait for 15 seconds or until woken up due to response arriving or
- due to last connection to this server being unmounted */
+ else if (long_op == CIFS_BLOCKING_OP)
+ timeout = 0x7FFFFFFF; /* large but no so large as to wrap */
+ else {
+ cERROR(1, ("unknown timeout flag %d", long_op));
+ rc = -EIO;
+ goto out;
+ }
+
if (signal_pending(current)) {
/* if signal pending do not hold up user for full smb timeout
but we still give response a chance to complete */
pSMB->hdr.Mid = GetNextMid(ses->server);
return SendReceive(xid, ses, in_buf, out_buf,
- &bytes_returned, 0);
+ &bytes_returned, CIFS_STD_OP);
}
int
to the same server. We may make this configurable later or
use ses->maxReq */
- rc = wait_for_free_request(ses, 3);
+ rc = wait_for_free_request(ses, CIFS_BLOCKING_OP);
if (rc)
return rc;
struct acpi_processor_power {
struct cpuidle_device dev;
struct acpi_processor_cx *state;
- struct acpi_processor_cx *bm_state;
unsigned long bm_check_timestamp;
u32 default_state;
u32 bm_activity;
+++ /dev/null
-/*
- * 8253/8254 Programmable Interval Timer
- */
-
-#ifndef _8253PIT_H
-#define _8253PIT_H
-
-#define PIT_TICK_RATE 1193182UL
-
-#endif
#define MAX_DMA_ADDRESS (PAGE_OFFSET + 0x01000000)
#endif
#define MAX_DMA_PFN PFN_DOWN(virt_to_phys((void *)MAX_DMA_ADDRESS))
+#define MAX_DMA32_PFN (1UL << (32 - PAGE_SHIFT))
/* 8237 DMA controllers */
#define IO_DMA1_BASE 0x00 /* 8 bit slave DMA, channels 0..3 */
" .set mips0 \n" \
" .section .fixup,\"ax\" \n" \
"4: li %0, %6 \n" \
- " j 2b \n" \
+ " j 3b \n" \
" .previous \n" \
" .section __ex_table,\"a\" \n" \
" "__UA_ADDR "\t1b, 4b \n" \
" .set mips0 \n" \
" .section .fixup,\"ax\" \n" \
"4: li %0, %6 \n" \
- " j 2b \n" \
+ " j 3b \n" \
" .previous \n" \
" .section __ex_table,\"a\" \n" \
" "__UA_ADDR "\t1b, 4b \n" \
}
#endif
-#endif
+#endif /* _ASM_FUTEX_H */
#define PIT_CH0 0x40
#define PIT_CH2 0x42
+#define PIT_TICK_RATE 1193182UL
+
extern spinlock_t i8253_lock;
extern void setup_pit_timer(void);
* CPU interrupts are 0 ... 7
*/
- CRIME_IRQ_BASE = MIPS_CPU_IRQ_BASE,
+ CRIME_IRQ_BASE = MIPS_CPU_IRQ_BASE + 8,
/*
* MACE
if (cpu_has_dsp) \
__save_dsp(prev); \
(last) = resume(prev, next, task_thread_info(next)); \
+} while (0)
+
+#define finish_arch_switch(prev) \
+do { \
if (cpu_has_dsp) \
__restore_dsp(current); \
if (cpu_has_userlocal) \
- write_c0_userlocal(task_thread_info(current)->tp_value);\
-} while(0)
+ write_c0_userlocal(current_thread_info()->tp_value); \
+} while (0)
static inline unsigned long __xchg_u32(volatile int * m, unsigned int val)
{
* Initialize the calling CPU's compare interrupt as clockevent device
*/
#ifdef CONFIG_CEVT_R4K
-extern void mips_clockevent_init(void);
+extern int mips_clockevent_init(void);
extern unsigned int __weak get_c0_compare_int(void);
#else
-static inline void mips_clockevent_init(void)
+static inline int mips_clockevent_init(void)
+{
+ return -ENXIO;
+}
+#endif
+
+/*
+ * Initialize the count register as a clocksource
+ */
+#ifdef CONFIG_CEVT_R4K
+extern void init_mips_clocksource(void);
+#else
+static inline void init_mips_clocksource(void)
{
}
#endif
#define PPC_MEMSTART 0
+#ifdef CONFIG_NOT_COHERENT_CACHE
+#define ARCH_KMALLOC_MINALIGN L1_CACHE_BYTES
+#endif
+
#ifndef __ASSEMBLY__
/*
* The basic type of a PTE - 64 bits for those CPUs with > 32 bit
return PCI_DN(busdn)->phb;
}
-extern void pcibios_free_controller(struct pci_controller *phb);
extern void isa_bridge_find_early(struct pci_controller *hose);
pci_process_bridge_OF_ranges(struct pci_controller *hose,
struct device_node *dev, int primary);
-/* Allocate a new PCI host bridge structure */
+/* Allocate & free a PCI host bridge structure */
extern struct pci_controller *
pcibios_alloc_controller(struct device_node *dev);
+extern void pcibios_free_controller(struct pci_controller *phb);
+
#ifdef CONFIG_PCI
extern unsigned long pci_address_to_pio(phys_addr_t address);
extern int pcibios_vaddr_is_ioport(void __iomem *address);
extern void rtas_restart(char *cmd);
extern void rtas_power_off(void);
extern void rtas_halt(void);
-extern void rtas_os_term(char *str);
+extern void rtas_panic_msg(char *str);
+extern void rtas_os_term(void);
extern int rtas_get_sensor(int sensor, int index, int *state);
extern int rtas_get_power_level(int powerdomain, int *level);
extern int rtas_set_power_level(int powerdomain, int level, int *setlevel);
/* those additional ones don't have to be located anywhere
* special as they were not part of the original systemcfg
*/
+ __u32 dcache_block_size; /* L1 d-cache block size */
+ __u32 icache_block_size; /* L1 i-cache block size */
+ __u32 dcache_log_block_size; /* L1 d-cache log block size */
+ __u32 icache_log_block_size; /* L1 i-cache log block size */
__s32 wtom_clock_sec; /* Wall to monotonic clock */
__s32 wtom_clock_nsec;
__u32 syscall_map_64[SYSCALL_MAP_SIZE]; /* map of syscalls */
__s32 wtom_clock_sec; /* Wall to monotonic clock */
__s32 wtom_clock_nsec;
__u32 syscall_map_32[SYSCALL_MAP_SIZE]; /* map of syscalls */
+ __u32 dcache_block_size; /* L1 d-cache block size */
+ __u32 icache_block_size; /* L1 i-cache block size */
+ __u32 dcache_log_block_size; /* L1 d-cache log block size */
+ __u32 icache_log_block_size; /* L1 i-cache log block size */
};
#endif /* CONFIG_PPC64 */
#define arch_align_stack(x) (x)
+#ifdef CONFIG_TRACE_IRQFLAGS
+extern psw_t sysc_restore_trace_psw;
+extern psw_t io_restore_trace_psw;
+#endif
+
#endif /* __KERNEL__ */
#endif
int acpi_register_gsi (u32 gsi, int triggering, int polarity);
int acpi_gsi_to_irq (u32 gsi, unsigned int *irq);
+#ifdef CONFIG_X86_IO_APIC
+extern int acpi_get_override_irq(int bus_irq, int *trigger, int *polarity);
+#else
+#define acpi_get_override_irq(bus, trigger, polarity) (-1)
+#endif
/*
* This function undoes the effect of one call to acpi_register_gsi().
* If this matches the last registration, any IRQ resources for gsi
struct kobject kobj;
struct completion kobj_unregister;
void *governor_data;
+ struct cpuidle_state *safe_state;
};
DECLARE_PER_CPU(struct cpuidle_device *, cpuidle_devices);
ATA_HORKAGE_HPA_SIZE = (1 << 6), /* native size off by one */
ATA_HORKAGE_IPM = (1 << 7), /* Link PM problems */
ATA_HORKAGE_IVB = (1 << 8), /* cbl det validity bit bugs */
+ ATA_HORKAGE_STUCK_ERR = (1 << 9), /* stuck ERR on next PACKET */
/* DMA mask for user DMA control: User visible values; DO NOT
renumber */
extern void sata_print_link_status(struct ata_link *link);
extern void ata_port_probe(struct ata_port *);
-extern void __sata_phy_reset(struct ata_port *ap);
-extern void sata_phy_reset(struct ata_port *ap);
extern void ata_bus_reset(struct ata_port *ap);
extern int sata_set_spd(struct ata_link *link);
extern int sata_link_debounce(struct ata_link *link,
/*
* EH
*/
-extern void ata_eng_timeout(struct ata_port *ap);
-
extern void ata_port_schedule_eh(struct ata_port *ap);
extern int ata_link_abort(struct ata_link *link);
extern int ata_port_abort(struct ata_port *ap);
CTL_ABI=9, /* Binary emulation */
CTL_CPU=10, /* CPU stuff (speed scaling, etc) */
CTL_ARLAN=254, /* arlan wireless driver */
- CTL_APPLDATA=2120, /* s390 appldata */
CTL_S390DBF=5677, /* s390 debug */
CTL_SUNRPC=7249, /* sunrpc debug */
CTL_PM=9899, /* frv power management */
VM_PANIC_ON_OOM=33, /* panic at out-of-memory */
VM_VDSO_ENABLED=34, /* map VDSO into new processes? */
VM_MIN_SLAB=35, /* Percent pages ignored by zone reclaim */
-
- /* s390 vm cmm sysctls */
- VM_CMM_PAGES=1111,
- VM_CMM_TIMED_PAGES=1112,
- VM_CMM_TIMEOUT=1113,
};
/* include/version.h. Generated by alsa/ksync script. */
#define CONFIG_SND_VERSION "1.0.15"
-#define CONFIG_SND_DATE " (Tue Oct 23 06:09:18 2007 UTC)"
+#define CONFIG_SND_DATE " (Tue Nov 20 19:16:42 2007 UTC)"
}
EXPORT_SYMBOL(unregister_module_notifier);
-/* We require a truly strong try_module_get() */
+/* We require a truly strong try_module_get(): 0 means failure due to
+ ongoing or failed initialization etc. */
static inline int strong_try_module_get(struct module *mod)
{
if (mod && mod->state == MODULE_STATE_COMING)
ret = __find_symbol(name, &owner, &crc,
!(mod->taints & TAINT_PROPRIETARY_MODULE));
if (ret) {
- /* use_module can fail due to OOM, or module unloading */
+ /* use_module can fail due to OOM,
+ or module initialization or unloading */
if (!check_version(sechdrs, versindex, name, mod, crc) ||
!use_module(mod, owner))
ret = 0;
return ret;
}
-/* Change all symbols so that sh_value encodes the pointer directly. */
+/* Change all symbols so that st_value encodes the pointer directly. */
static int simplify_symbols(Elf_Shdr *sechdrs,
unsigned int symindex,
const char *strtab,
{ VM_PANIC_ON_OOM, "panic_on_oom" },
{ VM_VDSO_ENABLED, "vdso_enabled" },
{ VM_MIN_SLAB, "min_slab_ratio" },
- { VM_CMM_PAGES, "cmm_pages" },
- { VM_CMM_TIMED_PAGES, "cmm_timed_pages" },
- { VM_CMM_TIMEOUT, "cmm_timeout" },
{}
};
{}
};
-static struct trans_ctl_table trans_appldata_table[] = {
- { CTL_APPLDATA_TIMER, "timer" },
- { CTL_APPLDATA_INTERVAL, "interval" },
- { CTL_APPLDATA_OS, "os" },
- { CTL_APPLDATA_NET_SUM, "net_sum" },
- { CTL_APPLDATA_MEM, "mem" },
- {}
-
-};
-
static struct trans_ctl_table trans_s390dbf_table[] = {
{ 5678 /* CTL_S390DBF_STOPPABLE */, "debug_stoppable" },
{ 5679 /* CTL_S390DBF_ACTIVE */, "debug_active" },
{ CTL_ABI, "abi" },
/* CTL_CPU not used */
{ CTL_ARLAN, "arlan", trans_arlan_table },
- { CTL_APPLDATA, "appldata", trans_appldata_table },
{ CTL_S390DBF, "s390dbf", trans_s390dbf_table },
{ CTL_SUNRPC, "sunrpc", trans_sunrpc_table },
{ CTL_PM, "pm", trans_pm_table },
if (page_mapped(page)) {
struct address_space *mapping = page_mapping(page);
- if (mapping)
+ if (mapping) {
ret = page_mkclean_file(mapping, page);
- if (page_test_dirty(page)) {
- page_clear_dirty(page);
- ret = 1;
+ if (page_test_dirty(page)) {
+ page_clear_dirty(page);
+ ret = 1;
+ }
}
}
struct iucv_irq_data data;
};
-static struct iucv_irq_data *iucv_irq_data;
+static struct iucv_irq_data *iucv_irq_data[NR_CPUS];
static cpumask_t iucv_buffer_cpumask = CPU_MASK_NONE;
static cpumask_t iucv_irq_cpumask = CPU_MASK_NONE;
/*
* Anchor for per-cpu IUCV command parameter block.
*/
-static union iucv_param *iucv_param;
+static union iucv_param *iucv_param[NR_CPUS];
/**
* iucv_call_b2f0
* 0x10 - Flag to allow priority message completion interrupts
* 0x08 - Flag to allow IUCV control interrupts
*/
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[cpu];
memset(parm, 0, sizeof(union iucv_param));
parm->set_mask.ipmask = 0xf8;
iucv_call_b2f0(IUCV_SETMASK, parm);
union iucv_param *parm;
/* Disable all iucv interrupts. */
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[cpu];
memset(parm, 0, sizeof(union iucv_param));
iucv_call_b2f0(IUCV_SETMASK, parm);
return;
/* Declare interrupt buffer. */
- parm = percpu_ptr(iucv_param, cpu);
+ parm = iucv_param[cpu];
memset(parm, 0, sizeof(union iucv_param));
- parm->db.ipbfadr1 = virt_to_phys(percpu_ptr(iucv_irq_data, cpu));
+ parm->db.ipbfadr1 = virt_to_phys(iucv_irq_data[cpu]);
rc = iucv_call_b2f0(IUCV_DECLARE_BUFFER, parm);
if (rc) {
char *err = "Unknown";
iucv_block_cpu(NULL);
/* Retrieve interrupt buffer. */
- parm = percpu_ptr(iucv_param, cpu);
+ parm = iucv_param[cpu];
iucv_call_b2f0(IUCV_RETRIEVE_BUFFER, parm);
/* Clear indication that an iucv buffer exists for this cpu. */
switch (action) {
case CPU_UP_PREPARE:
case CPU_UP_PREPARE_FROZEN:
- if (!percpu_populate(iucv_irq_data,
- sizeof(struct iucv_irq_data),
- GFP_KERNEL|GFP_DMA, cpu))
+ iucv_irq_data[cpu] = kmalloc_node(sizeof(struct iucv_irq_data),
+ GFP_KERNEL|GFP_DMA, cpu_to_node(cpu));
+ if (!iucv_irq_data[cpu])
return NOTIFY_BAD;
- if (!percpu_populate(iucv_param, sizeof(union iucv_param),
- GFP_KERNEL|GFP_DMA, cpu)) {
- percpu_depopulate(iucv_irq_data, cpu);
+ iucv_param[cpu] = kmalloc_node(sizeof(union iucv_param),
+ GFP_KERNEL|GFP_DMA, cpu_to_node(cpu));
+ if (!iucv_param[cpu])
return NOTIFY_BAD;
- }
break;
case CPU_UP_CANCELED:
case CPU_UP_CANCELED_FROZEN:
case CPU_DEAD:
case CPU_DEAD_FROZEN:
- percpu_depopulate(iucv_param, cpu);
- percpu_depopulate(iucv_irq_data, cpu);
+ kfree(iucv_param[cpu]);
+ iucv_param[cpu] = NULL;
+ kfree(iucv_irq_data[cpu]);
+ iucv_irq_data[cpu] = NULL;
break;
case CPU_ONLINE:
case CPU_ONLINE_FROZEN:
{
union iucv_param *parm;
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (userdata)
memcpy(parm->ctrl.ipuser, userdata, sizeof(parm->ctrl.ipuser));
local_bh_disable();
/* Prepare parameter block. */
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->ctrl.ippathid = path->pathid;
parm->ctrl.ipmsglim = path->msglim;
BUG_ON(in_atomic());
spin_lock_bh(&iucv_table_lock);
iucv_cleanup_queue();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->ctrl.ipmsglim = path->msglim;
parm->ctrl.ipflags1 = path->flags;
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (userdata)
memcpy(parm->ctrl.ipuser, userdata, sizeof(parm->ctrl.ipuser));
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (userdata)
memcpy(parm->ctrl.ipuser, userdata, sizeof(parm->ctrl.ipuser));
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->purge.ippathid = path->pathid;
parm->purge.ipmsgid = msg->id;
}
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->db.ipbfadr1 = (u32)(addr_t) buffer;
parm->db.ipbfln1f = (u32) size;
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
parm->db.ippathid = path->pathid;
parm->db.ipmsgid = msg->id;
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (flags & IUCV_IPRMDATA) {
parm->dpl.ippathid = path->pathid;
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (flags & IUCV_IPRMDATA) {
/* Message of 8 bytes can be placed into the parameter list. */
int rc;
local_bh_disable();
- parm = percpu_ptr(iucv_param, smp_processor_id());
+ parm = iucv_param[smp_processor_id()];
memset(parm, 0, sizeof(union iucv_param));
if (flags & IUCV_IPRMDATA) {
parm->dpl.ippathid = path->pathid;
struct iucv_irq_data *p;
struct iucv_irq_list *work;
- p = percpu_ptr(iucv_irq_data, smp_processor_id());
+ p = iucv_irq_data[smp_processor_id()];
if (p->ippathid >= iucv_max_pathid) {
printk(KERN_WARNING "iucv_do_int: Got interrupt with "
"pathid %d > max_connections (%ld)\n",
static int __init iucv_init(void)
{
int rc;
+ int cpu;
if (!MACHINE_IS_VM) {
rc = -EPROTONOSUPPORT;
rc = PTR_ERR(iucv_root);
goto out_bus;
}
- /* Note: GFP_DMA used to get memory below 2G */
- iucv_irq_data = percpu_alloc(sizeof(struct iucv_irq_data),
- GFP_KERNEL|GFP_DMA);
- if (!iucv_irq_data) {
- rc = -ENOMEM;
- goto out_root;
- }
- /* Allocate parameter blocks. */
- iucv_param = percpu_alloc(sizeof(union iucv_param),
- GFP_KERNEL|GFP_DMA);
- if (!iucv_param) {
- rc = -ENOMEM;
- goto out_extint;
+
+ for_each_online_cpu(cpu) {
+ /* Note: GFP_DMA used to get memory below 2G */
+ iucv_irq_data[cpu] = kmalloc_node(sizeof(struct iucv_irq_data),
+ GFP_KERNEL|GFP_DMA, cpu_to_node(cpu));
+ if (!iucv_irq_data[cpu]) {
+ rc = -ENOMEM;
+ goto out_free;
+ }
+
+ /* Allocate parameter blocks. */
+ iucv_param[cpu] = kmalloc_node(sizeof(union iucv_param),
+ GFP_KERNEL|GFP_DMA, cpu_to_node(cpu));
+ if (!iucv_param[cpu]) {
+ rc = -ENOMEM;
+ goto out_free;
+ }
}
register_hotcpu_notifier(&iucv_cpu_notifier);
ASCEBC(iucv_error_no_listener, 16);
iucv_available = 1;
return 0;
-out_extint:
- percpu_free(iucv_irq_data);
-out_root:
+out_free:
+ for_each_possible_cpu(cpu) {
+ kfree(iucv_param[cpu]);
+ iucv_param[cpu] = NULL;
+ kfree(iucv_irq_data[cpu]);
+ iucv_irq_data[cpu] = NULL;
+ }
s390_root_dev_unregister(iucv_root);
out_bus:
bus_unregister(&iucv_bus);
static void __exit iucv_exit(void)
{
struct iucv_irq_list *p, *n;
+ int cpu;
spin_lock_irq(&iucv_queue_lock);
list_for_each_entry_safe(p, n, &iucv_task_queue, list)
kfree(p);
spin_unlock_irq(&iucv_queue_lock);
unregister_hotcpu_notifier(&iucv_cpu_notifier);
- percpu_free(iucv_param);
- percpu_free(iucv_irq_data);
+ for_each_possible_cpu(cpu) {
+ kfree(iucv_param[cpu]);
+ iucv_param[cpu] = NULL;
+ kfree(iucv_irq_data[cpu]);
+ iucv_irq_data[cpu] = NULL;
+ }
s390_root_dev_unregister(iucv_root);
bus_unregister(&iucv_bus);
unregister_external_interrupt(0x4000, iucv_external_interrupt);
static void uart_interrupt_tx(struct snd_mpu401 *mpu)
{
+ unsigned long flags;
+
if (test_bit(MPU401_MODE_BIT_OUTPUT, &mpu->mode) &&
test_bit(MPU401_MODE_BIT_OUTPUT_TRIGGER, &mpu->mode)) {
- spin_lock(&mpu->output_lock);
+ spin_lock_irqsave(&mpu->output_lock, flags);
snd_mpu401_uart_output_write(mpu);
- spin_unlock(&mpu->output_lock);
+ spin_unlock_irqrestore(&mpu->output_lock, flags);
}
}
static void _snd_mpu401_uart_interrupt(struct snd_mpu401 *mpu)
{
+ unsigned long flags;
+
if (mpu->info_flags & MPU401_INFO_INPUT) {
- spin_lock(&mpu->input_lock);
+ spin_lock_irqsave(&mpu->input_lock, flags);
if (test_bit(MPU401_MODE_BIT_INPUT, &mpu->mode))
snd_mpu401_uart_input_read(mpu);
else
snd_mpu401_uart_clear_rx(mpu);
- spin_unlock(&mpu->input_lock);
+ spin_unlock_irqrestore(&mpu->input_lock, flags);
}
if (! (mpu->info_flags & MPU401_INFO_TX_IRQ))
/* ok. for better Tx performance try do some output
parport_release(pardev);
parport_unregister_device(pardev);
- return res;
+ return res ? -EIO : 0;
}
static void __devinit snd_portman_attach(struct parport *p)
{
struct snd_ca0106 *emu = snd_kcontrol_chip(kcontrol);
- ucontrol->value.enumerated.item[0] = emu->spdif_enable;
+ ucontrol->value.integer.value[0] = emu->spdif_enable;
return 0;
}
int change = 0;
u32 mask;
- val = ucontrol->value.enumerated.item[0] ;
+ val = !!ucontrol->value.integer.value[0];
change = (emu->spdif_enable != val);
if (change) {
emu->spdif_enable = val;
- if (val == 1) {
+ if (val) {
/* Digital */
snd_ca0106_ptr_write(emu, SPDIF_SELECT1, 0, 0xf);
snd_ca0106_ptr_write(emu, SPDIF_SELECT2, 0, 0x0b000000);
u32 source;
val = ucontrol->value.enumerated.item[0] ;
+ if (val >= 6)
+ return -EINVAL;
change = (emu->capture_source != val);
if (change) {
emu->capture_source = val;
* for the particular source.
*/
source_id = ucontrol->value.enumerated.item[0] ;
+ if (source_id >= 4)
+ return -EINVAL;
change = (emu->i2c_capture_source != source_id);
if (change) {
snd_ca0106_i2c_write(emu, ADC_MUX, 0); /* Mute input */
u32 tmp;
val = ucontrol->value.enumerated.item[0] ;
+ if (val > 1)
+ return -EINVAL;
change = (emu->capture_mic_line_in != val);
if (change) {
emu->capture_mic_line_in = val;
ogain = emu->i2c_capture_volume[source_id][0]; /* Left */
ngain = ucontrol->value.integer.value[0];
if (ngain > 0xff)
- return 0;
+ return -EINVAL;
if (ogain != ngain) {
if (emu->i2c_capture_source == source_id)
snd_ca0106_i2c_write(emu, ADC_ATTEN_ADCL, ((ngain) & 0xff) );
ogain = emu->i2c_capture_volume[source_id][1]; /* Right */
ngain = ucontrol->value.integer.value[1];
if (ngain > 0xff)
- return 0;
+ return -EINVAL;
if (ogain != ngain) {
if (emu->i2c_capture_source == source_id)
snd_ca0106_i2c_write(emu, ADC_ATTEN_ADCR, ((ngain) & 0xff));
}
ret = snd_ca0106_spi_write(emu, emu->spi_dac_reg[reg]);
- return ret ? -1 : 1;
+ return ret ? -EINVAL : 1;
}
#define CA_VOLUME(xname,chid,reg) \
snd_info_set_text_ops(entry, emu, snd_ca0106_proc_reg_read1);
entry->c.text.write = snd_ca0106_proc_reg_write;
entry->mode |= S_IWUSR;
-// entry->private_data = emu;
}
if(! snd_card_proc_new(emu->card, "ca0106_i2c", &entry)) {
- snd_info_set_text_ops(entry, emu, snd_ca0106_proc_i2c_write);
entry->c.text.write = snd_ca0106_proc_i2c_write;
+ entry->private_data = emu;
entry->mode |= S_IWUSR;
-// entry->private_data = emu;
}
if(! snd_card_proc_new(emu->card, "ca0106_regs2", &entry))
snd_info_set_text_ops(entry, emu, snd_ca0106_proc_reg_read2);
#define CM_MMODE_MASK 0x00000E00 /* model DAA interface mode */
#define CM_SPDIF_SELECT2 0x00000100 /* for model > 039 ? */
#define CM_ENCENTER 0x00000080
-#define CM_FLINKON 0x00000080 /* force modem link detection on, model 037 */
+#define CM_FLINKON 0x00000040 /* force modem link detection on, model 037 */
#define CM_MUTECH1 0x00000040 /* mute PCI ch1 to DAC */
-#define CM_FLINKOFF 0x00000040 /* force modem link detection off, model 037 */
-#define CM_UNKNOWN_18_5 0x00000020 /* ? */
+#define CM_FLINKOFF 0x00000020 /* force modem link detection off, model 037 */
#define CM_MIDSMP 0x00000010 /* 1/2 interpolation at front end DAC */
#define CM_UPDDMA_MASK 0x0000000C /* TDMA position update notification */
#define CM_UPDDMA_2048 0x00000000
unsigned int idx = snd_ctl_get_ioffidx(kcontrol, &ucontrol->id);
unsigned long flags;
+ /* Limit: emu->spdif_bits */
+ if (idx >= 3)
+ return -EINVAL;
spin_lock_irqsave(&emu->reg_lock, flags);
ucontrol->value.iec958.status[0] = (emu->spdif_bits[idx] >> 0) & 0xff;
ucontrol->value.iec958.status[1] = (emu->spdif_bits[idx] >> 8) & 0xff;
struct snd_ctl_elem_value *ucontrol)
{
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
- int channel;
+ unsigned int channel;
channel = (kcontrol->private_value) & 0xff;
+ /* Limit: emu1010_output_dst, emu->emu1010.output_source */
+ if (channel >= 24)
+ return -EINVAL;
ucontrol->value.enumerated.item[0] = emu->emu1010.output_source[channel];
return 0;
}
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
int change = 0;
unsigned int val;
- int channel;
+ unsigned int channel;
+ val = ucontrol->value.enumerated.item[0];
+ if (val >= 53)
+ return -EINVAL;
channel = (kcontrol->private_value) & 0xff;
- if (emu->emu1010.output_source[channel] != ucontrol->value.enumerated.item[0]) {
- val = emu->emu1010.output_source[channel] = ucontrol->value.enumerated.item[0];
+ /* Limit: emu1010_output_dst, emu->emu1010.output_source */
+ if (channel >= 24)
+ return -EINVAL;
+ if (emu->emu1010.output_source[channel] != val) {
+ emu->emu1010.output_source[channel] = val;
change = 1;
snd_emu1010_fpga_link_dst_src_write(emu,
emu1010_output_dst[channel], emu1010_src_regs[val]);
struct snd_ctl_elem_value *ucontrol)
{
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
- int channel;
+ unsigned int channel;
channel = (kcontrol->private_value) & 0xff;
+ /* Limit: emu1010_input_dst, emu->emu1010.input_source */
+ if (channel >= 22)
+ return -EINVAL;
ucontrol->value.enumerated.item[0] = emu->emu1010.input_source[channel];
return 0;
}
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
int change = 0;
unsigned int val;
- int channel;
+ unsigned int channel;
+ val = ucontrol->value.enumerated.item[0];
+ if (val >= 53)
+ return -EINVAL;
channel = (kcontrol->private_value) & 0xff;
- if (emu->emu1010.input_source[channel] != ucontrol->value.enumerated.item[0]) {
- val = emu->emu1010.input_source[channel] = ucontrol->value.enumerated.item[0];
+ /* Limit: emu1010_input_dst, emu->emu1010.input_source */
+ if (channel >= 22)
+ return -EINVAL;
+ if (emu->emu1010.input_source[channel] != val) {
+ emu->emu1010.input_source[channel] = val;
change = 1;
snd_emu1010_fpga_link_dst_src_write(emu,
emu1010_input_dst[channel], emu1010_src_regs[val]);
int change = 0;
val = ucontrol->value.enumerated.item[0] ;
+ /* Limit: uinfo->value.enumerated.items = 4; */
+ if (val >= 4)
+ return -EINVAL;
change = (emu->emu1010.internal_clock != val);
if (change) {
emu->emu1010.internal_clock = val;
* update the capture volume from the cached value
* for the particular source.
*/
- source_id = ucontrol->value.enumerated.item[0]; /* Use 2 and 3 */
+ source_id = ucontrol->value.enumerated.item[0];
+ /* Limit: uinfo->value.enumerated.items = 2; */
+ /* emu->i2c_capture_volume */
+ if (source_id >= 2)
+ return -EINVAL;
change = (emu->i2c_capture_source != source_id);
if (change) {
snd_emu10k1_i2c_write(emu, ADC_MUX, 0); /* Mute input */
struct snd_ctl_elem_value *ucontrol)
{
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
- int source_id;
+ unsigned int source_id;
source_id = kcontrol->private_value;
+ /* Limit: emu->i2c_capture_volume */
+ /* capture_source: uinfo->value.enumerated.items = 2 */
+ if (source_id >= 2)
+ return -EINVAL;
ucontrol->value.integer.value[0] = emu->i2c_capture_volume[source_id][0];
ucontrol->value.integer.value[1] = emu->i2c_capture_volume[source_id][1];
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
unsigned int ogain;
unsigned int ngain;
- int source_id;
+ unsigned int source_id;
int change = 0;
source_id = kcontrol->private_value;
+ /* Limit: emu->i2c_capture_volume */
+ /* capture_source: uinfo->value.enumerated.items = 2 */
+ if (source_id >= 2)
+ return -EINVAL;
ogain = emu->i2c_capture_volume[source_id][0]; /* Left */
ngain = ucontrol->value.integer.value[0];
if (ngain > 0xff)
if (ogain != ngain) {
if (emu->i2c_capture_source == source_id)
snd_emu10k1_i2c_write(emu, ADC_ATTEN_ADCL, ((ngain) & 0xff) );
- emu->i2c_capture_volume[source_id][0] = ucontrol->value.integer.value[0];
+ emu->i2c_capture_volume[source_id][0] = ngain;
change = 1;
}
ogain = emu->i2c_capture_volume[source_id][1]; /* Right */
if (ogain != ngain) {
if (emu->i2c_capture_source == source_id)
snd_emu10k1_i2c_write(emu, ADC_ATTEN_ADCR, ((ngain) & 0xff));
- emu->i2c_capture_volume[source_id][1] = ucontrol->value.integer.value[1];
+ emu->i2c_capture_volume[source_id][1] = ngain;
change = 1;
}
unsigned int val;
unsigned long flags;
+ /* Limit: emu->spdif_bits */
+ if (idx >= 3)
+ return -EINVAL;
val = (ucontrol->value.iec958.status[0] << 0) |
(ucontrol->value.iec958.status[1] << 8) |
(ucontrol->value.iec958.status[2] << 16) |
u32 source;
val = ucontrol->value.enumerated.item[0] ;
+ if (val > 7)
+ return -EINVAL;
change = (emu->p16v_capture_source != val);
if (change) {
emu->p16v_capture_source = val;
u32 tmp;
val = ucontrol->value.enumerated.item[0] ;
+ if (val > 3)
+ return -EINVAL;
change = (emu->p16v_capture_channel != val);
if (change) {
emu->p16v_capture_channel = val;
nid = codec->start_nid;
for (i = 0; i < codec->num_nodes; i++, nid++) {
- if (get_wcaps(codec, nid) & AC_WCAP_POWER) {
- unsigned int pincap;
- /*
- * don't power down the widget if it controls eapd
- * and EAPD_BTLENABLE is set.
- */
- pincap = snd_hda_param_read(codec, nid, AC_PAR_PIN_CAP);
- if (pincap & AC_PINCAP_EAPD) {
- int eapd = snd_hda_codec_read(codec, nid,
- 0, AC_VERB_GET_EAPD_BTLENABLE, 0);
- eapd &= 0x02;
- if (power_state == AC_PWRST_D3 && eapd)
- continue;
+ unsigned int wcaps = get_wcaps(codec, nid);
+ if (wcaps & AC_WCAP_POWER) {
+ unsigned int wid_type = (wcaps & AC_WCAP_TYPE) >>
+ AC_WCAP_TYPE_SHIFT;
+ if (wid_type == AC_WID_PIN) {
+ unsigned int pincap;
+ /*
+ * don't power down the widget if it controls
+ * eapd and EAPD_BTLENABLE is set.
+ */
+ pincap = snd_hda_param_read(codec, nid,
+ AC_PAR_PIN_CAP);
+ if (pincap & AC_PINCAP_EAPD) {
+ int eapd = snd_hda_codec_read(codec,
+ nid, 0,
+ AC_VERB_GET_EAPD_BTLENABLE, 0);
+ eapd &= 0x02;
+ if (power_state == AC_PWRST_D3 && eapd)
+ continue;
+ }
}
snd_hda_codec_write(codec, nid, 0,
AC_VERB_SET_POWER_STATE,
/* front */
snd_hda_codec_setup_stream(codec, nids[HDA_FRONT], stream_tag,
0, format);
- if (mout->hp_nid && mout->hp_nid != nids[HDA_FRONT])
+ if (!mout->no_share_stream &&
+ mout->hp_nid && mout->hp_nid != nids[HDA_FRONT])
/* headphone out will just decode front left/right (stereo) */
snd_hda_codec_setup_stream(codec, mout->hp_nid, stream_tag,
0, format);
/* extra outputs copied from front */
for (i = 0; i < ARRAY_SIZE(mout->extra_out_nid); i++)
- if (mout->extra_out_nid[i])
+ if (!mout->no_share_stream && mout->extra_out_nid[i])
snd_hda_codec_setup_stream(codec,
mout->extra_out_nid[i],
stream_tag, 0, format);
if (chs >= (i + 1) * 2) /* independent out */
snd_hda_codec_setup_stream(codec, nids[i], stream_tag,
i * 2, format);
- else /* copy front */
+ else if (!mout->no_share_stream) /* copy front */
snd_hda_codec_setup_stream(codec, nids[i], stream_tag,
0, format);
}
hda_nid_t dig_out_nid; /* digital out audio widget */
int max_channels; /* currently supported analog channels */
int dig_out_used; /* current usage of digital out (HDA_DIG_XXX) */
+ int no_share_stream; /* don't share a stream with multiple pins */
};
int snd_hda_multi_out_dig_open(struct hda_codec *codec,
break;
}
+ /* AD1986A has a hardware problem that it can't share a stream
+ * with multiple output pins. The copy of front to surrounds
+ * causes noisy or silent outputs at a certain timing, e.g.
+ * changing the volume.
+ * So, let's disable the shared stream.
+ */
+ spec->multiout.no_share_stream = 1;
+
return 0;
}
unsigned int alt_switch: 1;
unsigned int hp_detect: 1;
unsigned int gpio_mute: 1;
- unsigned int no_vol_knob :1;
unsigned int gpio_mask, gpio_data;
return 1;
}
-static int stac92xx_volknob_info(struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_info *uinfo)
-{
- uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER;
- uinfo->count = 1;
- uinfo->value.integer.min = 0;
- uinfo->value.integer.max = 127;
- return 0;
-}
-
-static int stac92xx_volknob_get(struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_value *ucontrol)
-{
- ucontrol->value.integer.value[0] = kcontrol->private_value & 0xff;
- return 0;
-}
-
-static int stac92xx_volknob_put(struct snd_kcontrol *kcontrol,
- struct snd_ctl_elem_value *ucontrol)
-{
- struct hda_codec *codec = snd_kcontrol_chip(kcontrol);
- unsigned int val = kcontrol->private_value & 0xff;
-
- if (val == ucontrol->value.integer.value[0])
- return 0;
-
- val = ucontrol->value.integer.value[0];
- kcontrol->private_value &= ~0xff;
- kcontrol->private_value |= val;
-
- snd_hda_codec_write_cache(codec, kcontrol->private_value >> 16, 0,
- AC_VERB_SET_VOLUME_KNOB_CONTROL, val | 0x80);
- return 1;
-}
-
-
static struct hda_verb stac9200_core_init[] = {
/* set dac0mux for dac converter */
{ 0x07, AC_VERB_SET_CONNECT_SEL, 0x00},
.private_value = verb_read | (verb_write << 16), \
}
-#define STAC_VOLKNOB(knob_nid) \
- { \
- .iface = SNDRV_CTL_ELEM_IFACE_MIXER, \
- .name = "Master Playback Volume", \
- .count = 1, \
- .info = stac92xx_volknob_info, \
- .get = stac92xx_volknob_get, \
- .put = stac92xx_volknob_put, \
- .private_value = 127 | (knob_nid << 16), \
- }
-
-
static struct snd_kcontrol_new stac9200_mixer[] = {
HDA_CODEC_VOLUME("Master Playback Volume", 0xb, 0, HDA_OUTPUT),
HDA_CODEC_MUTE("Master Playback Switch", 0xb, 0, HDA_OUTPUT),
},
STAC_INPUT_SOURCE(2),
STAC_ANALOG_LOOPBACK(0xFE0, 0x7E0),
- STAC_VOLKNOB(0x24),
HDA_CODEC_VOLUME_IDX("Capture Volume", 0x0, 0x1b, 0x0, HDA_INPUT),
HDA_CODEC_MUTE_IDX("Capture Switch", 0x0, 0x1d, 0x0, HDA_OUTPUT),
/* This needs to be generated dynamically based on sequence */
static struct snd_kcontrol_new stac922x_mixer[] = {
STAC_INPUT_SOURCE(2),
- STAC_VOLKNOB(0x16),
HDA_CODEC_VOLUME_IDX("Capture Volume", 0x0, 0x17, 0x0, HDA_INPUT),
HDA_CODEC_MUTE_IDX("Capture Switch", 0x0, 0x17, 0x0, HDA_INPUT),
HDA_CODEC_VOLUME_IDX("Mux Capture Volume", 0x0, 0x12, 0x0, HDA_OUTPUT),
static struct snd_kcontrol_new stac927x_mixer[] = {
STAC_INPUT_SOURCE(3),
- STAC_VOLKNOB(0x24),
STAC_ANALOG_LOOPBACK(0xFEB, 0x7EB),
HDA_CODEC_VOLUME_IDX("Capture Volume", 0x0, 0x18, 0x0, HDA_INPUT),
}
if (spec->multiout.hp_nid) {
const char *pfx;
- if (old_num_dacs == spec->multiout.num_dacs &&
- spec->no_vol_knob)
+ if (old_num_dacs == spec->multiout.num_dacs)
pfx = "Master";
else
pfx = "Headphone";
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac9200_pin_nids);
spec->pin_nids = stac9200_pin_nids;
- spec->no_vol_knob = 1;
spec->board_config = snd_hda_check_board_config(codec, STAC_9200_MODELS,
stac9200_models,
stac9200_cfg_tbl);
codec->spec = spec;
spec->num_pins = ARRAY_SIZE(stac925x_pin_nids);
spec->pin_nids = stac925x_pin_nids;
- spec->no_vol_knob = 1;
spec->board_config = snd_hda_check_board_config(codec, STAC_925x_MODELS,
stac925x_models,
stac925x_cfg_tbl);
codec->owner = THIS_MODULE;
codec->dai = &cs4270_dai;
codec->num_dai = 1;
- codec->private_data = codec + ALIGN(sizeof(struct snd_soc_codec), 4);
+ codec->private_data = (void *) codec +
+ ALIGN(sizeof(struct snd_soc_codec), 4);
socdev->codec = codec;
#include <asm/hardware.h>
#include <asm/io.h>
-#include <asm/arch/regs-ac97.h>
+#include <asm/plat-s3c/regs-ac97.h>
#include <asm/arch/regs-gpio.h>
#include <asm/arch/regs-clock.h>
#include <asm/arch/audio.h>
projects / cascardo / linux.git / commitdiff